Thermador T18ID900LP Manuel utilisateur

Taper
Manuel utilisateur

Ce manuel convient également à

USE & CARE GUIDE
GUIDE
D’UTILISATION
ET D’ENTRETIEN
MANUAL DE USO
Y CUIDADO
Model/Modele/Modelo
T18ID900RP
T18ID900LP
T24ID900RP
T24ID900LP
Freezer
Congélateur
Congelador
en-us
2
enTable of Contents
en Instruction manual
( Important safety instructions . . . . . . . . . . . . 3
Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
About these instructions . . . . . . . . . . . . . . . . . . . . . 3
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Risk of explosion. . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Risk of electric shock . . . . . . . . . . . . . . . . . . . . . . . 3
Risk of cold burns . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Risk of Injury . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Avoiding placing children and vulnerable
people at risk . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Damage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
State of California Proposition 65 Warnings . . . . . . 4
8 Intended use . . . . . . . . . . . . . . . . . . . . . . . . . . 5
7 Environmental protection. . . . . . . . . . . . . . . . 5
Packaging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Old appliances . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
5 Installation and connection . . . . . . . . . . . . . . 5
Contents of package. . . . . . . . . . . . . . . . . . . . . . . . 5
Technical data. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Installing the appliance . . . . . . . . . . . . . . . . . . . . . . 5
Check built-in cut-out. . . . . . . . . . . . . . . . . . . . . . . . 5
Side-by-side installation . . . . . . . . . . . . . . . . . . . . . . 5
Saving energy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Before using for the first time . . . . . . . . . . . . . . . . . 7
Water connection . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Electrical connection . . . . . . . . . . . . . . . . . . . . . . . . 7
* Getting to know your appliance. . . . . . . . . . . 8
Appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Operating controls. . . . . . . . . . . . . . . . . . . . . . . . . . 8
Ice and water dispenser . . . . . . . . . . . . . . . . . . . . . 9
Interior fittings . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
1 Operating the appliance . . . . . . . . . . . . . . . . 14
Switching the appliance on . . . . . . . . . . . . . . . . . .14
Switching off and disconnecting
the appliance. . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Setting the language . . . . . . . . . . . . . . . . . . . . . . .14
Setting the temperature unit . . . . . . . . . . . . . . . . . 14
Setting the temperature. . . . . . . . . . . . . . . . . . . . .14
Super freezing . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Clean lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Switching ice cube production on and off . . . . . . . 15
Reset water filter counter. . . . . . . . . . . . . . . . . . . . 15
Eco mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Self-test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Setting the brightness of the control panel . . . . . . 16
Switching key press sound on or off . . . . . . . . . . . 16
Setting the key volume . . . . . . . . . . . . . . . . . . . . . 16
Setting the signal tone volume . . . . . . . . . . . . . . . 16
Automatic clean lock . . . . . . . . . . . . . . . . . . . . . . 16
Automatic door opening . . . . . . . . . . . . . . . . . . . . 16
Switching the water filter counter
on and off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Dispenser light . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Motion sensor. . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Theater mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Resetting to the factory settings . . . . . . . . . . . . . . 17
Switching demo mode on or off . . . . . . . . . . . . . . 18
Sabbath mode . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
M Alarm. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Door alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
W Freezer compartment. . . . . . . . . . . . . . . . . . 18
Fully utilizing the freezer volume. . . . . . . . . . . . . . 18
Purchasing frozen food. . . . . . . . . . . . . . . . . . . . . 18
When loading products . . . . . . . . . . . . . . . . . . . . 19
Freezing fresh food. . . . . . . . . . . . . . . . . . . . . . . . 19
Thawing frozen food . . . . . . . . . . . . . . . . . . . . . . . 19
; Ice and water dispenser . . . . . . . . . . . . . . . 20
Before using for the first time . . . . . . . . . . . . . . . . 20
Observing drinking water quality . . . . . . . . . . . . . 20
Information on operation of the ice maker . . . . . . 20
Dispensing ice and water . . . . . . . . . . . . . . . . . . . 20
= Defrosting . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Freezer compartment . . . . . . . . . . . . . . . . . . . . . . 21
D Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Care instructions for stainless
steel surfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Cleaning the display . . . . . . . . . . . . . . . . . . . . . . . 21
Cleaning the fittings . . . . . . . . . . . . . . . . . . . . . . . 22
> Noises . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Normal noises . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Preventing noises . . . . . . . . . . . . . . . . . . . . . . . . . 22
9 Lighting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
3 Faults – what to do? . . . . . . . . . . . . . . . . . . 23
Appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Dispenser . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
4 Customer service. . . . . . . . . . . . . . . . . . . . . 25
Appliance self-test . . . . . . . . . . . . . . . . . . . . . . . . 25
Repair order and advice on faults . . . . . . . . . . . . 25
9 Important safety instructions
READ INSTRUCTIONS - DO NOT DISCARD!
Important safety instructions en-us
3
(Important safety instructions
Important safety instructions
READ INSTRUCTIONS - DO NOT DISCARD!
Definitions
9 WARNING
Non-observance of this warning could
result in death or serious injuries.
9 CAUTION!
Non-observance of this warning could
result in slight or moderately serious
injuries.
NOTICE: Non-observance of this
information could damage the appliance.
Note: This indicates important information
and/or tips.
About these instructions
Read and follow the operating and
installation instructions. They contain
important information on how to install,
use and maintain the appliance.
The manufacturer is not liable if you
disregard the instructions and warnings
in the operating and installation
instructions.
Retain all documents for subsequent use
or for the next owner.
Introduction
This appliance complies with the relevant
safety regulations for electrical
appliances.
The refrigeration circuit has been
checked for leaks.
Risk of explosion
Never use electric devices inside the
appliance (e.g. heaters or electric ice
makers).
Do not store products which contain
flammable propellants (e.g. spray cans)
or explosive substances in the appliance.
Only store high-proof alcohol tightly
closed and standing up.
Risk of electric shock
Improper installations and repairs may put
the user at considerable risk.
If the power cord is damaged:
Immediately disconnect the appliance
from the power supply.
Do not use multiple outlets, extension
leads or adapters.
Before servicing or modifying the
appliance, pull out the power plug or
switch off the circuit breaker.
Before cleaning the appliance, press the
main On/Off switch to switch the
appliance off.
Glass shelves or other fittings can be
safely moved while the appliance is
switched on.
Never cut through or remove the third
(ground) conductor of the power cord.
Never defrost or clean the appliance with
a steam cleaner. The steam may
penetrate electrical parts and cause a
short circuit.
Have the appliance, cable and
accessories repaired or replaced by the
manufacturer, Customer Service or a
similarly qualified person only.
Use original parts supplied by the
manufacturer only.
The manufacturer guarantees that these
parts satisfy the safety requirements.
9 Important safety instructions
READ INSTRUCTIONS - DO NOT DISCARD!
en-us Important safety instructions
4
Risk of cold burns
Never put frozen food straight from the
freezer compartment into your mouth.
Avoid prolonged contact of skin with
frozen food, ice and the tubes in the
freezer compartment.
Risk of Injury
Containers which contain carbonated drinks
may burst.
Do not store containers which contain
carbonated drinks in the freezer
compartment.
Avoiding placing children and vulnerable
people at risk
At risk are:
Children,
People who have limited physical, mental
or sensory abilities,
People who have inadequate knowledge
concerning safe operation of the
appliance.
Measures:
Never allow children to play with the
appliance.
Ensure that children and vulnerable
people have understood the hazards.
Supervise children who are cleaning and
maintaining the appliance.
Risk of suffocation
If the appliance features a door lock:
keep the key out of the reach of children.
Keep children away from the packaging
and its parts.
Damage
To prevent damage:
Do not stand or support yourself on the
base, runners or doors.
Keep plastic parts and door seals free of
oil and grease.
Pull the power cord plug – not the power
cord.
Weight
The appliance is very heavy. The appliance
should always be transported and set up by
at least 2 people.
~ "Installation and connection" on page 5
State of California Proposition 65
Warnings
9 WARNING
This product contains chemicals known
to the State of California to cause
cancer, birth defects or other
reproductive harm.
Intended use en-us
5
8Intended use
Intended use
Use this appliance
only for freezing food, making ice and dispensing
drinking water.
only in the home and in the home environment.
only according to these operating instructions.
This appliance is intended for use at an elevation of
no more than 2000 meters above sea level.
7Environmental protection
Environmental protection
Packaging
All materials are environmentally safe and
recyclable:
Dispose of packaging in an environmentally
responsible manner.
Please ask your dealer or inquire at your local
authority about current means of disposal.
Old appliances
Valuable raw materials can be reclaimed by
recycling old appliances.
9 WARNING
CHILDREN MAY BECOME LOCKED IN THE
APPLIANCE AND SUFFOCATE!
Before disposing of your old appliance:
Remove the door.
Leave shelves and containers in the
appliance to prevent children from climbing
in.
Keep children away from the discarded
appliance.
9 CAUTION!
REFRIGERANT AND HARMFUL GASES MAY
ESCAPE.
Do not damage the tubes of the refrigeration
circuit and insulation.
1. Pull out the power cord plug.
2. Cut through the power cord.
3. Have the appliance disposed of properly.
5 Installation and
connection
Installation and connection
Contents of package
After unpacking all parts, check for any damage
during transport.
If you have any complaints, please contact the
dealer from whom you purchased the appliance or
our customer service.
~ "Customer service" on page 25
The delivery consists of the following parts:
Built-in appliance
Interior fittings (depending on model)
Installation material
Instruction manual
Installation instructions
Customer service booklet
Guarantee enclosure
Information on the energy consumption and
noises
Technical data
Refrigerant, cubic capacity and further technical
specifications can be found on the rating plate.
~ "Getting to know your appliance" on page 8
Installing the appliance
Installation location
The weight of the appliance may be up to 460 kg
depending on the model. The base must be
sufficiently stable and should not give. If necessary,
reinforce the bottom.
Check built-in cut-out
The cut-out must fulfill these criteria:
Anti-tilt bracket must be fitted
Cut-out depth min. 24” (610 mm), for flush
installation 25” (635 mm)
rectangular
stable – the side panels and the top must be min.
5/8" (16 mm) thick and securely attached to the
floor or wall
Depth of shortest side panels min. 4” (100 mm)
Side-by-side installation
Observe the specifications in the installation
instructions for a side-by-side installation.
If a partition wall is required between the appliances
it must be at least 5/8" (16 mm) wide.
en-us Installation and connection
6
Saving energy
If you follow the instructions below, your appliance will use less power.
Note:
The arrangement of the fittings does not affect the energy consumption of the appliance.
--------
Installing the appliance
Keep the appliance out of direct sunlight. The appliance needs to cool less frequently at low ambient tempera-
tures and therefore consumes less power.
Install the appliance as far away as possible from heating elements,
cooker and other heat sources:
At least 1¼” (3 cm) from electric or gas cookers.
At least 11¾" (30 cm) from oil or solid-fuel cookers.
NOTICE: If this is not possible, attach an insulating plate between the
appliance and heat source.
Select an installation location at a room temperature of approx. 68 °F
(20 °C).
Do not cover or block the ventilation openings. The appliance needs to cool less frequently if the warm air can
escape and therefore consumes less power.
Ventilate the room daily.
Using the appliance
Open the appliance door only briefly. The air in the appliance does not warm up so intensely. The appliance
needs to cool less frequently and therefore consumes less power.
Transport purchased food in a cool bag and place in the appliance
quickly.
Allow warm food and drinks to cool down before placing in the appli-
ance.
Thaw frozen food in the refrigerator compartment to utilize the low
temperature of the frozen food.
Always leave a space between the food and the back panel. The air can circulate and the humidity will remain constant.The appli-
ance needs to cool less frequently and therefore consumes less
power.
Pack food airtight.
Do not cover or block the ventilation openings. The appliance consumes less power if the warm air can escape.
Vacuum the ventilation openings once a year.
Installation and connection en-us
7
Before using for the first time
1. Remove information material, adhesive tape and
protective foil.
2. Clean the appliance.
~ "Cleaning" on page 21
Water connection
9 CAUTION!
Installation and connection of the appliance
must be carried out by authorized technicians
according to the installation instructions
supplied.
To avoid damage to the appliance and to
ensure its proper functioning, it should only be
connected to a drinking water system.
To avoid water damage, a shut-off valve must
be installed.
Water pressure of drinking water system
9 CAUTION!
To avoid damage to the appliance, a pressure
relief valve must be installed between the
drinking water connection and the tubing,
should the water pressure exceed the
maximum value.
Note: If the water pressure is too low, this will impair
the relevant functions of the appliance.
Min. 0.2 Mpa (2 bar / 29 psi)
Max. 0.8 Mpa (8 bar / 116 psi)
Electrical connection
9 CAUTION!
Do not connect the appliance to electronic
energy saver plugs.
Note: You can connect the appliance to mains-
controlled and sine-controlled inverters.
Mains-controlled inverters are used for photovoltaic
systems which are connected directly to the national
grid. Sine-controlled inverters must be used for
isolated applications. Isolated applications, e.g. on
ships or in mountain lodges, are not directly
connected to the national grid.
1. After installing the appliance, wait at least 1 hour
before connecting it to prevent damaging the
compressor.
2. Connect the appliance via a correctly installed
outlet.
9 WARNING
RISK OF ELECTRIC SHOCK!
Never use multiple outlets, extension leads
or adapters.
The appliance must be correctly grounded.
Never cut through or remove the third
(ground) conductor of the power cord.
Requirements for outlets
Maximum simultaneous load
3. Connect the appliance to an outlet near the
appliance.
The outlet must also be freely accessible
following installation of the appliance.
9 WARNING
RISK OF ELECTRIC SHOCK!
If the length of the power cord is inadequate,
never use multiple outlets or extension
leads.Instead, please contact Customer
Service for alternatives.
Outlet with 110 V ... 120 V
Protective conductor 60 Hz
Fuse 10 A ... 16 A
Appliance 6 A
en-us Getting to know your appliance
8
*Getting to know your
appliance
Getting to know your appliance
Appliance
Operating controls
Settings menu
Press " button to open the menu.
In the Settings menu, you will find:
Appliance settings
Clean lock
Ice cube production
Reset water filter
Eco mode
Self-test
Sabbath mode (if activated)
~ "Operating the appliance" on page 14
( ... H Operating controls
P Main On/Off switch
X Ice maker
` Ice cube container
h Rating plate
)" Frozen food container
)* Automatic door opening
)2 Ventilation opening
): Water filter
)B ... 1" Dispenser
( Touch fields
There are sensors under the touch fields.
Touching the symbol calls up the respective
function.
0 Freezer compartment temperature display
Indicates the set temperature in °F/°C.
8 +/- buttons
Used to change the temperature.
@ " button
Opens the Settings menu.
~ "Settings menu" on page 8
H Super Freeze button
Switches Super Freeze on or off.

6XSHU)UHH]H
C
²
6H WWLQJV
#
+
Getting to know your appliance en-us
9
Appliance settings menu
This is how to navigate to the Appliance settings
menu:
1. Press the " button.
2. Scroll to the left to the Appliance settings menu.
3. Open the menu using the 8 button.
In the Appliance settings menu, you will find the
following sub-menus and setting options:
Brightness
Key press sound
Key volume
Signal tone volume
Automatic clean lock
Automatic door opening
Water filter counter
Dispenser light
Motion sensor
Theater mode
Temperature unit
Language
Factory settings
Demo mode
Sabbath mode
~ "Operating the appliance" on page 14
Ice and water dispenser
)B WATER button
Starts water dispensing.
)J CUBED button
Starts ice cube dispensing.
)R CRUSHED button
Starts dispensing crushed ice.
)Z LOCK button
Locks controls for dispenser panel lock
(child lock). To switch on or off, hold down
for 3 seconds.
)b Ice and water dispenser control panel
)j Grate for drips
1" Drip tray
5

M
E
=% -
en-us Getting to know your appliance
10
Interior fittings
Storage compartment
You can remove and adjust the height of the storage
compartments:
1. Lift up the storage compartment and remove.
2. When re-inserting, insert hooks on back of
storage compartment at same height to make it
level.
Note: Insert the storage compartment carefully to
avoid scratching the appliance.
Shelf
You can remove and adjust the shelf:
1. Lift shelf and remove.
2. When re-inserting, insert hooks on back of shelf
at same height to make it level.
Note: Insert shelf carefully to avoid scratching the
appliance.
Container
You can remove the container:
Press container to the rear,
lift the container at the rear and remove.
You can insert the container:
Pull out telescopic rails all the way
Place the container on the telescopic rails and
push into the appliance until it engages.
Ice pack
In the event of a power failure or a fault:
The ice pack delays the warming of stored frozen
food.
Note: The longest storage time is obtained by
placing the ice pack on the food in the top
compartment.
You can take out the ice pack to temporarily keep
food cool, e.g. in a cool bag.
Getting to know your appliance en-us
11
Ice maker
9 CAUTION!
DAMAGE TO THE APPLIANCE!
Never store bottles or food in the ice cube
container, even for short periods. This can
block and damage the ice maker.
Ice cube production starts as soon as the appliance
has reached the set temperature.
Note: Ice cube production stops automatically when
the ice cube container is full.
Information about switching ice cube production on
and off
~ "Switching ice cube production on and off"
on page 15
Water filter
The water filter must be replaced after 6 months at
the latest.
If the ice tastes stale, discard the rest of the ice
cubes and the ones produced over the next 24
hours. If the ice still tastes stale, change the water
filter.
A new water filter or a particle filter can be obtained
from customer service or a specialist dealer.
Note: You can also use the appliance without a
water filter. Replace the water filter with a particle
filter and switch the water filter counter off. There is
no need to change the particle filter.
Changing the water filter or replacing with a
particle filter
You can change the water filter, or replace it with a
particle filter. The particle filter can remain in the
appliance permanently: it does not need to be
changed.
Note: After installing a new water filter, discard all ice
cubes produced over the first 24 hours.
1. Turn the cap of the water filter clockwise.
2. Take the water filter out.
3. Remove the protective cap of the new filter.
4. Take off the cap of the old water filter and put it
on the new filter.
5. Slide the new filter to the stop in the filter
opening.
Note: The cap must be horizontal here.
6. Turn the water filter counterclockwise to the stop.
7. When using a water filter: Reset water filter
counter.
~ "Reset water filter counter" on page 15
When using a particle filter: Switch off the water
filter counter.
~ "Switching the water filter counter on and off"
on page 15
8. Discard the ice cubes produced over the first 24
hours.
9. Drain the water out of the old water filter.
Note: You can dispose of the old water filter with
your household garbage.
en-us Getting to know your appliance
12
Specification and Performance Data Sheet
Only for appliances with filter model: 9000 777 508
When using replacement cartridge: 9000 674 655
The concentration of the indicated substances
dissolved in water entering the system was reduced
to a concentration less than or equal to the
permissible limit for water leaving the system as
specified in ANSI/NSF Standard 42 and Standard
53.
Capacity: 739.68 gallons/2,800 liters
Contaminant Reduction Determined by NSF testing.
* Based on the use of Cryptosporidium parvum
oocysts.
It is essential that the manufacturer's recommended
installation, maintenance and filter replacement
requirements are carried out as specified. See
manufacturer's documentation for warranty
information.
Note: While the testing was performed under
standard laboratory conditions, actual performance
may vary.
More detailed information on the prices of spare
parts is available from your local appliance dealer or
parts vendor.
9 WARNING
TO REDUCE THE RISK ASSOCIATED WITH
INGESTION OF CONTAMINANTS:!
Do not use with water that is microbiologically
unsafe or of unknown quality without adequate
disinfection before and after connection to the
system. Systems certified for cyst reduction
may be used on disinfected water that may
contain filterable cysts.
EPA Establishment Number 10350-MN-005
System tested and certified by NSF
International against ANSI/NSF Standard
53 and Standard 42 for the reduction of
the claims specified on this Specification
and Performance Data Sheet.
Contaminant Reduction Chlorine Taste and
Odor
Nominal Particulate Class 1,
>/= 0.5 to <1.0 μm
Cysts* Turbidity
Average Influent 2.1 mg/L 9,100,000 pts/mL 170,000 cysts/L 11 NTU
NSF specified Challenge Concentration 2.0 mg/L +/- 10% At least 10,000 particles/mL Minimum
50,000 cysts/L
11 +/- 1 NTU
Avg. % Reduction 97.6% 98.8% 99.99% 98.1%
Average Product Water Concentration 0.05 mg/L 111,817 pts/mL 0.001 cyst/L <1 NTU
Max. Permissible Product Water Concen-
tration
N/A N/A N/A 0.5 NTU
NSF Reduction Requirements >/=50% >/=85% >/=99.95% 95%
NSF Test Report J-00121313 J-00099871 J-00109715 J-00099885
Application Guidelines/Water Supply Parameters
Service Flow 0.75 gpm
(2.83 lpm)
Water Supply Potable Water
Water Pressure 30 ... 120 psi
207 ... 827 kPa
Water Temperature* 33 °F ... 100 °F
0.6 °C ... 38 °C
Getting to know your appliance en-us
13
9 CAUTION!
To reduce the risks associated with property
damage due to water leakage:
Read and follow user instructions before
installation and use of this system.
Installation and use must comply with all state
and local plumbing codes.
Do not install if water pressure exceeds
120 psi/827 kPa. If your water pressure
exceeds 80 psi, you must install a pressure
limiting valve.
Contact a plumbing professional if you are
uncertain how to check your water pressure.
Do not install where water hammer conditions
may occur. If water hammer conditions exist,
you must install a water hammer arrester.
Contact a plumbing professional if you are
uncertain how to check for this condition.
Do not install on hot water supply lines. The
maximum operating water temperature of this
filter system is 100 °F (38 °C).
Protect filter from freezing. Drain filter when
temperatures drop below 33 °F (1 °C).
The disposable filter cartridge must be
replaced
no later than every 6 months at the rated
capacity, or if a noticeable reduction in flow
rate occurs.
Manufactured by:
3M Purification Inc.
400 Research Parkway
Meriden, Ct 06450
Tel. (800) 222-7880
Tel. (203) 237-5541
3M is a trademark of 3M Company used under
license.
NSF is a trademark of NSF International.
© 2013 3M Company. All rights reserved.
en-us Operating the appliance
14
1Operating the appliance
Operating the appliance
Switching the appliance on
1. Press the main On/Off switch.
The appliance starts cooling and the light is
switched on when the door is open.
2. Set the required temperature.
~ "Setting the temperature" on page 14
Operating tips
When the appliance has been switched on, it may
take several hours until the set temperatures have
been reached. Do not put in any food until the
selected temperature has been reached.
The fully automatic NoFrost system ensures that
the freezer compartment remains free of ice.
Defrosting is not required.
The front sides of the housing are partly heated
slightly. This prevents condensation in the area
of the door seal.
If the freezer compartment door cannot be
immediately re-opened after it has been closed,
wait until the resulting low pressure has
equalized.
Switching off and disconnecting the
appliance
Switching off the appliance
Press the main On/Off switch.
The appliance is no longer cooling.
Disconnecting the appliance
9 CAUTION!
Deterioration in water quality
The water supply must be turned off 3 hours
before disconnecting. This prevents mold
forming with any unused water.
If you do not use the appliance for a prolonged
period:
1. Turn off the water supply to the appliance and
wait 3 hours.
2. Remove groceries.
3. Press the main On/Off switch.
4. Pull out the mains plug or switch off the fuse.
The appliance is no longer cooling.
5. Empty the ice cube container and clean the
appliance.
~ "Cleaning" on page 21
6. Leave appliance open.
Setting the language
1. Press " button to open the Settings menu.
2. Press < button to move to the menu item
Appliance settings.
3. Press 8 button.
4. Press < button to move to the menu item
Language.
5. Press " button.
6. Use < > buttons to move to the required
language.
7. Press 8 button.
The display restarts, and the start screen is
displayed.
Setting the temperature unit
You can choose between the unit °C and °F.
1° <=> 1 °F
1 °C <=> 1 °C
1. Press " button to open the Settings menu.
2. Press < button to move to the menu item
Appliance settings.
3. Press 8 button.
4. Use < button to move to the menu item
Temperature unit.
5. Press " button.
6. Use < > buttons to move to the required unit.
7. Press 8 button.
The unit will be changed.
8. Press ; button to exit the menu.
Setting the temperature
Recommended temperature
Freezer compartment
Keep pressing +/- button until the display
indicates the required temperature.
Super freezing
Super freezing cools the freezer compartment as
cold as possible.
Switch on super freezing, e.g.:
to freeze food solid as quickly as possible
4 ... 6 hours before freezing food weighing 2 kg
or more
to use the max. freezing capacity
Note: When super freezing is switched on, increased
operating noises may occur.
After approx. 2 ^ days the appliance switches to
normal operation.
Switching super freezing on or off
Press ]/ã button.
Freezer compartment: 0 °F (-18 °C)
Operating the appliance en-us
15
Clean lock
You can use this function to switch off the touch
function of the controls for 10 seconds. During this
time you can clean the display.
~ "Cleaning the display" on page 21
1. Press " button to open the Settings menu.
2. Press < button.
The cleaning display appears, and the countdown
starts.
Automatic clean lock
You can use this function to select whether the
automatic clean lock is switched on automatically
when the door is opened.
1. Press " button to open the Settings menu.
2. Press < button to move to the menu item
Appliance settings.
3. Press 8 button.
4. Press > button to move to the menu item
Automatic clean lock.
5. To change the setting, press " button.
Switching ice cube production on and off
9 CAUTION!
Damage to the appliance!
Never store bottles or food in the ice cube
container, even for short periods. This can
block and damage the ice maker.
Ice cube production starts as soon as the appliance
has reached the set temperature.
Note: Ice cube production stops automatically when
the ice cube container is full.
Switching ice maker on or off
1. Press " button to open the Settings menu.
2. Use > button to move to the menu item Ice cube
production.
3. Press </= button.
Reset water filter counter
After replacing the water filter, you have to reset the
water filter counter.
1. Press " button to open the Settings menu.
2. Press > button to move to the menu item Reset
water filter counter.
3. Press 8 button to confirm, and confirm the query
again with 8 button.
Note: The water filter counter will not be reset if you
abort the query or take longer than 10 seconds to
make an input.
Switching the water filter counter on and off
If you have replaced the water filter with a particle
filter, switch the water filter counter off. It is not
needed in this case as the particle filter does not
have to be replaced.
1. Press " button to open the Settings menu.
2. Scroll to the left to the Appliance settings menu.
3. Press 8 button.
4. Press > button to move to the menu item Water
filter counter.
5. To change the setting, press " button.
Eco mode
Eco mode switches the appliance to energy-saving
operation.
The appliance automatically sets the following
temperatures:
Freezer compartment: +3 °F (-16 °C)
Switching Eco mode on or off
1. Press the " button to open the Settings menu.
2. Use > button to move to the menu item Eco
mode.
3. Press </= button.
The temperature is changed, and the display shows
the new temperature. When Eco mode is switched
off, the recommended temperature is set.
Note: You can also switch Eco mode on or off by
adjusting the temperature with the +/- buttons.
Self-test
This function can be used to start fault analysis on
your appliance.
~ "Appliance self-test" on page 25
en-us Operating the appliance
16
Setting the brightness of the control panel
1. Press " button to open the Settings menu.
2. Press < button to move to the menu item
Appliance settings.
3. Press 8 button.
4. Press " button to open the menu item
Brightness.
5. Use < > buttons to set the required brightness.
6. Press 8 button.
The setting is saved.
7. Press ; button to exit the menu.
Switching key press sound on or off
You can switch the sounds generated when pressing
keys off and back on again.
1. Press " button to open the Settings menu.
2. Press < button to move to the menu item
Appliance settings.
3. Press 8 button to open the menu item.
4. Press > button to move to the menu item Key
press sound.
5. Press " button to open the menu item.
6. Use < > buttons to select the required setting.
7. Press 8 button.
The setting is saved.
8. Press ; button to exit the menu.
Setting the key volume
You can adjust the volume level of the sounds
generated when pressing keys.
1. Press " button to open the Settings menu.
2. Press < button to move to the menu item
Appliance settings.
3. Press 8 button to open the menu item.
4. Press > button to move to the menu item Key
volume.
5. Press " button to open the menu item.
6. Use < > buttons to select the required setting.
7. Press 8 button.
The setting is saved.
8. Press ; button to exit the menu.
Setting the signal tone volume
You can adjust the volume level of the signal tones
generated e.g. with alarms.
1. Press " button to open the Settings menu.
2. Press < button to move to the menu item
Appliance settings.
3. Press 8 button to open the menu item.
4. Use > button to move to the menu item Signal
tone volume.
5. Press " button to open the menu item.
6. Use < > buttons to select the required setting.
7. Press 8 button.
The setting is saved.
8. Press ; button to exit the menu.
Automatic clean lock
You can use this function to select whether the
automatic clean lock is switched on automatically
when the door is opened.
1. Press " button to open the Settings menu.
2. Press < button to move to the menu item
Appliance settings.
3. Press 8 button.
4. Press > button to move to the menu item
Automatic clean lock.
5. To change the setting, press " button.
Automatic door opening
9 CAUTION!
Repeatedly closing the door too early will cause
automatic door opening to fail or wear out.
Do not close the door as long as automatic
door opening is still moved out.
If you have however closed the door, leave it
closed for 5 minutes. Automatic door opening
will re-adjust itself.
The automatic door opening function supports you in
opening the door. As soon as you activate this
function, automatic door opening moves out and
supports you in opening the door.
Open the menu item Aut. door opening:
1. Press " button.
2. Press < button to move to the menu item
Appliance settings.
3. Press 8 button to open the menu item.
4. Use > button to move to the menu item Aut. door
opening.
5. To change the setting, press " button.
Switching on Push-to-open system
In an installation situation without handles you can
select the Push-to-open system. Your appliance will
then open a crack if you press lightly on the door.
1. Open menu item Aut. door opening.
2. Select menu item Push-to-open system.
3. Press 8 button to open the menu item.
4. Select menu item Opening force. Here you can
select the level of force required to activate
automatic door opening.
5. Select menu item Opening duration. Here you
can select how long the door should remain open
a crack before it closes again automatically.
Note: If the door only remains open a crack, the
appliance checks once a second whether the door
is still ajar. After the selected opening time elapses,
the appliance will close the door automatically.
Operating the appliance en-us
17
Switching on Pull-to-open system
In an installation situation with handles you can
select the Pull-to-open system. Your appliance will
support you in opening the door as soon as you pull
on the handle.
1. Open menu item Aut. door opening.
2. Select menu item Pull-to-open system.
3. Press 8 button to open the menu item.
4. Select menu item Opening force. Here you can
select the level of force required to activate
automatic door opening.
Switching off automatic door opening
1. Open menu item Aut. door opening.
2. Select menu item Off.
3. Press 8 button.
The setting is saved.
Switching the water filter counter on and
off
If you have replaced the water filter with a particle
filter, switch the water filter counter off. It is not
needed in this case as the particle filter does not
have to be replaced.
1. Press " button to open the Settings menu.
2. Scroll to the left to the Appliance settings menu.
3. Press 8 button.
4. Press > button to move to the menu item Water
filter counter.
5. To change the setting, press " button.
Dispenser light
Use this function to set how long the light will
illuminate the ice and water dispenser.
Adjusting dispenser light
1. Press " button to open the Settings menu.
2. Press < button to move to the menu item
Appliance settings.
3. Press 8 button to open the menu item.
4. Press > button to move to the menu item
Dispenser light.
5. Press " button to open the menu item.
6. Press > button to select the required duration.
7. Press 8 button.
The setting is saved.
8. Press ; button to exit the menu.
Motion sensor
When the motion sensor is switched on, the ice and
water dispenser light automatically switches on as
soon as a glass is held underneath.
Switching motion sensor on or off
1. Press " button to open the Settings menu.
2. Press < button to move to the menu item
Appliance settings.
3. Press 8 button to open the menu item.
4. Press > button to move to the menu item Motion
sensor.
5. Press " button to open the menu item.
6. Use the > button to move to the menu item On or
Off.
7. Press 8 button.
The setting is saved.
8. Press ; button to exit the menu.
Theater mode
If Theater mode is switched on, the light will slowly
become brighter when the appliance is opened, and
then slowly darker when it is closed.
Switching Theater mode on or off
1. Press " button to open the Settings menu.
2. Press < button to move to the menu item
Appliance settings.
3. Press 8 button to open the menu item.
4. Use > button to move to the menu item Theater
mode.
5. Press " button to open the menu item.
6. Use > button to move to the menu item On or Off.
7. Press 8 button.
The setting is saved.
8. Press ; button to exit the menu.
Resetting to the factory settings
1. Press " button to open the Settings menu.
2. Press < button to move to the menu item
Appliance settings.
3. Press 8 button.
4. Use < button to move to the menu item Factory
settings.
5. Press " button.
A signal tone sounds, and a message to confirm
reset appears.
6. Press 8 button.
All settings are reset to the factory settings.
7. Press ; button to exit the menu.
en-us Alarm
18
Switching demo mode on or off
The cooling function of the appliance is switched off.
All other functions can be used.
Note: Do not store any food items in demo mode as
the appliance remains at room temperature.
1. Press " button to open the Settings menu.
2. Press < button to move to the menu item
Appliance settings.
3. Press 8 button.
4. Use < button to move to the menu item Demo
mode.
5. Press " button.
6. Use <> buttons to select the setting On or Off
7. Press 8 button.
The setting is saved.
8. Press ; button to exit the menu.
Sabbath mode
The appliance switches off the following:
Automatic door opening
Ice maker
Audible signals
Interior light
Messages on the control panel
Background illumination of control panel is
reduced
Switching Sabbath mode on or off
Displaying Sabbath mode in the Settings menu
To use Sabbath mode, you first have to display the
function in the Settings menu:
1. Press " button to open the Settings menu.
2. Press < button to move to the menu item
Appliance settings.
3. Press 8 button.
4. Press < button to move to the menu item
Sabbath mode. Press " button.
5. Press < button to move to the menu item
Available. Confirm by pressing 8 button.
The function is added to the Settings menu.
Switching on Sabbath mode
1. Press " button to open the Settings menu.
2. Press button to open the view Duration
Sabbath mode.
3. Select one of the presettings or change the
duration with the +/- buttons.
4. Press < button to start.
The appliance switches all listed functions off.
Switching Sabbath mode off
After the selected time elapses, the appliance
switches over to normal operation.
To end Sabbath mode before expiry of the
selected time, press = button.
MAlarm
Alarm
Door alarm
If the appliance door is open for a long time, the
door alarm (continuous audible signal) switches on.
Close door.
The audible warning signal is switched off.
WFreezer compartment
Freezer compartment
The freezer compartment is suitable for:
storing frozen food
making ice cubes
freezing food
The temperature can be set from -11 °F (-
24 °C)... +7 °F (-14 °C).
The freezer compartment can be used to store
perishable foods long-term almost without any
noticeable reduction in quality, as the low
temperatures considerably slow down or stop
deterioration. Appearance, flavor and all valuable
ingredients are largely retained.
The time between putting fresh food in the freezer
compartment and it freezing solid depends on the
following factors:
temperature set
type of food
amount of food in the freezer compartment
quantity and type of storage
Fully utilizing the freezer volume
To place the maximum quantity of frozen food in the
freezer compartment:
Remove all fittings.
Store food directly on the shelves and on the floor
of the freezer compartment.
Purchasing frozen food
Ensure the packaging is not damaged.
Do not exceed the sell-by date.
Temperature in the supermarket freezer must be
0 °F (-18 °C) or lower.
If possible, transport frozen food in a cool bag
and place quickly in the freezer compartment.
Freezer compartment en-us
19
When loading products
Freeze large quantities of food in the top
compartment.
This is where it will freeze especially quickly and
gently.
Distribute food in the compartments or frozen
food containers.
Do not bring food which is to be frozen into
contact with frozen food.
If required, restack frozen food in the frozen food
containers.
Important for unrestricted air circulation in the
appliance:
push in frozen food containers up to the limit
stop.
Freezing fresh food
Freeze only fresh and undamaged food.
Food which is boiled, fried or baked is more suitable
for freezing than food which is eaten raw.
Before freezing food, make preparations appropriate
to the food in order to retain the best possible
nutritional value, flavor and color:
Vegetables: wash, chop, blanch.
Fruit: wash, pit and perhaps peel, possibly add
sugar or ascorbic acid solution.
Information on how to do this can be found in
relevant literature.
Suitable for freezing
Baked goods
Fish and seafood
Meat
Poultry and game
Vegetables, fruit and herbs
Eggs without shells
Dairy products, e.g. cheese, butter and quark
Ready meals and leftovers, e.g. soups, stews,
cooked meat and fish, potato dishes, soufflés and
desserts
Not suitable for freezing
Types of vegetables which are usually eaten raw,
e.g. lettuce or radishes
Unpeeled or hard-boiled eggs
Grapes
Whole apples, pears and peaches
Yoghurt, soured milk, sour cream, creme fraiche
and mayonnaise
Packing frozen food
The correct type of packaging and material selection
are decisive factors in the retention of the product
quality and prevent the development of freezer burn.
1. Place food in packaging.
2. Remove air.
3. Pack food airtight to prevent it from losing flavor
or drying out.
4. Label packaging with contents and date of
freezing.
Suitable packaging:
Plastic foil
Tubular foil made of polyethylene (PE)
Aluminum foil
Freezer containers
Suitable closures:
Rubber bands
Plastic clips
Cold-resistant adhesive tape
Unsuitable packaging:
Wrapping paper
Greaseproof paper
Cellophane
Garbage bags and used grocery bags
Shelf life of frozen food at 0 °F (-18 °C)
Thawing frozen food
The thawing method must be adjusted to the food
and application in order to retain the best possible
product quality.
Thawing methods:
in the refrigerator compartment (especially
suitable for animal-based foods such as fish,
meat, cheese, quark)
at room temperature (bread)
in the microwave (food for immediate
consumption or immediate preparation)
in the oven/cooker (food for immediate
consumption or immediate preparation)
9 CAUTION!
Do not refreeze partly or completely thawed
food. You can only refreeze food once it has
been cooked (boiled or fried).
The frozen food can no longer be stored for the
maximum duration.
Fish, sausage, ready meals, and cakes
and pastries:
up to 6 months
Meat, poultry: up to 8 months
Vegetables, fruit: up to 12 months
en-us Ice and water dispenser
20
;Ice and water dispenser
Ice and water dispenser
You can use the ice and water dispenser to
dispense:
cooled water
crushed ice
ice cubes
Before using for the first time
9 WARNING
RISK OF INJURY!
Never reach into the dispenser opening of the
ice cube container.
9 CAUTION!
Do not place bottles or food in the ice cube
container. This can block and damage the ice
maker.
Notes
The ice and water dispenser only works when the
appliance is connected to a drinking water
pipeline.
Dispose of the first 5 glasses of water and the
first 30-40 ice cubes for hygienic reasons
When the appliance has been connected, there may
be air in the water circuit. Keep dispensing water
until there are no more air bubbles in it.
It takes approx. 24 hours until the first serving of ice
cubes is ready.
Observing drinking water quality
All materials used in the ice and water dispenser are
odorless and tasteless.
If the water has an aftertaste, this may be due to the
following causes:
Mineral content and chlorine content of the
drinking water
Material of the water pipeline
Freshness of the drinking water.
Note: If you dispense water again after a long time, it
may taste stale. In this case, dispose of the first 15
glasses.
You will obtain the best water quality if you dispense
a little water regularly.
The supplied water filter will filter only particles out of
the water, not bacteria or microbes.
Information on operation of the ice maker
Ice cube production starts as soon as the freezer
compartment has reached the set temperature.
The ready ice cubes are automatically discharged
into the ice cube container.
Ice cube production stops as soon as the ice cube
container is full.
Note: You can accelerate ice production by setting a
colder freezer compartment temperature. This will
slightly increase energy consumption.
Dispensing ice and water
Notes
To prevent ice from falling on the floor, hold the
glass directly under the dispenser when
dispensing crushed ice.
To prevent water damage, the water dispenser
automatically stops after 30 seconds of
continuous dispensing. If you want to dispense
more water, wait 5 seconds and press the button
again.
The dispensed water is cooled to a palatable
temperature. To obtain a colder drinking
temperature, put more ice cubes in the glass.
The water may become warmer when dispensing
fairly large amounts of water.
1. Hold the glass under the ice and water dispenser.
2. Keep pressing the dispensing button until the
required quantity of ice or water is in the glass.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77

Thermador T18ID900LP Manuel utilisateur

Taper
Manuel utilisateur
Ce manuel convient également à