Sanyo SPW-UMR124EXH56 Manuel utilisateur

Marque: Sanyo

Modèle: SPW-UMR124EXH56

Catégorie: Climatiseurs split-system

Taper: Manuel utilisateur

– ECO-i System Air Conditioner –

INSTALLATION AND OPERATION MANUAL

■ R410A Models

Indoor Units

Outdoor Units

SPW-UMR74EXH56

SPW-UMR94EXH56

SPW-UMR124EXH56

SPW-UMR164EXH56

SPW-UMR184EXH56

SPW-UMR224EXH56

* Refrigerant R410A is used in the outdoor units.

DC Inverter Main Unit SPW-CR604GDXH8, SPW-CR704GDXH8, SPW-CR904GDXH8, SPW-CR1154GDXH8

Constant Speed (Sub) Unit SPW-CR704GDCH8, SPW-CR904GDCH8, SPW-CR1154GDCH8

Optional Controllers

Remote Controller RCS-SH80AG

RC Wireless Remote Controller RCS-BH80AG.WL

Simplified Remote Controller RCS-KR1AG

for Refrigerant R410A

SANYO Airconditioners Europe S.r.l.

Via Bisceglie, No. 76

20152 Milano, Italy

37.4196.054.0 ©SANYO 2005

IMPORTANT!

Please Read Before Starting

This air conditioning system meets strict safety and operat-

ing standards. As the installer or service person, it is an

important part of your job to install or service the system so it

operates safely and efficiently.

For safe installation and trouble-free operation, you must:

●

Carefully read this instruction booklet before beginning.

●

Follow each installation or repair step exactly as shown.

●

Observe all local, state, and national electrical codes.

●

This product is intended for professional use.

Permission from the power supplier is required when

installing an outdoor unit that is connected to a 16 A

distribution network.

●

Pay close attention to all warning and caution notices

given in this manual.

This symbol refers to a hazard or

unsafe practice which can result

in severe personal injury or death.

This symbol refers to a hazard or

unsafe practice which can result

in personal injury or product or

property damage.

If Necessary, Get Help

These instructions are all you need for most installation

sites and maintenance conditions. If you require help for a

special problem, contact our sales/service outlet or your

certified dealer for additional instructions.

In Case of Improper Installation

The manufacturer shall in no way be responsible for

improper installation or maintenance service, including fail-

ure to follow the instructions in this document.

SPECIAL PRECAUTIONS

When Wiring

ELECTRICAL SHOCK CAN CAUSE

SEVERE PERSONAL INJURY OR DEATH.

ONLY A QUALIFIED, EXPERIENCED

ELECTRICIAN SHOULD ATTEMPT TO

WIRE THIS SYSTEM.

• Do not supply power to the unit until all wiring and tubing

are completed or reconnected and checked.

• Highly dangerous electrical voltages are used in this sys-

tem. Carefully refer to the wiring diagram and these

instructions when wiring. Improper connections and inad-

equate grounding can cause accidental injury or death.

• Ground the unit following local electrical codes.

• Connect all wiring tightly. Loose wiring may cause over-

heating at connection points and a possible fire hazard.

When Transporting

Be careful when picking up and moving the indoor and outdoor

units. Get a partner to help, and bend your knees when lifting

to reduce strain on your back. Sharp edges or thin aluminum

fins on the air conditioner can cut your fingers.

When Installing…

…In a Room

Properly insulate any tubing run inside a room to prevent

“sweating” that can cause dripping and water damage to

walls and floors.

…In Moist or Uneven Locations

Use a raised concrete pad or concrete blocks to provide a

solid, level foundation for the outdoor unit. This prevents

water damage and abnormal vibration.

…In an area with High Winds

Securely anchor the outdoor unit down with bolts and a

metal frame. Provide a suitable air baffle.

…In a Snowy Area (for Heat Pump-type Systems)

Install the outdoor unit on a raised platform that is higher

than drifting snow. Provide snow vents.

When Connecting Refrigerant Tubing

• Ventilate the room well, in the event that is refrigerant

gas leaks during the installation. Be careful not to allow

contact of the refrigerant gas with a flame as this will

cause the generation of poisonous gas.

• Keep all tubing runs as short as possible.

• Use the flare method for connecting tubing.

• Apply refrigerant lubricant to the matching surfaces of

the flare and union tubes before connecting them, then

tighten the nut with a torque wrench for a leak-free con-

nection.

• Check carefully for leaks before starting the test run.

Depending on the system type, liquid and gas lines may

be either narrow or wide. Therefore, to avoid confusion

the refrigerant tubing for your particular model is speci-

fied as either “narrow” or “wide” than as “liquid” or “gas.”

When Servicing

• Turn the power OFF at the main power box (mains)

before opening the unit to check or repair electrical parts

and wiring.

• Keep your fingers and clothing away from any moving

parts.

• Clean up the site after you finish, remembering to check

that no metal scraps or bits of wiring have been left

inside the unit being serviced.

• Ventilate any enclosed areas when installing or testing the

refrigeration system. Escaped refrigerant gas, on contact

with fire or heat, can produce dangerously toxic gas.

• Confirm after installation that no refrigerant gas is leak-

ing. If the gas comes in contact with a burning stove, gas

water heater, electric room heater or other heat source, it

can cause the generation of poisonous gas.

NOTE

WARNING

CAUTION

2. The standards for minimum room volume are as

follows.

(1) No partition (shaded portion)

(2) When there is an effective opening with the adja-

cent room for ventilation of leaking refrigerant gas

(opening without a door, or an opening 0.15% or

larger than the respective floor spaces at the top

or bottom of the door).

(3) If an indoor unit is installed in each partitioned

room and the refrigerant tubing is interconnected,

the smallest room of course becomes the object.

But when mechanical ventilation is installed inter-

locked with a gas leakage detector in the smallest

room where the density limit is exceeded, the vol-

ume of the next smallest room becomes the object.

3. The minimum indoor floor space compared with the

amount of refrigerant is roughly as follows: (When

the ceiling is 2.7 m high)

Check of Density Limit

The room in which the air conditioner is to be

installed requires a design that in the event of

refrigerant gas leaking out, its density will not

exceed a set limit.

The refrigerant (R410A), which is used in the air condi-

tioner, is safe, without the toxicity or combustibility of

ammonia, and is not restricted by laws imposed to pro-

tect the ozone layer. However, since it contains more

than air, it poses the risk of suffocation if its density

should rise excessively. Suffocation from leakage of

refrigerant is almost non-existent. With the recent

increase in the number of high density buildings, how-

ever, the installation of multi air conditioner systems is

on the increase because of the need for effective use

of floor space, individual control, energy conservation

by curtailing heat and carrying power, etc.

Most importantly, the multi air conditioner system is

able to replenish a large amount of refrigerant com-

pared to conventional individual air conditioners. If a

single unit of the multi air conditioner system is to be

installed in a small room, select a suitable model and

installation procedure so that if the refrigerant acci-

dentally leaks out, its density does not reach the limit

(and in the event of an emergency, measures can be

made before injury can occur).

In a room where the density may exceed the limit,

create an opening with adjacent rooms, or install

mechanical ventilation combined with a gas leak

detection device. The density is as given below.

Total amount of refrigerant (kg)

Min. volume of the indoor unit installed room (m

)

≤ Density limit (kg/m

)

The density limit of refrigerant which is used in multi air con-

ditioners is 0.3 kg/m

(ISO 5149).

1. If there are 2 or more refrigerating systems in a sin-

gle refrigerating device, the amount of refrigerant

should be as charged in each independent device.

For the amount of charge in this example:

The possible amount of leaked refrigerant gas in rooms

A, B and C is 10 kg.

The possible amount of leaked refrigerant gas in rooms

D, E and F is 15 kg.

NOTE

Outdoor unit

Refrigerant tubing

Indoor unit

e.g., charged

amount (10 kg)

Outdoor unit

Indoor unit

Room A Room B Room C Room D Room E Room F

e.g., charged

amount (15 kg)

Refrigerant tubing

Outdoor unit

Very

small

room

Indoor unit

Small

room

Medium

room

Large room

Mechanical ventilation device – Gas leak detector

10 20 30

Total amount of refrigerant

Min. indoor floor space

Range below the

density limit

of 0.3 kg/m

(countermeasures

not needed)

Range above

the density limit

of 0.3 kg/m

(countermeasures

needed)

1. GENERAL

This booklet briefly outlines where and how to install the air conditioning system. Please read over the entire set of

instructions for the indoor unit and make sure all accessory parts listed are with the system before beginning.

1-2. Type of Copper Tube and Insulation Material

If you wish to purchase these materials separately

from a local source, you will need:

1. Deoxidized annealed copper tube for refrigerant

tubing.

2. Foamed polyethylene insulation for copper tubes as

required to precise length of tubing. Wall thickness

of the insulation should be not less than 8 mm.

3. Use insulated copper wire for field wiring. Wire

size varies with the total length of wiring. Refer to

4. Electrical Wiring for details.

1-3. Additional Materials Required for Installation

1. Refrigeration (armored) tape

2. Insulated staples or clamps for connecting wire

(See your local codes.)

3. Putty

4. Refrigeration tubing lubricant

5. Clamps or saddles to secure refrigerant tubing

6. Scale for weighing

CAUTION

Check local electrical codes

and regulations before

obtaining wire. Also, check

any specified instructions

or limitations.

IMPORTANT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Please Read Before Starting

Check of Density Limit

1. GENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

1-1. Tools Required for Installation (not supplied)

1-2. Type of Copper Tube and Insulation Material

1-3. Additional Materials Required for Installation

2. HOW TO INSTALL THE UNIT . . . . . . . . . . . . . .5

2-1. Duct for fresh air

3. TEST OF THE SYSTEM AND CONTROL OF THE

AIR VOLUME TO THE OUTLET GRILLES . . . .7

CONTENTS

Page

1-1. Tools Required for Installation (not supplied)

1. Standard screwdriver

2. Phillips head screwdriver

3. Knife or wire stripper

4. Tape measure

5. Carpenter’s level

6. Sabre saw or key hole saw

7. Hacksaw

8. Core bits

9. Hammer

10. Drill

11. Tube cutter

12. Tube flaring tool

13. Torque wrench

14. Adjustable wrench

15. Reamer (for deburring)

4. ELECTRICAL WIRING . . . . . . . . . . . . . . . . . . . .8

4-1. General Precautions on Wiring

4-2. Recommended Wire Length and Wire Diame-

ter for Power Supply System

4-3. Wiring System Diagrams

5. HOW TO PROCESS TUBING . . . . . . . . . . . . . .12

5-1. Connecting the Refrigerant Tubing

5-2. Connecting Tubing between Indoor and Out-

door Units

5-3. Insulating the Refrigerant Tubing

5-4. Taping the Tubes

5-5. Finishing the Installation

6 APPENDIX . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

2. HOW TO INSTALL THE UNIT

Fig. 2-1

Minimum operation and maintenance area. (fig. 2-1)

Fig. 2-2

Fig. 2-4

Find the space for the installation of the return air grille and

mark the opening to do. Cut the falseceiling. (fig. 2-2)

Use rawl plug suitable to the ceiling consistence and four

M10 threaded bars of suitable length (not supplied). (fig. 2-

Mark on the ceiling the holes for the hanging rods, verify the

distance of the centres. The value included in the brackets

is referred to the model X18. (fig. 2-4)

Drill a 80 mm diameter hole, for the passage of refrigeration

pipework, condensate pipework and electrical cable. Insert

a PVC pipe in the wall. (fig. 2-5)

Secure the unit in position with locknuts and washers, level

the unit, keeping the right distance from the falseceiling for

the installation of return air grille. (fig. 2-6)

Foresee a removable panel of the falseceiling for servicing.

(fig. 2-7)

The unit is supplied with PVC hose from the condensate

pump. Maximum pump lift is 250 mm over the unit. Convoy

the condensate with a positive slope (min. 1:100) to the out-

side. The highest point in the condensate pipework should

be as close to the unit as possible. This prevents a large

volume of water draining back into the unit when it is

switched off. (fig. 2-8)

Convoy the condensate to the outside with a positive slope,

from a trap at the end if necessary. (fig. 2-9)

300

Fig. 2-3

Fig. 2-5

Fig. 2-6

Fig. 2-7

Fig. 2-8

Fig. 2-9

7/9/12 1500 1100

16/18/22 1700 1100

Intake coduct

False ceiling

Air intake

Outlet conduct

On the front and rear side of the unit a rectangular port

(with flange) helps during duct mounting. (fig. 2-10)

Rear and front flange for the air intake. The value included

in the brackets is referred to the model X18. (fig. 2-11)

Discarge air duct (optional accessory).

Contact the After Sale Service. (fig. 2-12)

Remove the filter and pour, inside the condensate drain

pan, 0.5 liter of water. Start the unit checking for proper

drain pump operation. (fig. 2-13)

Fig. 2-10

Fig. 2-11

Fig. 2-12

Fig. 2-13

There is a duct connection port  for drawing in fresh air.

The supplementary fan motor for outside air intake has to be supplied separately and controlled by a bipolar ON-OFF switch

with safety fuses.

Fresh air flow must be about 10% of the total air flow to avoid operating problems and noise.

•

Open the knock-out hole  , fix a  120 mm flange on the unit and connect the thermically insulated duct.

•

Install an outside grille with filter inspection port to prevent dust and leaves from entering and fouling the indoor unit heat

exchanger.

2-1 Duct for fresh air

3. TEST OF THE SYSTEM AND CONTROL OF THE AIR VOLUME TO THE OUTLET GRILLES

The unit is prearranged to supply an external static pressure

of about 5 mm. Too high resistances in the air distribution

system can cause an exceedingly small air volume to the

outlet grilles.

This trouble can be solved by increasing the fan speed as

follows:

Open the cover of the electrical junction box. Take out the

booster cable clamped in the box. (fig. 3-1)

Disconnect the fan motor plug in the electrical box and insert

the booster cable as a cable extension between the motor

plug and the socket from the PCB. The external static pres-

sure will increase to 7 mm w.g. Check static pressure and air

flow rate on the fan performance graph. (fig. 3-2)

Fan motor

Booster cable

Connector motor cable (at the supply)

Fig. 3-1

Fig. 3-2

200 400 600 800 1000

300 500 700 900 1100 1300 1500

7/9/12

16/18/22

EXTERNAL STATIC PRESSURE (mmW.G.)

H = High fan speed

L = Low fan speed

HH = Very high fan speed

M = Middle fan speed

H: Standard supplied unit. Available fan speeds: Low-Midd-

le-High (L - M - H). Max. static pressure: about 5 mm

HH: Unit with cable extension of the fan motor (booster

cable). Available fan speeds: Middle-High-Very high (M -

H - HH). Max. static pressure: about 7 mm



Control wiring

indoor units) control wiring

(D) Remote control wiring (E) Control wiring for group control

(F) Inter-outdoor unit control wiring

0.75 mm

(AWG #18)

0.75 mm

(AWG #18)

0.75 mm

(AWG #18)

Use shielded wiring* Use shielded wiring Use shielded wiring

0.75 mm

(AWG #18)

Use shielded wiring

Max. 1,000 m

Max. 500 m

Max. 500 m (Total)

Max. 500 m

4. ELECTRICAL WIRING

4-1. General Precautions on Wiring

(1) Before wiring, confirm the rated voltage of the unit

as shown on its nameplate, then carry out the

wiring closely following the wiring diagram.

(2) Provide a power outlet to be used exclusively for

each unit, and a power supply disconnect and cir-

cuit breaker for overcurrent protection should be

provided in the exclusive line.

(3) To prevent possible hazards from insulation fail-

ure, the unit must be grounded.

(4) Each wiring connection must be done in accor-

dance with the wiring system diagram. Wrong

wiring may cause the unit to misoperate or

become damaged.

(5) Do not allow wiring to touch the refrigerant tubing,

compressor, or any moving parts of the fan.

(6) Unauthorized changes in the internal wiring can be

very dangerous. The manufacturer will accept no

responsibility for any damage or misoperation that

occurs as a result of such unauthorized changes.

(7) Regulations on wire diameters differ from locality

to locality. For field wiring rules, please refer to

your LOCAL ELECTRICAL CODES before begin-

ning.

You must ensure that installation complies with all

relevant rules and regulations.

(8) To prevent malfunction of the air conditioner

caused by electrical noise, care must be taken

when wiring as follows:

● The remote control wiring and the inter-unit control

wiring should be wired apart from the inter-unit

power wiring.

● Use shielded wires for inter-unit control wiring

between units and ground the shield on both sides.

(9) If the power supply cord of this appliance is dam-

aged, it must be replaced by a repair shop

appointed by the manufacture, because special

purpose tools are required.

4-2. Recommended Wire Length and Wire Diameter for Power Supply System

Outdoor unit

(A) Power supply

Wire size Max. length

SPW-CR604GDXH8 113 m 15 A

SPW-CR704GDXH8 74 m 30 A

SPW-CR904GDXH8 60 m 35 A

SPW-CR1154GDXH8 55 m 40 A

SPW-CR704GDCH8 47 m 35 A

SPW-CR904GDCH8 46 m 40 A

SPW-CR1154GDCH8

4 mm

6 mm

2.5 mm

6 mm

10 mm

6 mm

10 mm

39 m 50 A

Time delay fuse or

circuit capacity

Time delay fuse or

circuit capacity

70 m

74 m

60 m

91 m

47 m

77 m

65 m

16A

35A

50A

35A

50A

Indoor unit

Time delay fuse or

circuit capacity

(B) Power supply

2.5 mm

Max. 130 m

10 ~ 16A

NOTE

* With ring-type wire terminal.

4-3. Wiring System Diagrams

WHT

Remote

controller

BLK

WHT

Remote

controller

Group control:

BLK

WHT

Remote

controller

Indoor

unit (No. n)

Indoor

unit (No. 1)

Indoor

unit (No. 2)

Indoor

unit (No. 3)

Outdoor unit

INV unit

Power supply

380-415V-3N 50Hz

Ground

BLK

Outdoor unit

CS unit

Power supply

220-240V 50Hz

Ground

Power supply

Ground

380-415V-3N 50Hz

Power supply

220-240V 50Hz

Power supply

220-240V 50Hz

Power supply

220-240V 50Hz

Ground

Inter-outdoor-unit control wiring

NOTE

(1) Refer to Section 5-2. “Recommended Wire Length

and Wire Diameter for Power Supply System” for

the explanation of “A,” “B,” “C,” “D,” and “E,” in the

above diagrams.

(2) The basic connection diagram of the indoor unit

shows the 7P terminal board, so the terminal

boards in your equipment may differ from the dia-

gram.

(3) Refrigerant Circuit (R.C.) address should be set

before turning the power on.

7P terminal board

1(L)

power

supply

2(N) U1 U2

Inter-unit

control

wiring

R1 R2

Remote

controller

Outdoor unit Outdoor unit Outdoor unit

Indoor unit Indoor unit Indoor unit Indoor unit

Indoor unit

more than 1 m

Branch

point

16 or fewer

Indoor unit

Indoor unit Indoor unit Indoor unit

less than 1 m

Indoor unit

Outdoor unit Indoor unit Indoor unit Indoor unit

Indoor unit Indoor unit Indoor unit

Outdoor unit

Indoor unit

Branch point

(1) When linking outdoor units in a network (S-net link system), disconnect the terminal extended from the

short plug (CN003, 2P Black, location: right bottom on the outdoor main control PCB) from all outdoor

units except any one of the outdoor units.

(When shipping: In shorted condition.)

Otherwise the communication of S-net link system is not performed. For a system without link (no con-

nection wiring between outdoor units), do not remove the short plug.

(2) Do not install the inter-unit control wiring in a way that forms a loop. (Fig. 4-1)

Outdoor unit Outdoor unit Outdoor unit

Prohibited

Indoor unit Indoor unit Indoor unit Indoor unit Indoor unit

Fig. 4-1

Fig. 4-2

Fig. 4-3

CAUTION

(3) Do not install inter-unit control wiring such as star

branch wiring. Star branch wiring causes mis-address

setting.

(4) If branching the inter-unit control wiring, the number of branch points should be 16 or fewer.

(Branches less than 1 m are not included in the total branch number.) (Fig. 4-3)

Fig. 4-4

Shielded wire

Ground

Fig. 4-5

Stranded wire

Ring

pressure

terminal

Strip 10 mm

Fig. 4-6

Wire

Special

washer

Screw

Ring pressure

terminal

Terminal plate

Screw and

Special washer

Ring

pressure

terminal

Wire

(5) Use shielded wires for inter-unit control wiring

wise misoperation from noise may occur.

(Fig. 4-4)

Connect wiring as shown in Section “4-3.

Wiring System Diagrams.”

WARNING

Loose wiring may cause

the terminal to overheat or

result in unit malfunction.

A fire hazard may also

exist. Therefore, ensure

that all wiring is tightly

connected.

When connecting each power wire to the terminal, fol-

low the instructions on “How to connect wiring to the

terminal” and fasten the wire securely with the fixing

screw of the terminal plate.

How to connect wiring to the terminal

■ For stranded wiring

(1) Cut the wire end with cutting pliers, then strip the

insulation to expose the stranded wiring about 10

mm and tightly twist the wire ends. (Fig. 4-5)

(2) Using a Phillips head screwdriver, remove the ter-

minal screw(s) on the terminal plate.

(3) Using a ring connector fastener or pliers, securely

clamp each stripped wire end with a ring pressure

terminal.

(4) Place the ring pressure terminal, and replace and

tighten the removed terminal screw using a screw-

driver. (Fig. 4-6)

5. HOW TO PROCESS TUBING

The narrow tubing side is connected by a flare nut,

and the wide tubing side is connected by brazing.

5-1. Connecting the Refrigerant Tubing

Use of the Flaring Method

Many of conventional split system air conditioners

employ the flaring method to connect refrigerant tubes

which run between indoor and outdoor units. In this

method, the copper tubes are flared at each end and

connected with flare nuts.

Flaring Procedure with a Flare Tool

(1) Cut the copper tube to the required length with a

tube cutter. It is recommended to cut approx. 30

– 50 cm longer than the tubing length you esti-

mate.

(2) Remove burrs at the end of the copper tube with a

tube reamer or file. This process is important and

should be done carefully to make a good flare.

(Fig. 5-1)

When reaming, hold the tube end downward and be

sure that no copper scraps fall into the tube. (Fig. 5-2)

(3) Remove the flare nut from the unit and be sure to

mount it on the copper tube.

(4) Make a flare at the end of copper tube with a

flare tool.* (Fig. 5-3)

(*Use “RIGID

” or equivalent.)

A good flare should have the following characteristics:

● inside surface is glossy and smooth

● edge is smooth

● tapered sides are of uniform length

NOTE

Deburring

Before

After

Fig. 5-1

Reamer

Copper

tubing

Fig. 5-2

Flare tool

Flare nut

Copper

tubing

Fig. 5-3

Caution Before Connecting Tubes Tightly

(1) Apply a sealing cap or water-proof tape to prevent

dust or water from entering the tubes before they

are used.

(2) Be sure to apply refrigerant lubricant to the match-

ing surfaces of the flare and union before connect-

ing them together. This is effective for reducing

gas leaks. (Fig. 5-4)

(3) For proper connection, align the union tube and

flare tube straight with each other, then screw in

the flare nut lightly at first to obtain a smooth

match. (Fig. 5-5)

● Adjust the shape of the narrow tube (liquid tube)

using a tube bender at the installation site and

connect it to the narrow tubing side (liquid tubing

side) valve using a flare.

Cautions During Brazing

● Replace air inside the tube with nitrogen gas to

prevent copper oxide film from forming during

the brazing process. (Oxygen, carbon dioxide

and Freon are not acceptable.)

● Do not allow the tubing to get too hot during

brazing. The nitrogen gas inside the tubing

may overheat, causing refrigerant system

valves to become damaged. Therefore allow

the tubing to cool when brazing.

● Use a reducing valve for the nitrogen cylinder.

● Do not use agents intended to prevent the for-

mation of oxide film. These agents adversely

affect the refrigerant and refrigerant oil, and

may cause damage or malfunctions.

5-2. Connecting Tubing Between Indoor and Out-

door Units

(1) Tightly connect the indoor-side refrigerant tubing

extended from the wall with the outdoor-side tub-

ing.

(2) To fasten the flare nuts, apply specified torque as

at right:

● When removing the flare nuts from the tubing con-

nections, or when tightening them after connecting

the tubing, be sure to use 2 monkey wrenches or

spanners as shown. (Fig. 5-6)

If the flare nuts are over-tightened, the flare may be

damaged, which could result refrigerant leakage

and cause in injury or asphyxiation to room occu-

pants.

● For the flare nuts at tubing connections, be sure to

use the flare nuts that were supplied with the unit,

or else flare nuts for R410A (type 2). The refriger-

ant tubing that is used must be of the correct wall

thickness as shown in the table at right.

Apply refrigerant

lubricant here and here

Fig. 5-4

Flare nut

Union

Fig. 5-5

Fig. 5-6

Indoor unit

Outdoor unit

Spanner

Torque wrench

Tube diameter

6.35 (1/4")

9.52 (3/8")

12.7 (1/2")

15.88 (5/8")

Tightening torque,

approximate

14 – 18 N

(140 – 180 kgf

cm)

34 – 42 N

(340 – 420 kgf

cm)

49 – 61 N

(490 – 610 kgf

cm)

68 – 82 N

(680 – 820 kgf

cm)

0.8 mm

1.0 mm

Tube thickness

Because the pressure is approximately 1.6 times

higher than conventional refrigerant pressure, the

use of ordinary flare nuts (type 1) or thin-walled

tubes may result in tube rupture, injury, or asphyxi-

ation caused by refrigerant leakage.

● In order to prevent damage to the flare caused by

over-tightening of the flare nuts, use the table

above as a guide when tightening.

● When tightening the flare nut on the narrow tube,

use a monkey wrench with a nominal handle length

of 200 mm.

Fig. 5-8

Fig. 5-7

Fig. 5-9

5-3. Insulating the Refrigerant Tubing

Tubing Insulation

● Thermal insulation must be applied to all unit tub-

ing, including distribution joint (purchased sepa-

rately).

* For gas tubing, the insulation material must be

heat resistant to 120°C or above. For other tubing,

it must be heat resistant to 80°C or above.

Insulation material thickness must be 10 mm or

greater.

If the conditions inside the ceiling exceed DB 30°C

and RH 70%, increase the thickness of the gas

tubing insulation material by 1 step.

Taping the flare nuts

Wind the white insulation tape around the flare nuts at

the wide tube connections. Then cover up the tubing

connections with the flare insulator, and fill the gap at

the union with the supplied black insulation tape.

Finally, fasten the insulator at both ends with the sup-

plied vinyl clamps. (Fig. 5-8)

Insulation material

The material used for insulation must have good insu-

lation characteristics, be easy to use, be age resis-

tant, and must not easily absorb moisture.

After a tube has been insu-

lated, never try to bend it

into a narrow curve

because it can cause the

tube to break or crack.

CAUTION

Never grasp the drain or refrigerant connecting

outlets when moving the unit.

Unit side

insulator

Insulation tape (white)

(supplied)

Sealer (supplied)

Flare insulator (supplied)

Tube insulator

(not supplied)

Heat resistant

120°C or above

Vin

l clamps (supplied)

Flare nut

The procedure used for

installing the insulator for

both wide and narrow

tubes is the same.

Seal

Flare

insulator

Vinyl

clamp

Insulation

tape

Refrigerant tubing and insulator

(not supplied)

Drain pipe and insulator

(not supplied)

Drain insulator

and clamp.

Large

(supplied)

Packing

clamp.

Small

hose band

(supplied)

Cosmetic

(finishing) tape

Wide tubing

Narrow tubing

Insulation

Balance tubing

Three tubes arranged together

Two tubes arranged together

If the exterior of the outdoor

unit valves has been finished

with a square duct covering,

make sure you allow suffi-

cient space to use the valves

and to allow the panels to be

attached and removed.

Fig. 5-10

Fig. 5-11

5-4. Taping the Tubes

(1) At this time, the refrigerant tubes (and electrical

wiring if local codes permit) should be taped

together with armoring tape in 1 bundle. To pre-

vent the condensation from overflowing the drain

pan, keep the drain hose separate from the

refrigerant tubing.

(2) Wrap the armoring tape from the bottom of the

outdoor unit to the top of the tubing where it

enters the wall. As you wrap the tubing, overlap

half of each previous tape turn.

(3) Clamp the tubing bundle to the wall, using 1

clamp approx. each meter. (Fig. 5-10)

Do not wind the armoring tape too tightly since this

will decrease the heat insulation effect. Also ensure

that the condensation drain hose splits away from the

bundle and drips clear of the unit and the tubing.

5-5. Finishing the Installation

After finishing insulating and taping over the tubing,

use sealing putty to seal off the hole in the wall to pre-

vent rain and draft from entering. (Fig. 5-11)

NOTE

Insulated tubes

Drain hose

Clamp

Tubin

Apply putty here

6. APPENDIX

■ Name of Parts (Indoor Unit)

■ Care and Cleaning

CAUTION

WARNING

1. For safety, be sure to turn the air conditioner off and also to disconnect the power before

cleaning.

2. Do not pour water on the indoor unit to clean it. This will damage the internal compo-

nents and cause an electric shock hazard.

1. Never use solvents or harsh chemicals when cleaning the indoor unit. Do not wipe plastic

parts using very hot water.

2. Some metal edges and the fins are sharp and may cause injury if handled improperly; be

especially careful when you clean these parts.

3. The internal coil and other components of the outdoor unit must be cleaned every year.

Consult your dealer or service center.

Air intake and outlet side Clean the air intake and outlet side of the indoor unit with a vacuum cleaner brush, or wipe them

(Indoor unit) with a clean, soft cloth.

Air filter

The air filter collects dust and other particles from the air and should be cleaned at regular intervals

as indicated in the table below or when the filter indication ( ) on the display of the remote control

unit (wired type) shows that the filter needs cleaning. If the filter gets blocked, the efficiency of the air

conditioner drops greatly.

1. Remove the air filter from the air intake grille.

2. Use a vacuum cleaner to remove light dust. If there is sticky dust on the filter, wash the

filter in lukewarm, soapy water, rinse it in clean water, and dry it.

Type Period

UMR Six months

The frequency with which the filter should be cleaned depends on the environment in which the

unit is used.

NOTE

04-235 AirCon_X-type 9/3/04 11:40 AM Page 19

Water drain

Air outlet

Air filter

1. 2.

Care: After a prolonged idle period

Care: Before a prolonged idle period

Check the indoor and outdoor unit air intakes and outlets for blockage; if there is a

blockage, remove it.

• Operate the fan for half a day to dry out the inside.

• Disconnect the power supply and also turn off the circuit breaker.

• Clean the air filter and replace it in its original position.

• Outdoor unit internal components must be checked and cleaned periodically. Con-

tact your local dealer for this service.

CAUTION

1. Certain metal edges and the condenser fins are sharp and may cause injury if handled

improperly; special care should be taken when you clean these parts.

2. Periodically check the outdoor unit to see if the air outlet or air intake is clogged with dirt

or soot.

3. The internal coil and other components of the outdoor unit must also be cleaned periodi-

cally. Consult your dealer or service center.

■ Troubleshooting

If your air conditioner does not work properly, first check the following points before requesting service. If it still does not work

properly, contact your dealer or a service center.

Air conditioner does not run at all

1. Power failure.

After a power outage, press ON/

OFF operation

button

on the

wired remote control unit.

2. Leakage circuit breaker has

tripped.

2. Contact service center.

3. Line voltage is too low.

3. Consult your electrician or dealer.

4. Operation button is turned off.

4. Press the button again.

5. The wired remote control unit or

heat pump is

(

The inspection mark and the

letters E, F,

H, L, P in

combination with numbers

appear

the LCD of the wired

remote control unit.)

5. Consult your dealer.

Compressor runs but soon stops

1. Obstruction in front of condenser

coil

1. Remove obstruction

Poor cooling (or heating)

performance

1. Dirty or clogged air filter.

1. Clean air filter to improve the

2. Heat source or many people in

room.

2. Eliminate heat source if possible.

3. Doors and/or windows are open.

3. Shut them to keep the heat (or

cold) out.

4. Obstacle near air intake or air

discharge port.

4. Remove it to ensure good airflow.

5. Thermostat is set too high for

(or too low for heating).

5. Set the temperature lower (or

higher).

6. (Defrosting system does not work.)

6. (Consult your dealer.)

Trouble

Possible Cause

Remedy

airflow.

cooling

malfunctioning.

■ Tips for Energy Saving

Avoid

• Do not block the air intake and outlet of the unit. If either is obstructed, the unit

will not work well, and may be damaged.

• Do not let direct sunlight into the room. Use sunshades, blinds or curtains. If the walls

and ceiling of the room are warmed by the sun, it will take longer to cool the room.

• Always try to keep the air filter clean. (Refer to “Care and Cleaning.”) A clogged filter

will impair the performance of the unit.

• To prevent conditioned air from escaping, keep windows, doors and any other open-

ings closed.

Should the power fail while the unit is running

If the power supply for this unit is temporarily cut off, the unit will automatically resume operation once power is

restored using the same settings before the power was interrupted.

NOTE

04-235 AirCon_X-type 9/3/04 11:40 AM Page 20

■ Nom des pièces (unité intérieure)

■ Entretien et nettoyage

ATTENTION

AVERTISSEMENT

1. Pour toute sécurité, éteignez le climatiseur et débranchez-le de la prise secteur.

2. Ne versez pas d’eau sur l’unité intérieure pour la nettoyer. Cela pourrait abîmer les com-

posants internes et provoquer des décharges électriques.

1. Ne utilisez jamais de dissolvants ni de produits chimiques puissants lorsque l’unité

intérieure est nettoyée. N’essuyez pas les pièces en plastique avec de l’eau très chaude.

2. Certains bords métalliques et les ailettes étant coupants, ils doivent être manipulés avec

précaution lors du nettoyage sous peine de provoquer des blessures.

3. La bobine interne et les autres composants de l’unité extérieure doivent être nettoyés

tous les ans. Consultez le concessionnaire ou un service après-vente.

Nettoyez l’arrivée d’air et la sortie de l’unité intérieure avec la brosse d’un aspirateur ou les

essuyer avec un chiffon propre et doux.

Filtre à air

Le filtre à air recueille la poussière et les particules se trouvant dans l’air et doit être nettoyé à inter-

valles réguliers comme indiqué dans le tableau cidessous ou lorsque le symbole du filtre ( )

affiché sur la télécommande (avec fil) indique que le filtre doit être nettoyé. Si le filtre est bloqué,

l’efficacité du climatiseur diminue nettement.

1. Retirez le filtre à air de la grille de l’arrivée d’air.

2. Se servir d’un aspirateur pour enlever la poussière légère. Si de la poussière adhère au

filtre, lavez celui-ci dans de l’eau tiède et savonneuse, puis rincez-le dans de l’eau propre

et séchez-le.

Type Période

UMR Six mois

La fréquence de nettoyage du filtre dépend de l’environnement dans lequel l’unité est utilisée.

REMARQUE

L’arrivée d’air et la sortie d’air

(unité intérieure)

04-235 AirCon_X-type 9/3/04 11:40 AM Page 21

Drain

Sortie díair

Filtre à air

1. 2.

Entretien : après une période d’inactivité

prolongée

Entretien : avant une période d’inactivité

prolongée

Vérifiez l’arrivée d’air et la sortie d’air des unités intérieure et extérieure et

assurez-vous qu’elles ne sont pas obstruées ; si elles sont obstruées, remédiez

à ce problème.

• Faites fonctionner le ventilateur pendant une demi-journée pour faire sécher

l’intérieur de l’unité.

• Débranchez l’alimentation et mettez le disjoncteur en position arrêt.

• Nettoyez le filtre à air et remettez-le dans sa position initiale.

• Les éléments internes de l’unité extérieur doivent être vérifiés et nettoyés

régulièrement. Contactez votre distributeur le plus proche pour effectuer ces

opérations.

ATTENTION

1. Certains bords métalliques et les ailettes du condensateur étant coupants, ils doivent être

manipulés avec précaution lors du nettoyage sous peine de provoquer des blessures.

2. Vérifiez régulièrement que la sortie et l’arrivée d’air ne soient pas obstruées par de la

poussière ou de la suie.

3. La bobine interne et les autres composants de l’unité extérieure doivent être nettoyés

régulièrement. Consultez le concessionnaire ou un service après-vente.

04-235 AirCon_X-type 9/3/04 11:40 AM Page 22

■ Conseils pour économiser l’énergie

À éviter

Choses à faire

• Obstruer les arrivées et les sorties d’air de l’appareil. Si elles sont bouchées,

l’appareil ne fonctionnera pas de façon satisfaisante et il risque d’être endom-

magé.

• Laisser le soleil pénétrer directement dans la pièce. Utiliser des persiennes ou des

rideaux. Si les murs et le plafond de la pièce sont chauds sous l’action du soleil, il faudra

plus longtemps pour refroidir la pièce.

• Toujours maintenir le filtre à air propre. (Voir “Entretien et nettoyage”) Un filtre obstrué

risque d’affecter le fonctionnement de l’unité.

• Pour éviter que l’air refroidi ne s’échappe, maintenir toutes les fenêtres, portes et autres

ouvertures fermées.

Si une panne de courant se produit lorsque l’unité fonctionne

Si l’alimentation de cette unité est temporairement arrêtée, l’unité se remettra en marche, après rétablissement

de l’alimentation, avec les mêmes réglages qu’avant la panne de courant.

REMARQUE

■ Guide de dépannage

Si le climatiseur ne fonctionne pas correctement, effectuez les vérifications suivantes avant de faire appel à un réparateur. Si le

problème persiste, prenez contact avec votre concessionnaire ou avec un service après-vente.

Panne Cause possible Remède

Le climatiseur ne fonctionne pas du

tout.

1. Coupure de courant. 1. Après une panne de courant,

appuyez sur le bouton de marche/

arrêt de fonctionnement de la

télécommande avec fil.

2. Le disjoncteur a fonctionné. 2. Prenez contact avec un service

après-vente.

3. Tension de ligne trop basse. 3. Consultez un électricien ou le

concessionnaire.

4. Le bouton de fonctionnement est en

position Off.

4. Appuyez à nouveau sur le bouton.

5. La télécommande avec fil ou la

pompe thermique ne fonctionne pas

correctement.

(La marque díinspection et les

lettres E, F, H, L, P ainsi que des

numéros apparaissent sur l’affichage

à cristaux liquides de la

télécommande avec fil.)

5. Consultez le concessionnaire.

Le compresseur se met en marche

mais il s’arrÍte aussitôt.

1. Il y a un obstacle devant la bobine du

condensateur.

1. Retirez ce qui fait obstruction.

Refroidissement (ou chauffage)

insuffisant.

1. Filtre à air sale ou obstrué. 1. Nettoyez le filtre à air afin

díaméliorer la circulation díair.

2. Source de chaleur ou trop de monde

dans la pièce.

2. Si possible, éliminez la source de

chaleur.

3. Portes et/ou fenÍtres ouv ertes. 3. Fermez-les pour empÍcher la

pénétration d’air chaud (ou froid).

4. Obstacle devant l’arrivée ou la sortie

d’air.

4. Retirez líobstacle pour assurer une

bonne circulation d’air.

5. Le thermostat est réglé sur une

température trop élevée pour le

refroidissement (ou trop basse pour

le chauffage).

5. Réglez la température plus bas (ou

plus haut).

6. (Le dégivrage du système ne

fonctionne pas.)

6. (Consultez le concessionnaire

04-235 AirCon_X-type 9/3/04 11:40 AM Page 23

La page charge ...

Sanyo SPW-UMR124EXH56 Manuel utilisateur

Marque: Sanyo

Modèle: SPW-UMR124EXH56

Catégorie: Climatiseurs split-system

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Sanyo SPW-UMR124EXH56 User manual
português: Sanyo SPW-UMR124EXH56 Manual do usuário

Sanyo SPW-UMR124EXH56 Manuel utilisateur

Sanyo SPW-UMR124EXH56 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents