Simplicity 2691250-00 Manuel utilisateur

Not for

Reproduction

80012960LAMI

Revision: A

en

ar

es

fr

pt

sw

tr

Operator’s Manual - Front-Engine Rider

Manual del Operario - Carretilla con motor frontal

Manuel d'utilisation - Tracteur à moteur avant

Manual do Operador - Trator cortador de grama com motor frontal

Mwongozo wa Mwendeshaji - Kiendesha Injini ya Mbele

Kullanma Kılavuzu - Önden Motorlu Çim Biçme Traktörü

Not for

Reproduction

2

1723143

A

B

C

1

2

3

4

5

6

7

8

9

10

1

B

D

C

A

2

12V

STOPSTOP

D

Not for

Reproduction

3

en

1888.8

AIR FILTER CHANGE

9:18 am

RPM x 1000

1

2

3

A B C

GE

D

H I JF K

4

6

A

B

C

10 psi

(0,68 bar)

12-14 psi

(0,82-0,96 bar)

5

Not for

Reproduction

4

7

A

B

C

9

A B

10

8

A

D

Not for

Reproduction

5

en

11

12

A

B

C

.030˝

(0.76 mm)

13

14

MODEL: XXXXXX

TYPE: XXXX XX

CODE: XXXXXXXX

15

Not for

Reproduction

6

16

4

3

2

1

4

3

2

1

17

Not for

Reproduction

7

en

Products Covered by This Manual

The following products are covered by this manual:

2691250-00

CONTENTS

Operator Safety .............................................................. 8

Features and Controls..................................................... 13

Operation ........................................................................ 16

Safety Interlock System Tests ......................................... 16

Maintenance ................................................................... 20

Troubleshooting .............................................................. 24

Specications ................................................................. 26

The images in this document are representative. Your unit may vary from the images displayed.

LEFT and Right are see from the operator's position

Not for

Reproduction

8

DANGER indicates a hazard which, if not

avoided, will result in death or serious injury.

WARNING indicates a hazard which, if not

avoided, could result in death or serious injury.

CAUTION indicates a hazard which, if not

avoided, could result in minor or moderate

injury.

NOTICE indicates a situation that could result in

damage to the product.

WARNING

The engine exhaust from this product contains

chemicals known to the State of California to cause

cancer, birth defects, or other reproductive harm.

WARNING

Certain components in this product and its related

accessories contain chemicals known to the State

of California to cause cancer, birth defects, or other

reproductive harm. Wash hands after handling.

WARNING

Battery posts, terminals, and related accessories

contain lead and lead compounds - chemicals known to

the State of California to cause cancer, birth defects, or

other reproductive harm. Wash hands after handling.

WARNING

Running engine gives off carbon monoxide, an

odorless, colorless, poison gas.

Breathing carbon monoxide can cause headache,

fatigue, dizziness, vomiting, confusion, seizures,

nausea, fainting or death.

• Operate equipment ONLY outdoors.

• Keep exhaust gas from entering a confined area through

windows, doors, ventilation intakes, or other openings.

Operator Safety

Important Safety Instructions

SAVE THESE INSTRUCTIONS - This manual contains

important instructions that should be followed during the

initial set-up, the operation, and the maintenance of the

equipment. Save these original instructions for future

reference.

Safety Symbols and Meanings

The safety alert symbol is used to identify safety

information about hazards that can result in personal injury.

A signal word (DANGER, WARNING, or CAUTION) is used

with the alert symbol to indicate the likelihood and the

potential severity of injury. In addition, a hazard symbol may

be used to represent the type of hazard.

FIRE MOVING

PARTS

SHOCK STOP

TOXIC

FUMES

KICKBACK EXPLOSION ON OFF

WEAR EYE

PROTECTION

HAZARDOUS

CHEMICAL

HOT

SURFACE

CHOKE

READ

MANUAL

FAST SLOW OIL FUEL

FUEL

SHUT-OFF

FUEL AMPUTATION

HAZARD

ROLL-OVER

HAZARD

Not for

Reproduction

9

en

GENERAL OPERATION

1. Read, understand, and follow all instructions in the manual

and on the unit before starting.

2. Do not put hands or feet near rotating parts or under the

machine. Keep clear of the discharge opening at all times.

3. Only allow responsible adults, who are familiar with the

instructions, to operate the unit (local regulations can

restrict operator age).

4. Clear the area of objects such as rocks, toys, wire, etc.,

which could be picked up and thrown by the blade(s).

5. Be sure the area is clear of other people before mowing.

Stop the unit if anyone enters the area.

6. Never carry passengers.

7. Do not mow in reverse unless absolutely necessary.

Always look down and behind before and while travelling in

reverse.

8. Never direct discharge material toward anyone. Avoid

discharging material against a wall or obstruction.

Material may ricochet back toward the operator. Stop the

blade(s) when crossing gravel surfaces.

9. Do not operate the machine without the entire grass

catcher, discharge guard (deflector), or other safety

devices in place.

10. Slow down before turning.

11. Never leave a running unit unattended. Always disengage

the PTO, set parking brake, stop engine, and remove

starter key from tractor.

12. Disengage blades (PTO) when not mowing. Shut off

engine and wait for all parts to come to a complete stop

before cleaning the machine, removing the grass catcher,

or unclogging the discharge guard.

13. Operate the machine only in daylight or good artificial light.

14. Do not operate the unit while under the influence of alcohol

or drugs.

15. Watch for traffic when operating near or crossing

roadways.

16. Use extra care when loading or unloading the unit into a

trailer or truck.

17. Always wear eye protection when operating this unit.

18. Data indicates that operators, age 60 years and above,

are involved in a large percentage of power equipment-

related injuries. These operators should evaluate their

ability to operate the equipment safely enough to protect

themselves and others from injury.

19. Follow the manufacturer’s recommendations for wheel

weights or counterweights.

20. Keep in mind the operator is responsible for accidents

occurring to other people or property.

21. All drivers should seek and obtain professional and

practical instruction.

22. Always wear substantial footwear and trousers. Never

operate when barefoot or wearing sandals.

23. Before using, always visually check that the blades and

blade hardware are present, intact, and secure. Replace

worn or damaged parts.

24. Disengage attachments before: refueling, removing an

attachment, making adjustments (unless the adjustment

can be made from the operator’s position).

25. When the machine is parked, stored, or left unattended,

lower the cutting means unless a positive mechanical lock

is used.

26. Before leaving the operator’s position for any reason,

engage the parking brake, disengage the PTO, stop the

engine, and remove the starter insert.

27. To reduce fire hazard, keep the unit free of grass, leaves,

& excess oil. Do not stop or park over dry leaves, grass, or

combustible materials.

TRANSPORTING AND STORAGE

1. When transporting the unit on an open trailer, make sure

it is facing forward, in the direction of travel. If the unit is

facing backwards, wind lift could damage the unit.

2. Always observe safe refueling and fuel handling practices

when refueling the unit after transportation or storage.

3. Never store the unit (with fuel) in an enclosed poorly

ventilated structure. Fuel vapors can travel to an ignition

source (such as a furnace, water heater, etc.) and cause

an explosion. Fuel vapor is also toxic to humans and

animals.

4. Always follow the engine manual instructions for storage

preparations before storing the unit for both short and long

term periods.

5. Always follow the engine manual instructions for proper

start-up procedures when returning the unit to service.

6. Never store the unit or fuel container inside where there is

an open flame or pilot light, such as in a water heater. Allow

unit to cool before storing.

Read these safety rules and follow them closely. Failure to obey these rules could result in loss of control of unit,

severe personal injury or death to you, or bystanders, or damage to property or equipment. This mowing deck

is capable of amputating hands and feet and throwing objects. The triangle in text signifies important

cautions or warnings which must be followed.

Not for

Reproduction

10

WARNING

Never operate on slopes greater than 17.6 percent (10°)

which is a rise of 3-1/2 feet (106 cm) vertically in 20 feet

(607 cm) horizontally.

When operating on slopes use additional wheel weights

or counterweights. See your dealer/retailer to determine

which weights are available and appropriate for your

unit.

Select slow ground speed before driving onto slope.

In addition to front weights, use extra caution when

operating on slopes with rear-mounted grass catchers.

Mow UP and DOWN the slope, never across the face,

use caution when changing directions and DO NOT

START OR STOP ON SLOPE.

CHILDREN

Tragic accidents can occur if the operator is not alert to the

presence of children. Children are often attracted to the unit

and the mowing activity. Never assume that children will

remain where you last saw them.

1. Keep children out of the mowing area and under the

watchful care of another responsible adult.

2. Be alert and turn unit off if children enter the area.

3. Before and during reverse operation, look behind and

down for small children.

4. Never carry children, even with the blade(s) off. They may

fall off and be seriously injured or interfere with safe unit

operation. Children who have been given rides in the past

may suddenly appear in the mowing area for another ride

and be run over or backed over by the machine.

5. Never allow children to operate the unit.

6. Use extra care when approaching blind corners, shrubs,

trees, or other objects that may obscure vision.

SLOPE OPERATION

Slopes are a major factor related to loss-of-control and tip-

over accidents, which can result in severe injury or death.

Operation on all slopes requires extra caution. If you

cannot back up the slope or if you feel uneasy on it, do not

operate on it.

Control of a ride-on machine sliding on a slope will not be

regained by the application of the brake. The main reasons

for loss of control are: insufficient tire grip on the ground,

speed too fast, inadequate braking, the type of machine

is unsuitable for its task, lack of awareness of the ground

conditions, incorrect hitching and load distribution.

1. Mow up and down slopes, not across.

2. Watch for holes, ruts, or bumps. Uneven terrain could

overturn the unit. Tall grass can hide obstacles.

3. Choose a slow speed so that you will not have to stop or

change speeds while on the slope.

4. Do not mow on wet grass. Tires may lose traction.

5. Always keep unit in gear especially when traveling down

slopes. Do not shift to neutral and coast downhill.

6. Avoid starting, stopping, or turning on a slope. If tires

lose traction, disengage the blade(s) and proceed slowly

straight down the slope.

7. Keep all movement on slopes slow and gradual. Do

not make sudden changes in speed or direction, which

could cause the machine to rollover.

8. Use extra care while operating machines with grass

catchers or other attachments; they can affect the

stability of the unit. Do not use on steep slopes.

9. Do not try to stabilize the machine by putting your foot on

the ground (ride-on units).

10. Do not mow near drop-offs, ditches, or embankments.

The mower could suddenly turn over if a wheel is over

the edge of a cliff or ditch, or if an edge caves in.

11. Do not use grass catchers on steep slopes.

12. Do not mow slopes if you cannot back up them.

13. See your authorized dealer/retailer for recommendations

of wheel weights or counterweights to improve stability.

14. Remove obstacles such as rocks, tree limbs, etc.

15. Use slow speed. Tires may lose traction on slopes even

through the brakes are functioning properly.

16. Do not turn on slopes unless necessary, and then, turn

slowly and gradually downhill, if possible.

TOWED EQUIPMENT (RIDE-ON UNITS)

1. Tow only with a machine that has a hitch designed for

towing. Do not attach towed equipment except at the

hitch point.

2. Follow the manufacturer’s recommendations for weight

limit for towed equipment and towing on slopes.

3. Never allow children or others in or on towed equipment.

4. On slopes, the weight of the towed equipment may

cause loss of traction and loss of control.

5. Travel slowly and allow extra distance to stop.

6. Do not shift to neutral and coast down hill.

Not for

Reproduction

11

en

SERVICE AND MAINTENANCE

Safe Handling of Gasoline

1. Extinguish all cigarettes, cigars, pipes, and other sources

of ignition.

2. Use only approved gasoline containers.

3. Never remove the gas cap or add fuel with the engine

running. Allow the engine to cool before refueling.

4. Never fuel the machine indoors.

5. Never store the machine or fuel container where there is an

open flame, spark, or pilot light such as near a water heater

or other appliance.

6. Never fill containers inside a vehicle or on a truck bed with

a plastic bed liner. Always place containers on the ground

away from your vehicle before filling.

7. Remove gas-powered equipment from the truck or

trailer and refuel it on the ground. If this is not possible,

then refuel such equipment on a trailer with a portable

container, rather than from a gasoline dispenser nozzle.

8. Keep nozzle in contact with the rim of the fuel tank or

container opening at all times until fueling is complete. Do

not use a nozzle lock-open device.

9. If fuel is spilled on clothing, change clothing immediately.

10. Never over-fill the fuel tank. Replace gas cap and tighten

securely.

11. Use extra care in handling gasoline and other fuels. They

are flammable and vapors are explosive.

12. If fuel is spilled, do not attempt to start the engine but

move the machine away from the area of spillage and

avoid creating any source of ignition until fuel vapors have

dissipated.

13. Replace all fuel tank caps and fuel container caps securely.

Service & Maintenance

1. Never run the unit in an enclosed area where carbon

monoxide fumes may collect.

2. Keep nuts and bolts, especially blade attachment bolts,

tight and keep equipment in good condition.

3. Never tamper with safety devices. Check their proper

operation regularly and make necessary repairs if they are

not functioning properly.

4. Keep unit free of grass, leaves, or other debris build-up.

Clean up oil or fuel spillage and remove any fuel-soaked

debris. Allow machine to cool before storage.

5. If you strike an object, stop and inspect the machine.

Repair, if necessary, before restarting.

6. Never make adjustments or repairs with the engine

running.

7. Check grass catcher components and the discharge guard

frequently and replace with manufacturer’s recommended

parts, when necessary.

8. Mower blades are sharp. Wrap the blade or wear gloves,

and use extra caution when servicing them.

9. Check brake operation frequently. Adjust and service as

required.

10. Maintain or replace safety and instructions labels, as

necessary.

11. Do not remove the fuel filter when the engine is hot as

spilled gasoline may ignite. Do not spread fuel line clamps

further than necessary. Ensure clamps grip hoses firmly

over the filter after installation.

12. Do not use gasoline containing METHANOL, gasohol

containing more than 10% ETHANOL, gasoline additives,

or white gas because engine/fuel system damage could

result.

13. If the fuel tank must be drained, it should be drained

outdoors.

14. Replace faulty silencers/mufflers.

15. Use only factory authorized replacement parts when

making repairs.

16. Always comply with factory specifications on all settings

and adjustments.

17. Only authorized service locations should be utilized for

major service and repair requirements.

18. Never attempt to make major repairs on this unit unless

you have been properly trained. Improper service

procedures can result in hazardous operation, equipment

damage and voiding of manufacturer’s warranty.

19. On multiple blade mowers, take care as rotating one blade

can cause other blades to rotate.

20. Do not change engine governor settings or over-speed

the engine. Operating the engine at excessive speed can

increase the hazard of personal injury.

21. Disengage drive attachments, stop the engine, remove the

starter insert, and disconnect the spark plug wire(s) before:

clearing attachment blockages and chutes, performing

service work, striking an object, or if the unit vibrates

abnormally. After striking an object, inspect the machine for

damage and make repairs before restarting and operating

the equipment.

22. Never place hands near the moving parts, such as a hydro

pump cooling fan, when the tractor is running. (Hydro

pump cooling fans are typically located on top of the

transaxle).

23. Units with hydraulic pumps, hoses, or motors:

WARNING: Hydraulic fluid escaping under pressure may

have sufficient force to penetrate skin and cause serious

injury. If foreign fluid is injected into the skin it must be

surgically removed within a few hours by a doctor familiar

with this form of injury or gangrene may result. Keep

body and hands away from pin holes or nozzles that

eject hydraulic fluid under high pressure. Use paper or

cardboard, and not hands, to search for leaks. Make sure

all hydraulic fluid connections are tight and all hydraulic

hoses and lines are in good condition before applying

pressure to the system. If leaks occur, have the unit

serviced immediately by your authorized dealer.

24. WARNING: Improper release of springs can result in

serious personal injury. Springs should be removed by an

authorized technician.

25. Models equipped with an engine radiator:

WARNING: To prevent serious bodily injury from hot coolant

or steam blow-out, never attempt to remove the radiator

cap while the engine is running. Stop the engine and wait

until it is cool. Even then, use extreme care when removing

the cap.

Not for

Reproduction

12

Safety Decals

See Figures 1and 2 (callouts A to E) for location and

pictures of decals.

All and instructional messages on your rider and mower

should be carefully read and obeyed. Personal bodily injury

can result when these instructions are not followed. The

information is for your safety and it is important! The safety

decals below are on your rider and mower.

If any of these decals are lost or damaged, replace them at

once. See an authorized dealer for replacements.

These labels are easily applied and will act as a constant

visual reminder to you, and others who may use the

equipment, to follow the safety instructions necessary for

safe, effective operation.

Callout Decal Description

A

DANGER - Main Panel

B

Danger,

Thrown Objects Hazard

C

Danger,

Amputation and Thrown Objects Hazard

D

Decal:

Attachment Lift

Safety Icon

See Figure 1 (callouts B to D) for location of icons. See

below for an explanation of these icons.

1. WARNING: Read and understand the Operator’ Manual

before using this machine. Know the location and

function of all controls. Do not operate this machine

unless you are trained.

2. DANGER - LOSS OF TRACTION, SLIDING,

STEERING AND CONTROL ON SLOPES HAZARD:

If machine stops forward motion or starts sliding on a

slope, stop the blades and drive slowly off the slope.

3. DANGER: FIRE HAZARD: Keep unit free of grass,

leaves and excess oil. Do not add fuel while engine is

hot or running. Stop engine, remove key and allow to

cool for at least 3 minutes prior to adding fuel. Do not

add fuel indoors, in an enclosed trailer, garage or other

enclosed areas. Clean up spilled fuel. Do not smoke

while operating this machine.

4. DANGER - TIPPING AND SLIPPING HAZARD: Mow

up and down slopes not across. Do not operate on

slopes over 10 degrees. Avoid sudden and sharp (fast)

turns while on slopes.

5. DANGER - AMPUTATION AND DISMEMBERMENT

HAZARD: To avoid injury from rotating blades and

moving parts, keep safety devices (guards, shields and

switches) in place and working.

6. Do not mow when children or others are around. Never

carry riders especially children even with the blades off.

Do not mow in reverse unless absolutely necessary.

Look down and behind – before and while backing.

7. Consult technical literature before performing technical

repairs or maintenance. When leaving the machine,

shutoff engine, set the parking brake to the lock position

and remove the ignition key.

8. Keep by-standers and children a safe distance away.

Remove objects that can be thrown by the blade. Do not

mow without discharge chute in place.

9. Do not mow without discharge chute or entire grass

catcher in place.

10. To avoid injury from rotating blades, stay clear of deck

edge and keep others away.

Not for

Reproduction

13

en

Power Take-Off (PTO) Switch

The PTO (Power Take-Off ) switch engages and

disengages the mower blade clutch. To engage

the PTO, pull UP on the switch. Push DOWN to

disengage.

NOTE: The operator must be seated rmly in the

tractor seat for the PTO to function.

Reverse Mowing Option (RMO)

This allows the operator to mow (or use other

PTO driven attachments) while traveling in

reverse. To activate, turn the RMO key after the

PTO is engaged. The L.E.D. light will illuminate,

and the operator can then mow in reverse. Each

time the PTO is engaged, the RMO needs to be

reactivated if desired.

STOPSTOP

Start/Stop Push Button

• Press and hold the push button to start the

engine.

• Press the push button when the engine is

running to shut down the engine.

Throttle Control

This controls the engine speed. Move the throttle

control FORWARD to increase engine speed and

BACK to decrease engine speed. Always operate

at FULL throttle.

Transmission Release Lever

This releases the transmission so that the tractor

can be pushed by hand.

Choke

Close the choke for cold starting. Open the choke

once the engine starts. A warm engine may not

require choking. Move the lever forward to close

the choke.

Differential Lock Pedal

Depressing this pedal locks the transmission

differential, locking both rear wheels into “drive”.

Use this feature if the tractor is stuck because

one wheel is slipping. Engage the differential lock

at slow ground speeds only.

Features and Controls

See Figure 2 for location.

Brake Pedal

Depressing the brake pedal applies the tractor

brake.

Cruise Control

The cruise control is used to lock the ground

speed control in forward. Move the lever forward

until the desired ground speed is reached. To

disengage the cruise control move the lever back.

In the event you need to stop quickly, depressing

the brake pedal will also return the cruise control

to neutral.

Electronic Panel

See Electronic Panel section.

Fuel Tank

To remove the cap, turn counterclockwise.

Ground Speed Pedals

The forward ground speed pedal controls the

tractor’s forward ground speed. The reverse

ground speed pedal controls the tractor’s reverse

ground speed.

Headlight Switch

This turns the tractor headlights on and off.

Height-of-Cut Switch

This adjusts the mower cutting height. Press the

switch UP to raise the mowing cutting height

and DOWN to lower the mower cutting height.

The height-of-cut is displayed on the electronic

dashboard.

Parking Brake

The parking brake knob is used to lock the

parking brake when the tractor is stopped. Fully

depressing the brake pedal and pulling up on the

knob engages the parking brake.

12V

Power Outlet (12V-DC)

The power outlet is 12V-DC. Accessories must be

rated at 9 amps or less.

Not for

Reproduction

14

Electronic Panel Features

The electronic panel (Figure 3) displays the operating

status of a variety of equipment and engine parameters,

and provides clock and timer functions for oil and air

filter maintenance and for tracking work hours. Data is

retained if the battery is disconnected or power is otherwise

interrupted.

NOTE: The Deck Height display (see below) requires a

wire harness connection between the deck and the tractor.

Ensure this connection is made when reinstalling the deck

after maintenance or the Deck Height display will not func-

tion.

A. Fuel Level – illuminated bars indicate approximate level

of fuel in the tank; at two bars the fuel pump icon will

flash, reminding you to add fuel.

B. Tachometer – indicates engine speed from 1000 to

4000 RPM.

C. Deck Height – illuminated bars indicate approximate

height of the deck while mowing.

D. Control Buttons – MODE (top button), UP (center

button), and DOWN (bottom button).

E. Hour Meter – displays total accumulated run hours by

default; trip hours when MODE button is pressed.

F. Headlight Icon – illuminates when the headlights are

on.

G. Parking Brake Icon – illuminates when the parking

brake is engaged.

H. Message Display – alerts operator to maintenance

requirements.

I. Tractor Icon – illuminates when the cruise control is

engaged.

J. Blade Icon – illuminates when the Power Takeoff (PTO)

is engaged.

K. Clock Display – 12-hour clock with am/pm.

Timer and Clock Settings

The Hour Meter (H) displays total accumulated run hours

by default. It will automatically reset to zero when the meter

reaches 1999.9 hours.

TRIP HOURS – Press the MODE button once to display

Trip Hours. Press the MODE button again and hold for 3

seconds to reset the trip hours to zero.

OIL HOURS – Press the MODE button twice to display

Oil Hours. Press the MODE button again and hold for 3

seconds to reset the oil hours to zero after the oil and filter

have been changed.

AIR FILTER HOURS – Press the MODE button three times

to display Air Filter Hours. Press the MODE button again

and hold for 3 seconds to reset the air filter hours to zero

after the filter has been cleaned or changed.

CLOCK SET – Press the MODE button four times to adjust

the clock. Press the MODE button again and hold for 3

seconds to flash the hour, then press the UP or DOWN

button to change the hour. (AM and PM will change when

the hour setting is adjusted past 12 o’clock.) Press the

MODE button once to flash the minutes, then press the UP

or DOWN button to change the minutes. After adjusting

the hours and minutes, press the MODE button once more

to return to the normal clock display.

NOTE: If the MODE button is not pressed after ve sec-

onds, the selected display will not reset and the hour meter

will return to total accumulated hours.

Maintenance Messages

LOW BATTERY – This message will appear any time

a battery voltage problem occurs. The display will

automatically clear itself after the battery has been

serviced.

OIL CHANGE – This message appears after 50 hours of

run time since the previous reset. After changing the oil and

oil filter, press MODE twice to display OIL HRS, then press

and hold the MODE button for 3 seconds to reset the timer

to zero and clear the display.

CHECK AIR FILTER – This message appears after 25

hours of run time since the previous reset. After cleaning or

changing the air filter, press MODE three times to display

AIR FILTER HRS, then press and hold the MODE button for

3 seconds to reset the timer to zero and clear the display.

NOTE: When the LOW BATTERY message appears, it has

priority over any other messages. Service the battery rst,

then check for other maintenance messages.

Not for

Reproduction

15

en

12-Volt Power Outlet

The 12-volt accessory plug is located in the left side pod.

It can be used to power small electronic devices. The

accessory must be rated at 9 amps or less.

NOTICE: Operating a 12-volt accessory, especially with

the engine at idle, may cause battery discharge. When not

using the accessory plug it must be covered with the rubber

plug to prevent moisture from causing a short circuit. En-

trance of water into plug can cause a short circuit.

Automatic Controlled Traction

What is Automatic Controlled Traction?

Automatic Controlled Traction (ACT) is an exclusive feature

of our transmissions that provides improved traction. ACT

applies a preset amount of torque to both rear wheels even

if one starts slipping (a transmission without ACT will lose

traction completely if one rear wheel starts slipping). This

preset torque is just enough to provide additional traction,

and still allow the wheels to turn at different speeds in a tight

turn without damaging the lawn.

What to Expect from Your ACT Tractor

For the most part, while using your tractor you will not notice

ACT working, and you will simply become accustomed to

increased traction an ACT transmission provides.

Under certain circumstances the ACT system limit can be

exceeded, and one of the rear wheels may slip (for instance

if trying to turn up a hill while accelerating). This is normal. If

you start to lose traction, do not speed up. Instead, slow to

a stop, straighten the steering wheel, and slowly accelerate.

Stopping the tractor allows the transmission to regain more

traction.

Not for

Reproduction

16

Operation

General Operating Safety

Be sure to read all information in the Operator Safety

section before attempting to operate this unit. Become

familiar with all of the controls and how to stop the unit.

WARNING

If the unit does not pass a safety test, do not operate it.

See an authorized dealer.

Safety Interlock System Tests

This unit is equipped with a Safety Interlock System. Do not

attempt to bypass or tamper with the switches/devices.

Test 1 — Engine should NOT crank if:

• PTO switch is ON, OR

• Brake pedal is NOT fully depressed (parking brake OFF),

OR

• Operator is NOT in seat.

Test 2 — Engine SHOULD crank and start if:

• Operator is sitting in seat, AND.

• PTO switch is OFF, AND

• Brake pedal is fully depressed (parking brake ON).

Test 3 — Engine should SHUT OFF if:

• Operator rises off seat.

Test 4 — Check Mower Blade Stopping Time

Mower blades and mower drive belt should come to a

complete stop within five seconds after electric PTO switch

is turned OFF. If mower drive belt does not stop within five

seconds, see an authorized dealer.

Test 5 — Reverse Mow Option (RMO) Check

• Engine should shut off if reverse travel is attempted if

the PTO has been switched on and RMO has not been

activated.

• RMO light should illuminate when RMO has been

activated.

WARNING

Mowing in reverse can be hazardous to bystanders.

Tragic accidents can occur if the operator is not alert

to the presence of children. Never activate the RMO if

children are present. Children are often attracted to the

unit and the mowing activity.

Check Tire Pressure

Tires should be checked periodically to provide the

optimum traction and to guarantee the best cut (see Figure

4).

NOTE: These pressures may dier slightly from the “Maxi-

mum Ination” stamped on the side walls of the tires.

Oil Recommendations

We recommend the use of Briggs & Stratton Warranty

Certified oils for best performance. Other high-quality

detergent oils are acceptable if classified for service SF,

SG, SH, SJ or higher. Do not use special additives.

Outdoor temperatures determine the proper oil viscosity for

the engine. Use the chart to select the best viscosity for the

outdoor temperature range expected.

* Below 40°F (4°C) the use of SAE 30 will result in hard starting.

** Above 80°F (27°C) the use of 10W-30 may cause increased oil

consumption. Check oil level more frequently.

Not for

Reproduction

17

en

Check or Add Oil

Before adding or checking the oil

• Place the tractor on a level surface (see Figure 5).

• Clean the oil fill area of any debris.

1. Remove the dipstick (A, Figure 6) and wipe with a clean

cloth.

2. Insert and tighten the dipstick.

3. Remove the dipstick and check the oil level. It should be

at the FULL mark (B) on the dipstick.

4. If low, add oil slowly into the engine oil fill (C). Do not

overfill. After adding oil, wait one minute and then

recheck the oil level.

NOTE: Do not add oil at the quick oil drain (if equipped).

5. Replace and tighten the dipstick.

Oil Pressure

If the oil pressure is too low, a pressure switch (if equipped)

will either stop the engine or activate a warning device on

the equipment. If this occurs, stop the engine and check the

oil level with the dipstick.

If the oil level is below the ADD mark, add oil until it reaches

the FULL mark. Start the engine and check for proper

pressure before continuing to operate.

If the oil level is between the ADD and FULL marks, do not

start the engine. Contact an authorized dealer to have the

oil pressure problem corrected.

Fuel Recommendations

Fuel must meet these requirements:

• Clean, fresh, unleaded gasoline.

• A minimum of 87 octane/87 AKI (91 RON). High altitude

use, see below.

• Gasoline with up to 10% ethanol (gasohol) is acceptable.

NOTICE: Do not use unapproved gasolines, such as E15

and E85. Do not mix oil in gasoline or modify the engine to

run on alternate fuels. Use of unapproved fuels will damage

the engine components and void the engine warranty.

To protect the fuel system from gum formation, mix a fuel

stabilizer into the fuel. See Storage. All fuel is not the

same. If starting or performance problems occur, change

fuel providers or change brands. This engine is certified to

operate on gasoline. The emissions control system for this

engine is EM (Engine Modifications)

High Altitude

At altitudes over 5,000 feet (1524 meters), a minimum 85

octane/85 AKI (89 RON) gasoline is acceptable. To remain

emissions compliant, high altitude adjustment is required.

Operation without this adjustment will cause decreased

performance, increased fuel consumption, and increased

emissions. See an authorized Briggs & Stratton Dealer for

high altitude adjustment information.

Operation of the engine at altitudes below 2,500 feet

(762 meters) with the high altitude adjustment is not

recommended.

Adding Fuel

WARNING

Fuel and its vapors are extremely flammable and

explosive.

Fire or explosion can cause severe burns or death.

When Adding Fuel

• Turn engine off and let engine cool at least 3 minutes

before removing the fuel cap.

• Fill fuel tank outdoors or in well-ventilated area.

• Do not overfill fuel tank. To allow for expansion of the

fuel, do not fill above the bottom of the fuel tank neck.

• Keep fuel away from sparks, open flames, pilot lights,

heat, and other ignition sources.

• Check fuel lines, tank, cap, and fittings frequently for

cracks or leaks. Replace if necessary.

• If fuel spills, wait until it evaporates before starting

engine.

1. Clean the fuel cap area of dirt and debris. Remove the

fuel cap (A, Figure 7). Also see Features and Controls

section.

2. Fill the fuel tank (B) with fuel. To allow for expansion of

the fuel, do not fill above the bottom of the fuel tank neck

(C).

3. Reinstall the fuel cap.

Not for

Reproduction

18

Starting the Engine

WARNING

Fuel and its vapors are extremely flammable and

explosive.

Fire or explosion can cause severe burns or death.

When Starting Engine

• Ensure that spark plug, muffler, fuel cap, and air

cleaner (if equipped) are in place and secured.

• Do not crank engine with spark plug removed.

• If engine floods, set choke (if equipped) to OPEN/

RUN position, move throttle (if equipped) to FAST

position and crank until engine starts.

WARNING

Engines give off carbon monoxide, an odorless,

colorless, poison gas.

Breathing carbon monoxide can cause nausea, fainting,

or death.

Fire or explosion can cause severe burns or death.

• Start and run engine outdoors.

• Do not start or run engine in enclosed area, even if

doors or windows are open.

1. While sitting in the operator’s seat, fully depress the

brake pedal or set the parking brake.

2. Make sure that your feet are not depressing the ground

speed control pedals and that the cruise control lever is

in neutral.

3. Disengage the PTO clutch.

4. Set the engine speed control to the CHOKE position.

NOTE: A warm engine may not require choking.

5. Insert the ignition key and turn it to START.

6. After the engine starts, move the engine throttle control

to half speed. Warm up the engine by running it for at

least 30 seconds.

7. Set throttle to FULL.

In the event of an emergency the engine can be

stopped by simply turning the ignition switch to STOP.

Use this method only in emergency situations. For normal

engine shut down follow the procedure given in Stopping

the Tractor and Engine.

NOTE: If the engine does not start after repeated attempts,

contact an authorized dealer.

Driving the Tractor

1. Sit in the seat and adjust the seat so that you can

comfortably reach all the controls and see the

dashboard display (see Features and Controls).

2. Engage the parking brake. Fully depress the brake

pedal, pull UP on the parking brake control, and release

the brake pedal.

3. Make sure the PTO switch is disengaged.

4. Start the engine (see Starting the Engine).

5. Disengage the parking brake. Fully depress the brake

pedal, press DOWN on the parking brake control, and

release the brake pedal.

6. Depress the forward ground speed control pedal to

travel forward. Release the pedal to stop. Note that

the further down the pedal is depressed the faster the

tractor will travel.

7. Stop the tractor by releasing the ground speed control

pedals, setting the parking brake, and stopping the

engine (see Stopping the Tractor and Engine).

Mowing

1. Set the cutting height to the desired level using

the mower cutting height lever (see Features and

Controls).

2. Engage the parking brake. Make sure the PTO switch is

disengaged.

3. Start the engine (see Starting the Engine).

4. Set the throttle/choke control to the FAST position.

5. Engage the PTO to activate the mower blades.

6. Disengage the parking brake then begin mowing.

7. When finished mowing, shut off the PTO.

8. STOP the engine (see Stopping the

Tractor and Engine).

WARNING

The engine will shut off if the reverse ground speed

pedal is depressed while the PTO is on and the RMO

has not been activated. The operator should always turn

the PTO off prior to driving across on roads, paths, or

any area that may be used by other vehicles. Sudden

loss of drive could create a hazard.

Not for

Reproduction

19

en

Reverse Mowing Option (RMO)

WARNING

Mowing in reverse can be hazardous to bystanders.

Tragic accidents can occur if the operator is not alert

to the presence of children. Never activate the RMO if

children are present. Children are often attracted to the

unit and the mowing activity.

The Reverse Mowing Option (RMO) allows the operator

to mow in reverse (see Features and Controls). To

activate, turn the RMO key after the PTO is engaged. The

L.E.D. light will illuminate, and the operator can then mow

in reverse. Each time the PTO is engaged the RMO needs

to be reactivated if desired. The key should be removed to

restrict access to the RMO.

Pushing the Tractor by Hand

1. Disengage the PTO and turn the engine off.

2. Pull the transmission release (A, Figure 8) back

approximately 2-3/8" (6 cm) to lock into released

position.

3. The tractor can now be pushed by hand.

WARNING

Towing the unit will cause transmission damage. Do

not use another vehicle to push or pull this unit. Do not

actuate the transmission release lever while the engine

is running.

Adjusting the Mower Cutting Height

Use the mower cutting height adjustment lever to raise or

lower the cutting height (see Features and Controls).

The cutting height has seven positions between 1.5” and

4.0” (3,8 and 10,2 cm).

Parking Brake

Use the parking brake control to engage or disengage the

parking brake when the tractor is stopped (Features and

Controls).

Engage the Parking Brake - To engage the parking brake,

fully depress the brake pedal, pull UP on the parking brake

control, and release the brake pedal.

Disengage the Parking Brake - To disengage the parking

brake, fully depress the brake pedal, press DOWN on the

parking brake control, and release the brake pedal.

Stopping the Tractor and Engine

WARNING

Fuel and its vapors are extremely flammable and

explosive.

Fire or explosion can cause severe burns or death.

• Do not choke the carburetor to stop the engine.

1. Release the ground speed pedals to return to the

NEUTRAL position (see Features and Controls).

2. While still on the lawn, disengage the PTO switch, then

wait for all moving parts to stop.

3. Move the throttle control (or throttle/choke control)

to SLOW position and turn the ignition key to OFF.

Remove the key.

4. Engage the parking brake. Fully depress the brake

pedal, pull UP on the parking brake control, and release

the brake pedal.

In the event of an emergency the engine can be

stopped by simply turning the ignition switch to STOP.

Not for

Reproduction

20

ENGINE

First 5 Hours

Change engine oil

Every 8 Hours or Daily

Check engine oil level

Every 25 Hours or Annually *

Clean engine air filter and pre-cleaner **

Every 50 Hours or Annually *

Change engine oil

Replace oil filter

Annually

Replace air filter

Replace pre-cleaner

See Dealer Annually to

Inspect muffler and spark arrester

Replace spark plug

Replace fuel filter

Clean engine air cooling system

* Whichever comes first

** Clean more often in dusty conditions or when airborne debris is present.

Check Tire Pressure

Tires should be checked periodically to provide the

optimum traction and to guarantee the best cut (see Figure

4).

NOTE: These pressures may dier slightly from the “Maxi-

mum Ination” stamped on the side walls of the tires.

Check Mower Blade Stopping Time

WARNING

If the mower blade does not come to a complete stop

within 5 seconds, the clutch must be adjusted. Do not

operate the machine until the proper adjustment has

been performed by an authorized dealer.

Check the mower blade for proper function (see Safety

Interlock System Tests). The blade should stop rotating in

5 seconds or less after moving the blade control to the OFF

position.

Maintenance

Maintenance Chart

TRACTOR AND MOWER

Every 8 Hours or Daily

Check safety interlock system

Clean debris off tractor and mower deck

Clean debris from engine compartment

Every 25 Hours or Annually *

Check tire pressure

Check mower blade stopping time

Check tractor and mower for loose hardware

Every 50 Hours or Annually *

Clean battery and cables

Check tractor brakes

See Dealer Annually to

Lubricate tractor and mower

Check mower blades **

* Whichever comes first

** Check blades more often in regions with sandy soils or high dust

conditions.

WARNING

Unintentional sparking can result in fire or electric

shock.

Unintentional start-up can result in entanglement,

traumatic amputation, or laceration.

Before performing adjustments or repairs:

• Disconnect the spark plug wire and keep it away from

the spark plug.

• Disconnect battery at negative terminal (only engines

with electric start).

• Use only correct tools.

• Do not tamper with governor spring, links, or other parts

to increase engine speed.

• Replacement parts must be of the same design and

installed in the same position as the original parts. Other

parts may not perform as well, may damage the unit,

and may result in injury.

• Do not strike the flywheel with a hammer or hard object

because the flywheel may shatter during operation.

La page est en cours de chargement...

Simplicity 2691250-00 Manuel utilisateur

Ce manuel convient également à

Simplicity 2691250-00 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents