Kichler Lighting 44271PN Manuel utilisateur

Taper
Manuel utilisateur
IS-44271-CB
We’re here to help 866-558-5706
Hrs: M-F 9am to 5pm EST
1) Find the appropriate threaded holes on mounng strap[A] that
align with hole distance in canopy. Thread mounng screws[D] into
threaded holes starng from outlet box[B] side.
2) Aach mounng strap to outlet box with strap mounng screws[C].
Mounng strap can be adjusted to suit posion of xture.
3) Grounding instrucons: (See Illus. I or II).
a) On xtures where mounng strap is provided with a hole and
two raised dimples. Wrap ground wire from outlet box around
green ground screw, and thread into hole.
b) On xtures where a cupped washer is provided. Aach ground
wire from outlet box under cupped washer and green ground
screw, and thread into mounng strap.
If xture is provided with ground wire. Connect xture ground wire
to outlet box ground wire with wire connector (not provided.) aer
following the above steps. Never connect ground wire to black or
white power supply wires.
4) Make wire connecons. Reference chart below for correct
connecons and wire accordingly.
Connect Black or Red
Supply Wire to:
Connect White Supply Wire to:
Black White
*Parallel cord (round & smooth) *Parallel cord (square & ridged)
Clear, Brown, Gold or Black
without Tracer
Clear, Brown, Gold or Black
with Tracer
Insulated wire (other than
green) with copper conductor
Insulated wire (other than
green) with silver conductor
*Note: When parallel wire (SPT 1 & SPT
2) are used. The neutral wire is square
shaped or ridged and the other wire
will be round in shape or smooth
(see illus.)
Neutral Wire
5) Push xture to wall carefully passing mounng screws with holes
in canopy. Note: xture can be mounted with glass in the up or
down posion. Make sure all wires are inside canopy and do not get
pinched between wall and canopy of xture.
6) Place the two (2) lockwashers[G] onto screws coming through
canopy and thread the two (2) lockup knobs[H] onto mounng
screws and ghten to secure xture to wall.
7) Insert recommended bulb[E] (not supplied).
8) Carefully raise glass[F] to the xture. Slip the smaller opening over
the socket and t the glass against the socket cover and gently rotate
clockwise into place.
GREEN GROUND
SCREW
CUPPED
WASHER
OUTLET BOX
GROUND
FIXTURE
GROUND
DIMPLES
WIRE CONNECTOR
OUTLET BOX
GROUND
GREEN GROUND
SCREW
FIXTURE
GROUND
I
II
Fixture Diagram
Parts List
[A] Mounting Strap
[B] Outlet Box
[C] Strap Mounting
Screws
[D] Mounting
Screws
[E] Bulb
[F] Glass
[G] Lockwashers
[H] Lockup Knobs
Cauons
CAUTION – RISK OF SHOCK –
Disconnect Power at the main circuit breaker panel or main
fusebox before starng and during the installaon.
WARNING:
This xture is intended for installaon in accordance
with the Naonal Electrical Code (NEC) and all local code
specicaons. If you are not familiar with code requirements,
installaon by a cered electrician is recommended.
Installaon Instrucons
B
F
A
C
E
D
G
H
IS-44271-CB
Nous sommes là pour vous aider 866-558-5706
Heures : du lundi au vendredi, de 9h à 17h (heure de l’Est)
INSTRUCTIONS:
For Assembling and Installing Fixtures in Canada
Pour Lassemblage et L’installaon Au Canada
1) Find the appropriate threaded holes on mounng strap[A] that
align with hole distance in canopy. Thread mounng screws[D] into
threaded holes starng from outlet box[B] side.
2) Visser la barree de montage à la boite de joncon vis de xaon de
la sangle[C]. La barree de montage peut etre ajustée pour convenir
à la posion de lapplique..
3) Connecter les ls. Se reporter au tableau ci-dessous pour faire les
connexions.
Connecter le l noir ou
rouge de la boite
Connecter le l blanc de la
boîte
A Noir A Blanc
*Au cordon parallèle (rond et
lisse)
*Au cordon parallèle (à angles
droits el strié)
Au transparent, doré, marron,
ou noir sans l disncf
Au transparent, doré, marron,
ou noir avec un l disncf
Fil isolé (sauf l vert) avec
conducteur en cuivre
Fil isolé (sauf l vert) avec
conducteur en argent
*Remarque: Avec emploi d’un l
paralléle (SPT 1 et SPT 2). Le l neutre
est á angles droits ou strié et lautre l
doit étre rond ou lisse (Voir le schéma).
Fil Neutre
4) Pousser le luminaire contre le mur, en passant avec soin les vis de
montage à travers les trous dans le couvercle. Note: xture can be
mounted with glass in the up or down posion. Vous assurer que
tous les ls sont dans le couvercle et ne se retrouvent pas pincés
entre le couvercle et le mur.
5) Place the two (2) lockwashers[G] onto screws coming through
canopy and thread the two (2) lockup knobs[H] onto mounng
screws and ghten to secure xture to wall.
6) Installer la ou les ampoules[E] recommandées (non fournies).
7) Carefully raise glass[F] to the xture. Slip the smaller opening over
the socket and t the glass against the socket cover and gently rotate
clockwise into place.
Diagramme d’appareils
ATTENTION – RISQUE DE DÉCHARGES ÉLECTRIQUES -
Couper le courant au niveau du panneau du disjoncteur du
circuit principal ou de la boîte à fusibles principale avant de
procéder à l’installaon.
ATTENTION:
Ce luminaire doit être installé conformément aux codes
d’électricité naonaux (NEC) et sasfaire toutes les
spécicaons des codes locaux. Si vous ne connaissez pas
les exigences de ces codes, il est recommandé de coner
l’installaon à un électricien ceré.
Liste des Pièce
Précauons
Instrucons d’installaon
[A] Étrier de
Montage
[B] Boîte  Prises
[C] Vis de Fixation
de la Sangle
[D] Vis De Montage
[E] Ampoules
[F] Verre
[G] Rondelle de
Blocage
[H] Boule de Blocage
B
F
A
C
E
D
G
H
  • Page 1 1
  • Page 2 2

Kichler Lighting 44271PN Manuel utilisateur

Taper
Manuel utilisateur

dans d''autres langues