Rhine Electronics 7262T6 Ceiling Fan Controller Manuel utilisateur

7262T6 Ceiling Fan Controller
Rhine Electronics
Marque
Rhine Electronics
Modèle
7262T6 Ceiling Fan Controller
Taper
Manuel utilisateur
1/4
INSTRUCTIONS FOR OPERATION
SETING THE OPERATING CONTROLS
1.This unit operates on AAA*2PCS.; 3 volts battery (not included).
To prevent possible damage if the battery should leak, be sure to remove
the battery when the unit is not use.
2. Store the controller away from excess heat or humidity.
3. This remote-control unit is required with 35bit code combinations. To prevent
possible interference from or to other remote units such as garage door
openers, car alarm or security system.
4.Operation buttons on the panel of transmitter.
key – For FAN and LIGHT ON/OFF control .
key – For UPPER LIGHT ON/OFF control .
key – For Dimming - brightening
key – For Dimming - dimming
Key - For BOTTOM LIGHT ON/OFF
key – For Light color temperature Adjustment
key – For Light RGB discoloration
key – For FAN ON/OFF control .
key –For Fan speed up control .
key –For Fan slow down control .
key –For fan natural wind speed control .
Key –For fan blowing up control .
key –For fan blowing down control .
Key - Close Fan after 2 hours
Key - Close Fan after 4 hours
Key - Close Fan after 8 hours
Key - fan learning
2/4
GENERAL INFORMATION :
This remote controller is designed to separately control your
ceiling fan speed and light brightness.
INSTRUCTIONS FOR INSTALLATION AND OPERATION OF FAN SPEED CONTROLLER
Setup for ceiling fan controller
1. Turn off the power. (In order to make sure the electricity is entirely released, please press any
button on the controller till no LED display showing)
2. Turn on the power
3. Press the FAN OFF button for more than 3 sec. The ceiling fan controller will have 2 blinks. It
means the setup is successful. You could start to control the ceiling fan light and fan speed.
NOTICE:
The changes or modifications not expressly approved by the
party responsible for compliance could void user’s authority
to operate the equipment.
3/4
IMPORTANT NOTE: To comply with the FCC RF exposure compliance requirements, no change to
the antenna or the device is permitted. Any change to the antenna or the device could result in the
device exceeding the RF exposure requirements and void user’s authority to operate the device.
FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/ TV technician for help.
CAUTION:
Any changes or modifications not expressly approved by the grantee of this device could void the user's
authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept any
interference
received, including interference that may cause
4/4
Canada, Industry Canada (IC) Notices
This device complies with Canada license‐exempt RSS standard(s).
Operation is subject to the following two conditions: (1) this device may not cause
interference, and (2) this device must accept any interference, including interference
that may cause undesired operation of the device.
Canada, Avis’s industry Canada (IC)
Cet appareil est conforme avec Industrie Canada exemptes de licence RSS
standard(s).
Son fonctionnement est soumis aux deux conditions suivantes : (1) cet appareil ne
doit pas causer d'interférence et (2) cet appareil doit accepter toute interférence,
notamment les interférences qui peuvent affecter son fonctionnement.
Radio Frequency (RF) Exposure Information
The radiated output power of the Wireless Device is below the Industry Canada (IC)
radio frequency exposure limits. The Wireless Device should be used in such a
manner such that the potential for human contact during normal operation is
minimized.
This device has also been evaluated and shown compliant with the IC RF Exposure
limits under portable exposure conditions.
Information concernant l'exposition aux fréquences radio (RF)
La puissance de sortie émise par l’appareil de sans fil est inférieure à la limite
d'exposition aux fréquences radio d'Industry Canada (IC). Utilisez l’appareil de sans
fil de façon à minimiser les contacts humains lors du fonctionnement normal.
Ce périphérique a également été évalué et démontré conforme aux limites
d'exposition aux RF d'IC dans des conditions d'exposition à des appareils portables.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Rhine Electronics 7262T6 Ceiling Fan Controller Manuel utilisateur

7262T6 Ceiling Fan Controller
Rhine Electronics
Marque
Rhine Electronics
Modèle
7262T6 Ceiling Fan Controller
Taper
Manuel utilisateur
Télécharger le PDF
rapport

dans d''autres langues

Autres documents