Whirlpool WTW4955HW Mode d'emploi

Catégorie
Machines à laver
Taper
Mode d'emploi
W11035364A
W11035698A-SP
Top-Loading
High Efficiency Washer
Use and Care Guide
Table of Contents
WASHER SAFETY ...................................................................... 2
WHAT’S UNDER THE LID .......................................................... 3
CONTROL PANEL AND FEATURES ......................................... 4
CYCLE GUIDE ............................................................................ 6
USING YOUR WASHER ............................................................. 8
WASHER MAINTENANCE ....................................................... 11
TROUBLESHOOTING .............................................................. 13
WARRANTY .............................................................................. 18
ASSISTANCE OR SERVICE ..................................BACK COVER
Table des matières
SÉCURITÉ DE LA LAVEUSE ................................................... 19
CE QUI EST SOUS LE COUVERCLE ...................................... 20
TABLEAU DE COMMANDE
ET CARACTÉRISTIQUES ........................................................ 21
GUIDE DES PROGRAMMES ................................................... 23
UTILISATION DE LA LAVEUSE ............................................... 25
ENTRETIEN DE LA LAVEUSE ................................................. 28
DÉPANNAGE ............................................................................ 30
GARANTIE ................................................................................ 37
ASSISTANCE OU SERVICE ............... COUVERTURE ARRIÈRE
Guide d’utilisation
et d’entretien de la laveuse
haute efficacité avec
chargement par le dessus
Para una versión de estas instrucciones en español, visite www.whirlpool.com
Designed to use only HE
(High Efciency) detergents.
Conçue pour l’utilisation d’un détergent
haute efcacité seulement.
2
Washer Safety
3
What’s Under the Lid
Use only High Efciency (HE) detergent.
IMPORTANT:
The lid must be closed before the washer basket lls with water and for the wash cycle to start. If the lid is opened, the cycle
pauses and all lling/agitation motion halts. Once the lid is closed, the cycle automatically resumes. However, if the Start/Pause/
Cancel button is pressed prior to opening the lid, the lid must be closed and the Start/Pause/Cancel button pressed again to
resume the cycle.
Rinse option must be set to Auto with Extra Rinse, Deep Water Rinse, or Deep Water with Extra Rinse when using fabric softener
in the fabric softener dispenser. This ensures that fabric softener is added at the correct time in the rinse phase and is evenly
distributed.
Lid Lock
To allow for higher spin speeds, the lid will lock and the Lid
Locked light will turn on. When this light is lit, the lid is locked
and cannot be opened without pausing the cycle. When this
light is blinking, the washer is paused. When this light is off,
the lid can be opened. After the cycle has started, the washer
will ll to the appropriate water level. On select cycles, agitation
will occur while the basket is lling with water. This is normal.
When the washer is done lling, it will begin the wash phase.
If you need to open the lid to add a garment after this point, the
lid will remain unlocked during the entire agitation portion of the
wash phase. The cycle will automatically pause when the lid is
opened, and the cycle will resume once the lid is closed. The
lid will lock before the spin phase begins. If you need to pause
or stop after this point, you must press the START/PAUSE/
CANCEL button and wait for the lid to unlock. The lid will only
unlock after washer movement has stopped. Depending on
when in the cycle you try to pause, it may take from several
seconds to several minutes for the lid to unlock. Press START/
PAUSE/CANCEL to resume the cycle.
Sensing
This washer automatically senses the load size for most cycles,
and chooses an appropriate water level according to the load
size detected. This washer also performs a series of spins to
check for load balance. During this time, a series of clicks and
a whirring noise signal that sensing technology is determining
if there is an off-balance load.
Water Level Options
Set the Water Level knob to the Auto Sensing setting and the
washer automatically adjusts the water level to the load size.
Set the Water Level knob to the Deep Water Wash setting and
the washer automatically adds more water to any cycle at any
time during the wash process.
Normal Sounds You Can Expect
At different stages of the wash cycle, you may hear sounds
and noises that are different from those of your previous washer.
For example, you may hear a clicking and hum at the beginning
of the spin phase, as the lid lock goes through a self-test. There
will be different kinds of humming sounds as the HE agitator
tests for load balance or moves the load. And sometimes, you
may hear nothing at all, as the washer determines the correct
water level for your load or allows time for clothes to soak.
Spray Rinse
Select cycles default to a spray rinse. During these cycles,
you will hear water enter the washer as the tub spins, allowing
the rinse water to penetrate clothes. Check the “Cycle Guide”
for details.
Choosing the Right Detergent
Use only High Efciency detergents. The package will be
marked “HE” or “High Efciency.” Using non-HE detergent
will likely result in longer cycle times and reduced rinsing
performance. It may also result in component malfunction and,
over time, buildup of mold or mildew. HE detergents should be
low-sudsing and quick-dispersing to produce the right amount
of suds for the best performance. They should hold soil in
suspension so it is not redeposited onto clean clothes. Not all
detergents labeled as High Efciency are identical in formulation
and their ability to reduce suds. For example, natural, organic,
or homemade HE detergents may generate a high level of suds.
Always follow the detergent manufacturer’s instructions to
determine the amount of detergent to use.
4
7
1
6
Control Panel and Features
SOIL LEVEL (on some models)
Select the setting most suitable for your load. For heavily
soiled and sturdy fabrics, select Heavy soil level for more
wash time. For lightly soiled and delicate fabrics, select Light
or Extra Light soil level for less wash time. A lighter soil level
setting will help reduce tangling and wrinkling.
WASH TEMP or WASH TEMPERATURE
Wash Temp senses and maintains uniform water
temperatures by regulating incoming hot and cold water.
Select a wash temperature based on the type of fabric
and soils being washed. For best results, use the warmest
wash water safe for your fabric, as speci ed by the garment
label instructions.
On some models and cycles, warm and hot water may
be cooler than your previous washer.
Even in a cold- and cool-water wash, some warm water
may be added to the washer to maintain a minimum
temperature.
All rinses are cold.
WASH CYCLE KNOB
Use the Wash Cycle knob to select cycles on your washer.
See “Cycle Guide” for detailed descriptions of cycles.
1
2
3
RINSE OPTION
Select the option most suitable for your load. Select Auto
with Extra Rinse, Deep Water Rinse, or Deep Water with
Extra Rinse if using fabric softener during a cycle. It ensures
that fabric softener is added at the correct time in the rinse
for even distribution.
WATER LEVEL
Set the Water Level knob to the Auto Sensing setting and the
washer will automatically sense the appropriate water level
for the load size and type.
Set the Water Level knob to the Deep Water Wash setting
and the washer will automatically add more water to any
cycle at any time during the wash process.
NOTE: Expect longer cycle times due to extended  ll times
when using the Deep Water Wash option.
START/PAUSE/CANCEL BUTTON
Press to start the selected cycle. Press again to pause the
cycle and unlock the lid. Close the lid and press to restart
the cycle. Press and hold to cancel a cycle and pump out
the washer.
NOTE: If the washer is spinning, it may take several minutes
to unlock the lid.
5
6
Not all features and options are available on all models.
Appearance may vary.
432
7
6
452
5
4
3
5
PROGRESS LIGHTS
The Progress Lights show the progress of a cycle. At each
stage of the process, you may notice sounds or pauses
that are different from traditional washers.
SENSING/FILL
When the Start/Pause/Cancel button is pressed
and the Water Level knob is set to Auto Sensing, the
washer will ll and begin sensing to determine load
size and balance. A short but noticeable pause in the
cycle action occurs during sensing. This is normal.
Once sensing is complete, the washer will ll to the
appropriate level for the detected load size and, on
select cycles, agitation will occur during lling. This,
too, is normal. When the washer is done lling, it will
begin the wash phase of the cycle. To ensure that
the most accurate load size is detected, avoid opening
the lid during the “Sensing” phase.
NOTE: Sensing and wash phases will be paused by
opening the unlocked lid. Close the lid to resume the
cycle. If the lid is left open for more than 10 minutes,
the washer will cancel the cycle and pump out the
water.
WASH
The washer will ll to the correct water level based
on the load size and the Water Level selection. Certain
cycles may agitate during the ll process to boost
cleaning. When the wash cycle begins, you will hear
the HE agitator increase speed. The motor sounds may
change at different stages in the wash cycle while the
washer performs different wash actions.
NOTE: The lid will automatically lock after the wash
phase completes and before the initial spinout occurs,
and will remain locked for the rest of the cycle.
RINSE
Certain cycles use a spray rinse, which adds water
to the tub while the basket spins. You may hear the
motor turning on briey (short hum) to move the basket
while lling. In some cases, you may also hear sounds
similar to the wash cycle as the washer lls, rinses,
and moves the load.
FINAL SPIN
The washer spins the load at increasing speeds for
proper water removal based on the selected cycle
and spin speed.
CYCLE COMPLETE
Once the cycle is complete, the lid will unlock and this
light will come on. For best results, remove the load
promptly.
LID LOCKED
The Lock feature allows for higher spin
speeds. When lit, the lid is locked and
cannot be opened without pausing the
cycle. When the light is off, the lid can
be opened.
To open the lid after it has been
locked, press START/PAUSE/
CANCEL. The lid will unlock once the
washer movement has stopped. This
may take several minutes if the load
was spinning at high speed. Press
START/PAUSE/CANCEL while the lid
is closed to resume the cycle.
7
Appearance
may vary
6
Cycle Guide
For best fabric care, choose the cycle that best ts the load being washed. Recommended settings for best performance are shown
in Bold. Not all cycles and options are available on all models.
Sturdy fabrics,
colorfast items,
towels, jeans
Heavy Hot
Warm
Cool
Cold
Tap Cold
High Use this cycle for heavily soiled or sturdy items. Water-level
sensing process may take longer for some items than for
others because they will absorb more water than other
fabric types.
Heavily soiled
white fabrics
Whites
Whites
with Soak
Hot
Warm
Cool
Cold
Tap Cold
High This cycle, when used with chlorine bleach, improves
whitening of soiled white fabrics.
To enhance cleaning, select Whites with Soak, which
automatically adds about 10 minutes of soak time after the
ll phase, and then automatically runs the Whites cycle.
Large items such
as sheets, sleeping
bags, small
comforters, jackets,
small, washable
rugs
Bulky/Sheets Hot
Warm
Cool
Cold
Tap Cold
Low Use this cycle to wash large items such as jackets and small
comforters. The washer will ll with enough water to wet
down the load before the wash portion of the cycle begins
and uses a higher water level than other cycles.
Cottons, linens,
and mixed loads
Normal Hot
Warm
Cool
Cold
Tap Cold
High Use this cycle for normally soiled cottons and mixed loads.
Bright and darkly
colored cottons
and mixed loads
Colors
Colors
with Soak
§
Hot
Warm
Cool
Cold
Tap Cold
High Use this cycle to wash darks and colors, including mixed
loads and activewear.
§
To enhance cleaning, select Colors with Soak, which
automatically adds about 10 minutes of soak time after the
ll phase, and then automatically runs the Colors cycle.
Machine-wash silks,
handwash fabrics
Delicates Hot
Warm
Cool
Cold
Tap Cold
Low Use this cycle to wash lightly soiled items indicating
“Machine Washable Silks” or “Gentle” cycle on the care
label. Place small items in mesh garment bags before
washing. This cycle uses a higher, preset water level.
Items to wash: Cycle: Wash Temp:* Spin
Speed:**
Cycle Details:
Cleaning
Gentleness
Efciency
Good
Best
Cleaning
Gentleness
Efciency
Good
Best
Cleaning
Gentleness
Efciency
Good
Best
Cleaning
Gentleness
Efciency
Good
Best
Cleaning
Gentleness
Efciency
Good
Best
Cleaning
Gentleness
Efciency
Good
Best
NOTE: If you are using fabric softener, be sure to select one of the following Rinse Option settings: Auto with Extra Rinse, Deep Water
Rinse, or Deep Water with Extra Rinse.
**All rinses are cold.
**Spin speed is integrated into the cycle and cannot be selected or modied.
*
Efcient use of resources, such as energy and water.
7
Small loads,
cottons, polyester,
permanent press
Quick Wash Hot
Warm
Cool
Cold
Tap Cold
High Use this cycle to wash small, lightly soiled loads of two or
three items that are needed in a hurry.
Swimsuits and
items requiring
rinsing without
detergent
Rinse &
Spin
Cold rinse only High Combines a rinse and high-speed spin for loads requiring
an additional rinse cycle. Use this cycle to complete a load
after power interruption or for loads that require rinsing only.
Hand-washed items
or dripping-wet
items
Drain &
Spin
N/A High This cycle uses a spin to shorten drying times for heavy
fabrics or special-care items washed by hand. Use this
cycle to drain washer after canceling a cycle or completing
a cycle after a power failure.
No clothes
in washer
Clean Washer
with affresh
®
Hot Low Use this cycle every 30 washes to keep the inside of your
washer fresh and clean. This cycle uses a higher water level.
Use with affresh
®
Washer Cleaner tablet or liquid chlorine
bleach to thoroughly clean the inside of your washer. This
cycle should not be interrupted. See “Washer Care.”
IMPORTANT: Do not place garments or other items in the
washer during the Clean Washer with affresh
®
cycle. Use
this cycle with an empty wash tub.
Items to wash: Cycle: Wash Temp:* Spin
Speed:**
Cycle Details:
Cleaning
Gentleness
Efciency
Good
Best
NOTE: If you are using fabric softener, be sure to select one of the following Rinse Option settings: Auto with Extra Rinse, Deep Water
Rinse, or Deep Water with Extra Rinse.
**All rinses are cold.
**Spin speed is integrated into the cycle and cannot be selected or modied.
*
Efcient use of resources, such as energy and water.
8
Empty pockets. Loose change, buttons, or any small
object can pass under the HE agitator and become
trapped, causing unexpected sounds.
Sort items by recommended cycle, water temperature,
and colorfastness.
Separate heavily soiled items from lightly soiled.
Separate delicate items from sturdy fabrics.
Do not dry garments if stains remain after washing
because heat can set stains into fabric.
Treat stains promptly.
Close zippers, fasten hooks, tie strings and sashes,
and remove non-washable trim and ornaments.
Mend rips and tears to avoid further damage to items
during washing.
Helpful Tips:
When washing water-proof or water-resistant items,
load evenly.
Use mesh garment bags to help avoid tangling when
washing delicate or small items.
Turn knits inside out to avoid pilling. Separate lint-takers
from lint-givers. Synthetics, knits, and corduroy fabrics will
pick up lint from towels, rugs, and chenille fabrics.
NOTE: Always read and follow fabric care label instructions
to avoid damage to your items.
1. Sort and prepare your laundry
Add a measured amount of HE
detergent or single-dose laundry
packet into the basket.
If using Oxi-type boosters, color-safe
bleach, or fabric-softener crystals, add
to the bottom of the washer basket before adding clothes.
IMPORTANT: Use only High Ef ciency detergents. The
package will be marked “HE” or “High Ef ciency.” Using
regular detergent will likely result in longer cycle times
and reduced rinsing performance. It may also result in
component failures and noticeable mold or mildew. HE
detergents are made to produce the right amount of suds
for the best performance.
NOTE: Follow the manufacturer’s instructions to determine
the amount of laundry products to use.
2. Add laundry products
Using Your Washer
9
5. Add fabric softener to dispenser
Pour a measured amount of liquid fabric
softener into dispenser; always follow
manufacturer’s directions for correct amount
of fabric softener based on your load size.
Dilute liquid fabric softener by  lling the dispenser with warm
water until liquid reaches the underside of the rim. See Max Fill
line arrows.
IMPORTANT: The Rinse Option knob must be set to Auto with
Extra Rinse, Deep Water Rinse, or Deep Water with Extra Rinse
when using fabric softener in the fabric softener dispenser. This
ensures that fabric softener is added at the correct time in the
rinse phase and is evenly distributed.
Adding Liquid Fabric Softener Manually
to Wash Load
During the  nal rinse, wait until the washer has completed
lling and press the START/PAUSE/CANCEL button to pause
the washer. Lift the lid and add the measured, recommended
amount of liquid fabric softener. Do not use more than the
recommended amount. Close the lid and press the START/
PAUSE/CANCEL button again to start the washer.
Liquid
Chlorine Bleach
4. Add liquid chlorine bleach
to dispenser
Do not over ll, dilute, or use more than 1 cup (236 mL).
Do not use color-safe bleach or Oxi products in the same
cycle with liquid chlorine bleach.
Load garments in loose heaps evenly
around basket wall. For best results, do
not pack the load tightly. Do not wrap
large items such as sheets around the
HE agitator; load them in loose piles
around the sides of the basket. Try
mixing different-sized items to reduce
tangling.
IMPORTANT: Do not tightly pack or
force items into washer. Items need to move freely for best
cleaning and to reduce wrinkling and tangling.
3. Load laundry into washer
MAX FILL
Turn cycle knob to choose your wash cycle. For more
information, see “Cycle Guide.”
6. Select cycle
Appearance may vary
Fabric softener
Water
10
Wash Temp Suggested Fabrics
8. Select wash temp
or wash temperature
Once you select a cycle, select the wash temperature by
turning the Wash Temp or Wash Temperature knob to the
desired setting.
Always read and follow fabric care label instructions
to avoid damage to your items.
9. Select rinse option and water level
Select the number of rinses by turning the Rinse Option
knob to the desired setting.
IMPORTANT: The Rinse Option knob must be set to Auto
with Extra Rinse, Deep Water Rinse, or Deep Water with
Extra Rinse when using the fabric softener dispenser. This
ensures that fabric softener is added at the correct time in
the rinse for even distribution.
Set the Water Level knob to the Auto Sensing setting and
the washer will automatically sense the appropriate water
level for the load size and type.
Set the Water Level knob to the Deep Water Wash setting
and the washer will automatically add more water to any
cycle at any time during the wash cycle.
NOTE: The cycle will be longer due to extended  ll times
when using the Deep Water Wash setting.
Cool
Warm water is added to assist in
soil removal and to help dissolve
detergents. Cool is slightly warmer
than cold.
Dark colors that
bleed or fade
Light soils
Hot
Some cold water is added to save
energy. This may be cooler than
your hot water heater setting.
Warm
Some cold water will be added, so
this may be cooler than what your
previous washer provided.
Cold
Warm water may be added to
assist in soil removal and to help
dissolve detergents.
Whites and pastels
Durable items
Heavy soils
Bright colors
Moderate to light soils
Colors that bleed
or fade
Light soils
Dark colors that
bleed or fade
Light soils
Tap Cold
This is the temperature
from your faucet.
7. Select soil level (on some models)
Once you select a cycle, select the soil level by turning the
Soil Level knob to the desired setting.
or
or
11
10. Press START/PAUSE/CANCEL
to begin wash cycle
Press START/PAUSE/CANCEL to start the wash cycle. When
the cycle has  nished, the Cycle Complete progress light will
light. Promptly remove garments after cycle has completed
to avoid odor, reduce wrinkling, and avoid rusting of metal
hooks, zippers, and snaps.
Unlocking the lid to add garments
If you need to add one or two missed garments after the wash
has started, simply open the lid and this will pause the cycle.
After adding the garments, simply close the lid and the cycle
will resume. The washer may add some additional water to
offset the added garments.
If, instead, you press Start/Pause/Cancel to pause the cycle
and then open the lid to add garments, you will need to press
Start/Pause/Cancel after closing the lid to resume the cycle.
NOTE: Washer will not  ll with the lid open.
IMPORTANT: If lid is left open for more than 10 minutes, the
water will pump out automatically.
Manual soak
If you would like to manually soak your garments at any time
during the wash portion of the cycle, press START/PAUSE/
CANCEL and leave the lid closed. Once your desired soak
time has elapsed, press START/PAUSE/CANCEL again to
continue the cycle. As long as the lid remains closed, your
soak time can be longer than 10 minutes. However, if the lid
is opened during the soak and remains open for more than
10 minutes, the water will pump out automatically.
Appearance
may vary
Replace inlet hoses after 5 years of use to reduce the risk
of hose failure. Periodically inspect and replace inlet hoses
if bulges, kinks, cuts, wear, or leaks are found.
When replacing your inlet hoses, mark the date of replacement
on the label with a permanent marker.
NOTE: This washer does not include inlet hoses. See the
Installation Instructions for more information.
WATER INLET HOSES
Washer Maintenance
WASHER CARE
Recommendations to Help Keep Your Washer Clean
and Performing at its Best
1. Always use High Ef ciency (HE) detergents and follow
the detergent manufacturer’s instructions regarding the
amount of detergent to use. Never use more than the
recommended amount because that may increase the
rate at which detergent and soil residue accumulate inside
your washer, which in turn may result in undesirable odor.
2. Use warm and hot wash water settings sometimes (not
exclusively cold-water washes) because they do a better
job of controlling the rate at which soils and detergent
accumulate.
3. Always leave the washer lid open between uses to help
dry out the washer and prevent the buildup of odor-
causing residue.
Cleaning Your Top Loading Washer
Read these instructions completely before beginning the
routine cleaning processes recommended below. This washer
maintenance procedure should be performed, at a minimum,
once per month or every 30 wash cycles, whichever occurs
sooner, to control the rate at which soils and detergent may
otherwise accumulate in your washer.
Cleaning the Inside of the Washer
To keep your washer odor-free, follow the usage instructions
provided above and use this recommended monthly cleaning
procedure:
Clean Washer Cycle
This washer has a special cycle that uses higher water
volumes in combination with affresh
®
Washer Cleaner or
liquid chlorine bleach to clean the inside of the washer.
Begin procedure
1. affresh
®
Washer Cleaner Cycle Procedure
(Recommended for Best Performance):
a. Open the washer lid and remove any clothing or items.
b. Place an affresh
®
Washer Cleaner tablet in the bottom
of the washer basket.
c. Do not place an affresh
®
Washer Cleaner tablet in the
detergent dispenser.
d. Do not add any detergent or other chemical to the
washer when following this procedure.
e. Close the washer lid.
f. Select the cycle recommended for cleaning the inside
of the washer.
g. Press the START/PAUSE/CANCEL button to start
the cycle.
NOTE: For best results, do not interrupt cycle. If cycle
must be interrupted, press START/PAUSE/CANCEL once.
After the cycle has stopped, run a Rinse & Spin cycle to
rinse cleaner from washer.
12
Operate your washer only when you are home. If moving, or
not using your washer for a period of time, follow these steps:
1. Unplug or disconnect power to washer.
2. Turn off water supply to washer to avoid  ooding due
to water-pressure surge.
WINTER STORAGE CARE
IMPORTANT: To avoid damage, install and store washer
where it will not freeze. Some water may stay in hoses, and
freezing can damage washer. If storing or moving during
freezing weather, winterize your washer.
To winterize washer:
1. Shut off both water faucets; disconnect and drain water
inlet hoses.
2. Put 1 qt. (1 L) of R.V.-type antifreeze in basket and run
washer on Rinse & Spin cycle for about 30 seconds
to mix antifreeze and remaining water.
3. Unplug washer or disconnect power.
NON-USE AND VACATION CARE
TRANSPORTING YOUR WASHER
1. Shut off both water faucets. Disconnect and drain water
inlet hoses.
2. If washer will be moved during freezing weather, follow
“Winter Storage Care” directions before moving.
3. Disconnect drain hose from drain system and drain any
remaining water into a pan or bucket. Disconnect drain
hose from back of washer.
4. Unplug power cord.
5. Place inlet hoses and drain hose inside washer basket.
6. Drape power cord over edge and into washer basket.
7. Place packing tray from original shipping materials back
inside washer. If you do not have packing tray, place heavy
blankets or towels into basket opening. Close lid and place
tape over lid and down front of washer. Keep lid taped
until washer is placed in new location. Transport washer
in upright position.
WASHER CARE (cont.)
2. Chlorine Bleach Procedure (Alternative):
a. Open the washer lid and remove any clothing or items.
b. Add 1 cup (236 mL) of liquid chlorine bleach to the
bleach compartment.
NOTE: Use of more liquid chlorine bleach than is
recommended above could cause washer damage
over time.
c. Close the washer lid.
d. Do not add any detergent or other chemical
to the washer when following this procedure.
e. Select the cycle recommended for cleaning the inside
of the washer.
f. Press the START/PAUSE/CANCEL button to start
the cycle.
NOTE: For best results, do not interrupt cycle. If cycle
must be interrupted, press START/PAUSE/CANCEL once.
After the cycle has stopped, run a Rinse & Spin cycle to
rinse bleach from washer.
Description of Clean Washer Cycle Operation:
1. This cycle will  ll to a water level higher than in normal
wash cycles to provide rinsing at a level above the water
line for normal wash cycle.
2. During this cycle, there will be some agitation and
spinning to increase the removal of soils.
After this cycle is complete, leave the lid open to allow for
better ventilation and drying of the washer interior.
Cleaning the Dispensers
After a period of using your washer, you may  nd some
residue buildup in the washer’s dispensers. To remove
residue from the dispensers, wipe them with an affresh
®
Machine Cleaning Wipe or a damp cloth and towel dry either
before or after you run the Clean Washer cycle. Do not
attempt to remove the dispensers or trim for cleaning. The
dispensers and trim are not removable. If your model has a
dispenser drawer, however, remove the drawer and clean it
before or after you run the Clean Washer cycle. Use an all-
purpose surface cleaner, if needed.
Cleaning the Outside of the Washer
Use an affresh
®
Machine Cleaning Wipe, a soft, damp cloth,
or a sponge to wipe away any spills. Use an affresh
®
Machine
Cleaning Wipe or only mild soaps or cleaners when cleaning
external washer surfaces.
IMPORTANT: To avoid damaging the washer’s  nish,
do not use abrasive products.
13
REINSTALLING/USING WASHER AGAIN
To reinstall washer after non-use, vacation, winter storage,
or moving:
1. Refer to Installation Instructions to locate, level, and
connect washer.
2. Before using again, run washer through the following
recommended procedure:
To use washer again:
1. Flush water pipes and hoses. Reconnect water inlet hoses.
Turn on both water faucets.
2. Plug in washer or reconnect power.
3. Run washer through Bulky/Sheets cycle to clean washer
and remove antifreeze if used. Use half the manufacturer’s
recommended amount of detergent for a medium-size load.
Troubleshooting
If you experience Possible Causes Solution
Vibration or Off-Balance
Check the following for
proper installation or
see “Using Your Washer”
section
Feet may not be in contact
with the  oor.
Front and rear feet must be in  rm contact with  oor, and
washer must be level to operate properly.
Washer may not be level. Check  oor for  exing or sagging. If  ooring is uneven, a 3/4"
(19 mm) piece of plywood under your washer will reduce sound.
See “Level the Washer” in Installation Instructions.
Load could be unbalanced. Load dry items in loose heaps evenly around basket wall.
Adding wet items to washer or adding more water to basket
could unbalance washer.
Wash smaller loads to reduce imbalance.
Do not tightly pack. Avoid washing single items.
Use Bulky/Sheets cycle for oversized, non-absorbent items
such as jackets and small comforters. See “Cycle Guide.
See “Cycle Guide” and “Using Your Washer” in this Use and
Care Guide.
Noises
Clicking or metallic
noises
Objects caught in washer drain
system.
Empty pockets before washing. Loose items such as coins
could fall between basket and tub or may block pump.
It may be necessary to call for service to remove items.
It is normal to hear metal items on clothing such as snaps,
buckles, or zippers touch against the basket.
Gurgling or humming Washer may be draining water. It is normal to hear the pump making a continuous humming
sound with periodic gurgling or surging as  nal amounts of
water are removed during the Drain & Spin cycles.
Humming Load sensing may be occurring. You may hear the hum of the sensing spins after you have
started the washer. This is normal.
Whirring Basket deceleration may be
occurring.
You may hear the whirring sound of the basket decelerating.
This is normal.
First try the solutions suggested here or visit our website at www.whirlpool.com/owners
(in Canada www.whirlpool.ca/owners) for assistance and to possibly avoid a service call.
14
Troubleshooting
If you experience Possible Causes Solution
Water Leaks
Check the following
for proper installation:
Washer not level. Water may splash off basket if washer is not level. Check that
load is not unbalanced or tightly packed.
Fill hoses not attached tightly. Tighten ll hose connection.
Fill hose washers. Make sure all four ll hose at washers are properly seated.
Drain hose connection. Pull drain hose from washer cabinet and properly secure it
to drain pipe or laundry tub.
Do not place tape over drain opening.
Check household plumbing for leaks
or clogged sink or drain.
Water can back up out of a clogged sink or drain pipe. Check
all household plumbing for leaks (laundry tubs, drain pipe, water
pipes, and faucets).
Washer not loaded as recommended. Improper loading can cause basket to be out of alignment
and cause water to splash off tub. See “Using Your Washer”
for loading instructions.
Washer not performing as expected
Not enough water
in washer
Load not completely covered
in water.
This is normal operation for a high efciency washer. If the Water
Level knob is set to Auto Sensing, the load will not be completely
under water. The washer senses load sizes and adds correct
amount of water for optimal cleaning. Use Bulky/Sheets cycle
for higher water ll, or set Water Level knob to Deep Water Wash
setting. See “What’s Under the Lid” and “Cycle Guide” to match
your load with the best cycle.
IMPORTANT: Do not add more water to washer. Adding water
results in less effective cleaning.
Run Clean Washer with affresh
®
cycle to optimize the water level
and wash performance due to soil buildup in washer basket.
Washer won’t run
or ll, washer stops
working, or wash light
remains on (indicating
that the washer was
unable to ll
appropriately)
Check for proper water supply. Both hoses must be attached and have water owing to
inlet valve.
Both hot and cold water faucets must be turned on.
Check that inlet valve screens have not become clogged.
Check inlet hoses for any kinks, which can restrict water ow.
First try the solutions suggested here or visit our website at www.whirlpool.com/owners
(in Canada www.whirlpool.ca/owners) for assistance and to possibly avoid a service call.
Washer won’t run
or ll, washer stops
working, or wash light
remains on (indicating
that the washer was
unable to ll
appropriately) (cont.)
Check proper electrical supply. Plug power cord into a grounded 3 prong outlet.
Do not use an extension cord.
Ensure there is power to outlet.
Reset a tripped circuit breaker. Replace any blown fuses.
NOTE: If problems continue, contact an electrician.
15
Troubleshooting
If you experience Possible Causes Solution
Washer not performing as expected (cont.)
Washer won’t run
or ll, washer stops
working, or wash light
remains on (indicating
that the washer was
unable to ll
appropriately) (cont.)
Normal washer operation. Lid must be closed for washer to run.
Washer will pause during certain phases of cycle. Do not
interrupt cycle.
Washer may be tightly packed. Remove several items, rearrange load evenly in basket, and add
detergent. Close lid and press START/PAUSE/CANCEL.
Do not add more than one or two additional items after cycle
has started to avoid tightly packing or unbalancing.
Washer not draining/
spinning, loads are still
wet, or nal spin light
remains on (indicating
that the washer was
unable to pump out
water within 10 minutes)
Small items may have been caught
in pump or between basket and tub,
which can slow draining.
Empty pockets and use garment bags for small items.
Using a cycle with a low spin speed. Cycles with lower spin speeds remove less water than cycles
with high spin speeds. Use the recommended cycle/spin speed
for your garment. To remove extra water in the load, select
Drain & Spin. Load may need to be rearranged to allow even
distribution of the load in the basket.
The washer may be tightly packed
or unbalanced.
Tightly packed or unbalanced loads may not allow the washer
to spin correctly, leaving the load wetter than normal. Evenly
arrange the wet load for balanced spinning. Select the Drain &
Spin cycle to remove excess water. See “Using Your Washer”
for loading recommendations.
Check plumbing for correct drain
hose installation. Drain hose
extends into standpipe further
than 4.5" (114 mm).
Check drain hose for proper installation. Use drain hose form
and securely attach to drain pipe or tub. Do not tape over drain
opening. Lower drain hose if the end is higher than 96" (2.4 m)
above the oor. Remove any clogs from drain hose.
Too much detergent causing suds
to slow or stop draining and spinning.
Always measure and follow detergent directions for your load.
To remove extra suds, select Rinse & Spin. Do not add detergent.
Dry spots on load
after cycle
High speed spins extract more
moisture than traditional top-load
washers.
The high spin speeds combined with air ow during the nal
spin can cause items near the top of the load to develop dry
spots during the nal spin. This is normal.
Washer may be tightly packed. Use Bulky/Sheets cycle for higher water ll, or set Water Level
knob to Deep Water Wash setting. See “Cycle Guide” to match
your load with the best cycle.
Added extra garments to the load
after the sensing/ll phase.
Add only one or two additional garments after washer
has started.
Incorrect or wrong
wash or rinse
temperatures
Check for proper water supply. Make sure hot and cold inlet hoses are not reversed.
Both hoses must be attached to both washer and faucet
and have both hot and cold water owing to inlet valve.
Check that inlet valve screens are not clogged.
Remove any kinks in hoses.
Energy saving controlled
wash temperatures.
This washer uses cooler wash and rinse water temperatures
than your previous washer. This includes cooler hot and warm
washes.
Load not rinsed Check for proper water supply. Make sure hot and cold inlet hoses are not reversed.
Both hoses must be attached and have water owing to the
inlet valve.
Both hot and cold water faucets must be on.
Inlet valve screens on washer may be clogged.
Remove any kinks in the inlet hose.
Not using HE detergent or using too
much HE detergent.
The suds from too much detergent can keep washer from
operating correctly. Always measure detergent and follow
detergent directions based on load size and soil level.
Washer not loaded as recommended. The washer is less efcient at rinsing when load is tightly packed.
Load garments in loose heaps evenly around the basket wall.
Load with dry items only.
First try the solutions suggested here or visit our website at www.whirlpool.com/owners
(in Canada www.whirlpool.ca/owners) for assistance and to possibly avoid a service call.
16
Troubleshooting
If you experience Possible Causes Solution
Washer not performing as expected (cont.)
Load not rinsed (cont.) Washer not loaded as recommended
(cont.).
Use cycle designed for the fabrics being washed.
Add only one or two additional garments after washer
has started.
Use Bulky/Sheets cycle for higher water ll, or set Water Level
knob to Deep Water Wash setting. See “Cycle Guide” to match
your load with the best cycle.
Sand, pet hair, lint,
etc. on load after
washing
Heavy sand, pet hair, lint, and
detergent or bleach residues may
require additional rinsing.
Add an extra or deep water rinse to the selected cycle and/or
use Heavy cycle or Deep Water Wash option.
Load is tangling Washer not loaded as recommended. See “Using Your Washer” section.
Select a cycle with a slower wash action and spin speed;
however, items will be wetter than those using a higher-speed
spin.
Use Bulky/Sheets cycle for higher water ll, or set Water
Level knob to Deep Water Wash setting.
See the “Cycle Guide”
to match your load with the best cycle.
Load garments in loose heaps evenly around the basket wall.
Reduce tangling by mixing types of load items. Use the
recommended cycle for the type of garments being washed.
Not cleaning or
removing stains
Added more water to washer. Washer senses load size and adds correct amount of water.
This is normal and necessary for clothes to move. It is normal
for the wash load to be not completely covered in water. Added
water results in less effective cleaning.
Washer not loaded as recommended. Washer is less efcient at cleaning when load is tightly packed.
Load garments in loose heaps evenly around the basket wall.
Load with dry items only.
Add only one or two additional garments after washer
has started.
Adding detergent on top of load. Add detergent, Oxi products, and color-safe bleach to the
bottom of the basket before adding the load items.
Not using HE detergent or using too
much HE detergent.
The suds from regular detergent can keep washer from operating
correctly.
Use only HE detergent. Be sure to measure correctly.
Always measure detergent and follow manufacturer’s directions
based on load size and soil level.
Not using correct cycle for fabric type. Use a higher soil level cycle option (on some models) and
warmer wash temperature to improve cleaning.
Use Heavy cycle for tough cleaning. See the “Cycle Guide”
to match your load with the best cycle.
Not using dispensers.
Use dispensers to avoid chlorine bleach and fabric softener staining.
Load dispensers before starting a cycle.
Do not add products directly onto load.
Not washing like colors together. Wash like colors together and remove promptly after the cycle
is complete to avoid dye transfer.
Incorrect dispenser
operation
Clogged dispenser. Load dispensers before starting a cycle.
Use only liquid chlorine bleach in the bleach dispenser. Use only
fabric softener in the fabric softener dispenser.
Rinse Option knob not set for fabric
softener option.
Set Rinse Option knob to Auto with Extra Rinse, Deep Water
Rinse, or Deep Water with Extra Rinse when using fabric
softener dispenser.
First try the solutions suggested here or visit our website at www.whirlpool.com/owners
(in Canada www.whirlpool.ca/owners) for assistance and to possibly avoid a service call.
17
Troubleshooting
If you experience Possible Causes Solution
Washer not performing as expected (cont.)
Fabric damage Sharp items were in pockets during
wash cycle.
Empty pockets, zip zippers, and snap or hook fasteners before
washing to avoid snags and tears.
Strings and straps could have tangled.
Tie all strings and straps before starting wash load.
Items may have been damaged
before washing.
Mend rips and broken threads in seams before washing.
Fabric damage can occur if load is
tightly packed.
Load garments in loose heaps evenly around the basket wall.
Load with dry items only.
Use cycle designed for the fabrics being washed.
Use Bulky/Sheets cycle for higher water ll, or set Water Level
knob to Deep Water Wash setting. See “What’s Under the Lid”
and “Cycle Guide” to match your load with the best cycle.
Add only one or two additional garments after washer
has started.
Liquid chlorine bleach may have
been added incorrectly.
Do not pour liquid chlorine bleach directly onto load. Wipe up
bleach spills.
Undiluted bleach will damage fabrics. Do not use more than
recommended by manufacturer.
Do not place load items on top of bleach dispenser when
loading and unloading washer.
Garment care instructions may not
have been followed.
Always read and follow garment manufacturer’s care label
instructions. See the “Cycle Guide” to match your load with
the best cycle.
Odors Monthly maintenance not done
as recommended.
See “Washer Care” in “Washer Maintenance.
Unload washer as soon as cycle is complete.
Using too much detergent. Be sure to measure correctly. Always follow the manufacturer’s
directions.
See “Washer Care” section.
Lid Locked light
is ashing
The lid is not closed. Close the lid. The washer will not start with the lid open.
A cycle was stopped or paused
using the Start/Pause/Cancel button.
The washer may still be spinning. The lid will not unlock until the
basket has stopped spinning. This may take several minutes if
washing large loads or heavy fabrics.
Single-dose laundry
packet not dissolving
Adding laundry packet incorrectly. Be sure laundry packet is added to washer basket before
adding clothes. Do not add packet to dispenser. Follow the
manufacturer’s instructions to avoid damage to your garments.
Washer pumps out water
before nishing cycle
Lid is left open for more than
10 minutes.
Make sure lid is closed before starting a cycle and/or during
prewash (soak).
First try the solutions suggested here or visit our website at www.whirlpool.com/owners
(in Canada www.whirlpool.ca/owners) for assistance and to possibly avoid a service call.
18
WHIRLPOOL
®
LAUNDRY
LIMITED WARRANTY
ATTACH YOUR RECEIPT HERE. PROOF OF PURCHASE IS
REQUIRED TO OBTAIN WARRANTY SERVICE.
Please have the following information available when you call the
Customer eXperience Center:
n
Name, address, and telephone number
n
Model number and serial number
n
A clear, detailed description of the problem
n
Proof of purchase including dealer or retailer name and address
DISCLAIMER OF IMPLIED WARRANTIES
IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR IMPLIED WARRANTY OF FITNESS FOR
A PARTICULAR PURPOSE, ARE LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW. Some states and provinces
do not allow limitations on the duration of implied warranties of merchantability or tness, so this limitation may not apply to you. This
warranty gives you specic legal rights, and you also may have other rights that vary from state to state or province to province.
LIMITATION OF REMEDIES; EXCLUSION OF INCIDENTAL AND CONSEQUENTIAL DAMAGES
YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED HEREIN.
WHIRLPOOL SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some states and provinces do not allow
the exclusion or limitation of incidental or consequential damages, so these limitations and exclusions may not apply to you. This
warranty gives you specic legal rights, and you also may have other rights that vary from state to state or province to province.
DISCLAIMER OF REPRESENTATIONS OUTSIDE OF WARRANTY
Whirlpool makes no representations about the quality, durability, or need for service or repair of this major appliance other than the
representations contained in this Warranty. If you want a longer or more comprehensive warranty than the limited warranty that comes
with this major appliance, you should ask Whirlpool or your retailer about buying an extended warranty.
10/17
IF YOU NEED SERVICE:
1. Before contacting us to arrange service, please determine whether your product requires repair. Some questions can be
addressed without service. Please take a few minutes to review the Troubleshooting section of the Use and Care Guide
or visit the “HOW-TOS & FAQS” section of https://www.whirlpool.com/owners.html.
2. All warranty service is provided exclusively by our authorized Whirlpool Service Providers.
In the U.S. and Canada, direct all requests for warranty service to:
Whirlpool Customer eXperience Center
In the U.S.A. call 1-866-698-2538. In Canada call 1-800-807-6777.
If outside the 50 United States and Canada, contact your authorized Whirlpool dealer to determine if another warranty applies.
ONE YEAR LIMITED WARRANTY
WHAT IS COVERED
WHAT IS NOT COVERED
1. Commercial, non-residential, multiple-family use, or use inconsistent with published
user, operator, or installation instructions.
2. In-home instruction on how to use your product.
3. Service to correct improper product maintenance or installation, installation not in
accordance with electrical or plumbing codes, or correction of household electrical
or plumbing (e.g., house wiring, fuses, or water inlet hoses).
4. Consumable parts (e.g., light bulbs, batteries, air or water lters, preservation
solutions).
5.
Defects or damage caused by the use of non-genuine Whirlpool parts or accessories.
6. Conversion of your product from natural gas or propane gas or reversal
of appliance doors.
7. Damage from accident, misuse, abuse, re, oods, acts of God, or use with
products not approved by Whirlpool.
8. Repairs to parts or systems to correct product damage or defects caused by
unauthorized service, alteration, or modication of the appliance.
9. Cosmetic damage including scratches, dents, chips, and other damage to appliance
nishes unless such damage results from defects in materials and workmanship and
is reported to Whirlpool within 30 days.
10. Discoloration, rust, or oxidation of surfaces resulting from caustic or corrosive
environments, including but not limited to, high salt concentrations, high moisture
or humidity, or exposure to chemicals.
11. Pick-up or delivery. This product is intended for in-home repair.
12. Travel or transportation expenses for service in remote locations where an
authorized Whirlpool servicer is not available.
13. Removal or reinstallation of inaccessible appliances or built-in xtures (e.g., trim,
decorative panels, ooring, cabinetry, islands, countertops, drywall) that interfere
with servicing, removal, or replacement of the product.
14. Service or parts for appliances with original model/serial numbers removed, altered,
or not easily determined.
The cost of repair or replacement under these excluded circumstances shall be
borne by the customer.
For one year from the date of purchase,
when this major appliance is installed,
operated, and maintained according
to instructions attached to or furnished
with the product, Whirlpool Corporation
or Whirlpool Canada LP (hereafter
“Whirlpool”) will pay for Factory
Specified Replacement Parts and repair
labor to correct defects in materials or
workmanship that existed when this major
appliance was purchased, or at its sole
discretion replace the product. In the event
of product replacement, your appliance
will be warranted by the remaining term of
the original unit’s warranty period.
YOUR SOLE AND EXCLUSIVE REMEDY
UNDER THIS LIMITED WARRANTY
SHALL BE PRODUCT REPAIR AS
PROVIDED HEREIN. Service must be
provided by a Whirlpool designated
service company. This limited warranty
is valid only in the United States or
Canada and applies only when the major
appliance is used in the country in which
it was purchased. This limited warranty
is effective from the date of original
consumer purchase. Proof of original
purchase date is required to obtain service
under this limited warranty.
19
Sécurité de la laveuse
20
Ce qui est sous le couvercle
Utiliser uniquement un détergent haute efcacité (HE).
IMPORTANT :
Le couvercle doit être fermé avant que le panier de la laveuse se remplisse et que le programme de lavage se mette en marche.
Si le couvercle est ouvert, le programme s’arrête et tous les mouvements de remplissage/agitation s’arrêtent. Une fois le couvercle
fermé, le programme reprend automatiquement. Toutefois, si le bouton Start/Pause/Cancel (mise en marche/pause/annulation) est
pressé avant d’ouvrir le couvercle, il faut fermer le couvercle et appuyer de nouveau sur le bouton Start/Pause/Cancel (mise en
marche/pause/annulation) pour reprendre le programme.
Option de rinçage doit être réglée sur Auto with Extra Rinse (auto avec rinçage supplémentaire), Deep Water Rinse (rinçage
à l’eau profonde) ou Deep Water with Extra Rinse (rinçage à l’eau profonde avec rinçage supplémentaire) lors de l’utilisation
d’assouplissant pour tissu dans le distributeur d’assouplissant pour tissu. Cela garantit que l’assouplissant pour tissu est
ajouté au bon moment dans la phase de rinçage et est uniformément répartie.
Verrouillage du couvercle
Pour permettre des essorages à vitesse plus élevée, le
couvercle se verrouille et le témoin de Lid Locked (couvercle
verrouillé) s’allume. Lorsque ce témoin lumineux s’allume, cela
signie que le couvercle est verrouillé et ne peut être ouvert
sans suspendre le programme. Lorsque ce témoin lumineux
clignote, cela signie que la laveuse effectue une pause.
Lorsque ce témoin lumineux est éteint, cela signie qu’on peut
ouvrir le couvercle. Une fois qu’un programme a commencé,
la laveuse se remplit au niveau d’eau approprié. Sur certains
programmes, l’agitation se produit pendant que le panier se
remplit d’eau. Ceci est normal. Quand la laveuse est faite
remplir, l’étape de lavage va commencer. Si l’on doit ouvrir
le couvercle pour ajouter un vêtement après cette étape, le
couvercle de la demeurera déverrouillé pendant toute la partie
de l’agitation de l’étape de lavage. Le programme fait une
pause automatiquement quand le couvercle est ouvert, et le
programme recommencera après la fermeture du couvercle.
Le couvercle se verrouille avant le début de l’étape d’essorage.
Si l’on doit pauser ou arrêter après cette étape, il faut appuyer
sur START/PAUSE/CANCEL (mise en marche/pause/annulation)
puis attendre que le couvercle se déverrouille. Le couvercle
se déverrouille uniquement une fois que le mouvement de la
laveuse a cessé. Selon le moment où l’on souhaite suspendre
le programme, le couvercle peut mettre entre quelques
secondes et plusieurs minutes à se déverrouiller. Appuyer sur
START/PAUSE/CANCEL (mise en marche/pause/annulation)
pour poursuivre le programme.
Détection
Cette laveuse détecte automatiquement la taille de la charge
pour la plupart des programmes, et sélectionne un niveau
d’eau approprié en fonction de la taille de la charge détectée.
Cette laveuse effectue également une série d’essorages pour
contrôler l’équilibre de la charge. Durant cette période, une série
de cliquetis et un bruit de frottements rythmiques indiquent
que la technologie de détection détermine si la charge est
déséquilibrée.
Options de niveau d’eau
Régler le bouton Water Level (niveau d’eau) sur le réglage
Auto Sensing (détection automatique) et la laveuse ajuste
automatiquement le niveau d’eau en fonction de la taille de
la charge. Régler le bouton Water Level (niveau d’eau) sur
le réglage Deep Water Wash (lavage à l’eau profonde) et la
laveuse ajoute automatiquement plus d’eau à n’importe quel
programme à tout moment pendant le processus de lavage.
Sons normaux prévisibles
Au cours des différents stades du programme de lavage, vous
entendrez peut-être des bruits que votre laveuse précédente
ne produisait pas. Par exemple, vous entendrez peut-être un
cliquetis au début de l’étape d’essorage lorsque le système
de verrouillage du couvercle effectue un test automatique.
Différents bourdonnements et bruits de frottements rythmiques
se produiront à mesure que l’agitateur HE évalue l’équilibre
de la charge et qu’il la déplace. Parfois, il est possible que la
laveuse soit complètement silencieuse, lorsqu’elle détermine le
niveau d’eau adéquat ou qu’elle laisse tremper les vêtements.
Rinçage par vaporisation
Certains programmes utilisent l’option rinçage par
vaporisation par défaut. Au cours de ces programmes,
on entend l’eau pénétrer dans la laveuse tandis que la cuve
tourne, ce qui permet à l’eau de rinçage de pénétrer les
vêtements. Consulter le “Guide des programmes” pour
plus de détails.
Choix du détergent approprié
Utiliser uniquement des détergents haute efcacité. L’emballage
portera la mention “HE” ou “High Efciency” (haute efcacité).
Il est probable que l’utilisation d’un détergent non HE
prolongera la durée des programmes et réduira la performance
de rinçage. Ceci peut aussi entraîner des malfunctions de
composants et, avec le temps, une accumulation de moisissure.
Les détergents HE devraient produire peu de mousse et se
dissoudre rapidement pour produire une quantité de mousse
idéale pour une performance optimale. Ils devraient retenir
les particules de saleté en suspension an qu’elles ne se
redéposent pas sur les vêtements propres. Les détergents
identiés HE ne comportent pas tous une formule identique
et ne produisent pas tous la même quantité de mousse. Par
exemple, les détergents HE naturels, organiques et faits maison
peuvent produire une plus grande quantité de mousse. Toujours
suivre les instructions du fabricant pour déterminer la quantité
de détergent à utiliser.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40

Whirlpool WTW4955HW Mode d'emploi

Catégorie
Machines à laver
Taper
Mode d'emploi

dans d''autres langues