Schumacher DSR121DSR121 Le manuel du propriétaire

Marque: Schumacher

Modèle: DSR121DSR121

Catégorie: Chargeurs de batterie

Taper: Le manuel du propriétaire

0099001943-02

PLEASE SAVE THIS OWNERS MANUAL AND READ BEFORE EACH USE.

This manual will explain how to use the battery charger safely and effectively.

Please read and follow these instructions and precautions carefully.

POR FAVOR CONSERVE ESTE MANUAL DEL USUARIO Y LEALO ANTES

DE CADA USO. En este manual le explica cómo utilizar el cargador de batería

de manera segura y conable. Por favor, lea y siga las siguientes instrucciones

y precauciones.

GARDER LE MANUEL D’INSTRUCTION ET LISEZ LE AVANT CHAQUE

UTILISATION. Ce manuel explique comment utiliser le chargeur de batterie

d’une façon securitaire et efcace. S’il vous plaît lisez et suivez ces instructions

et precautions.

MODELS / MODELOS / MODÈLES :

DSR121, DSR122, DSR123, DSR124

Professional Wheel Charger

Cargador profesional con ruedas

Chargeur professionnel sur roues

OWNERS MANUAL / MANUAL DEL USUARIO / MANUEL D’UTILISATION

DSR124

CONTENTS

IMPORTANT SAFETY INSTRUCTIONS ...................................................................................... 5

PERSONAL SAFETY PRECAUTIONS ......................................................................................... 5

PREPARING TO CHARGE ........................................................................................................... 6

CHARGER LOCATION ................................................................................................................. 6

DC CONNECTION PRECAUTIONS ............................................................................................. 6

FOLLOW THESE STEPS WHEN BATTERY IS INSTALLED IN VEHICLE ................................... 6

FOLLOW THESE STEPS WHEN BATTERY IS OUTSIDE VEHICLE ........................................... 7

GROUNDING AND AC POWER CORD CONNECTIONS ........................................................... 7

ASSEMBLY INSTRUCTIONS ....................................................................................................... 7

CONTROL PANEL ......................................................................................................................... 8

OPERATING INSTRUCTIONS ...................................................................................................... 9

MAINTENANCE AND CARE ....................................................................................................... 12

ERROR CODES AND TROUBLESHOOTING ............................................................................ 13

BEFORE RETURNING FOR REPAIRS ...................................................................................... 15

SPECIFICATIONS ....................................................................................................................... 16

LIMITED WARRANTY ................................................................................................................. 17

WARRANTY CARD ..................................................................................................................... 47

CONTENIDOS

INSTRUCCIONES IMPORTANTES DE SEGURIDAD ................................................................ 18

PRECAUCIONES DE SEGURIDAD PERSONAL ....................................................................... 18

PREPARACIÓN PARA LA CARGA ............................................................................................ 19

UBICACIÓN DEL CARGADOR ................................................................................................... 19

PRECAUCIONES DE CONEXIÓN EN CC ................................................................................. 19

SIGA ESTOS PASOS CUANDO LA BATERÍA ESTÉ COLOCADA EN EL VEHÍCULO .............. 20

SIGA ESTOS PASOS CUANDO LA BATERÍA SE ENCUENTRE FUERA DEL VEHÍCULO ....... 20

CONEXIONES A TIERRA Y ENERGÍA DE CA ........................................................................... 21

INSTRUCCIONES DE MONTAJE ............................................................................................21

PANEL DE CONTROL ................................................................................................................. 22

INSTRUCCIONES DE OPERACIÓN .......................................................................................... 23

MANTENIMIENTO Y CUIDADO ................................................................................................. 27

CÓDIGOS DE ERROR Y LOCALIZACIÓN Y RESOLUCIÓN DE PROBLEMAS ....................... 27

ANTES DE DEVOLVER A REPARACIONES .............................................................................. 30

ESPECIFICACIONES ................................................................................................................. 31

GARANTÍA LIMITADA ................................................................................................................. 32

TARJETA DE GARANTÍA ............................................................................................................ 47

TABLE DES MATIÈRES

CONSIGNES DE SÉCURITÉ IMPORTANTES ........................................................................... 33

MESURES DE SÉCURITÉ PERSONNELLE .............................................................................. 33

PRÉPARATION POUR LE CHARGEMENT ................................................................................ 34

EMPLACEMENT DU CHARGEUR ............................................................................................. 34

PRÉCAUTIONS SUR LA CONNEXION C.C. .............................................................................. 34

ÉTAPES À SUIVRE QUAND LA BATTERIE EST INSTALLÉE DANS UN VÉHCULE ................ 34

ÉTAPES À SUIVRE QUAND LA BATTERIE EST INSTALLÉE HORS DU VÉHICULE ............... 35

MISE À LA TERRE ET CORDON D’ÉNERGIE CA ..................................................................... 35

DIRECTIVES D’ASSEMBLAGE .................................................................................................. 36

PANNEAU DE CONTRÔLE ........................................................................................................ 36

CONSIGNES D’UTILISATION ..................................................................................................... 38

MAINTENANCE ET ENTRETIEN ............................................................................................... 41

CODES D’ÉCHEC ET DÉPANNAGE .......................................................................................... 42

AVANT DE RETOURNER POUR LES RÉPARATIONS .............................................................. 45

SPÉCIFICATIONS ....................................................................................................................... 45

GARANTIE LIMITÉE ................................................................................................................... 46

CARTE DE GARANTIE ............................................................................................................... 48

• 5 •

1. IMPORTANT SAFETY INSTRUCTIONS

SAVE THESE INSTRUCTIONS.

1.1 SAVE THESE INSTRUCTIONS –

This manual contains important safety

and operating instructions.

1.2 Keep out of reach of children.

1.3 Do not expose the charger to rain or snow.

1.4 Use of an attachment not recommended

or sold by the battery charger

manufacturer may result in a risk of re,

electric shock or injury to persons.

1.5 To reduce the risk of damage to electric

plug and cord, pull by the plug rather than

the cord when disconnecting charger.

1.6 An extension cord should not be used

unless absolutely necessary. Use of

improper extension cord could result

in a risk of re and electric shock. If an

extension cord must be used, make sure:

• The pins on plug of extension cord are

the same number, size and shape as

those of plug on charger.

• The extension cord is properly wired and

in good electrical condition.

• The wire size is large enough for AC

ampere rating of charger as specied in

section 8.

1.7 Do not operate charger with damaged

cord or plug – replace the cord or plug

immediately.

1.8 Do not operate charger if it has received

a sharp blow, been dropped, or otherwise

damaged in any way; take it to a qualied

serviceman.

1.9 Do not disassemble charger; take it to

a qualied serviceman when service or

repair is required. Incorrect reassembly

may result in a risk of electric shock or re.

1.10 To reduce risk of electric shock, unplug

charger from outlet before attempting

any maintenance or cleaning. Turning off

controls will not reduce this risk.

1.11 WARNING:

RISK OF EXPLOSIVE GASES.

a. WORKING IN VICINITY OF A LEAD-

ACID BATTERY IS DANGEROUS.

BATTERIES GENERATE EXPLOSIVE

GASES DURING NORMAL BATTERY

OPERATION. FOR THIS REASON, IT IS

OF UTMOST IMPORTANCE THAT YOU

FOLLOW THE INSTRUCTIONS EACH

TIME YOU USE THE CHARGER.

b. To reduce risk of battery explosion,

follow these instructions and those

published by battery manufacturer

and manufacturer of any equipment

you intend to use in vicinity of battery.

Review cautionary markings on these

products and on engine.

2. PERSONAL SAFETY PRECAUTIONS

2.1 Consider having someone close enough

by to come to your aid when you work

near a lead-acid battery.

2.2 Have plenty of fresh water and soap

nearby in case battery acid contacts skin,

clothing, or eyes.

2.3 Wear complete eye protection and

clothing protection. Avoid touching eyes

while working near battery.

2.4 If battery acid contacts skin or clothing,

wash immediately with soap and water.

If acid enters eye, immediately ood

eye with running cold water for at least

10 minutes and get medical attention

immediately.

2.5 NEVER smoke or allow a spark or ame

in vicinity of battery or engine.

2.6 Be extra cautious to reduce risk of

dropping a metal tool onto battery. It might

spark or short-circuit battery or other

electrical part that may cause explosion.

2.7 Remove personal metal items such as

rings, bracelets, necklaces, and watches

when working with a lead-acid battery. A

lead-acid battery can produce a short-

circuit current high enough to weld a ring

or the like to metal, causing a severe burn.

2.8 Use charger for charging only LEAD-

ACID (STD, AGM or GEL) rechargeable

batteries with rated capacities of 24Ah

(6V) and 22-59Ah (12V). It is not intended

to supply power to a low voltage electrical

system other than in a starter-motor

application. Do not use battery charger

for charging dry-cell batteries that are

commonly used with home appliances.

These batteries may burst and cause

injury to persons and damage to property.

2.9 NEVER charge a frozen battery.

• 6 •

3. PREPARING TO CHARGE

3.1 If necessary to remove battery from

vehicle to charge, always remove

grounded terminal from battery rst. Make

sure all accessories in the vehicle are off,

so as not to cause an arc.

3.2 Be sure area around battery is well

ventilated while battery is being charged.

3.3 Clean battery terminals. Be careful to

keep corrosion from coming in contact

with eyes.

3.4 Add distilled water in each cell until

battery acid reaches level specied by

battery manufacturer. Do not overll. For a

battery without removable cell caps, such

as valve regulated lead acid batteries,

carefully follow manufacturer’s recharging

instructions.

3.5 Study all battery manufacturer’s

specic precautions while charging and

recommended rates of charge.

3.6 Determine voltage of battery by referring

to car owner’s manual and make sure that

output voltage selector switch is set at

correct voltage. If charger has adjustable

charge rate, charge battery initially at

lowest rate.

4. CHARGER LOCATION

4.1 Locate charger as far away from battery

as DC cables permit.

4.2 Never place charger directly above

battery being charged; gases from battery

will corrode and damage charger.

4.3 Never allow battery acid to drip on

charger when reading electrolyte specic

gravity or lling battery.

4.4 Do not operate charger in a closed-in

area or restrict ventilation in any way.

4.5 Do not set a battery on top of charger.

5. DC CONNECTION PRECAUTIONS

5.1 Connect and disconnect DC output clips

only after setting any charger switches to

“off” position and removing AC cord from

electric outlet. Never allow clips to touch

each other.

5.2 Attach clips to battery and chassis, as

indicated in sections 6 and 7.

6. FOLLOW THESE STEPS WHEN BATTERY IS INSTALLED IN VEHICLE

WARNING: A SPARK NEAR THE

BATTERY MAY CAUSE A BATTERY

EXPLOSION. TO REDUCE THE RISK OF

A SPARK NEAR THE BATTERY:

6.1 Position AC and DC cords to reduce risk

of damage by hood, door, or moving

engine part.

6.2 Stay clear of fan blades, belts, pulleys, and

other parts that can cause injury to persons.

6.3 Check polarity of battery posts. POSITIVE

(POS, P, +) battery post usually has larger

diameter than NEGATIVE (NEG, N,–) post.

6.4 Determine which post of battery is

grounded (connected) to the chassis. If

negative post is grounded to chassis (as

in most vehicles), see (6.5). If positive

post is grounded to the chassis, see (6.6).

6.5 For negative-grounded vehicle, connect

POSITIVE (RED) clip from battery charger

to POSITIVE (POS, P, +) ungrounded post

of battery. Connect NEGATIVE (BLACK)

clip to vehicle chassis or engine block

away from battery. Do not connect clip to

carburetor, fuel lines, or sheet-metal body

parts. Connect to a heavy gauge metal

part of the frame or engine block.

6.6 For positive-grounded vehicle, connect

NEGATIVE (BLACK) clip from battery

charger to NEGATIVE (NEG, N, –)

ungrounded post of battery. Connect

POSITIVE (RED) clip to vehicle chassis

or engine block away from battery. Do

not connect clip to carburetor, fuel lines,

or sheet-metal body parts. Connect to a

heavy gauge metal part of the frame or

engine block.

6.7 When disconnecting charger, turn

switches to off, disconnect AC cord,

remove clip from vehicle chassis, and

then remove clip from battery terminal.

6.8 See Operating Instructions for length of

charge information.

• 7 •

7. FOLLOW THESE STEPS WHEN BATTERY IS OUTSIDE VEHICLE

WARNING: A SPARK NEAR THE

BATTERY MAY CAUSE A BATTERY

EXPLOSION. TO REDUCE THE RISK OF

A SPARK NEAR THE BATTERY:

7.1 Check polarity of battery posts. POSITIVE

(POS, P, +) battery post usually has a larger

diameter than NEGATIVE (NEG, N, –) post.

7.2 Attach at least a 24-inch-long 6-gauge

(AWG) insulated battery cable to

NEGATIVE (NEG, N, –) battery post.

7.3 Connect POSITIVE (RED) charger clip to

POSITIVE (POS, P, +) post of battery.

7.4 Position yourself and free end of cable as

far away from battery as possible – then

connect NEGATIVE (BLACK) charger clip

to free end of cable.

7.5 Do not face battery when making nal

connection.

7.6 When disconnecting charger, always do

so in reverse sequence of connecting

procedure and break rst connection

while as far away from battery as

practical.

7.7 A marine (boat) battery must be removed

and charged on shore. To charge it on

board requires equipment specially

designed for marine use.

8. GROUNDING AND AC POWER CORD CONNECTIONS

8.1 This battery charger is for use on a

nominal 120 volt circuit. The plug must

be plugged into an outlet that is properly

installed and grounded in accordance with

all local codes and ordinances. The plug

pins must t the receptacle (outlet). Do

not use with an ungrounded system.

8.2 DANGER: Never alter the AC cord or

plug provided – if it does not t the outlet,

have a proper grounded outlet installed

by a qualied electrician. An improper

connection can result in a risk of an

electric shock or electrocution.

NOTE: Pursuant to Canadian

Regulations, use of an adapter plug

is not allowed in Canada. Use of an

adapter plug in the United States is not

recommended and should not be used.

8.3 USING AN EXTENSION CORD

The use of an extension cord is not

recommended. If you must use an

extension cord, follow these guidelines:

• Pins on plug of extension cord must be

the same number, size, and shape as

those of plug on charger.

• Ensure that the extension cord is

properly wired and in good electrical

condition.

• Wire size must be large enough for

the AC ampere rating of charger, as

specied:

Length of cord (feet) 25 50 100 150

AWG* size of cord 16 12 10 8

*AWG-American Wire Gauge

9. ASSEMBLY INSTRUCTIONS

9.1 Remove all cord wraps and uncoil the

cables prior to using the battery charger.

9.2 Extend the handle from the retracted

position by pulling it upward until it locks

into place. (Press the small black buttons

inward, if necessary.)

9.3 Clamp cleat installation

1. Slide the short end of the cable clamp

cleat Z-bracket into the open slot.

There are 4 total slots: the top left

and top right, and the bottom left and

bottom right sides of the charger.

2. Insert the No. 8 screw into the open

hole below each slot, to fasten the

cable bracket in place.

NOTE: The screws are #8-18.

Use a 1/4˝ hex screwdriver.

• 8 •

10. CONTROL PANEL

NOTE: Some features are not available

on all models.

12V MEMORY SAVER PORT

(Models DSR122 and DSR124)

DIGITAL DISPLAY

The digital display indicates voltage, % of

charge, or amperage, depending on the

Display Mode chosen.

DISPLAY MODE BUTTON

Use to set the function of the digital

display to one of the following:

Volts – The digital display

shows the voltage at the charger’s

battery clamps.

Amps – The digital display shows

the charging current, in amps. When

in Boost mode, the display shows the

approximate output current, in amps.

Battery percentage – The digital

display shows an estimated charge

percentage of the battery connected to

the charger’s battery clamps.

CHARGING STATUS LEDS

REVERSED CLAMPS LED ashing:

The connections are reversed.

BOOST/CHARGING (yellow/orange)

LED lit: The charger has detected that a

battery is connected, and is performing the

selected operation – either Boost or Charge.

CHARGED/MAINTAINING (green)

LED lit: The battery is fully charged and

the charger is in Maintain mode.

NOTE: See Operating Instructions for a

complete description of the charger modes.

FLASH BUTTON

(Models DSR122 and DSR124)

Press to enter Flash Reprogramming mode.

UP/DOWN ARROW BUTTONS

Use to change any variable settings on

the display.

BATTERY VOLTAGE/

MEMORY SAVER BUTTON

Select 6V, 12V or 24V, or select

for the memory saver function.

BATTERY TYPE BUTTON

Use this button to select the battery type.

STD (Standard) – Used in cars, trucks

and motorcycles, these batteries have

vent caps and are often marked “low

maintenance” or “maintenance-free”.

This type of battery is designed to

deliver quick bursts of energy (such as

starting engines) and has a greater plate

count. The plates are thinner and have

somewhat different material composition.

Standard batteries should not be used for

deep-cycle applications.

AGM – The Absorbed Glass Mat

construction allows the electrolyte to

be suspended in close proximity with

the plate’s active material. In theory,

this enhances both the discharge and

recharge efciency. The AGM batteries

are a variant of Sealed VRLA (valve

regulated lead-acid) batteries. Popular

uses include high-performance engine

starting, power sports, deep-cycle, solar

and storage batteries.

GEL – The Gel Cell is similar to the

AGM style because the electrolyte is

suspended, but different because the

AGM battery is still considered to be a

wet cell. The electrolyte in a GEL cell has

a silica additive that causes it to set up

or stiffen. The recharge voltages on this

type of cell are lower than the other styles

of lead-acid battery. This is probably the

most sensitive cell in terms of adverse

reactions to over-voltage charging. Gel

batteries are best used in very deep cycle

applications and may last a bit longer in

hot weather applications. If the incorrect

battery charger is used on a Gel Cell

battery, poor performance and premature

failure is certain.

• 9 •

OUTPUT RATE BUTTON

Select one of the following rates:

Maintain (4A)

For charging small batteries and

maintaining fully charged large batteries.

Fast Charge (15A)

For charging automotive, marine and

light truck batteries.

Boost

Increases the voltage and sends a

quick burst of energy into the battery,

to quickly bring deeply discharged

batteries back to life.

Engine Start

Provides additional amps for cranking

an engine with a weak or run-down

battery. Always use in combination with

a battery.

START/STOP BUTTON

Begins and ends the Charge, Boost,

Engine Start, Flash Reprogram and

Memory Saver modes.

MAIN POWER SWITCH

This switch supplies power to the charger.

REPROGRAMMING

THE DEFAULT SETTINGS

(Models DSR122 and DSR124 only)

If you are satised with the default settings,

skip to Operating Instructions.

When you rst power up the charger, the

default settings are:

Display Mode – Volts

Battery Voltage – 12V

Battery Type – Standard

Output Rate – Maintain (4A)

To change the power up default settings:

1. Change to the desired Display Mode,

Battery Voltage, Battery Type and

Output Rate.

2. Press and hold both Up and Down

Arrow buttons at the same time until

the LEDs stop ashing.

3. The next time you power up the unit,

these settings will be saved and

become the startup default settings.

11. OPERATING INSTRUCTIONS

WARNING: A spark near the battery may

cause an explosion.

IMPORTANT: Do not start the vehicle with

the charger connected to the AC outlet

(except during Engine Start), or it could

damage the charger.

CHARGING A BATTERY IN THE VEHICLE

1. Turn off all the vehicle’s accessories.

2. Keep the hood open.

3. Clean the battery terminals.

4. Place the charger on a dry, non-

ammable surface.

5. Lay the AC/DC cables away from any

fan blades, belts, pulleys and other

moving parts.

6. Connect the battery, following the

precautions listed in sections 6 and 7.

7. Connect the charger to an electrical

outlet.

8. Set Battery Voltage to 6V or 12V.

NOTE: 24V is available only on models

DSR123 and DSR124, for Boost and

Engine Start.

CAUTION:

Always visually conrm the voltage of the

battery being charged. Not doing so can

cause damage to the battery and vehicle’s

electrical system. Other property damage

or personal injury may occur.

9. Set Battery Type to STANDARD,

AGM, or GEL. (If unsure, consult the

label on the battery or the battery

manufacturer.)

10. Set Output Rate to

Maintain (4A),

Fast Charge (15A) or Boost.

11. Charging will start when the START/

STOP button is pressed and nish

automatically.

12. Charged/Maintaining (green) LED

will light when nished and charger will

maintain battery.

13. To stop the battery maintaining process,

press the START/STOP button.

14. When charging is complete, disconnect

the charger from the AC power, remove

the clamps from the vehicle’s chassis,

and then remove the clamp from the

battery terminal.

CHARGING A BATTERY

OUTSIDE OF THE VEHICLE

1. Place battery in a well-ventilated area.

2. Clean the battery terminals.

3. Connect the battery, following the

precautions listed in sections 6 and 7.

4. Connect the charger to the electrical

outlet.

5. Set Battery Voltage to 6V or 12V.

NOTE: 24V is available only on models

DSR123 and DSR124, for Boost and

Engine Start.

CAUTION:

Always visually conrm the voltage of the

battery being charged. Not doing so can

cause damage to the battery and vehicle’s

electrical system. Other property damage

or personal injury may occur.

• 10 •

6. Set Battery Type to STANDARD, AGM,

or GEL. (If unsure, consult the label on

the battery or the battery manufacturer.)

7. Set Output Rate to

Maintain (4A),

Fast Charge (15A) or Boost.

8. Charging will start when the START/

STOP button is pressed and nish

automatically.

9. Charged/Maintaining

(green) LED

will light when nished and charger will

maintain battery.

10. To stop the battery maintaining process,

press the START/STOP button.

11. When charging is complete,

disconnect the charger from the AC

power, disconnect the negative clamp,

and nally the positive clamp.

12. A marine (boat) battery must be

removed and charged on shore.

BATTERY CHARGING TIMES

APPLICATION

BATTERY

SIZE

CHARGING TIME (Hours)

2A 6A 8A 10A

POWERSPORTS

6Ah 6

32 Ah 15

AUTOMOTIVE

300 CCA 12

1000 CCA 30

MARINE

50 Ah 15

105Ah 33

1.75

4.5

3.5

8.5

4.25

9.5

1.5

3.5

Times are based on a 50% discharged battery

and may change, depending on age and condition

of battery.

DESULFATION

If the battery is left discharged for an

extended period of time, it could become

sulfated and not accept a normal charge.

If the charger detects a sulfated battery,

the charger will switch to a special mode

of operation designed for such batteries

(6V/12V only). If successful, normal

charging will resume after the battery is

desulfated. Desulfation could take up to

10 hours. If desulfation fails, charging will

abort and the display will show the error

message F02.

ABORTED CHARGE

If charging cannot be completed normally,

charging will abort. When charging aborts,

the charger’s output is shut off, and

the display will show an error code. Do

not continue attempting to charge this

battery. Check the battery and replace, if

necessary.

CHARGE COMPLETION AND MAINTAIN

MODE (FLOAT MODE MONITORING)

Charge completion is indicated by the

green Charged/Maintaining LED.

This means that the charger has stopped

charging and has switched to the Maintain

Mode of operation. NOTE: If the charger

has to provide its maximum maintain

current for a continuous 12 hour period,

it will go into Abort Mode (see Aborted

Charge section). This is usually caused by

a drain on the battery, or the battery could

be bad. Make sure there are no loads on

the battery. If there are, remove them. If

there are none, have the battery checked

or replaced.

MAINTAINING A BATTERY

The charger maintains 6V and 12V

batteries, keeping them at full charge.

NOTE: The maintain mode technology

allows you to safely charge and maintain

a healthy battery for extended periods

of time. However, problems with the

battery, electrical problems in the

vehicle, improper connections or other

unanticipated conditions could cause

excessive current draws. As such,

occasionally monitoring your battery and

the charging process is required.

USING BOOST MODE

1. Set Battery Voltage to 6V, 12V or 24V.

CAUTION:

Always visually conrm the voltage of the

battery being charged. Not doing so can

cause damage to the battery and vehicle’s

electrical system. Other property damage

or personal injury may occur.

NOTE: Additional safety settings have

been added to the charger software.

When the unit is in the 24 volt mode, the

voltage boost output will not activate if

battery voltage is less than 15.5 volts. If

a 24 volt battery has voltage below 15.5

volts, the voltage will be shown on the

digital display and the “Volts” and “24V”

LEDs will ash.The START/STOP button

must be pressed again after conrmation

that the unit is operating on a 24V system.

2. Set Battery Type to STANDARD, AGM,

or GEL. (If unsure, consult the label on

the battery or the battery manufacturer.)

3. Set Output Rate to

Boost.

NOTE: This mode should not be used

for smaller batteries (lawn tractor,

motorcycle, etc.).

4. Boost will start when the START/STOP

button is pressed and will hold batteries

at the following voltages:

6V: held at 6.8V

12V: held at 13.6V

24V: held at 27.3V

5. Boost will end when the START/STOP

button is pressed.

• 11 •

USING ENGINE START MODE

Your battery charger can be used to jump

start your car if the battery is low. Follow

all safety instructions and precautions for

charging your battery. Wear complete eye

protection and protective clothing.

WARNING: Using Engine Start mode

WITHOUT a battery installed in the

vehicle could cause damage to the

vehicle’s electrical system.

NOTE: If you have charged the battery

and it still will not start your car, do

not use Engine Start mode, or it could

damage the vehicle’s electrical system.

Have the battery checked.

1. With the charger unplugged from the

AC outlet, connect the charger to the

battery, following the instructions given

in sections 6 and 7.

2. Set the Battery Voltage to 6V, 12V or 24V.

3. Set the Output Rate to Engine Start.

NOTE: The charger will supply charge to

the battery before cranking.

4. Press the START/STOP button.

The digital display will show On

for 2 minutes.

5. Crank the vehicle when the digital

display shows rdy. Do not crank for

longer than 20 seconds.

NOTE: During extremely cold weather,

or if the battery is under one volt, charge

the battery for 5 minutes before cranking

the engine.

6. Wait three minutes before attempting

to start again. The digital display will

indicate the time remaining before

cranking again.

NOTE: During this cool down period,

the charger is supplying the battery

with a charge of up to 15A.

7. When the digital display times down to

0 and reads rdy, the Boost/Charging

LED is on, you are ready to crank

the vehicle again. You have three

minutes to perform an engine start

(Pressing the START/STOP button is

NOT REQUIRED.)

8. If the engine still does not start, allow

the charger to charge the battery for ve

more minutes before cranking it again.

9. After the engine starts, unplug the AC

power cord before disconnecting the

battery clamps from the vehicle.

NOTE: If the engine does turn over but

never starts, there is not a problem with

the starting system; there is a problem

somewhere else with the vehicle. STOP

cranking the engine until the other problem

has been diagnosed and corrected.

FLASH REPROGRAMMING

(Models DSR122 and DSR124)

NOTE: Do not attempt to Flash Reprogram

a vehicle that has a discharged or

defective battery. Make sure that the

vehicle battery is in good condition and

FULLY CHARGED before proceeding.

The charger is designed to supply up to

100A in “Flash Reprogram” mode.

Some newer vehicles may require more

than 100A while ash reprogramming the

ECU. Consult the vehicle manufacturer’s

specications to determine the required

amperage. The charger’s “Flash

Reprogram” mode cannot be used on

vehicles that require more than 100A,

or damage to the ECU and/or vehicle’s

electrical system may occur. Failure to

follow these instructions may also damage

the service center’s ash reprogram

equipment.

1. Set the mode to Flash.

2. Use (Up) and (Down) buttons

to adjust the voltage needed for the

vehicle being programmed (refer to

OEM specications). Voltage selected

is shown on the digital display. The

unit has a voltage range of 13.0 to

15.0, with a default of 14.2.

NOTE: When the

Volts LED stops

blinking, the display shows the selected

voltage.

3. Press START/STOP to activate the

output.

NOTE: During this time, the other buttons

will not work until you turn off the output.

When the display shows OFF, no buttons will

work for ve seconds; then it automatically

goes back to the default state.

4. When nished with Flash Reprogramming,

press START/STOP to exit this mode.

NOTE: The clamps are live during Flash

Reprogramming.

• 12 •

BATTERY PERCENTAGE

Press the Display Mode button to

switch from

battery voltage to

current or

battery percentage.

USING A MEMORY SAVER

(Models DSR122 and DSR124)

Use a memory saver to save the vehicle’s

on-board diagnostic computer settings (radio

programs, diagnostic codes, etc.) while the

battery is disconnected from the vehicle

during repair or maintenance.

NOTE: The 12V port is rated at 15A; the

provided OBDII cable has an 8A fuse.

IMPORTANT!

Some vehicle manufacturers do not allow

the use of a memory saver through the

OBDII. Consult the vehicle manufacturer

before use, to determine if a memory

saver is acceptable for use on the vehicle.

1. Make sure that Charge/Boost/Engine

Start are off. Do not operate or crank

when using a memory saver. Do not

charge a battery when operating the

memory saver

2. Turn off the vehicle and make sure all

accessories are off.

3. Wait at least 30 minutes before using

the memory saver. This ensures that

the accessories are no longer drawing

current from the car battery.

4. Connect the memory saver’s 12V

connector to 12V port on the charger.

5. Press the

button until the

Memory Saver LED is lit.

6. Connect the memory saver’s OBD

connector to the vehicle’s OBD plug.

Make sure the connector is fully

engaged.

7. Push the START/STOP button.

8. Disconnect the vehicle’s battery

cables and cover the positive and

negative cables with an insulator,

such as electrical tape. This prevents

the connectors from touching metal,

each other, or the chassis and causing

a short circuit, due to the vehicle’s

electrical system receiving power from

the memory saver through the OBD

connection.

WARNING:

When working with the vehicle’s battery,

review all of the battery manufacturer’s

safety instructions, warnings and

directives regarding battery disconnection,

removal and replacement.

9. Remove the old battery and put the new

battery into position.

10. Remove the insulator from the positive

cable and connect it to the positive

terminal of the new battery.

11. Remove the insulator from the negative

cable and connect it to the negative

terminal of the new battery.

12. Press the START/STOP button to turn

off the memory saver.

13. Once the new battery is connected,

unplug the memory saver’s OBD

connector from the vehicle’s OBD plug.

12. MAINTENANCE AND CARE

A minimal amount of care can keep your

battery charger working properly for years.

• Clean the clamps each time you are

nished charging. Wipe off any battery

uid that may have come in contact with

the clamps to prevent corrosion.

• Occasionally cleaning the case of the

charger with a soft cloth will keep the

nish shiny and help prevent corrosion.

• Coil the input and output cords neatly

when storing the charger. This will help

prevent accidental damage to the cords

and charger.

• Store the charger unplugged from the AC

power outlet in an upright position.

• Store inside, in a cool, dry place. Do not

store the clamps on the handle, clipped

together, on or around metal, or clipped to

the cables.

• 13 •

13. ERROR CODES AND TROUBLESHOOTING

Error Codes

CODE DESCRIPTION REASON/SOLUTION

F 01

The battery voltage is still under 10V

(for a 12V battery) or 5V (for a 6V

battery) after 2 hours of charging.

The battery could be bad. Have it checked or replaced.

SUL

The charger has detected a sulfated

battery.

The charger will go into desulfation mode. If the

desulfation is not successful after 10 hours, the charger

will go into abort mode.

F02

The charger cannot desulfate the

battery.

The battery could not be desulfated; have it checked or

replaced.

F03

The battery was unable to reach the

“full charge” voltage.

May be caused by trying to charge a large battery or

bank of batteries on too low of a current setting. Try

again with a higher current setting or have the battery

checked or replaced.

F04

The connections to the battery are

reversed.

The battery is connected backwards. Unplug the charger

and reverse the connections to the battery.

F05

The charger was unable to keep

the battery fully charged in maintain

mode.

The battery won’t hold a charge. May be caused by a drain

on the battery or the battery could be bad. Make sure there

are no loads on the battery. If there are remove them. If

there are none, have the battery checked or replaced.

F06

The charger detected that the battery

may be getting too hot (thermal

runaway).

The charger automatically shuts the current off if it

detects the battery may be getting too hot. Have the

battery checked or replaced.

If you get an error code, check the connections and settings and/or replace the battery.

Troubleshooting

PROBLEM POSSIBLE CAUSE SOLUTION

No reading or 0.0V

shown on the display.

Clamps are not making a

good connection.

AC cord and/or extension

cord is loose.

No power at receptacle.

Clamp polarity reversed.

Check for poor connection at

battery and frame. Make sure

connecting points are clean.

Check power cord and extension

cord for loose tting plug.

Check for open fuse or circuit

breaker supplying AC outlet.

Verify and reverse the battery

clamps.

The

Boost/Charging

LED does not turn off.

The charger is still in Boost

mode.

The charger is still in one of

the charge modes.

This is normal. In Boost mode, the

LED will not turn off until the

battery is disconnected from the

charger.

This is normal. In one of the charge

modes, the LED will not turn off

until the battery charging process

is completed.

• 14 •

PROBLEM POSSIBLE CAUSE SOLUTION

Short or no start cycle

when cranking engine.

Failure to wait 3 minutes (180

seconds) between cranks.

Clamps are not making a

good connection.

AC cord and/or extension

cord is loose.

No power at receptacle.

The charger may be

overheated.

Battery may be severely

discharged.

Wait three minutes or until the

display reads rdy and the

LED is on.

Check for poor connection at

battery and frame. Make sure

connecting points are clean.

Check power cord and extension

cord for loose tting plug.

Check for open fuse or circuit

breaker supplying AC outlet.

The internal thermal protector may

have tripped and needs

a little longer to close. Wait until it

automatically resets and try again.

On a severely discharged battery,

use the

Boost rate for 10 to 15

minutes, to help assist in cranking.

Charger makes a loud

buzz.

Transformer laminations

vibrate.

No problem; this is a normal

condition.

Battery % stays low

during charging.

Battery is severely

discharged.

Wrong battery voltage

selected.

Continue charging battery for two

more hours. If problem continues,

have the battery checked and

replace, if necessary.

Make sure Battery Voltage switch

is set to the correct voltage for the

battery you are charging.

The “Maintain” and “Fast

Charge” rates do not

work on the 24V setting.

Complete charge of a 24 Volt

battery is not a function of

this unit.

This charger does not fully charge

24V batteries. It boosts the voltage

to 27.3V and holds the voltage at

this level.

Clicking noise from

charger.

Circuit breaker is cycling.

Battery is defective.

Shorted battery clamps.

Severely discharged battery,

but otherwise a good battery.

Reversed connections at

battery.

Under certain conditions, this unit

has a high capacity and the circuit

breaker protects the unit under

these conditions. If the circuit

breaker is cycling often, stop the

operation by pressing the START/

STOP button and wait until the unit

has cooled, to return to operation.

Have the battery checked.

Circuit breaker cycles when current

draw is too high. Check for shorted

cables and replace if necessary.

Allow charging to continue until

battery has a chance to recover

sufciently to take a charge. If more

than 20 minutes, stop charging and

have the battery checked.

Correct the lead connections.

• 15 •

PROBLEM POSSIBLE CAUSE SOLUTION

Display shows “SUL” The battery is sulfated. A sulfated battery may eventually

take a normal charge if left

connected. The charger will continue

to charge with a low current for up to

10 hours to recover the battery. If the

battery will not take a charge after 10

hours, have it checked.

Engine start does not

work.

Vehicle drawing more than

the Engine Start rate.

Failure to wait 3 minutes (180

seconds) between cranks.

The charger may be

overheated.

Battery may be severely

discharged.

Crank time varies with the amount

of current drawn. If cranking draws

more than the Engine Start rate,

crank time may be reduced.

When the Engine Start LED

blinks, wait 3 minutes of rest time

before the next crank.

The thermal protector may have

tripped and needs a little longer to

reset. Make sure the charger vents

are not blocked. Wait and try again.

On a severely discharged battery,

use the

Boost rate for 10 to 15

minutes, to help assist in cranking.

14. BEFORE RETURNING FOR REPAIRS

If these solutions do not eliminate the problem,

or for more information about troubleshooting,

contact customer service for assistance:

[email protected]

www.batterychargers.com

or call 1-800-621-5485

For REPAIR OR RETURN, contact Customer Service at 1-800-621-5485. DO NOT SHIP

UNIT until you receive a RETURN MERCHANDISE AUTHORIZATION (RMA) number

from Customer Service at Schumacher Electric Corporation.

• 16 •

15. SPECIFICATIONS

DSR121

Input .......................................................................................120V AC 60Hz, 12.5A cont., 50A int.

Output ............................................................................................................. 12V DC, 4/15A cont.

50A int. (30 sec. max. ON, 60 sec. min. OFF)

250A int. (5 sec. max. ON, 180 sec. min. OFF)

cUL

Input .......................................................................................120V AC 60Hz, 12.5A cont., 50A int.

Output ............................................................................................................. 12V DC, 4/15A cont.

45A int. (30 sec. max. ON, 60 sec. min. OFF)

250A int. (5 sec. max. ON, 180 sec. min. OFF)

DSR122

Input .......................................................................................120V AC 60Hz, 12.5A cont., 49A int.

Output .......................................................................................................... 6/12V DC, 4/15A cont.

60A int. (60 sec. max. ON, 120 sec. min. OFF

275A int. (5 sec. max. ON, 180 sec. min. OFF)

DSR123

Input .......................................................................................120V AC 60Hz, 12.5A cont., 60A int.

Output ............................................................................................................. 12V DC, 4/15A cont.

12V DC: 50A int. (60 sec. max. ON, 120 sec. min. OFF)

250A int. (5 sec. max. ON, 180 sec. min. OFF)

24V DC: 30A int. (60 sec. max. ON, 120 sec. min. OFF)

150A int. (5 sec. max. ON, 180 sec. min. OFF)

DSR124

Input ................................................................................... 120V AC 60Hz, 12.5A cont., 66.5A int.

Output .......................................................................................................... 6/12V DC, 4/15A cont.

80A int. (120 sec. max. ON, 120 sec. min. OFF)

..............................................................................330A int. (5 sec. max. ON, 180 sec. min. OFF)

24V DC: 30A cont.; 250A int. (5 sec. max. ON, 180 sec. min. OFF)

• 17 •

16. LIMITED WARRANTY

WARRANTY NOT VALID IN MEXICO.

SCHUMACHER ELECTRIC CORPORATION, 801 BUSINESS CENTER DRIVE,

MOUNT PROSPECT, IL 60056-2179, MAKES THIS LIMITED WARRANTY TO THE

ORIGINAL RETAIL PURCHASER OF THIS PRODUCT. THIS LIMITED WARRANTY

IS NOT TRANSFERABLE OR ASSIGNABLE.

Schumacher Electric Corporation (the “Manufacturer”) warrants this battery charger

for two (2) years from the date of purchase at retail against defective material or

workmanship that may occur under normal use and care. If your unit is not free from

defective material or workmanship, Manufacturer’s obligation under this warranty is

solely to repair or replace your product with a new or reconditioned unit at the option

of the Manufacturer. It is the obligation of the purchaser to forward the unit, along with

proof of purchase and mailing charges prepaid to the Manufacturer or its authorized

representatives in order for repair or replacement to occur.

Manufacturer does not provide any warranty for any accessories used with this product

that are not manufactured by Schumacher Electric Corporation and approved for use

with this product. This Limited Warranty is void if the product is misused, subjected

to careless handling, repaired, or modied by anyone other than Manufacturer or if

this unit is resold through an unauthorized retailer. Manufacturer may void this Limited

Warranty if a “warranty may be void if removed” label is removed from the product.

Manufacturer makes no other warranties, including, but not limited to, express, implied or

statutory warranties, including without limitation, any implied warranty of merchantability

or implied warranty of tness for a particular purpose. Further, Manufacturer shall

not be liable for any incidental, special or consequential damage claims incurred by

purchasers, users or others associated with this product, including, but not limited to,

lost prots, revenues, anticipated sales, business opportunities, goodwill, business

interruption and any other injury or damage. Any and all such warranties, other than the

limited warranty included herein, are hereby expressly disclaimed and excluded. Some

states do not allow the exclusion or limitation of incidental or consequential damages or

length of implied warranty, so the above limitations or exclusions may not apply to you.

This warranty gives you specic legal rights and it is possible you may have other rights

which vary from this warranty.

THIS LIMITED WARRANTY IS THE ONLY EXPRESS LIMITED WARRANTY AND THE

MANUFACTURER NEITHER ASSUMES OR AUTHORIZES ANYONE TO ASSUME

OR MAKE ANY OTHER OBLIGATION TOWARDS THE PRODUCT OTHER THAN

THIS WARRANTY.

Schumacher

and the Schumacher logo are registered trademarks

of Schumacher Electric Corporation.

• 18 •

1. INSTRUCCIONES IMPORTANTES DE SEGURIDAD

GUARDE ESTAS INSTRUCCIONES.

1.1 GUARDE ESTAS INSTRUCCIONES –

Este manual contiene instrucciones

operativas y de seguridad de importancia.

1.2 Manténgase alejado de los niños.

1.3 No exponga el cargador a la lluvia

o a la nieve.

1.4 El uso de un accesorio no recomendado

o suministrado por por el fabricante del

cargador de baterías puede provocar

riesgo de incendio, descarga eléctrica o

lesiones a personas.

1.5 Para reducir el riesgo de daños al

enchufe o cable eléctrico, jale del enchufe

en lugar de jalar del cable al desconectar

el cargador.

1.6 No se debe utilizar un alargador a menos

que resulte absolutamente necesario. El

uso de un alargador inadecuado puede

provocar riesgo de incendio o descarga

eléctrica. En caso de que deba utilizarse

un alargador, asegúrese de que:

• Los pasadores en el enchufe del

alargador posean el mismo número,

tamaño y forma que aquellos presentes

en el enchufe del cargador.

• El alargador se encuentre correctamente

conectado y en buenas condiciones

eléctricas; y

• El tamaño del cable sea lo

sucientemente extenso para el

amperaje en CA del cargador como se

especica en la sección 8.

1.7 No utilice el cargador si el mismo posee

un enchufe o cable dañado; substituya el

cable o el enchufe inmediatamente por

una persona calicada en el ramo.

1.8 No utilice el cargador si el mismo recibió

un golpe fuerte, si se cayó o si sufrió

daños de cualquier otra forma; hágalo

revisar por una persona capacitada que

efectúe reparaciones.

1.9 No desarme el cargador; hágalo revisar

por una persona capacitada que efectúe

reparaciones cuando necesite servicio

de mantenimiento o una reparación.

Volver a ensamblar el cargador en forma

incorrecta puede provocar riesgo de

incendio o descarga eléctrica.

1.10 Para reducir el riesgo de descarga

eléctrica, desenchufe el cargador del

tomacorriente antes de intentar llevar a

cabo cualquier actividad de mantenimiento

o limpieza. El simple apagado de los

controles no reducirá este riesgo.

1.11 ADVERTENCIA:

RIESGO DE GASES EXPLOSIVOS.

a. RESULTA PELIGROSO TRABAJAR EN

FORMA CERCANA A UNA BATERÍA DE

PLOMO. LAS BATERÍAS GENERAN

GASES EXPLOSIVOS DURANTE

SU NORMAL FUNCIONAMIENTO.

POR ESTE MOTIVO, RESULTA DE

SUMA IMPORTANCIA QUE SIGA LAS

INSTRUCCIONES CADA VEZ QUE

UTILIZA EL CARGADOR.

b. Para reducir el riesgo de explosión de

una batería, siga estas instrucciones y

aquellas publicadas por el fabricante

de la batería y por el fabricante de

cualquier equipo que intente utilizar

en la proximidad de la batería. Revise

las pautas de precaución en estos

productos y en el motor.

2. PRECAUCIONES DE SEGURIDAD PERSONAL

2.1 Considere la idea de que alguna persona

se encuentre cerca suyo para poder

ayudarlo cuando trabaje en forma

cercana a una batería de plomo-ácido.

2.2 Cuente con una gran cantidad de agua

potable y jabón a mano en caso de que el

ácido de la batería tenga contacto con su

piel, ropa u ojos.

2.3 Utilice protección visual y corporal

completa, incluyendo gafas de seguridad

y prendas de protección. Evite tocar sus

ojos mientras trabaje en forma cercana a

la batería.

2.4 Si el ácido de la batería tiene contacto con

su piel o su ropa, lave de inmediato el área

afectada con agua y jabón. En caso de que

ingrese ácido en un ojo, sumerja el mismo

de inmediato bajo agua potable corriente

por al menos 10 minutos y obtenga

atención médica en forma inmediata.

2.5 NUNCA fume o permita la presencia de

chispas o llamas en la proximidad de una

batería o motor.

2.6 Tenga especial cuidado para reducir el

riesgo de dejar caer una herramienta

de metal sobre la batería. Esto podría

provocar chispas o un cortocircuito en la

batería o en cualquier otra pieza eléctrica

que podría provocar una explosión.

2.7 No utilice elementos personales de

metal tales como anillos, pulseras,

collares y relojes al trabajar con una

batería de plomo-ácido. Una batería

de plomo-ácido puede producir

• 19 •

una corriente de cortocircuito lo

sucientemente elevada como para

soldar un anillo o provocar efectos

similares sobre el metal, causando una

quemadura de gravedad.

2.8 Utilice este cargador solamente para

cargar baterías recargables de PLOMO-

ÁCIDO (estándar, AGM o GEL) con

recomienda usar capacidad de la batería

de 24Ah (6V) y 44-75Ah (12V). Este

cargador no está destinado a suministrar

energía a sistemas eléctricos de baja

tensión más que en una aplicación de

un motor de arranque. No utilice este

cargador de batería para cargar baterías

de pila seca que por lo general se utilizan

con artefactos domésticos. Estas baterías

podrían explotar y provocar lesiones a

personas o daño a la propiedad.

2.9 NUNCA cargue una batería congelada.

3. PREPARACIÓN PARA LA CARGA

3.1 Si resulta necesario extraer la batería

del vehículo para cargarla, siempre retire

el terminal con descarga a tierra en

primer lugar. Asegúrese de que todos los

accesorios en el vehículo se encuentren

apagados para evitar la formación de

arcos eléctricos.

3.2 Asegúrese de que el área que rodea a

la batería se encuentre bien ventilada

mientras se carga la batería.

3.3 Limpie los terminales de la batería antes

de cargar la batería. Durante la limpieza,

evite que la corrosión producida por aire

tenga contacto con sus ojos.

3.4 Agregue agua destilada a cada pila hasta

que el ácido de la batería alcance el

nivel especicado por el fabricante de la

batería. No provoque derrames. En lo que

concierne a baterías que no cuentan con

tapas extraíbles para pilas, tales como

baterías de plomo-ácido reguladas por

válvulas (VRLA, por sus siglas en inglés),

siga cuidadosamente las instrucciones de

recarga del fabricante.

3.5 Lea, comprenda y siga todas las

instrucciones para el cargador, la batería,

el vehículo y cualquier equipo que se

utilice cerca de la batería y el cargador.

Controle todas las precauciones

especícas establecidas por el fabricante

de la batería al realizar la carga, así

también como los índices de carga

recomendados.

3.6 Determine la tensión de la batería al

consultar el manual del usuario del

vehículo y asegúrese de que el interruptor

de selección de la tensión de salida

se encuentre establecido en la tensión

correcta (en su caso). Si el cargador

posee un índice de carga ajustable,

cargue la batería en el menor índice en

primer lugar.

4. UBICACIÓN DEL CARGADOR

4.1 Ubique el cargador a la mayor distancia

posible de la batería como lo permitan los

cables de CC.

4.2 Nunca ubique el cargador directamente

por encima de la batería que se carga; los

gases de la batería corroerán y dañarán

el cargador.

4.3 Nunca permita que el ácido de la batería

gotee sobre el cargador al leer el peso

especíco del electrolito o al cargar la

batería.

4.4 No utilice el cargador en un área cerrada o

restrinja la ventilación en cualquier forma.

4.5 No ubique la batería encima del cargador.

5. PRECAUCIONES DE CONEXIÓN EN CC

5.1 Conecte y desconecte las pinzas de

salida CC. sólo después de haber

establecido todos los interruptores del

cargador a la posición de “apagado” (si

es aplicable) y de haber desconectado

el enchufe de C.A. del tomacorriente

eléctrico. Nunca permita que las pinzas

tengan contacto entre sí.

5.2 Sujete las pinzas a la batería y al chasis,

como se indica en en las secciones 6 y 7.

• 20 •

6. SIGA ESTOS PASOS CUANDO LA BATERÍA ESTÉ COLOCADA EN EL VEHÍCULO

ADVERTENCIA:

UNA CHISPA PROVOCADA CERCA

DE LA BATERÍA PUEDE CAUSAR LA

EXPLOSIÓN DE LA BATERÍA. PARA

REDUCIR EL RIESGO DE PROVOCAR

CHISPAS CERCA DE LA BATERÍA:

6.1 Ubique los cables de CA y CC

adecuadamente para reducir el riesgo

de daños por la cubierta, la puerta y las

piezas móviles o calientes del motor.

6.2 Manténgase alejado de las paletas del

ventilador, correas, poleas y otras piezas

que podrían provocar lesiones.

6.3 Verique la polaridad de los bornes de

la batería. El borne POSITIVO (POS,

P, +) de la batería generalmente posee

un diámetro mayor al borne NEGATIVO

(NEG, N, -).

6.4 Determine qué borne de la batería

hace descarga a tierra (se encuentra

conectado) con el chasis. Si el borne

negativo hace descarga a tierra con el

chasis (como en la mayor parte de los

vehículos), ver el paso (6.5). Si el borne

positivo hace descarga a tierra con el

chasis, ver el paso (6.6).

6.5 En un vehículo con descarga a tierra

por borne negativo, conecte el gancho

POSITIVO (ROJO) del cargador de

batería al borne POSITIVO (POS, P, +) sin

descarga a tierra de la batería. Conecte

el gancho NEGATIVO (NEGRO) al chasis

del vehículo o al bloque motor alejado

de la batería. No conecte el gancho al

carburador, líneas de combustible o

cuerpos metálicos. Conecte a una pieza

metálica de calibre grueso del marco o

del bloque motor.

6.6 En un vehículo con descarga a tierra

por borne positivo, conecte el gancho

NEGATIVO (NEGRO) del cargador de

batería al borne NEGATIVO (NEG, N, -)

sin descarga a tierra de la batería.

Conecte el gancho POSITIVO (ROJO)

al chasis del vehículo o al bloque motor

alejado de la batería. No conecte al

carburador, líneas de combustible o

cuerpos metálicos. Conecte a una pieza

metálica de calibre grueso del marco o

del bloque motor.

6.7 Al desconectar el cargador, apague todos

los interruptores (en su caso), desconecte

el cable de C.A., retire el gancho del

chasis del vehículo y luego retire el gancho

del terminal perteneciente a la batería.

6.8 Vea Instrucciones de Operación para

duración de la carga.

7. SIGA ESTOS PASOS CUANDO LA BATERÍA SE ENCUENTRE FUERA DEL VEHÍCULO

ADVERTENCIA:

UNA CHISPA PROVOCADA CERCA

DE LA BATERÍA PUEDE CAUSAR LA

EXPLOSIÓN DE LA BATERÍA. PARA

REDUCIR EL RIESGO DE PROVOCAR

CHISPAS CERCA DE LA BATERÍA:

7.1 Verique la polaridad de los bornes de

la batería. El borne POSITIVO (POS,

P, +) de la batería generalmente posee

un diámetro mayor al borne NEGATIVO

(NEG, N, -).

7.2 Sujete al menos un cable aislado de

batería de 24 pulgadas (61 cm) de largo

con calibre 6 según el Calibre americano

de cables (AWG, por sus siglas en inglés)

al borne NEGATIVO (NEG, N, -) de la

batería.

7.3 Conecte el gancho POSITIVO (ROJO) del

cargador al borne POSITIVO (POS, P, +)

de la batería.

7.4 Ubíquese junto con el extremo libre del

cable que previamente sujetó al borne

NEGATIVO (NEG, N, -) de la batería a

la mayor distancia posible de la batería.

Luego conecte el gancho NEGATIVO

(NEGRO) del cargador al extremo libre

del cable.

7.5 No se ubique en posición frontal a la

batería al realizar la conexión nal.

7.6 Al desconectar el cargador, siempre

hágalo en forma inversa al procedimiento

de conexión y realice la primera conexión

tan lejos de la batería como sea posible.

7.7 Una batería marina (para barcos) se

debe retirar y cargar en tierra. Para

realizar una carga a bordo se necesitan

equipamientos especialmente diseñados

para uso marino.

La page charge ...

Schumacher DSR121DSR121 Le manuel du propriétaire

Marque: Schumacher

Modèle: DSR121DSR121

Catégorie: Chargeurs de batterie

Taper: Le manuel du propriétaire

Télécharger le PDF

rapport

dans d''autres langues

English: Schumacher DSR121DSR121 Owner's manual
español: Schumacher DSR121DSR121 El manual del propietario

Schumacher DSR121DSR121 Le manuel du propriétaire

Schumacher DSR121DSR121 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents