Hitachi WH 18DBFL2 Manuel utilisateur

Marque: Hitachi

Modèle: WH 18DBFL2

Catégorie: Perceuses mixtes sans fil

Taper: Manuel utilisateur

Designed for operating in USA & Canada only.

When this product is used in areas other than the USA & Canada,

we cannot guarantee the product quality and performance.

SAFETY INSTRUCTIONS AND INSTRUCTION MANUAL

WARNING

IMPROPER OR UNSAFE use of this power tool can result in death or serious bodily injury!

This manual contains important information about product safety. Please read and understand

this manual BEFORE operating the power tool. Please keep this manual available for other

users and owners before they use the power tool. This manual should be stored in safe place.

INSTRUCTIONS DE SECURITE ET MODE D’EMPLOI

AVERTISSEMENT

Une utilisation INCORRECTE OU DANGEREUSE de cet outil motorisé peut entraîner la mort

ou de sérieuses blessures corporelles!

Ce mode d’emploi contient d’importantes informations à propos de la sécurité de ce produit.

Prière de lire et de comprendre ce mode d’emploi AVANT d’utiliser l’outil motorisé. Garder ce

mode d’emploi à la disponibilité des autres utilisateurs et propriétaires avant qu’ils utilisent

l’outil motorisé. Ce mode d’emploi doit être conservé dans un endroit sûr.

INSTRUCCIONES DE SEGURIDAD Y MANUAL DE INSTRUCCIONES

ADVERTENCIA

¡La utilización INAPROPIADA O PELIGROSA de esta herramienta eléctrica puede resultar

en lesiones de gravedad o la muerte!

Este manual contiene información importante sobre la seguridad del producto. Lea y

comprenda este manual ANTES de utilizar la herramienta eléctrica. Guarde este manual para

que puedan leerlo otras personas antes de utilizar la herramienta eléctrica. Este manual debe

ser guardado en un lugar seguro.

Model

Modèle

Modelo

WH 18DBFL2

Cordless Impact Driver

Marteau à choc sans ﬁ l

Atornillador de impacto inalámbrico

English

Page Page

Français

Page Page

Español

Página Página

TABLE DES MATIÈRES

ÍNDICE

CONTENTS

IMPORTANT SAFETY INFORMATION ..................... 3

MEANINGS OF SIGNAL WORDS ............................ 3

SAFETY........................................................................ 3

GENERAL POWER TOOL SAFETY WARNINGS ...... 3

SPECIFIC SAFETY RULES AND SYMBOLS ............ 5

IMPORTANT SAFETY INSTRUCTIONS

FOR USE OF THE CORDLESS IMPACT

DRIVER .............................................................. 6

IMPORTANT SAFETY INSTRUCTIONS

FOR BATTERY CHARGER ................................ 6

IMPORTANT SAFETY INSTRUCTIONS

FOR USE OF THE BATTERY AND

BATTERY CHARGER ......................................... 7

CAUTION ON LITHIUM-ION BATTERY ..................... 7

REGARDING LITHIUM-ION BATTERY

TRANSPORTATION ........................................... 8

FUNCTIONAL DESCRIPTION .................................... 9

NAME OF PARTS ..................................................... 9

SPECIFICATIONS ................................................... 10

ASSEMBLY AND OPERATION ................................. 11

APPLICATIONS ...................................................... 11

REMOVAL AND INSTALLATION METHOD

OF BATTERY ................................................... 11

CHARGING METHOD ............................................. 11

BEFORE USE ......................................................... 13

OPERATION ........................................................... 13

OPERATIONAL CAUTIONS .................................... 15

MAINTENANCE AND INSPECTION ......................... 16

TROUBLESHOOTING GUIDE ................................... 17

ACCESSORIES ......................................................... 18

STANDARD ACCESSORIES .................................. 18

OPTIONAL ACCESSORIES…sold separately ........ 19

PARTS LIST ............................................................... 58

INFORMATIONS IMPORTANTES DE SÉCURITÉ ... 20

SIGNIFICATION DES MOTS D’AVERTISSEMENT ... 20

SECURITE ................................................................. 20

AVERTISSEMENTS DE SÉCURITÉ GÉNÉRAUX

CONCERNANT LES OUTILS ÉLECTRIQUES ... 20

REGLES DE SECURITE SPECIFIQUES

ET SYMBOLES ................................................ 22

CONSIGNES DE SÉCURITÉ IMPORTANTES POUR

L'UTILISATION DU MARTEAU À CHOC SANS

FIL .................................................................. 23

CONSIGNES DE SÉCURITÉ IMPOR TANTES

POUR LE CHARGEUR DE BATTERIE ............. 23

CONSIGNES DE SÉCURITÉ IMPORTANTES POUR

L’UTILISATION DE LA BATTERIE ET

DU CHARGEUR DE BATTERIE ....................... 24

PRÉCAUTIONS RELATIVES A LA BATTERIE AU

LITHIUM ION .................................................... 25

À PROPOS DU TRANSPORT DE LA BATTERIE

LITHIUM-ION ................................................... 26

DESCRIPTION FONCTIONNELLE ........................... 27

NOM DES PARTIES ................................................ 27

SPECIFICATIONS ................................................... 28

ASSEMBLAGE ET FONCTIONNEMENT .................. 29

UTILISATIONS ......................................................... 29

MÉTHODE DE RETRAIT ET D’INSTALLATION

DE LA BATTERIE ............................................. 29

MÉTHODE DE RECHARGE .................................... 29

AVANT L’UTILISATION............................................. 31

UTILISATION ........................................................... 31

PRECAUTIONS D'UTILISATION ............................. 34

ENTRETIEN ET INSPECTION .................................. 35

GUIDE DE DÉPANNAGE .......................................... 36

ACCESSOIRES ......................................................... 37

ACCESSOIRES STANDARD ................................... 37

ACCESSOIRES EN OPTION...vendus séparément ...38

LISTE DES PIECES ................................................... 58

INFORMACIÓN IMPORTANTE SOBRE

SEGURIDAD .................................................... 39

SIGNIFICADO DE LAS PALABRAS DE

SEÑALIZACIÓN ............................................... 39

SEGURIDAD .............................................................. 39

ADVERTENCIAS DE SEGURIDAD GENERAL

DE LA HERRAMIENTA ELÉCTRICA ................ 39

NORMAS Y SÍMBOLOS ESPECÍFICOS DE

SEGURIDAD .................................................... 41

INSTRUCCIONES IMPORTANTES PARA LA

UTILIZACIÓN DEL ATORNILLADOR DE

IMPACTO INALÁMBRICO ................................ 42

INSTRUCCIONES IMPORTANTES DE

SEGURIDAD PARA EL CARGADOR

DE BATERÍAS .................................................. 43

INSTRUCCIONES IMPORTANTES DE

SEGURIDAD PARA LA BATERÍA Y

EL CARGADOR DE BATERÍAS ........................ 44

ADVERTENCIA DE LA BATERÍA DE LITIO ............. 44

A PROPÓSITO DEL TRANSPORTE DE LA

BATERÍA DE IONES DE LITIO ......................... 45

DESCRIPCIÓN FUNCIONAL .................................... 46

NOMENCLATURA ................................................... 46

ESPECIFICACIONES .............................................. 47

MONTAJE Y OPERACIÓN ........................................ 48

APLICACIONES ...................................................... 48

MÉTODO DE EXTRACCIÓN E INSTALACIÓN

DE LA BATERÍA ............................................... 48

MÉTODO DE CARGA .............................................. 48

ANTES DE LA UTILIZACIÓN ................................... 50

OPERACIÓN ........................................................... 50

PRECAUCIONES OPERACIONALES ..................... 53

MANTENIMIENTO E INSPECCIÓN .......................... 54

GUIA DE IDENTIFICACION DE PROBLEMAS ........ 55

ACCESSORIOS ......................................................... 56

ACCESORIOS ESTÁNDAR ..................................... 56

ACCESORIOS OPCIONALES...

de venta por separado ...................................... 57

LISTA DE PIEZAS ..................................................... 58

IMPORTANT SAFETY INFORMATION

Read and understand all of the safety precautions, warnings and operating instructions in the Instruction Manual before

operating or maintaining this power tool.

Most accidents that result from power tool operation and maintenance are caused by the failure to observe basic safety

rules or precautions. An accident can often be avoided by recognizing a potentially hazardous situation before it occurs,

and by observing appropriate safety procedures.

Basic safety precautions are outlined in the “SAFETY” section of this Instruction Manual and in the sections which

contain the operation and maintenance instructions.

Hazards that must be avoided to prevent bodily injury or machine damage are identiﬁ ed by WARNINGS on the power

tool and in this Instruction Manual.

NEVER use this power tool in a manner that has not been speciﬁ cally recommended by HITACHI.

MEANINGS OF SIGNAL WORDS

WARNING indicates a potentially hazardous situations which, if ignored, could result in death or serious injury.

CAUTION indicates a potentially hazardous situations which, if not avoided, may result in minor or moderate injury, or

may cause machine damage.

NOTE emphasizes essential information.

SAFETY

GENERAL POWER TOOL SAFETY WARNINGS

WARNING

Read all safety warnings and all instructions.

Failure to follow the warnings and instructions may result in electric shock, ﬁ re and/or serious injury.

Save all warnings and instructions for future reference.

The term “power tool” in the warnings refers to your mains-operated (corded) power tool or battery-operated

(cordless) power tool.

1) Work area safety

a) Keep work area clean and well lit.

Cluttered or dark areas invite accidents.

b) Do not operate power tools in explosive

atmospheres, such as in the presence of

ﬂ ammable liquids, gases or dust.

Power tools create sparks which may ignite the

dust or fumes.

c) Keep children and bystanders away while

operating a power tool.

Distractions can cause you to lose control.

2) Electrical safety

a) Power tool plugs must match the outlet.

Never modify the plug in any way.

Do not use any adapter plugs with earthed

(grounded) power tools.

Unmodiﬁ ed plugs and matching outlets will reduce

risk of electric shock.

b) Avoid body contact with earthed or grounded

surfaces such as pipes, radiators, ranges and

refrigerators.

There is an increased risk of electric shock if your

body is earthed or grounded.

c) Do not expose power tools to rain or wet

conditions.

Water entering a power tool will increase the risk

of electric shock.

d) Do not abuse the cord. Never use the cord

for carrying, pulling or unplugging the power

tool.

Keep cord away from heat, oil, sharp edges or

moving parts.

Damaged or entangled cords increase the risk of

electric shock.

e) When operating a power tool outdoors, use

an extension cord suitable for outdoor use.

Use of a cord suitable for outdoor use reduces the

risk of electric shock.

f) If operating a power tool in a damp location

is unavoidable, use a residual current device

(RCD) protected supply.

Use of an RCD reduces the risk of electric shock.

English

3) Personal safety

a) Stay alert, watch what you are doing and use

common sense when operating a power tool.

Do not use a power tool while you are tired

or under the inﬂ uence of drugs, alcohol or

medication.

A moment of inattention while operating power

tools may result in serious personal injury.

b) Use personal protective equipment. Always

wear eye protection.

Protective equipment such as dust mask, non-skid

safety shoes, hard hat, or hearing protection used

for appropriate conditions will reduce personal

injuries.

c) Prevent unintentional starting. Ensure the

switch is in the oﬀ -position before connecting

to power source and/or battery pack, picking

up or carrying the tool.

Carrying power tools with your ﬁ nger on the switch

or energising power tools that have the switch on

invites accidents.

d) Remove any adjusting key or wrench before

turning the power tool on.

A wrench or a key left attached to a rotating part of

the power tool may result in personal injury.

e) Do not overreach. Keep proper footing and

balance at all times.

This enables better control of the power tool in

unexpected situations.

f) Dress properly. Do not wear loose clothing or

jewellery. Keep your hair, clothing and gloves

away from moving parts.

Loose clothes, jewellery or long hair can be caught

in moving parts.

g) If devices are provided for the connection

of dust extraction and collection facilities,

ensure these are connected and properly

used.

Use of dust collection can reduce dust-related

hazards.

4) Power tool use and care

a) Do not force the power tool. Use the correct

power tool for your application.

The correct power tool will do the job better and

safer at the rate for which it was designed.

b) Do not use the power tool if the switch does

not turn it on and oﬀ .

Any power tool that cannot be controlled with the

switch is dangerous and must be repaired.

c) Disconnect the plug from the power source

and/or the battery pack from the power tool

before making any adjustments, changing

accessories, or storing power tools.

Such preventive safety measures reduce the risk

of starting the power tool accidentally.

d) Store idle power tools out of the reach of

children and do not allow persons unfamiliar

with the power tool or these instructions to

operate the power tool.

Power tools are dangerous in the hands of

untrained users.

e) Maintain power tools. Check for misalignment

or binding of moving parts, breakage of parts

and any other condition that may aﬀ ect the

power tool’s operation.

If damaged, have the power tool repaired

before use.

Many accidents are caused by poorly maintained

power tools.

f) Keep cutting tools sharp and clean.

Properly maintained cutting tools with sharp

cutting edges are less likely to bind and are easier

to control.

g) Use the power tool, accessories and tool bits

etc. in accordance with these instructions,

taking into account the working conditions

and the work to be performed.

Use of the power tool for operations diﬀ erent

from those intended could result in a hazardous

situation.

5) Battery tool use and care

a) Recharge only with the charger speciﬁ ed by

the manufacturer.

A charger that is suitable for one type of battery

pack may create a risk of ﬁ re when used with

another battery pack.

b) Use power tools only with speciﬁ cally

designated battery packs.

Use of any other battery packs may create a risk of

injury and ﬁ re.

c) When battery pack is not in use, keep it away

from other metal objects like paper clips,

coins, keys, nails, screws, or other small

metal objects, that can make a connection

from one terminal to another.

Shorting the battery terminals together may cause

burns or a

ﬁ re.

d) Under abusive conditions, liquid may be

ejected from the battery; avoid contact. If

contact accidentally occurs, ﬂ ush with water.

If liquid contacts eyes, additionally seek

medical help.

Liquid ejected from the battery may cause irritation

or burns.

6) Service

a) Have your power tool serviced by a

qualiﬁ ed repair person using only identical

replacement parts.

This will ensure that the safety of the power tool is

maintained.

English

8. Use right tool.

Don’t force small tool or attachment to do the job of a

heavy-duty tool.

Don’t use tool for purpose not intended —for

example— don’t use circular saw for cutting tree

limbs or logs.

9. NEVER use a power tool for applications other

than those speciﬁ ed.

NEVER use a power tool for applications other than

those speciﬁ ed in the Instruction Manual.

10. Handle tool correctly.

Operate the tool according to the instructions provided

herein. Do not drop or throw the tool. NEVER allow the

tool to be operated by children, individuals unfamiliar

with its operation or unauthorized personnel.

11. Keep all screws, bolts and covers tightly in place.

Keep all screws, bolts, and plates tightly mounted.

Check their condition periodically.

12. Do not use power tools if the plastic housing or

handle is cracked.

Cracks in the tool’s housing or handle can lead to

electric shock. Such tools should not be used until

repaired.

13. Blades and accessories must be securely

mounted to the tool.

Prevent potential injuries to yourself or others. Blades,

cutting implements and accessories which have been

mounted to the tool should be secure and tight.

14. NEVER use a tool which is defective or operating

abnormally.

If the tool appears to be operating unusually, making

strange noises, or otherwise appears defective, stop

using it immediately and arrange for repairs by a

Hitachi authorized service center.

15. Carefully handle power tools.

Should a power tool be dropped or struck against

hard materials inadvertently, it may be deformed,

cracked, or damaged.

16. Do not wipe plastic parts with solvent.

Solvents such as gasoline, thinner benzine, carbon

tetrachloride, and alcohol may damage and crack

plastic parts. Do not wipe them with such solvents.

Wipe plastic parts with a soft cloth lightly dampened

with soapy water and dry thoroughly.

17. Always wear eye protection that meets the

requirement of the latest revision of ANSI

Standard Z87.1.

18. Deﬁ nitions for symbols used on this tool

V ............ volts

—

---

......... direct current

no .......... no load speed

---/min .... revolutions or reciprocation per minute

– WARNING –

To reduce the risk of injury, user must read

instruction manual.

WARNING

Some dust created by power sanding, sawing,

grinding, drilling, and other construction activities

contains chemicals known to the State of California

to cause cancer, birth defects or other reproductive

harm. Some examples of these chemicals are:

●

Lead from lead-based paints,

●

Crystalline silica from bricks and cement and

other masonry products, and

●

Arsenic and chromium from chemically-treated

lumber.

Your risk from these exposures varies, depending on

how often you do this type of work. To reduce your

exposure to these chemicals: work in a well ventilated

area, and work with approved safety equipment, such

as those dust masks that are specially designed to

ﬁ lter out microscopic particles.

SPECIFIC SAFETY RULES AND SYMBOLS

1. Hold power tools by insulated gripping surfaces,

when performing an operation where the

fastener may contact hidden wiring.

Fasteners contacting a “live” wire may make exposed

metal parts of the power tool “live” and could give the

operator an electric shock.

2. ALWAYS wear ear protectors when using the tool

for extended periods.

Prolonged exposure to high intensity

noise can cause hearing loss.

3. NEVER place hands or other body parts near the drill

bit or chuck during operation. Hold the impact driver

by its handle only.

Because the cordless impact driver operates by

battery power, be aware of the fact that it can begin to

operate at any time.

5. When working at elevated locations, clear the area

of all other people and be aware of conditions below

you.

6. NEVER touch moving parts.

NEVER place your hands, ﬁ ngers or other body parts

near the tool’s moving parts.

7. NEVER operate without all guards in place.

NEVER operate this tool without all guards or safety

features in place and in proper working order. If

maintenance or servicing requires the removal of a

guard or safety feature, be sure to replace the guard or

safety feature before resuming operation of the tool.

English

IMPORTANT SAFETY INSTRUCTIONS

FOR USE OF THE CORDLESS IMPACT

DRIVER

WARNING

Death or serious bodily injury could result from

improper or unsafe use of the cordless impact

driver. To avoid these risks, follow these basic

safety instructions:

1. NEVER use this impact driver handle for any

application other than those in this manual.

2. NEVER place hands or other body parts near the drill

bit or chuck during operation.

Hold the impact driver by its handle only.

3. When working in high places, always make sure that

ther is no one below before starting to work.

4. ALWAYS wear eye and ear protection when you work.

5. ALWAYS install the driver bit securely. A loose bit is

dangerous because it can come loose while you are

working.

6. ALWAYS use the driver bit that matches the screw

size.

7. ALWAYS have the screw you are screwing in and

this impact driver in a straight line. Working with this

impact driver at an angle to the screw can damage the

screw head and will not give the prescribed tightening

torque.

IMPORTANT SAFETY INSTRUCTIONS

FOR BATTERY CHARGER

WARNING

Death or serious bodily injury could result from

improper or unsafe use of battery chargers.

To avoid these risks, follow these basic safety

instructions:

READ ALL INSTRUCTIONS

1. This manual contains important safety and operating

instructions for battery charger Model UC18YKSL.

2. Before using battery charger, read all instructions

and cautionary markings on (1) battery charger, (2)

battery, and (3) product using battery.

3. To reduce risk of injury, charge HITACHI rechargeable

battery type BSL18 series. Other type of batteries

may burst causing personal injury and damage.

4. Do not expose battery charger to rain or snow.

5. Use of an attachment not recommended or sold by

the battery charger manufacturer may result in a risk

of ﬁ re, electric shock, or injury to persons.

6. To reduce risk of damage to electric plug and cord,

pull by plug when disconnecting battery charger.

7. Make sure cord is located so that it will not be stepped

on, tripped over, or otherwise subjected to damage or

stress.

8. An extension cord should not be used unless

absolutely necessary. Use of improper extension

cord could result in a risk of ﬁ re and electric shock.

If extension cord must be used make sure:

a. That blades of extension cord are the same

number, size, and shape as those of plug on

battery charger:

b. That extension cord is properly wired and in good

electrical condition; and

c. That wire size is large enough for AC ampere

rating of battery charger as speciﬁ ed in Table 1.

Table 1

RECOMMENDED MINIMUM AWG SIZE FOR

EXTENSION CORDS FOR BATTERY CHARGERS

AC Input Rating Amperes* AWG Size of Cord

Equal to or

greater than

but less

than

Length of Cord, Feet (Meter)

25 (7.5) 50 (15) 100 (30) 150 (45)

0 2 18 18 18 16

2 3 18 18 16 14

3 4 18 18 16 14

* If the input rating of a battery charger is given in watts rather than in amperes, the corresponding ampere rating is to

be determined by dividing the wattage rating by the voltage rating–for example:

1,250 watts

= 10 amperes

125 volts

English

11. NEVER store the battery or battery charger in places

where the temperature may reach or exceed 104°F

(40°C).

12. ALWAYS operate charger on standard household

electrical power (120 volts). Using the charger on any

other voltage may overheat and damage the charger.

13. ALWAYS wait at least 15 minutes between charges to

avoid overheating the charger.

14. ALWAYS disconnect the power cord from its

receptacle when the charger is not in use.

CAUTION ON LITHIUM-ION BATTERY

To extend the lifetime, the lithium-ion battery equips with

the protection function to stop the output.

In the cases of 1 to 3 described below, when using this

product, even if you are pulling the switch, the motor may

stop. This is not the trouble but the result of protection

function.

1. When the battery power remaining runs out, the motor

stops.

In such case, charge it up immediately.

2. If the tool is overloaded, the motor may stop. In this

case, release the switch of tool and eliminate causes

of overloading. After that, you can use it again.

3. If the battery is overheated under overload work, the

battery power may stop.

In this case, stop using the battery and let the battery

cool. After that, you can use it again.

Furthermore, please heed the following warning and

caution.

WARNING

In order to prevent any battery leakage, heat generation,

smoke emission, explosion and ignition beforehand,

please be sure to heed the following precautions.

1. Make sure that swarf and dust do not collect on the

battery.

○

During work make sure that swarf and dust do not fall

on the battery.

○

Make sure that any swarf and dust falling on the power

tool during work do not collect on the battery.

○

Do not store an unused battery in a location exposed

to swarf and dust.

○

Before storing a battery, remove any swarf and dust

that may adhere to it and do not store it together with

metal parts (screws, nails, etc.).

2. Do not pierce battery with a sharp object such as a

nail, strike with a hammer, step on, throw or subject

the battery to severe physical shock.

3. Do not use an apparently damaged or deformed

battery.

4. Do not use the battery in reverse polarity.

5. Do not connect directly to an electrical outlets or car

cigarette lighter sockets.

9. Do not operate battery charger with damaged cord or

plug-replace them immediately.

10. Do not operate battery charger if it has received a

sharp blow, been dropped, or otherwise damaged in

any way; take it to a qualiﬁ ed serviceman.

11. Do not disassemble battery charger; take it to a

qualiﬁ ed serviceman when service or repair is

required. Incorrect reassembly may result in a risk of

electric shock or ﬁ re.

12. To reduce risk of electric shock, unplug charger from

receptacle before attempting any maintenance or

cleaning. Removing the battery will not reduce this

risk.

IMPORTANT SAFETY INSTRUCTIONS

FOR USE OF THE BATTERY AND

BATTERY CHARGER

You must charge the battery before you can use the power

tool. Before using the model UC18YKSL battery charger,

be sure to read all instructions and cautionary statements

on it, the battery and in this manual.

CAUTION

USE ONLY HITACHI BATTERY TYPES BSL18

SERIES. OTHER TYPES OF BATTERIES MAY

BURST AND CAUSE INJURY!

Follow these instructions to avoid the risk of injury:

WARNING:

Improper use of the battery

or battery charger can lead to

serious injury. To avoid these

injuries:

1. NEVER disassemble the battery.

2. NEVER incinerate the battery, even if it is damaged or

is completely worn out. The battery can explode in a

ﬁ re.

3. NEVER short-circuit the battery.

4. NEVER insert any objects into the battery charger’s

air vents. Electric shock or damage to the battery

charger may result.

5. NEVER charge outdoors. Keep the battery away

from direct sunlight and use only where there is low

humidity and good ventilation.

6. NEVER charge when the temperature is below 32°F

(0°C) or above 104°F (40°C).

7. NEVER connect two battery chargers together.

8. NEVER insert foreign objects into the hole for the

battery or the battery charger.

9. NEVER use a booster transformer when charging.

10. NEVER use an engine generator or DC power to

charge.

English

6. Do not use the battery for a purpose other than those

speciﬁ ed.

7. If the battery charging fails to complete even when a

speciﬁ ed recharging time has elapsed, immediately

stop further recharging.

8. Do not put or subject the battery to high temperatures

or high pressure such as into a microwave oven,

dryer, or high pressure container.

9. Keep away from ﬁ re immediately when leakage or foul

odor are detected.

10. Do not use in a location where strong static electricity

generates.

11. If there is battery leakage, foul odor, heat generated,

discolored or deformed, or in any way appears

abnormal during use, recharging or storage,

immediately remove it from the equipment or battery

charger, and stop use.

CAUTION

1. If liquid leaking from the battery gets into your eyes,

do not rub your eyes and wash them well with fresh

clean water such as tap water and contact a doctor

immediately.

If left untreated, the liquid may cause eye-problems.

2. If liquid leaks onto your skin or clothes, wash well with

clean water such as tap water immediately.

There is a possibility that this can cause skin irritation.

3. If you ﬁ nd rust, foul odor, overheating, discolor,

deformation, and/or other irregularities when using

the battery for the ﬁ rst time, do not use and return it to

your supplier or vendor.

WARNING

If an electrically conductive foreign object enters the

terminals of the lithium ion battery, a short-circuit may

occur resulting in the risk of ﬁ re. Please observe the

following matters when storing the battery.

○

Do not place electrically conductive cuttings,

nails, steel wire, copper wire or other wire in the

storage case.

○

Either install the battery in the power tool or store

by securely pressing into the battery cover until

the ventilation holes are concealed to prevent

short-circuits (See Fig. 3).

REGARDING LITHIUM-ION BATTERY

TRANSPORTATION

When transporting a lithium-ion battery, please observe

the following precautions.

WARNING

Notify the transporting company that a package

contains a lithium-ion battery, inform the company

of its power output and follow the instructions of the

transportation company when arranging transport.

●

Lithium-ion batteries that exceed a power output

of 100Wh are considered to be in the freight

classiﬁ cation of Dangerous Goods and will

require special application procedures.

●

For transportation abroad, you must comply with

international law and the rules and regulations of

the destination country.

Power Output

2 to 3 digit number

Fig. 1

SAVE THESE INSTRUCTIONS

AND

MAKE THEM AVAILABLE TO OTHER USERS

AND

OWNERS OF THIS TOOL!

English

FUNCTIONAL DESCRIPTION

NOTE

The information contained in this Instruction Manual is designed to assist you in the safe operation and maintenance

of the power tool.

NEVER operate, or attempt any maintenance on the tool unless you have ﬁ rst read and understood all safety

instructions contained in this manual.

Some illustrations in this Instruction Manual may show details or attachments that diﬀ er from those on your own

power tool.

NAME OF PARTS

1. Cordless Impact Driver (WH18DBFL2)

Hammer case

Guide sleeve

Pushing button

Switch trigger

Switch panel

Housing

Battery

Hook

Handle

LED Light

Fig. 2

2. Battery 3. Battery Charger

Battery

Latch

Ventilation holes

Terminals

Battery cover

Battery

Latch

Ventilation holes

Terminals

Battery cover

Body

Cord

Nameplate

Guide rail

Pilot lamp

Fig. 3

Fig. 4

English

SPECIFICATIONS

1. Cordless Impact Driver

Model WH18DBFL2

No-load speed 0 – 3,100 /min

Capacity

Small screw 5/32" (M4) – 5/16" (M8)

Ordinary bolt 3/16" (M5) – 5/8" (M16)

High tension bolt 3/16" (M5) – 15/32" (M12)

Tightening torque

Maximum 1,522 in-lbs {172 N∙m 1,754 kgf∙cm}

Tightening is 5/8" (M16) high tension bolt, when fully

charged at 68°F (20°C) temp.

Tightening time: 3 sec.

Bit shank size 1/4" (6.35 mm) Hex.

Battery

Model BSL1815 (1.5 Ah) BSL1830C (3.0 Ah)

Type Li-ion battery

Voltage DC 18 V

Weight 2.9 lbs. (1.3 kg)

2. Battery Charger

Model UC18YKSL

Input power source Single phase: AC 120 V 60 Hz

Charging time

(At a temperature of 68°F (20°C))

BSL1830C : Approx. 90 min

BSL1815 : Approx. 40 min

Charging voltage DC 14.4 – 18 V

Charging current DC 2.0 A

Weight 0.8 lbs. (0.35 kg)

NOTE: The charging time may vary according to temperature and power source voltage.

English

ASSEMBLY AND OPERATION

1. Insert the plug of battery charger into the receptacle.

When the plug of battery charger has been inserted

into the receptacle, pilot lamp will blink in red. (At

1-second intervals)

WARNING

Do not use the electrical cord

if damaged. Have it repaired

immediately.

2. Insert the battery to the battery charger.

Insert the battery into the battery charger as shown in

Fig. 6.

Battery

Charger

Pilot lamp

Fig. 6

3. Charging

When the battery is inserted into the battery charger,

charging will commence and the pilot lamp will light in

red. (See Table 2)

NOTE

If the pilot lamp does not light or blink in red, pull out

the plug from the receptacle and check if the battery

is properly mounted.

When the battery is fully charged, the pilot lamp

will blink in red slowly. (At 1-second intervals) (See

Table 2)

(1) Pilot lamp indication

The indications of the pilot lamp will be as shown in

Table 2, according to the condition of the charger or

the rechargeable battery.

APPLICATIONS

○

Driving and removing of machine screws, wood

screws, tapping screws, etc.

REMOVAL AND INSTALLATION METHOD

OF BATTERY

1. Battery removal

Hold the handle tightly and push the battery latch to

remove the battery (see Fig. 5).

CAUTION

Never short-circuit the battery.

2. Battery installation

Insert the battery while observing its polarities (see

Fig. 5).

Battery

Push

Pull out

Insert

Handle

Latch

Fig. 5

CHARGING METHOD

NOTE

Before plugging into the receptacle, make sure the

following points.

○

The power source voltage is stated on the nameplate.

○

The cord is not damaged.

WARNING

Do not charge at voltage higher than indicated

on the nameplate.

If charged at voltage higher than indicated on the

nameplate, the charger will burn up.

English

Table 2

Indications of the pilot lamp

Pilot lamp

(red)

Before charging Blinks

Lights for 0.5 seconds. Does not light for

0.5 seconds. (oﬀ for 0.5 seconds)

While charging Lights

Lights continuously

Charging

complete

Blinks

Lights for 0.5 seconds. Does not light for

0.5 seconds. (oﬀ for 0.5 seconds)

Overheat

standby

Blinks

Lights for 1 second. Does not light for 0.5

seconds. (oﬀ for 0.5 seconds)

Battery overheated.

Unable to charge.

(Charging will commence

when battery cools)

Charging

impossible

Flickers

Lights for 0.1 seconds. Does not light for

0.1 seconds. (oﬀ for 0.1 seconds)

Malfunction in the battery or

the charger

(2) Regarding the temperature of the rechargeable

battery.

The temperatures for rechargeable batteries are

as shown in the Table 3, and batteries that have

become hot should be cooled for a while before being

recharged.

Table 3 Recharging ranges of batteries

Rechargeable

batteries

Temperatures at which the

battery can be recharged

BSL1830C, BSL1815

32°F–122°F

(0°C–50°C)

(3) Regarding recharging time (At 68°F (20°C))

Table 4 Charging time

Charger

Battery

UC18YKSL

BSL1830C Approx. 90 min.

BSL1815 Approx. 40 min.

NOTE

The charging time may vary according to temperature

and power source voltage.

Regarding electric discharge in case of new

batteries, etc.

As the internal chemical substance of new batteries

and batteries that have not been used for an extended

period is not activated, the electric discharge might

be low when using them the ﬁ rst and second time.

This is a temporary phenomenon, and normal time

required for recharging will be restored by recharging

the batteries 2 – 3 times.

How to make the batteries perform longer

(1) Recharge the batteries before they become

completely exhausted.

When you feel that the power of the tool becomes

weaker, stop using the tool and recharge its battery.

If you continue to use the tool and exhaust the electric

current, the battery may be damaged and its life will

become shorter.

(2) Avoid recharging at high temperatures.

A rechargeable battery will be hot immediately after

use. If such a battery is recharged immediately after

use, its internal chemical substance will deteriorate,

and the battery life will be shortened. Leave the

battery and recharge it after it has cooled for a while.

CAUTION

●

When the battery charger has been continuosly

used, the battery charger will be heated, thus

constituting the cause of the failures. Once the

charging has been completed, give 15 minutes

rest until the next charging.

●

If the battery is charged while it is heated

because it has been left for a long time in a

location subject to direct sunlight or because

the battery has just been used, the pilot lamp of

UC18YKSL charger lights for 1 second, does not

light for 0.5 seconds (oﬀ for 0.5 seconds). The

battery will not be recharged. In such a case, let

the battery cool before charging.

English

●

When the pilot lamp ﬂ ickers (at 0.2-second

intervals), check for and take out any foreign

objects in the charger’s battery connector. If

there are no foreign objects, it is probable that

the battery or charger is malfunctioning. Take it

to your authorized Service Center.

BEFORE USE

Check the work area to make sure that it is clear of debris

and clutter.

Clear the area of unnecessary personnel. Ensure that

lighting and ventilation is adequate.

OPERATION

1. Installing the bit

Always follow the following procedure to install driver

bit. (Fig. 7)

Driver bit

Hexagonal hole in the anvil

Guide sleeve

Movement

Fig. 7

(1) Pull the guide sleeve forward.

(2) Insert the bit into the hexagonal hole in the anvil.

(3) Release the guide sleeve and it returns to its origianl

position.

CAUTION

If the guide sleeve does not return to its original

position, then the bit is not installed properly.

2. Removing the bit

Please do the opposite point on the method of

installing bit.

3. Conﬁ rm that the battery is mounted correctly.

4. Check the rotational direction.

The bit rotates clockwise (viewed from the rear side)

by pushing the R-side of the pushing button.

The L-side of the pushing button is pushed to turn the

bit counterclockwise (See Fig. 8). (The

and

marks are provided on the body.)

push push

Trigger switch

Pushing button

marks marks

Fig. 8

CAUTION

The pushing button can not be switched while

the power tool is turning. To switch the pushing

button, stop the power tool, then set the pushing

button.

5 Switch operation

○

When the trigger switch is depressed, the tool rotates.

When the trigger is released, the tool stops.

○

The rotational speed can be controlled by varying

the amount that the trigger switch is pulled. Speed

is low when the trigger switch is pulled slightly and

increases as the trigger switch is pulled more.

○

When releasing the trigger of the switch, the brake will

be applied for immediate stopping.

NOTE

A buzzing noise is produced when the motor is about

to rotate; this is only a noise, not a machine failure.

6. Using the hook

The hook is used to hang up the power tool to your

waist belt while working.

CAUTION

●

When using the hook, hang up the power tool

ﬁ rmly not to drop accidentally.

If the power tool is dropped, it may lead to an

accident.

●

When electing to carry the tool hooked to your

hip belt, make sure to detach the tool bit and side

handle.

Failure to do so may result in unexpected injury.

●

Install securely the hook. Unless the hook is

securely installed, it may cause an injury while

using.

English

As the remaining battery indicator shows somewhat

diﬀ erently depending on ambient temperature and

battery characteristics, read it as a reference.

Display panel

Switch trigger

Remaining battery

indicator lamp

Fig. 11

NOTE

Do not give a strong shock to the display panel or

break it. It may lead to a trouble.

8. How to use the LED light

While the switch is pulled, the LED light will

automatically light up the tip portion of the tool.

(Fig. 12)

The LED light will automatically turn oﬀ 10 seconds

after the switch is released.

Switch trigger

Fig. 12

CAUTION

●

Do not expose directly your eye to the light by

looking into the light.

If your eye is continuously exposed to the light,

your eye will be hurt.

●

Wipe oﬀ any dirt or grime attached to the lens of

the LED light with a soft cloth, being careful not

to scratch the lens.

Scratches on the lens of the LED light can result

in decreased brightness.

(1) Removing the hook.

Remove the screws ﬁ xing the hook with Philips screw

driver. (Fig. 9)

Hook

Screw

Groove

Fig. 9

(2) Replacing the hook and tightening the screws.

Install securely the hook in the groove of power

tool and tighten the screws to ﬁ x the hook ﬁ rmly.

(Fig. 10)

Screw

Hook

Groove

Fig. 10

7. About Remaining Battery Indicator

Remaining battery power can be veriﬁ ed by pulling on

the switch to light up the remaining battery indicator

lamp. (Fig. 11)

The indicator lamp will turn oﬀ 10 seconds after the

switch is released.

The Table 5 shows the state of remaining battery

indicator lamp and the battery remaining power.

Table 5

State of lamp

Battery Remaining Power

The battery remaining power is

enough.

The battery remaining power

is a half.

The battery remaining power is

nearly empty.

Re-charge the battery soonest

possible.

English

tightening. In this case, stop impact on the nut and

hold the bolt head with a wrench before restarting

impact, or manually tighten the bolt and nut to prevent

them slipping.

11. LED light warning signals (Fig. 13)

This product features functions that are designed

to protect the tool itself as well as the battery. While

the switch is pulled, if any of the safeguard functions

activate during operation, the LED light will blink as

described in Table 6. When any of the safeguard

functions are triggered, immediately remove your

ﬁ nger from the switch and follow the instructions

described under corrective action.

Fig. 13

9. Tightening and loosening screws

Install the bit that matches the screw, line up the bit in

the grooves of the head of the screw, then tighten it.

Push the impact driver just enough to keep the bit

ﬁ tting the head of the screw.

CAUTION

●

Applying the impact driver for too long tightens

the screw too much and can break it.

●

Tightening a screw with the impact driver at an

angle to that screw can damage the head of the

screw and the proper force will not be transmitted

to the screw. Tighten with this impact driver lined

up straight with the screw.

10. Tightening and loosening bolts

A hex. socket matching the bolt or nut must ﬁ rst be

selected. Then mount the socket on the anvil, and grip

the nut to be tightened with the hex. socket. Holding

the tool in line with the bolt, press the power switch to

impact the nut for several seconds.

If the nut is only loosely ﬁ tted to the bolt, the bolt

may turn with the nut, therefore mistaking proper

Table 6

Safeguard Function LED Light Display Corrective Action

Overburden Protection

On 0.1 second/oﬀ 0.1 second

Remove the cause of the overburdening.

Temperature Protection

On 0.5 second/oﬀ 0.5 second

Allow the tool and battery to thoroughly cool.

OPERATIONAL CAUTIONS

1. Resting the unit after continuous work

After use for continuous bolt-tightening work, rest the

unit for 15 minutes or so when replacing the battery.

The temperature of the motor, switch, etc., will rise

if the work is started again immediately after battery

replacement, eventually resulting in burnout.

CAUTION

Do not touch the metal parts, as it gets very hot

during continuous work.

2. Cautions on use of the speed control switch

This switch has a built-in, electronic circuit which

steplessly varies the rotation speed. Consequently,

when the switch trigger is pulled only slightly (low

speed rotation) and the motor is stopped while

continuously driving in screws, the components of

the electronic circuit parts may overheat and be

damaged.

3. Use a tightening time suitable for the screw

The appropriate torque for a screw diﬀ ers according to

the material and size of the screw, and the material being

screwed etc., so please use a tightening time suitable for

the screw. In particular, if a long tightening time is used

in the case of screws smaller than 5/16" (M8), there is

a danger of the screw breaking, so please conﬁ rm the

tightening time and the tightening torque beforehand.

4. Work at a tightening torque suitable for the bolt under

impact

The optimum tightening torque for nuts or bolts

diﬀ ers with material and size of the nuts or bolts. An

excessively large tightening torque for a small bolt

may stretch or break the bolt. The tightening torque

increases in proportion to the operation time. Use the

correct operating time for the bolt.

5. Holding the tool

Hold the tool ﬁ rmly with both hands. In this case hold

the tool in line with the screw or bolt.

It is not necessary to push the tool very hard. Hold the tool

with a force just suﬃ cient to counteract the impact force.

English

6. Conﬁ rm the tightening torque

The following factors contribute to a reduction of the

tightening torque. So conﬁ rm the actual tightening

torque needed by screwing up some bolts before the

job with a hand torque wrench. Factors aﬀ ecting the

tightening torque are as follows.

(1) Voltage

When the discharge margin is reached, voltage

decreases and tightening torque is lowered.

(2) Operating time

The tightening torque increases when the operating

time increases. But the tightening torque does not

increase above a certain value even if the tool is

driven for a long time.

(3) Diameter of bolt

The tightening torque diﬀ ers with the diameter of the

bolt. Generally a larger diameter bolt requires larger

tightening torque.

(4) Tightening conditions

The tightening torque diﬀ ers according to the torque

ratio; class, and length of bolts even when bolts with

the same size threads are used. The tightening torque

also diﬀ ers according to the condition of the surface of

workpiece through which the bolts are to be tightened.

When the bolt and nut turn together, torque is greatly

reduced.

(5) Tightening torque varies, depending on the battery’s

charge level.

MAINTENANCE AND INSPECTION

CAUTION:

Pull out battery before doing any inspection or maintenance.

. Checking the condition of the bit

The bits should be checked regularly. If worn or

broken bits can slip or decrease the eﬃ ciency of the

motor and burn it out.

Replace worn bits with new ones.

CAUTION

If you use a driver bit of which point is worn or

broken, it will be dangerous since it slips. So

replace it with a new one.

2. Check the Screws

Loose screws are dangerous. Regularly inspect them

and make sure they are tight.

CAUTION

Using this power tool with loosened, screws is

extremely dangerous.

3. Maintenance of the motor

The motor unit winding is the very “heart” of the power

tool.

Exercise due care to ensure the winding does not

become damaged and/or wet with oil or water.

4. Check for Dust

Dust may be removed with a soft cloth or a cloth

dampened with soapy water.

Do not use bleach, chlorine, gasoline or thinner, for

they may damage the plastics.

5. Disposal of the exhausted battery

WARNING

Do not dispose of the exhausted battery. The

battery must explode if it is incinerated. The

product that you have purchased contains a

rechargeable battery. The battery is recyclable.

At the end of it’s useful life, under various state

and local laws, it may be illegal to dispose of this

battery into the municipal waste stream. Check

with your local solid waste oﬃ cials for details in

your area for recycling options or proper disposal.

6. Storage

Storing in a place below 104°F (40°C) and out of the

reach of children.

NOTE

Storing lithium-ion batteries

Make sure the lithium-ion batteries have been fully

charged before storing them.

Prolonged storage (3 months or more) of batteries with

a low charge may result in performance deterioration,

signiﬁ cantly reducing battery usage time or rendering

the batteries incapable of holding a charge.

However, signiﬁ cantly reduced battery usage time

may be recovered by repeatedly charging and using

the batteries two to ﬁ ve times.

If the battery usage time is extremely short despite

repeated charging and use, consider the batteries

dead and purchase new batteries.

7. Service and repairs

All quality power tools will eventually require servicing or

replacement of parts because of wear from normal use.

To assure that only authorized replacement parts will be

used, all service and repairs must be performed by a

HITACHI AUTHORIZED SERVICE CENTER, ONLY.

English

8. Service parts list

CAUTION

Repair, modiﬁ cation and inspection of Hitachi

Power Tools must be carried out by a Hitachi

Authorized Service Center.

This Parts List will be helpful if presented with

the tool to the Hitachi Authorized Service Center

when requesting repair or other maintenance. In

the operation and maintenance of power tools,

the safety regulations and standards prescribed

in each country must be observed.

MODIFICATIONS:

Hitachi Power Tools are constantly being improved

and modiﬁ ed to incorporate the latest technological

advancements.

Accordingly, some parts may be changed without

prior notice.

Important notice on the batteries for the Hitachi

cordless power tools

Please always use one of our designated genuine

batteries. We cannot guarantee the safety and

performance of our cordless power tool when used

with batteries other than these designated by us, or

when the battery is disassembled and modiﬁ ed (such

as disassembly and replacement of cells or other

internal parts).

TROUBLESHOOTING GUIDE

WARNING

●

To avoid injury from an accidental start, turn the switch OFF and remove the plug from the power source

or remove the battery from the main body before making any adjustments.

●

All electrical or mechanical repairs should be done only by qualiﬁ ed service technicians. Contact Hitachi

Authorized Service Center.

Problem Possible Cause Possible Solution

Tool doesn’t run No remaining battery power Charge the battery.

The trigger switch was held down while

the battery was inserted.

The safety function was activated.

If the trigger switch is released once and

then pulled again, the tool will run.

Tool suddenly stopped Tool was overburdened Get rid of the problem causing the

overburden.

The battery is overheated. Let the battery cool down.

The trigger switch was held down for 5

minutes or more.

This is not a malfunction.

The motor was automatically stopped to

prevent failure of the tool.

Tool bits

-can’t be attached

-fall oﬀ

The shape of the attachment portion

doesn’t match

Use a bit with a hexagonal shaft that has a

width across ﬂ ats of 6.35 mm.

If you are using an L-type tool bit, replace it

with an S-type bit.

Switch can’t be pulled Forward/reverse selector button is

positioned halfway

Press the button ﬁ rmly into position for the

desired direction of rotation.

An abnormal high-pitched

noise occurs when the

trigger switch is pulled.

The trigger switch is being pulled only

slightly.

This is not a malfunction.

It does not occur if the trigger switch is

pulled more fully.

Screw head slips or comes

loose.

Bit number doesn’t match with the screw

size

Install a suitable bit.

The bit is worn Replace with a new bit.

English

ACCESSORIES

WARNING

ALWAYS use Only authorized HITACHI replacement parts and accessories. Never use replacement parts

or accessories which are not intended for use with this tool. Contact HITACHI if you are not sure whether

it is safe to use a particular replacement part or accessory with your tool.

The use of any other attachment or accessory can be dangerous and could cause injury or mechanical

damage.

NOTE

Accessories are subject to change without any obligation on the part of the HITACHI.

STANDARD ACCESSORIES

WH18DBFL2

(2LEGK)

Battery (BSL1815) ................................................................................. 2

Battery Charger (UC18YKSL) ............................................................... 1

Plastic Case (Code No. 336642) ........................................................... 1

Battery cover (Code No. 329897) ......................................................... 1

WH18DBFL2

(LMGX)

Battery (BSL1830C) .............................................................................. 1

Battery Charger (UC18YKSL) ............................................................... 1

Bag (Code No. 331417) ......................................................................... 1

Battery cover (Code No. 329897) ......................................................... 1

English

OPTIONAL ACCESSORIES.....sold separately

1. Battery (BSL1815 / BSL1830C)

2. Phillips bit

2"(50mm)

Bit No. Code No.

No.2 992671

No.3 992672

. Hexagonal socket

Part Name

Engraved

characters

LBCode No.

5 mm Hexagonal socket 8 65 8 996177

6 mm Hexagonal socket 10 65 10 985329

5/16" Hexagonal socket 12 65 12 996178

8 mm Hexagonal socket 13 65 13 996179

10 mm Hexagonal socket (small type) 14 65 14 996180

10 mm Hexagonal socket 16 65 16 996181

10 mm Hexagonal socket 17 65 17 996182

1/2" Hexagonal long socket 21 166 21 996197

Engraved characters

4. Drill chuck adapter set: Code No. 321823

Use the drill available on the market.

NOTE

Speciﬁ cations are subject to change without any

obligation on the part of the HITACHI.

English

INFORMATIONS IMPORTANTES DE SÉCURITÉ

Lire et comprendre toutes les précautions de sécurité, les avertissements et les instructions de fonctionnement dans ce

mode d’emploi avant d’utiliser ou d’entretenir cet outil motorisé.

La plupart des accidents causés lors de l’utilisation ou de l’entretien de l’outil motorisé proviennent d’un non respect des

règles ou précautions de base de sécurité. Un accident peut la plupart du temps être évité si l’on reconnaît une situation

de danger potentiel avant qu’elle ne se produise, et en observant les procédures de sécurité appropriées.

Les précautions de base de sécurité sont mises en évidence dans la section “SECURITE” de ce mode d’emploi et dans

les sections qui contiennent les instructions de fonctionnement et d’entretien.

Les dangers qui doivent être évités pour prévenir des blessures corporelles ou un endommagement de la machine sont

identiﬁ és par AVERTISSEMENTS sur l’outil motorisé et dans ce mode d’emploi.

NE JAMAIS utiliser cet outil motorisé d’une manière qui n’est pas spéciﬁ quement recommandée par HITACHI.

SIGNIFICATION DES MOTS D’AVERTISSEMENT

AVERTISSEMENT indique des situations potentiellement dangereuses qui, si elles sont ignorées, pourraient entraîner

la mort ou de sérieuses blessures.

PRECAUTION indique des situations dangereuses potentilles qui, si elles ne sont pas évitées, peuvent entraîner de

mineures et légères blessures ou endommager la machine.

REMARQUE met en relief des informations essentielles.

SECURITE

AVERTISSEMENTS DE SÉCURITÉ GÉNÉRAUX CONCERNANT LES OUTILS ÉLECTRIQUES

AVERTISSEMENT

Lire tous les avertissements de sécurité et toutes les instructions

Tout manquement à observer ces avertissements et instructions peut engendrer des chocs électriques, des

incendies et/ou des blessures graves.

Conservez tous les avertissements et toutes les instructions pour vous y référer ultérieurement.

Le terme "outil électrique", utilisé dans les avertissements, se réfère aux outils électriques (câblé) ou aux outils à

piles (sans ﬁ l).

1) Sécurité de l’aire de travail

a) Maintenir l'aire de travail propre et bien

éclairée.

Les endroits encombrés ou sombres sont

propices aux accidents.

b) Ne pas utiliser d'outils électriques en

présence de liquides, gaz ou poussière

inﬂ ammables, au risque de provoquer une

explosion.

Les outils électriques créent des étincelles

susceptibles d'enﬂ ammer la poussière.

c) Ne pas laisser les enfants et les visiteurs

s'approcher de vous lorsque vous utiliser un

outil électrique.

Les distractions peuvent faire perdre le contrôle.

2) Sécurité électrique

a) Les prises de l'outil électrique doivent

correspondre à la prise secteur.

Ne jamais modiﬁ er la prise.

Ne pas utiliser d'adaptateurs avec les outils

électriques mis à la masse.

Les prises non modiﬁ ées et les prises secteurs

correspondantes réduisent les risques de choc

électrique.

b) Eviter tout contact avec les surfaces mises

à la masse telles que les tuyaux, radiateurs,

bandes et réfrigérateurs.

Le risque de choc électrique est accru en cas de

mise à la masse du corps.

c) Ne pas exposer les outils électriques à la

pluie ou à des conditions humides.

Si l'eau pénètre dans l'outil, cela augmente les

risques de choc électrique.

d) Ne pas utiliser le cordon à tort. Ne jamais

utiliser le cordon pour transporter ou

débrancher l'outil électrique.

Français

La page est en cours de chargement...

Hitachi WH 18DBFL2 Manuel utilisateur

Marque: Hitachi

Modèle: WH 18DBFL2

Catégorie: Perceuses mixtes sans fil

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Hitachi WH 18DBFL2 User manual
español: Hitachi WH 18DBFL2 Manual de usuario

Hitachi WH 18DBFL2 Manuel utilisateur

Hitachi WH 18DBFL2 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents