Interlogix TX Wireless Keyfob Guide d'installation

Interlogix
Marque
Interlogix
Modèle
TX Wireless Keyfob
Taper
Guide d'installation

Ce manuel convient également à

P/N 466-5423 • REV A • 20SEPT2018 © 2018 United Technologies Corporation. All rights reserved
TX+2WAYFOB Wireless Keyfob Installation Instructions
PLEASE SEE REVERSE SIDE FOR IMPORTANT PRODUCT
WARNINGS AND DISCLAIMER INFORMATION.
Description
The TX+2WAYFOB is an unsupervised wireless keyfob device that when within
operational range of an Interlogix control panel or receiver, can remotely arm,
disarm, and perform other functions specific to the system.
The TX+2WAYFOB features the TX+ Encryption protocol which provides encrypted
wireless communication to select Interlogix control panels, as well as 2-way
communication functionality providing acknowledgement at the device via the tri-
color LED that transmissions sent have been received by the panel. Please refer to
your panel’s installation instructions to see if it is TX+ Encrypted capable.
The TX+2WAYFOB also utilizes the standard ITI-319 protocol which is compatible
with all Interlogix control panels and receivers. When enrolled into a panel and
operating in the standard ITI-319 mode, the device functions in 1-way mode only and
does not receive acknowledgement signals back from the panel.
Figure 1: TX+2WAYFOB
Enrollment Into TX+ Encryption Supported Panels
To enroll the TX+2WAYFOB as an encrypted keyfob into a panel that supports the
TX+ Encryption protocol, follow these steps:
1) Place the panel into program mode, then go to Learn Sensors menu.
Refer to your specific alarm panel manual for details on these menus.
2) Once the Learn Sensors mode has been activated, press and hold both
the STAR and LOCK buttons together for 5 seconds. The LED
will blink red one time upon transmission, followed by an alternating RED
and GREEN blinks (6 times total) for successful acknowledgement of
enrollment into the panel.
3) If the panel does not respond after completing step 2, repeat as
necessary until the device is successfully enrolled into the panel.
Note: Utilization of the TX+ Encrypted protocol is only compatible with select
Interlogix control panels. When enrolled into a panel that is TX+ Encrypted
capable, the enrollment menu screen may indicate “TX+ Encrypted” to verify
that the sensor is communicating to the panel via the encrypted protocol.
Please refer to your panel’s installation instructions to verify that the panel
supports TX+ Encrypted capability.
If the keyfob is unintentionally enrolled into a TX+ Encryption supported panel in the
standard ITI-319 protocol mode, the device will need to be removed from the panel,
and the keyfob Reset/Restore function will need to be performed before attempting
to re-enroll in the TX+ Encryption mode. The Reset/Restore function is performed by
pressing and holding the UNLOCK and LIGHT buttons together for 5 seconds.
The LED will remain illuminated green for 3 seconds following the successful
reset/restoral.
Enrollment into Non TX+ Encryption Supported Panels (ITI-
319 Protocol, one-way mode only)
To enroll the TX+2WAYFOB into a panel utilizing the standard ITI-319 protocol,
follow these steps:
1) Place the panel into program mode, then go to Learn Sensors menu.
Refer to your specific alarm panel manual for details on these menus.
2) Once the Learn Sensors mode has been activated, press and hold both
the LOCK and UNLOCK buttons together for 5 seconds.
The LED will blink red one time upon transmission. Then select the
appropriate sensor group and number on the panel. Refer to your specific
alarm panel manual for details on the different sensor groups.
3) If the panel does not respond after completing step 2, repeat as
necessary.
Note: When the TX+2WAYFOB is enrolled into a panel utilizing the standard ITI-319
protocol, the 2-way communication functionality is not available and it will operate as
a standard 1-way device.
Operation in TX+ Encrypted Mode
When the TX+2WAYFOB is enrolled into an Interlogix panel/receiver that supports
the TX+ Encrypted protocol, and the device is communicating via the TX+ Encrypted
protocol, the following chart indicates the different transmissions possible, along with
their corresponding LED acknowledgements after the initial RED blink upon
transmission:
FUNCTION
KEYFOB ACTION
LED RESPONSE
PANEL STATUS
Enrollment
Hold STAR and LOCK together
for 5 seconds
RED LED blink
once, followed by
RED/GREEN
alternating
Device
successfully
enrolled
Arm Stay
Press LOCK once
RED LED
blinks 2 times
Panel Armed
Stay
Arm Away
Press LOCK twice
RED LED
blinks 4 times
Panel Armed
Away
Disarm
Press UNLOCK once
GREEN LED
blinks 3 times
Panel Disarmed
Panic
Hold LOCK and UNLOCK
together for 3 seconds
RED/GREEN
alternating
Panic Alarm
Re-sync
(only done
during sensor
test mode)
Hold STAR and LOCK together
for 5 seconds
RED/GREEN
alternating
Device
successfully
resynchronized
Reset/Restore
Hold UNLOCK and LIGHT
together for 5 seconds
GREEN LED
stays on for 3
seconds
Keyfob reverts
back to factory
defaults
P/N 466-5423 • REV A • 20SEPT2018 © 2018 United Technologies Corporation. All rights reserved
Trouble Conditions in TX+ Encrypted Mode
After the TX+2WAYFOB is enrolled into an Interlogix panel/receiver that supports the
TX+ Encrypted protocol, and the device is communicating via the TX+ Encrypted
protocol, the following chart indicates the different trouble conditions that can occur,
identified by the following LED responses on the keyfob:
Keyfob Action
LED Response
Meaning
When any button
press or sequence
is initiated
YELLOW LED
blinks 3 times
System cannot arm/disarm/perform
function due to trouble condition at panel.
Refer back to the panel to understand
what trouble condition exists
When any button
press or sequence
is initiated
YELLOW LED
stays on for 3 seconds
No acknowledgement received from the
panel. When this occurs, two conditions
may exist:
1) the panel has received the keyfob
transmission and has entered into the
desired state, but the keyfob is too far out
of range to receive the acknowledgement
messages back from the panel.
2) the keyfob is too far out of wireless
range and the panel did NOT receive the
keyfob transmission, resulting in no state
change at the panel
When any button
press or sequence
is initiated
RED/GREEN/YELLOW
alternating LED blinks
Re-sync required (panel needs to be
placed into Sensor Test Mode and the re-
sync function needs to be completed)
Operation in ITI-319 Mode
When the TX+2WAYFOB is enrolled into an Interlogix panel/receiver and the device
is communicating via the ITI-319 protocol, the following chart indicates the different
transmissions possible, along with their corresponding LED acknowledgements.
Please refer to your panel’s installation instructions for further detail on which keyfob
functions may or may not be available.
LOCK
Depending on your control panel:
Press once to arm in Stay mode. LED blinks RED once upon transmission.
Press twice to arm in Away mode. LED blinks RED once upon transmission.
UNLOCK
Press this button to disarm the system. LED blinks RED once upon transmission.
LIGHT
For NetworX panels, press this button to arm the system in Stay mode. For Concord
or Simon XT, it can turn system-controlled lights on or off. LED blinks RED once
upon transmission.
STAR
The star button function depends on the individual panel programming. Refer to the
installation instructions for your panel. LED blinks RED once upon transmission.
PANIC or AUX
If the keyfob is programmed using a panic or portable auxiliary group number,
pressing the LOCK and UNLOCK buttons simultaneously will activate an audible or
silent alarm (depending on the group number) and initiate reports to the central
station. LED blinks RED once upon transmission.
Replacing the Battery
The TX+2WAYFOB comes pre-installed with a single Panasonic CR-2450 Lithium
coin-cell battery that provide up to 10 years of battery life under normal usage
conditions. Because keyfobs are non-supervised devices, a low battery signal will
only be received by the control panel when the device is within range of the receiver
and a button is pressed (if the device is not in use, no low battery signal will be sent
until a button is pressed). When the device is carried beyond the range of the
receiver and/or is seldom used/tested, the battery could wholly deplete without a
warning of the battery condition being sent to the panel. If the LED on the device
appears dim or does not turn on when a button is pressed, it is a warning that the
battery may be low or depleted and should be replaced. To ensure proper
functionality, test the device weekly and follow these simple steps to replace the
battery when necessary:
1) Remove the case cover from the back housing by inserting a small flat
head screwdriver into the slot at the bottom of the device and press on
the tab.
2) Remove the existing battery and re-install a new Panasonic CR-2450
battery. When inserting the battery, pay close attention to the battery
polarity indicators to ensure proper placement.
3) Replace the case cover and perform a sensor test to ensure proper
communication to the panel/receiver.
TX+2WAYFOB
RF Frequency
Compatibility
(TX+ Encrypted)
Compatibility
(Standard ITI-319)
Battery Type
Typical Battery Life
Operating Temperature Range
Relative Humidity
Supervisory Interval
Storage Temperature Range
Dimensions
FCC Compliance Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may
not cause harmful interference, and (2) this device must accept any interference received, including interference that may
cause undesired operation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by UTC Fire and Security could void the user’s authority to operate the
equipment.
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two
conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including
interference that may cause undesired operation of the device.
Cet appareil est conforme avec Industrie Canada exempts de licence standard RSS (s). Son fonctionnement est soumis aux
deux conditions suivantes: (1) cet appareil ne doit pas provoquer d'interférences et (2) cet appareil doit accepter toute
interférence, y compris celles pouvant causer un mauvais fonctionnement de l'appareil.
In accordance with FCC requirements of human exposure to radiofrequency fields, the radiating element shall be installed
such that a minimum separation distance of 20 cm is maintained from the general population.
Conformément aux exigences d'Industrie Canada en matière d'exposition humaine aux champs de radiofréquences,
l'élément rayonnant doit être installé de telle sorte qu'une distance minimale de 20 cm soit maintenue par rapport à la
population générale.
FCC: 2ABBZ-RF-FOB-319-2W
IC: 11817A-RFFOB3192W
This Class B digital apparatus complies with Canadian ICES-3B.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
Contact information
For contact information, visit us online at www.interlogix.com.
For technical support, see www.interlogix.com/support
Copyright
Copyright © 2018 United Technologies Corporation. All rights reserved.
Trademarks
Interlogix is a registered trademark of United Technologies Corporation. Interlogix is part of UTC Climate, Controls & Security, a
unit of United Technologies Corporation.
Product Warnings and Disclaimers
WARNING: CHOKING HAZARD - Small parts. Keep away from children.
ATTENTION: RISQUE D'ÉTOUFFEMENT – Petite pice. Garder eloigner des enfants.
THESE PRODUCTS ARE INTENDED FOR SALE TO, AND INSTALLATION BY, AN EXPERIENCED SECURITY
PROFESSIONAL. UTC FIRE & SECURITY CANNOT PROVIDE ANY ASSURANCE THAT ANY PERSON OR ENTITY
BUYING ITS PRODUCTS, INCLUDING ANY “AUTHORIZED DEALER”, IS PROPERLY TRAINED OR EXPERIENCED TO
CORRECTLY INSTALL SECURITY RELATED PRODUCTS.
CES PRODUITS SONT DESTINÉS À ÊTRE VENDUS ET INSTALLÉS PAR UN PROFESSIONNEL DE SÉCURITÉ
EXPÉRIMENTÉ. UTC FIRE & SECURITY NE PEUT FOURNIR AUCUNE ASSURANCE QUE TOUTE PERSONNE OU
ENTITÉ QUI ACHETERA SES PRODUITS, Y COMPRIS TOUT «DÉTAILLANT AGRÉÉ», EST CORRECTEMENT
FORMÉE OU EXPÉRIMENTÉE À INSTALLER CORRECTEMENT LES PRODUITS LIÉS À LA SÉCURITÉ
For more information on warranty disclaimers and product safety information, please check
https://firesecurityproducts.com/policy/product-warning or scan the following code:
  • Page 1 1
  • Page 2 2

Interlogix TX Wireless Keyfob Guide d'installation

Interlogix
Marque
Interlogix
Modèle
TX Wireless Keyfob
Taper
Guide d'installation
Ce manuel convient également à
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes

Autres documents