POWERRECLINE
WITH POWER HEADREST
POWERRECLINE+
WITH POWER HEADREST & LUMBAR
© 2022 La-Z-Boy Incorporated
DOC018380 10/2022
operating instructions
instrucciones de operación
instructions
MOTION SOFAS, CHAIRS & MODULARS
INCLUDING HOME THEATER
SOFÁS, SILLAS Y MODULARES CON MOVIMIENTO
INCLUYENDO TEATRO EN CASA
SOFAS MOBILES, CHAISES ET MODULAIRES
INCLUANT UN THÉATRE MAISON
la-z-boy.com
La-Z-Boy Incorporated
One La-Z-Boy Drive
Monroe, MI 48162
TM
TM
Congratulations!
You are now the proud owner
of a stat e-of-the-art PowerReclineTM with
Power Headrest or Power Headrest and Lumbar
motion sofa, chair or modular by La-Z-Boy.
You have just selected one of the
finest quality upholstered products
produced in the furniture industry,
backed by over 90 years of quality
manufacturing experience.
La-Z-Boy is proud of our designs
and craftsmanship and knows you
will feel the same as you enjoy your
new furniture’s comfort and style.
3
2
Table of Contents
Important Safety Instructions ...................................... 4-5
Regulatory Compliance Statements for Furniture with
Wireless Hand Wand and Bluetooth ...............................6
La-Z-Time®PowerReclineTM with Power Headrest Motion
Sofa, Chair & Modular Assembly Instructions.............. 8-13
La-Z-Time®PowerReclineTM with Power Headrest & Lumbar
Motion Sofa, Chair & Modular Assembly Instructions......14-19
La-Z-Time®PowerReclineTM with Power Headrest
or Power Headrest & Lumbar Motion-Modulars
Assembly Instructions........................................................20- 21
Battery Backup Assembly Instructions....................................22
La-Z-Time®PowerReclineTM with Power Headrest Motion Sofa,
Chair & Modular Operating Instructions............................24-25
La-Z-Time®PowerReclineTM with Power Headrest and Lumbar
Motion Sofa, Chair & Modular Operating Instructions......26-27
Operating Instructions for Power Motion Sofa, Chair &
Modular with Headrest with Optional Wireless Remote....28-29
Operating Instructions for Power Motion Sofa, Chair & Modular
with Headrest and Lumbar with Optional Wireless Remote...30-31
Operating Instructions for Optional Wireless Remote.........32-35
Troubleshooting...................................................................36-37
Furniture Placement Guide......................................................38
IMPORTANT
Read the safety and other instructions before using your
PowerReclineTM with Power or PowerRecline with Power Headrest
and Lumbar product. Keep this manual for future reference.
Disclaimer: The information and products featured in this manual may be
somewhat different from the product you purchased. La-Z-Boy reserves the right
to make substitutions that are equal in quality and performance.
• Users of medical devices should contact their health care provider before using this product.
Do not use this product if you have poor circulation, are immobile, or cannot sense heat, except
as directed by your health care provider.
• Do not use this product where aerosol (spray) products are being used or where oxygen
is being administered.
• Do not operate the unit until the back is installed and locked.
• Before moving the product, disconnect the electrical plug from the wall outlet and secure
the mechanism to prevent unexpected opening or movement. Never move the product by the
mechanism, legrest, handle or reclining back. Disconnect modular units.
• Do not attempt to disassemble or service the pump or motor; no serviceable parts are inside.
Contact your La-Z-Boy®dealer for service.
• Keep hands, arms and body parts away from the open area between a reclined back and an upright
back on a motion sofa or modular. This area must remain clear at all times to provide unobstructed
movement and prevent injury that could occur when a reclined back is returning toward the
upright position.
• The La-Z-Time®PowerReclineTM
, PowerReclineTM with Power Headrest and PowerRecline+TM units are
intended for a single occupant, not exceeding 300 pounds per seat. Do not operate individual seats
or units with more than one occupant in or on any part of the individual seat or unit.
• Do not allow electrical cord to be pinched between moving parts or between the frame and the
floor. Do not place cord under carpet or in a location where it could become worn.
• Unplug the power cord immediately if you detect strange odors or fumes coming from the chair.
• Do not attempt to disconnect the power plug by pulling the power cord. Always hold the power
plug and pull it out.
• If you give this product to someone else, include this Operating Instructions manual.
5
4
– To reduce the risk of electric shock, serious injury or death:
• Disconnect the electrical plug from outlet before cleaning, moving, servicing or when not in use
for an extended period of time.
• Do not use this product if it is wet, in water, around water or any liquid. Do not handle the plug
or remote control with wet hands.
• To prevent suffocation keep plastic bags away from children.
• Plug directly into a wall outlet. Do not use an extension cord, adapter or surge protector.
• Keep cord out of reach of small children, and do not use where it may be a trip hazard.
– To reduce the risk of burns, fire, electric shock,
serious injury or death:
• Keep upholstery away from flames or lit cigarettes. Upholstery may burn rapidly, with toxic gas
and thick smoke. Fires that begin elsewhere in a home may spread and involve upholstery.
For your safety, always use a properly installed smoke detector with working batteries.
• Closely supervise children and disabled persons using this product.
• Sit down in the unit slowly. To avoid tip over, do not throw your weight against the back of the unit.
Move the unit into or out of the reclining position slowly, making sure that no children or pets are
in close proximity.
• This product has many moving parts, serious injury can occur if not used properly. Keep hands,
fingers and body parts away from the mechanism. To reduce the risk of head entrapment and other
injuries, keep children and pets away from openings and moving parts in and around furniture.
• Only the occupant should operate the unit. Never attempt to open the legrest by pulling on it.
• Do not stand, sit, or place extra weight on the arms, back or open legrest.
• To safely exit the unit and prevent a tripping hazard, bring the back upright and close the legrest.
• Do not use this product if it is damaged. Do not use attachments or substitute parts.
• This product is intended for indoor residential use only.
• Provide a clear path for operation of the back and legrest. Place tables and area rugs at a distance
to allow the legrest to fully extend without rubbing or interference.
• Check the condition of the power supplies, electrical cords, plugs, and connectors often. Keep
the power supplies and electrical cords away from heat sources. Never operate the unit with a
damaged power supply, electrical cord, plug, or connector. Contact your La-Z-Boy®dealer for service.
• Do not use unit if power control is damaged or wet. Do not use unit if the hand wand has been
dropped in water or any liquid. Contact your La-Z-Boy®dealer for service.
• This product is not intended for use as a health care device.
• The back of the unit must be lifted for assembly. Please seek assistance if you are unable
to lift at least 45 pounds without strain.
• Do not place containers with hot beverages in the cup holders. The furniture moves and
beverages may spill and cause injury. Do not place oversized or uncovered beverage
containers in the cup holders.
DANGER
WARNING
Important Safety Instructions:
Important: Read these instructions thoroughly before using.
Do not plug in until instructed.
Save These Instructions Save These Instructions
Important Safety Instructions:
Important: Read these instructions thoroughly before using.
Do not plug in until instructed.
– To reduce the risk of product damage:
• To prevent damage to the power supply, do not plug in until instructed.
• Do not move the units while connected together. The purpose of the bracket system is to
connect the units and prevent them from being separated while on the floor. The bracket
system does not provide adequate structural support for the movement of connected units.
• Never operate the unit except when it is on its base in the upright position.
• Some units contain cup holders. Take care to prevent spilling of beverages, which could
damage the cover.
• After 1 minute of continuous operation, allow the system to rest for 9 minutes.
NOTICE
Regulatory Compliance Statements for
Furniture with Wireless Hand Wand and Bluetooth
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy, and if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and receiver
• Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected
• Consult the dealer or an experienced radio/TV technician for help
Changes or modifications not expressly approved by the party responsible for compliance could void
the user’s authority to operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that
may cause undesired operation.
This device complies with Industry Canada’s license-exempt RSS standard(s). Operation is
subject to the following two conditions:
(1) This device may not cause interference, and
(2) This device must accept any interference, including interference that may
cause undesired operation of the device.
Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type
and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio
interference to other users, the antenna type and its gain must be so chosen that the equivalent
isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.
7
6
(Page intentionally left blank)
La-Z-Time®PowerReclineTM with Power Headrest
Motion Sofa, Chair & Modular Assembly Instructions
La-Z-Time®PowerReclineTM with Power Headrest
Motion Sofa, Chair & Modular Assembly Instructions
NOTICE: Do not plug in until instructed.
Some styles (single seat styles) ship with the back unassembled, while others (multiple seat
styles) ship wth the backs assembled.
1. Remove the unit from the package, putting the back off to the side if the back is detached, and
gently roll the unit forward so that it rests on its front or top side. On units with protective pads,
cut the plastic ties and remove them from the bottom of the unit. (FIGURE 1).
2. Gently roll the unit back to the upright position.
3. Once the furniture is unpacked, carefully remove the electrical components bag (either red, blue
or orange) from the body bracket and set aside; depending on the product purchased, inside the
bag are the power supply, power cord, optional remote, three AAA batteries for the optional
remote and for power motion sofa and loveseat units, a Y-cable. (FIGURE 2 and 3).
•For styles with the backs assembled, proceed to step 5.
– To reduce the risk of injury:
• Do not operate the unit until the back is installed and locked.
• The back of the unit must be lifted for assembly. Please seek assistance if you are
unable to lift at least 45 pounds without strain.
WARNING
4. Install the back on styles that ship with the back unassembled.
•Lay the back front side down on the seat, turn the outside back upholstery cover over, toward
the front of the unit, and locate the back and body brackets (FIGURE 4).
•Lift the back at a slight angle and align the brackets on the back with the brackets on the body.
•Lower the back onto the body, taking care not to pinch the cables between any metal or wood
parts and making sure the back and body brackets are completely engaged.
Note: The back is easier to install when holding it level and lowering it evenly onto
the body brackets.
- Lift the back upholstery cover and look up into the back to visually confirm that both sets of back
and body brackets are engaged (FIGURE 5). If one or both brackets are not engaged, or if cables are
pinched, remove the back and repeat the steps above.
- If you are unable to install the back properly, contact your La-Z-Boy®dealer for assistance.
•Lock the brackets by using a screwdriver to push down the locking levers (FIGURE 6).
(PowerReclineTM with Power Headrest Assembly Instructions Continued)
FIGURE 1 (Style U4A Featured)FIGURE 2
FIGURE 3FIGURE 4
FIGURE 5FIGURE 6
Body
Bracket
Back and Body
Brackets Engaged
Back
Bracket Locking
Lever
Locking
Position
9
8
Back
Bracket
* For power motion sofas and loveseats
Power
Supply
120 Volt
Power Cord
Y-Cable
La-Z-Time®PowerReclineTM with Power Headrest
Motion Sofa, Chair & Modular Assembly Instructions
5. Make electrical connection between the back and the body.
•Locate and identify the electrical connection between the back and the body. For styles with the
backs shipped installed, pull the lower outside back upholstery cover to release the fastening tape
from the bottom rear rail, and lift the cover to locate the connectors.
- The blue or brown connectors on the left side (sitting) are for the adjustable headrest feature. One
connector routes from the bottom of the back and the other from the junction box mounted to the body.
•Connect the adjustable headrest cables (FIGURE 7). Align the pins and sockets in the blue or brown
connectors, push the connectors together and close the locking cover to secure each connection.
6. Attach the outside back upholstery cover.
•Locate the fastening tape on the outside back upholstery cover and the fastening tape on the side(s)
and bottom of the rear body rail (FIGURE 8); location of fastening tape varies by style.
•Pull the outside back upholstery cover down tight and firmly press the fastening tape on the outside
back upholstery cover to the fastening tape on the body.
7. Choose a location for the power furniture that is close to an electrical outlet.
– To reduce the risk of injury:
• Provide a clear path for operation of the back and legrest. Place tables and area rugs
at a distance to allow the legrest to fully extend without rubbing or interference.
WARNING
8. Adjustable glides are standard on units with metal base rails. Adjust the glides to a height that provides
an unobstructed path for operation of the legrest (see Furniture Placement Guide).
•Each glide is attached to the base rail by one jam nut and one lock washer on top of the front
attachment bracket, and one jam nut on the bottom of the base rail (FIGURE 9, Motion-Modular unit
featured). Loosen the jam nut located on top of the front attachment bracket.
•Holding the top jam nut, turn the glide clockwise to lower the unit or counterclockwise to
raise the unit.
•Tighten the bottom jam nut to the base rail, then tighten the top jam nut to the lock washer on top
of the front attachment bracket. Make sure both jam nuts are tight to prevent the bracket from
rotating on the base rail.
•Repeat this step for each adjustable glide, if necessary.
11
10
(PowerReclineTM with Power Headrest Assembly Instructions Continued)
La-Z-Time®PowerReclineTM with Power Headrest
Motion Sofa, Chair & Modular Assembly Instructions
FIGURE 7FIGURE 8
FIGURE 9
Fastening Tape
Adjustable Headrest
Connection (Blue or Brown)
Upper Jam Nut Lock Washer
Front
Attachment
Bracket
Lower
Jam Nut
Adjustable
Glide Base Rail
La-Z-Time®PowerReclineTM with Power Headrest Motion
Sofa, Chair & Modular Assembly Instructions
9. Identify the electrical components to be used in the following assembly steps (FIGURE 10).
Components vary by style.
10. Locate the motor connector behind the power unit (FIGURE 11).
11. For single motion seat units, connect the power supply to the motor connector (FIGURE 12). For units
with two motion seats, skip to Step 13.
12. Connect the 120 volt power cord to the power supply (FIGURE 13). Do not plug in until
instructed in the Operating Instructions.
13. For two motion seat units, connect the Y-Cable to both motor connectors (FIGURE 14), and then connect the
Y-Cable to the power supply (FIGURE 15).
14. Connect the 120-volt power cord to the power supply (FIGURE 16). Do not plug in unit until
instructed in the Operating Instructions.
15. To remove the backs, unplug the 120 volt power cord from the electrical outlet and disconnect
the power supply from the motor connector behind the power motion-modular unit. Reverse
the Assembly Instructions steps.
13
12
FIGURE 10
* For power motion sofas and loveseats
La-Z-Time®PowerReclineTM with Power Headrest Motion
Sofa, Chair & Modular Assembly Instructions
FIGURE 11 FIGURE 12
FIGURE 13 FIGURE 14
FIGURE 15 FIGURE 16
Power
Supply
Motor
Connector
120 Volt
Power Cord
Power
Supply
Motor
Connector
Make this
connection
Make this
connection
Make this
connection
Motor
Connector
Y-Cable
Make this
connection
Power
Supply
Y-Cable Power
Supply
120 Volt
Power Cord
Power
Supply
120 Volt
Power Cord
Y-Cable
(PowerReclineTM with Power Headrest Assembly Instructions Continued)
La-Z-Time®PowerReclineTM with Power Headrest
and Lumbar Motion Sofa, Chair & Modular
Assembly Instructions
La-Z-Time®PowerReclineTM with Power Headrest
and Lumbar Motion Sofa, Chair & Modular
Assembly Instructions
NOTICE: Do not plug in until instructed.
Some styles (single seat styles) ship with the back unassembled, while others (multiple seat
styles) ship wth the backs assembled.
1. Remove the unit from the package, putting the back off to the side if the back is detached, and
gently roll the unit forward so that it rests on its front or top side. On units with protective pads,
cut the plastic ties and remove them from the bottom of the unit. (FIGURE 1).
2. Gently roll the unit back to the upright position.
3. Once the furniture is unpacked, carefully remove the electrical components bag (either red, blue
or orange) from the body bracket and set aside; depending on the product purchased, inside the
bag are the power supply, power cord, optional remote, three AAA batteries for the optional
remote and for power motion sofa and loveseat units, a Y-cable. (FIGURE 2 and 3).
•Remove the power supply from the box and set aside (FIGURE 3).
•For styles with the backs assembled, proceed to step 5.
– To reduce the risk of injury:
• Do not operate the unit until the back is installed and locked.
• The back of the unit must be lifted for assembly. Please seek assistance if you are
unable to lift at least 45 pounds without strain.
WARNING
4. Install the back on styles that ship with the back unassembled.
•Lay the back front side down on the seat, turn the outside back upholstery cover over, toward
the front of the unit, and locate the back and body brackets (FIGURE 4).
•Lift the back at a slight angle and align the brackets on the back with the brackets on the body.
•Lower the back onto the body, taking care not to pinch the cables between any metal or wood
parts and making sure the back and body brackets are completely engaged.
Note: The back is easier to install when holding it level and lowering it evenly onto
the body brackets.
- Lift the back upholstery cover and look up into the back to visually confirm that both sets of back
and body brackets are engaged (FIGURE 5). If one or both brackets are not engaged, or if cables are
pinched, remove the back and repeat the steps above.
- If you are unable to install the back properly, contact your La-Z-Boy®dealer for assistance.
•Lock the brackets by using a screwdriver to push down the locking levers (FIGURE 6).
FIGURE 1 (Style X4A Featured)FIGURE 2
FIGURE 3FIGURE 4
FIGURE 5FIGURE 6
Body
Bracket
Back and Body
Brackets Engaged
Back
Bracket Locking
Lever
Locking
Position
15
14
Back
Bracket
(PowerReclineTM with Power Headrest and Lumbar
Assembly Instructions Continued)
* For power motion sofas and loveseats
Power
Supply
120 Volt
Power Cord
Y-Cable
La-Z-Time®PowerReclineTM with Power Headrest
and Lumbar Motion Sofa, Chair & Modular
Assembly Instructions
5. Make electrical connection between the back and the body.
•Locate and identify the electrical connection between the back and the body. For styles with the
backs shipped installed, pull the lower outside back upholstery cover to release the fastening tape
from the bottom rear rail, and lift the cover to locate the connectors.
- The blue or brown connectors on the right side (sitting) are for the adjustable lumbar feature. One
connector routes from the bottom of the back and the other from the junction box mounted to the body.
- The gray or orange connectors on the left side (sitting) are for the adjustable headrest feature.
One connector routes from the bottom of the back and the other from the junction box mounted
to the body.
•Connect the adjustable headrest and lumbar cables (FIGURE 7). Align the pins and sockets in the
connectors (matching colors), push the connectors together and close the locking cover to
secure each connection.
6. Attach the outside back upholstery cover.
•Locate the fastening tape on the outside back upholstery cover and the fastening tape on the side(s)
and bottom of the rear body rail (FIGURE 8); location of fastening tape varies by style.
•Pull the outside back upholstery cover down tight and firmly press the fastening tape on the outside
back upholstery cover to the fastening tape on the body.
7. Choose a location for the power furniture that is close to an electrical outlet.
– To reduce the risk of injury:
• Provide a clear path for operation of the back and legrest. Place tables and area rugs
at a distance to allow the legrest to fully extend without rubbing or interference.
WARNING
8. Adjustable glides are standard on units with metal base rails. Adjust the glides to a height that provides
an unobstructed path for operation of the legrest (see Furniture Placement Guide).
•Each glide is attached to the base rail by one jam nut and one lock washer on top of the front
attachment bracket, and one jam nut on the bottom of the base rail (FIGURE 9, Motion-Modular unit
featured). Loosen the jam nut located on top of the front attachment bracket.
•Holding the top jam nut, turn the glide clockwise to lower the unit or counterclockwise to
raise the unit.
•Tighten the bottom jam nut to the base rail, then tighten the top jam nut to the lock washer on top
of the front attachment bracket. Make sure both jam nuts are tight to prevent the bracket from
rotating on the base rail.
•Repeat this step for each adjustable glide, if necessary.
17
16
La-Z-Time®PowerReclineTM with Power Headrest
and Lumbar Motion Sofa, Chair & Modular
Assembly Instructions
FIGURE 7FIGURE 8
FIGURE 9
Fastening Tape
Adjustable Lumbar
Connection (Blue or Brown)
Upper Jam Nut Lock Washer
Front
Attachment
Bracket
Lower
Jam Nut
Adjustable
Glide Base Rail
Adjustable Headrest
Connection (Gray or Orange)
(PowerReclineTM with Power Headrest and Lumbar
Assembly Instructions Continued)
La-Z-Time®PowerReclineTM with Power Headrest
and Lumbar Motion Sofa, Chair & Modular
Assembly Instructions
9. Identify the electrical components to be used in the following assembly steps (FIGURE 10).
Components vary by style.
10. Locate the motor connector behind the power unit (FIGURE 11).
11. For single motion seat units, connect the power supply to the motor connector (FIGURE 12). For units
with two motion seats, skip to Step 13.
12. Connect the 120 volt power cord to the power supply (FIGURE 13). Do not plug in until
instructed in the Operating Instructions.
13. For two motion seat units, connect the Y-Cable to both motor connectors (FIGURE 14), and then connect the
Y-Cable to the power supply (FIGURE 15).
14. Connect the 120-volt power cord to the power supply (FIGURE 16). Do not plug in unit until
instructed in the Operating Instructions.
15. To remove the backs, unplug the 120 volt power cord from the electrical outlet and disconnect
the power supply from the motor connector behind the power motion-modular unit. Reverse
the Assembly Instructions steps.
19
18
FIGURE 10
* For power motion sofas and loveseats
La-Z-Time®PowerReclineTM with Power Headrest
and Lumbar Motion Sofa, Chair & Modular
Assembly Instructions
FIGURE 11 FIGURE 12
FIGURE 13 FIGURE 14
FIGURE 15 FIGURE 16
Power
Supply
Motor
Connector
120 Volt
Power Cord
Power
Supply
Motor
Connector
Make this
connection
Make this
connection
Power
Supply
120 Volt
Power Cord
Y-Cable
(PowerReclineTM with Power Headrest and Lumbar
Assembly Instructions Continued)
Make this
connection
Motor
Connector
Y-Cable
Make this
connection
Power
Supply
Y-Cable Power
Supply
120 Volt
Power Cord
1"
1"
21
20
Motion-Modular units with metal base rails have one bracket in the back and one “U” bracket in the
front on the right side (sitting) of modular units without right side arms, and two stud mounts with
threaded studs on the left side (sitting) of modular units without left side arms (FIGURE 17).
Motion-Modular units with wood legs have one side mount bracket in the back and one “U” bracket
in the front on the right side (sitting) of modular units without right side arms, and two threaded
studs on the left side (sitting) of modular units without left side arms (FIGURE 18).
17. Use a T-30 torx driver to loosen the threaded studs to approximately 1"; this measurement may
vary depending on the fabric and style (FIGURE 19). The threaded studs are located on the left
side (sitting) of modular units without left side arms.
18. To start, place the units to be attached next to each other, about 2" apart. Position the unit with the
threaded studs slightly behind the unit with the attachment brackets. Separate the fronts of the
units to be connected, about 6" apart. Slide the rear of the unit with the threaded studs toward the
unit with the attachment brackets, aligning the threaded studs to the rear bracket. Pull the unit with
the threaded studs forward to engage the rear bracket.
FIGURE 17
FIGURE 18
FIGURE 19 FIGURE 20
NOTICE: To reduce the risk of product damage –
• Do not move the units while connected together. The purpose of the bracket system is
to connect the units and prevent them from being separated while on the floor. The bracket
system does not provide adequate structural support for the movement of connected units.
22. All modular units must be disconnected to safely move the modular group. To disconnect the
units, lift up the left side (sitting) modular unit (with threaded studs) approximately 3" to clear
the front attachment bracket, move the front of the unit over and return it to the floor. Slide the
unit with the threaded studs backward to disengage the rear bracket.
Rear Rail Bracket
Front Rail
“U” Bracket
Stud
Mount
Threaded
Stud
Threaded
Stud
Rear
Side
Mount
Bracket
Front Side Mount
“U” Bracket
Leg UnitsBase UnitsLeg UnitsBase Units
Front Side Mount
“U” Bracket
Front Rail “U”
Bracket
Threaded
Stud
Threaded
Stud
Stud
Mount
19. Lift the front of the unit with the threaded stud approximately 3" off the ground, aligning it
to the unit with the attachment bracket. Gently lower the threaded stud into the front attachment
bracket (FIGURE 20). Keep feet clear of the unit when lowering into position.
Note: Due to variations in upholstery and style, the threaded stud length may need to be adjusted to
fit into the attachment brackets or control gaps between units. Loosen or tighten the threaded studs
to provide adequate clearance.
20. Continue connecting the modular units until all have been securely joined.
21. Proceed to the Battery Backup Assembly Instructions to complete assembly.
– To reduce the risk of serious injury:
• The front of the unit must be raised to engage the front bracket. Please seek assistance
if you are unable to lift at least 57 pounds.
• Keep feet clear of the unit when lowering into position.
WARNING
NOTICE: To reduce the risk of product damage –
• Lift from the base rail. Do not lift from the upholstery or the bottom of the legrest.
La-Z-Time®PowerReclineTM with Power Headrest
or Power Headrest & Lumbar Motion-Modulars
Assembly Instructions
La-Z-Time®PowerReclineTM with Power Headrest
or Power Headrest & Lumbar Motion-Modulars
Assembly Instructions
23
22
Battery Backup Assembly Instructions
NOTICE: Replace the power supply batteries every six months
and after each power failure use.
Power Recliner Supply Specifications:
Power
Supply
(2) 9-Volt
Name Brand Alkaline Batteries
Battery Cover
Input: AC100-240V~50/60Hz 2.0A
Output: DC 29V 1.6A
The performance of the built-in battery backup cannot be guaranteed. The backup system is
designed to return a reclined unit to the upright, closed position for exiting ease during a power
interruption. It is not intended to recline the unit. If you require continuing use during a power
outage, you should purchase a separate battery backup system. Contact your La-Z-Boy®dealer
for more information.
The operating speed is reduced when operating on battery backup. Additionally, the USB charging
port is disabled when the unit is powered by the battery backup only.
Always maintain constant, even pressure on the button when operating on battery backup to
reduce the energy consumption.
Replace the batteries with fresh, name brand (Duracell/Energizer), alkaline batteries every 6 months
and after each power failure use.
The battery backup is located in the power supply and uses two 9-volt alkaline batteries (not included).
1. Unplug the 120 volt power cord from the electrical outlet, and:
•For a power motion sofa, disconnect the power supply from the motor connectors
behind the motion sofa; there are two motor connections to disconnect, one behind each
reclining seat.
•For a modular unit, disconnect the power supply from the motor connector behind the unit.
2. The battery compartment is located on the side of the power supply. Slide the battery cover
up to access the battery compartment.
3. Snap the connection caps on the battery terminals. Place the batteries in the power supply.
4. Slide the battery cover over the batteries.
5. Proceed to the Operating Instructions.
(Page intentionally left blank)
25
24
La-Z-Time®PowerRecline with Power Headrest Motion
Sofa, Chair & Modular Operating Instructions
– To reduce the risk of electric shock,
serious injury or death:
• Plug directly into a wall outlet. Do not use an extension cord, adapter or surge protector.
DANGER
– To reduce the risk of serious injury:
• Do not attempt to disassemble or service the pump or motor; no serviceable parts are
inside. Contact your La-Z-Boy®dealer for service.
• Check the condition of the power supplies, electrical cords, plugs, and connectors
often. Keep the power supplies and electrical cords away from heat sources.
Never operate the unit with a damaged power supply, electrical cord, plug,
or connector. Contact your La-Z-Boy®dealer for service.
• The La-Z-Time®power units are intended for a single occupant, not exceeding 300 pounds
per seat. Do not operate individual seats or units with more than one occupant in or on
any part of the individual seat or unit.
WARNING
Operating the Unit:
To avoid product damage, the back recline and legrest extension features should not be operated
continuously for extended periods of time. After 1 minute of continuous operation, allow these
features to rest for 9 minutes.
Plug the power cord directly into a wall outlet. Never stretch or strain a cord.
The power features are operated by the toggles on the Control Panel located on the outside arm.
Each feature has a dedicated toggle for operation.
•Press rearward on the Recline (bottom) toggle to recline the back and raise the legrest.
Release the toggle when the back and legrest reach the desired position, or are fully reclined.
•Press the Headrest (top toggle) forward to increase the amount of adjustment.
Press the toggle rearward to decrease the amount of adjustment.
•The Control Panel also features a Home button for personal, effortless operation and added
comfort. Press and release the Home button and the furniture automatically moves to its
home position.
Troubleshooting for Legrest Operation
If the legrest stops moving while closing, it may have encountered an obstruction.
1. Check to make sure there are no obstructions. Lift and hold the legrest up, look for obstructions
and remove them.
2. The legrest uses spring tension to close, and will close quickly when the obstruction is removed.
Release the legrest slowly to prevent it from slamming shut.
NOTICE: After 1 minute of continuous operation, allow the system
to rest for 9 minutes.
La-Z-Time®PowerRecline with Power Headrest Motion
Sofa, Chair & Modular Operating Instructions
USB Charging Port Instructions
Plug a small portable electronic device into the USB charging port. The USB port is for charging only
and does not have data transferring capabilities.
USB Output Specifications:
5VDC, 1.0A
Headrest Toggle
Press the Headrest toggle forward and hold to rotate the headrest forward.
Or press it rearward and hold to return the headrest. Release the button to
stop the headrest in any position, or when fully extended or fully retracted.
– To reduce the risk of serious injury:
• Do not use unit if power control is damaged or wet. Contact your La-Z-Boy®dealer for service.
WARNING
Recline and Return
Press the Recline and Return toggle rearward and hold to extend the legrest and
recline the back. Or press it forward and hold to return the legrest and back to
the upright and fully closed position. Release the button to stop the legrest and
back recline in any position, or when fully reclined or fully retracted.
(PowerReclineTM with Power Headrest Motion Sofa, Chair
& Modular Operating Instructions Continued)
USB Port
Headrest Retract Headrest Extend
Recline Return
Home Button
Press and release
the Home Button
to return the
furniture to the
upright, closed,
stored position.
27
26
La-Z-Time®PowerRecline with Power Headrest
and Lumbar Motion Sofa, Chair & Modular
Operating Instructions
– To reduce the risk of electric shock,
serious injury or death:
• Plug directly into a wall outlet. Do not use an extension cord, adapter or surge protector.
DANGER
– To reduce the risk of serious injury:
• Do not attempt to disassemble or service the pump or motor; no serviceable parts are
inside. Contact your La-Z-Boy®dealer for service.
• Check the condition of the power supplies, electrical cords, plugs, and connectors
often. Keep the power supplies and electrical cords away from heat sources.
Never operate the unit with a damaged power supply, electrical cord, plug,
or connector. Contact your La-Z-Boy®dealer for service.
• The La-Z-Time®power units are intended for a single occupant, not exceeding 300 pounds
per seat. Do not operate individual seats or units with more than one occupant in or on
any part of the individual seat or unit.
WARNING
Operating the Unit:
To avoid product damage, the back recline and legrest extension features should not be operated
continuously for extended periods of time. After 1 minute of continuous operation, allow these
features to rest for 9 minutes.
Plug the power cord directly into a wall outlet. Never stretch or strain a cord.
The power features are operated by the toggles on the Control Panel located on the outside arm.
Each feature has a dedicated toggle for operation.
•Press rearward on the Recline (bottom) toggle to recline the back and raise the legrest.
Release the toggle when the back and legrest reach the desired position, or are fully reclined.
•Press the Headrest and Lumbar toggles forward to increase the amount of adjustment.
Press the toggle rearward to decrease the amount of adjustment.
•The Control Panel also features a Home button for personal, effortless operation and added
comfort. Press and release the Home button and the furniture automatically moves to its
home position.
Troubleshooting for Legrest Operation
If the legrest stops moving while closing, it may have encountered an obstruction.
1. Check to make sure there are no obstructions. Lift and hold the legrest up, look for obstructions
and remove them.
2. The legrest uses spring tension to close, and will close quickly when the obstruction is removed.
Release the legrest slowly to prevent it from slamming shut.
NOTICE: After 1 minute of continuous operation, allow the system
to rest for 9 minutes.
La-Z-Time®PowerRecline with Power Headrest
and Lumbar Motion Sofa, Chair & Modular
Operating Instructions
USB Charging Port Instructions
Plug a small portable electronic device into the USB charging port. The USB port is for charging only
and does not have data transferring capabilities.
USB Output Specifications:
5VDC, 1.0A
– To reduce the risk of serious injury:
• Do not use unit if power control is damaged or wet. Contact your La-Z-Boy®dealer for service.
WARNING
Recline and Return
Press the Recline and Return toggle rearward
and hold to extend the legrest and recline the
back. Or press it forward and hold to return
the legrest and back to the upright and fully
closed position. Release the button to stop the
legrest and back recline in any position, or
when fully reclined or fully retracted.
Lumbar Toggle
Press the Lumbar toggle forward and hold
to increase the lumbar intensity. Or press
it rearward and hold to decrease lumbar
intensity. Release the button to stop the
lumbar in any position, or when fully
extended or fully retracted.
(PowerReclineTM with Power Headrest and Lumbar Motion Sofa,
Chair & Modular Operating Instructions Continued)
Headrest Toggle
Press the Headrest toggle forward and hold to rotate the headrest forward.
Or press it rearward and hold to return the headrest. Release the button to
stop the headrest in any position, or when fully extended or fully retracted.
USB Port
Headrest Retract Headrest Extend
Recline Lumbar Retract
Home Button
Press and release
the Home Button
to return the
furniture to the
upright, closed,
stored position.
Return Lumbar Extend
– To reduce the risk of electric shock, serious injury
or death:
• Liquids exposed to electricity pose an immediate risk of electric shock. Do not use this
unit if the power control is damaged, wet, in contact with or near spilled water or any liquid.
Do not use the unit if the button activation switch has been exposed to water or any liquid.
Do not handle the plug or remote control with wet hands.
• Do not attempt to disassemble, modify or service the product or motor; no serviceable
parts are inside. Only use genuine La-Z-Boy®parts and battery packs with the furniture.
Contact your La-Z-Boy dealer for service.
DANGER
– To reduce the risk of electric shock or serious injury:
• Plug directly into a wall outlet. Do not use an extension cord, adapter, surge protector or power strip.
• Sit down in the unit slowly. To avoid tip over, do not throw your weight against the back
of the unit. Move the unit into or out of the reclining position slowly, making sure that no
children or pets are in close proximity.
• The La-Z-Time®Power units are intended for a single occupant, not exceeding 300
pounds per seat. Do not operate individual seats or units with more than one occupant in
or on any part of the individual seat or unit.
• To safely exit the unit and prevent a tripping hazard, bring the back upright and close the legrest.
WARNING
Operating Instructions for Power Motion Sofa, Chair &
Modular with Headrest with Optional Wireless Remote
After 1 minute of continuous operation, allow the system to rest for 9 minutes.
NOTICE:
Only proceed after having followed the Assembly Instructions completely.
Operating Instructions for Furniture with Optional Wireless Remote:
Plug the power cord directly into a wall outlet. Make sure there is enough slack in the cord running
from the chair to the outlet to allow for reclining. Never stretch or strain a cord.
The power features are operated by the buttons on the remote located in the
remote cradle on the outside arm, and by the buttons on the cradle itself. Each feature
has a dedicated button on the remote for independent operation of the feature, or
simultaneous operation of multiple features when more than one button is pressed. *
A press on the left side of a button (arrow UP) on the remote increases the
amount of recline or adjustment, while a press on the right side (arrow DOWN)
decreases the amount of recline or adjustment.
The Remote and Cradle both feature a Memory I, Memory II and Home button for personal, effortless
operation and added comfort. Two preferred recline settings may be stored for a more enjoyable reclining
experience at the mere press of a button. Press and release a stored Memory button (not holding for more
than 2 seconds) and the furniture automatically moves to the stored setting. Press and release the Home
button and the furniture automatically moves to its home, or upright, closed and stored position.
A handy USB port for charging small personal electronic devices is located in the cradle to keep
your devices close at hand and ready for use at all times.
Unplug the power supply from the wall outlet if you are going to be away from your residence for
an extended period of time.
* When the furniture is powered by the 9-volt battery backup or the optional rechargeable
lithium-ion pack, only two features can be operated at the same time.
Operating Instructions for Power Motion Sofa, Chair &
Modular with Headrest with Optional Wireless Remote
Recline and Return
Press the Recline and Return
button arrow UP and hold to
extend the legrest and recline the
back. Or press the arrrow DOWN
and hold to return the legrest
and back to the upright and fully
closed position. Release the button
to stop the legrest and back
recline in any position, or when
fully reclined or fully retracted.
Home Button
Press and release the Home button to
automatically return the furniture to its
upright, closed and stored position.
Memory I and
Memory II Buttons
Press and release the
Memory I or Memory II
button to automatically move
the furniture to a stored setting.
(pressing and holding
stores the setting)
Headrest Button
Press the Headrest button
arrow UP and hold to rotate
the headrest forward. Or
press the arrow DOWN and
hold to return the headrest.
Release the button to stop
the headrest in any position
or when fully extended or
fully retracted.
– To reduce the risk of burns, electric shock,
serious injury or death:
• Liquids exposed to electricity pose an immediate risk of electric shock. Do not use this
unit if the power control is damaged, wet, in contact with or near spilled water or any
liquid. Do not use the unit if the button activation switch has been exposed to water or
any liquid. Do not handle the plug or remote control with wet hands.
DANGER
29
28
31
30
– To reduce the risk of electric shock, serious injury
or death:
• Liquids exposed to electricity pose an immediate risk of electric shock. Do not use this
unit if the power control is damaged, wet, in contact with or near spilled water or any liquid.
Do not use the unit if the button activation switch has been exposed to water or any liquid.
Do not handle the plug or remote control with wet hands.
• Do not attempt to disassemble, modify or service the product or motor; no serviceable
parts are inside. Only use genuine La-Z-Boy®parts and battery packs with the furniture.
Contact your La-Z-Boy dealer for service.
DANGER
– To reduce the risk of electric shock or serious injury:
• Plug directly into a wall outlet. Do not use an extension cord, adapter, surge protector
or power strip.
• Sit down in the unit slowly. To avoid tip over, do not throw your weight against the back
of the unit. Move the unit into or out of the reclining position slowly, making sure that
no children or pets are in close proximity.
• The La-Z-Time®Power units are intended for a single occupant, not exceeding 300 pounds
per seat. Do not operate individual seats or units with more than one occupant in or on any
part of the individual seat or unit.
• To safely exit the unit and prevent a tripping hazard, bring the back upright and close the legrest.
WARNING
Operating Instructions for Power Motion Sofa, Chair & Modular
with Headrest and Lumbar with Optional Wireless Remote
After 1 minute of continuous operation, allow the system to rest for 9 minutes.
NOTICE:
Only proceed after having followed the Assembly Instructions completely.
Operating Instructions for Furniture with Optional Wireless Remote:
Plug the power cord directly into a wall outlet. Make sure there is enough slack in the cord running
from the chair to the outlet to allow for reclining. Never stretch or strain a cord.
The power features are operated by the buttons on the remote located in the
remote cradle on the outside arm, and by the buttons on the cradle itself. Each feature
has a dedicated button on the remote for independent operation of the feature, or
simultaneous operation of multiple features when more than one button is pressed. *
A press on the left side of a button (arrow UP / +) on the remote increases the
amount of recline or adjustment, while a press on the right side (arrow DOWN / -)
decreases the amount of recline or adjustment.
The Remote and Cradle both feature a Memory I, Memory II and Home button for personal, effortless
operation and added comfort. Two preferred recline settings may be stored for a more enjoyable reclining
experience at the mere press of a button. Press and release a stored Memory button (not holding for more
than 2 seconds) and the furniture automatically moves to the stored setting. Press and release the Home
button and the furniture automatically moves to its home, or upright, closed and stored position.
A handy USB port for charging small personal electronic devices is located in the cradle to keep
your devices close at hand and ready for use at all times.
Unplug the power supply from the wall outlet if you are going to be away from your residence for
an extended period of time.
* When the furniture is powered by the 9-volt battery backup or the optional rechargeable
lithium-ion pack, only two features can be operated at the same time.
Operating Instructions for Power Motion Sofa, Chair & Modular
with Headrest and Lumbar with Optional Wireless Remote
Recline and Return
Press the Recline and Return
button arrow UP and hold to
extend the legrest and recline
the back. Or press the arrrow
DOWN and hold to return the
legrest and back to the upright
and fully closed position.
Release the button to stop the
legrest and back recline in any
position, or when fully reclined
or fully retracted.
Home Button
Press and release the Home button to
automatically return the furniture to its
upright, closed and stored position.
Memory I and
Memory II Buttons
Press and release the
Memory I or Memory II
button to automatically move
the furniture to a stored setting.
(pressing and holding
stores the setting)
Headrest Button
Press the Headrest button
arrow UP and hold to rotate the
headrest forward. Or press the
arrow DOWN and hold to return
the headrest. Release the button
to stop the headrest in any
position or when fully extended
or fully retracted.
Lumbar Button
Press the Lumbar button
+ and hold to increase the
lumbar intensity. Or press the
-- and hold to decrease lumbar
intensity. Release the button
to stop the lumbar in any
position or when fully
extended or full retracted.
– To reduce the risk of burns, electric shock,
serious injury or death:
• Liquids exposed to electricity pose an immediate risk of electric shock. Do not use this
unit if the power control is damaged, wet, in contact with or near spilled water or any
liquid. Do not use the unit if the button activation switch has been exposed to water or
any liquid. Do not handle the plug or remote control with wet hands.
DANGER
Operating Instructions for
Optional Wireless Remote
Memory I Button
Press and release the Memory I button
to automatically move the furniture to the
stored setting.
(pressing and holding stores the setting)
Home Button
Press and release the Home button to
automatically return the furniture to its
upright, closed and stored position.
Find Me
Press the Find Me
button to send a signal
and locate the remote.
LED lights flash and a
loud tone plays from
the remote when the
signal is received, and
the remote equipped
with three working
AAA alkaline batteries.
Do Not Disturb
Slide the Do Not Disturb button to the Left (as facing)
position to turn on the feature and block out
communication between the remote and furniture.
This essentially turns off the remote commands
to safeguard against undesired movement of the
furniture. Slide it to the right (as facing) to turn off the
feature, and allow communication with the remote.
USB Port
Connect a USB cable
to the port to charge
a device.
– To reduce the risk of burns, electric shock,
serious injury or death:
• Liquids exposed to electricity pose an immediate risk of electric shock. Do not use this
unit if the power control is damaged, wet, in contact with or near spilled water or any
liquid. Do not use the unit if the button activation switch has been exposed to water or
any liquid. Do not handle the plug or remote control with wet hands.
DANGER
Memory II Button
Press and release the Memory II button
to automatically move the furniture to the
stored setting.
(pressing and holding stores the setting)
USB Output Specifications:
5 VDC, 1.0A
33
32
Operating Instructions for
Optional Wireless Remote
Install Batteries in the Remote:
The remote requires three (3) AAA alkaline batteries (included; packed inside the electrical components bag).
1. Remove the remote and AAA batteries from the electrical components bag. Remove the plastic
wrap from the batteries.
2. Turn the remote over to access the battery compartment.
3. Slide the battery compartment cover off and set aside (FIGURE 1).
4. Insert three AAA batteries oriented to match the polarity as in indicated by the markings in the
battery compartment (FIGURES 2 and 3).
5. Slide the battery compartment cover back in place to close the compartment.
FIGURE 1FIGURE 2FIGURE 3
Remove
Back Cover
Insert (3) AAA Alkaline Batteries
Polarity Markings Inside
the Battery Compartment
35
34
Operating Instructions for
Optional Wireless Remote
To Program and Use Memory I or Memory II:
1. Use the remote to adjust the furniture to the best and most comfortable position for you.
2. Press and hold the Memory I or Memory II button for three (or more) seconds on either the remote or the cradle.
3. Listen for the “beep” and watch for the LED lights to flash on the remote to indicate the setting was
saved in memory.
• Memory I setting plays a single beep and flashes a single light to indicate a successful save.
• Memory II setting plays a double beep and flashes a double light to indicate a successful save.
• Three quick beeps and flashes of light are transmitted from the remote when the setting did
not successfully save.
4. The next time you use your furniture, press and release either the Memory I or Memory II button (not holding
longer than two seconds), on either the remote or cradle. The furniture automatically moves to the saved
setting. If no setting is stored, the furniture moves to its home, upright, closed and stored position instead.
Pressing any button on the remote or cradle, while the furniture is in motion from a Memory button press, stops
the automatic movement of the furniture. The furniture does not restart once the button is released. Another
press of the Memory I or Memory II button is required to start the furniture in motion again.
If the Memory I or Memory II button is pressed on the remote and then the Do Not Disturb button (cradle) is
turned on, all motion stops. The furniture does not automatically resume and continue the move to a Memory I
or Memory II setting when the Do Not Disturb button is turned off. If the Memory I or Memory II button is pressed
on the cradle and then the Do Not Disturb button is pressed on the cradle, the furniture continues to move to the
stored setting. All Remote commands are ignored when Do Not Disturb is on.
NOTE: All features start in motion upon a Memory button press if the feature is programmed to recline or extend,
except for the headrest.* When the headrest is programmed to extend, the headrest does not start until the
recline reaches 100% recline or its programmed setting if less than 100%. This is done to guard against an
undesirable positioning of the head and neck when moving into the stored recline setting.
* Furniture must be plugged into a power outlet or powered by the optional rechargeable lithium-ion battery
pack for the Memory feature to function. This feature is disabled when powered by the 9-volt battery backup.
Additionally, when powered by the optional rechargeable lithium-ion battery pack, only two features operate at
the same time.
To Use the Home Button:
The Home button returns the back is to its fully upright position and the legrest, headrest and optional lumbar
to the fully retracted and closed position.
Press and release the Home button. The furniture automatically starts in motion, moving the back, legrest,
headrest and lumbar back to the upright and retracted positions.
All motion stops if any button is pressed while the furniture is moving to home. The motion does not resume
when the button is released. Another press and release of the Home button is required to restart the home program.
NOTE: When the furniture is powered by the 9-volt battery back-up, the back and legrest move to the home
position first. Once the back and legrest are fully upright and retracted, then the headrest and lumbar return to
the retracted, home position. When powered by the optional rechargeable lithium-ion battery pack, the headrest
and lumbar move to the Home position first, and then the back and legrest move to Home.
Operating Instructions for
Optional Wireless Remote
To Use the Do Not Disturb:
Turning on the Do Not Disturb feature blocks the furniture’s communication with the remote. When the remote is
blocked, the only features available for use are those with commands, or buttons on the cradle—these are the
Memory I, Memory II, Home and Find Me features.
Slide the Do Not Disturb button to the left (facing) position to turn on the feature and block out all commands
coming from the remote, allowing only the commands activated by a button press on the cradle. Slide the button
to the right position to turn off the feature and unblock the remote, allowing communication between the
furniture and remote.
To Use the Find Me:
Use this feature to locate a misplaced or lost remote.
Press and release the Find Me button on the cradle to send a signal to the remote. When the signal reaches the
remote, the remote LED lights start flashing and a loud tone plays continuously from the remote for two minutes,
or until any key is pressed on the remote. A key press on the remote when in Find Me mode does not produce
any movement, it only clears the Find Me response.
You can also clear the Find Me mode by pressing the Find Me button a second time, within two minutes of the
first press.
The Find Me mode is always enabled and works regardless if the Do Not Disturb feature is turned on or off.
Find Me mode is also enabled when the furniture is operating on the 9-volt battery back-up in the power supply,
or the optional rechargeable lithium-ion battery pack.
NOTE: For the Find Me feature to operate, the furniture must be powered, working batteries properly installed in
the remote and the remote within range of the furniture.
To Use the USB Charging Port:
Plug the USB cable of a small portable electronic device into the USB charging port. Unplug the USB cable
from the charging port when charging is complete. The USB port is for charging only and does not save or
transfer data.
NOTE: When the furniture is operating on the 9-volt battery back-up in the power supply, the USB charge port is
disabled. When the furniture is powered by the optional rechargeable lithium-ion battery pack, the USB port
is enabled, as long as there is adequate charge.
37
36
Troubleshooting
Troubleshooting the Legrest Operation
If the legrest stops moving while closing, it may have encountered an obstruction.
1. Check to make sure there are no obstructions. Lift and hold the legrest up, look for obstructions
and remove them.
2. The legrest uses spring tension to close, and will close quickly when the obstruction is removed. Release
the legrest slowly to prevent it from slamming shut.
Troubleshooting the Power Motion Sofa, Chair & Modular with Headrest and Lumbar
1. Make sure the 120 volt power cord is plugged into an electrical outlet.
2. Check the power supply to make sure the green LED power indicator light is on.
3. Make sure the electrical outlet is working. For example, make sure there are no blown fuses or tripped circuit
breakers. If you are unsure of the outlet’s condition, check with a qualified electrician.
4. Make sure all the connectors are secure; refer to the Assembly Instructions.
5. Make sure the electrical cords are not crimped or pinched. Make sure the electric cord or plug is not damaged.
6. Make sure the operating capacity has not been exceeded and there is only one occupant in the individual
seat or unit; refer to the Operating Instructions.
Power Supply Replacement
If the power supply must be replaced:
1. Unplug the power supply from the electrical outlet.
2. Unplug the 120 volt power cord from the electrical outlet and disconnect the power supply from either the
Y-cable or motor connector, whichever comes with the product; refer to the Assembly Instructions.
3. Connect the new power supply to the motor connector or (Y-cable), and close the locking cover when
applicable. Connect the 120 volt power cord to the new power supply; refer to the Assembly Instructions.
4. Install two fresh, name brand (Duracell/Energizer), 9-volt alkaline batteries every 6 months; refer to
Battery Backup Instructions.
5. Proceed to the Battery Backup Instructions.
If the unit still does not operate properly, contact your dealer for instructions on returning the unit for
examination and repair. Except for the replacement of the power supply, never attempt to make any
repairs or adjustments yourself.
– To reduce the risk of burns, fire, electric shock,
serious injury or death:
• Never operate the unit with a damaged power supply, electrical cord, plug or connector.
Check the condition of the power supplies, electrical cords, plugs and connectors often.
• Keep the electrical cord away from heat sources.
• Power Motion Furniture with and without Headrest and Lumbar units are intended for a
single occupant not exceeding 300 pounds per seat. Do not operate an individual seat with
more than one occupant in or on any part of the individual seat.
WARNING
Troubleshooting
Troubleshooting the Memory Settings
If the Memory setting does not save and the error tone (three quick beeps) is heard after holding a memory
button, the Memory program may need to be reset.
1. Press and release the Home button. The furniture automatically moves to its Home position to clear and
reset its programmed baseline position, which is Home.
2. Move the furniture to the desired recline position. Press and hold a Memory button. The Memory setting
will now save and play the appropriate tone for the button pressed, which is a single or double beep.
If the furniture moves to the Home position instead of a Memory position, check the Memory setting.
1. If the Memory I or Memory II setting is not yet saved, the furniture is programmed to move to its Home
position rather than remain idle (unless it is already in the Home position).
Move the furniture to the desired recline position. Press and hold a Memory button. The Memory setting
will now save and play the appropriate tone for the button pressed, which is a single or double beep.
2. If a Memory setting is saved and the furniture moves to the Home position, there is an issue with the
furniture’s position tracking program. When the furniture completes an automatic Home drive cycle, it
clears itself and resets its position. All stored Memory settings are retained during the Home cycle.
When the Home drive is complete, press and release the Memory I or Memory II button and the furniture
moves to the stored setting.
Troubleshooting the Optional Wireless Remote
If the furniture does not respond to any button presses made from the wireless remote:
1. Make sure the Do Not Disturb button is in the off position, and not turned on.
2. Replace the batteries in the remote. Refer to the battery installation instructions on page 18.
3. Unplug the power supply from the electrical outlet. Disconnect the power supply from the motor connector.
Remove the batteries from the remote. Wait 30 seconds. Reinstall the batteries in the remote. Reconnect
the power supply to the motor connector. Plug the power supply into the electrical outlet.
39
38
– To reduce the risk of serious injury:
• Provide a clear path for operation of the back and legrest. Place tables and area rugs
at a distance to allow the legrest to fully extend without rubbing or interference.
WARNING
To place your reclining unit the proper distance from the wall, fully recline the unit and leave a
minimum of 2" of space between the top of the back and the wall.
Place tables and area rugs at a distance to allow the legrest to fully extend without rubbing or
interference. If necessary, raise the adjustable glides to prevent the legrest from rubbing or
interfering with area rugs; refer to the Assembly Instructions.
Furniture Placement Guide
(Page intentionally left blank)
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
dans d''autres langues
- English: La-Z-Boy U44724 User manual
- español: La-Z-Boy U44724 Manual de usuario
