Heartland HCFDR23CBL Le manuel du propriétaire

AGA Marvel

1260 E. VanDeinse St.

Greenville MI 48838

Toll free phone: 800-223-3900

Fax: 616-754-9690

www.agamarvel.com

THANK YOU for purchasing this high-quality product. If you should experience a problem not covered

in TROUBLESHOOTING, please visit our website at www.agamarvel.com for additional information. If

you still need assistance, call us at 1-800-223-3900.

You will need your model and serial number, located on the inside wall of the refrigerator compart-

ment.

Classic Model HCFDR23C Refrigerator User Instructions

2

NOTE

!

CAUTION

!

CAUTION

Important Safety Instructions

Warnings and safety instructions appearing in this guide

are not meant to cover all possible conditions and situa-

tions that may occur. Common sense, caution, and care

must be exercised when installing, maintaining, or operat-

ing this appliance.

Recognize Safety Symbols,

Words, and Labels.

!

WARNING

WARNING-You can be killed or seriously injured if

you do not follow these instructions.

CAUTION-Hazards or unsafe practices which could re-

sult in personal injury or property / product damage.

NOTE-Important information to help assure a problem

free installation and operation.

State of California Proposition 65 Warnings:

WARNING: This product contains one or more chemicals

known to the State of California to cause cancer.

WARNING: This product contains one or more chemicals

known to the State of California to cause birth defects or

other reproductive harm..

Table of Contents

Table of contents ................................................................2

Safety .................................................................................2

Unpacking your appliance ..................................................3

Electrical information ..........................................................4

Feature overview ................................................................5

Product dimensions ............................................................6

Installation ..........................................................................7

Removing the doors ..........................................................11

Connecting the water supply .............................................13

Controls ............................................................................14

Ice maker ..........................................................................16

Storage features ...............................................................17

Storing food and saving energy .......................................21

Normal operating sounds .................................................22

Changing water and air lters............................................23

Care and cleaning ............................................................25

Replacing LED lights ........................................................27

Solutions to common problems ........................................28

Warranty ...........................................................................31

FINDING INFORMATION AND SAFETY

CFC/HCFC DISPOSAL

Your old refrigerator may have a cooling system that used

CFCs or HCFCs (chlorouorocarbons or hydrochlorouo-

rocarbons). CFCs and HCFCs are believed to harm strato-

spheric ozone if released to the atmosphere. Other refriger-

ants may also cause harm to the environment if released to

the atmosphere.

If you are throwing away your old refrigerator, make sure

the refrigerant is removed for proper disposal by a qualied

technician. If you intentionally release refrigerant, you may

be subject to nes and imprisonment under provisions of

environmental legislation.

• Do not store or use gasoline or other ammable liquids

near this or any other appliance. Read product labels

for warnings regarding ammability and other hazards.

• Do not operate the refrigerator in the presence of ex-

plosive fumes.

• Avoid contact with any moving parts of the automatic

ice maker.

3

!

CAUTION

Help Prevent Tragedies

Child entrapment and suffocation are not problems of the

past. Junked or abandoned refrigerators are still dangerous

- even if they sit out for "just a few hours".

If you are getting rid of your old refrigerator, please follow

the instructions below to help prevent accidents.

Before you throw away your old refrigerator or freezer:

• Take off the doors or remove the drawers.

• Leave the shelves in place so children may not easily

climb inside.

NOTE

!

CAUTION

!

CAUTION

!

WARNING

EXCESSIVE WEIGHT HAZARD

Use two or more people to move product.

Failure to do so can result in personal injury.

Remove Interior Packaging

Your appliance has been packed for shipment with all parts

that could be damaged by movement securely fastened.

Remove internal packing materials and any tape holding in-

ternal components in place. The owners manual is shipped

inside the product in a plastic bag along with the warranty

registration card, and other accessory items.

Important

Keep your carton and packaging until your appliance has

been thoroughly inspected and found to be in good condi-

tion. If there is damage, the packaging will be needed as

proof of damage in transit. Afterwards please dispose of all

items responsibly.

Dispose of the plastic bags which can be a suffocation

hazard.

Note to Customer

This merchandise was carefully packed and thoroughly

inspected before leaving our plant. Responsibility for its

safe delivery was assumed by the retailer upon acceptance

of the shipment. Claims for loss or damage sustained in

transit must be made to the retailer.

DO NOT RETURN DAMAGED MERCHANDISE TO THE

MANUFACTURER - FILE THE CLAIM WITH THE

RETAILER.

If the appliance was shipped, handled, or stored in other

than an upright position for any period of time, allow the ap-

pliance to sit upright for a period of at least 24 hours before

plugging in. This will assure oil returns to the compressor.

Plugging the appliance in immediately may cause damage

to internal parts.

Warranty Registration

It is important you send in your warranty registration card

immediately after taking delivery of your appliance or you

can register online at www.agamarvel.com.

The following information will

be required when registering

your appliance.

Model Number

Serial Number

Date of Purchase

Dealer’s name and address

The service number and serial number can be found on the

serial plate which is located inside the right side refrigerator

cabinet on the right side of the cabinet liner. (See gure 1).

Figure 1

Online registration

available at

www.agamarvel.com

UNPACKING YOUR APPLIANCE

4

Electrical information

• The refrigerator must be plugged into its own dedicat-

ed 115 Volt, 60 Hz, AC-only non-GFCI electric outlet.

The power cord of the appliance is equipped with a

three-prong grounding plug for your protection against

electrical shock hazards. It must be plugged directly

into a properly grounded three-prong receptacle. The

receptacle must be installed in accordance with local

codes and ordinances. Consult a qualied electrician.

Do not use an extension cord or adapter plug.

• If the power cord is damaged, it should be replaced

by the manufacturer, service technician, or a qualied

person.

• Never unplug the refrigerator by pulling on the power

cord. Always grip the plug rmly and pull straight out

from the receptacle to prevent damaging the power

cord.

• To avoid electrical shock, unplug the refrigerator before

cleaning and before replacing a light bulb or LED light.

• Performance may be affected if the voltage varies by

10% or more. Operating the refrigerator with insufcient

power can damage the compressor. Such damage is

not covered under your warranty.

• Do not plug the unit into an outlet controlled by a wall

switch or pull cord to prevent the refrigerator from being

turned off accidentally.

Figure 2

Figure 3

Do not remove

ground prong

!

WARNING

You must follow these guidelines to ensure

that your refrigerator’s safety mechanisms are

operating correctly.

Figure 4

Grounding type

wall receptacle

!

CAUTION

To turn off power to your refrigerator, unplug the

power cord from the wall outlet.

ELECTRICAL INFORMATION

5

Flipper Guide

LED lights

Covered

door bin

Flipper

mullion

Air lter

ShelvesShelves

Crisper

drawer

Crisper

drawer

Tilt-out

bin

LED lightLED light

Freezer baskets

Water

lter

Ice

maker

Ice

bucket

Toe grille

Wire tilt-out shelf

(inside freezer drawer)

FEATURE OVERVIEW

Understanding features and terms

Your refrigerator is designed for optimal convenience and

storage exibility. The illustration below is provided to assist

you with familiarizing yourself with product features and

terminology.

Model is shown

without freezer

door cover

Select

temperature

drawer

Door

hinges

Figure 5

Specialty items rack,

inside drawer

6

PRODUCT DIMENSIONS

Rough In

Measurements

OPTIONAL COWL

Dimensions

•

• Cut-out height of opening will de-

pendant on installation of cowl op-

tion. See adjacent Figure.

Electrical

Water

1” (2.5 cm)

air gap

24” (61 cm)

cabinet depth

41-1

/4”

(105 cm)

w/ door open 90

4” (10.2 cm)

gap

for door swing

25” (63.5 cm)

counter depth

36-1/2”

(92.7 cm)

4/1-07

(

)mc 4.871

no cowl

76-1/4”

”

(

193.7 cm)

6” cowl

Dimensions

Body Width

35 5/8”

(90.5 cm)

Hinge

3/8”

front leg

adjusters

front

stabilizers

with freezer drawer open

6 1/8”

(15.6 cm)

4 1/4”

(10.8 cm)

24”

(61 cm)

Refrigerator

Optional 6” (15 cm) high cowl - part

number 30059 - color.

Note: Color to be specified at time

of order.

68 3/16”

(173.2 cm)

23 5/8”

(60.0 cm)

26 7/8”

(68.3 cm)

44 1/2”

(113.0 cm)

25”

(63.5 cm)

70”

(177.8 cm)

Figure 6

Figure 7

Figure 8

Figure 9

7

INSTALLATION

Required tools

You will need the following tools:

Components

provided:

Top hinge

cover

rear screw

Top hinge cover

front screw

Lower

hinge

screw

Top

hinge

screw

Tools necessary:

Phillips™ Head

or #2 square

drive head

(or)

(or) (or)

And

Socket wrench set

Adjustable

wrench

3/8" Fixed

wrench

1/4" Nut

driver

This Use & Care Guide provides general installation and

operating instructions for your model. We recommend

using a service or kitchen contracting professional to install

your refrigerator. Use the refrigerator only as instructed in

this Use & Care Guide. Before starting the refrigerator,

follow these important rst steps.

Location

• Choose a place that is near a grounded, non-GFCI,

electrical outlet. Do Not use an extension cord or an

adapter plug.

• If possible, place the refrigerator out of direct sunlight

and away from the range, dishwasher, or other heat

sources.

• The refrigerator must be installed on a oor that is level

and strong enough to support a fully loaded refrigerator.

• Consider water supply availability for models equipped

with an automatic ice maker.

!

CAUTION

DO NOT install the refrigerator where the temperature will

drop below 55°F (13°C) or rise above 110°F (43°C). The

compressor will not be able to maintain proper tempera-

tures inside the refrigerator.

DO NOT block the toe grille on the lower front of your re-

frigerator. Sufcient air circulation is essential for the proper

operation of your refrigerator.

Installation

• Allow the following clearances for ease of installation,

proper air circulation, and plumbing and electrical con-

nections:

Sides & Top ⅜ inch (9.5 mm)

Back 1 inch (25.4 mm)

NOTE

If your refrigerator is placed with the door hinge against a

wall, you may have to allow additional space so the door

can be opened wider.

Door opening

The refrigerator doors are designed to shut by themselves

within a 20 degree opening.

Your refrigerator should be positioned to allow easy access

to a counter when removing food. For best use of refrigera-

tor drawers and freezer baskets, the refrigerator should be

in a position where both can be fully opened.

Guidelines for nal positioning of your refrig-

erator

• All four corners of the cabinet must rest rmly on the

oor.

• The cabinet should be level at the front and rear.

• The sides should tilt ¼ inch (6 mm) from front to back

(to ensure that doors close and seal properly).

• Doors should align with each other and be level.

Most of these conditions can be met by raising or

lowering the adjustable front rollers.

Figure 10

8

INSTALLATION

Leveling Freezer Drawer (if necessary)

1. Check gasket seal around top, bottom, and sides of

freezer drawer.

2. If gasket is not sealed, open drawer and slightly loosen

four drawer screws (two on each side) to allow drawer

to rotate (see illustration).

3. Close drawer and recheck the seal on the gasket (A).

Open the drawer grabbing by the sides in the center

(B). Be careful not to rotate the drawer.

Remove hex

head drawer

screw

Remove hex

head drawer

screw

Remove hex

head drawer

screw

Remove hex

head drawer

screw

Do not remove

other screws

4. Tighten four drawer screws.

5. Recheck gasket seal.

Push

against

freezer

drawer

Grab

drawer

at center

from both

sides

then

pull

drawer

out

A

B

Level Refrigerator & Adjust Doors (if neces-

sary)

Guidelines for nal positioning of your refrigerator:

• All four corners of the cabinet must rest rmly on the

oor.

• The sides should tilt ¼ inch (6 mm) from front to back

(to ensure that doors close and seal properly).

• Doors should align with each other and be level.

Most of these conditions can be met by raising or low-

ering the adjustable front rollers.

To level the cabinet using the front rollers:

1. Slightly open freezer drawer.

2. Remove the toe grille. See Figure 13.

Figure 13: Remove screws and then gently pull forward.

Remove

mounting

screws

3. You can raise or lower each door. Use a ⅜ inch socket

wrench to turn the adjustment screws (one per side).

To raise: turn adjustment screw clockwise.

To lower: turn adjustment screw counterclockwise.

4. Ensure both doors are bind-free with their seals touch-

ing the cabinet on all four sides and that cabinet is

stable.

5. After unit is leveled, lower anti-tip leg until it contacts

the oor.

6. Install the toe grille by tting into place (replacing

screws on some models).

Door Door

Anti-tip

leg

Raise

Lower

Figure 11

Figure 12

Figure 13

Figure 14

9

INSTALLATION

To adjust the door stop:

Door stop is adjustable between 85 to 145 degrees.

NOTE

View shown is looking up at the bottom of the refrigerator

door.

1. Open door to provide access to screw.

2. Loosen screw.

3. Adjust door to desired location.

4. Rotate door stop until it makes contact with the lower

hinge.

5. Re-tighten screw.

6. Ensure door stops in desired location before resuming

normal use.

Lower

hinge

Door

stop

Screw

Adjustable door stop

Adjusting door

Rotate door

to desired

location

Rotate

door

stop

Re-tighten

screw

Re-tighten screw

Figure 15

Figure 16

Figure 17

10

INSTALLATION

Adjusting ipper mullion screw

Adjusting ipper mullion height

Thickness

of a coin

Flipper

mullion

Flipper

mullion

Mullion

guide

Screw

Flipper

mullion

hinge

To adjust the ipper mullion:

1. Loosen the screw located on the ipper mullion hinge.

2. Adjust ipper mullion height. For proper connection with

the ipper mullion guide, there should be a separation

about the thickness of a coin (0.060 inches, or 1.5 mm)

between the guide and ipper mullion.

3. Re-tighten screw.

Figure 18

Figure 19

11

REMOVING THE DOORS

Getting through narrow spaces

If your refrigerator will not t through an entrance area,

you can remove the doors. Check rst by measuring the

entrance.

To prepare for removing the doors:

1. Make sure the electrical power cord is unplugged from

the wall outlet.

2. Open the freezer drawer and remove the toe grille (see

“Installation” section).

3. Remove any food from the door shelves and close the

doors.

To remove the top hinge covers:

1. Remove the two screws from each cover over the top

door hinges.

2. Lift inside edge of hinge cover and tilt back.

NOTE

DO NOT remove the ground screw from hinge.

To remove the refrigerator doors:

1. Trace lightly around the door’s top hinges with a pencil.

This makes reinstallation easier.

2. Disconnect the harness by grasping both sides of the

connector rmly, depress the latch, and pull apart. Re-

move the two screws from the top hinge. Lift the door

off of the bottom hinge and set it aside.

3. Unscrew the three lower hinge screws and hinge if

necessary.

To reinstall the right door, reverse the above steps.

lower hinge removal

Once both doors are in place, ensure they are aligned with

each other and level (please see the “Installation” section

for more details), and replace the top hinge cover.

!

CAUTION

Be sure doors are set aside in a secure position where they

cannot fall and cause personal injury, or damage to the

doors or handles.

Front

cover screw

Top hinge

cover

Hinge

screws

Rear

cover

screw

Ground

screw

Top

hinge

Multi-wire

cables

Leave

hinge

with

door

Figure 20

Figure 21

Figure 22

Figure 23

12

REMOVING THE DOORS

!

CAUTION

Drawer is heavy. Use caution when lifting.

Removing Freezer Drawer

1. Open freezer drawer.

2. Remove drawer screws on right and left sides (two

screws on each side).

3. Lift drawer up and out to remove.

Installing Freezer Drawer

1. With lower slides pulled out, hang drawer onto slide

brackets ensuring pins on each side are fully inserted

into slots on each side.

2. Reinstall four drawer screws (two per side), tighten

down, and close drawer (C).

3. Check gasket seal around top, bottom, and sides of

freezer drawer.

4. If gasket is not sealed, open drawer and slightly loosen

four drawer screws (two on each side) to allow drawer

to rotate.

5. Close drawer and recheck the seal on the gasket (A).

Open the drawer grabbing by the sides in the center

(B). Be careful not to rotate the drawer.

6. Tighten four drawer screws.

7. Recheck gasket seal.

8. Install the toe grille by tting into place.

A

B

Assembly

Fully extend

drawer slides

Cabinet

Slot

Install

screws

(2) each

side

Push

against

freezer

drawer

Grab drawer

at center

from both

sides, then

pull drawer out

Do not remove

other screws

Remove hex

head drawer

screw

Remove

hex

head drawer

screw

Remove

hex

head drawer

screw

Remove hex

head drawer

screw

Figure 26

Figure 27

Figure 25

Figure 24

13

CONNECTING THE WATER SUPPLY

!

CAUTION

NOTE

Check with your local building authority for recommendations on

water lines and associated materials prior to installing your new

refrigerator.

Ensure that your water supply line connections comply with all

local plumbing codes.

To Avoid Property Damage:

• Copper or Stainless Steel braided tubing is recommended

for the water supply line. Water supply tubing made of ¼ inch

plastic is not recommended to be used. Plastic tubing greatly

increases the potential for water leaks, and the manufactur-

er will not be responsible for any damage if plastic tubing is

used for the supply line.

• DO NOT install water supply tubing in areas where tempera-

tures fall below freezing.

• Chemicals from a malfunctioning softener can damage the

ice maker. If the ice maker is connected to soft water, ensure

that the softener is maintained and working properly.

!

WARNING

To avoid electric shock, which can cause death or severe

personal injury, disconnect the refrigerator from electrical

power before connecting a water supply line to the refriger-

ator.

To Connect Water Supply Line To Ice Maker Inlet Valve

1. Disconnect refrigerator from electric power source.

2. Place end of water supply line into sink or bucket. Turn ON

water supply and ush supply line until water is clear. Turn

OFF water supply at shutoff valve.

3. Remove plastic cap from water valve inlet and discard cap.

4. If you use copper tubing - Slide brass compression nut,

then ferrule (sleeve) onto water supply line. Push water sup-

ply line into water valve inlet as far as it will go (¼ inch / 6.4

mm). Slide ferrule (sleeve) into valve inlet and nger tighten

compression nut onto valve. Tighten another half turn with a

wrench; DO NOT over tighten. See Figure 28.

If you use stainless steel tubing - The nut and ferrule are

already assembled on the tubing. Slide compression nut onto

valve inlet and nger tighten compression nut onto valve.

Tighten another half turn with a wrench; DO NOT over

tighten. See Figure 29.

5. With steel clamp and screw, secure water supply line (copper

tubing only) to rear panel of refrigerator as shown.

6. Coil excess water supply line (copper tubing only), about 2½

turns, behind refrigerator as shown and arrange coils so they

do not vibrate or wear against any other surface.

7. Turn ON water supply at shutoff valve and tighten any con-

nections that leak.

8. Reconnect refrigerator to electrical power source.

9. To turn ice maker on, lower wire signal arm (freezer ice

maker) or set the ice maker’s On/Off power switch to the “On”

position (fresh food ice maker).

Before Installing The Water Supply Line, You Will Need:

• Basic Tools: adjustable wrench, at-blade screwdriver, and

Phillips™ screwdriver

• Access to a household cold water line with water pressure

between 30 and 100 psi.

• A water supply line made of ¼ inch (6.4 mm) OD, copper

or stainless steel tubing. To determine the length of tubing

needed, measure the distance from the ice maker inlet valve

at the back of the refrigerator to your cold water pipe. Then

add approximately 7 feet (2.1 meters), so the refrigerator can

be moved out for cleaning (as shown).

• A shutoff valve to connect the water supply line to your

household water system. DO NOT use a self-piercing type

shutoff valve.

• Do not reuse compression tting or use thread seal tape.

• A compression nut and ferrule (sleeve) for connecting a cop-

per water supply line to the ice maker inlet valve.

Plastic water tubing

to ice maker

ll tube

Plastic water tubing

to ice maker

ll tube

Steel

clamp

Steel

clamp

Brass

compression

nut

Ferrule

(sleeve)

Copper

water

line

Water valve

bracket

Water valve

bracket

Valve inlet

Water valve

Copper water line

from household

water supply

Stainless

steel

water line

6 ft. stainless steel water

line from household water

supply

Figure 28 Figure 29

14

NOTE

ELECTRONIC CONTROL

A red indicator light will be illuminated above most active features.

Touch the icon to activate the options below.

fast freeze Activates a faster rate for freezing food.

fast ice Increases the production of ice

energy saver Keep this switch set on energy saver (light on) for lowest energy us

age. If moisture appears on the cabinet between the doors, pressing

this button will turn the light off and enable an electric heater used to

reduce moisture on the cabinet between the doors.

water lter Press and hold for three seconds to reset after lter change.

air lter Filter condition status is always displayed when door is open. Press

and hold for three seconds to reset after lter change.

temp mode Touch to toggle display from Fahrenheit to Celsius.

mute sounds Tones emitted by each key press can be turned off based on user

preference. The sounds are muted when the red indicator is lit. Warn-

ing signals will stay active.

default settings Resets all refrigerator settings such as temp, temp display and tones

to their factory default settings.

on off Press and hold for three seconds to turn off the cooling system to

clean the refrigerator. It also turns off the ice maker. The temperature

displays will read OFF.

Pressing the system on/off icon does not

turn off power to your refrigerator. You must

unplug the power cord from the wall outlet.

Setting cooling temperatures

Press the + or – indicator to adjust the temperature to the desired setting.

The temperature display will begin to blink with the rst touch. The display will time out

after 10 seconds and return to the basic display.

Alarms

Door Ajar If the door has been left open for an extended period of time, an alarm

will sound and the door ajar indicator will display on the bottom display

of the control panel. The alarm is turned off by closing the door. The

mute sounds key will blink to prompt the reset of any active alarms.

Press this key to reset any system alarms.

High Temp In the event of a high temperature condition, the temperature display

will blink and display “HI”. After 20 minutes, the alarm will sound and

the high temp indicator will be red on the bottom of the control panel.

The mute sounds icon will illuminate until pressed, acknowledging the

alarm, at which time the highest temperature reached will be displayed

and the refrigerator will resume normal operation. In case the high temp

alarm is not acknowledged at the rst alarm sound time out, when the

door is rst opened, the alarm sound will be repeated.

Power fail In the event of a power failure, the power fail alert will be displayed and

the temperature display will blink until the mute sounds icon is pressed,

acknowledging the alarm. Other modes may be turned off until the alarm

is acknowledged. The power fail alert is turned off and the refrigerator

will resume normal operation. The high temp alarm may also be illumi

nated until a safe operating range temperature has been reached.

LED COLORS / Assembly

Figure 30

15

ELECTRONIC CONTROL

Sabbath mode

The Sabbath Mode is a feature that disables portions

of the refrigerator and its controls for, in accordance with

observance of the weekly Sabbath and religious holidays

within the Orthodox Jewish community.

Sabbath Mode is turned ON and OFF by pressing and

holding the freezer temp “-” and the refrigerator temp “+”

indicators for ve seconds. The display shows “Sb” while in

Sabbath mode.

In the Sabbath Mode, the High Temp alarm is active for

health reasons. If a high temperature alarm is activated

during this time, for example due to a door left ajar, the

alarm will sound intermittently for about two minutes. The

alarm will then silence on its own and a red high tempera-

ture icon will display. The high temp icon will continue to

display, even if the door is closed, until the Sabbath mode

is exited and the icon reset. The refrigerator will function

normally once the door is closed, without any violation of

the Sabbath/Holidays.

NOTE

While in Sabbath Mode, neither the lights nor the control

panel will work until Sabbath Mode is deactivated. Refrig-

erator stays in Sabbath Mode after power failure recovery.

It must be deactivated with the buttons on the control panel.

During Sabbath Mode, the ice maker is turned off by main

control board.

Sabbath Mode and the Select Temp

Drawer

The Select Temp Drawer should be turned off for the

Sabbath/Holidays. Before putting the refrigerator into the

Sabbath mode, turn the Select Temp Drawer off by press-

ing the drawer on/off button. The display will show “OFF”

and the drawer will turn off. Then enter the Sabbath mode

function on the main refrigerator display. See the electronic

control “Sabbath Mode” section. When in Sabbath mode,

the display will not illuminate and the drawer will remain

off. The drawer can still be used as a non-temp controlled

drawer in this mode. When the refrigerator is taken out of

Sabbath mode, the Select Temp Drawer will have to be

turned back on.

If the Select Temp Drawer is not turned off prior to putting

the unit into Sabbath Mode, it will continue to adjust itself to

maintain the set point even if the display does not illuminate

to show that it is still on.

16

AUTOMATIC ICE MAKER

On

Off

Ice maker operation & care

After the refrigerator is installed properly, the ice maker can

produce ice within 24 hours. It can completely ll an ice bin

in about three days.

When using the ice maker for the rst time and in order

for the ice maker to work properly, it is necessary to clear

air from water lter tubing. Once ice maker begins making

ice, allow the bucket to ll completely, then discard the rst

TWO FULL buckets of ice. It will take at least two days to

completely ll the bucket on regular ice making mode or 1½

days on fast ice mode.

The ice maker produces approximately four pounds of ice

every 24 hours depending on usage conditions.

NOTE

Your ice maker is turned on at the factory so it can work as

soon as you install your refrigerator. If you cannot connect

a water supply, lift the ice maker’s wire signal arm to turn it

off. Otherwise, the ice maker’s ll valve may make a loud

chattering noise when it attempts to operate without water.

Turning the ice maker on and off

Ice production is controlled by lifting/lowering the ice mak-

er’s wire signal arm. To gain access to the ice maker, pull

the freezer drawer out. Lift the wire signal arm to turn the

ice maker OFF and lower the wire signal arm to turn it ON.

Wire

signal arm

Ice maker tips

• If your refrigerator is not connected to a water supply or

the water supply is turned off, turn off the ice maker by

lifting wire signal arm.

• Ice cubes stored too long may develop an odd avor.

Empty the ice bin as explained below.

• The following sounds are normal when the ice maker is

operating:

- Motor running

- Ice dropping into ice bin

- Water valve opening or closing

- Running water

Fast Ice Function

Your refrigerator is equipped with a Fast Ice Function, that

will, if activated at your user interface, allow an increase in

ice production. You do not need to deactivate it, if not need-

ed, your refrigerator will operate on normal conditions.

!

CAUTION

If the water supply to your refrigerator is softened, be sure

the softener is properly maintained. Chemicals from a water

softener can damage the ice maker.

Cleaning the ice maker

Clean the ice maker and ice bin at regular intervals, espe-

cially prior to vacation or moving.

1. Turn off the ice maker.

2. Remove the ice bin.

3. Empty and carefully clean the ice bin with mild deter-

gent. Do not use harsh or abrasive cleaners. Rinse with

clean water.

4. Allow the ice bin to dry completely before replacing in

the freezer.

5. Replace the ice bin. Turn the ice maker on.

Remove and empty the ice bin if:

• An extended power failure (one hour or longe)

causes ice cubes in the ice bin to melt and freeze

together.

Remove the ice bin and shake to loosen the cubes or clean

as explained above.

!

CAUTION

NEVER use an ice pick or similar sharp instrument to break

up the ice. This could damage the ice bin. To loosen stuck

ice, use warm water. Before replacing the ice bin, make

sure it is completely dry.

Figure 31

17

!

CAUTION

To avoid injury from breakage, handle tempered glass

shelves carefully.

Your refrigerator includes glass shelves that are designed

to catch and hold accidental spills.

You can easily adjust shelf positions in the fresh food com-

partments to suit your needs. The shelves have mounting

brackets that attach to slotted supports at the rear of each

compartment.

To change the position of a shelf:

1. Before adjusting a shelf, remove all food.

2. Lift the front edge up and pull the shelf out.

3. Replace by inserting the mounting bracket hooks into

the desired support slots.

4. Lower the shelf and lock into position.

Shelf features Drawers

Your refrigerator includes a variety of storage drawers.

These drawers are located in xed positions at the bottom

of the fresh food compartment.

Crispers

Crisper drawers are designed for storing fruits, vegetables,

and other fresh produce.

Crisper humidity control

Crisper drawers include a sliding control for adjusting the

humidity inside the crisper. Leafy vegetables keep best

when stored with the Humidity Control set on Higher Hu-

midity. Fresh fruits keep best when stored with the Humidity

Control set on Lower Humidity.

STORAGE FEATURES

or

Opening crisper drawer

Humidity control

Higher

humidity

Lower

humidity

Adjusting crisper humidity

Figure 32

Figure 34

Figure 35

Figure 33

18

STORAGE FEATURES

Opening the drawer

To operate:

1. To turn on and off, press the drawer’s On/Off button.

The numeric display will show a temperature between

“28°F and 42°F” when on and “OFF” when off.

2. Press F/C if you prefer to display Fahrenheit “F,” or

Celsius “C”.

3. Press either the up or down scroll buttons to illu-

minate the desired item.

4. Once an option is selected, the drawer will adjust and

maintain the temperature for the setting selected.

5. When turned off, the Select Temp Drawer functions

as a standard meat pan. The Select Temp Drawer is

best used for packaged food products. Leafy vegeta-

bles and unpackaged fruits are best kept in one of the

crisper drawers.

6. The three favorite selections provide exibility to set

and store personal temperature selections. The tem-

perature is adjusted up by pressing the + or – buttons.

The drawer will store the selected temperature setting

until it is changed.

7. 7 The control buttons can be locked to prevent acciden-

tal changes by pressing the control lock button for three

seconds. Deactivate by pressing for three seconds

again.

<

To remove

the crisper

drawer for

cleaning:

1. Pull the

drawer out

until it stops.

2. Lift the

front slightly

and remove

the drawer.

Special

items rack

The innova-

tive design of

the special

items rack

allows you to

store 4 bot-

tles of wine

or soft drink

bottles.

Cool zone

Some models are equipped with a meat keeper drawer for

short-term storage of bulk meat items. This drawer includes

sliding controls for adjusting the humidity inside. Any meat

to be kept longer than two days should be frozen. If you

store fruits or vegetables in this drawer, set it to a higher

humidity.

Removing crisper

drawer

Special items

rack

Figure 36

Figure 37

Figure 38

Figure 39

19

Adjustable Door Bin

NOTE

!

CAUTION

NOTE

STORAGE FEATURES

DO NOT clean the display area of the Select Temp

Drawer with abrasive or caustic cleaners. Wipe clean

with a moist sponge.

The Select Temp Drawer and cover can be removed for

cleaning but the control unit, attached to the right side of

the fridge, cannot be removed. Do not immerse the Select

Temp Drawer cover in water or put it in a dishwasher.

Clean with a damp cloth or sponge.

To remove the Select Temp Drawer for cleaning:

1. Pull the drawer out until it stops.

2. Lift the front slightly and remove the drawer.

Removing the drawer

When the refrigerator is turned off by pressing the main

electronic control on/off button, the Select Temp Drawer will

also be turned off. When the refrigerator is turned back on,

the Select Temp Drawer will resume operations at the temp

setting that was set before the refrigerator was turned off.

Doors

Storage bins

The doors to your fresh food compartment use a system of

modular storage bins. All of these bins are removable for

easy cleaning. Some of them have xed positions, while

others can be adjusted to your needs.

Door bins are ideal for storing jars, bottles, cans, and large

drink containers. They also enable quick selection of fre-

quently used items.

Covered door bin

Lock

Tilt can bin

Covered Door Bin

Use the covered door bin, at the top of the fresh food com-

partment door, for short-term storage of cheese, spreads,

or butter. The covered door bin is designed to be warmer

than the open area and includes a lift-up cover that may be

locked and a dairy divider (select models).

Accesorries

Tilt can bins

The can bins allow you to efciently and securely store up

to eight 12-ounce canned beverages.

To change the position of an adjustable door bin:

1. Before adjusting a bin, remove all food.

2. Grip the bin rmly with both hands and lift it upward.

3. Remove the bin.

4. Place the bin just above desired position.

5. Lower the bin onto supports until locked in place.

Figure 40

Figure 41

Figure 42

Figure 43

20

STORAGE FEATURES

Freezer Features

Stabilizer bar

Basket

retainer

clips

To Remove Upper Basket

1. Remove all items from basket.

2. Remove basket by pulling basket out to its full exten-

sion and lift out.

To reinstall upper basket, position basket onto the retainer

clips making sure the front of the basket rests in the retain-

er clips on the stabilizer bar.

Two freezer baskets

NOTE

If basket is not resting on stabilizer bar retainer clips, the

drawer will not close properly.

Removing lower basket

Basket

retainer

To Remove Lower Basket

1. Remove all items from basket.

2. Remove the basket by tilting it forward and lifting it from

the retainer clips.

Spill Guard Tray should be hand washed in warm water.

Lower basket divider and

spill guard tray

Lower basket

divider

Spill guard

tray

Lift up on the rear of the lower divider and pull out.

Upper basket divider

Middle basket

divider

Retainers

Stabilizer

bar

Lift up on the rear of the lower divider and pull out.

Tilt Wire Shelf

The freezer tilt wire shelf (located on the inside of the freez-

er drawer) is not designed to be removed.

Dividers Removal

Lift up on the front of the upper divider and pull out.

Figure 44

Figure 45

Figure 47

Figure 46

La page charge ...

Heartland HCFDR23CBL Le manuel du propriétaire

Ce manuel convient également à

Heartland HCFDR23CBL Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents