Marvel MP24WDG5RS Mode d'emploi

Marque: Marvel

Modèle: MP24WDG5RS

Catégorie: Boissons glacées

Taper: Mode d'emploi

MP15WSG4**

MP15WSF4**

MP24WSG5**

MP24WSF5**

MP24WDG5**

MP24WDF5**

MP24WSG0**

Note: Wine refrigerators / coolers are designed exclusively

for the storage of wine. Wine refrigerators / coolers cannot

attain storage temperatures suitable for fresh food storage.

Remarque : Les réfrigérateur sont conçues exclusivement

pour y garder des vins. Elles ne peuvent pas atteindre des

températures de conservation convenant à l’entreposage

d’aliments frais.

EN Installation, Operation and Maintenance Instructions

FR Instructions d’installation, d’utilisation et d’entretien

Built in Wine Refrigerator / Cooler

Le vin réfrigérateur intégrées

NOTE

CAUTION

Contents:

Safety information ...............................................................2

Unpacking your appliance ..................................................3

Warranty registration .....................................................3

Installing your appliance ......................................................4

Cabinet clearances .........................................................4

Leveling the appliance ....................................................4

Electrical connection ......................................................5

Product dimensions ............................................................6

Using your Electronic control .............................................8

Starting your appliance ...................................................8

Sleep mode ....................................................................8

Turning your appliance "ON" or "OFF" ...........................8

Adjusting the temperature ..............................................8

Interior display lighting ....................................................9

Temperature mode .........................................................9

Control lock ....................................................................10

Temperature sensor error codes ...................................10

Alarms ...........................................................................10

Door ajar ..................................................................10

Power failure .............................................................11

Temperature alarm ....................................................11

Vacation mode ..............................................................11

Overlay door panel installation ........................................12

Shelving congurations ....................................................18

Care and cleaning .............................................................20

Energy saving tips ............................................................20

Obtaining service .............................................................21

Troubleshooting ................................................................22

Warranty ...........................................................................23

WARNING

State of California Proposition 65 Warning:

This product contains one or more chemicals known

to the State of California to cause cancer.

WARNING

State of California Proposition 65 Warning:

This product contains one or more chemicals known

to the State of California to cause birth defects or

other reproductive harm..

CONTENTS

Important Safety Instructions

Warnings and safety instructions appearing in this guide

are not meant to cover all possible conditions and situa-

tions that may occur. Common sense, caution, and care

must be exercised when installing, maintaining, or operat-

ing this appliance.

Recognize Safety Symbols,

Words, and Labels.

CAUTION-Hazards or unsafe practices which could re-

sult in personal injury or property / product damage.

NOTE-Important information to help assure a problem

free installation and operation.

WARNING

WARNING - You can be killed or seriously injured

if you do not follow these instructions.

NOTE

CAUTION

XXXXXXXXXXXX

WARNING

WARNING - Help Prevent Tragedies

Child entrapment and suffocation are not problems of

the past. Junked or abandoned refrigerators are still

dangerous - even if they sit out for "just a few hours".

If you are getting rid of your old refrigerator, please

follow the instructions below to help prevent acci-

dents.

Before you throw away your old refrigerator or

freezer:

• Take off the doors or remove the drawers.

• Leave the shelves in place so children may not

easily climb inside.

WARNING

WARNING - Dispose of the plastic bags which can

be a suffocation hazard.

MARVEL

If the appliance was shipped, handled, or stored in other

than an upright position for any period of time, allow the ap-

pliance to sit upright for a period of at least 24 hours before

plugging in. This will assure oil returns to the compressor.

Plugging the appliance in immediately may cause damage

to internal parts.

Figure 1

It is important you send in your warranty registration card

immediately after taking delivery of your appliance or you

can register online at www.marvelrefrigeration.com.

The following information will

be required when registering

your appliance.

Service Number

Serial Number

Date of Purchase

Dealer’s name and address

The service number and serial number can be found on the

serial plate which is located inside the cabinet on the left

side near the top. (See gure 1).

Warranty Registration

UNPACKING YOUR APPLIANCE

Remove Interior Packaging

Your appliance has been packed for shipment with all parts

that could be damaged by movement securely fastened.

Remove internal packing materials and any tape holding in-

ternal components in place. The owners manual is shipped

inside the product in a plastic bag along with the warranty

registration card, and other accessory items.

Important

Keep your carton and packaging until your appliance has

been thoroughly inspected and found to be in good condi-

tion. If there is damage, the packaging will be needed as

proof of damage in transit. Afterwards please dispose of all

items responsibly.

Note to Customer

This merchandise was carefully packed and thoroughly

inspected before leaving our plant. Responsibility for its

safe delivery was assumed by the retailer upon acceptance

of the shipment. Claims for loss or damage sustained in

transit must be made to the retailer.

DO NOT RETURN DAMAGED MERCHANDISE TO THE

MANUFACTURER - FILE THE CLAIM WITH THE

RETAILER.

Online registra-

tion available at

www.marvelrefrig-

eration.com

WARNING

EXCESSIVE WEIGHT HAZARD

Use two or more people to move product.

Failure to do so can result in personal injury.

CAUTION

WARNING

INSTALLING YOUR APPLIANCE

Select Location

The proper location will ensure peak performance of your

appliance. We recommend a location where the unit will

be out of direct sunlight and away from heat sources. To

ensure your product performs to specications, the recom-

mended installation location temperature range is from 55

to 100°F (13 to 38°C).

Cabinet Clearance

Ventilation is required from the bottom front of the appli-

ance. Keep this area open and clear of any obstructions.

Adjacent cabinets and counter top can be installed around

the appliance as long as the front grille remains unob-

structed. Overlay door models with articulated hinges are

intended for built-in applications only.

Front Grille

Do not obstruct the front grille. The openings within the

front grille allow air to ow through the condenser heat ex-

changer. Restrictions to this air ow will result in increased

energy usage and loss of cooling capacity. For this reason

it is important this area not be obstructed and the grille

openings kept clean. Marvel does not recommend the use

of a custom made grille as air ow may be restricted. (See

Figure 2).

Leveling Legs

Adjustable legs at the front and rear corners of the appli-

ance should be set so the unit is rmly positioned on the

oor and level from side to side and front to back. The over-

all height of your Marvel appliance may be adjusted higher

(by turning the leveling leg out, CCW) and lower (by turning

the leveling leg in, CW) dimensions as shown in Table "A".

To adjust the leveling legs, place the appliance on a solid

surface and protect the oor beneath the legs to avoid

scratching the oor. With the assistance of another person,

lean the appliance back to access the front leveling legs.

Raise or lower the legs to the required dimension by turning

the legs. Repeat this process for the rear by tilting the appli-

ance forward using caution. On a level surface check the

appliance for levelness and adjust accordingly.

The front grille screws may be loosened and the grille ad-

justed to the desired height. When adjustment is complete

tighten the two front grille screws. (See Figure 5).

An optional stacking kit, shown in is required to stack

products. Failure to use a stacking kit could result in

personal injury. Contact your dealer or Marvel customer

service at 800-223-3900 to order.

Figure 2

Front Leveling

Legs

Front Grille,

keep this area

open.

Rear

Leveling

Legs

Model Door Style

Minimum

Height

Maximum

Height

MP(15)(24)* (G)

34"

(86.4 cm)

35"

(88.9 cm)

MP(15)(24)* (F)

34"

(86.4 cm)

35"

(88.9 cm)

Table A

NOTE

Electrical Shock Hazard

• Do not use an extension cord with this appliance.

They can be hazardous and can degrade product

performance.

• This appliance should not, under any circumstanc-

es, be installed to an un-grounded electrical supply.

• Do not remove the grounding prong from the power

cord. (See Figure 3).

• Do not use an adapter. (See Figure 4).

• Do not splash or spray water from a hose on the

appliance. Doing so may cause an electrical shock,

which may result in severe injury or death.

WARNING

Ground Fault Circuit Interrupters (GFCI) are prone to nui-

sance tripping which will cause the appliance to shut down.

GFCI’s are generally not used on circuits with power equip-

ment that must run unattended for long periods of time, un-

less required to meet local building codes and ordinances.

Electrical Connection

A grounded 115 volt, 15 amp dedicated circuit is required.

This product is factory equipped with a power supply

cord that has a three-pronged, grounded plug. It must be

plugged into a mating grounding type receptacle in accor-

dance with the National Electrical Code and applicable lo-

cal codes and ordinances (see Figure 6). If the circuit does

not have a grounding type receptacle, it is the responsibility

and obligation of the customer to provide the proper power

supply. The third ground prong should not, under any cir-

cumstances, be cut or removed.

Figure 6

INSTALLING YOUR APPLIANCE

Figure 5

Front grille screw

Front grille

Figure 3

Figure 4

Do not remove

ground prong

DOOR STYLE

(G) Glass Frame Door

(F) Frame Glass Overlay Door (no handle)

PRODUCT DIMENSIONS

Figure 7a

ROUGH-IN OPENING DIMENSIONS CABINET DIMENSIONS

MODEL "A" "B" "C" "D" "E" "F" "G" "H" "J"

MP15WSG

15"

(38.1 cm)

**34

⁄4" to 35

⁄4"

(87 to 89.5 cm)

24"

(61 cm)

⁄8"

(37.8 cm)

34" to 35"

(86.4 to 88.9 cm)

⁄32"

(60.2 cm)

⁄32"

(66.6 cm)

⁄32"

(95 cm)

⁄16"

(44.3 cm)

MP15WSF

15"

(38.1 cm)

**34

⁄4" to 35

⁄4"

(87 to 89.5 cm)

*24"

(61 cm)

⁄8"

(37.8 cm)

34" to 35"

(86.4 to 88.9 cm)

⁄8"

(58.1 cm)

⁄2"

(95.2 cm)

⁄8"

(35.9 cm)

MP24**G

24"

(61 cm)

**34

⁄4" to 35

⁄4"

(87 to 89.5 cm)

24"

(61 cm)

⁄8"

(60.7 cm)

34" to 35"

(86.4 to 88.9 cm)

⁄32"

(60.2 cm)

⁄32"

(66.6 cm)

⁄32"

(117.9 cm)

⁄16"

(67.2 cm)

MP24**F

24"

(61 cm)

**34

⁄4" to 35

⁄4"

(87 to 89.5 cm)

*24"

(61 cm)

⁄8"

(60.7 cm)

34" to 35"

(86.4 to 88.9 cm)

⁄8"

(58.1 cm)

⁄2"

(118.1 cm)

⁄8"

(58.7 cm)

MP24WSG0

24"

(61 cm)

**34" to 35"

(86.4 to 88.9 cm)

24"

(61 cm)

⁄8"

(60.7 cm)

⁄4" to 34

⁄4"

(85.7 to 88.3 cm)

⁄32"

(60.2 cm)

⁄32"

(66.6 cm)

⁄32"

(117.9 cm)

267⁄16"

(67.2 cm)

If necessary to gain clearance inside the rough-in

opening a hole can be cut through the adjacent cabi-

net and the power cord routed through this hole to a

power outlet. Another way to increase the available

opening depth is to recess the power outlet into the

rear wall to gain the thickness of the power cord plug.

Not all recessed outlet boxes will work for this applica-

tion as they are too narrow, but a recessed outlet box

equivalent to Arlington #DVFR1W is recommended for

this application, (see Figure 8).

Figure 8

"A"

"B"

"C"

"D"

"E"

Figure 7

(G) Glass door

shown

"F"

"D"

"E"

"H"

"J"

"G"

PRODUCT DIMENSIONS

⁄2"

(54.6 cm)

(2.5 cm)

Figure 9

PRODUCT DATA

MODEL

ELECTRICAL

REQUIREMENTS #

PRODUCT

WEIGHT

MP15WSG 115V/60Hz/15A

105 lbs

(47.6 kg)

MP15WSF 115V/60Hz/15A

105 lbs

(47.6 kg)

MP24**G 115V/60Hz/15A

140 lbs

(63.6 kg)

MP24**F 115V/60Hz/15A

140 lbs

(63.6 kg)

* To install (F) models with the door face ush with adja-

cent cabinetry doors, custom decorative panel thickness

cannot exceed

⁄4" (19 mm).

** Minimum rough-in opening required is to be larger than

the adjusted height of the cabinet.

# A grounded 15 amp dedicated circuit is required. Follow

all local building codes when installing electrical and appli-

ance.

APPLIES TO THE FOLLOWING MARVEL MODELS

MP15WS MP24WS

MP24WD

NOTE

Power Failure

ALARM RESET

USING YOUR ELECTRONIC CONTROL

Upper/Lower

zones

(Dual Zone

models only)

System Status

indicators

Starting your appliance (Single and Dual

Zone:

Plug the appliance power cord into a 115 volt wall outlet.

Your appliance is shipped from the factory in the "On" posi-

tion and will begin start-up of cooling as soon as power is

supplied. If the appliance does not start, conrm that the

wall outlet has power, and that the control is in the "On"

position, (See "Turning your appliance On and Off" below).

The control display is covered with a clear plastic lm. This

lm may be removed by carefully lifting the lm at a corner.

On initial power up, the control display will indicate a

"Power Failure" alarm. This is a normal condition as the ap-

pliance was powered-up at the factory for quality inspection

and then removed from power. A momentary press of the

"On/Off" keypad will reset this alarm condition. (See Alarms

section on page 10).

Turning your appliance ON and OFF (Single

and Dual Zone):

If the appliance is "On", (and out of sleep mode) the tem-

perature will be shown in the display area of the control.

To turn the appliance "Off", press and hold the "On/Off"

keypad for 4-seconds. "OFF" will now be displayed on the

control.

To turn the appliance "On", press and hold the "On/Off"

keypad for 4-seconds.

Sleep mode (Single and Dual Zone):

If no keypads are pressed for 60 seconds, the display will

enter sleep mode to conserve power. The control panel will

go dark with the exception of the system status "OK" indi-

cator which will remain enabled. Alarm conditions will wake

the display, (see alarms on page 10).

To make the following changes to the control settings

(turning the appliance ON/OFF, adjusting the tempera-

ture, changing the interior lights, and activating vaca-

tion mode), the control must be awake.

To wake the display press any keypad. A conrm tone will

sound, and the current storage compartment temperature

will be displayed.

The sleep mode can be disabled if you prefer to have the

display on continuously. Press and hold the "Lock" key-

pad until the display goes past "Loc" and reads "nSL". To

enable the sleep mode, repeat the instruction, again going

past "Loc" until the display reads "SLP".

Figure 10

Electronic control

Temp

Minus

keypad

On/Off

keypad

Temp

Plus

keypad

Display Area

Lights

keypad

Lock

keypad

Adjusting the temperature:

When initially loading your product with warm contents, it

may take up to 48-hours for the storage compartment tem-

perature to stabilize.

When making temperature set-point changes, it may take

up to 24-hours for the stored contents to stabilize at your

new set-point temperature.

USING YOUR ELECTRONIC CONTROL

Factors that affect the storage compartment stabilized

temperature:

• Changes to temperature setting.

• Room temperature changes.

• Temperature of stored contents.

- Loading warm contents.

- Cold content load will delay the change to a warmer

set-point temperature.

- Warm content load will delay the change to a colder

set-point temperature.

• Usage, (number and duration of the door openings).

• Use of the storage compartment display lighting, (glass

door product only).

• Installation of the appliance in direct sunlight or next to

a heat source.

Interior lighting (Single and Dual Zone):

Display lighting :

Display lighting is intended for glass door models only, to

illuminate the interior with the door closed.

With the control out of sleep mode press the "Light" keypad

once to activate the interior lighting display feature at full

illumination. A conrmation tone will sound, and the light

bulb "Icon" will illuminate. Pressing the "Light" keypad a

2nd time will dim the lighting to 50%. A 3rd press will deacti-

vate the display lighting feature. The display lighting will

automatically deactivate after 4-hours.

If you have a solid door/drawer product the display lighting

function is only used to select the color of the interior light.

Single Zone Models:

To set or check the set-point temperature (with the control

out of sleep mode), press the "-" or "+" keypads. "SET" will

be indicated on the user interface panel and the current

set-point temperature will display and ash. Subsequent

presses of the "-" or "+" keypads will adjust the temperature

colder or warmer respectively. When you have reached

your desired set-point temperature, press the "On/Off" key-

pad to accept, or do nothing and the "Set" mode will time-

out in 10-seconds accepting the displayed temperature as

the new set-point.

The available set-point temperature range for your appli-

ance is 40°F (4.5°C) to 65°F (18.4°C). If you attempt to

adjust the temperature outside of this range you will receive

an audible notication.

will adjust the temperature colder or warmer respectively.

When you have reached your desired set-point tempera-

ture, press the "On/Off" keypad to accept, or do nothing

and the "Set" mode will time-out in 10-seconds accepting

the displayed temperature as the new set-point.

The available set-point temperature range for your appli-

ance is 45°F (7.3°C) to 55°F (12.9°C) for the lower zone

and 55°F (12.9°C) to 62°F (16.8°C) for the upper zone.

If you attempt to adjust the temperature outside of these

ranges you will receive an audible notication.

Lower zone

selected

Upper zone

selected

Dual Zone Models:

Temperatures can be set for each individual zone (upper

and lower) in the dual zone wine cellar. To do so you must

rst select the zone you want to set the temperature for.

You do so by pressing the upper or lower button on the

display. When pressed the LED light will be illuminated for

the respective display.

Changing the Tri-Color lighting:

To change the color between white, amber, or blue, with the

control out of sleep mode, momentarily press the "Light"

keypad. The keypad will illuminate. Then press and hold

the keypad for approximately 3 seconds the interior light

will start to cycle through the 3 available colors. On solid

door/drawer product this will need to be done with the door/

drawer open to be able to observe the colors. Release the

keypad when the desired color is on, and your interior light

will be changed to that color. After selection of color for

solid door/drawer product, the display light feature should

be turned-off, ("Light" keypad not illuminated).

Temperature mode (Single and Dual Zone):

The temperature mode is preset from the factory in Fahren-

heit (°F) but you have the option to change it to Centigrade

(°C). To change the mode, press and hold the "-" keypad,

while pressing the "+" keypad, then release the "-" keypad.

The temperature will now be displayed in Centigrade (°C).

Repeat the procedure to change the temperature mode

back to Fahrenheit (°F).

To change the set temperature for a particular zone, with

the zone selected and out of sleep mode, press the "-" or

"+" keypads. "SET" will be indicated on the user interface

panel and the current set-point temperature will display

and ash. Subsequent presses of the "-" or "+" keypads

Door Ajar

ALARM RESET

Control lock (Single and Dual Zone):

The control panel can be locked to avoid unintentional

changes. To lock the control, press and hold the "Lock" key-

pad until the display reads "Loc" then immediately release

your nger from the keypad. The lock icon will ash 3-times

and then continuously illuminate. When the control panel is

locked, only the Lock keypad, System Status OK indicator

, and the Alarm indicator are active. To un-lock the control

panel, repeat this instruction until the display reads "nLc"

then immediately release your nger from the keypad.

Alarms (Single and Dual Zone):

The control will alert you to conditions that could adversely

affect the performance of the appliance.

• Door ajar - If the door is open, or not closed prop-

erly, for more than 5-minutes the System Status OK

indicator will turn-off, the "Door Ajar" indicator will ash,

and a tone will sound every 60 seconds. Additionally,

an "ALARM RESET" indicator will be displayed below

the "On/Off" keypad.

USING YOUR ELECTRONIC CONTROL

NOTE

If the control lock is active (illuminated lock icon) the control

will have to be unlocked before using the keypad to reset

an alarm condition. See page 10 (Control Lock) for instruc-

tions for unlocking the control.

The temperature sensors are monitored continuously. Any

OPEN or SHORTED circuit condition will initiate an

ERROR CODE as listed below:

Temperature Sensor Error Codes

Sensor Displayed Code Error Description Action to Take

Single Zone

Temperature Sensor

Failed temperature sensor in the single

zone compartment. Can lead to unwant-

ed wine storage temperatures.

Call service to have the tem-

perature sensor replaced.

Defrost Sensor

Failed defrost temperature sensor.

Causes unit to not defrost properly and

can create large frost build-up. Can lead

to water damage to the unit and sur-

rounding oor.

Unplug the power cord imme-

diately and call service to have

the defrost sensor replaced.

Single Zone Models:

Dual Zone Models:

Temperature Sensor Error Codes

Sensor Displayed Code Error Description Action to Take

Upper Zone

Temperature Sensor

Failed temperature sensor in the upper

zone compartment. Can lead to unwant-

ed wine storage temperatures.

Call service to have the tem-

perature sensor replaced.

Lower Zone

Temperature Sensor

Failed temperature sensor in the lower

zone compartment. Can lead to unwant-

ed wine storage temperatures.

Call service to have the tem-

perature sensor replaced.

Defrost Sensor

Failed defrost temperature sensor.

Causes unit to not defrost properly and

can create large frost build-up. Can lead

to water damage to the unit and sur-

rounding oor.

Unplug the power cord imme-

diately and call service to have

the defrost sensor replaced.

Temperature Sensor Error Codes

This alarm condition can be reset by closing the door

or momentarily pressing the "On/Off" keypad, (i.e.-if

you are cleaning the storage compartment, etc.). The

alarm will recur in 5-minutes if the alarm condition

persists.

NOTE

The audible alarm can be muted, for each occurrence,

by pressing the lock keypad.

ALARM RESET

Power Failure

ALARM RESET

Temp

NOTE

Door Ajar

Temp

• Power failure - If power to the appliance is inter-

rupted the System Status indicator will turn-off and

the "Power Failure" indicator will ash. Additionally, an

"ALARM RESET" indicator will be displayed below the

"On/Off" keypad. No audible tone will sound. This alarm

condition can be reset by momentarily pressing the

"On/Off" keypad. If this alarm occurs, it is recommend-

ed that you check the condition of any perishables,

even if the appliance is operating normally and the tem-

perature has recovered, as prolonged power outages

could result in excessive temperature excursions which

may spoil perishables.

• Temperature alarm - If the storage compart-

ment temperature deviates excessively from your

set-point temperature for an extended period of time,

the "TEMP" indicator will ash, and an audible tone

will sound every 60 seconds. Additionally, an "ALARM

RESET" indicator will be displayed below the "ON/

OFF" keypad.

Multiple alarms are possible, i.e.- "Door Ajar" for a pro-

longed period may trigger a "Temp" alarm, in which case

both "Door Ajar" and "Temp" indicators will activate.

USING YOUR ELECTRONIC CONTROL

Vacation mode (Single and Dual Zone):

This operating mode can be used to save energy during

high cost energy periods, or when you won't be using your

appliance for an extended period of time by disabling the

lights, alarm tones, and keypad entry tones. Vacation mode

also serves as a Sabbath mode, disabling functions and

its controls in accordance with the weekly Sabbath and

religious holidays observed within the Orthodox Jewish

community. When used as Sabbath mode, you may open

or close the door at any time to access contents without

concern of directly turning on or off any lights, digital read-

outs, solenoids, fans, valves, compressor, icons, tones, or

alarms.

When activated, the display, alarm indicators and tones,

keypad touch tones, interior lights, and all options are dis-

abled. All keypad functions are disabled, with the exception

of the "On/Off" keypad which is required to exit Vacation-

mode. Storage compartment temperatures are monitored

and controlled at the settings prior to entering Vacation

mode.

To enter Vacation Mode (with the control out of sleep

mode), press and hold the "On/Off" keypad until the display

goes past "OFF" and reads "VAC". The display will ash

"VAC" 3-times to acknowledge your request, then will

display "VAC" continuously until Vacation mode is exited.

A power outage will not exit Vacation mode, exiting can

only be accomplished manually. To exit Vacation mode and

return to normal operation, press and hold the "On/Off"

keypad until the control displays the temperature.

NOTE

The audible alarm can be muted, for each occurrence, by

pressing the lock keypad.

This alarm condition can be reset by momentarily pressing

the "On/Off" keypad. If this alarm occurs it is recommended

that you check the condition of your stored contents, even

though the appliance is operating normally and the temper-

ature has recovered, as prolonged temperature excursions

could spoil perishables.

NOTE

After a high temperature alarm condition, check all perish-

ables to ensure they are safe for consumption.

The temperature alarm may occur as a result of high usage

or introduction of warm contents to the storage compart-

ment. If the temperature alarm continues to occur, your unit

may require service.

WARNING

CAUTION

OVERLAY DOOR PANEL INSTALLATION

WARNING

Use extreme caution with the articulated hinges. The

hinge is self closing and many pinch points exist prior

to built-in installation. Do not remove the cabinet "Z"

bracket from the top of the cabinet.

Loosen (do not remove ) these

2 phillips head screws on the

top and bottom hinges

If you purchased an overlay panel model, your unit is

equipped with articulated hinges to allow fully integrated

built-in installations. Custom panel thicknesses of

⁄8" (15

mm) and

⁄4" (18 mm) are accommodated.

It is important to use the factory provided grille that came

with the product to assure proper air ow is maintained

through the condenser. The use of a custom grille is not

recommended and will void the warranty.

Figure 11

Figure 11b

Bottom of

door

Figure 11a

"P" clamp

and screw

Wire connector

see Figure 12

Cabinet

"Z" Bracket

Overlay panel models are designed for use with built-

in installations only. Use in freestanding installations

could result in personal injury.

Step 1: Removing the Door

With a phillips screwdriver remove the screw and "P" clamp

from the bottom of the door near the hinge. See Figure 11b.

Disconnect the door wire harness by pressing and holding

down the locking tab on the wire connector and pulling the

connector apart. See Figure 12.

Open the door and loosen the screws holding the hinges to

the cabinet (2 at the top and 2 at the bottom hinge). Do not

remove the screws but loosen them enough so the hinges

can be slipped off of the screws when sliding the door to

the side.

With a helper, and being careful not to scratch the cabinet

or the door, slide the door to the side about

⁄2 inch and

remove the hinges and door from the unit.

The articulated hinges have many pinch points. Care-

fully close / collapse the hinges as soon as the door is

removed from the cabinet.

Figure 13a

OVERLAY DOOR PANEL INSTALLATION

Step 2: Remove the door gasket

With the door laying on a at surface and starting at a

corner of the door remove the magnetic door gasket from

the interior side of the door, see Figure 13. Set the gasket

aside on a at surface.

There are 10 holes in the gasket retainer extrusions, (3 on

each side and 2 at the top and bottom which are used to

fasten the panel to the front of the door. The screws are

provided in the literature pack.

Figure 13

Overlay panel

ush with top

of door.

Holes in

gasket

retainer.

Magnetic Gasket

remove starting at a

corner, grasp and pull

away from the door.

Step 3: Cut and drill the overlay panel

Depending on your model cut the overlay door panel to the

dimensions shown in Figures 14 to 21.

Overlay panel to

be centered on

width of door.

Figure 12

Press and hold down this

tab on the wire connector

and pull the connector apart.

⁄4" (6 mm)

radius is

permissible

⁄32"

(2.9 cm)

⁄32"

(2.9 cm)

Clearance for

screw head,

4 places

Figure 16

Right Hand Hinged

Door 15" (38.1 cm) wide

appliance

OVERLAY DOOR PANEL INSTALLATION

Figure 14

Left Hand Hinged Door

15" (38.1 cm) wide

appliance

Top of door

Clearance for

screw head,

4 places

Hinge side of door

Clearance

for hinge

2 places

⁄4"

(37.5 cm)

⁄4" (6 mm)

Deep

Clearance

for hinge

2 places

Figure 15

Left Hand Hinged Door

15" (38.1 cm) Wide Appliance

⁄32"

(9.7 cm)

⁄16"

(4.3 cm)

⁄4"

(37.5 cm)

⁄4" (6 mm)

Deep

1" (25.4 mm) diameter

counter bore

⁄4" (6.4mm)

deep 4 places.

⁄8"

(10.5 cm)

Minimum

⁄8"

(7.9 cm)

Minimum

Figure 17

Right Hand Hinged Door

15" (38.1 cm) wide appliance

⁄8"

(10.5 cm)

Minimum

⁄2"

(3.8 cm)

typical

(5.1 cm)

⁄16"

(9.4 cm)

⁄32"

(9.7 cm)

⁄2"

(3.8 cm)

typical

1" (25.4 mm) diameter

counter bore

⁄4" (6 mm)

deep 4 places.

(5.1 cm)

⁄16"

(9.4 cm)

⁄8"

(7.9 cm)

Minimum

⁄16"

(4.3 cm)

⁄8"

(12.4 cm)

⁄16"

(3 cm)

⁄8"

(7.9 cm)

(12.7 cm)

⁄4"

(4.4 cm)

⁄8"

(12.4 cm)

(12.7 cm)

⁄8"

(7.9 cm)

Minimum

⁄4"

(4.4 cm)

⁄32"

(77.1 cm)

⁄4" (6 mm)

radius is

permissible

⁄16"

(3 cm)

⁄8"

(7.9 cm)

⁄8"

(7.9 cm)

Minimum

⁄32"

(77.1 cm)

This side

facing interior

This side

facing interior

CAUTION

⁄16"

(3 cm)

⁄32"

(2.9 cm)

Figure 18

Left Hand Hinged Door

24" (61 cm) wide appliance

Weight of overlay door panel

must not exceed 10 pounds

(4.5 kg) for a glass door model.

Figure 20

Right Hand Hinged Door

24" (61 cm) wide appliance

Clearance

for hinge

at top and

bottom

Clearance for

screw head,

4 places

Figure 19

Left Hand Hinged Door

24" (61 cm) wide appliance

Figure 21

Right Hand Hinged Door

24" (61 cm) wide appliance

Clearance for hinge

at top and bottom

Clearance for

screw head,

4 places

Hinge side of door

Top of door

Hinge side of door

OVERLAY DOOR PANEL INSTALLATION

This side

facing interior

This side

facing interior

⁄4"

(60.3 cm)

⁄4"

(6 mm)

Deep

⁄4"

(60.3 cm)

⁄4"

(6 mm)

Deep

1" (2.5 cm) diameter

⁄4" (6 mm) deep

4 places

⁄2"

(3.8 cm)

typical

⁄16"

(4.3 cm)

1" (2.5 cm) diameter

⁄4" (6 mm) deep

4 places

⁄8"

(12.4 cm)

⁄8"

(7.9 cm)

(5.1 cm)

⁄16"

(9.4 cm)

⁄16"

(9.4 cm)

⁄2"

(3.8 cm)

typical

⁄16"

(4.3 cm)

⁄32"

(9.8 cm)

⁄4" (6 mm)

radius is

permissible

14"

(35.6 cm)

⁄16"

(3 cm)

⁄8"

(7.9 cm)

⁄32"

(77.1 cm)

⁄32"

(77.1 cm)

⁄8"

(7.9 cm)

⁄8"

(10.5 cm)

⁄8"

(7.9 cm)

⁄4"

(4.4 cm)

⁄8"

(7.9 cm)

(5.1 cm)

⁄8"

(10.5 cm)

⁄4" (6 mm)

radius is

permissible

14"

(35.6 cm)

⁄8"

(12.4 cm)

⁄32"

(9.8 cm)

⁄8"

(7.9 cm)

⁄4"

(4.4 cm)

⁄32"

(2.9 cm)

Counter bore

lock hole

on back side.

Figure 22a

#10 x

⁄2"

screw

Figure 22

Hinge side of door

⁄2" (13 mm) diameter

drill through door panel,

from other side (see

detail above)

⁄16"

(20.5 mm) counter bore,

⁄16" (11 mm) deep.

⁄32"

(13.7 mm)

⁄2"

(89 mm)

OVERLAY DOOR PANEL INSTALLATION

Step 5: Assemble lock parts

Two (2) lock extensions are provided with the lock. Use the

longer extension for

⁄4" thick overlay panels and the shorter

one for

⁄8" thick overlay panels. Assemble the lock exten-

sion, cam stop washer, spring washer, and set screw to the

lock as shown in Figure 23 and 24.

Install this lock assembly into the lock hole in the overlay

panel and secure with the retaining nut on the back side

with a 15 mm socket and ratchet. Make sure the key slot in

the front of the lock is vertical.

Step 6: Install lock cam

Attach the lock cam to the back of the lock assembly with

the phillips head screw provided. Orient the lock cam verti-

cally when installing on the lock.

Step 4: Assemble the panel to the door

The preferred method of attaching the panel to the door

is to clamp the panel to the door so it cannot move while

drilling the screw pilot holes. Use bar clamps or "C" clamps

with pads on the clamping surfaces that will not mar the

panel or the door. The custom overlay panel should be

ush with the top of the door and centered along the width

of the door. See Figure 13a. Drill holes through the gasket

extrusion using the 10 holes as pilot holes. Use the drill

size from the chart in Table "B", being careful not to drill

through the front surface of the panel. If the overlay panel is

thinner than

⁄8" (16 mm) thick shorter screws will have to be

obtained. Fasten the panel to the door with the 10 screws

provided in the literature pack. (See Figure 22a). Remove

the clamps and replace the gasket in the gasket extrusion

channels of the door. Some force may be required to seat

the gasket into the channels. Be sure the gasket corners

are seated properly.

Material Type #10 Wood Screw

Hardwood

⁄8" (3.2 mm) Diameter. Pilot Hole

Softwood

⁄64 (2.8 mm) Diameter. Pilot Hole

Table B

SECTION A-A

SCALE 1 : 1

LOCK

NUT

BRASS EXTENSION

CAM

PHILLIPS SCREW

13/16 COUNTER

BORE 7/16 DEEP

1/2 HOLE

3/4 INCH

WOOD PANEL

SPRING WASHER

INNER

DOOR

Figure 23

Figure 24

Cam stop

washer

Spring

washer

Cam

Set screw

Lock

Key

Retainer

nut

Screw

Brass extension

(2 lengths provided

Step 8: Secure the cabinet

Use the #8 x

⁄4" black screws from the literature pack to

secure the counter top to the cabinet top through the holes

in the cabinet "Z" bracket.

Step 7: Install the door

Carefully open the top and bottom hinges on the door being

careful as there are many pinch points. Place the hinges

over the 4 screws in the cabinet, 2 at the top and 2 at the

bottom and slide the door into position. Tighten the 4 hinge

screws with a phillips screwdriver. (See Figures 11 and

11a). Place wire harness from the grille and mount to the

bottom of the door with the screw and "P" clamp removed

in step 1. (See Figure 11b). Reconnect the wire harness,

(See Figure 12).

Cabinet

"Z" bracket

#8 x

⁄4" black

screws

(3 places)

Figure 25

OVERLAY DOOR PANEL INSTALLATION

SHELVING CONFIGURATIONS

Shelving Congurations

Your Marvel Professional Series appliance is equipped with

full extension ball bearing shelf glides to provide maximum

access and visibility for the product stored on the shelving

arrangements listed below.

Dual Zone Wine Cellar:

24" (61 cm) Wide models:

Upper Zone: (3) 8 bottle wire racks

Lower Zone: (1) 8 bottle wire rack

(2) 4 bottle half-depth wire racks

Single Zone Wine Cellar:

24" (61 cm) Wide models:

(5) 8 bottle wire racks

(2) 4 bottle half-depth wire racks

Single Zone Wine Cellar:

15" (38.1 cm) Wide models:

(6) 4 bottle wire racks

Figure 26

Figure 28

Figure 27

SHELF REMOVAL AND INSTALLATION

Figure 29

Figure 29a

CAUTION

Never try to remove a loaded shelf, remove everything from

the shelf before removing. Use both hands when removing

the shelf.

To remove a shelf:

Extend the shelf out of the cabinet until it stops.

Unload the shelf (see Figure 29).

Depress the locking tabs on both sides of the shelf and pull

the shelf straight out (see Figure 29a). When the shelf is

removed, push the extended cabinet mounted shelf exten-

sions back into the cabinet.

To re-install a shelf:

Pull out the cabinet mounted shelf extensions to assist the

engagement with the wire rack shelf.

Insert the wire rack side track into the cabinet mounted

shelf extensions on both sides.

Push the wire rack completely into the cabinet to engage

the locking tabs.

Pull the shelf out, (unloaded), to verify the wire rack is

locked into the side rails. If the wire rack falls out, the lock-

ing tabs are not engaged; repeat the installation.

Load the shelf as required.

Locking tab

Remove the

wine from the

shelf to be

removed

The following suggestions will minimize the

cost of operating your refrigeration appliance.

1. Do not install your appliance next to a hot appliance

(cooker, dishwasher, etc.), heating air duct, or other

heat sources.

2. Install product out of direct sunlight.

3. Ensure the front grille vents at front of appliance be-

neath door are not obstructed and kept clean to allow

ventilation for the refrigeration system to expel heat.

4. Plug your appliance into a dedicated power circuit. (Not

shared with other appliances).

5. When initially loading your new product, or whenever

large quantities of warm contents are placed within

refrigerated storage compartment, minimize door

openings for the next 12 hours to allow contents to pull

down to compartment set temperature.

6. Maintaining a relatively full storage compartment will

require less appliance run time than an empty compart-

ment.

7. Ensure door closing is not obstructed by contents

stored in your appliance.

8. Allow hot items to reach room temperature before plac-

ing in product.

9. Minimize door openings and duration of door openings.

10. Use the warmest temperature control set temperature

that meets your personal preference and provides the

proper storage for your stored contents.

11. When on vacation or away from home for extended pe-

riods, set the appliance to warmest acceptable tem-

perature for the stored contents.

12. Set the control to the “off” position if cleaning the

appliance requires the door to be open for an extended

period of time.

13. For wine storage products:

When serving temperatures are not required,

return the compartment(s) set temperature to the

ideal red and white wine long term storage tem-

perature of 13°C / 55°F.

Front Grille

Be sure that nothing obstructs the required air ow open-

ings in front of the cabinet. At least once or twice a year,

brush or vacuum lint and dirt from the front grille area (see

page 4).

SHOCK HAZARD: Disconnect electrical power from the

appliance before cleaning with soap and water.

Cabinet

The painted cabinet can be washed with either a mild soap

and water and thoroughly rinsed with clear water. NEVER

use abrasive scouring cleaners.

Interior

Wash interior compartment with mild soap and water. Do

NOT use an abrasive cleaner, solvent, polish cleaner or

undiluted detergent.

Care of Appliance

1. Avoid leaning on the door, you may bend the door

hinges or tip the appliance.

2. Exercise caution when sweeping, vacuuming or mop-

ping near the front of the appliance. Damage to the

grille can occur.

3. Periodically clean the interior of the appliance as

needed.

4. Periodically check and/or clean the front grille as

needed.

In the Event of a Power Failure

If a power failure occurs, try to correct it as soon as pos-

sible. Minimize the number of door openings while the

power is off so as not to adversely affect the appliance's

temperature.

Light assembly replacement

All models use LED lamps to illuminate the interior of the

appliance. This component is very reliable, but should one

fail, contact a qualied service technician for replacement

of the LED.

CARE AND CLEANING AND ENERGY SAVING TIPS

CAUTION

La page charge ...

Marvel MP24WDG5RS Mode d'emploi

Marque: Marvel

Modèle: MP24WDG5RS

Catégorie: Boissons glacées

Taper: Mode d'emploi

Télécharger le PDF

rapport

dans d''autres langues

English: Marvel MP24WDG5RS User guide

Marvel MP24WDG5RS Mode d'emploi

Marvel MP24WDG5RS Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents