Sony XBR-55X800E Le manuel du propriétaire

C-644-100-12(1)

To Customers and Sony Dealers

Wall-Mount Bracket

Installation Manual

Manuel d’installation

Manual de instalación

GB

FR

ES

SU-WL500

2 (GB)

Thank you for purchasing this product.

If the safety precautions are not observed or the

product is used incorrectly, it may result in serious

injury or fire.

This manual shows the correct handling of the

product and important precautions necessary to

prevent accidents. Be sure to read this manual

thoroughly and use the product correctly. Keep this

manual available for future reference.

To Sony dealers

Sufficient expertise is required for installing this

product. Be sure to read this manual thoroughly to do

the installation work safely. Sony is not liable for any

damages or injury caused by mishandling or

improper installation. Please give this manual to the

customer after installation.

Products by Sony are designed with safety in mind. If

the products are used incorrectly, however, it may

result in a serious injury through fire, electric shock,

the product toppling over, or the product dropping.

Be sure to observe the precautions for safety to

prevent such accidents.

Specified products

The following products are subject to change

without notice, may be out of stock, or

discontinued.

Some models may not be available in certain

regions.

To Customers

Sufficient expertise is required for installing this

product. Be sure to subcontract the installation to

Sony dealers or licensed contractors and pay

special attention to safety during the installation.

Sony is not liable for any damages or injury

caused by mishandling or improper installation, or

installing any other than the specified product.

Your Statutory Rights (if any) are not affected.

WARNING

On Safety

CAUTION

LCD Color TV

XBR-75X900E

XBR-65X900E

XBR-55X900E

XBR-49X900E

XBR-75X850E

XBR-65X850E

XBR-55X800E

XBR-49X800E

XBR-43X800E

KD-75X9000E

KD-65X9000E

KD-55X9000E

KD-49X9000E

KD-75X8500E

KD-65X8500E

KD-55X8500E

KD-49X8000E

KD-43X8000E

3 (GB)

GB

English

There are 4 types of installation. It may not be possible to install some types of TVs. Check the following and

install your TV in the adequate way.

AC adaptor holder kit SU-AH1 is not be able to installed.

To install the TV to the wall, the SU-WL500 Wall Mount Bracket is necessary. Screws and spacers listed below are

also necessary depending on the way of installation.

For further details/terms & conditions, contact the sales representative for professional use.

*1

You cannot install the TV other than the noted types.

*2

For the TV with , the following are neccesary.

Spacer: a washer with an outside diameter of 18 mm, inside diameter of 10 mm, and thickness of 2 mm

(SONY Part Number 7-688-000-32) × 20

Screw: PSW M6 × 25 mm (SONY Part Number 4-577-326-01) × 4 (1 pk)

*3

Make brightness setting to Standard or Custom 45 and lower.

*4

Make brightness setting of KD-55X8500E to Standard or Custom 30 and lower.

*5

Make brightness setting to Standard or Custom 35 and lower.

A: Landscape, -20° leaning B: Landscape, +60° leaning C: Portrait, no leaning D: Portrait, +20° leaning

TV model

Installation type

*1

Spacer

*2

Wall-Mount Bracket

Model Qty

XBR-75X900E KD-75X9000E

A 

SU-WL500 1

C 

XBR-65X900E

XBR-55X900E

XBR-49X900E

KD-65X9000E

KD-55X9000E

KD-49X9000E

A

C 

XBR-75X850E KD-75X8500E

A



B*3

XBR-65X850E

KD-65X8500E

KD-55X8500E

A 

B 

C



*4

D



*4

XBR-55X800E

XBR-49X800E

KD-49X8000E

A*5

B*5

C



*5

D



*5

XBR-43X800E KD-43X8000E

C



*5

D



*5

4 (GB)

Be sure to read thoroughly the all safety information

described in the instruction manual of SU-WL500.

Do NOT use SU-WL450 for installation in the way

noted in this manual.

Provide adequate clearances

around the TV.

The following illustration shows how much space is

required around the TV.

Be sure to install the TV in the orientation shown in

the following illustration.

Landscape

Portrait

Do not block the ventilation holes of

the TV.

If you block the ventilation holes with tapes or other

objects, heat builds up inside the TV and may cause a

fire.

• When installing in portrait orientation, only the

following input/output jacks are available:

– HDMI IN 1/2/3/4 (Support 4K resolution, HDCP

2.2-compatible)

– DIGITAL AUDIO OUT (OPTICAL)

–AUDIO OUT / (Stereo mini jack)

– USB 1/2, USB 3

–  LAN

– HDMI1 AUDIO IN (There may be no jack

depending on the country or region.)

• If you cover the illumination LED and its

surroundings with tapes or other objects, the

status of the TV cannot be recognized and the

remote control may not work.

• When carrying the TV, hold it in landscape

orientation, and take care not to drop it when

installing. Do not apply excessive force to the TV;

otherwise, it may be deformed.

WARNING

If the following precautions are not observed,

serious injury or death through fire, electric

shock, the product toppling over, or the

product dropping can result.

Unit: mm (inches)

300

(11

7

/8)

100

(4)

100

(4)

100

(4)

Unit: mm (inches)

300

(11

7

/8)

100

(4)

100

(4)

100

(4)

Others

5 (GB)

Follow Step 1 in the SU-WL500 instruction manual to

check the parts.

Follow Step 2 in the SU-WL500 instruction manual to

decide on the installation location. Refer to page 18

of this manual for the TV installation dimension table.

Follow Step 3 in the SU-WL500 instruction manual to

install the Base Bracket.

A: landscape, -20° leaning

Step 1:

Checking the parts

required for the

installation

Step 2:

Deciding on the

installation location

Step 3:

Installing the Base

Bracket on the wall

Step 4:

Preparing for the

installation of the TV

1

Remove the stand if it is

installed to the TV.

Lay down the TV and lay a soft cloth under the

TV to protect the TV monitor.

XBR-75X900E/XBR-65X900E/XBR-55X900E/

XBR-49X900E/XBR-75X850E/XBR-65X850E/

XBR-55X800E/KD-75X9000E/KD-65X9000E/

KD-55X9000E/KD-49X9000E/KD-75X8500E/

KD-65X8500E/KD-55X8500E

XBR-49X800E/KD-49X8000E

When using an electric screwdriver, set the torque

setting to approximately 2 N·m {20 kgf·cm}.

Do not lift the Mounting Hook before the screws

(two screws each for left/right) are secured. This

may distort the Mounting Hook or the TV cabinet.

6 (GB)

2

Remove the screws from the

rear of the TV.

XBR-75X900E/XBR-65X900E/XBR-55X900E/

XBR-49X900E/XBR-65X850E/KD-75X9000E/

KD-65X9000E/KD-55X9000E/KD-49X9000E/

KD-65X8500E/KD-55X8500E

XBR-75X850E/KD-75X8500E

3

Referring to the Screw and Hook

locations diagram/table on

page 20, determine the screw

positions, and secure the

Mounting Hook to the rear of the

TV.

 Secure the Mounting Hook to the rear of the

TV temporarily, using the four screws

(*1, *2)

.

 Be sure that both screws are securely

tightened with equal torque strength to the

rear of the TV.

*1

Needs 5 spacers (not supplied) and screws

PSW M6 × 25 mm (not supplied):

XBR-75X900E/XBR-75X850E/XBR-65X850E/

KD-75X9000E/KD-75X8500E/KD-65X8500E/

KD-55X8500E

*2

No spacers necessary, but screws of PSW 6 ×

16 mm are necessary (supplied):

XBR-65X900E/XBR-55X900E/XBR-49X900E/

XBR-55X800E/XBR-49X800E/KD-65X9000E/

KD-55X9000E/KD-49X9000E/KD-49X8000E

Mounting Hook

Screw

*1, *2

Spacer

*1, *2

10 mm (13/32 inch)

7 (GB)

4

Adjust the angle of the

Mounting Hook with the

supplied hex key.

Perform following  and . Make sure that

screw  firmly secures the arm base of the

Mounting Hook (both left and right).

 Remove the 2 screws  from the arm base

of the Mounting Hook (both left and right)

and determine the screw holes for the angle

(20°) you plan to change to.

 Fit screw holes of the upper arm  and

lower arm  in an adequate angle, put

screws removed in step  into the holes,

then secure both arms.

Notes

• Make sure that the adjusted angle of both arms are

the same.

• Make sure that both arms are screwed in securely.

CAUTION

• Be careful not to get your fingers caught while

adjusting the angle.

Hex key

Step 5:

Installing the TV on the

wall

WARNING

Be sure to complete the installation before

connecting the AC power cord to the wall outlet. If

you allow the AC power cord to be pinched under

or between pieces of equipment, this may result

in a short circuit or an electric shock.

Be careful not to stumble over the AC power cord

or the TV, as you may hurt yourself.

1

Connect the AC power cord and

the connecting cable(s) supplied

with the TV to the TV.

Connect the AC power cord and the connecting

cable(s) to the connectors on the rear of the TV.

For details on connecting the AC power cord

and the connecting cable(s), refer to the

instruction manual of the TV.

Notes

• You cannot connect the cables to the TV after

installing it on the Base Bracket.

• Subcontract the cable routing in the wall to a

licensed contractor.

8 (GB)

Follow the instructions in the SU-WL500 instruction

manual to confirm.

Follow the instructions in the SU-WL500 instruction

manual to remove.

2

Install the TV onto the Base

Bracket.

 Referring to the Screw and Hook locations

diagram/table on page 20, determine the

holes of the Base Bracket for latching the

upper hooks of the Mounting Hook.

 Hold the TV securely with both hands, and

gently align it on the wall.

WARNING

• Be sure that two or more persons hold the TV when

carrying it.

• When carrying the TV, hold it in landscape

orientation, and take care not to drop it when

installing. Do not apply excessive force to the TV;

otherwise, it may be deformed.

Base Bracket

Mounting Hook

3

Firmly secure the TV and the

Base Bracket using the screw

supplied with SU-WL500

(+BVST4 × 12).

Note

When using an electric screwdriver, set the torque

setting to approximately 1.5 N·m {15 kgf·cm}.

Confirming the

completion of the

installation

When removing the TV

Screw

(+BVST4 × 12)

WARNING

Be sure to tighten the securing screw firmly.

If you fail to do so, the TV may fall when it is

pushed upward and cause injury.

9 (GB)

Follow Step 1 in the SU-WL500 instruction manual to

check the parts.

Follow Step 2 in the SU-WL500 instruction manual to

decide on the installation location. Refer to page 18

of this manual for the TV installation dimension table.

Follow Step 3 in the SU-WL500 instruction manual to

install the Base Bracket.

B: landscape, +60° leaning

Step 1:

Checking the parts

required for the

installation

Step 2:

Deciding on the

installation location

Step 3:

Installing the Base

Bracket on the wall or

mounting

Step 4:

Preparing for the

installation of the TV

1

Remove the stand if it is

installed to the TV.

Lay down the TV and lay a soft cloth under the

TV to protect the TV monitor.

XBR-75X850E/XBR-65X850E/XBR-55X800E/

KD-75X8500E/KD-65X8500E/KD-55X8500E

XBR-49X800E/KD-49X8000E

When using an electric screwdriver, set the torque

setting to approximately 2 N·m {20 kgf·cm}.

Do not lift the Mounting Hook before the screws

(two screws each for left/right) are secured. This

may distort the Mounting Hook or the TV cabinet.

10 (GB)

2

Remove the screws from the

rear of the TV.

XBR-65X850E/KD-65X8500E/KD-55X8500E

XBR-75X850E/KD-75X8500E

3

Referring to the Screw and Hook

locations diagram/table on

page 20, determine the screw

positions, and secure the

Mounting Hook to the rear of the

TV.

 Secure the Mounting Hook to the rear of the

TV temporarily, using the four screws

(*1, *2)

.

 Be sure that both screws are securely

tightened with equal torque strength to the

rear of the TV.

*1

Needs 5 spacers (not supplied) and screws

PSW M6 × 25 mm (not supplied):

XBR-65X850E/KD-65X8500E/KD-55X8500E

*2

No spacers necessary, but screws of PSW 6 ×

16 mm are necessary (supplied):

XBR-75X850E/XBR-55X800E/XBR-49X800E/

KD-75X8500E/KD-49X8000E

Mounting Hook

Screw

*1, *2

Spacer

*1, *2

10 mm (13/32 inch)

11 (GB)

4

Make sure that the screw 

firmly secures the arm base of

the Mounting Hook (both left

and right).

Note

Make sure that the two arms are screwed in securely.

Step 5:

Installing the TV on the

wall

WARNING

Be sure to complete the installation before

connecting the AC power cord to the wall outlet. If

you allow the AC power cord to be pinched under

or between pieces of equipment, this may result

in a short circuit or an electric shock.

Be careful not to stumble over the AC power cord

or the TV, as you may hurt yourself.

1

Connect the AC power cord and

the connecting cable(s) supplied

with the TV to the TV.

Connect the AC power cord and the connecting

cable(s) to the connectors on the rear of the TV.

For details on connecting the AC power cord

and the connecting cable(s), refer to the

instruction manual of the TV.

Notes

• You cannot connect the cables to the TV after

installing it on the Base Bracket.

• Subcontract the cable routing in the wall to a

licensed contractor.

12 (GB)

Follow the instructions in the SU-WL500 instruction

manual to confirm.

Follow the instructions in the SU-WL500 instruction

manual to remove.

2

Install the TV onto the Base

Bracket.

 Referring to the Screw and Hook locations

diagram/table on page 20, determine the

holes of the Base Bracket for latching the

upper hooks of the Mounting Hook.

 Hold the TV securely with both hands, and

gently align it on the wall.

WARNING

• Be sure that two or more persons hold the TV when

carrying it.

• When carrying the TV, hold it in landscape

orientation, and take care not to drop it when

installing. Do not apply excessive force to the TV;

otherwise, it may be deformed.

Base Bracket

Mounting Hook

3

Firmly secure the TV and the

Base Bracket using the screw

supplied with SU-WL500

(+BVST4 × 12).

Note

When using an electric screwdriver, set the torque

setting to approximately 1.5 N·m {15 kgf·cm}.

Confirming the

completion of the

installation

When removing the TV

Screw

(+BVST4 × 12)

WARNING

Be sure to tighten the securing screw firmly.

If you fail to do so, the TV may fall when it is

pushed upward and cause injury.

13 (GB)

Follow Step 1 in the SU-WL500 instruction manual to

check the parts.

Follow Step 2 in the SU-WL500 instruction manual to

decide on the installation location. Refer to page 19

of this manual for the TV installation dimension table.

Follow Step 3 in the SU-WL500 instruction manual to

install the Base Bracket.

C: portrait, no leaning / D: portrait, +20° leaning

Step 1:

Checking the parts

required for the

installation

Step 2:

Deciding on the

installation location

Step 3:

Installing the Base

Bracket on the wall or

mounting

Step 4:

Preparing for the

installation of the TV

1

Remove the stand if it is

installed to the TV.

Lay down the TV and lay a soft cloth under the

TV to protect the TV monitor.

XBR-75X900E/XBR-65X900E/XBR-55X900E/

XBR-49X900E/XBR-65X850E/XBR-55X800E/

KD-75X9000E/KD-65X9000E/KD-55X9000E/

KD-49X9000E/KD-65X8500E/KD-55X8500E

XBR-49X800E/XBR-43X800E/KD-49X8000E/

KD-43X8000E

When using an electric screwdriver, set the torque

setting to approximately 2 N·m {20 kgf·cm}.

Do not lift the Mounting Hook before the screws

(two screws each for left/right) are secured. This

may distort the Mounting Hook or the TV cabinet.

14 (GB)

2

Remove the screws from the

rear of the TV.

XBR-75X900E/XBR-65X900E/XBR-55X900E/

XBR-49X900E/XBR-65X850E/KD-75X9000E/

KD-65X9000E/KD-55X9000E/KD-49X9000E/

KD-65X8500E/KD-55X8500E

3

Referring to the Screw and Hook

locations diagram/table on

page 20, determine the screw

positions, and secure the

Mounting Hook to the rear of the

TV.

 Secure the Mounting Hook to the rear of the

TV temporarily, using the four screws

(+PSW6 × 25).

 Be sure that both screws are securely

tightened with equal torque strength to the

rear of the TV.

Screw

(+PSW6 × 25)

(not supplied)

Mounting

Hook

Spacer × 5

(not supplied)

10 mm (13/32 inch)

4

Make sure that the screw 

firmly secures the arm base of

the Mounting Hook (both left

and right).

Notes

• When installing in portrait orientation, be sure to

keep the Mounting Hook angle to 0 degrees. Do

not use another angles.

• Make sure that the two arm bases are screwed in

securely.

15 (GB)

Step 5:

Installing the TV on the

wall

WARNING

Be sure to complete the installation before

connecting the AC power cord to the wall outlet. If

you allow the AC power cord to be pinched under

or between pieces of equipment, this may result

in a short circuit or an electric shock.

Be careful not to stumble over the AC power cord

or the TV, as you may hurt yourself.

1

Connect the AC power cord and

the connecting cable(s) supplied

with the TV to the TV.

Connect the AC power cord and the connecting

cable(s) to the connectors on the rear of the TV.

For details on connecting the AC power cord

and the connecting cable(s), refer to the

instruction manual of the TV.

Notes

• You cannot connect the cables to the TV after

installing it on the Base Bracket.

• Subcontract the cable routing in the wall to a

licensed contractor.

2

Install the TV onto the Base

Bracket.

 Referring to the Screw and Hook locations

diagram/table on page 20, determine the

holes of the Base Bracket for latching the

upper hooks of the Mounting Hook.

 Hold the TV securely with both hands, and

gently align it on the wall.

WARNING

• Be sure that two or more persons hold the TV when

carrying it.

• When carrying the TV, hold it in landscape

orientation, and take care not to drop it when

installing. Do not apply excessive force to the TV;

otherwise, it may be deformed.

C: Portrait, no leaning

Base Bracket

Mounting Hook

16 (GB)

D: Portrait, +20° leaning

Base Bracket

Mounting Hook

3

Firmly secure the TV and the

Base Bracket using the screw

supplied with SU-WL500

(+BVST4 × 12).

C: Portrait, no leaning

Screw

(+BVST4 × 12)

17 (GB)

Follow the instructions in the SU-WL500 instruction

manual to confirm.

Follow the instructions in the SU-WL500 instruction

manual to remove.

D: Portrait, +20° leaning

Note

When using an electric screwdriver, set the torque

setting to approximately 1.5 N·m {15 kgf·cm}.

Confirming the

completion of the

installation

When removing the TV

Screw

(+BVST4 × 12)

WARNING

Be sure to tighten the securing screw firmly.

If you fail to do so, the TV may fall when it is

pushed upward and cause injury.

18 (GB)

The table below shows the dimensions of the TV that is mounted on this product. Refer to this table to decide

on the installation location.

A: Landscape, -20° leaning

B: Landscape, +60° leaning

Unit: mm (inches)

Some models may not be available in certain regions.

Figures in the above table may differ slightly depending on the installation.

WARNING

The wall that the TV will be installed on should be capable of supporting a weight of at least four times that of

the TV.

Refer to your TV’s instructions for its weight.

TV installation dimensions table

Model Name

Display dimensions

Length for each mounting angle

Angle (20º) Angle (60º)

XBR-75X900E

KD-75X9000E

1,674

(66)

959

(37 7/8)

98

(3 7/8)

549

(21 5/8)

410

(16 1/4)

901

(35 1/2)

————

XBR-65X900E

KD-65X9000E

1,447

(57)

830

(32 3/4)

103

(4 1/8)

494

(19 1/2)

369

(14 5/8)

780

(30 3/4)

————

XBR-55X900E

KD-55X9000E

1,228

(48 3/8)

707

(27 7/8)

161

(6 3/8)

494

(19 1/2)

327

(12 7/8)

664

(26 1/4)

————

XBR-49X900E

KD-49X9000E

1,093

(43 1/8)

631

(24 7/8)

213

(8 1/2)

511

(20 1/8)

297

(11 3/4)

592

(23 3/8)

————

XBR-75X850E

KD-75X8500E

1,677

(66 1/8)

968

(38 1/8)

11

(7/16)

469

(18 1/2)

424

(16 3/4)

910

(35 7/8)

547

(21 5/8)

840

(33 1/8)

527

(20 3/4)

109

(4 3/8)

XBR-65X850E

KD-65X8500E

1,454

(57 1/4)

840

(33 1/8)

121

(4 7/8)

518

(20 1/2)

353

(14)

790

(31 1/8)

411

(16 1/4)

72

9

(28

3/4)

456

(18)

110

(4 3/8)

KD-55X8500E

1,232

(48 5/8)

717

(28 1/4)

187

(7 3/8)

527

(20 3/4)

322

(12 3/4)

674

(26 5/8)

507

(20)

623

(24 5/8)

403

(15 7/8)

123

(4 7/8)

XBR-55X800E

1,232

(48 5/8)

716

(28 1/4)

147

(5 7/8)

488

(19 1/4)

330

(13)

675

(26 5/8)

467

(18 1/2)

623

(24 5/8)

406

(16)

117

(4 5/8)

XBR-49X800E

KD-49X8000E

1,096

(43 1/4)

640

(25 1/4)

151

(6)

456

(18)

315

(12 1/2)

603

(23 3/4)

434

(17 1/8)

557

(22)

369

(14 5/8)

117

(4 5/8)

Screen center point

19 (GB)

C: Portrait, no leaning

D: Portrait, +20° leaning

Unit: mm (inches)

Some models may not be available in certain regions.

Figures in the above table may differ slightly depending on the installation.

WARNING

The wall that the TV will be installed on should be capable of supporting a weight of at least four times that of

the TV.

Refer to your TV’s instructions for its weight.

Model Name

Display dimensions Screen center dimensions

Length for each mounting angle

Angle (0º) Angle (20º)



XBR-75X900E

KD-75X9000E

959

(37 7/8)

1,674

(66)

171

(6 3/4)

130

(5 1/8)

354

(14)

1,008

(39 3/4)

136

(5 3/8)

——

XBR-65X900E

KD-65X9000E

830

(32 3/4)

1,447

(57)

121

(4 7/8)

69

(2 3/4)

351

(13 7/8)

845

(33 3/8)

130

(5 1/8)

——

XBR-55X900E

KD-55X9000E

707

(27 7/8)

1,228

(48 3/8)

121

(4 7/8)

7

(9/32)

351

(13 7/8)

735

(29)

130

(5 1/8)

——

XBR-49X900E

KD-49X9000E

631

(24 7/8)

1,093

(43 1/8)

271

(10 3/4)

102

(4 1/8)

218

(8 5/8)

818

(32 1/4)

132

(5 1/4)

——

XBR-65X850E

KD-65X8500E

840

(33 1/8)

1,454

(57 1/4)

121

(4 7/8)

145

(5 3/4)

281

(11 1/8)

848

(33 1/2)

110

(4 3/8)

518

(20 1/2)

1,369

(54)

KD-55X8500E

717

(28 1/4)

1,232

(48 5/8)

171

(6 3/4)

30

(1 3/16)

336

(1

3 1/4)

787

(31)

123

(4 7/8)

451

(17 7/8)

1,162

(45 3/4)

XBR-55X800E

716

(28 1/4)

1,232

(48 5/8)

221

(8 3/4)

70

(2 7/8)

295

(11 5/8)

837

(33)

127

(5)

448

(17 3/4)

1,162

(45 3/4)

XBR-49X800E

KD-49X8000E

640

(25 1/4)

1,096

(43 1/4)

171

(6 3/4)

166

(6 5/8)

161

(6 3/8)

719

(28 3/8)

127

(5)

409

(16 1/8)

1,034

(40 3/4)

XBR-43X800E

KD-43X8000E

565

(22 1/4)

964

(38)

221

(8 3/4)

129

(5 1/8)

161

(6 3/8)

703

(27 3/4)

127

(5)

367

(14 1/2)

909

(35 7/8)

Screen center point

20 (GB)

Screw and Hook locations diagram/table

Model Name

A: Landscape, -20° leaning B: Landscape, +60° leaning C: Portrait, no leaning D: Portrait, +20° leaning

Screw

location

Hook

location

Screw

location

Hook

location

Screw

location

Hook

location

Screw

location

Hook

location

XBR-75X900E

KD-75X9000E

d, j a — — d, j a — —

XBR-65X900E

KD-65X9000E

d, g b — — d, g b — —

XBR-55X900E

KD-55X9000E

d, g b — — d, g b — —

XBR-49X900E

KD-49X9000E

f, j c — — f, j c — —

XBR-75X850E

KD-75X8500E

d, gae, ja————

XBR-65X850E

KD-65X8500E

e, j b d, g b d, g b d, g b

KD-55X8500E e, g c e, g c e, g c e, g c

XBR-55X800E e, g b e, g b e, j c e, j c

XBR-49X800E

KD-49X8000E

f, j c f, j c e, g c e, g c

XBR-43X800E

KD-43X8000E

————f, gcf, gc

Screw location

When installing the Mounting Hook on the TV.

Hook location

When installing the TV onto the Base Bracket.

c

a

b

La page charge ...

Sony XBR-55X800E Le manuel du propriétaire

Sony XBR-55X800E Le manuel du propriétaire

dans d''autres langues

Documents connexes