Whirlpool WTW4955HW Mode d'emploi

Marque: Whirlpool

Modèle: WTW4955HW

Catégorie: Machines à laver

Taper: Mode d'emploi

W11035364A

W11035698A-SP

Top-Loading

High Efficiency Washer

Use and Care Guide

Table of Contents

WASHER SAFETY ...................................................................... 2

WHAT’S UNDER THE LID .......................................................... 3

CONTROL PANEL AND FEATURES ......................................... 4

CYCLE GUIDE ............................................................................ 6

USING YOUR WASHER ............................................................. 8

WASHER MAINTENANCE ....................................................... 11

TROUBLESHOOTING .............................................................. 13

WARRANTY .............................................................................. 18

ASSISTANCE OR SERVICE ..................................BACK COVER

Table des matières

SÉCURITÉ DE LA LAVEUSE ................................................... 19

CE QUI EST SOUS LE COUVERCLE ...................................... 20

TABLEAU DE COMMANDE

ET CARACTÉRISTIQUES ........................................................ 21

GUIDE DES PROGRAMMES ................................................... 23

UTILISATION DE LA LAVEUSE ............................................... 25

ENTRETIEN DE LA LAVEUSE ................................................. 28

DÉPANNAGE ............................................................................ 30

GARANTIE ................................................................................ 37

ASSISTANCE OU SERVICE ............... COUVERTURE ARRIÈRE

Guide d’utilisation

et d’entretien de la laveuse

haute efficacité avec

chargement par le dessus

Para una versión de estas instrucciones en español, visite www.whirlpool.com

Designed to use only HE

(High Efciency) detergents.

Conçue pour l’utilisation d’un détergent

haute efcacité seulement.

Washer Safety

What’s Under the Lid

Use only High Efciency (HE) detergent.

IMPORTANT:

■ The lid must be closed before the washer basket lls with water and for the wash cycle to start. If the lid is opened, the cycle

pauses and all lling/agitation motion halts. Once the lid is closed, the cycle automatically resumes. However, if the Start/Pause/

Cancel button is pressed prior to opening the lid, the lid must be closed and the Start/Pause/Cancel button pressed again to

resume the cycle.

■ Rinse option must be set to Auto with Extra Rinse, Deep Water Rinse, or Deep Water with Extra Rinse when using fabric softener

in the fabric softener dispenser. This ensures that fabric softener is added at the correct time in the rinse phase and is evenly

distributed.

Lid Lock

To allow for higher spin speeds, the lid will lock and the Lid

Locked light will turn on. When this light is lit, the lid is locked

and cannot be opened without pausing the cycle. When this

light is blinking, the washer is paused. When this light is off,

the lid can be opened. After the cycle has started, the washer

will ll to the appropriate water level. On select cycles, agitation

will occur while the basket is lling with water. This is normal.

When the washer is done lling, it will begin the wash phase.

If you need to open the lid to add a garment after this point, the

lid will remain unlocked during the entire agitation portion of the

wash phase. The cycle will automatically pause when the lid is

opened, and the cycle will resume once the lid is closed. The

lid will lock before the spin phase begins. If you need to pause

or stop after this point, you must press the START/PAUSE/

CANCEL button and wait for the lid to unlock. The lid will only

unlock after washer movement has stopped. Depending on

when in the cycle you try to pause, it may take from several

seconds to several minutes for the lid to unlock. Press START/

PAUSE/CANCEL to resume the cycle.

Sensing

This washer automatically senses the load size for most cycles,

and chooses an appropriate water level according to the load

size detected. This washer also performs a series of spins to

check for load balance. During this time, a series of clicks and

a whirring noise signal that sensing technology is determining

if there is an off-balance load.

Water Level Options

Set the Water Level knob to the Auto Sensing setting and the

washer automatically adjusts the water level to the load size.

Set the Water Level knob to the Deep Water Wash setting and

the washer automatically adds more water to any cycle at any

time during the wash process.

Normal Sounds You Can Expect

At different stages of the wash cycle, you may hear sounds

and noises that are different from those of your previous washer.

For example, you may hear a clicking and hum at the beginning

of the spin phase, as the lid lock goes through a self-test. There

will be different kinds of humming sounds as the HE agitator

tests for load balance or moves the load. And sometimes, you

may hear nothing at all, as the washer determines the correct

water level for your load or allows time for clothes to soak.

Spray Rinse

Select cycles default to a spray rinse. During these cycles,

you will hear water enter the washer as the tub spins, allowing

the rinse water to penetrate clothes. Check the “Cycle Guide”

for details.

Choosing the Right Detergent

Use only High Efciency detergents. The package will be

marked “HE” or “High Efciency.” Using non-HE detergent

will likely result in longer cycle times and reduced rinsing

performance. It may also result in component malfunction and,

over time, buildup of mold or mildew. HE detergents should be

low-sudsing and quick-dispersing to produce the right amount

of suds for the best performance. They should hold soil in

suspension so it is not redeposited onto clean clothes. Not all

detergents labeled as High Efciency are identical in formulation

and their ability to reduce suds. For example, natural, organic,

or homemade HE detergents may generate a high level of suds.

Always follow the detergent manufacturer’s instructions to

determine the amount of detergent to use.

Control Panel and Features

SOIL LEVEL (on some models)

Select the setting most suitable for your load. For heavily

soiled and sturdy fabrics, select Heavy soil level for more

wash time. For lightly soiled and delicate fabrics, select Light

or Extra Light soil level for less wash time. A lighter soil level

setting will help reduce tangling and wrinkling.

WASH TEMP or WASH TEMPERATURE

Wash Temp senses and maintains uniform water

temperatures by regulating incoming hot and cold water.

Select a wash temperature based on the type of fabric

and soils being washed. For best results, use the warmest

wash water safe for your fabric, as speci ed by the garment

label instructions.

■ On some models and cycles, warm and hot water may

be cooler than your previous washer.

■ Even in a cold- and cool-water wash, some warm water

may be added to the washer to maintain a minimum

temperature.

All rinses are cold.

WASH CYCLE KNOB

Use the Wash Cycle knob to select cycles on your washer.

See “Cycle Guide” for detailed descriptions of cycles.

RINSE OPTION

Select the option most suitable for your load. Select Auto

with Extra Rinse, Deep Water Rinse, or Deep Water with

Extra Rinse if using fabric softener during a cycle. It ensures

that fabric softener is added at the correct time in the rinse

for even distribution.

WATER LEVEL

Set the Water Level knob to the Auto Sensing setting and the

washer will automatically sense the appropriate water level

for the load size and type.

Set the Water Level knob to the Deep Water Wash setting

and the washer will automatically add more water to any

cycle at any time during the wash process.

NOTE: Expect longer cycle times due to extended  ll times

when using the Deep Water Wash option.

START/PAUSE/CANCEL BUTTON

Press to start the selected cycle. Press again to pause the

cycle and unlock the lid. Close the lid and press to restart

the cycle. Press and hold to cancel a cycle and pump out

the washer.

NOTE: If the washer is spinning, it may take several minutes

to unlock the lid.

Not all features and options are available on all models.

Appearance may vary.

432

452

PROGRESS LIGHTS

The Progress Lights show the progress of a cycle. At each

stage of the process, you may notice sounds or pauses

that are different from traditional washers.

SENSING/FILL

When the Start/Pause/Cancel button is pressed

and the Water Level knob is set to Auto Sensing, the

washer will ll and begin sensing to determine load

size and balance. A short but noticeable pause in the

cycle action occurs during sensing. This is normal.

Once sensing is complete, the washer will ll to the

appropriate level for the detected load size and, on

select cycles, agitation will occur during lling. This,

too, is normal. When the washer is done lling, it will

begin the wash phase of the cycle. To ensure that

the most accurate load size is detected, avoid opening

the lid during the “Sensing” phase.

NOTE: Sensing and wash phases will be paused by

opening the unlocked lid. Close the lid to resume the

cycle. If the lid is left open for more than 10 minutes,

the washer will cancel the cycle and pump out the

water.

WASH

The washer will ll to the correct water level based

on the load size and the Water Level selection. Certain

cycles may agitate during the ll process to boost

cleaning. When the wash cycle begins, you will hear

the HE agitator increase speed. The motor sounds may

change at different stages in the wash cycle while the

washer performs different wash actions.

NOTE: The lid will automatically lock after the wash

phase completes and before the initial spinout occurs,

and will remain locked for the rest of the cycle.

RINSE

Certain cycles use a spray rinse, which adds water

to the tub while the basket spins. You may hear the

motor turning on briey (short hum) to move the basket

while lling. In some cases, you may also hear sounds

similar to the wash cycle as the washer lls, rinses,

and moves the load.

FINAL SPIN

The washer spins the load at increasing speeds for

proper water removal based on the selected cycle

and spin speed.

CYCLE COMPLETE

Once the cycle is complete, the lid will unlock and this

light will come on. For best results, remove the load

promptly.

LID LOCKED

The Lock feature allows for higher spin

speeds. When lit, the lid is locked and

cannot be opened without pausing the

cycle. When the light is off, the lid can

be opened.

To open the lid after it has been

locked, press START/PAUSE/

CANCEL. The lid will unlock once the

washer movement has stopped. This

may take several minutes if the load

was spinning at high speed. Press

START/PAUSE/CANCEL while the lid

is closed to resume the cycle.

Appearance

may vary

Cycle Guide

For best fabric care, choose the cycle that best ts the load being washed. Recommended settings for best performance are shown

in Bold. Not all cycles and options are available on all models.

Sturdy fabrics,

colorfast items,

towels, jeans

Heavy Hot

Warm

Cool

Cold

Tap Cold

High Use this cycle for heavily soiled or sturdy items. Water-level

sensing process may take longer for some items than for

others because they will absorb more water than other

fabric types.

Heavily soiled

white fabrics

Whites

with Soak

‡

Hot

Warm

Cool

Cold

Tap Cold

High This cycle, when used with chlorine bleach, improves

whitening of soiled white fabrics.

‡

To enhance cleaning, select Whites with Soak, which

automatically adds about 10 minutes of soak time after the

ll phase, and then automatically runs the Whites cycle.

Large items such

as sheets, sleeping

bags, small

comforters, jackets,

small, washable

rugs

Bulky/Sheets Hot

Warm

Cool

Cold

Tap Cold

Low Use this cycle to wash large items such as jackets and small

comforters. The washer will ll with enough water to wet

down the load before the wash portion of the cycle begins

and uses a higher water level than other cycles.

Cottons, linens,

and mixed loads

Normal Hot

Warm

Cool

Cold

Tap Cold

High Use this cycle for normally soiled cottons and mixed loads.

Bright and darkly

colored cottons

and mixed loads

Colors

with Soak

Hot

Warm

Cool

Cold

Tap Cold

High Use this cycle to wash darks and colors, including mixed

loads and activewear.

To enhance cleaning, select Colors with Soak, which

automatically adds about 10 minutes of soak time after the

ll phase, and then automatically runs the Colors cycle.

Machine-wash silks,

handwash fabrics

Delicates Hot

Warm

Cool

Cold

Tap Cold

Low Use this cycle to wash lightly soiled items indicating

“Machine Washable Silks” or “Gentle” cycle on the care

label. Place small items in mesh garment bags before

washing. This cycle uses a higher, preset water level.

Items to wash: Cycle: Wash Temp:* Spin

Speed:**

Cycle Details:

Cleaning

Gentleness

Efciency

†

Good

Best

Cleaning

Gentleness

Efciency

†

Good

Best

Cleaning

Gentleness

Efciency

†

Good

Best

Cleaning

Gentleness

Efciency

†

Good

Best

Cleaning

Gentleness

Efciency

†

Good

Best

Cleaning

Gentleness

Efciency

†

Good

Best

NOTE: If you are using fabric softener, be sure to select one of the following Rinse Option settings: Auto with Extra Rinse, Deep Water

Rinse, or Deep Water with Extra Rinse.

**All rinses are cold.

**Spin speed is integrated into the cycle and cannot be selected or modied.

†

Efcient use of resources, such as energy and water.

Small loads,

cottons, polyester,

permanent press

Quick Wash Hot

Warm

Cool

Cold

Tap Cold

High Use this cycle to wash small, lightly soiled loads of two or

three items that are needed in a hurry.

Swimsuits and

items requiring

rinsing without

detergent

Rinse &

Spin

Cold rinse only High Combines a rinse and high-speed spin for loads requiring

an additional rinse cycle. Use this cycle to complete a load

after power interruption or for loads that require rinsing only.

Hand-washed items

or dripping-wet

items

Drain &

Spin

N/A High This cycle uses a spin to shorten drying times for heavy

fabrics or special-care items washed by hand. Use this

cycle to drain washer after canceling a cycle or completing

a cycle after a power failure.

No clothes

in washer

Clean Washer

with affresh

Hot Low Use this cycle every 30 washes to keep the inside of your

washer fresh and clean. This cycle uses a higher water level.

Use with affresh

Washer Cleaner tablet or liquid chlorine

bleach to thoroughly clean the inside of your washer. This

cycle should not be interrupted. See “Washer Care.”

IMPORTANT: Do not place garments or other items in the

washer during the Clean Washer with affresh

cycle. Use

this cycle with an empty wash tub.

Items to wash: Cycle: Wash Temp:* Spin

Speed:**

Cycle Details:

Cleaning

Gentleness

Efciency

†

Good

Best

NOTE: If you are using fabric softener, be sure to select one of the following Rinse Option settings: Auto with Extra Rinse, Deep Water

Rinse, or Deep Water with Extra Rinse.

**All rinses are cold.

**Spin speed is integrated into the cycle and cannot be selected or modied.

†

Efcient use of resources, such as energy and water.

■ Empty pockets. Loose change, buttons, or any small

object can pass under the HE agitator and become

trapped, causing unexpected sounds.

■ Sort items by recommended cycle, water temperature,

and colorfastness.

■ Separate heavily soiled items from lightly soiled.

■ Separate delicate items from sturdy fabrics.

■ Do not dry garments if stains remain after washing

because heat can set stains into fabric.

■ Treat stains promptly.

■ Close zippers, fasten hooks, tie strings and sashes,

and remove non-washable trim and ornaments.

■ Mend rips and tears to avoid further damage to items

during washing.

Helpful Tips:

■ When washing water-proof or water-resistant items,

load evenly.

■ Use mesh garment bags to help avoid tangling when

washing delicate or small items.

■ Turn knits inside out to avoid pilling. Separate lint-takers

from lint-givers. Synthetics, knits, and corduroy fabrics will

pick up lint from towels, rugs, and chenille fabrics.

NOTE: Always read and follow fabric care label instructions

to avoid damage to your items.

1. Sort and prepare your laundry

Add a measured amount of HE

detergent or single-dose laundry

packet into the basket.

If using Oxi-type boosters, color-safe

bleach, or fabric-softener crystals, add

to the bottom of the washer basket before adding clothes.

IMPORTANT: Use only High Ef ciency detergents. The

package will be marked “HE” or “High Ef ciency.” Using

regular detergent will likely result in longer cycle times

and reduced rinsing performance. It may also result in

component failures and noticeable mold or mildew. HE

detergents are made to produce the right amount of suds

for the best performance.

NOTE: Follow the manufacturer’s instructions to determine

the amount of laundry products to use.

2. Add laundry products

Using Your Washer

5. Add fabric softener to dispenser

Pour a measured amount of liquid fabric

softener into dispenser; always follow

manufacturer’s directions for correct amount

of fabric softener based on your load size.

Dilute liquid fabric softener by  lling the dispenser with warm

water until liquid reaches the underside of the rim. See Max Fill

line arrows.

IMPORTANT: The Rinse Option knob must be set to Auto with

Extra Rinse, Deep Water Rinse, or Deep Water with Extra Rinse

when using fabric softener in the fabric softener dispenser. This

ensures that fabric softener is added at the correct time in the

rinse phase and is evenly distributed.

Adding Liquid Fabric Softener Manually

to Wash Load

During the  nal rinse, wait until the washer has completed

 lling and press the START/PAUSE/CANCEL button to pause

the washer. Lift the lid and add the measured, recommended

amount of liquid fabric softener. Do not use more than the

recommended amount. Close the lid and press the START/

PAUSE/CANCEL button again to start the washer.

Liquid

Chlorine Bleach

4. Add liquid chlorine bleach

to dispenser

Do not over ll, dilute, or use more than 1 cup (236 mL).

Do not use color-safe bleach or Oxi products in the same

cycle with liquid chlorine bleach.

Load garments in loose heaps evenly

around basket wall. For best results, do

not pack the load tightly. Do not wrap

large items such as sheets around the

HE agitator; load them in loose piles

around the sides of the basket. Try

mixing different-sized items to reduce

tangling.

IMPORTANT: Do not tightly pack or

force items into washer. Items need to move freely for best

cleaning and to reduce wrinkling and tangling.

3. Load laundry into washer

MAX FILL

Turn cycle knob to choose your wash cycle. For more

information, see “Cycle Guide.”

6. Select cycle

Appearance may vary

Fabric softener

Water

Wash Temp Suggested Fabrics

8. Select wash temp

or wash temperature

Once you select a cycle, select the wash temperature by

turning the Wash Temp or Wash Temperature knob to the

desired setting.

Always read and follow fabric care label instructions

to avoid damage to your items.

9. Select rinse option and water level

Select the number of rinses by turning the Rinse Option

knob to the desired setting.

IMPORTANT: The Rinse Option knob must be set to Auto

with Extra Rinse, Deep Water Rinse, or Deep Water with

Extra Rinse when using the fabric softener dispenser. This

ensures that fabric softener is added at the correct time in

the rinse for even distribution.

Set the Water Level knob to the Auto Sensing setting and

the washer will automatically sense the appropriate water

level for the load size and type.

Set the Water Level knob to the Deep Water Wash setting

and the washer will automatically add more water to any

cycle at any time during the wash cycle.

NOTE: The cycle will be longer due to extended  ll times

when using the Deep Water Wash setting.

Cool

Warm water is added to assist in

soil removal and to help dissolve

detergents. Cool is slightly warmer

than cold.

Dark colors that

bleed or fade

Light soils

Hot

Some cold water is added to save

energy. This may be cooler than

your hot water heater setting.

Warm

Some cold water will be added, so

this may be cooler than what your

previous washer provided.

Cold

Warm water may be added to

assist in soil removal and to help

dissolve detergents.

Whites and pastels

Durable items

Heavy soils

Bright colors

Moderate to light soils

Colors that bleed

or fade

Light soils

Dark colors that

bleed or fade

Light soils

Tap Cold

This is the temperature

from your faucet.

7. Select soil level (on some models)

Once you select a cycle, select the soil level by turning the

Soil Level knob to the desired setting.

10. Press START/PAUSE/CANCEL

to begin wash cycle

Press START/PAUSE/CANCEL to start the wash cycle. When

the cycle has  nished, the Cycle Complete progress light will

light. Promptly remove garments after cycle has completed

to avoid odor, reduce wrinkling, and avoid rusting of metal

hooks, zippers, and snaps.

Unlocking the lid to add garments

If you need to add one or two missed garments after the wash

has started, simply open the lid and this will pause the cycle.

After adding the garments, simply close the lid and the cycle

will resume. The washer may add some additional water to

offset the added garments.

If, instead, you press Start/Pause/Cancel to pause the cycle

and then open the lid to add garments, you will need to press

Start/Pause/Cancel after closing the lid to resume the cycle.

NOTE: Washer will not  ll with the lid open.

IMPORTANT: If lid is left open for more than 10 minutes, the

water will pump out automatically.

Manual soak

If you would like to manually soak your garments at any time

during the wash portion of the cycle, press START/PAUSE/

CANCEL and leave the lid closed. Once your desired soak

time has elapsed, press START/PAUSE/CANCEL again to

continue the cycle. As long as the lid remains closed, your

soak time can be longer than 10 minutes. However, if the lid

is opened during the soak and remains open for more than

10 minutes, the water will pump out automatically.

Appearance

may vary

Replace inlet hoses after 5 years of use to reduce the risk

of hose failure. Periodically inspect and replace inlet hoses

if bulges, kinks, cuts, wear, or leaks are found.

When replacing your inlet hoses, mark the date of replacement

on the label with a permanent marker.

NOTE: This washer does not include inlet hoses. See the

Installation Instructions for more information.

WATER INLET HOSES

Washer Maintenance

WASHER CARE

Recommendations to Help Keep Your Washer Clean

and Performing at its Best

1. Always use High Ef ciency (HE) detergents and follow

the detergent manufacturer’s instructions regarding the

amount of detergent to use. Never use more than the

recommended amount because that may increase the

rate at which detergent and soil residue accumulate inside

your washer, which in turn may result in undesirable odor.

2. Use warm and hot wash water settings sometimes (not

exclusively cold-water washes) because they do a better

job of controlling the rate at which soils and detergent

accumulate.

3. Always leave the washer lid open between uses to help

dry out the washer and prevent the buildup of odor-

causing residue.

Cleaning Your Top Loading Washer

Read these instructions completely before beginning the

routine cleaning processes recommended below. This washer

maintenance procedure should be performed, at a minimum,

once per month or every 30 wash cycles, whichever occurs

sooner, to control the rate at which soils and detergent may

otherwise accumulate in your washer.

Cleaning the Inside of the Washer

To keep your washer odor-free, follow the usage instructions

provided above and use this recommended monthly cleaning

procedure:

Clean Washer Cycle

This washer has a special cycle that uses higher water

volumes in combination with affresh

Washer Cleaner or

liquid chlorine bleach to clean the inside of the washer.

Begin procedure

1. affresh

Washer Cleaner Cycle Procedure

(Recommended for Best Performance):

a. Open the washer lid and remove any clothing or items.

b. Place an affresh

Washer Cleaner tablet in the bottom

of the washer basket.

c. Do not place an affresh

Washer Cleaner tablet in the

detergent dispenser.

d. Do not add any detergent or other chemical to the

washer when following this procedure.

e. Close the washer lid.

f. Select the cycle recommended for cleaning the inside

of the washer.

g. Press the START/PAUSE/CANCEL button to start

the cycle.

NOTE: For best results, do not interrupt cycle. If cycle

must be interrupted, press START/PAUSE/CANCEL once.

After the cycle has stopped, run a Rinse & Spin cycle to

rinse cleaner from washer.

Operate your washer only when you are home. If moving, or

not using your washer for a period of time, follow these steps:

1. Unplug or disconnect power to washer.

2. Turn off water supply to washer to avoid  ooding due

to water-pressure surge.

WINTER STORAGE CARE

IMPORTANT: To avoid damage, install and store washer

where it will not freeze. Some water may stay in hoses, and

freezing can damage washer. If storing or moving during

freezing weather, winterize your washer.

To winterize washer:

1. Shut off both water faucets; disconnect and drain water

inlet hoses.

2. Put 1 qt. (1 L) of R.V.-type antifreeze in basket and run

washer on Rinse & Spin cycle for about 30 seconds

to mix antifreeze and remaining water.

3. Unplug washer or disconnect power.

NON-USE AND VACATION CARE

TRANSPORTING YOUR WASHER

1. Shut off both water faucets. Disconnect and drain water

inlet hoses.

2. If washer will be moved during freezing weather, follow

“Winter Storage Care” directions before moving.

3. Disconnect drain hose from drain system and drain any

remaining water into a pan or bucket. Disconnect drain

hose from back of washer.

4. Unplug power cord.

5. Place inlet hoses and drain hose inside washer basket.

6. Drape power cord over edge and into washer basket.

7. Place packing tray from original shipping materials back

inside washer. If you do not have packing tray, place heavy

blankets or towels into basket opening. Close lid and place

tape over lid and down front of washer. Keep lid taped

until washer is placed in new location. Transport washer

in upright position.

WASHER CARE (cont.)

2. Chlorine Bleach Procedure (Alternative):

a. Open the washer lid and remove any clothing or items.

b. Add 1 cup (236 mL) of liquid chlorine bleach to the

bleach compartment.

NOTE: Use of more liquid chlorine bleach than is

recommended above could cause washer damage

over time.

c. Close the washer lid.

d. Do not add any detergent or other chemical

to the washer when following this procedure.

e. Select the cycle recommended for cleaning the inside

of the washer.

f. Press the START/PAUSE/CANCEL button to start

the cycle.

NOTE: For best results, do not interrupt cycle. If cycle

must be interrupted, press START/PAUSE/CANCEL once.

After the cycle has stopped, run a Rinse & Spin cycle to

rinse bleach from washer.

Description of Clean Washer Cycle Operation:

1. This cycle will  ll to a water level higher than in normal

wash cycles to provide rinsing at a level above the water

line for normal wash cycle.

2. During this cycle, there will be some agitation and

spinning to increase the removal of soils.

After this cycle is complete, leave the lid open to allow for

better ventilation and drying of the washer interior.

Cleaning the Dispensers

After a period of using your washer, you may  nd some

residue buildup in the washer’s dispensers. To remove

residue from the dispensers, wipe them with an affresh

Machine Cleaning Wipe or a damp cloth and towel dry either

before or after you run the Clean Washer cycle. Do not

attempt to remove the dispensers or trim for cleaning. The

dispensers and trim are not removable. If your model has a

dispenser drawer, however, remove the drawer and clean it

before or after you run the Clean Washer cycle. Use an all-

purpose surface cleaner, if needed.

Cleaning the Outside of the Washer

Use an affresh

Machine Cleaning Wipe, a soft, damp cloth,

or a sponge to wipe away any spills. Use an affresh

Machine

Cleaning Wipe or only mild soaps or cleaners when cleaning

external washer surfaces.

IMPORTANT: To avoid damaging the washer’s  nish,

do not use abrasive products.

REINSTALLING/USING WASHER AGAIN

To reinstall washer after non-use, vacation, winter storage,

or moving:

1. Refer to Installation Instructions to locate, level, and

connect washer.

2. Before using again, run washer through the following

recommended procedure:

To use washer again:

1. Flush water pipes and hoses. Reconnect water inlet hoses.

Turn on both water faucets.

2. Plug in washer or reconnect power.

3. Run washer through Bulky/Sheets cycle to clean washer

and remove antifreeze if used. Use half the manufacturer’s

recommended amount of detergent for a medium-size load.

Troubleshooting

If you experience Possible Causes Solution

Vibration or Off-Balance

Check the following for

proper installation or

see “Using Your Washer”

section

Feet may not be in contact

with the  oor.

Front and rear feet must be in  rm contact with  oor, and

washer must be level to operate properly.

Washer may not be level. Check  oor for  exing or sagging. If  ooring is uneven, a 3/4"

(19 mm) piece of plywood under your washer will reduce sound.

See “Level the Washer” in Installation Instructions.

Load could be unbalanced. Load dry items in loose heaps evenly around basket wall.

Adding wet items to washer or adding more water to basket

could unbalance washer.

Wash smaller loads to reduce imbalance.

Do not tightly pack. Avoid washing single items.

Use Bulky/Sheets cycle for oversized, non-absorbent items

such as jackets and small comforters. See “Cycle Guide.”

See “Cycle Guide” and “Using Your Washer” in this Use and

Care Guide.

Noises

Clicking or metallic

noises

Objects caught in washer drain

system.

Empty pockets before washing. Loose items such as coins

could fall between basket and tub or may block pump.

It may be necessary to call for service to remove items.

It is normal to hear metal items on clothing such as snaps,

buckles, or zippers touch against the basket.

Gurgling or humming Washer may be draining water. It is normal to hear the pump making a continuous humming

sound with periodic gurgling or surging as  nal amounts of

water are removed during the Drain & Spin cycles.

Humming Load sensing may be occurring. You may hear the hum of the sensing spins after you have

started the washer. This is normal.

Whirring Basket deceleration may be

occurring.

You may hear the whirring sound of the basket decelerating.

This is normal.

First try the solutions suggested here or visit our website at www.whirlpool.com/owners

(in Canada www.whirlpool.ca/owners) for assistance and to possibly avoid a service call.

Troubleshooting

If you experience Possible Causes Solution

Water Leaks

Check the following

for proper installation:

Washer not level. Water may splash off basket if washer is not level. Check that

load is not unbalanced or tightly packed.

Fill hoses not attached tightly. Tighten ll hose connection.

Fill hose washers. Make sure all four ll hose at washers are properly seated.

Drain hose connection. Pull drain hose from washer cabinet and properly secure it

to drain pipe or laundry tub.

Do not place tape over drain opening.

Check household plumbing for leaks

or clogged sink or drain.

Water can back up out of a clogged sink or drain pipe. Check

all household plumbing for leaks (laundry tubs, drain pipe, water

pipes, and faucets).

Washer not loaded as recommended. Improper loading can cause basket to be out of alignment

and cause water to splash off tub. See “Using Your Washer”

for loading instructions.

Washer not performing as expected

Not enough water

in washer

Load not completely covered

in water.

This is normal operation for a high efciency washer. If the Water

Level knob is set to Auto Sensing, the load will not be completely

under water. The washer senses load sizes and adds correct

amount of water for optimal cleaning. Use Bulky/Sheets cycle

for higher water ll, or set Water Level knob to Deep Water Wash

setting. See “What’s Under the Lid” and “Cycle Guide” to match

your load with the best cycle.

IMPORTANT: Do not add more water to washer. Adding water

results in less effective cleaning.

Run Clean Washer with affresh

cycle to optimize the water level

and wash performance due to soil buildup in washer basket.

Washer won’t run

or ll, washer stops

working, or wash light

remains on (indicating

that the washer was

unable to ll

appropriately)

Check for proper water supply. Both hoses must be attached and have water owing to

inlet valve.

Both hot and cold water faucets must be turned on.

Check that inlet valve screens have not become clogged.

Check inlet hoses for any kinks, which can restrict water ow.

First try the solutions suggested here or visit our website at www.whirlpool.com/owners

(in Canada www.whirlpool.ca/owners) for assistance and to possibly avoid a service call.

Washer won’t run

or ll, washer stops

working, or wash light

remains on (indicating

that the washer was

unable to ll

appropriately) (cont.)

Check proper electrical supply. Plug power cord into a grounded 3 prong outlet.

Do not use an extension cord.

Ensure there is power to outlet.

Reset a tripped circuit breaker. Replace any blown fuses.

NOTE: If problems continue, contact an electrician.

Troubleshooting

If you experience Possible Causes Solution

Washer not performing as expected (cont.)

Washer won’t run

or ll, washer stops

working, or wash light

remains on (indicating

that the washer was

unable to ll

appropriately) (cont.)

Normal washer operation. Lid must be closed for washer to run.

Washer will pause during certain phases of cycle. Do not

interrupt cycle.

Washer may be tightly packed. Remove several items, rearrange load evenly in basket, and add

detergent. Close lid and press START/PAUSE/CANCEL.

Do not add more than one or two additional items after cycle

has started to avoid tightly packing or unbalancing.

Washer not draining/

spinning, loads are still

wet, or nal spin light

remains on (indicating

that the washer was

unable to pump out

water within 10 minutes)

Small items may have been caught

in pump or between basket and tub,

which can slow draining.

Empty pockets and use garment bags for small items.

Using a cycle with a low spin speed. Cycles with lower spin speeds remove less water than cycles

with high spin speeds. Use the recommended cycle/spin speed

for your garment. To remove extra water in the load, select

Drain & Spin. Load may need to be rearranged to allow even

distribution of the load in the basket.

The washer may be tightly packed

or unbalanced.

Tightly packed or unbalanced loads may not allow the washer

to spin correctly, leaving the load wetter than normal. Evenly

arrange the wet load for balanced spinning. Select the Drain &

Spin cycle to remove excess water. See “Using Your Washer”

for loading recommendations.

Check plumbing for correct drain

hose installation. Drain hose

extends into standpipe further

than 4.5" (114 mm).

Check drain hose for proper installation. Use drain hose form

and securely attach to drain pipe or tub. Do not tape over drain

opening. Lower drain hose if the end is higher than 96" (2.4 m)

above the oor. Remove any clogs from drain hose.

Too much detergent causing suds

to slow or stop draining and spinning.

Always measure and follow detergent directions for your load.

To remove extra suds, select Rinse & Spin. Do not add detergent.

Dry spots on load

after cycle

High speed spins extract more

moisture than traditional top-load

washers.

The high spin speeds combined with air ow during the nal

spin can cause items near the top of the load to develop dry

spots during the nal spin. This is normal.

Washer may be tightly packed. Use Bulky/Sheets cycle for higher water ll, or set Water Level

knob to Deep Water Wash setting. See “Cycle Guide” to match

your load with the best cycle.

Added extra garments to the load

after the sensing/ll phase.

Add only one or two additional garments after washer

has started.

Incorrect or wrong

wash or rinse

temperatures

Check for proper water supply. Make sure hot and cold inlet hoses are not reversed.

Both hoses must be attached to both washer and faucet

and have both hot and cold water owing to inlet valve.

Check that inlet valve screens are not clogged.

Remove any kinks in hoses.

Energy saving controlled

wash temperatures.

This washer uses cooler wash and rinse water temperatures

than your previous washer. This includes cooler hot and warm

washes.

Load not rinsed Check for proper water supply. Make sure hot and cold inlet hoses are not reversed.

Both hoses must be attached and have water owing to the

inlet valve.

Both hot and cold water faucets must be on.

Inlet valve screens on washer may be clogged.

Remove any kinks in the inlet hose.

Not using HE detergent or using too

much HE detergent.

The suds from too much detergent can keep washer from

operating correctly. Always measure detergent and follow

detergent directions based on load size and soil level.

Washer not loaded as recommended. The washer is less efcient at rinsing when load is tightly packed.

Load garments in loose heaps evenly around the basket wall.

Load with dry items only.

First try the solutions suggested here or visit our website at www.whirlpool.com/owners

(in Canada www.whirlpool.ca/owners) for assistance and to possibly avoid a service call.

Troubleshooting

If you experience Possible Causes Solution

Washer not performing as expected (cont.)

Load not rinsed (cont.) Washer not loaded as recommended

(cont.).

Use cycle designed for the fabrics being washed.

Add only one or two additional garments after washer

has started.

Use Bulky/Sheets cycle for higher water ll, or set Water Level

knob to Deep Water Wash setting. See “Cycle Guide” to match

your load with the best cycle.

Sand, pet hair, lint,

etc. on load after

washing

Heavy sand, pet hair, lint, and

detergent or bleach residues may

require additional rinsing.

Add an extra or deep water rinse to the selected cycle and/or

use Heavy cycle or Deep Water Wash option.

Load is tangling Washer not loaded as recommended. See “Using Your Washer” section.

Select a cycle with a slower wash action and spin speed;

however, items will be wetter than those using a higher-speed

spin.

Use Bulky/Sheets cycle for higher water ll, or set Water

Level knob to Deep Water Wash setting.

See the “Cycle Guide”

to match your load with the best cycle.

Load garments in loose heaps evenly around the basket wall.

Reduce tangling by mixing types of load items. Use the

recommended cycle for the type of garments being washed.

Not cleaning or

removing stains

Added more water to washer. Washer senses load size and adds correct amount of water.

This is normal and necessary for clothes to move. It is normal

for the wash load to be not completely covered in water. Added

water results in less effective cleaning.

Washer not loaded as recommended. Washer is less efcient at cleaning when load is tightly packed.

Load garments in loose heaps evenly around the basket wall.

Load with dry items only.

Add only one or two additional garments after washer

has started.

Adding detergent on top of load. Add detergent, Oxi products, and color-safe bleach to the

bottom of the basket before adding the load items.

Not using HE detergent or using too

much HE detergent.

The suds from regular detergent can keep washer from operating

correctly.

Use only HE detergent. Be sure to measure correctly.

Always measure detergent and follow manufacturer’s directions

based on load size and soil level.

Not using correct cycle for fabric type. Use a higher soil level cycle option (on some models) and

warmer wash temperature to improve cleaning.

Use Heavy cycle for tough cleaning. See the “Cycle Guide”

to match your load with the best cycle.

Not using dispensers.

Use dispensers to avoid chlorine bleach and fabric softener staining.

Load dispensers before starting a cycle.

Do not add products directly onto load.

Not washing like colors together. Wash like colors together and remove promptly after the cycle

is complete to avoid dye transfer.

Incorrect dispenser

operation

Clogged dispenser. Load dispensers before starting a cycle.

Use only liquid chlorine bleach in the bleach dispenser. Use only

fabric softener in the fabric softener dispenser.

Rinse Option knob not set for fabric

softener option.

Set Rinse Option knob to Auto with Extra Rinse, Deep Water

Rinse, or Deep Water with Extra Rinse when using fabric

softener dispenser.

First try the solutions suggested here or visit our website at www.whirlpool.com/owners

(in Canada www.whirlpool.ca/owners) for assistance and to possibly avoid a service call.

Troubleshooting

If you experience Possible Causes Solution

Washer not performing as expected (cont.)

Fabric damage Sharp items were in pockets during

wash cycle.

Empty pockets, zip zippers, and snap or hook fasteners before

washing to avoid snags and tears.

Strings and straps could have tangled.

Tie all strings and straps before starting wash load.

Items may have been damaged

before washing.

Mend rips and broken threads in seams before washing.

Fabric damage can occur if load is

tightly packed.

Load garments in loose heaps evenly around the basket wall.

Load with dry items only.

Use cycle designed for the fabrics being washed.

Use Bulky/Sheets cycle for higher water ll, or set Water Level

knob to Deep Water Wash setting. See “What’s Under the Lid”

and “Cycle Guide” to match your load with the best cycle.

Add only one or two additional garments after washer

has started.

Liquid chlorine bleach may have

been added incorrectly.

Do not pour liquid chlorine bleach directly onto load. Wipe up

bleach spills.

Undiluted bleach will damage fabrics. Do not use more than

recommended by manufacturer.

Do not place load items on top of bleach dispenser when

loading and unloading washer.

Garment care instructions may not

have been followed.

Always read and follow garment manufacturer’s care label

instructions. See the “Cycle Guide” to match your load with

the best cycle.

Odors Monthly maintenance not done

as recommended.

See “Washer Care” in “Washer Maintenance.”

Unload washer as soon as cycle is complete.

Using too much detergent. Be sure to measure correctly. Always follow the manufacturer’s

directions.

See “Washer Care” section.

Lid Locked light

is ashing

The lid is not closed. Close the lid. The washer will not start with the lid open.

A cycle was stopped or paused

using the Start/Pause/Cancel button.

The washer may still be spinning. The lid will not unlock until the

basket has stopped spinning. This may take several minutes if

washing large loads or heavy fabrics.

Single-dose laundry

packet not dissolving

Adding laundry packet incorrectly. Be sure laundry packet is added to washer basket before

adding clothes. Do not add packet to dispenser. Follow the

manufacturer’s instructions to avoid damage to your garments.

Washer pumps out water

before nishing cycle

Lid is left open for more than

10 minutes.

Make sure lid is closed before starting a cycle and/or during

prewash (soak).

First try the solutions suggested here or visit our website at www.whirlpool.com/owners

(in Canada www.whirlpool.ca/owners) for assistance and to possibly avoid a service call.

WHIRLPOOL

LAUNDRY

LIMITED WARRANTY

ATTACH YOUR RECEIPT HERE. PROOF OF PURCHASE IS

REQUIRED TO OBTAIN WARRANTY SERVICE.

Please have the following information available when you call the

Customer eXperience Center:

Name, address, and telephone number

Model number and serial number

A clear, detailed description of the problem

Proof of purchase including dealer or retailer name and address

DISCLAIMER OF IMPLIED WARRANTIES

IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR IMPLIED WARRANTY OF FITNESS FOR

A PARTICULAR PURPOSE, ARE LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW. Some states and provinces

do not allow limitations on the duration of implied warranties of merchantability or tness, so this limitation may not apply to you. This

warranty gives you specic legal rights, and you also may have other rights that vary from state to state or province to province.

LIMITATION OF REMEDIES; EXCLUSION OF INCIDENTAL AND CONSEQUENTIAL DAMAGES

YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED HEREIN.

WHIRLPOOL SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some states and provinces do not allow

the exclusion or limitation of incidental or consequential damages, so these limitations and exclusions may not apply to you. This

warranty gives you specic legal rights, and you also may have other rights that vary from state to state or province to province.

DISCLAIMER OF REPRESENTATIONS OUTSIDE OF WARRANTY

Whirlpool makes no representations about the quality, durability, or need for service or repair of this major appliance other than the

representations contained in this Warranty. If you want a longer or more comprehensive warranty than the limited warranty that comes

with this major appliance, you should ask Whirlpool or your retailer about buying an extended warranty.

10/17

IF YOU NEED SERVICE:

1. Before contacting us to arrange service, please determine whether your product requires repair. Some questions can be

addressed without service. Please take a few minutes to review the Troubleshooting section of the Use and Care Guide

or visit the “HOW-TOS & FAQS” section of https://www.whirlpool.com/owners.html.

2. All warranty service is provided exclusively by our authorized Whirlpool Service Providers.

In the U.S. and Canada, direct all requests for warranty service to:

Whirlpool Customer eXperience Center

In the U.S.A. call 1-866-698-2538. In Canada call 1-800-807-6777.

If outside the 50 United States and Canada, contact your authorized Whirlpool dealer to determine if another warranty applies.

ONE YEAR LIMITED WARRANTY

WHAT IS COVERED

WHAT IS NOT COVERED

1. Commercial, non-residential, multiple-family use, or use inconsistent with published

user, operator, or installation instructions.

2. In-home instruction on how to use your product.

3. Service to correct improper product maintenance or installation, installation not in

accordance with electrical or plumbing codes, or correction of household electrical

or plumbing (e.g., house wiring, fuses, or water inlet hoses).

4. Consumable parts (e.g., light bulbs, batteries, air or water lters, preservation

solutions).

Defects or damage caused by the use of non-genuine Whirlpool parts or accessories.

6. Conversion of your product from natural gas or propane gas or reversal

of appliance doors.

7. Damage from accident, misuse, abuse, re, oods, acts of God, or use with

products not approved by Whirlpool.

8. Repairs to parts or systems to correct product damage or defects caused by

unauthorized service, alteration, or modication of the appliance.

9. Cosmetic damage including scratches, dents, chips, and other damage to appliance

nishes unless such damage results from defects in materials and workmanship and

is reported to Whirlpool within 30 days.

10. Discoloration, rust, or oxidation of surfaces resulting from caustic or corrosive

environments, including but not limited to, high salt concentrations, high moisture

or humidity, or exposure to chemicals.

11. Pick-up or delivery. This product is intended for in-home repair.

12. Travel or transportation expenses for service in remote locations where an

authorized Whirlpool servicer is not available.

13. Removal or reinstallation of inaccessible appliances or built-in xtures (e.g., trim,

decorative panels, ooring, cabinetry, islands, countertops, drywall) that interfere

with servicing, removal, or replacement of the product.

14. Service or parts for appliances with original model/serial numbers removed, altered,

or not easily determined.

The cost of repair or replacement under these excluded circumstances shall be

borne by the customer.

For one year from the date of purchase,

when this major appliance is installed,

operated, and maintained according

to instructions attached to or furnished

with the product, Whirlpool Corporation

or Whirlpool Canada LP (hereafter

“Whirlpool”) will pay for Factory

Specified Replacement Parts and repair

labor to correct defects in materials or

workmanship that existed when this major

appliance was purchased, or at its sole

discretion replace the product. In the event

of product replacement, your appliance

will be warranted by the remaining term of

the original unit’s warranty period.

YOUR SOLE AND EXCLUSIVE REMEDY

UNDER THIS LIMITED WARRANTY

SHALL BE PRODUCT REPAIR AS

PROVIDED HEREIN. Service must be

provided by a Whirlpool designated

service company. This limited warranty

is valid only in the United States or

Canada and applies only when the major

appliance is used in the country in which

it was purchased. This limited warranty

is effective from the date of original

consumer purchase. Proof of original

purchase date is required to obtain service

under this limited warranty.

Sécurité de la laveuse

Ce qui est sous le couvercle

Utiliser uniquement un détergent haute efcacité (HE).

IMPORTANT :

■ Le couvercle doit être fermé avant que le panier de la laveuse se remplisse et que le programme de lavage se mette en marche.

Si le couvercle est ouvert, le programme s’arrête et tous les mouvements de remplissage/agitation s’arrêtent. Une fois le couvercle

fermé, le programme reprend automatiquement. Toutefois, si le bouton Start/Pause/Cancel (mise en marche/pause/annulation) est

pressé avant d’ouvrir le couvercle, il faut fermer le couvercle et appuyer de nouveau sur le bouton Start/Pause/Cancel (mise en

marche/pause/annulation) pour reprendre le programme.

■ Option de rinçage doit être réglée sur Auto with Extra Rinse (auto avec rinçage supplémentaire), Deep Water Rinse (rinçage

à l’eau profonde) ou Deep Water with Extra Rinse (rinçage à l’eau profonde avec rinçage supplémentaire) lors de l’utilisation

d’assouplissant pour tissu dans le distributeur d’assouplissant pour tissu. Cela garantit que l’assouplissant pour tissu est

ajouté au bon moment dans la phase de rinçage et est uniformément répartie.

Verrouillage du couvercle

Pour permettre des essorages à vitesse plus élevée, le

couvercle se verrouille et le témoin de Lid Locked (couvercle

verrouillé) s’allume. Lorsque ce témoin lumineux s’allume, cela

signie que le couvercle est verrouillé et ne peut être ouvert

sans suspendre le programme. Lorsque ce témoin lumineux

clignote, cela signie que la laveuse effectue une pause.

Lorsque ce témoin lumineux est éteint, cela signie qu’on peut

ouvrir le couvercle. Une fois qu’un programme a commencé,

la laveuse se remplit au niveau d’eau approprié. Sur certains

programmes, l’agitation se produit pendant que le panier se

remplit d’eau. Ceci est normal. Quand la laveuse est faite

remplir, l’étape de lavage va commencer. Si l’on doit ouvrir

le couvercle pour ajouter un vêtement après cette étape, le

couvercle de la demeurera déverrouillé pendant toute la partie

de l’agitation de l’étape de lavage. Le programme fait une

pause automatiquement quand le couvercle est ouvert, et le

programme recommencera après la fermeture du couvercle.

Le couvercle se verrouille avant le début de l’étape d’essorage.

Si l’on doit pauser ou arrêter après cette étape, il faut appuyer

sur START/PAUSE/CANCEL (mise en marche/pause/annulation)

puis attendre que le couvercle se déverrouille. Le couvercle

se déverrouille uniquement une fois que le mouvement de la

laveuse a cessé. Selon le moment où l’on souhaite suspendre

le programme, le couvercle peut mettre entre quelques

secondes et plusieurs minutes à se déverrouiller. Appuyer sur

START/PAUSE/CANCEL (mise en marche/pause/annulation)

pour poursuivre le programme.

Détection

Cette laveuse détecte automatiquement la taille de la charge

pour la plupart des programmes, et sélectionne un niveau

d’eau approprié en fonction de la taille de la charge détectée.

Cette laveuse effectue également une série d’essorages pour

contrôler l’équilibre de la charge. Durant cette période, une série

de cliquetis et un bruit de frottements rythmiques indiquent

que la technologie de détection détermine si la charge est

déséquilibrée.

Options de niveau d’eau

Régler le bouton Water Level (niveau d’eau) sur le réglage

Auto Sensing (détection automatique) et la laveuse ajuste

automatiquement le niveau d’eau en fonction de la taille de

la charge. Régler le bouton Water Level (niveau d’eau) sur

le réglage Deep Water Wash (lavage à l’eau profonde) et la

laveuse ajoute automatiquement plus d’eau à n’importe quel

programme à tout moment pendant le processus de lavage.

Sons normaux prévisibles

Au cours des différents stades du programme de lavage, vous

entendrez peut-être des bruits que votre laveuse précédente

ne produisait pas. Par exemple, vous entendrez peut-être un

cliquetis au début de l’étape d’essorage lorsque le système

de verrouillage du couvercle effectue un test automatique.

Différents bourdonnements et bruits de frottements rythmiques

se produiront à mesure que l’agitateur HE évalue l’équilibre

de la charge et qu’il la déplace. Parfois, il est possible que la

laveuse soit complètement silencieuse, lorsqu’elle détermine le

niveau d’eau adéquat ou qu’elle laisse tremper les vêtements.

Rinçage par vaporisation

Certains programmes utilisent l’option rinçage par

vaporisation par défaut. Au cours de ces programmes,

on entend l’eau pénétrer dans la laveuse tandis que la cuve

tourne, ce qui permet à l’eau de rinçage de pénétrer les

vêtements. Consulter le “Guide des programmes” pour

plus de détails.

Choix du détergent approprié

Utiliser uniquement des détergents haute efcacité. L’emballage

portera la mention “HE” ou “High Efciency” (haute efcacité).

Il est probable que l’utilisation d’un détergent non HE

prolongera la durée des programmes et réduira la performance

de rinçage. Ceci peut aussi entraîner des malfunctions de

composants et, avec le temps, une accumulation de moisissure.

Les détergents HE devraient produire peu de mousse et se

dissoudre rapidement pour produire une quantité de mousse

idéale pour une performance optimale. Ils devraient retenir

les particules de saleté en suspension an qu’elles ne se

redéposent pas sur les vêtements propres. Les détergents

identiés HE ne comportent pas tous une formule identique

et ne produisent pas tous la même quantité de mousse. Par

exemple, les détergents HE naturels, organiques et faits maison

peuvent produire une plus grande quantité de mousse. Toujours

suivre les instructions du fabricant pour déterminer la quantité

de détergent à utiliser.

La page charge ...

Whirlpool WTW4955HW Mode d'emploi

Marque: Whirlpool

Modèle: WTW4955HW

Catégorie: Machines à laver

Taper: Mode d'emploi

Télécharger le PDF

rapport

dans d''autres langues

English: Whirlpool WTW4955HW User guide

Whirlpool WTW4955HW Mode d'emploi

Whirlpool WTW4955HW Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents