GREE GRJWB05-J2 Manuel utilisateur

Taper
Manuel utilisateur
WIFI+BLE module Manual
Model: GRJWB05-J2 FCC ID2ADAP-GRJWB05J2 IC12478A-GRJWB05J2
Gree Electric Appliances, Inc. of Zhuhai
Please read this manual carefully before operation and keep it well for future reference.
Due to product improvement, Gree reserves the right to change contents of this manual without prior notice.
Gree Electric Appliances, Inc. of Zhuhai reserves the final right to interpret this manual.
WiFi Module User
Manual
1
1、General Functions
The wireless module complies with IEEE 802.11 a/b/g/n standard
and it can achieve up to a speed of 65Mbps with single stream in
802.11n , 54Mbps as specified in IEEE 802.11a/g, or 11Mbps for IEEE
802.11b to connect to the wireless LAN.This compact module is a total
solution for a combination of Wi-Fi 802.11 a/b/g/n technologies with
Microcontroller Processor. The main control chip of this module is
highly integrated with Bluetooth low-power controller, with UART
interface. It combines Bluetooth protocol, BLE baseband, MODEM and
BLE RF-IN chips. It also supports GATT-based applications and MESH
device applications based on BLE users, and supports Bluetooth 5.0
low power consumption.
This compact module is a total solution for a combination of Wi-Fi
802.11a/b/g/n technologies with Microcontroller Processor. The
module is specifically developed for embedded system devices.
Detailed Instruction of WiFi Module.
WiFi Module User
Manual
2
2、Technique Parameters
Table1. Module Parameters
Categories
Feature
parameters
Wireless
specification
Operating
Bands
2.4G:
FCC:2412 MHz to 2462 MHz for 802.11 b/g/n(HT40)
RED:2412MHz to 2472 MHz for 802.11b/g/n(HT40)
2402MHz to 2480 MHz for BLE
5G:
5810 MHz to 5825 MHz for 802.11 a/g/n(HT40)
Protocol
IEEE 802.11 a/b/g/n
frequency
modulation
mode
CCKOFDMGFSK
Receive
Sensitivity
802.11b<-90.5dBm@11Mbps
802.11a/g<-77.5dBm@54Mbps
802.11n<-72dBm@MCS7
Data Rate
WIFI:
802.11b1/2/5.5/11 Mbps
802.11a/g6/9/12/18/24/36/48/54 Mbps
802.11n(HT20):6.5/13/19.5/26/39/52/58.5/65 Mbps
802.11n(HT40):13.5/27/40.5/54/81/108/121.5/135Mbps
BLE rate: 1 Mbps
Antenna
gain max
1.5 dBi
WiFi Module User
Manual
3
Impedance
50-Ohm
electrical
specification
Supply
Voltage
+3.3V
Connect
Internal Antenna
physical
Dimensions
37mm×17.7mm±0.2mm
Operating
Temperature
--
-20-85 deg C.
3、Circuit Description
Figure1. Circuit Diagram
WIFI module has an independent power management system, and
the system provides a high quality of power supply for the whole
module. The Excellent matching circuit in RF-Front ensures that the
WiFi Module User
Manual
4
signal has minimal signal loss and radiation. Oscillator Y1 provides the
IC U4 with the required oscillation frequency to enable the IC U4 to
work normally.Flash U2 is used for the external expansion memory.The
duplexer isolates the transmitting and receiving signals to ensure that
the receiving and transmitting can work normally at the same time.The
IC U4 provides the interfaces for a variety of peripherals (Timer, PWM,
Interrupt, AD, the Debug) from the module to the baseboard. Each
peripheral that connects to the MCU I/O pins can choose between two
different I/O pin locations with the provided flexibility in various
applications
Hereby, [Name of manufacturer], declares that this [type of
equipment] is in compliance with the essential requirements and other
relevant provisions of RE Directive 2014/53/EU. A copy of the full DoC
is attached.
Transmit frequency of EU:
WIFI: 2412-2472MHz / 5180-5825MHz
BLE: 2402-2480MHz
Maximum transmit power: <20dBm
4、Pin Definition
WiFi Module User
Manual
5
Figure2. Pin Definition
Table2. Pin Definition
PIN
Name
Mode
2,13
VCC
+3.3V
4
TX
UART_TX
5
RX
UART_RX
1,14
GND
Ground
9
RX
LOG_RX
8
TX
LOG_TX
11
I2C_SCL
I2C_SCL
10
I2C_SDA
I2C_SDA
12
I2S_TXD
I2S_TXD
15
I2S_CLK
I2S_CLK
16
I2S_WS
I2S_WS
3
ADC
ADC
17
SPI_MOSI
SPI_MOSI
WiFi Module User
Manual
6
18
SPI_CLK
SPI_CLK
6
SPI_CS
SPI_CS
7
SPI_MISO
SPI_MISO
19
SWD_DATA
SWD_DATA
20
HS_URXD
HS_URXD
21
HS_UTXD
HS_UTXD
22
LP_PWM
LP_PWM
23
I2S_MCLK
I2S_MCLK
24
I2S_SD_RX
I2S_SD_RX
25
SWD_CLK
SWD_CLK
Caution: The user is cautioned that changes or modifications not expressly
approved by the party responsible for compliance could void the user's
authority to operate the equipment.
Second label must be place on the outside of the final device that contains
the following text:
“Contains FCC ID: 2ADAP-GRJWB05J2
“Contains IC: 12478A-GRJWB05J2
The FCC ID/IC ID can be used only when all FCC/IC compliance
requirements are met.
This device complies with Part 15 of the FCC Rules and it contains licence-
exempt transmitter(s)/receiver(s) that comply with Innovation, Science and
Economic Development Canada’s licence-exempt RSS(s). Operation is
subject to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables
aux appareils radio exempts de licence. L’exploitation est autorisée aux deux
conditions suivantes :
(1) l’appareil ne doit pas produire de brouillage, et
(2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi,
même si le brouillage est susceptible d’en compromettre le fonctionnement.
WiFi Module User
Manual
7
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help.
FCC& IC Radiation Exposure Statement:
This equipment complies with FCC and Canada radiation exposure limits set forth for
an uncontrolled environment. This equipment should be installed and operated with a
minimum distance of 20cm between the radiator and your body.
This transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter.
Déclaration d’IC sur l’exposition aux radiations:
Cet équipement est conforme aux limites d’exposition aux radiations définies
par le Canada pour des environnements non contrôlés. Cet équipement doit
WiFi Module User
Manual
8
être installé et utilisé à une distance minimum de 20 cm entre l’antenne et votre
corps.
Cet émetteur ne doit pas être installé au même endroit ni utilisé avec une autre
antenne ou un autre émetteur.
Gree Electric AppliancesInc. of Zhuhai
Adresse:West Jinji Rd,Qianshan,Zhuhai,Guangdong,China, 519070
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10

GREE GRJWB05-J2 Manuel utilisateur

Taper
Manuel utilisateur

dans d''autres langues