User Guide
DTP T/R DP 4K 330
DTP T/R DP 4K 230
DTP Systems
DisplayPort Twisted Pair Extenders
68-2709-02 Rev. B
01 19
Safety Instructions
Safety Instructions • English
WARNING: This symbol, ,when used on the product, is
intended to alert the user of the presence of uninsulated dangerous
voltage within the product’s enclosure that may present a risk of electric
shock.
ATTENTION: This symbol, , when used on the product, is intended
to alert the user of important operating and maintenance (servicing)
instructions in the literature provided with the equipment.
For information on safety guidelines, regulatory compliances, EMI/EMF
compatibility, accessibility, and related topics, see the Extron Safety and
Regulatory Compliance Guide, part number 68-290-01, on the Extron
website, www.extron.com.
Sicherheitsanweisungen • Deutsch
WARNUNG: Dieses Symbol auf dem Produkt soll den Benutzer
darauf aufmerksam machen, dass im Inneren des Gehäuses dieses
Produktes gefährliche Spannungen herrschen, die nicht isoliert sind und
die einen elektrischen Schlag verursachen können.
VORSICHT: Dieses Symbol auf dem Produkt soll dem Benutzer in
der im Lieferumfang enthaltenen Dokumentation besonders wichtige
Hinweise zur Bedienung und Wartung (Instandhaltung) geben.
Weitere Informationen über die Sicherheitsrichtlinien, Produkthandhabung,
EMI/EMF-Kompatibilität, Zugänglichkeit und verwandte Themen finden Sie in
den Extron-Richtlinien für Sicherheit und Handhabung (Artikelnummer
68-290-01) auf der Extron-Website, www.extron.com.
Instrucciones de seguridad • Español
ADVERTENCIA: Este símbolo, , cuando se utiliza en el producto,
avisa al usuario de la presencia de voltaje peligroso sin aislar dentro del
producto, lo que puede representar un riesgo de descarga eléctrica.
ATENCIÓN: Este símbolo, , cuando se utiliza en el producto, avisa
al usuario de la presencia de importantes instrucciones de uso y
mantenimiento recogidas en la documentación proporcionada con el
equipo.
Para obtener información sobre directrices de seguridad, cumplimiento
de normativas, compatibilidad electromagnética, accesibilidad y temas
relacionados, consulte la Guía de cumplimiento de normativas y seguridad
de Extron, referencia 68-290-01, en el sitio Web de Extron, www.extron.com.
Instructions de sécurité • Français
AVERTISSEMENT : Ce pictogramme, , lorsqu’il est utilisé sur le
produit, signale à l’utilisateur la présence à l’intérieur du boîtier du
produit d’une tension électrique dangereuse susceptible de provoquer
un choc électrique.
ATTENTION : Ce pictogramme, , lorsqu’il est utilisé sur le produit,
signale à l’utilisateur des instructions d’utilisation ou de maintenance
importantes qui se trouvent dans la documentation fournie avec le
matériel.
Pour en savoir plus sur les règles de sécurité, la conformité à la
réglementation, la compatibilité EMI/EMF, l’accessibilité, et autres sujets
connexes, lisez les informations de sécurité et de conformité Extron, réf.
68-290-01, sur le site Extron, www.extron.com.
Istruzioni di sicurezza • Italiano
AVVERTENZA: Il simbolo, , se usato sul prodotto, serve ad
avvertire l’utente della presenza di tensione non isolata pericolosa
all’interno del contenitore del prodotto che può costituire un rischio di
scosse elettriche.
ATTENTZIONE: Il simbolo, , se usato sul prodotto, serve ad
avvertire l’utente della presenza di importanti istruzioni di funzionamento
e manutenzione nella documentazione fornita con l’apparecchio.
Per informazioni su parametri di sicurezza, conformità alle normative,
compatibilità EMI/EMF, accessibilità e argomenti simili, fare riferimento
alla Guida alla conformità normativa e di sicurezza di Extron, cod. articolo
68-290-01, sul sito web di Extron, www.extron.com.
Instrukcje bezpieczeństwa • Polska
OSTRZEŻENIE: Ten symbol, , gdy używany na produkt, ma na celu
poinformować użytkownika o obecności izolowanego i niebezpiecznego
napięcia wewnątrz obudowy produktu, który może stanowić zagrożenie
porażenia prądem elektrycznym.
UWAGI: Ten symbol, , gdy używany na produkt, jest przeznaczony do
ostrzegania użytkownika ważne operacyjne oraz instrukcje konserwacji
(obsługi) w literaturze, wyposażone w sprzęt.
Informacji na temat wytycznych w sprawie bezpieczeństwa, regulacji
wzajemnej zgodności, zgodność EMI/EMF, dostępności i Tematy pokrewne,
zobacz Extron bezpieczeństwa i regulacyjnego zgodności przewodnik, część
numer 68-290-01, na stronie internetowej Extron, www.extron.com.
Инструкция по технике безопасности • Русский
ПРЕДУПРЕЖДЕНИЕ: Данный символ, , если указан
на продукте, предупреждает пользователя о наличии
неизолированного опасного напряжения внутри корпуса
продукта, которое может привести к поражению электрическим
током.
ВНИМАНИЕ: Данный символ, , если указан на продукте,
предупреждает пользователя о наличии важных инструкций
по эксплуатации и обслуживанию в руководстве,
прилагаемом к данному оборудованию.
Для получения информации о правилах техники безопасности,
соблюдении нормативных требований, электромагнитной
совместимости (ЭМП/ЭДС), возможности доступа и других
вопросах см. руководство по безопасности и соблюдению
нормативных требований Extron на сайте Extron: ,
www.extron.com, номер по каталогу - 68-290-01.
安全说明 • 简体中文
警告： 产品上的这个标志意在警告用户该产品机壳内有暴露的危险 电压，
有触电危险。
注意： 产品上的这个标志意在提示用户设备随附的用户手册中有
重要的操作和维护(维修）说明。
关于我们产品的安全指南、遵循的规范、EMI/EMF 的兼容性、无障碍
使用的特性等相关内容，敬请访问 Extron 网站 , www.extron.com，参见
Extron 安全规范指南，产品编号 68-290-01
。
安全記事 • 繁體中文
警告: 若產品上使用此符號，是為了提醒使用者，產品機殼內存在著
可能會導致觸電之風險的未絕緣危險電壓。
注意 若產品上使用此符號，是為了提醒使用者，設備隨附的用戶手冊中有
重要的操作和維護（維修）説明。
有關安全性指導方針、法規遵守、EMI/EMF 相容性、存取範圍和相關主題的詳細資
訊，請瀏覽 Extron 網站：www.extron.com，然後參閱《Extron 安全性與法規
遵守手冊》，準則編號 68-290-01。
安全上のご注意
• 日本語
警告: この記号 が製品上に表示されている場合は、筐体内に絶縁されて
いない高電圧が流れ、感電の危険があることを示しています。
注意:この記号 が製品上に表示されている場合は、本機の取扱説明書に
記載されている重要な操作と保守(整備)の指示についてユーザーの注意
を喚起するものです。
安全上のご注意、法規厳守、EMI/EMF適合性、その他の関連項目に
つ い て は 、エ ク スト ロ ン の ウェ ブ サ イト www.extron.com よ り 『 Extron Safety
and Regulatory Compliance Guide』 ( P/N 68-290-01) をご覧ください。
안전 지침 • 한국어
경고: 이 기호 가 제품에 사용될 경우, 제품의 인클로저 내에 있는
접지되지 않은 위험한 전류로 인해 사용자가 감전될 위험이 있음을
경고합니다.
주의: 이 기호 가 제품에 사용될 경우, 장비와 함께 제공된 책자에 나와
있는 주요 운영 및 유지보수(정비) 지침을 경고합
니다.
안전 가이드라인, 규제 준수, EMI/EMF 호환성, 접근성, 그리고 관련 항목에
대한 자세한 내용은 Extron 웹 사이트(www.extron.com)의 Extron 안전 및
규제 준수 안내서, 68-290-01 조항을 참조하십시오.
Copyright
© 2014-2019 Extron Electronics. All rights reserved. www.extron.com
Trademarks
All trademarks mentioned in this guide are the properties of their respective owners.
The following registered trademarks (
®
), registered service marks (
SM
), and trademarks (
TM
) are the property of RGBSystems, Inc. or
ExtronElectronics (see the current list of trademarks on the Terms of Use page at www.extron.com):
Registered Trademarks
(
®
)
Extron, Cable Cubby, ControlScript, CrossPoint, DTP, eBUS, EDID Manager, EDID Minder, Flat Field, FlexOS, Glitch Free. Global Configurator,
GlobalScripter, GlobalViewer, Hideaway, HyperLane, IPIntercom, IPLink, KeyMinder, LinkLicense, LockIt, MediaLink, MediaPort,
NetPA, PlenumVault, PoleVault, PowerCage, PURE3, Quantum, Show Me, SoundField, SpeedMount, SpeedSwitch, StudioStation,
SystemINTEGRATOR, TeamWork, TouchLink, V-Lock, VideoLounge, VN-Matrix, VoiceLift, WallVault, WindoWall, XTP, XTPSystems, and ZipClip
Registered Service Mark
(SM)
: S3 Service Support Solutions
Trademarks
(
™
)
AAP, AFL (Accu-RateFrameLock), ADSP(Advanced Digital Sync Processing), Auto-Image, CableCover, CDRS(ClassD Ripple Suppression),
Codec Connect, DDSP(Digital Display Sync Processing), DMI (DynamicMotionInterpolation), DriverConfigurator, DSPConfigurator,
DSVP(Digital Sync Validation Processing), eLink, EQIP, Everlast, FastBite, FOX, FOXBOX, IP Intercom HelpDesk, MAAP, MicroDigital,
Opti-Torque, PendantConnect, ProDSP, QS-FPC(QuickSwitch Front Panel Controller), RoomAgent, Scope-Trigger, ShareLink, SIS,
SimpleInstructionSet, Skew-Free, SpeedNav, Triple-Action Switching, True4K, Vector™ 4K , WebShare, XTRA, and ZipCaddy
FCC Class A Notice
This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to part15 of the FCC rules. The ClassA limits provide reasonable
protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and,
if not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is
likely to cause interference. This interference must be corrected at the expense of the user.
ATTENTION:
•
The T
wisted Pair Extension technology works with unshielded twisted pair (UTP)
or shielded twisted pair (STP) cables; but to ensure FCC Class A and CE
compliance, STP cables and STP Connectors are required.
•
La technologie extension pair
es torsadées fonctionne avec les câbles paires
torsadées blindées(UTP) ou non blindées(STP). Afin de s’assurer de la
compatibilité entre FCC ClasseA et CE, les câbles STP et les connecteurs STP
sont nécessaires.
NOTES:
•
This unit was tested with shielded I/O cables on the peripheral devices. Shielded
cables must be used to ensur
e compliance with FCC emissions limits.
•
For mor
e information on safety guidelines, regulatory compliances, EMI/EMF
compatibility, accessibility, and related topics, see the Extron Safety and
Regulatory Compliance Guide on the Extron website.
Conventions Used in this Guide
Notifications
The following notifications are used in this guide:
ATTENTION:
•
Risk of pr
operty damage.
•
Risque de dommages matériels.
NOTE: A note draws attention to important information.
Specifications Availability
Product specifications are available on the Extron website, www.extron.com.
Extron Glossary of Terms
A glossary of terms is available at http://www.extron.com/technology/glossary.
aspx.
DTP T/R DP 4K 330 and DTP T/R DP 4K 230 Twisted Pair Extenders • Introduction iv
vDTP T/R DP 4K 330 and DTP T/R DP 4K 230 Twisted Pair Extenders • Contents
Introduction ...................................................1
About this Guide ................................................. 1
About the DTP T/R DP 4K 330 and
DTP T/R DP 4K 230 Extenders .......................... 1
TP Cable Advantages ......................................... 1
Features ............................................................. 2
Installation and Operation ........................... 3
Rear Panel Connections and Features ................ 3
Transmitter Connections and Switch ............... 4
Receiver Connections ..................................... 6
Connector and Cable Details .......................... 7
Front Panel Connection and Power Indicator .... 11
Operation ......................................................... 11
Use and Compatibility with Other Extron DTP
Products ...................................................... 11
Remote Control ...........................................12
Simple Instruction Set Control .......................... 12
Host-to-Receiver Communications ............... 12
Receiver-Initiated Message ........................... 12
Error responses ............................................ 12
Timeout ........................................................ 12
Using the Command and Response Table .... 13
Product Configuration Software ........................ 14
Installing the Software ................................... 14
Starting the Program .................................... 17
Updating the Firmware ................................. 18
Equipment Mounting .................................. 22
Mounting the Transmitter or Receiver ................ 22
Tabletop Use ................................................ 22
Mounting kits ................................................ 22
UL Rack-Mounting Guidelines ...................... 22
Contents
DTP T/R DP 4K 330 and DTP T/R DP 4K 230 Twisted Pair Extenders • Contents vi
DTP T/R DP 4K 330 and DTP T/R DP 4K 230 Twisted Pair Extenders • Introduction 1
Introduction
• About this Guide
• About the DTP T/R DP 4K 330 and DTP T/R DP 4K 230 Extenders
• TP Cable Advantages
• Features
About this Guide
This guide describes the Extron DisplayPort Twisted Pair Extenders. This guide covers two
Extender models:
• DTP T/R DP 4K 330 — Consists of a DTP T DP 4K 330 transmitter and a
DTP R DP 4K 330 receiver.
• DTP T/R DP 4K 230 — Consists of a DTP T DP 4K 230 transmitter and a
DTP R DP 4K 230 receiver.
This guide describes how to install, operate, and configure the transmitters and receivers.
About the DTP T/R DP 4K 330 and DTP T/R DP 4K 230 Extenders
The Extron DTP T/R DP 4K transmitter and receiver pair (see figure 1 on the next page) are
twisted pair Extender sets for transmission of:
• HDCP-compliant DisplayPort video (which can include embedded digital audio)
• Optional analog audio
• RS-232 and IR control signals
NOTE: The RS-232 and IR communications are a passive pass-through only.
The transmitter and receiver do not generate or respond to the RS-232 and IR
communication signals.
Transmission is over one Extron XTP DTP 24 shielded twisted pair (STP) cable
(recommended) or Category (CAT) 5e or CAT 6 STP cable. The two models are similar
except for the transmission range:
• DTP T/R DP 4K 330 — Up to 330 feet (100 m)
• DTP T/R DP 4K 230 — Up to 230 feet (70 m)
TP Cable Advantages
Twisted pair cable is much smaller, lighter, more flexible, and less expensive than coaxial
or HDMI cable. These transmitter and receiver twisted pair (TP) products make cable runs
simpler and less cumbersome. Termination of the cable with RJ-45 connectors is simple,
quick, and economical.
NOTE: Do not use Extron UTP23SF-4 Enhanced Skew-Free AV UTP cable or STP201
cable to link the transmitter and receiver. The DTP DP transmitter and receiver do not
work properly with these cables.
DTP T/R DP 4K 330 and DTP T/R DP 4K 230 Twisted Pair Extenders • Introduction 2
HDMI IN
AUDIO IN
HDMI IN
AUDIO IN
100-240V ~ -- A MAX
1
CONFIGURABLE
HDMI HDMI
5
8
C
RS-232 IR
RS-232 IR
Tx Rx Tx RxG
Tx Rx Tx RxG
Tx Rx Tx RxG
HDMI
A
B
3
INPUTS OUTPUTS AUDIO INPUTS OUTPUTS REMOTE
2
6
7
4
Tx Rx
RS-232
G
LAN 1
LAN 2 LAN 3
2x25W(8Ω) / 2x50W(4Ω)
RESET
L 1 R
L
R
L 2
R
L
3
R
CLASS 2 WIRING
L 4
R
L 5
R
+48V
+48V
1 2
L R
VARIABLE
1
2
MIC/LINE
L 6
R
50/60 Hz
RS-232 IR
IN1608 IPCP SA
OVER DTP
OVER DTP
AMPLIFIED OUTPUT
G
Tx Rx
G
Tx Rx
G
Tx Rx
3 4 G
1 2RTSCTS
COM 1 COM 2 COM 3 DIGITAL I/O
1
S G
S G
2
IR/SERIAL RELAYS
1 2 C 3 4 C
PWR OUT = 6W
eBUS
+V+S -S G
R
SIG
DTP IN
LINK SIG
DTP IN
LINK SIG
DTP OUT
LINK
OVER TP
RS-232
IR
Tx Rx Tx RxG
POWER
12V
0.8A MAX
SIG LINK
IN
OUTPUTS
L R
AUDIO
AUDIO
INPUTS
OVER TP
RS-232
IR
Tx Rx Tx RxG
POWER
12V
0.8A MAX
SIG LINK
OUT
DTP
HDBT
PUSH PUSH
POWER GUIDE MENU RES 480 480p 720p 1080i 1080p
DIRECTV HD
SELECT
DIRECTV
1
Extron
Help
System
Off
Display
Room
Control
Off
Mute
Screen
Lighting
December 15, 2013 - 7:58 AM
Audio
Control
Volume
Mute
Tuner
1 2 3
VCRLaptop PC DVD
Doc
Cam
Tuner
On
Channel
Last
Presets
More
Presets
321
654
987
Enter
0
HDMI
DisplayPort
HDMI
HDMI HDMI
DisplayPort
RS-232
Blu-ray Player
Tuner
Media Player
PC
Display
CATx Cable
up to 230' (70 m)
CATx Cable
up to 330' (100 m)
CATx Cable
up to 230' (70 m)
Extron
DTP R DP 230
Receiver
Ethernet
Ethernet
Extron
TLP Pro 720T
7" Tabletop TouchLink
Pro Touchpanel
TCP/IP
Network
Laptop
Laptop
DisplayPort
Extron
DTP T DP 230
Transmitter
Extron
DTP T HWP 331 D
Transmitter
Extron
IN1608 IPCP SA
Scaling Presentation
Switcher
Figure 1. Typical DTP T/R DP 4K 230 Transmitter and Receiver Application in a
System with an IN1608
Features
Transmits DisplayPort video, control, and analog audio over a single STP cable
Standard twisted pair cables provide an economical, easily installed cable solution.
Long distance transmission — Extends video, audio, and control signals up to 330 feet
(100 meters) (DTP T/R DP 4K 330) or 230 feet (70 meters) (DTP T/R DP 4K 230).
The DTP transmitter is compatible with HDBaseT-enabled devices — The DTP
transmitter can be configured to send video and embedded audio, plus bidirectional RS-232
and IR signals to HDBaseT-enabled displays.
Supports Display Data Channel (DDC) transmission — The transmitter and receiver
pair fully supports long distance transmission of the DDC signals.
HDCP compliant
Control communications pass-through — Bidirectional RS-232 and IR control signals
can be transmitted alongside the digital video signal, so that the remote display can be
controlled without the need for additional cabling.
Supports computer video up to 2560x1600, HDTV 1080p/60 Deep Color, and 4K
resolutions
1-inch high, quarter rack width, metal enclosures — With low profile enclosures, the
transmitter and receiver can be discreetly installed in locations such as behind a plasma or
LCD flat-panel display.
External 100 VAC to 240 VAC, 50-60 Hz, international power supply — One power
supply is included with the transmitter.
Remote powering of transmitter or receiver — Only one power supply is normally
necessary to power both devices.
Compatible with all DTP HDMI 330 (230) and DTP DVI 330 (230) receivers, and
DTP 330- (230-)enabled products — The Extenders can be used with the Extron IN1608,
DTP CrossPoint 84, and other DTP 330- (230-)enabled products to meet application
requirements.
DTP T/R DP 4K 330 and DTP T/R DP 4K 230 Twisted Pair Extenders • Installation and Operation 3
Installation and
Operation
This section describes the installation and the operation of the DTP T/R DP 4K Extenders,
including:
• Rear Panel Connections and Features
• Front Panel Connection and Power Indicators
• Operation
NOTE: For equipment mounting, see Mounting the Transmitter or Receiver on
page 23.
Rear Panel Connections and Features
LR
POWER
12V
0.7A MAX
AUDIO
SIG LINK
DTP IN
OUTPUTS
AUDIO
INPUTS
OVER TP
RS-232
IR
Tx Rx Tx RxG
POWER
12V
0.8A MAX
SIG LINK
OUT
DTP
HDBT
DDDAAABBB EEE CCCFFF
Figure 2. DTP T DP 4K 330 and DTP T DP 4K 230 Rear Panel Connectors and
Switch
OVER TP
RS-232
IR
Tx Rx Tx RxG
POWER
12V
1.0A MAX
SIG LINK
DTP IN
OUTPUTS
LR
AUDIO
GGG IIIJJJKKK HHH
Figure 3. DTP R DP 4K 330 and DTP R DP 4K 230 Rear Panel Connectors
Transmitter Features Receiver Features
A
DisplayPort input port (see page 4)
G
DTP Input port (see page 6)
B
Audio input port (see page 4)
H
DisplayPort Output port (see page 6)
C
Over TP port (see page 4)
I
Audio Output port (see page 6)
D
TP function switch (see page 4)
J
Over TP port (see page 6)
E
TP Out port (see page 5)
K
Power connector and LED (see page 7)
F
Power connector and LED (see page 5)
DTP T/R DP 4K 330 and DTP T/R DP 4K 230 Twisted Pair Extenders • Installation and Operation 4
Transmitter Connections and Switch
A
DisplayPort input port (see figure 2 on the previous page) — Connect a
DISPLAYPORT
digital video input to this DisplayPort connector. The transmitters also accept
embedded digital audio on this port.
B
Audio input connector — If desired, plug an analog audio input into the
transmitter via this stereo mini jack connector.
NOTES:
•
The analog audio input on this connector is
not
embedded into the digital signal and is
in addition to the digital audio that may be
already embedded in the DisplayPort input.
•
See figur
e 4 to identify the connector tip, ring,
and sleeve when you are making connections
for the transmitter from existing audio cables.
A mono audio connector consists of the
tip and sleeve. A stereo audio connector
consists of the tip, ring, and sleeve.
Sleeve ( )
Ring (
-
)
Tip (+)
3.5 mm Stereo Plug Connector
(balanced)
Figure 4. TRS Connector
Wiring
C
Over TP RS-232 and IR connector — Connect a serial RS-232 signal,
OVER TP
RS-232
IR
Tx Rx Tx RxG
a modulated IR signal, or both to this 3.5 mm, 5-pole captive screw
connector for bidirectional RS-232 and IR communication
(see RS-232 and IR connector wiring on page 10 to wire the connector).
D
TP function switch — If the receiving device is in the Extron DTP series, set this
DTP
HDBT
switch to the DTP position. For an HDBaseT-enabled receiver type, set this switch
to the HDBT position. This switch tailors the output signal as follows:
HDBT position — The TP output consists of DisplayPort video with embedded digital
audio plus RS-232 and IR.
DTP position — The TP output consists of DisplayPort video with embedded digital
audio, analog audio, RS-232 and IR, and remote power.
ATTENTION:
•
Position this switch
BEFORE connecting the appropriate device to the TP
connector. Failure to comply can damage the endpoint.
•
Positionnez le sélecteur
AVANT de connecter l’appareil approprié au
connecteur TP. Ne pas respecter cette procédure pourrait endommager le
point de connexion.
NOTES:
• When the switch is in the HDBT position, the transmitter and receiver each
requires a local 12 VDC power supply.
• When the switch is in the DTP position, one 12 VDC power supply,
connected to either the transmitter or the receiver, can power both units.
DTP T/R DP 4K 330 and DTP T/R DP 4K 230 Twisted Pair Extenders • Installation and Operation 5
E
TP Output RJ-45 connector (see figure 2 on page 3) — Connect one end
SIG LINK
OUT
of a TP cable to this RJ-45 female connector on the transmitter. Ensure the
opposite end of this cable is connected to the receiver TP Input RJ-45
connector (see item
G
, below).
ATTENTION:
•
Do not connect these devices to a telecommunications or computer data
network.
•
Ne connectez pas ces appar
eils à des données informatiques ou à un réseau
de télécommunications.
NOTE: See TP cable termination and recommendations on page 7 to properly
wire the RJ-45 connectors and for detailed NOTES.
Signal LED — Indicates the unit is receiving a DisplayPort signal on the DisplayPort
input.
Link LED — Indicates a valid link is established between the units on the DTP input
and output cable.
F
Power connector — Plug the included external 12 VDC power supply into either this
2-pole connector or the power input connector on the receiver (see item
K
on page 7).
ATTENTION:
• Do not connect power to the DTP T/R DP 4K 330 or DTP T/R DP 4K 230 until
you have read the CAUTION and ATTENTION notices on pages 9 and 10.
•
Ne branchez pas l’alimentation au
DTP T/R DP 4K 330 ou DTP T/R DP 4K 230
avant d’avoir lu les deux rubriques « ATTENTION » aux pages 9 et 10.
NOTE: When the TP function switch (see item
D
on page 4) is in the DTP
position, one power supply can power both units.
When the TP function switch is in the HDBT position, the transmitter
and receiver each requires a local 12 VDC power supply.
Power LED —
Amber — The unit is receiving power remotely (on the DTP cable).
Green — The unit is receiving power locally.
DTP T/R DP 4K 330 and DTP T/R DP 4K 230 Twisted Pair Extenders • Installation and Operation 6
Receiver Connections
G
DTP Input RJ-45 connector (see figure 3 on page 3) — Connect one end
SIG LINK
DTP IN
of the TP cable from the transmitter output connector to this RJ-45 female
connector. Ensure the opposite end of this cable is connected to the
transmitter DTP Output RJ-45 connector (see item
E
, on the previous page).
ATTENTION:
•
Do not connect these devices to a telecommunications or computer data
network.
•
Ne connectez pas ces appar
eils à des données informatiques ou à un réseau
de télécommunications.
NOTE: See TP cable termination and recommendations on page 7 to properly
wire the RJ-45 connectors and for detailed NOTES.
Signal LED — Indicates the unit is receiving a valid signal on the DTP In connector.
Link LED — Indicates a valid link is established between the units on the DTP input
and output cable.
H
DisplayPort output connector — Connect a video display to this
DISPLAYPORT
DisplayPort connector.
I
Audio output connector — This 5-pole, 3.5 mm captive screw connector outputs
the transmitted, unamplified, line level analog audio. Connect an audio device, such as
an audio amplifier or powered speakers.
See figure 5 to properly wire a captive screw output connector. Use the supplied
tie-wrap to strap the audio cable to the extended tail of the connector.
Unbalanced Stereo Output Balanced Stereo Output
Do not tin the wires!
Tip
NO GROUND HERE
NO GROUND HERE
Tip
LR
Sleeves
Tip
Ring
Tip
Ring
LR
Figure 5. Captive Screw Connector Wiring for Stereo Audio Output
ATTENTION:
• For unbalanced audio, connect the sleeves to the ground contact.
DO NOT connect the sleeves to the negative (-) contacts.
•
Pour l’audio asymétrique, connectez les manchons au contact au sol.
Ne PAS connecter les manchons aux contacts négatifs (–).
NOTES:
• The length of exposed wires is important. The ideal length is 3/16 inch (5 mm).
• If the stripped section of wire is longer than 3/16 inch, the exposed wires
may touch, causing a short circuit.
•
If the stripped section of wir
e is shorter than 3/16 inch, wires can be easily
pulled out even if tightly fastened by the captive screws.
• Do not tin the power supply leads before installing them in the connector.
Tinned wires are not as secure in the connector and could be pulled out.
J
Over TP RS-232 and IR connector — Connect a serial RS-232 signal,
OVER TP
RS-232
IR
Tx Rx Tx RxG
a modulated IR signal, or both to this 3.5 mm, 5-pole captive screw
connector for bidirectional RS-232 and IR communication
(see RS-232 and IR connector wiring on page 10 to wire the connector).
DTP T/R DP 4K 330 and DTP T/R DP 4K 230 Twisted Pair Extenders • Installation and Operation 7
K
Power input connector (see figure 3 on page 3) — Plug the included external
12 VDC power supply into either this 2-pole connector or the power input connector on
the transmitter (see item
F
on the previous page).
ATTENTION:
•
Do not connect power to the
DTP T/R DP 4K 330 or DTP T/R DP 4K 230 until
you have read the CAUTION and ATTENTION notices on pages 9 and 10.
•
Ne branchez pas l’alimentation au
DTP T/R DP 4K 330 ou DTP T/R DP 4K 230
avant d’avoir lu les deux rubriques « ATTENTION » aux pages 9 et 10.
NOTE: When the TP function switch (see item
D
on page 4) is in the DTP
position, one power supply can power both units.
When the TP function switch is in the HDBT position
, the transmitter
and receiver each requires a local 12 VDC power supply.
Power LED —
Amber — The unit is receiving power remotely (on the DTP cable).
Green — The unit is receiving power locally.
Connector and Cable Details
TP cable termination and recommendations
Figure 6 details the TIA/EIA T568-B wiring standard. Use this standard to terminate TP
cables with RJ-45 connectors.
5
Pin
1
2
3
6
7
8
4
Side
12345678
Insert
Twisted
Pair Wires
Pins:
RJ-45
Connector
Wire color
White-green
Green
White-orange
White-b
lue
Orange
White-brown
Brown
Blue
TIA/EIA T
568B
Figure 6. TP Cable Termination
NOTE: Do not use Extron UTP23SF-4 Enhanced Skew-Free AV UTP cable or STP201
cable to link the transmitter and receiver. The DTP DisplayPort units do not work
properly with these cables.
Supported cables —
The DTP T/R DP 4K 330 and DTP T/R DP 4K 230 are compatible with shielded twisted pair
(STP) and unshielded twisted pair (U/UTP) cable. However, Extron strongly recommends
that you use STP cable to achieve best performance.
DTP T/R DP 4K 330 and DTP T/R DP 4K 230 Twisted Pair Extenders • Installation and Operation 8
Cable recommendations —
Extron recommends using the following practices to achieve full transmission distances up
to 330 feet (100 m) (DTP T/R DP 330) or 230 feet (70 m) (DTP T/R DP 230) and reduce
transmission errors.
• Use the following Extron XTP DTP 24 SF/UTP cables and DTP 24 connectors for the
best performance:
• XTP DTP 24/1000 Non-Plenum 1000' (305 m) spool 22-236-03
• XTP DTP 24P/1000 Plenum 1000' (305 m) spool 22-235-03
• XTP DTP 24 Plug Package of 10 101-005-02
• If not using XTP DTP 24 cable, at a minimum, Extron recommends 24 AWG, solid
conductor, STP cable with a minimum bandwidth of 400 MHz.
• Terminate cables with shielded connectors to the TIA/EIA T 568 B standard.
• Use no more than two pass-through points, which may include patch points, punch
down connectors, couplers, and power injectors. If these pass-through points are
required, use CAT 6 or 6a shielded couplers and punch down connectors.
NOTE: When using STP cable in bundles or conduits, consider the following:
• Do not exceed 40% fill capacity in conduits.
•
Do not comb the cable for the first 20 meters, wher
e cables are straightened,
aligned, and secured in tight bundles.
•
Loosely place cables and limit the use of tie wraps or V
elcro
®
.
• Separate twisted pair cables from AC power cables.
DTP T/R DP 4K 330 and DTP T/R DP 4K 230 Twisted Pair Extenders • Installation and Operation 9
Power supply wiring
NOTE: One power supply is included with the transmitter and normally can power
both units.
Figure 7 shows how to wire the connector. Use the supplied tie-wrap to strap the power
cord to the extended tail of the connector.
Power Supply
Output Cord
Captive Screw
Connector
SECTION A–A
Ridges
Smooth
AA
Tie Wrap
3
5
Figure 7. Power Connector Wiring
CAUTION:
ATTENTION :
•
The wir
es must be kept separate while the power supply is plugged in. Remove
power before wiring.
•
Les deux cor
dons d’alimentation doivent être tenus à l’écart l’un de l’autre quand
l’alimentation est branchée. Couper l’alimentation avant de faire l’installation
électrique.
• The length of exposed wires is important. The ideal length is 3/16 inch (5 mm).
• Any longer and the exposed wires may touch, causing a short circuit.
•
Any shorter and the wir
es can be easily pulled out even if tightly fastened by the
captive screws.
• La longueur des câbles exposés est importante. La longueur idéale est de 5mm
(3/16inches).
• S’ils sont un peu plus longs, les câbles exposés pourraient se toucher et
provoquer un court circuit.
• S’ils sont un peu plus courts, ils pourraient sortir, même s’ils sont attachés par
les vis captives.
• Do not tin the power supply leads before installing them in the connector. Tinned
wires are not as secure in the connector and could be pulled out.
• Ne pas étamer les conducteurs avant de les insérer dans le connecteur. Les câbles
étamés ne sont pas aussi bien fixés dans le connecteur et pourraient être retirés.
DTP T/R DP 4K 330 and DTP T/R DP 4K 230 Twisted Pair Extenders • Installation and Operation 10
ATTENTION:
•
This pr
oduct is intended to be supplied by a UL Listed power source marked
“Class 2” or “LPS,” rated 12 VDC, 1.0 A minimum. Always use a power supply
supplied by or specified by Extron. Use of an unauthorized power supply voids all
regulatory compliance certification and may cause damage to the supply and the
end product.
•
Ce pr
oduit est destiné à une utilisation avec une source d’alimentation listéeUL avec
l’appellation «Classe2» ou «LPS» et normée 12Vcc, 1,0A minimum. Utilisez
toujours une source d’alimentation fournie ou recommandée par Extron. L’utilisation
d’une source d’alimentation non autorisée annule toute conformité réglementaire et
peut endommager la source d’alimentation ainsi que le produit final.
•
Unless otherwise stated, the AC/DC adapters ar
e not suitable for use in air handling
spaces or in wall cavities.
• Sauf mention contraire, les adaptateurs AC/DC ne sont pas appropriés pour une
utilisation dans les espaces d’aération ou dans les cavités murales.
•
The installation must always be in accor
dance with the applicable provisions of
National Electrical Code ANSI/NFPA 70, article 725 and the Canadian Electrical
Code part 1, section 16. The power supply shall not be permanently fixed to a
building structure or similar structure.
• Cette installation doit toujours être en accord avec les mesures qui s’applique
au National Electrical Code ANSI/NFPA70, article725, et au Canadian Electrical
Code, partie1, section16. La source d’alimentation ne devra pas être fixée de
façon permanente à une structure de bâtiment ou à une structure similaire.
• Power supply voltage polarity is critical. Incorrect voltage polarity can damage the
power supply and the unit. The ridges on the side of the cord (see figure 7 on the
previous page) identify the power cord negative lead.
•
La polarité de la source d’alimentation est primordiale. Une polarité incorrecte
pourrait endommager la source d’alimentation et l’unité. Les stries sur le côté du
cordon (voir l’illustration 7 sur la page 9) permettent de repérer le pôle négatif du
cordon d’alimentation.
To verify the polarity before connection, plug in the power supply with no load and check the
output with a voltmeter.
RS-232 and IR connector wiring
Figure 8 shows how to wire the RS-232 connector.
TxRx
RxTx
Gnd
Gnd
IR Device
RS-232 Device
Rx
G
Tx RxTxG
RS-232 IR
RxTx
RS-232
V
OVER DTP
REMOTE
Figure 8. RS-232 Connector Wiring
NOTES:
• The IR Tx and Rx line pair and the RS-232 Tx and Rx line pair must each cross
once between this connector and the source or destination.
• The length and preparation of exposed wires is important (see the audio connector
NOTES on page 6 for details).
DTP T/R DP 4K 330 and DTP T/R DP 4K 230 Twisted Pair Extenders • Installation and Operation 11
Front Panel Connection and Power Indicator
CONFIG
AAA AAA BBB
ReceiverTransmitter
Figure 9. Transmitter and Receiver Front Panel Connector and Indicator
A
Power (and signal) LED (both units) —
Amber — The unit is receiving power, either locally or remotely (on the DTP cable).
Green — The unit is powered and is receiving an active digital input, either on the
DisplayPort input if a transmitter, or transmitted on the DTP cable if a receiver.
B
Configuration port (receiver only) — This USB mini-B port is used to configure video
and EDID settings and to update firmware.
Operation
After the transmitter, the receiver, and their connected devices are powered up, the system is
fully operational. If any problems are encountered, ensure all cables are routed and
connected properly.
NOTE: Ensure that the video source and display selected for the DDC are properly
connected to the transmitter and receiver pair, and that the transmitter, the receiver,
and the display have power applied before power is applied to the video source. If the
other devices are not turned on before the video source, the image may not appear.
Use and Compatibility with Other Extron DTP Products
The Extenders are compatible with the full line of Extron DTP products. When they are used
with DTP 330 and DTP 230 HDMI and DVI transmitters or receivers:
• The supported pixel clock rate is up to 300 Mhz.
• The supported resolutions are up to 3840x2160 @ 30 Hz or 4096x2160 @ 30 Hz with
multi-channel audio.
The Extenders can also be used with presentation switchers such as the MPS 602 or the
IN1608, but the pixel clock rate is limited to 165 Mhz.
NOTE: Some older DP sources do not support audio. Audio on these older sources is
not supported when DTP 330 or DTP 230 DP transmitters are used with DTP 330 or
DTP 230 HDMI receivers.
DTP T/R DP 4K 330 and DTP T/R DP 4K 230 Twisted Pair Extenders • Remote Control 12
Remote Control
The DTP R DP 4K 330 and DTP R DP 4K 230 receivers can be remotely controlled using
either Extron SIS commands or Product Configuration Software from a host device such as
a computer or control system via their front panel configuration (USB) ports (see item
B
on
the previous page).
This section includes:
• Simple Instruction Set Control
• Product Configuration Software
Simple Instruction Set Control
Host-to-Receiver Communications
SIS commands consist of one or more characters per field. No special characters are
required to begin or end a command character sequence. When a command is valid, the
receiver executes the command and sends a response to the host device. All responses
from the receiver to the host end with a carriage return and a line feed (CR/LF =
]
), which
signals the end of the response character string. A string is one or more characters.
Receiver-Initiated Message
When power is applied, the receiver responds by sending the following copyright message
to the host:
© Copyright 20yy, Extron Electronics DTP R DTP 4K 230/330, Vx.xx, 60-nnnn-nn
]
Vx.xx is the firmware version number and 60-nnnn-nn is the part number.
Error responses
When the receiver receives a valid SIS command, it executes the command and sends a
response to the host device. If the receiver is unable to execute the command because the
command is invalid or it contains invalid parameters, the receiver returns an error response
to the host. The error response codes are:
E10 — Invalid command
E13 — Invalid parameter
Timeout
Pauses of 10 seconds or longer between command ASCII characters result in a timeout.
The command operation is aborted with no other indication.
DTP T/R DP 4K 330 and DTP T/R DP 4K 230 Twisted Pair Extenders • Remote Control 13
Using the Command and Response Table
The command and response table begins below. Symbols are used throughout the table
to represent variables in the command and response fields. Command and response
examples are shown throughout the table. The SIS commands are not case sensitive. The
ASCII to HEX conversion table below is for use with the command and response table.
ASCII to Hex Conversion Table
•
Space
Symbol Definitions
]
= Carriage return/line feed
}
= Carriage return (no line feed)
| = Pipe (can be used interchangeably with the
}
character)
• = space
E
= Escape key
W = Can be used interchangeably with the
E
character
X! = Signal status 0 = Undetected 1 = Detected
X@ =
EDID
1
= HDMI 1080p60, 2 channel 2 = Input EDID
3
= User assignable value (via Product Configuration Software)
X#
= Verbose mode
0
= Clear/none
2
= Tagged responses for queries
1
= Verbose mode (default)
3
= Verbose mode and tagged for queries
X$ = Unit name A text string of up to 24 alphanumeric characters and minus sign/hyphen (-).
No blank or space characters are permitted as part of a name. The first character must
be a letter, and the last character must not be a minus sign/hyphen.
X% =
Firmware version number to second decimal place (x.xx)
Command and Response Table for SIS Commands
Command Function
SIS Command
(Host to Unit)
Response
(Unit to Host)
Additional description
Signal status
Show input and output status
E
0LS
} X!
*
X!]
Verbose mode 2 and 3:
E
0LS
}
Sig
X!
*
X!]
EDID minder
Assign EDID
E
A
X@
EDID
}
EdidA
X@]
Assign EDID
X@
to input.
Example:
E
A1EDID
}
EdidA1
]
Show EDID assignment
E
AEDID
} X@]
Verbose mode 2 and 3:
E
AEDID
}
EdidA
X@]
Verbose mode
Set verbose mode
EX#
CV
}
Vrb
X#]
Show verbose mode
E
CV
} X#]
Verbose mode 2 and 3:
E
CV
}
Vrb
X#]
Command and Response Table for SIS Commands (continued)
DTP T/R DP 4K 330 and DTP T/R DP 4K 230 Twisted Pair Extenders • Remote Control 14
Command Function
SIS Command
(Host to Unit)
Response
(Unit to Host)
Additional description
Unit name
Set unit name
EX$
CN
}
Ipn•
X$]
Set unit name to
X$
.
Set unit name to factory default
E
•
CN
}
Ipn
•
DTP-R-DP-4K-230
]
Unit name depends on model.
Ipn
•
DTP-R-DP-4K-330
]
Show unit name
E
CN
} X$]
Verbose mode 2 and 3:
E
CN
}
Ipn•
X$]
Information requests
Request part number
N
60-nnnn-nn
]
See www.extron.com for part
numbers.
Verbose mode 2 and 3:
N
Pno
•
60-nnnn-nn
]
Query controller firmware version
Q
X&
]
Example:
Q
1.23
]
The factory-installed controller firmware
version is 1.23 (sample value only).
Product Configuration Software
This section details the Extron Product Configuration Software (PCS), available on the
Extron website. The Windows-based PCS communicates with the unit via the front panel
configuration port, a standard USB mini-B port (see item
B
on page 11).
Installing the Software
PCS and Firmware Loader are available on the Extron website. Download and install both
programs as follows:
NOTES:
• This procedural description is illustrated as using Internet Explorer. Depending on
the browser you use, some steps or indications may be different.
•
Steps 1 thr
ough 7, below, are also used to download firmware update packages.
1.
Go to
www.extron.com and click the
Download tab (see figure 10,
1
).
OR
1111111111
22
22222222
22
22222222
33
33333333
Figure 10. Selecting the Download Tab
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
Extron DTP R DP 4K 230 Manuel utilisateur
- Taper
- Manuel utilisateur
- Ce manuel convient également à
dans d''autres langues
- English: Extron DTP R DP 4K 230 User manual
Documents connexes
-
Extron DTP T DWP 4K D Series Manuel utilisateur
-
Extron DTP T HWP 4K 231 D Manuel utilisateur
-
-
-
-
Extron DTP2 T 202 FB Manuel utilisateur
-
-
-
Extron DTP T FB 332 Manuel utilisateur
-
Extron DTP R HWP 4K 331 D Manuel utilisateur