Samsung LN-S3238D Le manuel du propriétaire

Owner’s

Instructions

Register your product at

www.samsung.com/global/register

LN-S2738D

LN-S3238D

LN-S3738D

TFT-LCD TELEVISION

BN68-00883V-00

Contact SAMSUNG WORLD-WIDE

If you have any questions or comments relating to Samsung products, please contact the SAMSUNG

customer care center.

Comment contacter Samsung dans le monde

Si vous avez des suggestions ou des questions concernant les produits Samsung, veuillez contacter le Service

Consommateurs Samsung.

Contacte con SAMSUNG WORLD-WIDE

Si tiene alguna pregunta o comentario referente a nuestros productos, por favor contacte con nuestro Servicio de

Atención al Cliente.

Country

CANADA

U.S.A

Customer Care Center

1-800-SAMSUNG (7267864)

Address

Samsung Electronics Canada Inc., Customer Service

55 Standish Court Mississauga, Ontario L5R 4B2

Canada

Samsung Electronique Canada Inc., Service

á

la Client

é

le

55 Standish Court Mississauga, Ontario L5R 4B2

Canada

Samsung Electronics America, Inc.

105 Challenger Road

Ridgefield Park, NJ 07660-0511

Web Site

www.samsung.com/ca

www.samsung.com

BN68-00883V-00Cover.qxd 10/2/04 3:11 AM Page 1

Precautions When Displaying a Still Image

A still image may cause permanent damage to the TV screen.

• Do not display a still image on the LCD panel for more than 2 hours as it can cause screen image retention.

This image retention is also known as "screen burn".

To avoid such image retention, reduce the degree of brightness and contrast of the screen when displaying a still image.

• Watching the LCD TV in 4:3 format for a long period of time may leave traces of borders displayed on the left, right and center of the screen

caused by the difference of light emission on the screen.

Playing a DVD or a game console may cause a similar effect to the screen.

Damages caused by the above effect are not covered by the Warranty.

• Displaying still images from Video games and PC for longer than a certain period of time may produce partial after-images.

To prevent this effect, reduce the ‘brightness’ and ‘contrast’ when displaying still images.

Précautions à prendre lors de l'affichage d'une image fixe

Une image fixe peut causer des dommages irrémédiables à l'écran du téléviseur.

• N'affichez pas une image fixe sur l'écran LCD plus de 2 heures. Cela pourrait provoquer une rémanence de l'image à l'écran.

Cette rémanence de l'image est également appelée "brûlure de l'écran".

Pour éviter une telle rémanence de l'image à l'écran, réduisez la luminosité et le contraste de l'écran lorsque vous laissez une image fixe affichée.

• Regarder l'écran LCD du téléviseur en format 4:3 pendant une longue période peut laisser des traces de bordures à gauche,

à droite et au centre de l'écran, à cause de la différence d'émission de lumière sur l'écran.

La lecture d'un DVD ou l'utilisation d'une console de jeu peut avoir un effet similaire sur l'écran.

Les dommages provoqués par les effets qui précèdent ne sont pas couverts par la garantie.

• L'affichage d'images fixes de jeux vidéo et d'ordinateurs pendant plus longtemps qu'une période spécifique peut provoquer des rémanences.

Pour éviter cela, réduisez la "luminosité" et le "contraste" lors de l'affichage d'images fixes.

Precauciones al mostrar en la pantalla una imagen fija

La imagen fija puede causar daños permanentes en la pantalla del televisor.

• No deje una imagen fija en la pantalla LCD durante más de dos horas ya que se podría producir una retención de la imagen en la pantalla. Este fenómeno de

retención de imágenes también se denomina "quemadura de pantalla".

Para evitar que se produzca esa persistencia de la imagen, reduzca el nivel de luminosidad y de contraste de la pantalla cuando muestre imágenes fijas.

• El uso del televisor LCD en formato 4:3 durante un tiempo prolongado puede dejar rastros de bordes en las partes izquierda,

derecha y central de la pantalla debido a las diferencias en la emisión lumínica de la pantalla.

La reproducción de un DVD o el uso de una consola de videojuegos pueden provocar un efecto similar en la pantalla.

Reproducir un DVD o una videoconsola puede causar un efecto similar en la pantalla. La garantía no cubre estos daños.

• Ver imágenes fijas de videojuegos y PC durante más tiempo del indicado puede producir restos de imágenes parciales.

Para evitar este efecto, reduzca el 'brillo' y el 'contraste' cuando vea imágenes fijas.

BUKMI-Still(Eng).qxd 10/2/04 3:11 AM Page 1

English

Symbol Press Important Note One-Touch

Button

Contents

GENERAL INFORMATION

List of Features .................................................................................. 2

Accessories........................................................................................ 2

Viewing the Control Panel.................................................................. 3

Viewing the Connection Panel........................................................... 4

Remote Control.................................................................................. 6

Installing Batteries in the Remote Control ......................................... 7

CONNECTIONS

Connecting VHF and UHF Antennas ................................................. 7

Connecting Cable TV......................................................................... 8

Connecting a VCR ............................................................................. 9

Connecting an S-VHS VCR ............................................................... 9

Connecting a Camcorder

(LN-S3238D, LN-S3738D)

............................ 10

Connecting a DVD Player/Set-Top Box ............................................. 10

Connecting a DVD Player/Set-Top Box via DVI ................................ 10

Connecting a DVD Player/Set-Top Box via HDMI ............................. 11

Connecting a Digital Audio System.................................................... 11

Connecting an Amplifier/DVD Home Theater .................................... 12

Connecting a PC................................................................................ 12

OPERATION

Turning the TV On and Off ............................................................... 13

Plug & Play Feature........................................................................... 13

Changing Channels ........................................................................... 14

Adjusting the Volume ......................................................................... 15

Viewing the Display............................................................................ 15

Viewing the Menus............................................................................. 15

Memorizing the Channels .................................................................. 16

Setting Up Your Remote Control........................................................ 17

To Select the Source (depending on the model) ............................... 22

To Edit the Input Source Name (depending on the model) ............... 22

PICTURE CONTROL

Using Automatic Picture Settings ................................................. 23

Adjusting the Color Tone .............................................................. 24

DNIe Demo(Digital Natural Image engine)................................... 24

Changing the Screen Size............................................................ 25

Freezing the Picture ..................................................................... 26

Viewing Picture-in-Picture............................................................. 26

SOUND CONTROL

Customizing the Sound ................................................................ 28

Using Automatic Sound Settings ................................................. 28

Setting the TruSurround XT.......................................................... 28

Choosing a Multi-Channel Sound (MTS) track - Digital .............. 29

Choosing a Multi-Channel Sound (MTS) track - Analog ............. 29

Selecting the Internal Mute........................................................... 30

Automatic Volume Control ........................................................... 30

Setting the On/Off Melody ............................................................ 31

Listening to the Sound of the Sub (PIP) Picture .......................... 31

CHANNEL CONTROL

Selecting the Antenna................................................................... 32

Setting the Channel Manager....................................................... 32

To set-up Your Favorite Channels ............................................... 33

Using the Channel Lists................................................................ 34

Viewing the Channel Lists ............................................................ 34

Labeling Channels ....................................................................... 35

Fine Tuning Analog Channels....................................................... 35

Checking the Digital-Signal Strength............................................ 36

LNA (Low Noise Amplifier)............................................................ 36

PC DISPLAY

Using Your TV as a Computer (PC) Display ................................ 37

Display Modes .............................................................................. 37

Setting up the TV with your PC .................................................... 38

TIME SETTING

Setting the Clock .......................................................................... 40

FUNCTION DESCRIPTION

Selecting a Menu Language......................................................... 43

Setting the Blue Screen Mode...................................................... 43

Selecting the Film Mode............................................................... 44

Digital Noise Reduction ................................................................ 44

Using the Game Mode.................................................................. 44

Viewing Closed Captions (On-Screen Text Messages) - Analog

... 45

Viewing Closed Captions (On-Screen Text Messages) - Digital .. 46

Menu Transparency Level ............................................................ 47

Using the Energy Saving Feature ................................................ 47

Setting the Function Help ............................................................ 48

Using the V-Chip........................................................................... 48

APPENDIX

Identifying Problems .................................................................... 55

Installing the Stand ....................................................................... 56

Disconnecting the Stand............................................................... 56

Installing the Wall Mount Kit (LN-S2738D)................................... 57

Installing the Wall Mount Kit (LN-S3238D, LN-S3738D).............. 58

Using the Anti-Theft Kensington Lock .......................................... 59

Specifications................................................................................ 59

English-1

BN68-00883V-00Eng.qxd 10/1/04 10:57 PM Page 1

English-2

List of Features

 Adjustable picture settings that can be stored in the TV’s memory.

 Automatic timer to turn the TV on and off.

 A special sleep timer.

 V

-

Chip function.

 Excellent Digital Interface & Networking

With a built-in HD digital tuner, non-subscription HD broadcasts can be viewed with no Set-Top Box needed.

 Remote Control

The supplied remote can be used to operate the TV as well as most DVD players, Set-top boxes, Cable Boxes and VCRs.

 Excellent Picture Quality

-

DNIe technology provides life-like clear images.

 SRS TruSurround XT

-

SRS TruSurround XT provides a virtual Dolby surround system.

Accessories

Please make sure the following items are included with your LCD TV.

If any items are missing, contact your dealer.

M4 X L16

General Information

Remote Control & Batteries (AAA x 2)

(BN59-00511A)

Power Cord

(3903-000144)

Cleaning Cloth

(BN63-01798A)

Cover-Bottom

LN-S2738D (BN63-01674A)

LN-S3238D (BN63-01674A)

LN-S3738D (BN63-01955A)

Stand

LN-S2738D (BN96-01727B)

LN-S3238D (BN96-01733B)

LN-S3738D (BN96-02402B)

Stand Screw Owner’s Instructions Warranty Card / Registration Card

/Safety Guide Manual

(Not available in all locations)

BN68-00883V-00Eng.qxd 10/1/04 10:57 PM Page 2

English-3

Viewing the Control Panel

SOURCE

Toggles between all the available input sources

(TV, AV1, AV2, S-Video1, S-Video2, Component, PC,

HDMI1, HDMI2).

In the on-screen menu, use this button as you would

use the ENTER button on the remote control.

27 inch model supports TV, AV, S-Video,

Component, PC, HDMI1, and HDMI2 only.

MENU

Press to see an on-screen menu of your TV’s features.

Press to decrease or increase the volume.

In the on-screen menu, use the buttons as you

would use the

 and  buttons on the remote control.

Press to change channels.

In the on-screen menu, use the buttons as you

would use the  and  buttons on the remote control.

(POWER)

Press to turn the TV on and off.

Power Indicator

Blinks and turns off when the power is on and lights up

in stand-by mode.

Remote Control Sensor

Aim the remote control towards this spot on the TV.

Speakers

Buttons on the Lower-Right Part of the Panel

The buttons on the lower-right panel control your TV’s basic features, including the on-screen menu.

To use the more advanced features, you must use the remote control.

The product color and shape may vary depending on the model.

BN68-00883V-00Eng.qxd 10/1/04 10:57 PM Page 3

English-4

AV IN1

Video and audio inputs for external devices, such as a

camcorder or VCR.

S-VIDEO 1

Connect an S-Video signal from a camcorder or VCR.

AUDIO OUT

Connect to the audio input jacks on your Amplifier/

Home theater.

DIGITAL AUDIO OUT (OPTICAL)

Connect to a Digital Audio component.

SERVICE 1/SERVICE 2

Connector for service only.

HDMI/DVI IN 1,2 / DVI IN (R-AUDIO-L)

Connect to the HDMI jack of a device with an HDMI output.

Use the HDMI/DVI terminal for DVI connection to an external

device. You should use the DVI to HDMI cable or DVI-HDMI

adapter (DVI to HDMI) for video connection, and the

DVI-IN ‘R-AUDIO-L’ terminal for audio.

- HDMI/DVI IN terminal does not support PC.

- No sound connection is needed for an HDMI to HDMI

connection.

HEADPHONE

(LN-S2738D)

Connect a set of external headphones for private listening.

ANT 1 IN/ANT 2 IN

Connect to an antenna or cable TV system.

PC IN

Connect to the video and audio output jacks on your PC.

COMPONENT IN

Connect Component video/audio.

POWER INPUT

Connect the supplied power cord.

The place of the power input may be different depending

on its model.

KENSINGTON LOCK

The Kensington lock (optional) is a device used to

physically fix the system when used in a public place.

If you want to use a locking device, contact the dealer

where you purchased the TV.

The place of the Kensington Lock may be different depending

on its model.

Rear Panel Jacks

Use the rear panel jacks to connect A/V components that will be connected continuously, such as VCR or DVD players.

For more information on connecting equipment, see pages 7-12.

Viewing the Connection Panel

LN-S2738D

LN-S3238D

LN-S3738D

The product color and shape may vary depending on the model.

BN68-00883V-00Eng.qxd 10/1/04 10:57 PM Page 4

English-5

AV IN2

Video and audio inputs for external devices.

S-VIDEO 2

Video inputs for external devices with an S-Video output.

HEADPHONE

Connect a set of external headphones for private listening.

Side Panel Jacks (LN-S3238D, LN-S3738D)

Use the left side panel jacks to connect a component that is used only occasionally, such as a camcorder or video game. (See page 10)

BN68-00883V-00Eng.qxd 10/1/04 10:57 PM Page 5

English-6

Remote Control

You can use the remote control up to a distance of about 23 feet from the TV. When using the remote, always point it directly at the TV.

You can also use your remote control to operate your VCR, Cable box, DVD player, or Set-Top Box.

POWER

Turns the TV on and off.

NUMERIC BUTTONS

Press to change the channel.

–

Press to select additional channels

(digital and analog) being broadcast by

the same station. For example, to

select channel “54-3”, press “54”, then

press “

–

” and “3”.

CH MGR

Used to display Channel Lists on the

screen.

ANTENNA

Press to select “AIR” or “CABLE”.

VCR/DVD Functions

- Rewind

- Stop

- Play/Pause

- Fast/Forward

VOL / VOL

Press to increase or decrease the

volume.

(

MUTE)

Press to temporarily cut off the sound.

MENU

Displays the main on-screen menu.

S.MODE

Sound mode selection.

PIP

Picture-in Picture ON/OFF.

P. MODE

Picture effect selection.

SRS

Selects SRS TruSurround XT mode.

MTS

Press to choose stereo, mono or

Separate Audio Program

(SAP broadcast).

AUTO PROG.

Press to automatically store selected

TV/Cable channels.

ADD/DEL

Use to store and delete channels

to/from memory.

SET

Sets the remote to control your

TV, VCR, Cable, DVD, or Set-Top Box

TV, DVD, STB, CABLE, VCR

Press to operate your TV,

DVD, STB, CABLE (box), or VCR

SOURCE

Press to display all of the available

video sources.

PRE-CH

Tunes to the previous channel.

FAV.CH

Press to switch to your favorite channels.

E.SAVING

Adjusts screen brightness to save energy.

CH / CH

Press to change channels.

EXIT

Press to exit the menu.

UP / DOWN / LEFT /

RIGHT / ENTER

Use to select on-screen menu items

and change menu values.

INFO

Press to display information on the TV

screen.

SLEEP

Press to select a preset time interval for

automatic shut off.

STILL

Press to stop the action during a

particular scene.

Press again to resume normal video.

P. SI ZE

Picture size selection.

PIP FUNCTIONS

SWAP

:

Switches the main and sub

(PIP) picture.

CH: Displays the available channels in

sequence. (These buttons change

channels in the PIP window only.)

CAPTION

Controls the caption decoder.

RESET

When your remote does not work,

change the batteries and press the

RESET button for 2-3 seconds

before use.

This is a special remote control for the visually impaired, and has Braille points on the Power,

Channel, Volume, Stop and Play/Pause buttons.

The performance of the remote control may be affected by bright light.

BN68-00883V-00Eng.qxd 10/1/04 10:57 PM Page 6

English-7

1. Place the wires from the twin leads under the screws on a 300-75

Ω

adapter

(not supplied).

Use a screwdriver to tighten the screws.

2. Plug the adaptor into the ANT 2 IN (CABLE) terminal on the back of the TV.

Connecting VHF and UHF Antennas

If your antenna has a set of leads that look like this, see “Antennas with 300

Ω

Flat Twin Leads”

below.

If your antenna has one lead that looks like this, see “Antennas with 75

Ω

Round Leads”.

If you have two antennas, see “Separate VHF and UHF Antennas”.

Antennas with 300 Ω Flat T

win Leads

If you are using an off-air antenna (such as a roof antenna or “rabbit ears”) that has 300

Ω

twin flat leads, follow the directions below.

1. Plug the antenna lead into the ANT 1 IN (AIR) terminal on the back of the TV.

Antennas with 75 Ω Round Leads

1. Connect both antenna leads to the combiner.

2. Plug the combiner into the ANT 1 IN (AIR) terminal on the bottom of the rear panel.

Separate VHF and UHF Antennas

If you have two separate antennas for your TV (one VHF and one UHF), you must combine the two antenna signals before connecting

the antennas to the TV. This procedure requires an optional combiner-adaptor (available at most electronics shops).

UHF

VHF

ANT 1 IN

(AIR)

ANT 2 IN

(CABLE)

ANT 1 IN

(AIR)

1. Lift the cover at the back of the remote control upward as shown in the figure.

2. Install two AAA size batteries.

Make sure to match the “+” and “–” ends of the batteries with the diagram inside the compartment.

3. Replace the cover.

Remove the batteries and store them in a cool, dry place if you won’t be using the remote control for a long time.

The remote control can be used up to about 23 feet from the TV.

(Assuming typical TV usage, the batteries last for about one year.)

If the remote control doesn’t work, check the following:

1. Is the TV power on?

2. Are the plus and minus ends of the batteries reversed?

3. Are the batteries drained?

4. Is there a power outage, or is the power cord unplugged?

5. Is there a special fluorescent light or neon sign nearby?

Installing Batteries in the Remote Control

UHF

VHF

Connections

BN68-00883V-00Eng.qxd 10/1/04 10:57 PM Page 7

English-8

After you have made this connection, set the A/B switch to the “A” position for normal viewing. Set the A/B switch to the “B” position to view scrambled

channels. (When you set the A/B switch to “B”, you will need to tune your TV to the cable box’s output channel, which is usually channel 3 or 4.)

2. Connect this cable to a two-way splitter.

Splitter

Incoming

cable

3. Connect an RF cable between an OUTPUT

terminal on the splitter and the IN terminal

on the cable box.

Splitter

Cable Box

Incoming

cable

4. Connect an RF cable between the

ANT OUT terminal on the cable box and

the B–IN terminal on the RF(A/B) switch.

Splitter

Cable Box

RF (A/B)

Switch

Incoming

cable

5. Connect another cable between the other

OUT terminal on the splitter and the A–IN

terminal on the RF (A/B) switch.

Splitter

Cable Box

Incoming

cable

6. Connect the last RF cable between the

OUT terminal on the RF (A/B) switch and

the ANT 2 IN (CABLE) terminal on the rear

of the TV.

Splitter

Cable Box

Incoming

cable

Connecting to a Cable Box that Descrambles Some Channels

If your cable box descrambles only some channels (such as premium channels), follow the instructions below. You will need a two-way

splitter, an RF (A/B) switch, and four lengths of RF cable. (These items are available at most electronics stores.)

1. Find and disconnect the cable that is

connected to the ANT IN terminal on your

cable box.

This terminal might be labeled “ANT IN”,

“VHF IN” or simply, “IN”.

ANT IN

RF (A/B)

Switch

TV Rear

RF (A/B)

Switch

ANT 2 IN

(CABLE)

Connecting Cable TV

To connect to a cable TV system, follow the instructions below.

Cable without a Cable Box

1. Plug the incoming cable into the ANT 2 IN (CABLE) terminal on the back of the TV.

Because this TV is cable-ready, you do not need a cable box to view unscrambled cable channels.

2. Connect the other end of this cable to the ANT 2 IN (CABLE) terminal on the back of the TV.

Connecting to a Cable Box that Descrambles All Channels

1. Find the cable that is connected to the ANT OUT terminal on your cable box.

This terminal might be labeled “ANT OUT”, “VHF OUT” or simply, “OUT”.

ANT OUT

ANT IN

ANT 2 IN

(CABLE)

ANT 2 IN

(CABLE)

BN68-00883V-00Eng.qxd 10/1/04 10:57 PM Page 8

English-9

Connecting a VCR

These instructions assume that you have already connected your TV to an antenna or a cable TV system (according to the instructions on

pages 7-8). Skip step 1 if you have not yet connected to an antenna or a cable system.

1. Unplug the cable or antenna

from the back of the TV.

2. Connect the cable or antenna

to the ANT IN terminal on the

back of the VCR.

3. Connect an RF Cable

between the ANT OUT

terminal on the VCR and the

ANT 1 IN (AIR) or ANT 2 IN

(CABLE) terminal on the TV.

4. Connect a Video Cable

between the VIDEO OUT jack

on the VCR and the AV IN 1

[VIDEO] jack on the TV.

5. Connect Audio Cables

between the AUDIO OUT

jacks on the VCR and the

AV IN 1 [R-AUDIO-L] jacks

on the TV.

If you have a “mono”

(non-stereo) VCR, use a

Y-connector (not supplied) to

hook up to the right and left

audio input jacks of the TV.

If your VCR is stereo, you

must connect two cables.

ANT 2 IN

(CABLE)

Follow the instructions in “Viewing a VCR or Camcorder Tape” to view your VCR tape.

Each VCR has a different back panel configuration.

When connecting a VCR, match the color of the connection terminal to the cable.

VCR Rear Panel

TV Rear Panel

RF Cable (Not supplied)

Video Cable (Not supplied)

Audio Cable (Not supplied)

2

3

4

5

Connecting an S-VHS VCR

Your Samsung TV can be connected to an S-Video signal from an S-VHS VCR.

(This connection delivers a better picture as compared to a standard VHS VCR.)

1. To begin, follow steps 1–3

in the previous section to

connect the antenna or

cable to your VCR and

your TV.

2. Connect an S-Video Cable

between the S-VIDEO OUT

jack on the VCR and the

AV IN1 [S-VIDEO] jack on

the TV.

3. Connect Audio Cables

between the AUDIO OUT

jacks on the VCR and the

AV IN1 [R-AUDIO-L] jacks

on the TV.

An S-Video cable is usually included with an S-VHS VCR. (If not, check your local electronics store.)

Each S-VHS VCR has a different back panel configuration.

When connecting an S-VHS VCR, match the color of the connection terminal to the cable.

VCR Rear Panel

TV Rear Panel

RF Cable (Not supplied)

S-Video Cable (Not supplied)

Audio Cable (Not supplied)

3

2

1

ANT 1 IN

(AIR)

BN68-00883V-00Eng.qxd 10/1/04 10:57 PM Page 9

English-10

Connecting a DVD Player/Set-Top Box via DVI

This connection can only be made if there is a DVI Output connector on the external device.

1. Connect a DVI to HDMI

Cable or DVI-HDMI Adapter

between the HDMI/DVI IN 1

or HDMI/DVI IN 2 connector

on the TV and the DVI

connector on the

DVD player/Set-Top Box.

2. Connect Audio Cables

between the DVI IN

[R-AUDIO-L] jack on the

TV and the AUDIO OUT

jacks on the DVD player/

Set-Top Box.

DVD Player / Set-Top Box

TV Rear Panel

Audio Cable (Not supplied)

2

Each DVD player/Set-top box has a different back panel configuration.

When connecting a DVD player/Set-top box, match the color of the connection terminal to the cable.

DVI to HDMI Cable (Not supplied)

1

Connecting a Camcorder (LN-S3238D, LN-S3738D)

The side panel jacks on your TV make it easy to connect a camcorder to your TV.

They allow you to view the camcorder tapes without using a VCR

1. Connect a Video Cable

(or S-Video Cable )between

the AV IN2 [VIDEO]

(or S-VIDEO) jack on the

TV and the VIDEO OUT

jack on the camcorder.

Camcorder

TV Side Panel

2. Connect Audio Cables

between the AV IN2

[R-AUDIO-L] jacks on the

TV and the AUDIO OUT

jacks on the camcorder.

Audio Cable (Not supplied)

Video Cable (Not supplied)

or

S-Video Cable (Not supplied)

Connecting a DVD Player/Set-Top Box

The rear panel jacks on your TV make it easy to connect a DVD player to your TV.

1. Connect a Component Cable

between the COMPONENT

IN [Y, PB, PR] jacks on the TV

and the COMPONENT OUT

[Y, PB, PR] jacks on the DVD

player/Set-Top Box.

2. Connect Audio Cables

between the COMPONENT

IN [R-AUDIO-L] jacks on

the TV and the AUDIO OUT

jacks on the DVD player/

Set-Top Box.

DVD Player / Set-Top Box

TV Rear Panel

Component Cable (Not supplied)

Audio Cable (Not supplied)

Component video separates the video into Y (Luminance (brightness)), Pb (Blue) and Pr (Red)

for enhanced video quality.

Be sure to match the component video and audio connections.

For example, if connecting the video cable to COMPONENT IN,

connect the audio cable to COMPONENT IN also.

Each DVD player/Set-top box has a different back panel configuration.

When connecting a DVD player/Set-top box, match the color of the connection terminal to the cable.

1

2

1

2

1

Each Camcorder has a different back panel configuration.

When connecting a Camcorder, match the color of the connection terminal to the cable.

BN68-00883V-00Eng.qxd 10/1/04 10:57 PM Page 10

English-11

Connecting a DVD Player/Set-Top Box via HDMI

This connection can only be made if there is an HDMI Output connector on the external device.

1. Connect an HDMI Cable

between the HDMI/DVI 1

or HDMI/DVI 2 connec-

tor on the TV and the

HDMI connector on the

DVD player/Set-Top Box.

DVD Player / Set-Top Box

TV Rear Panel

HDMI Cable (Not supplied)

What is HDMI?

• HDMI, or high-definition multimedia interface, is a next-generation interface that enables the

transmission of digital audio and video signals using a single cable without compression.

• “Multimedia interface” is a more accurate name for it especially because it allows multiple channels of

digital audio (5.1 channels).

The difference between HDMI and DVI is that the HDMI device is smaller in size, has the HDCP

(High Bandwidth Digital Copy Protection) coding feature installed, and supports multi-channel

digital audio.

Each DVD player/Set-top box has a different back panel configuration.

When connecting a DVD player/Set-top box, match the color of the connection terminal to the cable.

Connecting a Digital Audio System

The rear panel jacks on your TV make it easy to connect a Digital Audio System to your TV.

1. Connect an Optical

Cable between the DIGI-

TAL AUDIO OUT

(OPTICAL) jacks on the

TV and the Digital Audio

Input jacks on the Digital

Audio System.

When a Digital Audio

System is connected to

the “DIGITAL AUDIO

OUT (OPTICAL)” termi-

nal: Decrease the gain

(volume) of the TV, and

adjust the volume level

with the system’s vol-

ume control.

Digital Audio System

TV Rear Panel

Optical Cable (Not supplied)

What is OPTICAL?

• Converts the electric signal into an optical light signal, and transmits it through glass fibers. S/PDIF

is a transmission system of digital audio in the form of a light wave that uses a glass conductor.

5.1CH audio is possible when the TV is connected to an external device supporting 5.1CH.

Each Digital Audio System has a different back panel configuration.

BN68-00883V-00Eng.qxd 10/1/04 10:57 PM Page 11

English-12

Connecting a PC

1. Connect a D-Sub Cable

between PC IN [PC]

connector on the TV and

the PC output connector

on your computer.

2. Connect a PC Audio

Cable between PC IN

[AUDIO] jack on the TV

and the Audio Out jack

of the sound card on

your computer.

PC

TV Rear Panel

D-Sub Cable (Not supplied)

PC Audio Cable (Not supplied)

Each PC has a different back panel configuration.

When connecting a PC, match the color of the connection terminal to the cable.

The HDMI/DVI jacks do not support PC connection.

Connecting an Amplifier/DVD Home Theater

1. Connect Audio Cables

between the AUDIO

OUT [R-AUDIO-L] on the

TV and AUDIO IN

[R-AUDIO-L] on the

Amplifier/DVD Home

Theater.

When an audio amplifier

is connected to the

“AUDIO OUT

[L-AUDIO-R]” terminals:

Decrease the gain

(volume) of the TV, and

adjust the volume level

with the Amplifier’s

volume control.

Amplifier/DVD Home Theater

TV Rear Panel

Audio Cable (Not supplied)

1

2

Each Amplifier/DVD Home Theater has a different back panel configuration.

When connecting an Amplifier/DVD Home Theater, match the color of the connection terminal to the

cable.

Internal Mute Off

Internal Mute On

Video No Signal

RF

Speaker Output

Mute

Internal Speakers

AV, S-Video

Speaker Output

Mute

Component, PC, HDMI

Speaker Output

Mute

RF

Sound Output

Mute

AV, S-Video

Sound Output

Mute

Component, PC, HDMI

Sound Output

Mute

When “Internal mute” is set to “On”, Sound menu except “Multi-Track Options” cannot be adjusted.

See Selecting the Internal Mute on page 30.

Audio Out (Optical, L/R Out)

BN68-00883V-00Eng.qxd 10/1/04 10:57 PM Page 12

English-13

Turning the TV On and Off

Press the POWER button on the remote control.

You can also use the button on the front of the panel.

Plug & Play Feature

When the TV is initially powered on, two basic customer settings proceed automatically and subsequently:

1. Press the POWER button on the remote control.

The message “Menu language, Channels and Time will be set.” is displayed.

Press the ENTER button, then “Select the language of the OSD” menu is

automatically displayed.

2. Press the ENTER button to enter the language.

Press the

 or  buttons to select language, then the ENTER button.

“Select the antennas to memorize.” menu is automatically displayed.

3. Press the  or  buttons to memorize the channels of the selected connection.

Press the ENTER button to select “Start”.

If the antenna is connected to ANT 1 (AIR), select “Air” and if it is connected to

ANT 2 (CABLE), select “Cable”.

If both ANT 1 (AIR) and ANT 2 (CABLE) are connected, select the “Air + Cable”.

In Cable mode, you can select the correct signal source among STD, HRC, and IRC

by pressing the

 or  button, then press the ENTER button.

Contact your local cable company to identify the type of cable system that exists in your

particular area.

4. The TV will begin memorizing all of the available channels.

After all the available channels are stored, the Auto program menu reappears.

Press the ENTER button when channel memorization is complete.

“Select the clock mode.” menu is automatically displayed.

To stop the search before it has finished, press the ENTER button with stop selected.

5. Press the ENTER button.

Press the  or  buttons to select “Manual” or “Auto”, then the ENTER button.

Switches the Daylight Saving Time function on or off.

Operation

BN68-00883V-00Eng.qxd 10/1/04 10:57 PM Page 13

English-14

6. Press the ENTER button.

Press the

 or  buttons to select “Yes” or “No”, then the ENTER button.

“Select the time zone in which you live” menu is automatically displayed.

7. Press the  or  buttons to highlight the time zone for your local area (and to

move the highlight to the appropriate time zone on the map of the United States).

Press the ENTER button. If you have received a digital signal, the time will

be set automatically.

If not, see page 40 to set the clock.

8. The message “Enjoy your watching.” is displayed.

When you have finished,press the ENTER button.

1. Press the MENU button.

Press the  or  buttons to select “Setup”, then press the ENTER button.

2. Press the  or  buttons to select “Plug & Play”.

Press the ENTER button.

For further details on setting up options, refer to the previous page.

Plug & Play can only be accessed in the TV mode.

If you want to reset this featur

e...

Changing Channels

1. Press the CH or CH button to change channels.

When you press the CH or CH button, the TV changes channels in sequence.

You will see all the channels that the TV has memorized. (The TV must have memorized

at least three channels). You will not see channels that were either erased or not

memorized. See page 16 to memorize channels.

Using the Channel Buttons

1. Press the PRE-CH button.

The TV will switch to the last channel viewed.

To quickly switch between two channels that are far apart, tune to one channel, then

use the number button to select the second channel. Then use the

PRE-CH button to

quickly alternate between them.

Using the PRE-CH Button to select the Previous Channel

BN68-00883V-00Eng.qxd 10/1/04 10:57 PM Page 14

English-15

Viewing the Menus

1. With the power on, press the MENU button.

The main menu appears on the screen. Its left side has five icons:

Input, Picture, Sound, Channel, Setup.

2. Use the  or  buttons to select one of the five icons.

Then press the ENTER button to access the icon’s sub-menu.

3. Press the EXIT button to exit.

The on-screen menus disappear from the screen after about two minutes.

Viewing the Display

1. Press the INFO button on the remote control.

The TV will display the channel, the type of sound,

and the status of certain picture and sound settings.

The display screen disappear after about ten seconds.

The display identifies the current channel and the status of certain audio-video settings.

Press the INFO button once more or wait approximately 10 seconds and it disappears

automatically.

Adjusting the Volume

1. Press the

VOL or VOL

buttons to increase or decrease the volume.

1. Press MUTE button and the sound cuts off.

The word “ ” will appear in the lower-left corner of the screen.

2. To turn mute off, press the MUTE button again, or simply press the

VOL or VOL

buttons.

Using Mute

At any time, you can cut off the sound using the MUTE button.

BN68-00883V-00Eng.qxd 10/1/04 10:57 PM Page 15

English-16

Memorizing the Channels

Your TV can memorize and store all of the available channels for both “off-air” (antenna) and cable channels.

After the available channels are memorized, use the CH or CH buttons to scan through the channels.

This eliminates the need to change channels by entering the channel digits. There are three steps for memorizing channels:

selecting a broadcast source, memorizing the channels (automatic) and adding or deleting channels (channel manager).

Selecting the Video Signal-sour

ce

Before your television can begin memorizing the available channels, you must specify the type of signal source that is connected to the

TV (i.e. an antenna or a cable system).

1. Press the MENU button to display the menu.

Press the  or  buttons to select “Channel”, then press the ENTER button.

2. Press the ENTER button select “Antenna”.

Press the  or  buttons to select “Air” or “Cable”, then press the ENTER button.

Press the EXIT button to exit.

Storing Channels in Memory (Automatic Method)

1. Press the MENU button to display the menu.

Press the  or  buttons to select “Channel”, then press the ENTER button.

2. Press the  or  buttons to select “Auto Program”, then press the ENTER button.

3. Press the  or  buttons to select the antenna connection, then press the

ENTER button.

Air: “Air” antenna signal. / Cable: “Cable” antenna signal. /

Air+Cable: “Air” and “Cable” antenna signals.

4. After all the available channels are stored, the “Auto Program” menu reappears.

Press the

EXIT button to exit.

Alternately, you can press the AUTO PROG. button on the remote control to bring up

the Auto Program menu.

BN68-00883V-00Eng.qxd 10/1/04 10:57 PM Page 16

English-17

Setting Up the Remote to Operate Your VCR

1.

Turn off your VCR.

2.

Press the VCR button on your TV’s remote control.

3.

Press the SET button on your TV’s remote control.

4.

Using the number buttons on your remote control, enter three digits of the VCR code listed on

page 19 of this manual for your brand of VCR. Make sure you enter three digits of the code,

even if the first digit is a “0”. (If more than one code is listed, try the first one.)

5.

Press the POWER button on the remote control. Your VCR should turn on if your remote is

set up correctly.

If your VCR does not turn on after set-up, repeat steps 2, 3 and 4, but try one of the other codes

listed for your brand of VCR. If no other codes are listed, try each VCR code, 000 through 080.

Note on Using Remote Control Modes: VCR

When your remote control is in “ VCR” mode, the volume buttons still control your TV’s volume.

Setting Up Your Remote Control

After it has been set up properly, your remote control can operate in five different modes: TV, VCR, Cable, DVD, or Set-Top Box.

Pressing the corresponding button on the remote control allows you to switch between these modes, and control whichever piece of

equipment you choose.

The remote control might not be compatible with all DVD Players, VCRs, Cable boxes, and Set-Top Boxes.

Setting Up the Remote to Operate Your Cable Box

1.

Turn off your cable box.

2.

Press the CABLE button on your TV’s remote control.

3.

Press the SET button on your TV’s remote control.

4.

Using the number buttons on your remote control, enter three digits of the cable box code

listed on page 20 of this manual for your brand of cable box. Make sure you enter three digits

of the code, even if the first digit is a “0”. (If more than one code is listed, try the first one.)

5.

Press the POWER button on the remote control.

Your cable box should turn on if your remote is set up correctly.

If your cable box does not turn on after set-up, repeat steps 2, 3 and 4, but try one of the other

codes listed for your brand of cable box. If no other codes are listed, try each code,

000 through 046.

Note on Using Remote Control Modes: Cable Box

When your remote control is in “ CABLE” mode, the volume buttons still control your TV’s volume.

BN68-00883V-00Eng.qxd 10/1/04 10:57 PM Page 17

English-18

Setting Up the Remote to Operate Your DVD

1.

Turn off your DVD.

2.

Press the DVD button on your TV’s remote control.

3.

Press the SET button on your TV’s remote control.

4.

Using the number buttons on your remote control, enter three digits of the DVD code listed on

page 20~21 of this manual for your brand of DVD. Make sure you enter three digits of the code,

even if the first digit is a “0”. (If more than one code is listed, try the first one.)

5.

Press the POWER button on the remote control.

Your DVD should turn on if your remote is set up correctly.

If your DVD does not turn on after set-up, repeat steps 2, 3 and 4, but try one of the other codes

listed for your brand of DVD. If no other codes are listed, try each code, 000 through 141.

Note on Using Remote Control Modes: DVD

When your remote control is in “DVD” mode, the volume buttons still control your TV’s volume.

Setting Up the Remote to Operate Your Set Top Box

1.

Turn off your STB.

2.

Press the STB button on your TV’s remote control.

3.

Press the SET button on your TV’s remote control.

4.

Using the number buttons on your remote control, enter three digits of the STB code listed on

page 21 of this manual for your brand of STB. Make sure you enter three digits of the code, even

if the first digit is a “0”. (If more than one code is listed, try the first one.)

5.

Press the POWER button on the remote control.

Your STB should turn on if your remote is set up correctly.

If your STB does not turn on after set-up, repeat steps 2, 3 and 4, but try one of the other codes

listed for your brand of STB. If no other codes are listed, try each code, 000 through 074.

Note on Using Remote Control Modes: STB

When your remote control is in “STB” mode, the volume buttons still control your TV’s volume.

BN68-00883V-00Eng.qxd 10/1/04 10:57 PM Page 18

La page charge ...

Samsung LN-S3238D Le manuel du propriétaire

Ce manuel convient également à

Samsung LN-S3238D Le manuel du propriétaire

dans d''autres langues

Documents connexes