Kenmore 41179 Guide d'installation

Marque: Kenmore

Modèle: 41179

Taper: Guide d'installation

Ce manuel convient également à

41172
41173

INSTALLATION INSTRUCTIONS

Counter Depth Side by Side Refrigerator

IMPORTANT: READ AND SAVE THESE INSTRUCTIONS. INSTALLATION REQUIRES 2 OR MORE PEOPLE.

INSTRUCCIONES DE INSTALACIÓN

Refrigerador de dos puertas con profundidad de mostrador

IMPORTANTE: LEA Y GUARDE ESTAS INSTRUCCIONES. LA INSTALACIÓN REQUIERE DE 2 O MÁS PERSONAS.

INSTRUCTIONS D’INSTALLATION

Réfrigérateur côte à côte à profondeur de comptoir

IMPORTANT : LIRE ET CONSERVER CES INSTRUCTIONS.

L’INSTALLATION NÉCESSITE L’INTERVENTION DE 2 PERSONNES OU PLUS.

Table of Contents / Índice / Table des matières

ASSISTANCE OR SERVICE ....................2

REFRIGERATOR SAFETY.......................2

INSTALLATION REQUIREMENTS..........2

Tools and Parts .........................................2

Product Dimensions..................................3

Location Requirements ............................5

Electrical Requirements...........................5

Water Supply Requirements..................6

INSTALLATION INSTRUCTIONS...........6

Unpack the Refrigerator.........................6

Custom Door Panels................................ 7

Connect Water Supply ......................... 10

Plug in Refrigerator................................ 12

Prepare the Water System................... 12

Leveling and Door Closing ................... 12

Door Alignment....................................... 13

Complete Installation............................. 13

AYUDA O SERVICIO TÉCNICO...........14

SEGURIDAD DEL REFRIGERADOR ......14

REQUISITOS DE INSTALACIÓN .......... 15

Piezas y herramientas............................ 15

Medidas del producto...........................15

Requisitos de ubicación.........................17

Requisitos eléctricos ...............................18

Requisitos del suministro de agua....... 18

INSTRUCCIONES DE INSTALACIÓN... 19

Desempaque el refrigerador................19

Paneles para puerta a la medida....... 19

Conexión del suministro de agua....... 22

Cómo enchufar el refrigerador .......... 25

Preparación del sistema de agua ...... 25

Nivelación y cierre de la puerta ........ 25

Alineamiento de la puerta................... 26

Complete la instalación ....................... 26

ASSISTANCE OU SERVICE..................27

SÉCURITÉ DU RÉFRIGÉRATEUR..........27

EXIGENCES D’INSTALLATION ........... 28

Outillage et pièces................................28

Dimensions du produit..........................28

Exigences d'emplacement ................... 30

Spécifications électriques......................31

Spécifications de

l’alimentation en eau ............................. 31

INSTRUCTIONS D’INSTALLATION ..... 32

Déballage du réfrigérateur ................. 32

Panneaux de porte personnalisés....... 32

Raccordement de

la canalisation d'eau............................. 35

Brancher le réfrigérateur...................... 38

Préparer le système d'eau.................... 38

Nivellement et

fermeture de la porte ........................... 38

Alignement des portes.......................... 39

Achever l’installation............................. 39

W10399692B

Assistance or Service

If You Have Questions

If you have questions about operating, cleaning or maintaining

your refrigerator, see the Use & Care Guide.

If You Need Service

Maintain the quality built into your refrigerator by calling Sears

Parts & Repair at 18004MYHOME

Keep this book and your sales slip together for future

reference. You must provide proof of purchase or installation

date for in-warranty service.

Write down the following information about your appliance to

help you obtain assistance or service if you ever need it. You will

need to know your complete model number and serial number.

You can find this information on the model and serial number

label, located on the inside wall of the refrigerator

compartment.

Dealer name____________________________________________

Serial number ___________________________________________

Address________________________________________________

Phone number __________________________________________

Model number 106. ______________________________________

Purchase date___________________________________________

REFRIGERATOR SAFETY

INSTALLATION REQUIREMENTS

Tools and Parts

IMPORTANT:

■ Observe all governing codes and ordinances.

■ Installer: Leave Installation Instructions with homeowner.

■ Homeowner: Keep Installation Instructions for future

reference and for the local electrical inspector’s use.

■ Keep cardboard shipping piece or plywood under

refrigerator until it is installed in the operating position.

■ Comply with installation specifications and dimensions.

■ Remove any moldings or decorative panels from kitchen

cabinets that would not allow access to the refrigerator for

service.

■ Contact a qualified electrical installer.

You can be killed or seriously injured if you don't immediately

You

can be killed or seriously injured if you don't

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”

These words mean:

follow instructions.

instructions.

DANGER

WARNING

State of California Proposition 65 Warnings:

WARNING: This product contains one or more chemicals known to the State of California to cause cancer.

WARNING: This product contains one or more chemicals known to the State of California to cause birth defects or other

reproductive harm.

TOOLS NEEDED (on some models):

Gather the required tools and parts before starting installation.

Read and follow the instructions provided with any tools listed

here.

PARTS NEEDED (on some models):

■ Your refrigerator dealer has a kit available with a ¹⁄₄"

(6.35 mm) saddle-type shutoff valve, a union, and copper

tubing.

■ Or you can purchase a ¹⁄₄" (6.35 mm) copper tubing with

shutoff valve and a ¹⁄₄" (6.35 mm) compression fitting

(coupling).

■ Depending on water line connections, you may also need a

¹⁄₄" (6.35 mm) nut and ¹⁄₄" (6.35 mm) ferrule.

Product Dimensions

Top View

*Dimension may vary based on style of door handle.

The depth for the largest available handle is listed.

Front View

■ Cordless drill

■ ¹⁄₄" Nut driver

and drill bit

■ Flat-blade

screwdriver

■ ⁵⁄₁₆" or adjustable wrench

■ ⁷⁄₁₆" and ¹⁄₂" Open-end wrenches

■ Two adjustable wrenches

■ ³⁄₈" and ¹⁄₂" Socket wrenches

Door

Style

Depth

Flat 27¹⁄₂"

(69.8 cm)

2⁵⁄₈"(6.5cm)

maximum*

30" (76.3 cm)

maximum*

Curved 28⁵⁄₈"

(72.5 cm)

2⁵⁄₈"

(6.5 cm)

31¹⁄₈"

(79.1 cm)

35¹⁄₂"

(90.0 cm)

23⁷⁄₈"

(60.4 cm)

15³⁄₈"

(38.9 cm)

20"

(50.8 cm)

⁵⁄₈"

(1.6 cm)

Model Size Height A

69" 65³⁄₄" (166.9 cm)

72" 68¹⁄₈" (172.9 cm)

35³⁄₄"

(90.8 cm)

¹⁄₄"

(8.2 cm)

Side View

■ Height dimensions are shown with the leveling legs extended

to the minimum height of ¹⁄₄" (6.35 mm) below the

refrigerator.

NOTE: When leveling legs are fully extended to 1" (25 mm)

below the refrigerator, add ³⁄₄" (19 mm) to the height

dimensions.

■ The power cord is 61¹⁄₄" (155.6 cm) long.

■ The water line attached to the back of the refrigerator is

78" (198.1 cm) long.

Opening Dimensions

■ Height dimensions are shown with the leveling legs extended

to the minimum height of ¹⁄₄" (6.35 mm) below the

refrigerator.

NOTE: When leveling legs are fully extended to 1" (25 mm)

below the refrigerator, add ³⁄₄" (19 mm) to the height

dimensions.

■ In the following graphic, “A” represents the opening height

required for standard cabinets. For full-overlay cabinet

doors with a trim kit, add ¹⁄₈" (0.3 cm).

■ In the following graphic, “B” represents the distance needed

to fully open the freezer door and “C” represents the

distance needed to fully open the refrigerator door.

*Dimension may vary based on style of door handle.

The width for the largest available handle is listed.

Model Size Height A Height B Height C

69" 68⁷⁄₈"

(174.8 cm)

68⁷⁄₈"

(174.9 cm)

68¹⁄₂"

(174.2 cm)

72" 71¹⁄₄"

(180.8 cm)

71¹⁄₄"

(180.9 cm)

71"

(180.2 cm)

21³⁄₄"

(55.1 cm)

61¹⁄₄"

(155.6 cm)

3¹⁄₄" (8.2 cm)

Model Size

and

Door Style

Height

Width

69"

Flat

69"

(175.3 cm)

13⁵⁄₈"

(34.5 cm)

maximum*

18¹⁄₈"

(46.0 cm)

maximum*

72"

Flat

72"

(182.9 cm)

13⁵⁄₈"

(34.5 cm)

maximum*

18¹⁄₈"

(46.0 cm)

maximum*

69"

Curved

69"

(175.3 cm)

13³⁄₄"

(34.9 cm)

18³⁄₈"

(46.4 cm)

72"

Curved

72"

(182.9 cm)

13³⁄₄"

(34.9 cm)

18³⁄₈"

(46.4 cm)

36"

(91.4 cm)

Door Swing Dimensions

■ Location must permit doors to open to a minimum of 165°.

■ In the following graphic, “A” represents the distance needed

to fully open the freezer door and “B” represents the

distance needed to fully open the refrigerator door.

*Dimension may vary based on style of door handle.

The width for the largest available handle is listed.

Location Requirements

NOTES:

■ The cabinet depth refrigerator can be installed into a

recessed opening, at the end of cabinets or as a

freestanding refrigerator.

■ If you are installing the refrigerator to fit flush with the front

of the base cabinets, all shoe molding and baseboards must

be removed from the rear of the refrigerator opening. Allow

for 1" (2.54 cm) of space behind the refrigerator.

■ Location should permit doors to open fully. See the “Door

Swing Dimensions” section.

■ This refrigerator is intended for use in a location where the

temperature ranges from a minimum of 55°F (13°C) to a

maximum of 110°F (43°C). The preferred room temperature

range for optimum performance, which reduces electricity

usage and provides superior cooling, is between 60°F (15°C)

and 90°F (32°C). It is recommended that you do not install

the refrigerator near a heat source, such as an oven or

radiator.

■ Floor must support refrigerator weight (more than 600 lbs

[272 kg], door panels and contents).

Electrical Requirements

Before you move your refrigerator into its final location, it is

important to make sure you have the proper electrical

connection.

Recommended Grounding Method

A 115 volt, 60 Hz, AC only 15- or 20-amp fused, grounded

electrical supply is required. It is recommended that a separate

circuit serving only your refrigerator be provided. Use an outlet

that cannot be turned off by a switch. Do not use an

extension cord.

IMPORTANT: If this product is connected to a GFCI

(Ground Fault Circuit Interrupter) protected outlet, nuisance

tripping of the power supply may occur, resulting in loss of

cooling. Food quality and flavor may be affected. If nuisance

tripping has occurred, and if the condition of the food appears

poor, dispose of it.

NOTE: Before performing any type of installation, cleaning, or

removing a light bulb, turn the control (Thermostat, Refrigerator

or Freezer Control depending on the model) to OFF and then

disconnect the refrigerator from the electrical source. When you

are finished, reconnect the refrigerator to the electrical source

and reset the control (Thermostat, Refrigerator or Freezer

Control depending on the model) to the desired setting.

Dimension Flat Doors Curved Doors

A 13⁵⁄₈" (34.5 cm)

maximum*

13³⁄₄" (34.9 cm)

B 18¹⁄₈" (46.0 cm)

maximum*

18³⁄₈" (46.4 cm)

C 2³⁄₄" (6.7 cm)

maximum*

3³⁄₄" (9.4 cm)

D ¹⁄₈" (0.2 cm) 1¹⁄₄" (2.9 cm)

¹⁄₄" (104.5 cm)

45⁷⁄₈" (116.4 cm)

90˚

165˚

WARNING

Explosion Hazard

Keep flammable materials and vapors, such as

gasoline, away from refrigerator.

Failure to do so can result in death, explosion, or fire.

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

WARNING

Water Supply Requirements

Gather the required tools and parts before starting installation.

Read and follow the instructions provided with any tools listed

here.

TOOLS NEEDED:

NOTE: Your refrigerator dealer has a kit available with a ¹⁄₄"

(6.35 mm) saddle-type shutoff valve, a union, and copper

tubing. Before purchasing, make sure a saddle-type valve

complies with your local plumbing codes. Do not use a

piercing-type or ³⁄₁₆" (4.76 mm) saddle valve which reduces

water flow and clogs more easily.

IMPORTANT:

■ All installations must meet local plumbing code

requirements.

■ Use copper tubing and check for leaks. Install copper tubing

only in areas where the household temperatures will remain

above freezing.

Water Pressure

A cold water supply with water pressure of between 30 and

120 psi (207 and 827 kPa) is required to operate the water

dispenser and ice maker. If you have questions about your water

pressure, call a licensed, qualified plumber.

Reverse Osmosis Water Supply

IMPORTANT: The pressure of the water supply coming out of a

reverse osmosis system going to the water inlet valve of the

refrigerator needs to be between 30 and 120 psi (207 and

827 kPa).

If a reverse osmosis water filtration system is connected to your

cold water supply, the water pressure to the reverse osmosis

system needs to be a minimum of 40 to 60 psi (276 to 414 kPa).

If the water pressure to the reverse osmosis system is less than

40 to 60 psi (276 to 414 kPa):

■ Check to see whether the sediment filter in the reverse

osmosis system is blocked. Replace the filter if necessary.

■ Allow the storage tank on the reverse osmosis system to refill

after heavy usage.

■ If your refrigerator has a water filter, it may further reduce

the water pressure when used in conjunction with a reverse

osmosis system. Remove the water filter. See “Water

Filtration System” in the Use & Care Guide.

If you have questions about your water pressure, call a licensed,

qualified plumber.

INSTALLATION

INSTRUCTIONS

Unpack the Refrigerator

Remove the Packaging

Dispose of/recycle all packaging materials. Do not use sharp

instruments, rubbing alcohol, flammable fluids, or abrasive

cleaners to remove tape or glue. These products can damage

the surface of your refrigerator.

IMPORTANT:

■ Use ¹⁄₂" socket wrench to remove skids (socket extension is

recommended).

■ All four leveling legs must contact the floor to support and

stabilize the full weight of the refrigerator.

Clean Before Using

After you remove all of the package materials, clean the inside

of your refrigerator before using it. See the cleaning instructions

in the Use & Care Guide or User Instructions.

■ Flat-blade screwdriver

■ ⁷⁄₁₆" and ¹⁄₂" Open-end or two

adjustable wrenches

■ ¹⁄₄" Nut driver

■ ¹⁄₄" Drill bit

■ Cordless drill

WARNING

Excessive Weight Hazard

Use two or more people to move and install

refrigerator.

Failure to do so can result in back or other injury.

When Moving Your Refrigerator:

Your refrigerator is heavy. When moving the refrigerator for

cleaning or service, be sure to cover the floor with

cardboard or hardboard to avoid floor damage. Always pull

the refrigerator straight out when moving it. Do not wiggle or

“walk” the refrigerator when trying to move it, as floor

damage could occur.

Important information to know about glass shelves

and covers:

Do not clean glass shelves or covers with warm water when

they are cold. Shelves and covers may break if exposed to

sudden temperature changes or impact, such as bumping.

Tempered glass is designed to shatter into many small,

pebble-size pieces. This is normal. Glass shelves and covers

are heavy. Use both hands when removing them to avoid

dropping.

Custom Door Panels (on some models)

Custom door panels allow you to blend the exterior of your

refrigerator into the overall kitchen décor. If you plan to install

custom wood panels, you will need to create the panels yourself

or consult a qualified cabinetmaker or carpenter. Follow these

panel dimension and placement instructions to be sure that the

custom panels will fit properly.

The custom panels must have backer panels attached in order

to mount them to the refrigerator. It is most common to work

with three panels, as shown in the following graphic: a ³⁄₄"

(19.05 mm) decorative panel, a ¹⁄₁₆" (1.59 mm) spacer panel or

spacer strips, and a ¹⁄₄" (6.35 mm) backer panel.

NOTE: You can also work with two panels, as shown in the

following graphic: a ³⁄₄" (19.05 mm) decorative panel routed

with a ¹⁄₁₆" (1.59 mm) cutout, and a separate ¹⁄₄" (6.35 mm)

backer panel.

Weight Limits

IMPORTANT: Panels weighing more than the recommended

weight may cause damage to your refrigerator.

■ The weight of the freezer door panel(s) cannot exceed

25 lbs (11.3 kg).

■ The weight of the refrigerator door panel(s) cannot exceed

41 lbs (18.6 kg).

To minimize panel weight, you may use 2" (5.08 cm) spacer

strips around the perimeter in place of solid full-sheet spacer

panels. The spacer strips must be set in at least 1" (2.54 cm)

from the top, bottom and side edges of the backer panel. If you

use spacer strips, it is also recommended that you use two

horizontallycentered 2" (5.08 cm) strips for added support.

Decorative Panel Dimensions

NOTE: The dashed line represents the placement of the

dispenser frame.

Decorative Panel

Spacer Panel

Backer Panel

/4"

(19.05 mm)

/₁₆"

(1.59 mm)

/4"

(6.35 mm)

1" minimum

(2.54 cm)

Door

Trim

Spacer Panel

/₁₆"

(1.59 mm)

Decorative Panel

Backer Panel

Decorative Panel

Backer Panel

/16"

(17.46 mm)

/4"

(6.35 mm)

1" minimum

(2.54 cm)

/16"

(1.59 mm)

Door

Trim

/₁₆"

(1.59 mm)

Decorative

Panel

Backer Panel

/₄"

(19.05 mm)

Dimension Height/Width

A 19³⁄₈" (49.2 cm)

B 31³⁄₄" (80.6 cm)

C 68³⁄₁₆" (173.2 cm)

D 15³⁄₈" (39.1 cm)

E 20" (50.8 cm)

F 17¹⁄₁₆" (43.3 cm)

G 11¹⁵⁄₃₂" (29.1 cm)

Freezer

Door Panel

(Non-Dispenser)

Refrigerator

Door Panel

Freezer

Door Panel

(Dispenser)

Dispenser

cutout is

centered

left-to-right

Backer and Spacer Panel Dimensions

NOTE: The dashed lines represent the placement of the backer

and spacer panels on the decorative panels. Backer and spacer

panels should be centered vertically and horizontally.

Install the Door Panels

NOTE: In the graphics throughout this section, dark gray

represents the door trim and light gray represents the door

panel.

1. Remove the upper trim from the top of the freezer door.

2. Remove the side trim from each side of the freezer door.

Dimension Backer Panel Spacer Panel

A 19" (48.3 cm) 18³⁄₈" (46.7 cm)

B 31¹⁵⁄₃₂" (79.9 cm) 30³⁄₄" (78.1 cm)

C 67²⁹⁄₃₂" (172.5 cm) 66⁹⁄₁₆" (169.1 cm)

D 14⁷⁄₈" (37.8 cm) 14¹⁄₄" (36.2 cm)

E 19¹⁄₂" (49.6 cm) 18⁷⁄₈" (47.9 cm)

D D

3. Align the bottom edge of the door panel with the lower trim

on the bottom of the freezer door. Center the panel on the

freezer door.

4. Reseat each side trim, making sure the trim clip slides inside

the corner of the lower trim.

5. With the side trims properly seated in the lower trim, slide

each trim into the door panel groove.

6. Align the upper trim with the trim clips at the top of each

side trim.

7. Slide the upper trim into the door panel groove by applying

firm downward pressure. Be sure that the grooves on the

upper trim are properly aligned with the rivets on the door

panel.

8. When fully seated, the upper trim should be nearly flush

with the top of the freezer door, completely covering both

side trim clips.

9. Repeat the previous steps to install the refrigerator door

panel.

A. Trim clip

Install Dispenser Frame (dispenser models only)

After installing the custom door panels, snap the dispenser

frame onto the freezer door as shown.

Connect Water Supply

Read all directions before you begin.

IMPORTANT:

■ Plumbing shall be installed in accordance with the

International Plumbing Code and any local codes and

ordinances.

■ The gray water tubing on the back of the refrigerator (which

is used to connect to the household water line) is a PEX

(crosslinked polyethylene) tube. Copper and PEX tubing

connections from the household water line to the refrigerator

are acceptable, and will help avoid offtaste or odor in your

ice or water. Check for leaks.

■ Install tubing only in areas where temperatures will remain

above freezing.

TOOLS NEEDED:

Gather the required tools and parts before starting installation.

■ Flat-blade screwdriver

■ ⁷⁄₁₆" and ¹⁄₂" open-end wrenches or two adjustable wrenches

■ ¹⁄₄" nut driver

Connect to Water Line

IMPORTANT: If you turn the refrigerator on before the water

line is connected, turn the ice maker OFF.

Style 1 (Recommended)

1. Unplug refrigerator or disconnect power.

2. Turn OFF main water supply. Turn ON nearest faucet long

enough to clear line of water.

3. Use a quarter-turn shutoff valve or the equivalent, served by

a ¹⁄₂" copper household supply line.

NOTE: To allow sufficient water flow to the refrigerator, a

minimum ¹⁄₂" size copper household supply line is

recommended.

4. Now you are ready to connect the copper tubing to the

shutoff valve. Use ¹⁄₄" (6.35 mm) OD soft copper tubing to

connect the shutoff valve and the refrigerator.

■ Ensure that you have the proper length needed for the

job. Be sure both ends of the copper tubing are cut

square.

■ Slip compression sleeve and compression nut onto

copper tubing as shown. Insert end of tubing into outlet

end squarely as far as it will go. Screw compression nut

onto outlet end with adjustable wrench. Do not

overtighten.

5. Place the free end of the tubing into a container or sink, and

turn on main water supply to flush out tubing until water is

clear. Turn off shutoff valve on the water pipe.

NOTE: Always drain the water line before making the final

connection to the inlet of the water valve, to avoid possible

water valve malfunction.

6. Bend the copper tubing to meet the water line inlet, which is

located on the back of the refrigerator cabinet as shown.

Leave a coil of copper tubing to allow the refrigerator to be

pulled out of the cabinet or away from the wall for service.

Style 2

1. Unplug refrigerator or disconnect power.

2. Turn OFF main water supply. Turn ON nearest faucet long

enough to clear line of water.

3. Locate a

¹⁄₂" (1.27 cm) to 1¹⁄₄" (3.18 cm) vertical cold water

pipe near the refrigerator.

IMPORTANT:

■ Make sure it is a cold water pipe.

■ Horizontal pipe will work, but drill on the top side of the

pipe, not the bottom. This will help keep water away

from the drill and normal sediment from collecting in the

valve.

A. Bulb

B. Nut

C. Copper tubing (to refrigerator)

D. Household supply line (½" minimum)

A. Compression sleeve

B. Compression nut

C. Copper tubing

B CA

4. Determine the length of copper tubing you need. Measure

from the connection on the lower rear corner of refrigerator

to the water pipe. Add 7 ft (2.1 m) to allow for cleaning. Use

¹⁄₄" (6.35 mm) O.D. (outside diameter) copper tubing. Be

sure both ends of copper tubing are cut square.

5. Using a cordless drill, drill a ¹⁄₄" (6.35 mm) hole in the cold

water pipe you have selected.

6. Fasten the shutoff valve to the cold water pipe with the pipe

clamp. Be sure the outlet end is solidly in the ¹⁄₄" (6.35 mm)

drilled hole in the water pipe and that the washer is under

the pipe clamp. Tighten the packing nut. Tighten the pipe

clamp screws slowly and evenly so the washer makes a

watertight seal. Do not overtighten, or you may crush the

copper tubing.

7. Slip the compression sleeve and compression nut on the

copper tubing as shown. Insert the end of the tubing into the

outlet end squarely as far as it will go. Screw the

compression nut onto outlet end with adjustable wrench. Do

not overtighten.

8. Place the free end of the tubing in a container or sink, and

turn ON the main water supply. Flush the tubing until water

is clear. Turn OFF the shutoff valve on the water pipe. Coil

the copper tubing.

Connect to Refrigerator

Style 1

1. Unplug refrigerator or disconnect power.

2. Remove and discard the short, black plastic part from the

end of the water line inlet.

3. Thread the nut onto the end of the tubing. Tighten the nut by

hand. Then tighten it with a wrench two more turns. Do not

overtighten.

NOTE: To avoid rattling, be sure the copper tubing does not

touch the cabinet’s side wall or other parts inside the

cabinet.

4. Install the water supply tube clamp around the water supply

line to reduce strain on the coupling.

5. Turn shutoff valve ON.

6. Check for leaks. Tighten any connections (including

connections at the valve) or nuts that leak.

Style 2

1. Unplug refrigerator or disconnect power.

2. Remove and discard the plastic part that is attached to the

inlet of the water valve.

3. Attach the copper tube to the valve inlet using a

compression nut and sleeve as shown. Tighten the

compression nut. Do not overtighten.

4. Use the tube clamp on the back of the refrigerator to secure

the tubing to the refrigerator as shown. This will help avoid

damage to the tubing when the refrigerator is pushed back

against the wall.

5. Turn shutoff valve ON.

6. Check for leaks. Tighten any connections (including

connections at the valve) or nuts that leak.

7. On some models, the ice maker is equipped with a built-in

water strainer. If your water conditions require a second

water strainer, install it in the ¹⁄₄" (6.35 mm) water line at

either tube connection. Obtain a water strainer from your

nearest appliance dealer.

Style 3

1. Unplug refrigerator or disconnect power.

2. Remove and discard the black nylon plug from the gray

water tube on the rear of the refrigerator.

3. If the gray water tube supplied with the refrigerator is not

long enough, a ¹⁄₄" x ¹⁄₄" (6.35 mm x 6.35 mm) coupling is

needed in order to connect the water tubing to an existing

household water line. Thread the provided nut onto the

coupling on the end of the copper tubing.

A. Cold water pipe

B. Pipe clamp

C. Copper tubing

D. Compression nut

E. Compression sleeve

F. Shutoff valve

G. Packing nut

A. Household water line

B. Nut (purchased)

C. Ferrule (purchased)

D. Refrigerator water tubing

DEF

A B C

A. Tube clamp

B. Tube clamp screw

C. Copper tubing

D. Compression nut

E. Valve inlet

NOTE: Tighten the nut by hand. Then tighten it with a

wrench two more turns. Do not overtighten.

4. Turn shutoff valve ON.

5. Check for leaks. Tighten any nuts or connections (including

connections at the valve) that leak.

Plug in Refrigerator

1. Plug into a grounded 3 prong outlet.

Prepare the Water System

Please read before using the water system.

Immediately after installation, follow the steps below to make

sure that the water system is properly cleaned.

1. Open the freezer door and turn off the ice maker. The On/

Off switch can only be accessed when the ice storage bin

has been removed. The switch is located on the freezer door,

on the left side of the wall that surrounds the ice storage bin.

Move the switch to the OFF (right) setting.

2. Make sure the water filter is properly installed.

3. Flush the water system. Use a sturdy container to depress

and hold the water dispenser lever for 5 seconds, then

release it for 5 seconds. Repeat until water begins to flow.

Once water begins to flow, continue depressing and

releasing the dispenser lever (5 seconds on, 5 seconds off)

until a total of 3 gal. (12 L) has been dispensed. This will

flush air from the filter and water dispensing system, and

prepare the water filter for use. Additional flushing may be

required in some households. As air is cleared from the

system, water may spurt out of the dispenser.

4. Open the freezer door and turn on the ice maker. Move the

switch to the ON (left) position. See the Use & Care Guide

or User Instructions for further instructions on the operation

of your ice maker.

■ Allow 24 hours to produce the first batch of ice.

■ Discard the first three batches of ice produced.

■ Depending on your model, you may want to select the

maximum ice feature to increase the production of ice.

Leveling and Door Closing

Your refrigerator has two adjustable front feet — one on the

right and one on the left. In most cases, the refrigerator should

be steady when both feet are touching the floor. If your

refrigerator seems unsteady or if you want the doors to close

more easily, adjust the refrigerator's tilt using the instructions

below:

1. Move the refrigerator into its final location. Open both

doors to 90°. Remove the base grille by removing the two

screws, then pulling out on the outside corners.

NOTE: The doors must only be opened to 90°. If they are

opened all the way, the base grille will not come off.

2. The two leveling feet are located on the brackets on each

side of the product.

A. Refrigerator water tubing

B. Nut (provided)

C. Bulb

D. Coupling (purchased)

E. Ferrule (purchased)

F. Nut (purchased)

G. Household water line

A B C D E F G

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

WARNING

Do not use with water that is microbiologically unsafe or

of unknown quality without adequate disinfection before

or after the system. Systems certified for cyst reduction

may be used on disinfected waters that may contain

filterable cysts.

A. Bottom hinge

B. Leveler bracket

C. Leveling foot

Raise

Lower

NOTE: Having someone push against the top of the refrigerator

takes some weight off the leveling feet. This makes it easier to

make adjustments.

3. Use a ¹⁄₄" open-ended or adjustable wrench to adjust the

leveling feet. Turn the leveling foot to the left to raise that

side of the product, or turn it to the right to lower that side of

the product.

4. Open both doors again and check that they close as easily

as you like. If not, tilt the refrigerator slightly more to the

rear by turning the leveling feet to the left. It may take

several more turns, and you should turn both leveling feet

the same amount.

NOTE: Whenever you need to move the refrigerator, turn the

leveling feet to the right until they are no longer touching the

ground. This will allow the refrigerator to roll more easily.

Door Alignment

A refrigerator that is not level from side-to-side may appear to

have doors that are not properly aligned. If the doors appear

this way, use the instructions in the previous section to check the

leveling.

The doors are designed to be slightly different heights when the

refrigerator is empty, in order to account for the weight of food

that will be placed on the doors. If the doors are still not aligned

after checking the leveling and loading the refrigerator with

food, follow the steps below to adjust the door alignment.

1. If necessary, open both doors to 90° and remove the base

grille.

2. Locate the alignment screw on the bottom hinge of the

refrigerator door.

3. Use a ⁵⁄₁₆" open-ended or adjustable wrench to turn the

screw. To raise the refrigerator door, turn the screw to the

right. To lower the door, turn the screw to the left.

4. Check that the doors are even at the top. If necessary,

continue to turn the alignment screw until the doors are

aligned.

5. Open both doors to 90°. Replace the base grille.

Complete Installation

1. Turn water supply line valve to “Open” position.

2. Turn refrigerator switch to ON position. Wait a few minutes.

Check water line connections for leaks.

3. Set refrigerator and freezer compartment controls to the

midpoint setting. Check that the compressor is operating

properly and that all lights are working.

4. Flush water system before using. See “Prepare the Water

System.”

NOTE: If construction will continue after refrigerator has been

installed, set controls to OFF.

If Refrigerator Does Not Operate

■ Check that the circuit breaker is not tripped or household

fuse blown.

■ Check that the power supply cord is plugged into a

grounded 3 prong outlet.

■ See “Problem Solver” or “Troubleshooting” in the Use &

Care Guide or User Instructions.

A. Alignment screw

Raise

Lower

INSTRUCCIONES DE INSTALACIÓN

Refrigerador de dos puertas con profundidad de mostrador

Ayuda o Servicio Técnico

Si tiene preguntas

Si usted tiene preguntas acerca del funcionamiento, la limpieza

o el mantenimiento de su refrigerador, vea el Manual de uso y

cuidado.

Si necesita servicio

Mantenga la calidad de su refrigerador llamando a Piezas y

Reparaciones de Sears al 18004MYHOME

Guarde este libro y su comprobante de compra juntos para

referencia futura. Usted deberá proporcionar evidencia de la

compra o una fecha de instalación para obtener servicio bajo

la garantía.

Escriba la siguiente información acerca de su electrodoméstico

para ayudarle a obtener asistencia o servicio técnico si alguna

vez llegara a necesitarlo. Deberá tener a mano el número

completo del modelo y de la serie. Puede encontrar esta

información en la etiqueta con el número de modelo y de serie

que está ubicada en la pared interior del compartimiento del

refrigerador.

Nombre del distribuidor ___________________________________

Número de serie_________________________________________

Dirección_______________________________________________

Número de teléfono ______________________________________

Número del modelo 106. __________________________________

Fecha de compra ________________________________________

SEGURIDAD DEL REFRIGERADOR

Si no sigue las instrucciones de inmediato, usted puede

morir o sufrir una lesión grave.

Si no sigue las instrucciones, usted puede morir o sufrir

una lesión grave.

Todos los mensajes de seguridad le dirán el peligro potencial, le dirán cómo reducir las posibilidades de sufrir una lesión y lo que

puede suceder si no se siguen las instrucciones.

Su seguridad y la seguridad de los demás es muy importante.

Hemos incluido muchos mensajes importantes de seguridad en este manual y en su electrodoméstico. Lea y obedezca siempre

todos los mensajes de seguridad.

ADVERTENCIA

PELIGRO

Este es el símbolo de advertencia de seguridad.

Este símbolo le llama la atención sobre peligros potenciales que pueden ocasionar la muerte o una lesión a

usted y a los demás.

Todos los mensajes de seguridad irán a continuación del símbolo de advertencia de seguridad y de la palabra

“PELIGRO” o “ADVERTENCIA”. Estas palabras significan:

Advertencias de la Proposición 65 del estado de California:

ADVERTENCIA: Este producto contiene una o más sustancias químicas identificadas por el estado de California como

causantes de cáncer.

ADVERTENCIA: Este producto contiene una o más sustancias químicas identificadas por el estado de California como

causantes de defectos congénitos o algún otro tipo de daños en la función reproductora.

REQUISITOS DE INSTALACIÓN

Piezas y herramientas

IMPORTANTE:

■ Observe todos los códigos y reglamentos aplicables.

■ Instalador: Deje las instrucciones de instalación con el

propietario.

■ Propietario: Guarde las instrucciones de instalación para

referencia futura y para que puedan ser usadas por el

inspector eléctrico local.

■ Mantenga un tramo de cartón de empaque o de madera

contrachapada debajo del refrigerador hasta que lo instale

en su ubicación final.

■ Cumpla con las especificaciones y medidas de instalación.

■ Saque todas las molduras o paneles decorativos de los

armarios de la cocina que impidan el acceso al refrigerador

para darle servicio.

■ Contacte a un instalador electricista calificado.

HERRAMIENTAS NECESARIAS (en algunos modelos):

Reúna las herramientas y piezas necesarias antes de comenzar

la instalación. Lea y siga las instrucciones provistas con

cualquiera de las herramientas enlistadas aquí.

PIEZAS NECESARIAS (en algunos modelos):

■ El distribuidor de su refrigerador tiene un juego disponible

de válvula de cierre tipo montura de ¼" (6,35 mm), una

unión y tubería de cobre.

■ O usted puede comprar una tubería de cobre de ¼"

(6,35 mm) con válvula de cierre y un accesorio de

compresión (acoplamiento) de ¼" (6,35 mm).

■ Dependiendo de las conexiones de la línea de agua, usted

también puede necesitar una tuerca de ¼" (6,35 mm) y una

férula de ¼" (6,35 mm).

Medidas del producto

Vista superior

*Las dimensiones pueden variar según el estilo de la manija de

la puerta. Se indica la profundidad para la manija más

grande que hay disponible.

■ Taladro

inalámbrico

■ Llave para tuercas

de ¹⁄₄"y broca

■ Destornillador de

hoja plana

■ Llave de ⁵⁄₁₆" o llave ajustable

■ Llaves de boca de ⁷⁄₁₆"y¹⁄₂"

■ Dos llaves ajustables

■ Llaves de cubo de ³⁄₈"y¹⁄₂"

Estilo de

puerta

Profundidad

Plana 27¹⁄₂"

(69,8 cm)

2⁵⁄₈"(6,5cm)

máxima*

30" (76,3 cm)

máxima*

Curva 28⁵⁄₈"

(72,5 cm)

2⁵⁄₈"

(6,5 cm)

31¹⁄₈"

(79,1 cm)

35¹⁄₂"

(90,0 cm)

23⁷⁄₈"

(60,4 cm)

15³⁄₈"

(38,9 cm)

20"

(50,8 cm)

⁵⁄₈"

(1,6 cm)

Vista frontal

Vista lateral

■ Las medidas de altura indicadas consideran las patas

niveladoras extendidas como mínimo ¼" (6,35 mm) por

debajo del refrigerador.

NOTA: Si las patas niveladoras están totalmente extendidas

1" (25 mm) por debajo del refrigerador, agregue ³⁄₄"

(19 mm) a las medidas de altura.

■ El cable de suministro de energía es de 61¹⁄₄" (155,6 cm) de

largo.

■ La línea de agua ajustada a la parte posterior del

refrigerador es de 78" (198,1 cm) de largo.

Medidas de abertura

■ Las medidas de altura indicadas consideran las patas

niveladoras extendidas como mínimo ¼" (6,35 mm) por

debajo del refrigerador.

NOTA: Si las patas niveladoras están totalmente extendidas

1" (25 mm) por debajo del refrigerador, agregue ³⁄₄"

(19 mm) a las medidas de altura.

■ En la ilustración a continuación, “A” representa la altura de

abertura necesaria para los armarios estándar. Para las

puertas de armarios completamente recubiertos con juego

de molduras, agregue ¹⁄₈" (0,3 cm).

Tamaño del modelo Altura A

69" 65³⁄₄" (166,9 cm)

72" 68¹⁄₈" (172,9 cm)

35³⁄₄"

(90,8 cm)

¹⁄₄"

(8,2 cm)

Tamaño del

modelo

Altura A Altura B Altura C

69" 68⁷⁄₈"

(174,8 cm)

68⁷⁄₈"

(174,9 cm)

68¹⁄₂"

(174,2 cm)

72" 71¹⁄₄"

(180,8 cm)

71¹⁄₄"

(180,9 cm)

71"

(180,2 cm)

21³⁄₄"

(55,1 cm)

61¹⁄₄"

(155,6 cm)

3¹⁄₄" (8,2 cm)

■ En la ilustración a continuación, “B” representa la distancia

necesaria para abrir por completo la puerta del congelador

y “C” representa la distancia necesaria para abrir por

completo la puerta del refrigerador.

*Las dimensiones pueden variar según el estilo de la manija de

la puerta. Se indica el ancho para la manija más grande que

hay disponible.

Medidas de oscilación de las puertas

■ La ubicación debe permitir que las puertas se abran a un

mínimo de 165°.

■ En la ilustración a continuación, “A” representa la distancia

necesaria para abrir por completo la puerta del congelador

y “B” representa la distancia necesaria para abrir por

completo la puerta del refrigerador.

*Las dimensiones pueden variar según el estilo de la manija de

la puerta. Se indica el ancho para la manija más grande que

hay disponible.

Requisitos de ubicación

NOTAS:

■ El refrigerador con profundidad de armario puede

instalarse empotrado, al final de los armarios o por

separado.

■ Si va a instalar el refrigerador para estar alineado con el

frente de los armarios de base, se deben quitar todas las

molduras y los zócalos de la parte poserior de la abertura

del refrigerador. Deje un espacio de 1" (2,54 cm) detrás del

refrigerador.

■ La ubicación deberá permitir que las puertas se abran

completamente. Vea la sección “Medidas de oscilación de

las puertas”.

Tamaño del

modelo y

estilo de puerta

Altura

Ancho

69"

Plana

69"

(175,3 cm)

13⁵⁄₈"

(34,5 cm)

máximo*

18¹⁄₈"

(46,0 cm)

máximo*

72"

Plana

72"

(182,9 cm)

13⁵⁄₈"

(34,5 cm)

máximo*

18¹⁄₈"

(46,0 cm)

máximo*

69"

Curva

69"

(175,3 cm)

13³⁄₄"

(34,9 cm)

18³⁄₈"

(46,4 cm)

72"

Curva

72"

(182,9 cm)

13³⁄₄"

(34,9 cm)

18³⁄₈"

(46,4 cm)

36"

(91,4 cm)

Dimensión Puertas planas Puertas curvas

A 13⁵⁄₈" (34,5 cm)

máximo*

13³⁄₄" (34,9 cm)

B 18¹⁄₈" (46,0 cm)

máximo*

18³⁄₈" (46,4 cm)

C 2³⁄₄" (6,7 cm)

máximo*

3³⁄₄" (9,4 cm)

D ¹⁄₈" (0,2 cm) 1¹⁄₄" (2,9 cm)

¹⁄₄" (104,5 cm)

45⁷⁄₈" (116,4 cm)

90˚

165˚

ADVERTENCIA

Peligro de Explosión

Mantenga los materiales y vapores inflamables,

tales como gasolina, alejados del refrigerador.

No seguir esta instrucción puede ocasionar la muerte,

explosión, o incendio.

■ Este refrigerador ha sido diseñado para usarse en un lugar

en donde los rangos de temperatura varíen entre un mínimo

de 55°F (13°C) y un máximo de 110°F (43°C). Para un

óptimo rendimiento, el rango preferido de temperatura de

la habitación (que reduce el uso de electricidad y provee un

enfriamiento superior) es entre 60°F (15°C) y 90°F (32°C).

No se recomienda instalar el refrigerador cerca de una

fuente de calor, como puede ser un horno o un radiador.

■ El piso debe soportar el peso del refrigerador (más de

600 lbs [272 kg], los paneles de las puertas y el contenido).

Requisitos eléctricos

Antes de mover el refrigerador a su posición definitiva, es

importante asegurarse que Ud. tiene la conexión eléctrica

adecuada.

Método de conexión a tierra recomendado

Se requiere una fuente de energía eléctrica de 115 Voltios,

60 Hz., CA solamente y con fusibles de 15 ó 20 amperios,

conectada a tierra. Se recomienda que se use un circuito

separado sólo para su refrigerador. Use un tomacorriente que

no se puede apagar con un interruptor. No use un cable

eléctrico de extensión.

IMPORTANTE: Si este producto está conectado a un

tomacorriente protegido por GFCI (Ground Fault Circuit

Interrupter - Interruptor de circuito de falla eléctrica de puesta

a tierra), puede ocurrir un disparo molesto del suministro de

corriente, lo que resultará en la pérdida de refrigeración. Esto

puede afectar la calidad y el sabor de los alimentos. Si ha

ocurrido un disparo molesto, y el alimento aparenta estar en

malas condiciones, deshágase del mismo.

NOTA: Antes de realizar cualquier tipo de instalación, limpieza

o de quitar un foco de luz, ponga el control (del termostato, del

refrigerador o del congelador dependiendo del modelo) en la

posición OFF (Apagado) y luego desconecte el refrigerador de

la fuente de energía. Cuando Ud. haya terminado, reconecte el

refrigerador a la fuente de energía eléctrica y vuelva a poner el

control (del termostato, del refrigerador o del congelador

dependiendo del modelo) en la posición deseada.

Requisitos del suministro de agua

Reúna las herramientas y piezas necesarias antes de comenzar

la instalación. Lea y siga las instrucciones provistas con

cualquiera de las herramientas enlistadas aquí.

HERRAMIENTAS NECESARIAS:

NOTA: El distribuidor de su refrigerador tiene un juego

disponible con una válvula de cierre tipo montura de

¹⁄₄"

(6,35 mm), una unión y tubería de cobre. Antes de comprar,

asegúrese que la válvula tipo montura cumpla con los códigos

de plomería de su localidad. No use una válvula perforadora o

una válvula de montura de

³⁄₁₆" (4,76 mm) que reduce el flujo

de agua y se obstruye con más facilidad.

IMPORTANTE:

■ Todas las instalaciones deben hacerse de acuerdo a los

requerimientos locales de plomería.

■ Use tuberías de cobre y revise si hay fugas. Instale tubería

de cobre sólo en áreas donde la temperatura va a

permanecer por encima del punto de congelación.

Presión del agua

Se necesita un suministro de agua fría con presión de agua

entre 30 y 120 lbs/pulg2 (207 y 827 kPa) para hacer funcionar

el despachador de agua y la fábrica de hielo. Si usted tiene

preguntas acerca de la presión de agua, llame a un plomero

competente autorizado.

Suministro de agua de ósmosis inversa

IMPORTANTE: La presión del suministro de agua que sale de un

sistema de ósmosis inversa y va a la válvula de entrada de

agua del refrigerador necesitará ser entre 30 y 120 lbs/pulg2

(207 y 827 kPa).

Si se conecta un sistema de filtración de agua de ósmosis

inversa al suministro de agua fría, la presión de agua al sistema

de ósmosis inversa necesitará ser de un mínimo de 40 a

60 lbs/pulg2 (276 a 414 kPa).

Si la presión del agua del sistema de ósmosis inversa es menor

de 40 a 60 lbs/pulg2 (276 a 414 kPa):

■ Fíjese si el filtro de sedimentos en el sistema de ósmosis

inversa está bloqueado y reemplácelo si fuera necesario.

■ Deje que se vuelva a llenar el tanque de almacenaje del

sistema de ósmosis inversa después del uso intenso.

■ Si su refrigerador tiene un cartucho del filtro de agua, se

podrá reducir la presión aún más si se usa en conjunto con

un sistema de ósmosis inversa. Quite el cartucho del filtro de

agua. Vea “Sistema de filtración de agua” en el Manual de

uso y cuidado.

Si tiene preguntas acerca de la presión del agua, llame a un

plomero competente autorizado.

ADVERTENCIA

Peligro de Choque Eléctrico

Conecte a un contacto de pared de conexión a tierra de

3 terminales.

No quite la terminal de conexión a tierra.

No use un adaptador.

No use un cable eléctrico de extensión.

No seguir estas instrucciones puede ocasionar

la muerte, incendio o choque eléctrico.

■ Destornillador de hoja plana

■ Llaves de boca de ⁷⁄₁₆" y ¹⁄₂"

o dos llaves ajustables

■ Llave para tuercas de ¹⁄₄"

■ Broca de ¹⁄₄"

■ Taladro inalámbrico

INSTRUCCIONES DE INSTALACIÓN

Desempaque el refrigerador

Cómo quitar los materiales de empaque

Deshágase de todos los materiales de embalaje o recíclelos. No

use instrumentos filosos, alcohol para fricciones, líquidos

inflamables o productos de limpieza abrasivos para eliminar los

restos de cinta o goma. Estos productos pueden dañar la

superficie de su refrigerador.

IMPORTANTE:

■ Use una llave de cubo de ¹⁄₂" para quitar la plataforma (se

recomienda usar una extensión para llave de cubo).

■ Las cuatro patas niveladoras deberán tocar el piso para

soportar y estabilizar el peso total del refrigerador.

Cómo limpiar su refrigerador antes de usarlo

Una vez que usted haya quitado todos los materiales de

empaque, limpie el interior de su refrigerador antes de usarlo.

Vea las instrucciones de limpieza en el Manual de uso y

cuidado o las Instrucciones para el usuario.

Paneles para puerta a la medida

(en algunos modelos)

Los paneles de la puerta a la medida le permiten armonizar el

exterior de su refrigerador con la decoración de la cocina. Si va

a instalar paneles de madera a la medida, deberá hacerlos

usted mismo o consultar un carpintero o fabricante de gabinetes

calificado. Siga estas instrucciones para las medidas y la

ubicación de los paneles, para asegurarse de que los paneles a

la medida encajen adecuadamente.

Los paneles a la medida deben tener paneles de soporte

instalados para montarlos en el refrigerador. Lo más común es

trabajar con tres paneles, como se muestra en la siguiente

gráfica: un panel decorativo de ³⁄₄" (19,05 mm), un panel

espaciador de ¹⁄₁₆" (1,59 mm) o tiras espaciadoras, y un panel

de soporte de ¹⁄₄" (6,35 mm).

NOTA: También puede trabajar con dos paneles, como se

muestra en la ilustración siguiente: un panel decorativo de ³⁄₄"

(19,05 mm), contorneado con un recorte de ¹⁄₁₆" (1,59 mm), y un

panel de soporte de ¹⁄₄" (6,35 mm) por separado.

ADVERTENCIA

Peligro de Peso Excesivo

Use dos o más personas para mover e instalar

el refrigerador.

No seguir esta instrucción puede ocasionar una

lesión en la espalda u otro tipo de lesiones.

Cómo mover su refrigerador:

Su refrigerador es pesado. Cuando mueva el refrigerador

para limpiarlo o para darle servicio, cerciórese de cubrir

el piso con cartón o madera para evitar daños en el mismo.

Al mover el refrigerador, siempre tire directamente hacia

afuera. No menee el refrigerador de lado a lado ni lo haga

“caminar” cuando lo trate de mover ya que podría dañar

el piso.

Información importante para saber acerca de los estantes

y tapas de vidrio:

No limpie los estantes y tapas de vidrio con agua caliente

mientras están fríos. Los estantes y tapas pueden romperse

si se exponen a cambios bruscos de temperatura o impacto,

como sería un golpe brusco. El vidrio templado se ha

diseñado para hacerse añicos. Esto es normal. Los estantes

y tapas de vidrio son muy pesados. Use ambas manos al

sacarlos para evitar que se caigan.

Panel decorativo

Panel espaciador

Panel de

soporte

/4"

(19,05 mm)

/₁₆"

(1,59 mm)

/4"

(6,35 mm)

1" mínimo

(2,54 cm)

Panel de soporte

Panel decorativo

Moldura

de la

puerta

Panel espaciador

/₁₆"

(1,59 mm)

Moldura

de la

puerta

Panel decorativo

Panel de

soporte

/16"

(17,46 mm)

/4"

(6,35 mm)

1" mínimo

(2,54 cm)

/16"

(1,59 mm)

/₁₆"

(1,59 mm)

Panel

decorativo

Panel de soporte

/₄"

(19,05 mm)

Límites de peso

IMPORTANTE: Los paneles que pesan más de lo recomendado

pueden dañar su refrigerador.

■ El peso del (de los) panel(es) de la puerta del congelador no

debe sobrepasar las 25 lb (11,3 kg).

■ El peso del (de los) panel(es) de la puerta del refrigerador

no debe sobrepasar las 41 lb (18,6 kg).

Para minimizar el peso del panel, puede usar tiras espaciadoras

de 2" (5,08 cm) alrededor del perímetro en lugar de paneles

espaciadores de hoja plena macizos. Las tiras espaciadoras

deben fijarse a una distancia de al menos 1" (2,54 cm) de los

extremos superior, inferior y lateral del panel de soporte. Si usa

tiras espaciadoras, se recomienda también que use dos tiras de

2" (5,08 cm) centradas horizontalmente para proveer soporte

adicional.

Dimensiones del panel decorativo

NOTA: La línea de rayas representa la ubicación del marco del

despachador.

Dimensiones del panel de soporte y espaciador

NOTA: Las líneas de rayas representan la ubicación de los

paneles de soporte y espaciadores sobre los paneles

decorativos. Los paneles de soporte y espaciadores deberán

estar centrados vertical y horizontalmente.

Dimensión Altura/Ancho

A 19³⁄₈" (49,2 cm)

B 31³⁄₄" (80,6 cm)

C 68³⁄₁₆" (173,2 cm)

D 15³⁄₈" (39,1 cm)

E 20" (50,8 cm)

F 17¹⁄₁₆" (43,3 cm)

G 11¹⁵⁄₃₂" (29,1 cm)

Panel

de la puerta

del congelador

(sin

despachador)

Panel

de la puerta

del refrigerador

Panel

de la puerta

del congelador

(despachador)

Área de

corte del

despachador

está centrada

de izquierda

a derecha

Dimensión Panel de soporte Panel espaciador

A 19" (48,3 cm) 18³⁄₈" (46,7 cm)

B 31¹⁵⁄₃₂" (79,9 cm) 30³⁄₄" (78,1 cm)

C 67²⁹⁄₃₂" (172,5 cm) 66⁹⁄₁₆" (169,1 cm)

D 14⁷⁄₈" (37,8 cm) 14¹⁄₄" (36,2 cm)

E 19¹⁄₂" (49,6 cm) 18⁷⁄₈" (47,9 cm)

D D

La page est en cours de chargement...

Kenmore 41179 Guide d'installation

Marque: Kenmore

Modèle: 41179

Taper: Guide d'installation

Ce manuel convient également à

41172
41173

Télécharger le PDF

rapport

dans d''autres langues

English: Kenmore 41179 Installation guide
español: Kenmore 41179 Guía de instalación

Kenmore 41179 Guide d'installation

Ce manuel convient également à

Kenmore 41179 Guide d'installation

dans d''autres langues

Autres documents