Progress Lighting AirPro P250002 Mode d'emploi

Ceiling Fan Installation Manual

P250002

93099665_A

Date Purchased

Store Purchased

Model No.

Serial No.

Vendor No.

UPC

109226

Limited Lifetime Warranty

Progress Lighting fan motors are warranted to the original purchaser to be free of electrical and/or mechanical defects for so

long as the original purchaser owns the fan. Pull chain switches, reverse switches, capacitors and metal finishes are warranted to

be free from defects in materials or workmanship for a period of 1 year from the date of purchase. Warping of wooden or plastic

blades is not covered by this warranty nor is corrosion and/or deterioration of any finishes for fans installed within ten miles of

any sea coast. Extended warranties for ENERGY STAR

®

qualified products may apply.

Progress Lighting ceiling fans with built-in LED light sources, when properly installed and under normal conditions of use, are

warranted to be free from defects in material and workmanship which cause the light sources to fail to operate in accordance

with the specifications for (i) five (5) years from the date of purchase on the LED Light modules and electrical components for

fans used in single family residences, and (ii) three (3) years from the date of purchase on the LED Light modules and electrical

components for fans used in multi-family or commercial applications. LED bulbs supplied by Progress Lighting carry no

warranty other than manufacturer’s warranty. Non-LED bulbs carry no warranty.

With proof of purchase, the original purchaser may return the defective fan to the place of purchase during the first 30 days for

replacement. After 30 days, the original purchaser MUST contact Progress Lighting at (864) 678-1000 for repair or replacement

which shall be determined in Progress Lighting’s sole discretion and shall be purchaser’s sole and exclusive remedy.

Labor and Shipping Excluded. This warranty does not cover any costs or fees associated with the labor (including, but not

limited to, electrician’s fees) required to install, remove, or replace a fan or any fan parts.

This warranty shall not apply to any loss or damage resulting from (i) normal wear and tear or alteration, misuse, abuse or

neglect, or (ii) improper installation, operation, repair or maintenance by original purchaser or a third party, including without

limitation improper voltage supply or power surge, use of improper parts or accessories, unauthorized repair (made or

attempted) or failure to provide maintenance to the fan.

THE FOREGOING WARRANTIES STATE PROGRESS LIGHTING’S ENTIRE WARRANTY OBLIGATION AND

ORIGINAL PURCHASER’S SOLE AND EXCLUSIVE REMEDY RELATED TO SUCH PRODUCTS. PROGRESS

LIGHTING IS NOT RESPONSIBLE FOR DAMAGES (INCLUDING INDIRECT, SPECIAL, INCIDENTIAL OR

CONSEQUENTIAL), DUE TO PRODUCT FAILURE, WHETHER ARISING OUT OF BREACH OF WARRANTY,

BREACH OF CONTRACT, OR OTHERWISE. THIS WARRANTY IS GIVEN IN LIEU OF ALL OTHER WARRANTIES,

WHETHER EXPRESSED OR IMPLIED, INCLUDING THOSE OF MERCHANTABILITY, FITNESS FOR A PARTICULAR

PURPOSE OR NONINFRINGEMENT.

Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limitations of incidental or

consequential damages, so the above limitations and exclusions may not apply to you. This warranty gives you specific rights

and you may have other rights which vary from state to state.

785247000000

Table of Contents

Safety Rules.....................................................................................................................................................................................

Unpacking Your Fan .......................................................................................................................................................................

Installing Your Fan .........................................................................................................................................................................

Installing the Light Kit....................................................................................................................................................................

Installing the Fan without the Light Kit (optional) .......................................................................................................................

Operating Your Transmitter ..........................................................................................................................................................

Care of Your Fan ...........................................................................................................................................................................

Troubleshooting ............................................................................................................................................................................

Specifications ................................................................................................................................................................................

1.

2.

3.

9.

10.

12.

13.

14.

15.

1. Safety Rules

1. To reduce the risk of electric shock, insure electricity has been turned off

at the circuit breaker or fuse box before beginning.

2. All wiring must be in accordance with the National Electrical Code and

local electrical codes. Electrical installation should be performed by a

qualified licensed electrician.

3. WARNING: To reduce the risk of electrical shock and fire, do not use

this fan with any solid-state fan speed control device.

4. WARNING: To reduce the risk of fire, electric shock, or personal injury,

mount to outlet box marked "Acceptable for Fan Support of 15.9 kg (35 lbs.)

Or Less" and use mounting screws provided with the outlet box. Most outlet

boxes commonly used for the support of light fixtures are not acceptable for

fan support and may need to be replaced. Due to the complexity of the

installation of this fan, a qualified licensed electrician is strongly

recommended.

WARNING

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR PERSONAL

INJURY, MOUNT FAN TO OUTLET BOX MARKED ACCEPTABLE FOR

FAN SUPPORT.

5. The outlet box and support structure must be securely mounted and

capable of reliably supporting a minimum of 35 lbs (15.9 kg) or less.

Use only cUL-listed outlet boxes marked FOR FAN SUPPORT.

6. The fan must be mounted with a minimum of 7 ft (2.1m) clearance from

the trailing edge of the blades to the floor.

7. To operate the reverse function on this fan, press the reversing button while

the fan is running.

8. Avoid placing objects in the path of the blades.

9. To avoid personal injury or damage to the fan and other items, be

cautious when working around or cleaning the fan.

10. Do not use water or detergents when cleaning the fan or fan blades. A

dry dust cloth or lightly dampened cloth will be suitable for most

cleaning.

11. After making electrical connections, spliced conductors should be

turned upward and pushed carefully up into the outlet box. The wires

should be spread apart with the grounded conductor and the

equipment-grounding conductor on one side of the outlet box.

12. Electrical diagrams are for reference only. Light kits that are not packed

with the fan must be cUL Listed and marked suitable for use with the

model fan you are installing. Switches must be cUL General Use

Switches. Refer to the Instructions packaged with the light kits

NOTE

READ AND SAVE ALL INSTRUCTIONS!

WARNING

TO REDUCE THE RISK OF PERSONAL INJURY, DO NOT BEND THE

BLADE ARMS (ALSO REFERRED TO AS BRACKETS) DURING

ASSEMBLY OR AFTER INSTALLATION. DO NOT INSERT OBJECTS IN

THE PATH OF THE BLADES.

Unpack your fan and check the contents. You should have the following items:

Unpacking Your Fan 2.

1. Fan blades (3)

2. Canopy assembly

3. Ball/downrod assembly

4. Coupling cover

5. Fan motor assembly

6. Mounting plate

7. 18 Watt LED light kit assembly

8. Decorative ring

9. Metal light cover

10. Remote control

11. 12V MN21/A23 battery

12. Balancing kit

3

1

2

8

10

4

9

5

6

7

11

12

13. Loose parts bag containing:

a. Blade attachment hardware

(10 screws, 10 lock washers,

10 flat washers)

b. Mounting hardware

Wire nuts (3)

13

a

b

Tools Required

Phillips screw driver, straight slot screw driver,

adjustable wrench, step ladder, and wire cutters.

Mounting Options

If there isn't an existing cUL listed mounting

box, then read the following instructions.

Disconnect the power by removing fuses or

turning off circuit breakers.

Secure the outlet box directly to the building

structure. Use appropriate fasteners and building

materials. The outlet box and its support must be

able to fully support the moving weight of the

fan (at least 35 lbs). Do not use plastic outlet

boxes.

Figure 4

Figure 3

Figure 1

Figure 2

Outlet box

Note: You may need a longer downrod to

maintain proper blade clearance when installing

on a steep, sloped ceiling.

To hang your fan where there is an existing

fixture but no ceiling joist, you may need an

installation hanger bar as shown in Figure 4

(available at your Progress Lighting Retailer).

3. Installing Your Fan

WARNING

TO REDUCE THE RISK OF FIRE, ELECTRIC

SHOCK, OR OTHER PERSONAL INJURY,

MOUNT FAN ONLY TO AN OUTLET BOX

MARKED ACCEPTABLE FOR FAN SUPPORT

AND USE THE MOUNTING SCREWS

PROVIDED WITH THE OUTLET BOX. OUTLET

BOXES COMMONLY USED FOR THE

SUPPORT OF LIGHTING FIXTURES MAY NOT

BE ACCEPTABLE FOR FAN SUPPORT AND

MAY NEED TO BE REPLACED. CONSULT A

QUALIFIED ELECTRICIAN IF IN DOUBT.

Angled ceiling

maximum

20 angle

Recessed

outlet box

Provide strong support

Ceiling

hanger

bracket

4.

Hanging the Fan

REMEMBER to turn off the power. Follow

the steps below to hang your fan properly:

Step 1. Remove the decorative canopy bottom

cover from the canopy by turning the cover

counter clockwise.(Fig. 5)

Step 2. Remove the mounting bracket from

the canopy by removing the 1 of 2 screws

from the bottom of the mounting bracket and

loosening the other one a half turn from the

screw head. Next, turn the canopy counter

clockwise to removing the mounting bracket

from the canopy. (Fig. 5)

Step 3. Pass the 120-volt supply wires

through the center hole in the ceiling hanger

bracket as shown in Fig. 6.

Step 4. Secure the hanger bracket to the

ceiling outlet box with the screws and

washers provided with your outlet box.

Step 5. Remove the hanger pin, lock pin and

set screws from the top of the motor

assembly. (Fig. 7)

Step 6. Route the safety cable and wires

exiting from the top of the fan motor through

the collar cover, canopy cover, canopy and

then through the ball / downrod. (Fig. 7)

Step 7. Align the holes at the bottom of the

downrod with the holes in the collar on top of

the motor housing (Fig. 7). Carefully insert

the hanger pin through the holes in the collar and

downrod. Be careful not to jam the pin against the

wiring inside the downrod. Insert the locking pin

through the hole near the end of the hanger pin until it

snaps into its locked position, as noted in the circle

inset of Fig. 7.

WARNING

FAILURE TO PROPERLY INSTALL

LOCKING PIN AS NOTED IN STEP 7

COULD RESULT IN FAN LOOSENING AND

POSSIBLY FALLING.

Figure 6

Figure 7

Ceiling

hanger

bracket

Mounting screws

(supplied with

electrical box)

CUL Listed

electrical

box

120V Wires

Washers

Supply wires

Safety cable

Downrod

Hanger pin

Lock pin

Set screws

Canopy

Canopy cover

Collar cover

Pin in locked

position

Step 8. Tighten two set screws on top of the fan

motor firmly. (Fig. 7)

Step 9. Place the downrod ball into the hanger

bracket socket.

Step 10. Secure the safety cable to the building

structure with a wood screw. (wood screw not

supplied)

Figure 5

Ceiling hanger

bracket

Ceiling

canopy

Canopy

cover

5.

Make the Electric

Connections

WARNING: To avoid possible electrical shock,

be sure electricity is turned off at the main fuse box

before wiring.

Step 1. Motor to House Supply Wires Electrical

Connections: Connect the WHITE wire (Neutral)

from the outlet box to the WHITE wire marked

"AC in N" from the motor. (Fig. 8)

Step 2. Connect the BLACK wire (Hot) from the

outlet box to the BLACK wire marked "AC in L"

from the motor. (Fig. 8)

Secure all wire connections with the plastic wire

nuts provided.

Figure 8

Outlet Box

Black ("AC IN L")

White ("AC IN N")

White (Neutral)

Black (Hot)

Green or bare

copper (ground)

Ground (green)

(Connect to ground

wire on hanger

bracket if no house

ground wire exists.)

6.

Finishing the Installation

Step 1. Tuck connections neatly into ceiling outlet

box.

Step 2. Slide the canopy up to mounting bracket and

place the key hole on the canopy over the screw on

the mounting bracket, turn canopy until it locks in

place at the narrow section of the key holes. (Fig. 9)

Step 3. Align the circular hole on canopy with the

remaining hole on the mounting bracket, secure by

tightening the two set screws. Note: Adjust the

canopy screws as necessary until the canopy and

canopy cover are snug.

WARNING

Make sure the notch on the hanging bracket properly

sits in the groove in the hanger ball before attaching

the canopy to the bracket by turning the housing until

it drops into place.

Outlet box

Canopy

cover

Canopy

Hanger

bracket

Figure 9

Screws

7.

Attaching the Fan

Blades

Fasten the blade assembly to the motor using the

screws, lock washers and flat washers provided.

Be sure to tighten all screws. (Figure 10)

Figure 10

Flat washer

Screws

Lock washer

Blade

Blade Balancing

All blades are grouped by weight. Because

natural woods very in density, the fan may

wobble even though the blades are weighed

equally.

The following procedure should correct most

fan wobbling problems. Check after each step.

1. Check that all blade and blade arm screws are

secure.

2. Most fan wobbling problems are caused

when blade levels are unequal. Check this

level by selecting a point on the ceiling

above the tip of one of the blades. Measure

this distance as shown in Figure 11. Rotate

the fan until the next blade is positioned for

measurement. Repeat for each blade. The

distance deviation should be equal within

1/8".

3. Use the enclosed Blade Balancing Kit if the

blade wobble is still noticeable.

4. If the blade wobble is still noticeable,

interchanging two adjacent (side by side)

blades can redistribute the weight and

possibly result in smoother operation.

Touching

ceiling

Figure 11

WARNING

TO REDUCE THE RISK OF PERSONAL

INJURY, DO NOT BEND THE BLADE

HOLDERS WHILE INSTALLING,

BALANCING THE BLADES, OR CLEANING

THE FAN. DO NOT INSERT FOREIGN

OBJECTS BETWEEN ROTATING FAN

BLADES.

8.

Installing the Mounting

Plate

Step 1. Remove 1 of the 3 screws from the

mounting ring and loosen the other 2 screws. (Do

not remove)

Step 2. Place the key holes on the mounting plate

over the 2 screws previously loosened from the

mounting ring, turn mounting plate until it locks in

place at the narrow section of the key holes.

Secure by tightening the 2 screws previously

loosened and the one previously removed. (Fig.

12)

Figure 12

Mounting

plate

Mounting ring

Screws

9.

Installing the Light Kit

CAUTION: Before starting installation,

disconnect the power by turning off the circuit

breaker or removing the fuse at fuse box.

Turning power off using the fan switch is not

sufficient to prevent electric shock.

NOTE: If you do not wish to install the light

kit, skip steps 9 and proceed to step 10.

1. Remove the 2 screws from the mounting plate.

2. While holding the LED light kit under the fan

motor assembly, make the 2-pin wire connections:

(Fig. 13)

- White to white

- Black to blue

3. Place the LED light kit to the mounting plate.

Align the mounting holes with the holes in the

light kit and mounting plate, and fasten using the

two screws previously removed. (Fig. 13)

4. Slide the decorative ring up to light kit

assembly and place the key hole on the decorative

ring over the two screw on the light kit, turn

decorative ring until it locks in place at the narrow

section of the key holes. (Fig. 14)

Figure 13 Figure 14

Screws

Mounting

plate

Wire connector

LED Light kit

assembly

Screws

Decorative

ring

Installing the Fan without the Light Kit (optional)

10.

NOTE: The metal light cover included with your

fan is an option to replace the plastic shade for

the light in the event that you prefer not to use

the light feature of your fan.

1. Disassemble the plastic shade from the light

kit. You can keep the plastic shade for future use.

(Fig. 15)

2. Installing metal light cover to the LED light

kit with the two screws previously removed.

(Fig. 15)

3. Remove the 2 screws from the mounting plate.

(Fig. 16)

4. Place the LED light kit to the mounting plate.

Align the mounting holes with the holes in the

light kit and mounting plate, and fasten using the

two screws previously removed. (Fig. 16)

5. Slide the decorative ring up to light kit

assembly and place the key hole on the

decorative ring over the two screw on the light

kit, turn decorative ring until it locks in place at

the narrow section of the key holes. (Fig. 16)

NOTE: Do Not connect the 2-pin wire

connectores before installing the metal light

cover.

Figure 15

Figure 16

Screws

Plastic

shade

LED Light kit

assembly

Screws

Metal light

cover

LED Light kit

assembly

Screws

Decorative

ring

Mounting

plate

Wire connector

11. Operating Your Transmitter

Remote Control Button Definitions:

These six buttons are used to set the fan speed as

follows:

I = minimum speed

II = low speed

III = medium low speed

IV = medium speed

V = medium high speed

VI = high speed

button: Turns the fan off.

button: Controls fan direction.

button: Controls light. Switch the “D” and “ON” dip

switch on the back of transmitter to decide the light in

“ON/OFF” or “Dimmable” condition.

Your DC brushless motor is equipped with an

automatically learned type remote control. There are

no frequency switches on the receiver; the receiver

unit will automatically scan the frequency from the

remote control if any changes are made. The

frequency settings on the transmitter should be

changed ONLY in case of interference or if a

second or more ceiling fans with the same type of

control system are installed in the same structure.

Setting the Remote Control

Follow the below steps to set the remote control:

The auto learning function will only mandate within

60 seconds when turning the fan’s AC power ON.

a) Select desired frequency from the transmitter.

The

dip switches can be set to 16 different combinations.

(Fig. 19)

b) From the back of the transmitter,

with the

fan’s power off, restore power to the fan. Press

and hold “SET” button for about 5 seconds and

release. If optional light kit is installed, the

light kit will flash twice and the signal light on

the hand held transmitter will come on when

the button is pressed. The fan has completed

the pairing process with the remote control and

is ready for use. (Fig. 19)

NOTE: If the self calibration test failed, turn the AC

power off; restore power and process the self

calibration test again.

NOTE: During self calibration test, the remote is

non-fuctional.

NOTE: The learning frequency function and self

calibration test will continue to retain the last set

frequency and calibration set even when the AC

power is shut off. If the frequency is changed the self

calibration test will occur again.

“D” and “ON” dip switch:

1. The “ON” selection is the light dimmable selection

and is to be used with all bulbs except for CFL bulbs.

The “D” selection is the light ON only (no dimming

function) and is to be used with CFL bulbs as CFL

bulbs in most cases cannot be used with dimming

controllers.

(Fig. 19)

Installing the battery

Install a 12V MN21/A23 battery (included) into the

remote control. To prevent damage to the remote

control, remove the battery if not used for long

periods. (Fig. 17)

Figure 17

ON ECE

1234

This receiver provides the following protective function:

1. Lock Rotor Position: The DC motor has a built-in safety

against a stalled or locked rotor condition (stalled blade

rotation). If there is an obstruction or fault with the motor, the

current monitoring function will automatically turn power off

to the motor after 30 seconds. Remove the obstruction and turn

the AC power off. Restore power and re-start fan motor.

2. Over 80W protection: When the receiver detects motor

power consumption which is greater than 80W, the receiver

power will be stopped and operation will immediately

discontinue. Wait for 5 seconds and then turn the receiver

power back on.

Speed settings for warm or cool weather depend on factors

such as the room size. Ceiling height, number of fans and so

on.

NOTE: To operate the reverse function on this fan, press

the reverse button while the fan is running.

Warm weather - (Forward) A downward airflow creates a

cooling effect as shown in Fig. 20. This allows you to set

your air conditioner on a warmer setting without affecting

your comfort.

Cool weather - (Reverse) An upward airflow moves warm

air off the ceiling area as shown in Fig. 21. This allows you

to set your heating unit on a cooler setting without affecting

your comfort.

Figure 20

Figure 21

12.

Figure 19

Figure 18

ON ECE

1234

ON ECE

1234

Here are some suggestions to help you maintain your

fan

1. Because of the fan's natural movement, some

connections may become loose.

Check the support

connections, brackets, and blade attachments

twice a year.

Make sure they are secure.

(It is not

necessary to remove fan from ceiling.)

2. Clean your fan periodically to help maintain its new

appearance over the years. Use only a soft brush or

lint-free cloth to avoid scratching the finish. The

plating is sealed with a lacquer to minimize

discoloration or tarnishing. Do not use water when

cleaning. This could damage the motor, or the wood,

or possibly cause an electrical shock.

3. You can apply a light coat of furniture polish to the

wood blades for additional protection and enhanced

beauty. Cover small scratches with a light application

of shoe polish.

4.

There is no need to oil your fan.

The motor has

permanently lubricated bearings.

IMPORTANT

MAKE SURE THE POWER IS OFF AT THE

ELECTRICAL PANEL BOX BEFORE YOU

ATTEMPT ANY REPAIRS. REFER TO THE

SECTION "MAKING ELECTRICAL

CONNECTIONS"

13.

Care of Your Fan

Troubleshooting

14.

Solution

1. Check circuit fuses or breakers.

2. Check line wire connections to the fan and switch wire connections in the switch housing.

CAUTION: Make sure main power is off.

3. Check to make sure the dip switches from the transmitter and receiver are set to the same frequency.

1. Make sure all motor housing screws are snug.

2. Make sure the screws that attach the fan blade bracket to the motor hub is tight.

3. Make sure wire nut connections are not rubbing against each other or the interior wall of the switch housing.

CAUTION: Make sure main power is off.

4. Allow a 24-hour "breaking-in" period. Most noise associated with a new fan disappear during this time.

5. If using an optional light kit, make sure the screws securing the glassware are tight. Check that light bulb is also secure.

6. Some fan motors are sensitive to signals from solid-state variable speed controls. If you have installed this type of control,

choose and install another type of control.

7. Make sure the upper canopy is a short distance from the ceiling. It should not touch the ceiling.

1. Do not connect the fan with wall mounted variable speed control (s).

2. Make sure the dip switches are set correctly.

Problem

Fan will not start.

Fan sounds noisy.

Remote control

malfunction

15.

Specifications

2018 Progress Lighting, Inc.

701 Millennium Blvd.,

Greenville, SC 29607

c

14.11

lbs

17.26

lbs

2.31'

Fan Size

Speed

Volts

Amps

Watts

RPM

CFM

N.W. G.W. C.F.

60"

Low

High

120

These are approximate measures. They do not include Amps and Wattage used by the light kit.

0.07

0.43

3.31

31.45

51

165

1954.66

7047.29

Manuel d’installation du ventilateur de plafond

P250002

ĊăĀĊĊććĆĤ

UPC

109226

Garantie limitée à vie

Progress Lighting garantit à l’acheteur initial que les moteurs de ventilateur sont exempts de défauts électriques ou mécaniques

tant que l’acheteur initial est propriétaire du ventilateur. Les interrupteurs à chaînette, les interrupteurs inverseurs, les

condensateurs et les finis métalliques sont garantis contre les défauts de matériaux ou de fabrication pendant une période d’un

an à partir de la date d’achat. Le gauchissement des pales de bois ou de plastique n’est pas couvert par la présente garantie, ni la

corrosion ou la détérioration du fini des ventilateurs installés à moins de dix milles d’un bord de mer. Les garanties prolongées

pour les produits homologués ENERGY STAR® peuvent s’appliquer.

Lorsqu’ils sont installés correctement et dans des conditions d’utilisation normales, les ventilateurs de plafond Progress

Lighting dotés d’une source lumineuse à DEL intégrée sont garantis contre les défauts de matériaux et de fabrication causant le

non fonctionnement de la source lumineuse selon les spécifications pendant (i) cinq (5) ans à partir de la date d’achat des

modules d’éclairage à DEL et des composants électriques des ventilateurs pour les résidences unifamiliales et (ii) trois (3) ans à

partir de la date d’achat des modules d’éclairage à DEL et des composants électriques des ventilateurs pour les résidences

multifamiliales et pour les utilisations commerciales. Les ampoules à DEL fournies par Progress Lighting ne sont assorties

d’aucune autre garantie que celle du fabricant. Les ampoules autres qu’à DEL ne sont assorties d’aucune garantie.

En fournissant la preuve d’achat, l’acheteur initial peut retourner le ventilateur défectueux à son lieu d’achat pendant les 30

premiers jours afin qu’il soit remplacé. Après 30 jours, l’acheteur initial DOIT communiquer avec Progress Lighting au 864

678-1000 pour la réparation ou le remplacement du ventilateur, ce qui sera déterminé exclusivement par Progress Lighting et

constituera le seul et unique recours de l’acheteur.

Main-d’œuvre et expédition exclus. La présente garantie ne couvre par les coûts et les frais associés à la main-d’œuvre (y

compris, sans s’y limiter, les frais d’électricien) nécessaires à l’installation, au retrait ou au remplacement du ventilateur ou des

pièces du ventilateur.

La présente garantie ne s’applique pas en cas de perte ou de dommage découlant (i) de l’usure normale, de l’altération ou d’un

usage incorrect, abusif ou négligent ou (ii) d’une installation, d’une utilisation, d’une réparation ou d’un entretien inadéquats par

l’acheteur initial ou un tiers, y compris, sans s’y limiter, une tension électrique inadéquate ou une surtension, l’utilisation de

pièces ou d’accessoires inadéquats, une réparation non autorisée (effectuée ou tentée) ou l’omission d’entretenir le ventilateur.

LES GARANTIES QUI PRÉCÈDENT ÉNONCENT L’ENTIÈRE RESPONSABILITÉ DE PROGRESS LIGHTING AU

CHAPITRE DE LA GARANTIE AINSI QUE LE SEUL ET UNIQUE RECOURS DE L’ACHETEUR LIÉ À CES PRODUITS.

PROGRESS LIGHTING N’EST PAS RESPONSABLE DES DOMMAGES (Y COMPRIS LES DOMMAGES INDIRECTS,

SPÉCIAUX, ACCESSOIRES OU CONSÉCUTIFS) ATTRIBUABLES À LA DÉFECTUOSITÉ DU PRODUIT, QU’ILS

SOIENT LIÉS À UNE VIOLATION DE LA GARANTIE, UNE VIOLATION DU CONTRAT OU AUTRE. LA PRÉSENTE

GARANTIE REMPLACE TOUTE AUTRE GARANTIE, EXPRESSE OU IMPLICITE, Y COMPRIS TOUTE GARANTIE

DE QUALITÉ MARCHANDE, D’UTILITÉ À UNE FIN PARTICULIÈRE OU D’ABSENCE DE CONTREFAÇON.

Certains États ne permettent pas de limitation à la durée implicite d’une garantie ou d’exclusion ou de limitation des dommages

accessoires ou consécutifs. Par conséquent, les limitations ci-dessus pourraient ne pas s’appliquer à vous. La présente garantie

vous accorde des droits précis et vous pourriez avoir d’autres droits qui peuvent varier d’un État à l’autre.

785247000000

Date d’achat

Magasin

Nº de modèle.

Nº de série .

Nº du fournisseur

La page charge ...

Progress Lighting AirPro P250002 Mode d'emploi

Progress Lighting AirPro P250002 Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents