Hikoki C8FB2 Manuel utilisateur

Model Slide Compound Saw

Modèle Scie a coupe d’onglet radiale

Modelo Tronzadora radial abatible

C 8FB2

INSTRUCTION MANUAL AND SAFETY INSTRUCTIONS

WARNING

Improper and unsafe use of this power tool can result in death or serious bodily injury!

This manual contains important information about product safety. Please read and

understand this manual before operating the power tool. Please keep this manual

available for others before they use the power tool.

MODE D’EMPLOI ET INSTRUCTIONS DE SECURITE

AVERTISSEMENT

Une utilisation incorrecte et dangereuse de cet outil motorisé peut entraîner la mort

ou de sérieuses blessures corporelles!

Ce mode d’emploi contient d’importantes informations à propos de la sécurité de

ce produit. Prière de lire et d’assimiler ce mode d’emploi avant d’utiliser l’outil

motorisé. Garder ce mode d’emploi à la disponibilité des autres utilisateurs avant

qu’ils utilisent l’outil motorisé.

MANUAL DE INSTRUCCIONES E INSTRUCCIONES DE SEGURIDAD

ADVERTENCIA

¡La utilización inapropiada e insegura de esta herramienta eléctrica puede resultar

en lesiones serias o en la muerte!

Este manual contiene información importante sobre la seguridad del producto. Lea y

comprenda este manual antes de utilizar la herramienta eléctrica. Guarde este manual

para que puedan leerlo otras personas antes de que utilicen la herramienta eléctrica.

DOUBLE INSULATION

DOUBLE ISOLATION

AISLAMIENTO DOBLE

English

Page

IMPORTANT INFORMATION .....................................3

MEANINGS OF SIGNAL WORDS ...............................3

SAFETY

IMPORTANT SAFETY INSTRUCTIONS

FOR USING ALL POWER TOOLS ............................3

REPLACEMENT PARTS ...............................................6

USE PROPER EXTENSION CORD ...............................6

DOUBLE INSULATION FOR

SAFER OPERATION..................................................7

OPERATION AND MAINTENANCE

NAME OF PARTS..........................................................8

SPECIFICATIONS .........................................................9

ACCESSORIES ..............................................................9

STANDARD ACCESSORIES ....................................9

Page

OPTIONAL ACCESSORIES ....................................10

APPLICATIONS...........................................................10

PREPARATION BEFORE OPERATION .....................10

BEFORE USING ...........................................................11

BEFORE CUTTING ......................................................12

PRACTICAL APPLICATIONS.................................... 14

SAW BLADE MOUNTING

AND DISMOUNTING .............................................21

MAINTENANCE AND INSPECTION ........................22

SERVICE AND REPAIRS ............................................24

PARTS LIST .................................................................69

CONTENTS

Français

Page

INFORMATIONS IMPORTANTES ............................25

SIGNIFICATION DES MOTS D’AVERTISSEMENT

.....25

SECURITE

CONSIGNES DE SÉCURITÉ RELATIVES AUX

OUTILS ÉLECTRIQUES .......................................... 25

PIECES DE RECHANGE..............................................29

UTILISER LE CORDON DE RALLONGE

APPROPRIÉ ............................................................ 29

DOUBLE ISOLATION POUR UN

FONCTIONNEMENT PLUS SUR ...........................29

UTILISATION ET ENTRETIEN

NOM DES PIÈCES ......................................................30

SPÉCIFICATIONS ...................................................... 31

Page

ACCESSOIRES ............................................................31

ACCESSOIRES STANDARD ..................................31

ACCESSOIRES EN OPTION...................................32

APPLICATIONS...........................................................32

PRÉPARATION AVANT L’UTILISATION .................32

AVANT L’UTILISATION .............................................33

AVANT LA COUPE ......................................................34

APPLICATIONS PRATIQUES ....................................36

INSTALLATION ET RETRAIT DE LA LAME ............ 43

ENTRETIEN ET INSPECTION ....................................44

SERVICE APRÈS-VENTE ET RÉPARATIONS ..........46

TABLE DES MATIERES

Página

ACCESORIOS ..............................................................53

ACCESORIOS ESTÁNDAR.................................... 53

ACCESORIOS OPCIONALES .................................54

APLICACIONES...........................................................54

PREPARATIVOS PREVIOS A LA OPERACIÓN........54

ANTES DE LA UTILIZACIÓN .................................... 55

ANTES DEL CORTE.....................................................56

APLICACIONES PRÁCTICAS ....................................58

MONTAJE Y DESMONTAJE DE LA HOJA DE

SIERRA .....................................................................65

MANTENIMIENTO E INSPECCIÓN ........................ 66

SERVICIO Y REPARACIONES ...................................68

ÍNDICE

Español

Página

INFORMACIÓN IMPORTANTE .................................47

SIGNIFICADO DE LAS PALABRAS CLAVE ............ 47

SEGURIDAD

NORMAS DE SEGURIDAD PARA LAS

HERRAMIENTAS ELÉCTRICAS

...................................

47

PIEZAS DE REEMPLAZO .......................................... 51

UTILICE EL CABLE PROLONGADOR

ADECUADO ............................................................ 51

AISLAMIENTO DOBLE PARA OFRECER UNA

OPERACIÓN MÁS SEGURA ..................................51

OPERACIÓN Y MANTENIMIENTO

NOMENCLATURA DE PARTES.................................52

ESPECIFICACIONES...................................................53

3

English

IMPORTANT INFORMATION

Read and understand all of the operating instructions, safety precautions and warnings in the Manual before

operating or maintaining this power tool.

Most accidents that result from tool operation and maintenance are caused by the failure to observe basic

safety rules or precautions. An accident can often be avoided by recognizing a potentially hazardous situation

before it occurs and by observing appropriate safety procedures.

Basic safety precautions are outlined in the SAFETY section of this manual and in the sections which contain

the operation and maintenance instructions.

Hazards that must be avoided to prevent bodily injury or machine damage are identified by WARNINGS on

the tool and in this Manual.

Never use this tool in a manner that has not been specifically recommended by HITACHI, unless you first

confirm that the planned use will be safe for you and others.

MEANINGS OF SIGNAL WORDS

WARNING: indicates a potentially hazardous situation which, if ignored, could result in serious per-

sonal injury.

CAUTION: indicates a hazardous situation which, if ignored, could result in a moderate personal

injury, or could cause machine damage.

NOTE emphasizes essential information.

SAFETY

INPORTANT SAFETY INSTRUCTIONS FOR USING ALL POWER TOOLS

READ ALL OF THE WARNINGS AND OPERATING INSTRUCTIONS IN THIS MANUAL BE-

FORE OPERATING OR MAINTAINING THIS TOOL:

WARNING: When using this electric tool, take all necessary precautions to minimize the risk of elec-

tric shock or other personal injury.

In particular, always comply with the following safety rules:

1. ALWAYS KEEP GUARDS IN PLACE and in working order.

2. ALWAYS REMOVE ADJUSTING KEYS AND WRENCHES BEFORE STARTING TOOL.

Always confirm that all keys and adjusting wrenches have been removed from the tool before it is turned on.

3. ALWAYS KEEP WORK AREA CLEAN.

Avoid injuries by not cluttering the work areas and work

benches.

4. NEVER USE TOOL IN HAZARDOUS ENVIRONMENTS. Never use the power tool in damp or

wet places and never expose it to rain. Always keep the work area well lighted.

5. NEVER PERMIT CHILDREN OR OTHERS TO LOITER NEAR THE WORK AREA. Keep all

people (especially children) away from the work area. Always unplug unattended tools and keep the

work place tamper-proof by installing locks on the doors and on the master switches. Always remove

the lock-off button from the tool and store it in a secure place, when the tool is not in use.

6. NEVER FORCE THE TOOL. It will do the job better and more safely if it is operated at the rate for

which it was designed.

7. ALWAYS USE THE RIGHT TOOLS. Never force a tool or an attachment to do a job for which it

was not designed.

8. ALWAYS WEAR PROPER APPAREL WHEN WORKING WITH THE TOOL.

Never wear loose

clothing, gloves, neckties, rings, bracelets or other jewelry which may get caught in the moving parts.

Always wear non-slip footwear, preferably with steel toes. Wear protective hair covering to contain long

hair.

9. ALWAYS USE EYE PROTECTION WHEN WORKING WITH THE TOOL TO PREVENT

EYE INJURY. Ordinary eyeglasses do not provide adequate protection because the lenses are not

made of safety glass. Also, use a face mask for additional safety and wear a dust mask if the cutting

operation produces dust.

4

English

10. ALWAYS SECURE THE WORKPIECE TO THE FENCE OR THE TABLE.

Use clamps or a vise

to hold the workpiece in place. It is safer than using your hand and it frees both hands to operate the tool.

11. NEVER OVERREACH. Always keep proper footing and balance when working with the tool.

12. ALWAYS MAINTAIN TOOLS WITH CARE. Always keep tools sharp and clean for the best and

safest performance. Always follow instructions for lubricating the tool and for changing accessories.

13. ALWAYS DISCONNECT THE TOOL

before servicing and before changing blades or other accessories.

14. NEVER RISK UNINTENTIONAL STARTING WHEN PLUGGING IN THE TOOL. Always

confirm that the switch is in the OFF position before inserting the power plug into the receptacle.

15. ALWAYS USE RECOMMENDED ACCESSORIES ONLY WHEN OPERATING THIS TOOL.

Consult this instruction manual for descriptions of recommended accessories. To avoid personal injuries,

use only recommended accessories in conjunction with this tool.

16. NEVER STAND ON THE TOOL. Prevent serious injury by not tipping the tool and by not risking

unintentional contact with the saw blade.

17. ALWAYS CHECK FOR DAMAGED PARTS BEFORE USING THE TOOL. Always check the

guard and all other components for damage before using the tool to assure that they will function

properly. Check all moving parts for proper alignment, freedom from binding and other conditions that

might affect proper operation. Always repair or replace any damaged guards or other damaged

components before using the tool.

18. ALWAYS CONFIRM THE ROTATION DIRECTION OF THE BLADE BEFORE USING THE

TOOL. Always feed work into the tool against the rotation direction of the blade in order to prevent

possible injury.

19. NEVER LEAVE THE TOOL RUNNING WHILE UNATTENDED. TURN POWER OFF. Do not

leave tool until it comes to a complete stop. Always turn the power off when the tool is not in use.

Always unplug the power cord when the tool is not in use.

20. This tool was not designed to be used for mass-production applications and should not be used in

mass-production environments.

21. When servicing this tool, use only authorized replacement parts.

22. Apply 115 volts AC only to this tool. Applying the wrong voltage or applying DC power can cause the

POWER TOOL to operate improperly and cause serious personal injury or damage to the tool.

23. Never raise the saw blade from the workpiece until it has first come to a complete stop.

24. Always use outboard stands to provide support for long workpieces that overhang the table of the slide

compound saw.

25. Always return the carriage to the full rear position after each crosscut operation in order to reduce the

risk of injury.

26. POLARIZED PLUGS To reduce the risk of electric shock, this equipment has a polarized plug (one

blade is wider than the other). This plug will fit in a polarized outlet only one way. If the plug does not fit

fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install the

proper outlet. Do not change the plug in any way.

Specific Safety Rules for Use of this Power Tool

WARNING: The following specific operating instructions must be observed when using this POWER

TOOL in order to avoid injury:

DO’s

ALWAYS OBSERVE THE FOLLOWING RULES TO ASSURE SAFE USE OF THIS TOOL:

1. Review this Manual and familiarize yourself with the safety rules and operating instructions for this

POWER TOOL before attempting to use it.

2. Always confirm that the POWER TOOL is clean before using it.

3. Always wear snug-fitting clothing, non-skid footwear (preferably with steel toes) and eye protection

when operating the POWER TOOL.

4. Always handle the POWER TOOL carefully. If the POWER TOOL falls or strikes against a hard object, it

might become deformed or cracked or sustain other damage.

5. Always cease operating the saw at once, if you notice any abnormality whatsoever.

5

English

6. Always confirm that all components are mounted properly and securely before using the tool.

7. When replacing the saw blade, always confirm that the rpm rating of the new blade is correct for use

on this tool.

8. Always shut off the power and wait for the saw blade to completely stop rotating before doing any

maintenance or adjustments.

9. During slide cutting, always push the saw blade away from the operator.

10. Always clamp or otherwise secure the workpiece to the fence; otherwise the workpiece might be thrust

form the table and cause bodily harm.

11. During miter or bevel cutting, always wait for the rotation of the blade to stop completely before lifting

the saw blade.

12. Always make a trial run first before attempting any new use of the saw.

13. Always handle the saw blade with care when dismounting and mounting it.

14. Always confirm that the workpiece is free of nails or other foreign objects before beginning a cut.

15. Always keep your hands out of the path of the saw blade.

16. Always confirm that the safety cover is in the proper place before using the saw.

17. Always confirm that the safety cover does not obstruct the sliding motion of the saw before attempting

slide cutting.

18. Inspect the tool power cords periodically.

19. Always confirm that the proper lengths and types of extension cords are being utilized, if necessary,

before starting the tool.

20. Always confirm that the motor air vents are fully open before using the tool.

21. Always wait until the motor has reached full speed before starting a cut.

22. Always keep the handles dry, clean and free of oil and grease. Hold the tool firmly when in use.

23. Always use outboard stands to provide support for long workpieces that overhang the table of the

slide compound saw.

24. Always operate the tool after ensuring the workpiece is fixed properly with a vise assembly.

25. Always use slide fence (A) and slide fence (B) if a workpiece is too small to be fixed with fence (A) and

fence (B) of the base.

26. The operating instructions provided with the tool shall direct the user to secure the tool to supporting

structure if, during normal operation, there is a tendency for the tool to tip over, slide, or walk on the

supporting surface.

DON’Ts

NEVER VIOLATE THE FOLLOWING RULES TO ASSURE SAFE USE OF THIS TOOL:

1. Never operate the POWER TOOL unless you fully understand the operating instructions contained in

this Manual.

2. Never leave the POWER TOOL unattended without first unplugging the power cord.

3. Never operate the POWER TOOL when you are tired, after you have taken any medications, or have

consumed any alcoholic beverages.

4. Never use the POWER TOOL for applications not specified in the instruction manual.

5. Never operate the tool while wearing loose clothing, a necktie or jewelry, or while your hair is uncovered,

to protect against getting caught in the moving machinery.

6. Never reach around the saw blade.

7. Never touch any moving parts, including the blade, while the saw is in use.

8. Never remove any safety devices or blade guards; use of the tool without them would be hazardous.

9. Never lock the safety cover; always confirm that it slides smoothly before using the tool.

10. Never damage the power cord of the tool.

11. Never attempt to move a plugged-in POWER TOOL while your finger is on the starting switch.

12. Never use the POWER TOOL if the starting switch does not turn on and off properly.

6

English

13. Never use the POWER TOOL if the plastic housing or the handle is cracked or deformed.

14. Never use the POWER TOOL near flammable liquids or gases because sparking can cause an explo-

sion.

15. Never clean plastic components with solvents because the plastic may dissolve.

16. Never operate the saw unless all the blade guards are in place.

17. Never raise the saw blade from the workpiece until it has first come to a complete stop.

18. When slide cutting, never pull the handle toward the operator, since this could cause the saw blade to

kick up from the workpiece. Always push the handle away from the operator in a single, smooth motion.

19. Never place your limbs inside of the line next to warning sign “ ” while the tool is being operated.

This may cause hazardous conditions.

20. Never use abrasive type blades on this saw.

21. Never expose to rain or use in damp locations.

22. Never cut ferrous metals or masonry.

WARNING

FOR YOUR OWN SAFETY READ THIS INSTRUCTION MANUAL BEFORE OPERATING THE

SLIDE COMPOUND SAW

1. Always wear eye protection when using the slide compound saw.

2. Always keep hands out of the path of the saw blade.

3. Never operate the saw without the guards in place.

4. Never perform any freehand operation with the slide compound saw.

5. Never reach around the saw blade.

6. Always turn off tool and wait for saw blade to stop before moving workpiece or changing settings.

7. Always disconnect power before changing blade or servicing.

8. Saw blade diameter is 8-1/2" (216mm).

9. No load speed is 4900rpm.

10. To reduce the risk of injury, return carriage to the full rear position after each crosscut operation.

REPLACEMENT PARTS

When servicing use only identical replacement parts.

Repairs should be conducted only by a Hitachi authorized service center.

USE PROPER EXTENSION CORD

Make sure your extension cord is in good condition. When using an extension cord, be sure to use one

heavy enough to carry the current your product will draw. An undersized cord will cause a drop in line

voltage resulting in loss of power and overheating. Table shows the correct size to use depending on cord

length and nameplate ampere rating. If in doubt, use the next heavier gage. The smaller the gage number,

the heavier the cord.

MINIMUM GAGE FOR CORD SETS

Total Length of Cord in Feet (Meter)

0 – 25 26 – 50 51 – 100 101 – 150

(0 – 7.6) (7.9 – 15.2) (15.5 – 30.5) (30.8 – 45.7)

Ampere Rating AWG

More Not More

Than Than

0 – 6 18 16 16 14

6 – 10 18 16 14 12

10 – 12 16 16 14 12

12 – 16 14 12 Not Recommended

7

English

WARNING: Avoid electrical shock hazard. Never use this tool with a damaged or frayed electrical cord

or extension cord.

Inspect all electrical cords regularly. Never use in or near water or in any environment

where electric shock is possible.

DOUBLE INSULATION FOR SAFER OPERATION

To ensure safer operation of this power tool, HITACHI has adopted a double insulation design. “Double

insulation” means that two physically separated insulation systems have been used to insulate the electrically

conductive materials connected to the power supply from the outer frame handled by the operator. Therefore,

either the symbol “ ” or the words and “Double insulation” appear on the power tool or on the nameplate.

Although this system has no external grounding, you must still follow the normal electrical safety precautions

given in this Instruction Manual, including not using the power tool in wet environments.

To keep the double insulation system effective, follow these precautions:

* Only HITACHI AUTHORIZED SERVICE CENTER should disassemble or assemble this power tool, and only

genuine HITACHI replacement parts should be installed.

* Clean the exterior of the power tool only with a soft cloth moistened with soapy water and dry thoroughly.

* Never use solvents, gasoline or thinners on plastic components; otherwise the plastic may dissolve.

SAVE THESE INSTRUCTIONS

AND

MAKE THEM AVAILABLE TO

OTHER USERS OF THIS TOOL!

8

English

OPERATION AND MAINTENANCE

NOTE: The information contained in this Instruction Manual is designed to assist you in the safe opera-

tion and maintenance of the power tool. Some illustrations in this Instruction Manual may show

details or attachments that differ from those on your own power tool.

NAME OF PARTS

Fig. 1

Fig. 2

Trigger Switch

8mm Depth Adjustment Bolt

Slide Pipe (B)

Slide Pipe (A)

Clamp Lever

Indicator

6mm Knob Bolt

(Optional Accessory)

Locking Pin

Nameplate

Spindle Lock

Fence (A)

Slide Fence (A)

Stopper

(Optional Accessory)

Table Insert

Turntable

Indicator

Saw Cover

Slide Fence (B)

10mm Knob Bolt

Fence (B)

Screw Holder

Vise Assembly

Holder

(Optional Accessory)

Gear Case

Base

Side Handle

Dust Bag

Knob

Holder (A)

Hinge

Handle

Spindle Cover

Bolt

Washer (C)

Sub Cover

Safety Cover

Guard

Head

9

English

e Slide Fence Assembly

For how to use, refer to

page 15.

t 10mm BOX wrench

(1 piece)

q 8" (216mm) TCT Saw

blade (1 piece)

w Dust bag (1 piece)

For how to use, refer to

page 21.

r Vise Assembly w/knob

bolt (1 piece)

For how to use, refer to page

15.

(No. of teeth 24 Code No.

998840)

SPECIFICATIONS

Item Model C 8FB2

Motor Type Series commutator motor

Power source Single-phase AC 60Hz

Voltage (Volts) 115

Full-load current (Amp) 9.5

Applicable Outside Dia. 8-1/2" (216mm)

saw blade Hole Dia. 5/8" (15.9mm)

No load speed 4900rpm

Max.

Bevel 0

°

Miter 0

°

Max. Height 2-9/16" (65mm) Max. Height 2-15/16" (75mm)

sawing Max. Width 12" (305mm)

(

Max. Width 11" (280mm)

)

dimension *11-21/32" (296mm) *10-21/32" (271mm)

Miter 45

°

Max. Height 2-9/16" (65mm), Width 8-21/32" (220mm)

*8-5/16" (211mm)

Bevel 45

°

Miter 0

°

Max. Height 1-25/32" (45mm), Width 12" (305mm)

*11-21/32" (296mm)

Miter 45

°

Max. Height 1-25/32" (45mm), Width 8-21/32" (220mm)

*8-5/16" (211mm)

Miter sawing range Left 0° – 45° Right 0° – 57° (Bevel 45°; Left and Right 0° – 45°)

Bevel sawing range Left 0° – 45°

Net weight 38.6lbs. (17.5kg)

Cord 2 Conductor type cable 8ft. (2.5m)

*When slide fence assembly is used.

ACCESSORIES

WARNING: Accessories for this power tool are mentioned in this Instruction Manual.

The use of any other attachment or accessory can be dangerous and could cause injury or

mechanical damage.

STANDARD ACCESSORIES

Fig. 3

(C330274)

10

English

OPTIONAL ACCESSORIES...sold separately

q Extension Holder and Stopper (Fig. 1) (Code No. 998866)

w Guard Assembly (A) (Adjustable) (Code No. 998984)

e Saw blade 8-1/2" (216mm) TCT Saw blade (Total teeth: 36) (Code No. 998860)

r Saw blade 8-1/2" (216mm) TCT Saw blade (Total teeth:60) (Code No.998862)

t Saw blade 8-1/2" (216mm) TCT Saw Blade for aluminum (Total teeth: 60) (Code No.998864)

NOTE: Accessories are subject to change without any obligation on the part of the HITACHI.

APPLICATIONS

Wood and aluminum sash.

PREPARATION BEFORE OPERATION

Make the following preparations before operating the power tool:

1. Installation

Fig. 4

Attach the power tool to a level, horizontal work bench in accordance with Fig. 4.

Select 5/16" (8mm) diameter bolts suitable in length for the thickness of the work bench.

Bolt length should be at least 1" (25mm) plus the thickness of the work bench.

For example, use 2" (50mm) or larger bolts for a 1" (25mm) thick work bench.

The holder attached to the rear of the base helps stabilize the power tool.

Base holder adjustment:

Loosen the 6mm bolt with the supplied 10mm box wrench.

Adjust the base holder until its bottom surface contacts the work

bench surface.

After adjustment, firmly tighten the 6mm bolt.

Fig. 5

11/32" (9mm)

3 Holes

11-13/16" (300mm)

5-29/32" (150mm)

10-13/32" (264mm)

1" (25mm) thick bench

Work Bench

5/16" (8mm) Nut

5/16" (8mm) BoltBase

Adjust the base holder until

its bottom surface contacts

the work bench surface.

Move

6mm Bolt

Base Holder

11

English

2. Releasing the locking pin

Fig. 6-a Fig. 6-b

When the power tool is prepared for shipping, its main parts are secured by a locking pin.

Move the handle (see Fig. 1) slightly so that the locking pin can be disengaged and adjusted as indicated

in Fig. 6-b.

NOTE: Lowering the handle (see Fig. 1) slightly will enable you to disengage the locking pin more

easily and safely.

The lock position of the locking pin is for carrying and storage only.

3. Installing the dust bag, holder, stopper and vises.

(The holder and stopper are optional accessories).

Attach the dust bag, holder, stopper and vise assembly, slide fence (A) and slide fence (B) as indicated in Fig. 1.

BEFORE USING

1. Make sure the power source is appropriate for the tool.

WARNING: Never connect the power tool unless the available AC power source is of the same

voltage as that specified on the nameplate of the tool.

Never connect this power tool to a DC power source.

2. Make sure the trigger switch is turned OFF.

WARNING: If the power cord is connected to the power source with the trigger switch turned

ON the power tool will start suddenly and can cause a serious accident.

3. Check the saw blade for visible defects.

Confirm that the saw blade is free of cracks or other visible damage.

4. Confirm that the saw blade is attached securely to the power tool.

Using the supplied 10mm box wrench, tighten the bolt on the saw blade spindle to secure the saw blade.

For details, see Fig. 37-a and Fig. 37-b in the section on “SAW BLADE MOUNTING AND DISMOUNTING”.

5. Check the safety cover for proper operation.

Safety cover is designed to protect the operator from coming into

contact with the saw blade during operation of the tool.

Always check that the safety cover moves smoothly and covers

the saw blade properly.

Fig. 7

WARNING: NEVER OPERATE THE POWER TOOL if the safety cover does not function smoothly.

During transport, fit the pin into the

deep slot.

NOTE: This position is not be used

for any cutting operation.

Locking Pin

During operation fit

the pin stoppers into

the shallow slot.

Pull out to disengage.

Rotate the knob 1/4 turn

and fit the pin stoppers

into the shallow slot.

Clockwise

Locking Pin

Safety Cover

Sub Cover

12

English

6mm

Machine Screw

Saw Blade

Workpiece

Table insert

Workpiece

6mm

Machine Screw

Saw Blade

Table insert

Guard

Workpiece

Fence (A)

Vise

Assembly

Fence (B)

6. Confirm the position of the spindle lock before using the tool.

After installing the saw blade, confirm that the spindle lock has been returned to the retract position

before using the power tool (see Fig. 2).

7. Check the lower limit position of the Saw Blade.

Although it was adjusted before shipment, carefully check the height of the saw blade. Confirm that the

saw blade can be lowered 15/32" to 1/2" (12mm to 13mm) below the table insert. For details, see the

section on “Checking the saw blade lower limit position”.

8. Check the Power Receptacle.

To prevent overheating, accidental stopping or intermittent operation, confirm that the power cord

plug fits properly in the electrical receptacle and does not fall out after it is inserted. Repair or replace

the receptacle if it is faulty.

9. Confirm the tool’s power cord is not damaged.

Repair or replace the power cord if an inspection indicates that it is damaged.

AFTER CONNECTING THE POWER PLUG TO AN APPROPRIATE AC POWER SOURCE,

CHECK THE OPERATION OF THE TOOL AS FOLLOWS:

10. Trial Run

After confirming that no one is standing behind, the power tool start and confirm that no operating

abnormalities exist before attempting a cutting operation.

11. Inspect the rotating stability of the saw blade.

For precise cutting, rotate the saw blade and check for deflection to confirm that the blade is not noticeably

unstable; otherwise vibrations might occur and cause an accident.

BEFORE CUTTING

1. Cutting a groove on the guard

Holder (A) has a guard (see Fig. 8) into which a groove must be cut.

After placing a suitable wooden piece to sit on the fence and the

table surfaces, fix it with the vise assembly.

After the switch has been turned on and the saw blade has reached

maximum speed, slowly lower the handle to cut a groove on the

guard.

CAUTION: Do not cut the groove too quickly; otherwise the

guard might become damaged.

Fig. 8

2. Positioning the table insert

[Right angle cutting] [Left bevel angle cutting]

Fig. 9-a Fig. 9-b

13

English

Adjust the table insert on the turntable until it is correctly aligned to the saw blade, as indicated below.

Table insert adjustment:

(1) Loosen the three 6mm machine screws securing the right side table insert.

(2) Check that the table insert is positioned fully to the right, and temporarily tighten the back and front

6mm machine screws.

(3) Secure a piece of wood (about 7-7/8" (200mm) wide) to the turntable with the vise assembly.

(4) Cut the piece of wood at the desired angle.

(5) Align the right side table insert with the cutting line as indicated in Figs. 9-a and 9-b.

(6) Securely tighten the back and front 6mm machine screws.

(7) Remove the workpiece, and securely tighten the center 6mm machine screws.

If the power tool is properly adjusted, cutting can be made accurate by aligning a premarked ink line

with the table insert.

When the power tool is shipped from the factory, the right side table insert is put in a position where

it will not contact the saw blade at a full 45° bevel cut.

Therefore, before operation, adjust the right side table insert to the desired cutting angle.

3. Checking the saw blade lower limit position

Check that the saw blade can be lowered 15/32" to 1/2" (12mm to

13mm) below the table insert.

If necessary, adjust as follows:

(1) Loosen the 8mm wing nut and the two 8mm nuts on the 8mm

depth adjustment bolt.

(2) Turn the 8mm depth adjustment bolt as necessary to set the

lower limit position.

(3) Once the adjustment is complete, fully tighten the two 8mm

nuts and the 8mm wing nut.

NOTE: Before tightening the two 8mm nuts and the 8mm wing

nut, confirm that the saw blade is adjusted so that it will

not cut into the turntable.

Fig. 10

4. Oblique angle

Before the power tool is shipped from the factory, it is adjusted for

0° and left 45° bevel cutting angles.

The positioning and bevel cutting angle can be adjusted by

loosening the 8mm nylock bolt and by changing the height of the

8mm nylock bolt.

(Maximum bevel cutting angle is 45°).

Fig. 11

5. Securing the workpiece

WARNING: Always clamp or vise to secure the workpiece to the fence; otherwise the workpiece

might be thrust from the table and cause bodily harm.

8mm Nut

(2 pieces)

8mm Depth Adjustment Bolt

8mm Wing Nut

Table

Insert

Turntable

8mm Nylock

Bolt

14

English

6. Installing the holders ... (Optional accessory)

The holders help keep longer workpieces stable and in place dur-

ing the cutting operation.

(1) As indicated in Fig. 12, use a steel square for aligning the upper

edge of the holders with the base surface.

(2) After aligning, secure the holders with the 6mm knob bolts (Op-

tional accessory).

Fig. 12

7. Stopper for precision cutting ... (Stopper is optional accessory)

The stopper facilitates continuous precision cutting in lengths of

10-7/16" to 16-15/16" (265mm to 430mm).

To install the stopper, attach it to the holder with the 6mm knob

bolt as shown in Fig. 13.

Fig. 13

8. Using an ink line

Press down the handle to lift the safety cover as shown in Fig. 14,

and align the premarked ink line with the saw blade.

Fig. 14

CAUTION: Never lift the safety cover while the saw blade is rotating.

PRACTICAL APPLICATIONS

WARNING: * To avoid personal injury, never remove or place a workpiece on the table while the tool

is being operated.

* Never place your limbs inside of the line next to warning sign while the tool is being

operated. This may cause hazardous conditions (see Fig. 15).

Fig. 15

Line

Warning Sign

Marking

(pre-marked)

Fence (B)

Workpiece

Holder

Move

6mm Knob Bolt

Base Surface

Stopper

6mm

Knob Bolt

(Optional

Accessory)

Holder

Steel Square

Handle

Safety Cover

15

English

Fence (B)

Slide Fence (B)

Workpiece

2-5/32" (55mm)2-4/3" (70mm)

Fence (A)

Slide Fence (A)

Cut off side piece

Fig. 18

Handle

Lock-off Button

Hole

Trigger Switch

Knob

Vise Plate

Workpiece

10mm Knob Bolt

Fence

Vise Shaft

Screw Holder

Clearance between fence (A) and fence (B) and the workpiece

is necessary. The edge of workpiece should not overlap with

fence (A) and fence (B).

1. Switch operation

The trigger switch lock-off button is designed to prevent inadvert-

ent operation of the power tool. To operate the power tool, it is nec-

essary to first fully insert the lock-off button into the hole on the

handle as shown in Fig. 16.

The trigger switch will not operate unless the lock-off button has

been pushed in.

When the trigger switch is released, the power goes off and the

lock-off button automatically returns to its initial position, locking

the trigger switch.

Fig. 16

WARNING: Always remove the lock-off button from the handle when the power tool is not in

use. This will ensure that the power tool cannot be turned on accidentally or by

someone (especially a child) who is not qualified to use the power tool. If the lock-off

button is left in the handle, serious personal injury can result. Since the lock-off button

fits rather tightly, it may be necessary to turn it to the left and right during mounting

and removing.

2. Using the Vise Assembly (Standard accessory)

(1) The vise assembly can be mounted on either the left fence

{Fence (B)} or the right fence {Fence (A)} by loosening the 10mm

knob bolt.

(2) The screw holder can be raised or lowered according to the

height of the workpiece by loosening the 6mm knob bolt. After

the adjustment, firmly tighten the 6mm knob bolt and fix the

screw holder.

(3) Turn the upper knob and securely fix the workpiece in position

(Fig. 17).

CAUTION: Always confirm that the motor head (see Fig. 1) does not contact the vise assembly

when it is lowered for cutting. If there is any danger that it may do so, loosen the

10mm knob bolt slightly and move the vise to a position where it will not contact the

saw blade.

Also, always confirm that the vise assembly is mounted on the right side {Fence (A)}

before using the saw for compound cutting operations (miter + bevel cutting).

3. Using the Slide Fence (A) and Slide Fence (B) (Standard accessory)

Slide fence (A) and slide fence (B) are meant to stabilize small

workpieces as shown in Fig. 18.

6mm

Knob Bolt

Fig. 17

16

English

Fig. 19

(1) Set slide fence (A) and slide fence (B) on fence (A) and fence (B) of the base.

(2) To attach use the four machine screws with nylon washers and flange nuts as shown in Fig. 19.

(3) Adjust slide fence (A) and slide fence (B) to stabilize the workpiece. Adjustable range of slide fence

(A) and slide fence (B) is from 0 to 3-3/4" (0 to 95mm)).

(4) Confirm the position of slide fence (A) and slide fence (B) on fence (A) and fence (B) with four

machine screws tightly so slide fence (A) and slide fence (B) do not move (see Fig. 19).

CAUTION: * Before operation, ensure that the saw blade does not contact slide fence (A) and

slide fence (B). In case the saw blade contacts slide fence (A) and slide fence (B),

adjust the position of slide fence (A) and slide fence (B) again.

* Maximum cross-cutting width (Bevel 0°, Miter 0°) is 11-21/32" (296mm).

4. Cutting Operation

(1) As shown in Fig. 20 the width of the saw blade is the

width of the cut. Therefore, slide the workpiece to the

right (viewed from the operator’s position) when length

b is desired, or to the left when length a is desired.

(2) Once the saw blade reaches maximum speed, push

the handle down carefully until the saw blade

approaches the workpiece.

(3) Once the saw blade contacts the workpiece, push the

handle down gradually to cut into the workpiece.

(4) After cutting the workpiece to the desired depth, turn

the power tool OFF and let the saw blade stop

completely before raising the handle from the

workpiece to return it to the full retract position.

CAUTION: * Increased pressure on the handle will not increase the cutting speed.

On the contrary, too much pressure may result in overload of the motor and/or

decreased cutting efficiency.

WARNING: * Confirm that the trigger switch is turned OFF and the power plug has been removed

from the receptacle whenever the tool is not in use.

* Always remove the lock-off button from the handle and store it in a secure place

after completing the work.

Flange Nut

Fence (B)

Slide Fence (B)

Nylon Washer

Machine Screw

Flange Nut

Fence (A)

Slide Fence (A)

Nylon Washer

Machine Screw

Adjusting Line

Marking

(pre-marked)

Marking

(pre-marked)

(Front View)

ab

a

b

a

b

Fig. 20

17

English

5. Cutting narrow workpieces (Press cutting)

Slide the hinge down to holder (A), then tighten the slide securing

knob as indicated in Fig. 21.

Lower the handle to cut the workpiece.

Using the power tool this way will permit cutting of workpieces of

up to 2-9/16" (65mm) square.

Fig. 21

6. Cutting wide workpieces (Slide cutting)

(1) Workpieces up to 2-9/16" (65mm) high and 12" (305mm) wide:

Loosen the slide securing knob, grip the handle and slide the

saw blade forward.

Then press down on the handle and slide the saw blade back to

cut the workpiece as indicated in Fig. 22. This facilitates cutting

of workpieces of up to 2-9/16" (65mm) in height and 12" (305mm)

in width.

(2) Workpieces up to 2-15/16" (75mm) high and 11" (280mm) wide:

Workpieces of up to 2-15/16" (75mm) in height and up to 11"

(280mm) in width can be cut in the same manner as described

in paragraph 6-(1) above.

Fig. 22

CAUTION: * If the handle is pressed down with excessive or lateral force, the saw blade may

vibrate during the cutting operation and cause unwanted cutting marks on the

workpiece, thus reducing the quality of the cut.

Accordingly, press the handle down gently and carefully.

* In slide cutting, gently push the handle back (rearwards) in a single, smooth opera-

tion.

Stopping the handle movement during the cut will cause unwanted cutting marks

on the workpiece.

WARNING: * For slide cutting, follow the procedures indicated above in Fig. 22.

Forward slide cutting (toward the operator) is very dangerous because the saw

blade could kick upward from the workpiece. Therefore, always slide the handle

away from the operator.

* Always return the carriage to the full rear position after each crosscut operation in

order to reduce the risk of injury.

* Never put your hand on the side handle during the cutting operation because the

saw blade comes close to the side handle when the motor head is lowered.

Press

Down

Workpiece

Holder (A)

Hinge

Slide Securing Knob

Handle

w Pess

Down

Workpiece

q Pull Forward

e Push Rearward to Cut

18

English

Angle Scale

Grade Scale

a

Miter Scale

Fig. 25

Fig. 24

Bevel Angle

Scale

Loosen

Clamp Lever

Tighten

Indicator

Fig. 26

Tighten

Loosen

Side Handle

Miter

Scale

Indicator

Turn the

turntable

7. Bevel cutting procedures

(1) Loosen the clamp lever and bevel the saw blade to the left.

(2) Adjust the bevel angle to the desired setting while watching

the bevel angle scale and indicator, then secure the clamp le-

ver.

(3) Follow the procedures indicated in paragraphs 5 and 6 above.

For maximum dimensions for bevel cutting of up to 1-25/32"

(45mm) in height and 12" (305mm) width.

Fig. 23

WARNING: When the workpiece is secured on the left side of the blade, the short cut-off portion

will come to rest on the right side of the saw blade. Always turn the power off and let

the saw blade stop completely before raising the handle from the workpiece.

If the handle is raised while the saw blade is still rotating, the cut-off piece may

become jammed against the saw blade causing fragments to scatter about danger-

ously.

When stopping the bevel cutting operation halfway, start cutting after pulling back

the motor head to the initial position.

Starting from halfway, without pulling back, causes the safety cover to be caught in

the cutting groove of the workpiece and to contact the saw blade.

8. Miter cutting procedures

(1) Loosen the side handle and adjust the turntable until the indi-

cator aligns with the desired setting on the miter scale (Fig. 26).

(2) Re-tighten the side handle to secure the turntable in the de-

sired position.

(3) The miter scale (Fig. 24) indicates both the cutting angle on the

angle scale and the gradient on the grade scale.

(4) The gradient, which is the ratio of the height to the base of the

triangular section to be removed, may be used for setting the

miter scale instead of the cutting angle, if desired (see Fig. 25).

(5) Therefore, to cut a workpiece at a grade of 2/10, set the indicator

to position a as indicated in Fig. 24.

NOTE: * Positive stops are provided at the right and left of

the 0° center setting, at 15°, 22.5°, 31.6°, 35.3° and

45° settings.

Check that the miter scale and the tip of the indica-

tor are properly aligned.

* Operation of the saw with the miter scale and indi-

cator out of alignment, or with the side handle not

properly tightened, will result in poor cutting preci-

sion.

19

English

9. Compound cutting procedures

Compound cutting can be performed by following the instructions in 7 and 8 above. At a bevel angle of

45° and a miter angle of 45°, a workpiece of 1-25/32" (45mm) in height and up to 8-21/32" (220mm) in

width can be cut.

CAUTION: Always secure the workpiece with the right hand side for compound cutting. Never

rotate the turntable to the right for compound cutting, because the saw blade might

then contact the clamp or vise that secures the workpiece, and cause personal injury

or damage.

10. Crown molding cutting procedures

Fig. 27 shows two common crown molding types having angles of (θ) 38° and 45°.

For the typical crown molding fittings, see Fig. 28.

Fig. 27 Fig. 28

The table below shows the miter angle and the bevel angle settings that are ideal for the two crown

molding types.

NOTE: For convenience, positive stops are provided for both the miter setting (left and right 31.6°,

35.3°) and the bevel setting positions (left 30°, 33.9°).

For miter cut setting

If the turntable has been set to either of the angles described, move the turntable adjusting side handle

a little to the right and left to stabilize the position and to properly align the miter angle scale and the tip

of the indicator before the operation starts.

For bevel cut setting

Move handle on bevel section to the left and check that the position is stable and that the bevel angle

scale and the tip of the indicator are properly aligned. Then tighten the clamp lever.

(1) Setting to cut crown moldings at positions q and r in Fig. 28 (see Fig. 29):

q Turn the turntable to the right and set the Miter Angle as follows:

* For 45°type crown moldings: 35.3° ( mark)

* For 38°type crown moldings: 31.6° ( mark)

w Tilt the head to the left and set the Bevel Angle as follows:

* For 45°type crown moldings: 30° ( mark)

* For 38°type crown moldings: 33.9° ( mark)

e

Position the crown molding so that the upper surface (A in Fig. 27) contacts the fence as indicated in

Fig. 30.

Wall

A upper surface

Ceiling

B lower surface

Ceiling

Wall

q

w

er

To process crown molding

at

positions 1 and 4 in Fig. 28.

To process crown molding at

positions 2 and 3 in Fig. 28.

Type of

Crown

Molding

45° Type

38° Type

Miter Angle

Setting

right 35.3°

( mark)

right 31.6°

( mark)

Miter Angle

Setting

left 35.3°

( mark)

left 31.6°

( mark)

Bevel Angle

Setting

left 30°

( mark)

left 33.9°

( mark)

Bevel Angle

Setting

30°

( mark)

33.9°

( mark)

20

English

(2) Setting to cut crown moldings at positions w and e in Fig. 28 (see Fig. 31):

q Turn the turntable to the left and set the Miter Angle as follows:

* For 45°type crown moldings: 35.3° ( mark)

* For 38°type crown moldings: 31.6° ( mark)

w Tilt the head to the left and set the Bevel Angle as follows:

* For 45°type crown moldings: 30° ( mark)

* For 38°type crown moldings: 33.9° (

mark)

e Position the crown molding so that the lower surface (B in Fig. 27) contacts the fence as in Fig. 32.

Fig. 29 Fig. 31

Fig. 30 Fig. 32

11. Groove cutting procedures

Fig. 33 Fig. 34

Grooves in the workpiece can be cut as indicated in Fig. 33 by adjusting the 8mm depth adjustment bolt.

Cutting depth adjustment procedure:

(1) Loosen the 8mm wing nut and turn the 8mm depth adjustment bolt by hand.

(2) Adjust to the desired cutting depth by setting the distance between the saw blade and the surface of

the base (see b in Fig. 33).

(3) The 8mm wing nut must be properly tightened after the adjustment has been completed.

NOTE: When cutting a single groove at either end of the workpiece, remove the unneeded portion

with a chisel.

Fence

Table on Base

B

Table on Base

Fence

A

B

A

q

Bevel

Angle Scale

r

Fence

Base

Miter Angle Scale

Turntable

Bevel

Angle Scale

e

Base

Miter Angle Scale

Fence

w

Turntable

Head

Bottom Line of

the Groove

Turntable

a

b

Cut grooves with saw blade

8mm

Wing Nut

8mm

Depth Adjustment Bolt

La page charge ...

Hikoki C8FB2 Manuel utilisateur

Ce manuel convient également à

Hikoki C8FB2 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents