Skil JS820201 Le manuel du propriétaire

WARNING: To reduce the risk of injury, the user must read and understand the

Owner’s Manual before using this product. Save these instructions for future reference.

AVERTISSEMENT : Afin de réduire les risques de blessure, l’utilisateur doit lire et

comprendre le guide d’utilisation avant d’utiliser cet article. Conservez le présent guide

afin de pouvoir le consulter ultérieurement.

ADVERTENCIA : Para reducir el riesgo de lesiones, el usuario debe leer y comprender

el Manual del operador antes de utilizar este producto. Guarde estas instrucciones para

consultarlas en caso sea necesario.

Owner’s Manual

Guide d’utilisation

Manual del propietario

For Customer Service

Pour le service à la clientèle

Servicio al cliente

Model/ Modelo/ Modèle: JS820201

1-877-SKIL-999

OR

www.skil.com

20V Brushless Jig Saw

Scie sauteuse sans balai de 20 V

Sierra de vaivén sin escobillas de 20 V

2

TABLE OF CONTENTS

General Power Tool Safety Warnings . ............................3-5

Safety Warnings for Jig Saw ......................................5

Symbols .....................................................6-9

Get to Know Your Jig Saw .......................................10

Specications .................................................10

Operating Instructions .......................................11-17

Maintenance ...................................................18

Troubleshooting ...............................................19

Limited Warranty of SKIL Cordless Tool ............................20

WARNING

•

Some dust created by power sanding, sawing, grinding, drilling and other construction

activities contains chemicals known to the State of California to cause cancer, birth defects

or other reproductive harm. Some examples of these chemicals are:

–

Lead from lead-based paints.

–

Crystalline silica from bricks, cement, and other masonry products.

–

Arsenic and chromium from chemically-treated lumber.

•

Your risk from these exposures varies, depending upon how often you do this type of work.

To reduce your exposure to these chemicals:

–

Work in a well-ventilated area.

–

Work with approved safety equipment, such as dust masks that are specially designed to

lter out microscopic particles.

–

Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling, and

other construction activities. Wear protective clothing and wash exposed areas with soap

and water. Allowing dust to get into your mouth or eyes or to lie on the skin may promote

absorption of harmful chemicals.

3

GENERAL POWER TOOL SAFETY WARNINGS

WARNING

Read all safety warnings, instructions, illustrations and specications

provided with this power tool.

Failure to follow all instructions listed

below may result in electric shock, re and/or serious injury.

SAVE ALL WARNINGS AND INSTRUCTIONS FOR FUTURE

REFERENCE.

The term "power tool" in the warnings refers to your mains-operated (corded) power tool or

battery-operated (cordless) power tool.

Work area safety

Keep work area clean and well lit.

Cluttered or dark areas invite accidents.

Do not operate power tools in explosive atmospheres, such as in the presence of

ammable liquids, gases or dust.

Power tools create sparks which may ignite the dust or

fumes.

Keep children and bystanders away while operating a power tool.

Distractions can cause

you to lose control.

Electrical safety

Power tool plugs must match the outlet. Never modify the plug in any way. Do not use

any adapter plugs with earthed (grounded) power tools.

Unmodied plugs and matching

outlets will reduce risk of electric shock.

Avoid body contact with earthed or grounded surfaces, such as pipes, radiators,

ranges and refrigerators.

There is an increased risk of electric shock if your body is earthed

or grounded.

Do not expose power tools to rain or wet conditions.

Water entering a power tool will

increase the risk of electric shock.

Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power

tool. Keep cord away from heat, oil, sharp edges or moving parts.

Damaged or entangled

cords increase the risk of electric shock.

When operating a power tool outdoors, use an extension cord suitable for outdoor use.

Use of a cord suitable for outdoor use reduces the risk of electric shock.

If operating a power tool in a damp location is unavoidable, use a ground fault circuit

interrupter (GFCI) protected supply.

Use of a GFCI reduces the risk of electric shock.

Personal safety

Stay alert, watch what you are doing and use common sense when operating a power

tool. Do not use a power tool while you are tired or under the inuence of drugs,

alcohol or medication.

A moment of inattention while operating power tools may result in

serious personal injury.

Use personal protective equipment. Always wear eye protection.

Protective equipment

such as a dust mask, non-skid safety shoes, hard hat or hearing protection used for

appropriate conditions will reduce personal injuries.

Prevent unintentional starting. Ensure the switch is in the off-position before

connecting to power source and/or battery pack, picking up or carrying the tool.

Carrying power tools with your nger on the switch or energising power tools that have the

switch on invites accidents.

Remove any adjusting key or wrench before turning the power tool on.

A wrench or a

key left attached to a rotating part of the power tool may result in personal injury.

4

Do not overreach. Keep proper footing and balance at all times.

This enables better

control of the power tool in unexpected situations.

Dress properly. Do not wear loose clothing or jewellery. Keep your hair and clothing

away from moving parts

. Loose clothes, jewellery or long hair can be caught in moving

parts.

If devices are provided for the connection of dust extraction and collection facilities,

ensure these are connected and properly used.

Use of dust collection can reduce dust-

related hazards.

Do not let familiarity gained from frequent use of tools allow you to become complacent

and ignore tool safety principles.

A careless action can cause severe injury within a fraction

of a second.

Power tool use and care

Do not force the power tool. Use the correct power tool for your application.

The correct

power tool will do the job better and safer at the rate for which it was designed.

Do not use the power tool if the switch does not turn it on and off.

Any power tool that

cannot be controlled with the switch is dangerous and must be repaired.

Disconnect the plug from the power source and/or remove the battery pack, if

detachable, from the power tool before making any adjustments, changing accessories,

or storing power tools.

Such preventive safety measures reduce the risk of starting the

power tool accidentally.

Store idle power tools out of the reach of children and do not allow persons unfamiliar

with the power tool or these instructions to operate the power tool.

Power tools are

dangerous in the hands of untrained users.

Maintain power tools and accessories. Check for misalignment or binding of moving

parts, breakage of parts and any other condition that may affect the power tool’s

operation. If damaged, have the power tool repaired before use.

Many accidents are

caused by poorly maintained power tools.

Keep cutting tools sharp and clean.

Properly maintained cutting tools with sharp cutting

edges are less likely to bind and are easier to control.

Use the power tool, accessories and tool bits etc. in accordance with these instructions,

taking into account the working conditions and the work to be performed.

Use of the

power tool for operations different from those intended could result in a hazardous situation.

Keep handles and grasping surfaces dry, clean and free from oil and grease.

Slippery handles and grasping surfaces do not allow for safe handling and control of the tool

in unexpected situations.

Battery tool use and care

Recharge only with the charger specied by the manufacturer.

A charger that is suitable

for one type of battery pack may create a risk of re when used with another battery pack.

Use power tools only with specically designated battery packs.

Use of any other battery

packs may create a risk of injury and re.

When battery pack is not in use, keep it away from other metal objects, like paper clips,

coins, keys, nails, screws or other small metal objects, that can make a connection

from one terminal to another.

Shorting the battery terminals together may cause burns or a

re.

Under abusive conditions, liquid may be ejected from the battery; avoid contact. If

contact accidentally occurs, ush with water. If liquid contacts eyes, additionally seek

medical help.

Liquid ejected from the battery may cause irritation or burns.

Do not use a battery pack or tool that is damaged or modied.

Damaged or modied

batteries may exhibit unpredictable behaviour resulting in re, explosion or risk of injury.

5

Do not expose a battery pack or tool to re or excessive temperature.

Exposure to re or

temperature above 265 °F may cause explosion.

Follow all charging instructions and do not charge the battery pack or tool outside the

temperature range specied in the instructions.

Charging improperly or at temperatures

outside the specied range may damage the battery and increase the risk of re.

Service

Have your power tool serviced by a qualied repair person using only identical

replacement parts.

This will ensure that the safety of the power tool is maintained.

Never service damaged battery packs.

Service of battery packs should only be performed

by the manufacturer or authorized service providers.

SAFETY WARNINGS FOR JIG SAW

Hold the power tool by insulated gripping surfaces, when performing an operation

where the cutting accessory may contact hidden wiring.

Cutting accessory contacting a

"live" wire may make exposed metal parts of the power tool "live" and could give the operator

an electric shock.

Use clamps or another practical way to secure and support the workpiece to a stable

platform.

Holding the workpiece by hand or against your body leaves it unstable and may

lead to loss of control.

6

SYMBOLS

Safety Symbols

The purpose of safety symbols is to attract your attention to possible dangers. The safety

symbols and the explanations with them deserve your careful attention and understanding.

The symbol warnings do not, by themselves, eliminate any danger. The instructions and

warnings they give are no substitutes for proper accident prevention measures.

WARNING

Be sure to read and understand all safety instructions in this Owner's

Manual, including all safety alert symbols such as “

DANGER

,”

“

WARNING

,” and “

CAUTION

” before using this tool. Failure to following all instructions listed

below may result in electric shock, re, and/or serious personal injury.

The denitions below describe the level of severity for each signal word. Please read the manual

and pay attention to these symbols.

This is the safety alert symbol. It is used to alert you to potential

personal injury hazards. Obey all safety messages that follow this

symbol to avoid possible injury or death.

DANGER

DANGER indicates a hazardous situation which, if not avoided, will

result in death or serious injury.

WARNING

WARNING indicates a hazardous situation which, if not avoided, could

result in death or serious injury.

CAUTION

CAUTION, used with the safety alert symbol, indicates a hazardous

situation which, if not avoided, will result in minor or moderate injury.

Damage Prevention and Information Messages

These inform the user of important information and/or instructions that could lead to equipment

or other property damage if they are not followed. Each message is preceded by the word

“NOTICE”, as in the example below:

NOTICE:

Equipment and/or property damage may result if these instructions are not followed.

WARNING

The operation of any power tools can result in

foreign

objects being thrown into your eyes, which can result

in severe eye damage. Before beginning power tool operation, always

wear safety goggles or safety glasses with side shields and a full face

shield when needed. We recommend a Wide Vision Safety Mask for use

over eyeglasses or standard safety glasses with side shields. Always use

eye protection which is marked to comply with ANSI Z87.1.

7

SYMBOLS (CONTINUED)

IMPORTANT:

Some of the following symbols may be used on your tool. Please study them

and learn their meaning. Proper interpretation of these symbols will allow you to operate the

tool better and more safely.

Symbol Name Designation/Explanation

V Volts Voltage (potential)

A Amperes Current

Hz Hertz Frequency (cycles per second)

W Watt Power

kg Kilograms Weight

min Minutes Time

s Seconds Time

Wh Watt-hours Battery capacity

Ah Ampere-Hours Battery capacity

Ø Diameter Size of drill bits, grinding wheels, etc.

n

0

No load speed Rotational speed, at no load

n Rated speed Maximum attainable speed

…/min

Revolutions or reciprocation

per minute

Revolutions, strokes, surface speed,

orbits, etc. per minute

0 Off position Zero speed, zero torque...

1,2,3,…

I,II,III,

Selector settings

Speed, torque or position settings. Higher

number means greater speed

Innitely variable selector

with off

Speed is increasing from 0 setting

Arrow Action in the direction of arrow

Alternating current Type or a characteristic of current

Direct current Type or a characteristic of current

Alternating or direct current Type or a characteristic of current

Class II construction

Designates Double Insulated Construction

tools.

Earthing terminal Grounding terminal

Li-ion RBRC seal

Designates Li-ion battery recycling

program

8

Symbol Name Designation/Explanation

Ni-Cad RBRC seal

Designates Ni-Cad battery recycling

program

Read manual symbol Alerts user to read manual

Wear eye protection symbol

Always wear safety goggles or safety

glasses with side shields and a full face

shield when operating this product.

9

SYMBOLS (CERTIFICATION INFORMATION)

IMPORTANT:

Some of the following symbols for certication information may be used on your

tool. Please study them and learn their meaning. Proper interpretation of these symbols will

allow you to operate the tool better and more safely.

Symbol Designation/Explanation

This symbol designates that this tool is listed by Underwriters Laboratories.

This symbol designates that this tool is recognized by Underwriters

Laboratories.

This symbol designates that this tool is listed by Underwriters

Laboratories, to United States and Canadian Standards.

This symbol designates that this tool is listed by the Canadian

Standards Association.

This symbol designates that this tool is listed by the Canadian

Standards Association, to United States and Canadian Standards.

This symbol designates that this tool is listed by the Intertek Testing

Services, to United States and Canadian Standards.

This symbol designates that this tool complies to NOM Mexican

Standards.

10

GET TO KNOW YOUR JIG SAW

20V Brushless Jig Saw

Variable-Speed

Trigger Switch

Lock-off Button

LED Light

Tool-less Blade

Change Cover

Foot-

adjustment

Lever

Orbit-Control

Lever

Foot

Blade Roller Guide

Dust-Blowing Switch

Fig. 1

SPECIFICATIONS

Rated voltage 20V d.c.

No-load speed 0~3

,

000 SPM (Strokes per Minute)

Stroke Length 1 in.(25.4mm)

Sawing capacity in wood 4-11/16 in. (120mm),

Sawing capacity in metal 15/32 in. (12mm)

Cutting Angle 0

o

; ±15

o

; ±30

o

; ±45

o

Recommended working temperature 14 ~ 104°F (-10 ~ 40°C)

Recommended storage temperature 32 ~ 104°F (0 ~ 40°C)

11

OPERATING INSTRUCTIONS

WARNING

To reduce the risk of re, personal injury, and product damage due

to a short circuit, never immerse your tool, battery pack, or charger in

uid or allow a uid to ow inside them.

Corrosive or conductive uids, such as seawater,

certain industrial chemicals, and bleach or bleach-containing products, etc. can cause a short

circuit.

WARNING

If any parts are damaged or missing, do not operate this product until

the parts are replaced.

Use of this product with damaged or missing parts

could result in serious personal injury.

WARNING

Do not attempt to modify this tool or create accessories not recom-

mended for use with this tool.

Any such alteration or modication is

misuse and could result in a hazardous condition leading to possibly serious injury.

WARNING

To prevent accidental starting that could cause serious personal

injury, always remove the battery pack from the tool when

assembling parts.

This cordless jig saw must be used only with the battery packs and chargers listed

below:

Battery Pack

Charger

2Ah 2Ah 2

.

5Ah 4Ah 5Ah

SKIL

BY519701

SKIL

BY519702

SKIL

BY519703

SKIL

BY519601

SKIL

BY519603

SKIL

SC535801

SKIL

QC536001

NOTICE:

Please refer to the battery and charger manuals for detailed operating information.

Lock-off Button (Fig. 2)

Your tool is equipped with a lock-off button, located above the variable-speed trigger switch, to

help prevent the saw from being turned on unintentionally.

To lock the saw, depress the lock-off button at the side marked with icon

.

To unlock the saw, depress the lock-off button at the side marked with icon

.

Fig. 2

Lock-off Button

a b

12

To Attach/Detach Battery Pack

Lock the variable-speed trigger switch “OFF”

on the tool by depressing the lock-off button at

the side marked with icon

.

To attach the battery pack:

Align the raised rib on the battery pack with the

grooves in the tool, and then slide the battery

pack onto the tool (Fig. 3).

To detach the battery pack:

Depress the battery-release button, located

on the front of the battery pack, to release the

battery pack. Pull the battery pack out and

remove it from the tool (Fig. 3).

NOTICE:

When placing the battery pack on the

tool, be sure that the raised rib on the battery

pack aligns with the groove on the tool and that the latches snap into place properly. Improper

attachment of the battery pack can cause damage to internal components.

WARNING

Battery tools are always in operating condition. Therefore, the

lock-off button should always be depressed and in the locked

position when not in use or carrying at your side.

Variable-Speed Trigger Switch

Your tool is equipped with a variable-speed

trigger switch. The tool can be turned ON or

OFF by depressing or releasing the trigger.

The variable-speed trigger switch delivers

higher speed with increased trigger pressure

and lower speed with decreased trigger

pressure (Fig. 4).

a. To start the saw, depress the lock-off button

to the unlock position, and then squeeze the

variable-speed trigger switch.

b. To stop the saw, release the variable-speed

trigger switch and depress the lock-off button

to the locked position.

Fig. 4

Variable-speed

Trigger Switch

Fig. 3

Attach

Detach

Battery-release Button

13

Orbital-Action Settings

Your tool is equipped with four orbital-action

settings for optimal adaptation to the cutting

speed, cutting capacity, cutting pattern, and the

material being sawed.

The orbital action can be adjusted with the

control lever:

Setting 0

– No orbital action

Setting 1

– Small orbital action

Setting 2

– Medium orbital action

Setting 3

– Maximum orbital action

The optimal orbital action setting for the

respective application can be determined

through practical testing. The following

recommendations apply:

–

For a ner and cleaner cut, select a lower orbital-action setting or turn it off: setting 0.

–

For thin materials, such as sheet metal, or when sawing splinter-sensitive material, turn the

orbital action off: setting 0.

–

For hard materials

,

such as steel, work with low orbital action: setting 1.

–

For soft materials and when sawing in the direction of the grain, work with maximum orbital

action: setting 3.

NOTICE:

–

Always make test cuts in scrap material rst to determine the best setting.

–

In order to reach full orbital action, the blade must be facing straight forward, the back of

the blade must be resting in the groove of the roller, and the foot must be positioned all

the way forward. Orbital action is not detectable when the saw is running freely. The saw

must be cutting in order for orbital action to occur. The cutting speed is easier to see when

cutting thicker material.

WARNING

To reduce the risk of injury, always allow the jig saw to come to a

complete stop before changing the orbital function setting.

Fig. 5

14

Adjusting the Foot Bevel Angle

(Fig. 6)

Your tool is equipped with quick-reference

detent stops. The foot can be adjusted and

locked to cut angles at 0°, ±15°, ±30° and ±45°.

Depress the lock-off button to the locked

position, and then remove the battery pack

from the tool.

To adjust the foot:

a. Lift the foot-adjustment lever located beneath

the housing.

b. Move the foot slightly forward to disengage

the locking tab.

c. Position the foot to the desired angle

(0°, ±15°, ±30° or ±45°).

d. Push the foot backward to engage the locking tab and retighten the foot-adjustment lever to

maintain the adjustment.

After adjusting the foot, make a sample cut to check the angle.

Dust-Blowing Slide Switch (Fig. 7)

Your tool is equipped with the dust-blowing

function to blow away the dust while cutting for

better visibility.

To blow the sawdust, turn the switch to the

position

.

To turn off the blowing function, turn the switch

to the position

.

Fig. 7

a

b

c

Fig. 6

15

LED Light

Your tool is equipped with an LED light, located

on the front of the tool. This provides additional

light on the surface of the workpiece for

operation in lower-light areas.

The LED light will automatically turn on with a

slight squeeze on the variable-speed trigger

switch before the tool starts running. It will

turn off approximately 10 seconds after the

variable-speed trigger switch is released.

When the tool and/or battery pack become

overloaded or too hot, the internal sensors will

turn the tool off. If the tool and/or battery pack

are overloaded, the LED light will rapidly ash.

Rest the tool for a while or place the tool and

battery pack separately under air ow to cool.

The LED light will ash more slowly to indicate that the battery charge is low. Recharge the

battery pack.

Installing and Removing the Saw

Blade

WARNING

Always turn the tool off

and remove the battery

pack before making any adjustments or

assembling parts.

Depress the lock-off button to the locked

position and then remove the battery pack from

the tool.

To install the saw blade:

a. Lift the tool-less blade change cover up and

insert the blade (with its teeth facing the

cutting direction) into the slot of the tool-less

blade change holder as far as it can go

(Fig. 9).

b. Release the tool-less blade change cover to lock the blade in place.

c. Pull down on the blade to verify that the blade is securely locked in place.

NOTICE:

When inserting the saw blade, the back of the blade must rest in the groove of the

guide roller.

NOTICE:

The tool accepts most commonly available T-shank and U-shank blades.

To remove the saw blade:

a. Lift the tool-less blade change cover up and remove the saw blade.

b. Release the tool-less blade change cover.

WARNING

Use protective gloves when removing the saw blade from the tool, or

rst allow the saw blade to cool down. The saw blade may be hot

after prolonged use.

Fig. 8

Fig. 9

Tool-less Blade

Change Cover

16

Cutting Tips

WARNING

Before attaching the battery pack onto the tool, always check to

determine that the switch performs properly and returns to the “OFF”

position when released.

WARNING

Always wear safety goggles or safety glasses with side shields

during power tool operation or when blowing dust. If operation is

dusty, also wear a dust mask.

WARNING

To avoid loss of control and serious injury, make sure that the blade

reaches the full desired speed before touching it to the workpiece.

Face the good side of the material down and secure it in a bench vise, or clamp it down. Draw

cutting lines or designs on the side of the material facing towards you. Place the front edge

of the saw foot on the workpiece and align the blade with the line to be cut. Hold the jig saw

rmly, turn it on, and press down to keep the saw foot at against the work as you slowly push

the saw into the workpiece in the direction of the cut.

Gradually increase the cutting speed, cutting close to the line (unless you want to leave stock

for nish sanding). You may have to adjust or relocate the vise or clamps as you cut to keep

the work stable. Do not force the saw, or the blade teeth may rub and wear without cutting and

the blade may break. Let the saw do most of the work. When following curves, cut slowly so

that the blade can cut across the grain. This will give you an accurate cut and will prevent the

blade from wandering.

Cutting with a Straightedge

Always use a rough-cut blade when possible.

Clamp a straightedge onto the workpiece

parallel to the line of cut and ush with the side

of the saw foot.

Either a.) rst mark the line of cut and then

position the straightedge parallel and at the

same distance as between the blade and

the side edge of the foot or b.) rst mark the

side edge of the foot and then clamp the

straightedge on the mark and parallel to the cut

line (Fig. 10).

As you cut, keep the saw-foot edge ush

against the straightedge and at on the

workpiece.

Fig. 10

17

Plunge Cutting

Plunge cutting is useful and time-saving in

making rough openings in softer materials. It

is not necessary to drill a hole for an inside or

pocket cut.

a. Draw lines for the opening.

b. Hold the saw rmly and tilt it forward so that

the toe of the saw foot rests on the work, but

with the blade remains well clear of the work.

c. Start the motor, and then very gradually

lower the blade while keeping the toe on

the workpiece. When the blade touches the

work, continue pressing down on the toe of

the saw foot and slowly pivot the saw like a

hinge until the blade cuts through and the

foot rests at on the work.

d. Saw ahead on the line of cut line.

NOTICE:

We do not recommend plunge cutting with a scroll blade.

To make sharp corners, cut up to the corner, then stop the saw and back up slightly before

rounding the corner. After the opening is complete, go back to each corner and cut it from the

opposite direction to square it off.

WARNING

Do not plunge cut into metal surfaces.

Metal Cutting

WARNING

Never use the wood-cutting blade for cutting metals. Failure to do so

could result in serious personal injury.

•

Clamp the material when cutting metal.

•

Be sure to move the saw along slowly.

•

Use lower speeds.

•

Do not twist, bend, or force the blade.

•

If the saw jumps or bounces, use a blade with ner teeth.

•

If the blade seems clogged when cutting soft metal, use a blade with coarser teeth.

•

For easier cutting, lubricate the blade with a stick of cutting wax, if available, or with cutting

oil when cutting steel.

•

Thin metal should be sandwiched between two pieces of wood or tightly clamped onto a

single piece of wood (wood on top of the metal). Draw the cut lines or design on the upper

piece of wood.

•

When cutting aluminum extrusion or angle iron, clamp the work in a bench vise and saw

close to the vise jaws.

•

When sawing tubing and the diameter is larger than the blade is deep, cut through the wall

of the tubing and then insert the blade into the cut, rotating the tube as you saw.

Fig. 11

Toe of Foot

18

MAINTENANCE

WARNING

To avoid serious personal injury, always remove the battery pack

from the tool when cleaning or performing any maintenance.

Service

WARNING

Preventive maintenance performed by unauthorized personnel may

result in misplacing internal wires and components, which could

cause serious hazard.

We recommend that all tool service be performed by a SKIL Service

Center or Authorized SKIL Service Station.

General Maintenance

WARNING

When servicing, use only identical replacement parts. Use of any

other parts could create a hazard or cause product damage.

Periodically inspect the entire product for damaged, missing, or loose parts such as screws,

nuts, bolts, caps, etc. Securely tighten all fasteners and caps and do not operate this product

until all missing or damaged parts are replaced. Please contact customer service or an

authorized service center for assistance.

Retighten the Foot (Fig. 12)

If the foot-adjustment lever loosens during use,

set its tightness following the procedure below:

a. Place the foot-adjustment lever in the middle

position.

b. Loosen the locking screw counterclockwise

with a PH2 screwdriver.

c. Tighten the set screw nger tight

clockwise with a 4mm Allen key.

d. Tighten the locking screw clockwise with a

PH2 screwdriver.

e. Tighten the foot-adjustment lever.

Cleaning

WARNING

The tool may be cleaned most effectively with compressed dry air.

Always

wear safety goggles when cleaning tools with compressed air.

Ventilation openings and switch selectors must be kept clean and free of foreign matter. Do

not attempt to clean by inserting pointed objects through openings.

WARNING

Certain cleaning agents and solvents damage plastic parts.

Some of

these are: gasoline, carbon tetrachloride, chlorinated cleaning solvents,

ammonia and household detergents that contain ammonia.

Storage

Store the tool indoors in a place that is inaccessible to children. Keep away from corrosive

agents.

Fig. 12

Set Screw

Locking

Screw

19

TROUBLESHOOTING

Problem Cause Remedy

Tool will not start. 1. Battery pack is depleted.

2. Battery pack is not installed

properly.

3. Burned out switch.

1. Charge the battery.

2. Conrm battery is locked in place

and secured to the tool.

3. Have the switch replaced by an

Authorized SKIL Service Center or

Service Station.

The blade binds,

jams, or bums the

wood.

1. The blade is dull.

2. An improper blade is being

used.

3. The blade is warped.

1. Replace the blade.

2. Choose the right blade for your

operation.

3. Replace the blade.

The saw vibrates or

shakes.

1. The blade is damaged.

2. The blade is loose.

1. Replace the blade.

2. Remove the blade and reinstall it.

20

LIMITED WARRANTY OF SKIL CONSUMER TOOLS

5 YEAR LIMITED WARRANTY- LEGAL

Chervon North America, Inc. ("Seller") warrants to the original purchaser only, that all SKIL

consumer TOOLS will be free from defects in material or workmanship for a period of ve

years from date of purchase, if original purchaser registers the product within 30 days from

purchase. BATTERIES AND CHARGERS are warranted for 2 years. Product registration

can be completed online at www.Registermyskil.com. Original purchasers should also retain

their receipt as proof of purchase. THE FIVE-YEAR WARRANTY PERIOD FOR TOOLS IS

CONDITIONED ON REGISTRATION OF THE PRODUCT WITHIN 30 DAYS OF PURCHASE.

If original purchasers do not register their product timely, the foregoing limited warranty will

apply for a duration of three years for tools. All batteries and chargers will remain under the

two-year limited warranty.

Notwithstanding the foregoing, if a SKIL consumer tool is used for industrial, professional

or commercial purposes, the foregoing warranty will apply for a duration of ninety days,

regardless of registration.

SELLER’S SOLE OBLIGATION AND YOUR EXCLUSIVE REMEDY under this Limited

Warranty and, to the extent permitted by law, any warranty or condition implied by law, shall

be the repair or replacement of parts, without charge, which are defective in material or

workmanship and which have not been misused, carelessly handled, or repaired by persons

other than Seller or Authorized Service Station. To make a claim under this Limited Warranty,

you must return the complete product, transportation prepaid, to any SKIL Factory Service

Center or Authorized Service Station. For Authorized SKIL Power Tool Service Stations,

please visit www.Registermyskil.com or call 1-877-SKIL-999 (1-877-754-5999).

THIS LIMITED WARRANTY DOES NOT APPLY TO ACCESSORY ITEMS SUCH AS

CIRCULAR SAW BLADES, DRILL BITS, ROUTER BITS, JIGSAW BLADES, SANDING

BELTS, GRINDING WHEELS AND OTHER RELATED ITEMS.

ANY IMPLIED WARRANTIES APPLICABLE TO A PRODUCT SHALL BE LIMITED IN

DURATION EQUAL TO THE DURATION OF THE EXPRESS WARRANTIES APPLICABLE

TO SUCH PRODUCT, AS SET FORTH IN THE FIRST PARAGRAPH ABOVE. SOME

STATES IN THE U.S., SOME CANADIAN PROVINCES DO NOT ALLOW LIMITATIONS ON

HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION MAY NOT

APPLY TO YOU.

IN NO EVENT SHALL SELLER BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL

DAMAGES (INCLUDING BUT NOT LIMITED TO LIABILITY FOR LOSS OF PROFITS)

ARISING FROM THE SALE OR USE OF THIS PRODUCT. SOME STATES IN THE U.S.

AND SOME CANADIAN PROVINCES DO NOT ALLOW THE EXCLUSION OR LIMITATION

OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR

EXCLUSION MAY NOT APPLY TO YOU.

THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO

HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE IN THE U.S., PROVINCE

TO PROVINCE IN CANADA AND FROM COUNTRY TO COUNTRY.

THIS LIMITED WARRANTY APPLIES ONLY TO PRODUCTS SOLD WITHIN THE UNITED

STATES OF AMERICA, CANADA AND THE COMMONWEALTH OF PUERTO RICO. FOR

WARRANTY COVERAGE WITHIN OTHER COUNTRIES, CONTACT YOUR LOCAL SKIL

DEALER OR IMPORTER.

12/18

La page charge ...

Skil JS820201 Le manuel du propriétaire

Ce manuel convient également à

Skil JS820201 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents