Paxar FreshMarx System Monarch 9416 Manuel utilisateur

®

Monarch

9416 Printer

Custom Kit

®

User

Manual

User

Manual

Each product and program carries a respective written warranty, the only

warranty on which the customer can rely. Paxar reserves the right to make

changes in the product, the programs, and their availability at any time and

without notice. Although Paxar has made every effort to provide complete and

accurate information in this manual, Paxar shall not be liable for any omissions

or inaccuracies. Any update will be incorporated in a later edition of this

manual.

be reproduced, transmitted, stored in a retrieval system, or translated into any

language in any form by any means, without the prior written permission of

Paxar Americas, Inc.

WARNING

This equipment has been tested and found to comply with the limits for a

Class A digital device, pursuant to Part 15 of the FCC Rules. These

limits are designed to provide reasonable protection against harmful

interference when the equipment is operated in a commercial

environment. This equipment generates, uses, and can radiate radio

frequency energy and, if not installed and used in accordance with the

instruction manual, may cause harmful interference to radio

communications. Operation of this equipment in a residential area is

likely to cause harmful interference in which case the user will be

required to correct the interference at his own expense.

CANADIAN D.O.C. WARNING

This digital apparatus does not exceed the Class A limits for radio noise

emissions from digital apparatus set out in the Radio Interference

Regulations of the Canadian Department of Communications.

Le présent appareil numérique n'émet pas de bruits radioélectriques

dépassant les limites applicables aux appareils numériques de la classe

A prescrites dans le Réglement sur le brouillage radioélectrique édicte

par le ministère des Communications du Canada.

Trademarks

MONARCH® and 9416® are registered trademarks of Paxar Americas, Inc.

Paxar® is a trademark of Paxar Corporation.

Paxar Americas, Inc.

170 Monarch Lane

Miamisburg, Ohio 45342

i

TABLE OF CONTENTS

INTRODUCTION ...........................................................................................1-1

Overview ................................................................................................1-1

Unpacking the Kit Components .................................................................1-2

Connecting the Cable...............................................................................1-2

Using the Keyboard .................................................................................1-3

Control Keys........................................................................................1-4

SETTING UP THE PRINTER ..........................................................................2-1

Setting the Supply Type ...........................................................................2-2

Setting the Feed Mode .............................................................................2-3

Setting the Ribbon...................................................................................2-4

Sending the Configuration ........................................................................2-5

PRINTING LABELS.......................................................................................3-1

Format 1.................................................................................................3-2

Format 2.................................................................................................3-2

Format 3.................................................................................................3-3

Format 4.................................................................................................3-4

Format 5.................................................................................................3-5

Using the About Menu..............................................................................3-6

TROUBLESHOOTING....................................................................................4-1

ii

Introduction 1-1

INTRODUCTION

This User Manual contains information about using the KU008

Keyboard with your Monarch 9416 printer. For information about

supply loading or care and maintenance, refer to the printer’s Equipment

Manual on our Web site (www.paxar.com).

Note: Information in this document supercedes information in previous

versions. Refer to our Web site for any updates.

This manual includes information about

♦ unpacking the components.

♦ connecting the cables.

♦ using the keyboard.

♦ setting up the printer.

♦ printing labels.

Overview

The keyboard may contain five preset formats.

♦ Format 1 (1.2” width x 1.1” length)

♦ Format 2 (1.2” width x 1.1” length)

♦ Format 3 (1.2” width x 1.1” length)

♦ Format 4 (1.5” width x 2.7” length)

♦ Format 5 (1.5” width x 2.7” length)

1

1-2 User Manual

Unpacking the Kit Components

After you unpack the kit, you should have the keyboard (part number

126364), the printer with a power supply, power cord, and external supply

holder (part number 126894). Look through all packaging material for

parts. Keep the box and packaging material in case an item ever needs

repair.

Connecting the Cable

1. Turn off the printer. Press the switch on the back of the printer to the

OFF position (O).

2. Connect the keyboard’s serial cable to the printer.

3. Plug the round end of the power supply cable into the printer.

4. Turn on the printer. The keyboard receives power from the printer.

Introduction 1-3

Using the Keyboard

The keyboard has full alphabetic keys with numeric keys, function keys,

four arrow keys, and several special keys.

1-4 User Manual

Control Keys Description

Exit

Returns the display to the next higher

menu.

Enter

Selects the displayed menu item or

accepts entered data.

Form

Displays the list of available formats.

 or 

Right Arrow

Down Arrow

Displays the next menu item.

 or 

Left Arrow

Up Arrow

Displays the previous menu item.

Backspace

Moves the cursor one space to the

left. Located next to the spacebar.

Clear

Clears all entered data.

Alt F1

Displays the communication setup

menu.

Setting up the printer 2-1

SETTING UP THE PRINTER

This chapter describes how to

♦ set the supply type

♦ set the feed mode

♦ set the ribbon

♦ save the configuration.

Main Menu

Option Choices Default

Supply Type Black Mark/Die Cut Black Mark

Feed Mode No Peel/Peel No Peel

Ribbon No Ribbon/Ribbon No Ribbon

When you turn on the printer, the keyboard briefly displays

PAXAR 9416CT KIT

Then, you see

FORMAT 1

1. Press  or  until you see

PRINTER SETUP

2

Format 1-5

Printer

Setup

Supply

T

y

pe

Feed

Mode

Ribbon

Send CFG

to Printer

Return to

Main Menu

A

bout

2-2 User Manual

2. Press Enter. You see

PRINTER MENU

SUPPLY TYPE

3. Press  or  to move through the Printer Setup menu.

Setting the Supply Type

The printer has a black mark/die cut sensor, which it uses to properly

calibrate supplies. Black mark supply has sense marks (black marks) on

the back of them. Die cut supply does not have any black marks.

1. From the Printer Setup menu, press  or  until you see

SUPPLY TYPE

2. Press Enter. You see

PRINTER SUPPLY MENU

BLACK MARK BM

3. Press  or  to select the supply type you are using, then press

Enter. The current setting is displayed on the right. The default is

Black Mark.

4. Press  or  until you see

RETURN TO PRINTER MENU

5. Press Enter.

Setting up the printer 2-3

Setting the Feed Mode

There are two feed modes: peel and no peel (continuous). Peel mode

separates the backing paper from the label. No peel (continuous) mode

prints labels in a continuous strip.

1. From the Printer Setup menu, press  or  until you see

FEED MODE

2. Press Enter. You see

SUPPLY FEED MODE

NO PEEL NPL

3. Press  or  to select the mode you need, then press Enter. The

current setting is displayed on the right. The default is No Peel.

4. Press  or  until you see

RETURN TO PRINTER MENU

5. Press Enter.

2-4 User Manual

Setting the Ribbon

Thermal direct supplies do not require a ribbon. Thermal Transfer

supplies do require a ribbon.

1. From the Printer Setup menu, press  or  until you see

RIBBON

2. Press Enter. You see

RIBBON MENU

NO RIBBON NRB

3. Press  or  to select the option you need, then press Enter. The

current setting is displayed on the right. The default is No Ribbon.

4. Press  or  until you see

RETURN TO PRINTER MENU

5. Press Enter.

Setting up the printer 2-5

Sending the Configuration

When you change the printer’s configuration, you must send the new

settings to the printer or it uses the default settings of Black Mark, No

Peel, and No Ribbon.

1. From the Printer Setup menu, press  or  until you see

SEND CFG TO PRINTER

2. Press Enter. The new configuration settings appear.

For example:

PRINTER CONFIGURATION

BM NPL NRB SEND Y/N?

Where BM is Black Mark, NPL is No Peel, and NRB is No Ribbon.

3. Select Yes to send the new configuration to the printer.

Select No to return to the default settings.

4. Press Enter.

5. When you are done, select Return to Main Menu and press Enter.

2-6 User Manual

Printing Labels 3-1

PRINTING LABELS

This chapter describes printer setup and the data entry procedures

for each format.

Note: If you make a mistake entering data, press

to backspace one character, or press Clear to

erase all entered data.

To start printing formats:

When you turn on the printer, the keyboard briefly displays

PAXAR 9416CT KIT

Then, you see

FORMAT 1

1. Press  or  to select the format you need.

2. Press Enter.

3. See the following Format descriptions to enter the data.

Note: You may need to press Form to see the list of available formats.

3

3-2 User Manual

Format 1

1. Load 1.2” width x 1.1” length supply.

2. Enter the data as prompted:

Prompt What You Do

LINE 1

Enter up to ten characters. Press Enter.

LINE 2

Enter up to ten characters. Press Enter.

LINE 3

Enter up to ten characters. Press Enter.

LINE 4

Enter up to ten characters. Press Enter.

PRINT QTY

Enter up to three numeric digits. Press Enter.

Format 2

1. Load 1.2” width x 1.1” length supply.

2. Enter the data as prompted:

Prompt What You Do

UPCA Barcode

Enter up to 12 numeric digits. Press Enter.

PRINT QTY

Enter up to three numeric digits. Press Enter.

UPCA Barcode

Line 1

Line 2

Line 3

Line 4

Printing Labels 3-3

Format 3

1. Load 1.2” width x 1.1” length supply.

2. Enter the data as prompted:

Prompt What You Do

LINE 1

Enter up to 12 characters. Press Enter.

UPCA Barcode

Enter up to 12 numeric digits. Press Enter.

LINE 2

Enter up to 12 characters. Press Enter.

PRINT QTY

Enter up to three numeric digits. Press Enter.

UPCA Barcode

Line 1

Line 2

3-4 User Manual

Format 4

1. Load 1.5” width x 2.7” length supply.

2. Enter the data as prompted:

Prompt What You Do

LINE 1

Enter up to 15 characters. Press Enter.

LINE 2

Enter up to 15 characters. Press Enter.

LINE 3

Enter up to 15 characters. Press Enter.

LINE 4

Enter up to 15 characters. Press Enter.

UPC BARCODE

Enter up to 12 numeric digits. Press Enter.

LINE 5

Enter up to 15 characters. Press Enter.

PRINT QTY

Enter up to three numeric digits. Press Enter.

Note: The price field is already formatted with the dollar sign and

decimal point. To enter a price of $19.45, press the 1 9 4 and 5

keys.

UPC Barcode

Line 1

Line 2

Line 4

Line 3

Line 5

Printing Labels 3-5

Format 5

1. Load 1.5” width x 2.7” length supply.

2. Enter the data as prompted:

Prompt What You Do

LINE 1

Enter up to 15 characters. Press Enter.

LINE 2

Enter up to 15 characters. Press Enter.

LINE 3

Enter up to 15 characters. Press Enter.

LINE 4

Enter up to 15 characters. Press Enter.

LINE 5

Enter up to 15 characters. Press Enter.

LINE 6

Enter up to 15 characters. Press Enter.

PRINT QTY

Enter up to three numeric digits. Press Enter.

Note: The price field is already formatted with the dollar sign and

decimal point. To enter a price of $19.45, press the 1 9 4 and 5

keys.

Line 1

Line 2

Line 4

Line 3

Line 5

Line 6

3-6 User Manual

Using the About Menu

To display version or copyright information, press Form. Press  or 

until you see “About.” Press Enter.

You can also display version or copyright information by pressing Exit

when you see the first prompt in any format.

La page est en cours de chargement...

Paxar FreshMarx System Monarch 9416 Manuel utilisateur

Ce manuel convient également à

Paxar FreshMarx System Monarch 9416 Manuel utilisateur

dans d''autres langues

Autres documents