KitchenAid KFBU271TSS00 Le manuel du propriétaire

Marque: KitchenAid

Modèle: KFBU271TSS00

Catégorie: Barbecues

Taper: Le manuel du propriétaire

Ce manuel convient également à

®itchen_kid ®

OUTDOOR BUILT-IN DUAL SIDE BURNERS

For questions about features, operation/performance, parts, accessories or service, call: 1-800-422-1230

or visit our website at www.kitchenaid.com

In Canada, call for assistance, installation and service, call: 1-800-807-6777

or visit our website at www, Kitchenaid,ca

DEUX BRULEURS LATERAUX ENCASTRES

POUR USAGE EXTERIEUR

Au Canada, pour assistance, installation ou service composez le 1-800-807-6777 ou visitez notre site Web a...

www.Kitchenaid.ca

Table of Contents/Table des matieres ............................................................................. 2

iMPORTANT:

Save for local electrical inspector's use.

Installer: Leave installation instructions with the homeowner.

Homeowner: Keep installation instructions for future reference.

iMPORTANT :

_, conserver pour consultation par I'inspecteur local des installations _lectriques.

InstaHateur : Remettre les instructions d'installation au propri_taire.

Propri6taire : Conserver les instructions d'installation pour r_f_rence ult_rieure.

Models/Modeles KBZU122T KBZU242T

W10110732C

TABLEOF CONTENTS

OUTDOOR BUILT-IN SIDE BURNER SAFETY ............................ 3

INSTALLATION REQUIREMENTS ................................................ 5

Tools and Parts ............................................................................ 5

Location Requirements ................................................................ 5

Product Dimensions ..................................................................... 5

Cabinet Cutout Dimensions ......................................................... 6

Electrical Requirements ............................................................... 9

Gas Supply Requirements ........................................................... 9

INSTALLATION INSTRUCTIONS ................................................ 11

Outdoor Side Burner Installation ............................................... 11

Check and Adjust the Burners ................................................... 12

USING YOUR OUTDOOR SIDE BURNER .................................. 13

Lighting the Side Burner ............................................................ 13

OUTDOOR SIDE BURNER CARE ............................................... 14

General Cleaning ........................................................................ 14

TROUBLESHOOTING .................................................................. 15

ASSISTANCE OR SERVICE ......................................................... 15

In the U.S.A................................................................................ 15

Accessories ................................................................................ 15

In Canada ................................................................................... 15

WARRANTY .................................................................................. 16

TABLEDES MATIERES

SI_CURITI_ DU BRULEUR LATI_RAL

ENCASTRI_ D'EXTI_RIEUR .......................................................... 18

EXIGENCES D'INSTALLATION ................................................... 20

Outillage et pieces ...................................................................... 20

Exigences d'emplacement ......................................................... 20

Dimensions du produit ............................................................... 20

Dimensions de I'ouverture & decouper dans le placard ............ 21

Specifications electriques .......................................................... 24

Specifications de I'alimentation en gaz ..................................... 24

INSTRUCTIONS D'INSTALLATION ............................................. 26

Installation du brQleurs lateraux d'exterieur ............................... 26

Contr61e et reglage des brQleurs................................................ 27

UTILISATION DU BRULEUR LATERAL D'EXTERIEUR ............ 28

Allumage du brQleur lateral........................................................ 28

ENTRETIEN DU BRULEUR LATERAL D'EXTERIEUR .............. 29

Nettoyage gen6ral ...................................................................... 29

DEPANNAGE ................................................................................. 30

ASSISTANCE OU SERVICE ......................................................... 30

Accessoires ................................................................................ 30

GARANTIE ..................................................................................... 31

OUTDOOR BUILT-IN SIDE BURNER SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be killed or seriously injured if you don't immediately

follow instructions.

You can be killed or seriously injured if you don't follow

instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

_, DANGER

If you smell gas:

1. Shut off gas to the appliance.

2. Extinguish any open flame.

3. Open lid.

4. If odor continues, keep away from the

appliance and immediately call your

gas supplier or your fire department.

WARNING

1. Do not store or use gasoline or other

flammable liquids or vapors in the

vicinity of this or any other appliance.

2. An LP cylinder not connected for use

shall not be stored in the vicinity of

this or any other appliance.

State of California Proposition 65 Warnings:

WARNING: This product contains a chemical known to the State of California to cause cancer.

WARNING: This product contains a chemical known to the State of California to cause birth defects or other reproductive harm.

In the State of Massachusetts, the following installation instructions apply:

m Installations and repairs must be performed by a qualified or licensed contractor, plumber, or gasfitter qualified or licensed by

the State of Massachusetts.

m If using a ball valve, it shall be a T-handle type.

m A flexible gas connector, when used, must not exceed 3 feet.

IMPORTANT: This side burner is manufactured for outdoor use only. For side burners that are to be used at elevations above

2000 ft (609.6 m) orifice conversion is required. See "Gas Supply Requirements" section. It is the responsibility of the installer to comply

with the minimum installation clearances specified on the model/serial rating plate. The model/serial rating plate can be found on the

right-hand side panel.

Copies of the standards listed may be obtained from:

National Fire Protection Association CSA International

One Batterymarch Park 8501 East Pleasant Valley Rd.

Quincy, Massachusetts 02269 Cleveland, Ohio 44131-5575

iMPORTANT SAFETY iNSTRUCTiONS

WARNING: To reduce the risk of fire, electrical shock,

injury to persons, or damage when using the outdoor cooking

gas appliance, follow basic precautions, including the

following:

m Do not install portable or built-in outdoor cooking gas

appliances in or on a recreational vehicle, portable trailer,

boat or in any other moving installation.

m Always maintain minimum clearances from combustible

construction, see "Location Requirements" section.

m The outdoor cooking gas appliance shall not be located

under overhead unprotected combustible construction.

m This outdoor cooking gas appliance shall be used only

outdoors and shall not be used in a building, garage, or any

other enclosed area.

m Keep any electrical supply cord and fuel supply hose away

from any heated surfaces.

m Keep outdoor cooking gas appliance area clear and free

from combustible materials, gasoline and other flammable

vapors and liquids.

[] Do not obstruct the flow of combustion and ventilation air.

Keep the ventilation openings of the cylinder enclosure free

and clear from debris.

[] Inspect the gas cylinder supply hose before each use of the

outdoor cooking gas appliance. If the hose shows

excessive abrasion or wear, or is cut, it MUST be replaced

before using the outdoor cooking gas appliance. Contact

your dealer and use only replacement hoses specified for

use with the outdoor cooking gas appliance.

[] Visually check the burner flames. They should be blue.

Slight yellow tipping is normal for LP gas.

[] Check and clean burner/venturi tube for insects and insect

nest. A clogged tube can lead to fire under the outdoor

cooking gas appliance.

SAVE THESE

[] The LP gas supply cylinder to be used must be:

- constructed and marked in accordance with the

Specification for LP Gas Cylinders of the U.S. Department

of Transportation (DOT) or the National Standard of

Canada, CAN/CSA-B339, Cylinders, Spheres, and Tubes

for Transportation of Dangerous Goods; and Commission.

- provided with a listed overfilling prevention device.

- provided with a cylinder connection device compatible

with the connection for outdoor cooking gas appliances.

[] Always check connections for leaks each time you connect

and disconnect the LP gas supply cylinder. See

"Installation Instructions" section.

[] When the outdoor cooking gas appliance is not in use, the

gas must be turned off at the supply cylinder.

[] Storage of an outdoor cooking gas appliance indoors is

permissible only if the cylinder is disconnected and

removed from the outdoor cooking gas appliance.

[] Cylinders must be stored outdoors and out of the reach of

children and must not be stored in a building, garage, or

any other enclosed area.

[] The pressure regulator and hose assembly supplied with

the outdoor cooking gas appliance must be used. A

replacement pressure regulator and hose assembly

specific to your model is available from your outdoor

cooking gas appliance dealer.

[] Gas cylinder must include a collar to protect the cylinder

valve.

[] For appliances designed to use a CGA791 Connection:

Place a dust cap on cylinder valve outlet whenever the

cylinder is not in use. Only install the type of dust cap on

the cylinder valve outlet that is provided with the cylinder

valve. Other types of caps or plugs may result in leakage

of propane.

If the following information is not followed exactly, a fire

causing death or serious injury may occur.

[] Do not store a spare LP gas cylinder under or near this

outdoor cooking gas appliance.

[] Never fill the cylinder beyond 80 percent full.

iNSTRUCTiONS

INSTALLATION REQUIREMENTS

_?' i_: _ _._1:_

Gather the required tools and parts before starting installation.

Read and follow the instructions provided with any tools listed

here.

Tools Needed

• Tape measure

• Small, flat-blade screwdriver

• Flat-blade screwdriver

• #2 and #3 Phillips screwdriver

• Level

• Wrench or pliers

• Pipe wrench

• Scissors or cutting pliers (to remove tiedowns)

• Noncorrosive leak detection solution

Parts Needed

• Gas line shutoff valve

1/2"male pipe thread nipple for connection to pressure

regulator

LP gas-resistant pipe-joint compound

CSA design-certified outdoor flexible stainless steel

appliance connector (4-5 ft [1.2-1.5 m]) or rigid gas supply

line as needed.

Parts Supplied

• Convertible regulator set for 4" WCP Natural gas.

• Single-prong plug/5,000 mAmp transformer assembly

Select a location that provides minimum exposure to wind and

traffic paths. The location should be away from strong draft

areas.

Do not obstruct flow of combustion and ventilation air.

Clearance to combustible construction for built-in outdoor side

burners:

• A minimum of 24" (58 cm) must be maintained between the

sides and back and any combustible construction.

• A 24" (58 cm) minimum clearance must also be maintained

below the cooking surface and any combustible construction.

Ignition

A grounded, 3 prong outlet located to the left of the side burner is

required. See "Electrical Requirements" section.

Style I - Front to Back Built-In Dual Side Burners

-- A q

A. 13" (33 cm)

B. 10%" (27 cm)

C. 17" (43.2 cm)

D. 26%" (67 cm)

E.25_/_"(64.5 cm)

F.Manifold pipe

G.4%" (11.1 cm)

H.22%" (57.8 cm)

Style 2 - Side bySide Built-In Dual Side Burners

'_ A t

f--" ¢

E-_

/,P

A.24" (61cm)

B. 10%"(27cm)

C.28" (71.1cm)

D.201/_"(52.1 cm)

E. 191/_"(49.5 cm)

F.Manifold pipe

G.4%" (11.1 cm)

H. 17" (43.2 cm)

Built-In Outdoor Side Burner Enclosure

The enclosure for the built-in outdoor side burner is to be a minimum of 11" (28.0 cm) high x 23" (58.4 cm) deep x

14" (35.6 cm) wide for front to back model and 11" (28.0 cm) high x 17" (43.2 cm) deep x 25" (63.5 cm) wide for side by side model.

Counter or support surfaces must be level.

The installation of this grill must conform with local codes or, in the absence of local codes, with either the National Fuel Gas Code,

ANSI Z223.1/NPFA 54, Natural Gas and Propane Installation Code, CSA B149.1, or Propane Storage and Handling Code, B149.2.

Copies of the standards listed may be obtained from:

CSA International

8501 East Pleasant Valley Rd.

Cleveland, Ohio 44131-5575

NOTE: The outdoor side burner drops into the enclosure opening and is supported by its side flanges. No bottom support is needed.

The dimension chart and illustration below include cutout dimensions and minimum spacing requirements for all built-in outdoor

products. The illustration is for reference. The design of your cabinet layout can be personalized, but the dimensions for the cutouts and

minimum spacing must be followed.

E Gri!lsOhrrnentC

H A

Minimum Spacing Requirement Between Cutouts - Dimension K

Between 2 or more sets of Access Doors adjacent to each other:

K = 14" (35.6 cm) when 2 adjacent doors are opened to 90 degrees

K = 8" (20.3 cm) when 1 of the adjacent doors is opened to 90 degrees

Between a set of Access Doors and a Trash Drawer, Utility Drawer, Warming Drawer, Refrigerator, or Ice Maker:

K = 8" (20.3 cm) when 1 of the adjacent doors is opened to 90 degrees

Between a Trash Drawer, Utility Drawer, or Warming Drawer:

K = 3" (7.6 cm)

Cabinet Height and Depth Dimensions

Dimension A Minimum Dimension B Minimum

With outdoor refrigerator 37" (94.0 cm) 26" (66.0 cm)

Grill with insulated jacket 361/2'' (92.7 cm) 27" (68.6 cm)

Grill without insulated jacket 351/2'' (90.2 cm) 26" (66.0 cm)

Cutout Dimensions - Built-in Grill

Grill Size Dimension C Dimension D Dimension E

27" (68.6 cm) 29%" (75.2 cm) 10%" (27.3 cm) 227/8"(58.1 cm)

36" (91.4 cm) 388/8'' (98.1 cm) 10%" (27.3 cm) 227/8'' (58.1 cm)

48" (121.9 cm) 50%" (128.6 cm) 103_'' (27.3 cm) 227/8'' (58.1 cm)

Cutout Dimensions - Built-in Grill with Insulated Jacket

Grill Size Dimension C Dimension D Dimension E

27" (68.6 cm) 33" (83.8 cm) 11%" (29.8 cm) 24" (61.0 cm)

36" (91.4 cm) 42" (106.7 cm) 11%" (29.8 cm) 24" (61.0 cm)

48" (121.9 cm) 54" (137.2 cm) 113_'' (29.8 cm) 24" (61.0 cm)

Burner Position Dimension C Dimension D Dimension E

Front to Back 131/2'' (34.3 cm) 10%" (27.3 cm) 228/8'' (57.5 cm)

Side by Side 241/2'' (62.2 cm) 103_'' (27.3 cm) 167/8'' (42.9 cm)

Cutout Dimensions - Built-in Sear Burner

Dimension C Dimension D Dimension E

131/2'' (34.3 cm) 10%" (27.0 cm) 221Vie'' (57.6 cm)

Cutout Dimensions - Built-in Refreshment Center

Dimension C Dimension D Dimension E

301/2'' (77.5 cm) 10%" (27.3 cm) 23" (58.4 cm)

Cutout Dimensions - Built-in Access Doors

Door Size Dimension F Dimension L*

18" (45.7 cm) 163/16"(41.1 cm) 11/2"(3.8 cm)

27" (68.6 cm) 251/8'' (63.8 cm) 11/2"(3.8 cm)

30" (76.2 cm) 281/8'' (71.4 cm) 11/2"(3.8 cm)

36" (91.4 cm) 341/8'' (86.7 cm) 11/2"(3.8 cm)

48" (121.9 cm) 461/8'' (117.2 cm) 11/2'' (3.8 cm)

*Dimension L is the minimum mounting surface area around the opening for mounting the optional door or drawers.

Dimension G Dimension H

24" (61.0 cm) 35W' (89.5 cm)

Cutout Dimensions - Outdoor Ice Maker

Dimension G Dimension H

18" (45.7 cm) 34" (86.4 cm) min. to 341/2'' (87.6 cm) max.

Cutout Dimensions - Built-in Warming Drawer

Warming Drawer Size Dimension J

24" (61.0 cm) 221/2'' (57.2 cm)

Dimension M Dimension L*

12W' (31.1 cm) 11/2'' (3.8 cm)

*Dimension L is the minimum mounting surface area around the opening for mounting the optional door or drawers.

Built-in Outdoor Grill Enclosure Ventilation for LP Gas:

An enclosure for an LP gas fuel tank is to be ventilated by

openings at both the top and lower levels of the enclosure.

If converting to LP gas these vents are to be in the enclosure:

An enclosure for use with an LP gas fuel tank for built-in

installation is to have at least one ventilation opening on an

exposed exterior side located within 5" (12.7 cm) of the top is to

be a minimum of 20 in.2(129.0 cm2). One ventilation opening

within 1" (2.5 cm) of the bottom of the enclosure and the bottom

opening is to be a minimum of 10 in.2(64.5 cm_).All vent

openings are to be unobstructed. Every opening is to be a

minimum of 1/8"(0.32 cm) wide.

20 in.2(129.0 crn 2) rain.

ventimation both sides

1" (2.5 crn)

10 in? (64.5 crn 2)

ventilation both sides

5" (12.7 crn) max.

"_' (12.7 crn) max.

£:i',l@CI (;.a/_,.@;]!

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

If codes permit and a separate ground wire is used, it is

recommended that a qualified electrician determine that the

ground path is adequate.

Check with a qualified electrician if you are not sure whether the

side burner is properly grounded.

A 120-volt, 60-Hz, AC-only, 15-amp, fused electrical supply is

required.

It is recommended that aseparate circuit servicing only this side

burner be provided.

The model/serial number rating plate is located on the right-hand

side panel. See the following illustration.

A. Model/serial number plate

Recommended Ground Method

The outdoor side burner, when installed, must be electrically

grounded in accordance with local codes or, in the absence of

local codes, with the National Electrical Code ANSl/NFPA 70, or

Canadian Electrical Code, CSA C22.1.

Copies of the standards listed above may be obtained from:

CSA International

8501 East Pleasant Valley Rd.

Cleveland, Ohio 44131-5575

National Fire Protection Association

One Batterymarch Park

Quincy, Massachusetts 02269

g ............................

A. 3 prong ground plug

B. 3-prong polarized type outdoor GFI outlet

C. Ground prong

"" _f ; _'_'_ /s /s ,/ _ ..................

Explosion Hazard

Use a new CSA International approved "outdoor"

gas supply line.

Securely tighten all gas connections.

if connected to LP, have a qualified person make sure

gas pressure does not exceed 11" (28 cm) water

column.

Examples of a qualified person include:

licensed heating personnel,

authorized gas company personnel, and

authorized service personnel.

Failure to do so can result in death, explosion, or fire.

Observe all governing codes and ordinances.

IMPORTANT: This installation must conform with all local codes

and ordinances. In the absence of local codes, installation must

conform with American National Standard, National Fuel Gas

Code ANSI Z223.1 - latest edition or CAN/CGA B149.1 - latest

edition.

IMPORTANT: The side burner must be connected to a regulated

gas supply.

Refer to the model/serial rating plate for information on the type

of gas that can be used. If this information does not agree with

the type of gas available, check with your local gas supplier.

Gas Conversion:

No attempt shall be made to convert the side burner from the gas

specified on the model/serial rating plate for use with a different

gas type without consulting the serving gas supplier. The

conversion kits specified must be used.

Gas Pressure Regulator

The gas pressure regulator supplied with this side burner must be

used. The inlet (supply) pressure to the regulator should be as

follows for proper operation:

LP Gas:

Set pressure: 11" (27.9 cm) WCP

Inlet (supply) pressure: 11" to 14" (27.9 cm to 35.5 cm) WCP

Natural Gas:

Set pressure: 4" (10.2 cm) WCP

Inlet (supply) pressure: 7' to 14" (17.8 cm to 35.5 cm)

WCP maximum.

Contact local gas supplier if you are not sure about the inlet

(supply) pressure.

Burner Requirements for High Altitude

Input ratings shown on the model/serial rating plate are for

elevations up to 2,000 ft (609.6 m).

For elevations above 2,000 ft (609.6 m), ratings are reduced at a

rate of 4% for each 1,000 ft (304.8 m) above sea level. Orifice

conversion is required. See "Assistance or Service" section to

order.

Gas Supply Line Pressure Testing

Testing above 1/2psi (3.5 kPa) or 14" (35.5 cm) WCP (gauge):

The side burner and its individual shutoff valve must be

disconnected from the gas supply piping system during any

pressure testing of that system at test pressures greater than

1/2psig (3.5 kPa).

Testing below 1/2psi (3.5 kPa) or 14" (35.5 cm) WOP (gauge) or

lower:

The side burner must be isolated from the gas supply piping

system by closing its individual manual shutoff valve during any

pressure testing of the gas supply piping system at test

pressures equal to or less than 1/2psig (3.5 kPa).

Natural Gas

Side burners are equipped for use with Natural gas. They are

design-certified by CSA International for LP (propane or butane)

gases with appropriate conversion.

Side burners are set for natural gas use and have a pressure

regulator with 1/2'(1.3 cm) female pipe threads.

A ....................................

A. Rear side of burner

B.1/2"(1.3 cm)side burner gas pipe

C. New CSA approved outdoor flexible gas supply fine

The supply line shall be equipped with an approved shutoff valve.

This valve should be located in the same area as the burner and

should be in a location that allows ease of opening and closing.

Do not block access to the shutoff valve. The valve is for turning

on or shutting off gas to the appliance.

A. Gas supply line

B. Open position of shutoff valve

C. To side burner

LP gas conversion from a local LP gas supply:

Conversion must be made by a qualified person. A qualified

natural gas technician shall provide the LP gas supply to the

selected side burner location in accordance with the National

Fuel Gas Code ANSI Z2223.1/NFPA54 latest edition, and local

codes.

To convert to LP gas, the LP Gas Conversion Kit Number

W10118099 must be used. Follow Instructions included with kit.

LP gas conversion using a 20 Ib LP fuel tank:

To convert to LP gas, the LP Gas Conversion Kit Number

W10118099 must be used. Follow Instructions included with kit.

A 20 Ib (9.1 kg) LP gas fuel tank must be purchased separately.

INSTALLATION INSTRUCTIONS

(_:_td e_ __d_ _:__:_:_se:_ _:_:_st:a_la_:_o_

Excessive Weight Hazard

Use two or more people to move and install side

burner.

Failure to do so can result in back or other injury.

• Unpack side burner. Remove all packaging materials and

remove side burner from carton.

• Move side burner close to desired outdoor location.

Make Gas Connection

Natural Gas Use

This installation must conform with local codes and ordinances.

In the absence of local codes, installations must conform with

either the National Fuel Gas Code ANSI Z223.1 - latest edition, or

CAN/CGA-B149.1 Natural Gas and Propane installation code.

1. Place side burner into outdoor enclosure, but leave enough

room in back to connect to gas supply and plug in electrical

single-prong plug to the side burner.

Explosion Hazard

Use a new CSA International approved "outdoor"

gas supply line.

Securely tighten all gas connections.

Failure to do so can result in death, explosion, or fire.

Using a wrench to tighten, connect the gas supply to the side

burner. Use pipe-joint compound on all non-flared male

threads. Do not kink or damage the flexible connector when

moving the side burner.

............................D

A. 7/2"side burner gas pipe

B. New CSA International approved

"outdoor" flexible gas supply fine

C. Rear of side burner

D. To Natural gas supply

Open the manual shutoff valve in the gas supply line. The

valve is open when the handle is parallel to the gas pipe.

A. Closed valve

B. Open valve

Test all connections by brushing on an approved

noncorrosive leak-detection solution. Bubbles will show a

leak. Correct any leak found.

A combination of pipe fittings must be used to connect the

side burner to the existing gas line. If local codes permit, use

an outdoor flexible stainless steel tubing gas connector,

design-certified by CSA International, to connect the side

burner to the rigid gas supply line. A 5/8"diameter line is

recommended.

Pipe-joint compounds suitable for use with Natural gas must

be used. Do not use TEFLON ®ttape.

t®TEFLON is a registered trademark of E.I. Du Pont De Nemours and Company.

Plug in Side Burner

This built-in outdoor side burner comes with 5,000 mAmp

power transformer plug assembly for the igniter system. Plug

in the single-prong plug in the receptacle on the lower left-

hand side of the side burner.

A.Single-prong plug

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

The burners are tested and factory-set for most efficient

operation. However, variations in gas supply and other conditions

may make minor adjustments to low flame setting necessary. It is

recommended that adjustments be made by a qualified person.

Checking and adjusting the burner flames requires removing the

grate.

Low flame adjustment:

If flame goes out on the LO setting, the low flame setting must be

adjusted.

1. Light the burner and turn control knob to its lowest setting

and remove knob.

2. Hold the valve stem with pliers and insert a thin flat blade

screwdriver into the shaft.

3. Watch the flame and slowly turn screwdriver

counterclockwise.

4. Adjust flame to the minimum stable flame.

A. Valve stem

B. Flat-blade screwdriver

C. Pliers

5. Replace control knob and turn off the burner.

6. Reassemble grate.

2. Plug into a grounded 3 prong outlet.

3. Gently slide side burner completely into outdoor enclosure.

Assemble Cooking Area

1. Lift off cover and grate and set aside.

A. Cover

B. Grate

2. Remove packing from around burners.

3. Reinstall grate.

USING YOUR OUTDOOR SIDE BURNER

LI_II_I_ _!_ _Q_ _:_i_i_i_i_ '

Burn Hazard

Do not let the burner flame extend beyond the edge of

the pan.

Doing so can result in burns.

5. You will see the igniter glow. When burner is lit, release the

knob. Turn knob to desired setting.

6. Repeat for each of the other burners as needed.

IMPORTANT: If burner does not light immediately, turn the

burner knob to OFF and wait 5 minutes before relighting.

Manually lighting the side burner

1. Remove the outdoor side burner cover.

2. Remove the manual lighting extension (see following

illustration) and attach a match to the split ring.

Food Poisoning Hazard

Do not let food sit for more than one hour before or

after cooking.

Doing so can result in food poisoning or sickness.

1. Remove the outdoor side burner cover.

2. Make sure control knobs are turned to OFE

3. Turn the gas supply on.

Natural gas or LP gas from a local supply

• Using gas supply source other than 20 Ib LP gas fuel tank:

Turn the shutoff valve to open position from the front of gas

supply line.

20 Ib LP gas fuel tank, if converted

See the "Gas Supply Requirements" section.

• Using a 20 Ib LP gas fuel tank:

Slowly open the tank valve.

NOTE: If flow limiting device activates, your grill may not

light. If your grill does light, the flames will be low and will not

heat properly. Turn tank valve and all control knobs off and

wait 30 seconds. After shutting off the tank, very slowly open

tank valve and wait 5 seconds before lighting.

4. Do not lean over the side burner. Push in and turn the control

knob to LITE/HI and hold in.

Strike the match to light it.

Guide the match to the burner you wish to light.

Do not lean over the side burner. Push in and turn the burner

knob to LITE/HI for the burner closest to the lit match. The

burner will light immediately. When burner is lit, turn knob to

desired setting.

6. Repeat for each of the other burners as needed.

7. Remove match and replace manual lighting extension inside

its holder.

IM PORTANT:

If burner does not light immediately, turn the burner knob to OFF

and wait 5 minutes before relighting.

If any burners do not light after attempting to manually light them,

contact the KitchenAid Customer eXperience Center. See the

"Assistance or Service" section.

OUTDOOR SIDE BURNER CARE

IMPORTANT: Before cleaning, make sure all controls are off and

the side burner is cool. Always follow label instructions on

cleaning products.

For routine cleaning, wash with soap and water using a soft cloth

or sponge. Rinse with clean water and dry at once with a soft,

lint-free cloth to avoid spots and streaks.

Do not use steel wool to clean the side burner, as it will scratch

the surface.

To avoid weather damage to finish, use stainless steel side

burner cover.

STAINLESS STEEL

IMPORTANT: To avoid damage to stainless steel surfaces, do not

use soap-filled scouring pads, abrasive cleaners, Cooktop

Polishing Creme, steel wool, gritty wash cloths or paper towels.

To avoid damage to the finish, cleaners should not contain

chlorine.

Food spills should be cleaned as soon as entire side burner is

cool. Spills may cause permanent discoloration.

Cleaning Method:

• Rub in direction of grain to avoid scratching or damaging the

surface.

KitchenAid ®Stainless Steel Cleaner and Polish Part Number

4396920 (not included) or KitchenAid ®Stainless Steel Wipes

Part Number 8212510 (not included):

See "Assistance or Service" section to order.

• Liquid detergent or all-purpose cleaner:

• Rinse with clean water and dry with soft, lint-free cloth.

• Vinegar to remove hard water spots.

• Glass cleaner to remove fingerprints.

EXTERIOR

The quality of this material resists most stains and pitting,

providing that the surface is kept clean, polished and covered.

• Apply stainless steel polish to all non-cooking areas before

first use. Reapply after each cleaning to avoid permanent

damage to surface.

• Cleaning should always be followed by rinsing with clean

warm water.

Wipe the surface completely dry with a soft cloth.

For tough spots or baked-on grease, use Kitchen and BBQ

Grill Degreaser Part Number 31617, a commercial degreaser

designed for stainless steel.

See "Assistance or Service" section to order.

INTERIOR

Discoloration of stainless steel on these parts is to be expected,

due to intense heat from the burners. Always rub in the direction

of the grain. Cleaning should always be followed by rinsing with

clean, warm water.

Cleaning Method:

• Liquid detergent or all-purpose cleaner.

• Rinse with clean water and dry completely with a soft, lint-

free cloth.

A heavy-duty scrub sponge can be used with mild cleaning

products.

For small, difficult-to-clean areas, use Kitchen and BBQ Grill

Degreaser Part Number 31617, a commercial degreaser

designed for stainless steel.

See "Assistance or Service" section to order.

SIDE BURNER CAPS AND GRATE

Cleaning Method:

• Clean with a brass bristle brush.

• Wash grate using mild detergent, warm water and degreaser.

• Rinse with clean water and dry with soft, lint-free cloth.

• KitchenAid ®Stainless Steel Cleaner and Polish Part Number

4396920 (not included) or KitchenAid ®Stainless Steel Wipes

Part Number 8212510 (not included):

See "Assistance or Service" section to order.

KNOBS AND FLANGE AREA AROUND KNOBS

IMPORTANT: To avoid damage to knobs or to flange area around

knobs, do not use steel wool, abrasive cleaners, or oven cleaner.

Do not soak knobs.

Cleaning Method:

• Mild detergent, a soft cloth and warm water.

• Rinse and dry.

CONTROL PANEL GRAPHICS

IMPORTANT: To avoid damage to control panel graphics, do not

use steel wool, abrasive cleaners or oven cleaner.

Do not spray cleaner directly onto panel.

Cleaning Method:

• Clean around the burner labels gently; scrubbing may remove

printing.

• Mild detergent, soft cloth and warm water.

• Rinse and dry.

TROUBLESHOOTING

Try the solutions suggested here first in order to avoid the

cost of an unnecessary service call.

Nothing will operate

• Is the main or regulator gas shutoff valve in the off

position?

See the Installation Instructions.

• Is the gas supply properly connected?

Contact a trained repair specialist or see Installation

Instructions.

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

Is the 5,000 mAmp power supply cord unplugged?

Plug into a grounded 3 prong outlet.

Has a household fuse blown, or has a circuit breaker

tripped?

Replace the fuse or reset the circuit breaker. If the problem

continues, call an electrician.

ASSISTANCE OR SERVICE

Before calling for assistance or service, please check

"Troubleshooting." It may save you the cost of a service call. If

you still need help, follow the instructions below.

When calling, please know the purchase date and the complete

model and serial number of your appliance. This information will

help us to better respond to your request.

If you need replacement parts

If you need to order replacement parts, we recommend that you

use only factory specified parts. These factory specified parts will

fit right and work right because they are made with the same

precision used to build every new KITCHENAID ® appliance.

To locate factory specified parts in your area, call us or your

nearest KitchenAid designated service center.

Call the KitchenAid Customer eXperience Center toll free:

1-800-422-1230.

Our consultants provide assistance with:

Features and specifications on our full line of appliances.

Installation information.

Use and maintenance procedures.

Accessory and repair parts sales.

Specialized customer assistance (Spanish speaking, hearing

impaired, limited vision, etc.).

Referrals to local dealers, repair parts distributors and service

companies. KitchenAid designated service technicians are

trained to fulfill the product warranty and provide after-

warranty service, anywhere in the United States.

To locate the KitchenAid designated service company in your

area, you can also look in your telephone directory Yellow

Pages.

For further assistance

If you need further assistance, you can write to KitchenAid with

any questions or concerns at:

KitchenAid Brand Home Appliances

Customer eXperience Center

553 Benson Road

Benton Harbor, MI 49022-2692

Please include a daytime phone number in your correspondence.

Kitchen and BBQ Grill Degreaser

Order Part Number 31617

KitchenAid ®Stainless Steel Cleaner and Polish

Order Part Number 4396920

KitchenAid ®Stainless Steel Wipes

Order Part Number 8212510

Call the KitchenAid Canada Customer eXperience Centre toll

free: 1-800-807-6777.

Our consultants provide assistance with:

• Features and specifications on our full line of appliances.

• Use and maintenance procedures.

• Accessory and repair parts sales.

• Referrals to local dealers, repair parts distributors and service

companies. KitchenAid Canada designated service

technicians are trained to fulfill the product warranty and

provide after-warranty service, anywhere in Canada.

For further assistance

If you need further assistance, you can write to KitchenAid

Canada with any questions or concerns at:

Customer eXperience Centre

KitchenAid Canada

1901 Minnesota Court

Mississauga, Ontario L5N 3A7

Please include a daytime phone number in your correspondence.

KITCHENAID ®OUTDOOR PRODUCT WARRANTY

LIMITED WARRANTY

For one year from the date of purchase, when this outdoor product is operated and maintained according to instructions attached to or

furnished with the product, KitchenAid brand of Whirlpool Corporation or Whirlpool Canada LP (hereafter "KitchenAid") will pay for

Factory Specified Parts and repair labor to correct defects in materials or workmanship. Service must be provided by a KitchenAid

designated service company. This limited warranty is valid only in the United States or Canada and applies only when the outdoor

product is used in the country in which it was purchased. Outside the 50 United States and Canada, this limited warranty does not

apply. Proof of original purchase date is required to obtain service under this limited warranty.

SECOND THROUGH FIFTH YEAR LIMITED WARRANTY ON PARTS ON GRILLS ONLY

In the second through fifth years from the date of purchase when this grill is operated and maintained according to instructions

attached to or furnished with the product, KitchenAid will pay for Factory Specified Parts to correct defects in materials or

workmanship.

LIFETIME LIMITED WARRANTY ON STAINLESS STEEL COMPONENTS ON GRILLS ONLY

For the life of the product, when this grill is operated and maintained according to instructions attached to or furnished with the product,

KitchenAid will pay for replacement of the stainless steel body housing due to defective materials or workmanship. For the life of the

product, when this grill is operated and maintained according to instructions attached to or furnished with the product, KitchenAid will

pay for replacement parts for the stainless steel grill burners.

ITEMS EXCLUDED FROM WARRANTY

This limited warranty does not cover:

1. Service calls to correct the installation of your outdoor product, to instruct you on how to use your outdoor product, to replace or

repair house fuses, or to correct house wiring or plumbing.

2. Cosmetic damage, including scratches, dents, chips or other damage to the finish of your outdoor product, unless such damage

results from defects in materials or workmanship and is reported to KitchenAid within 30 days from the date of purchase.

3. Repairs when your outdoor product is used for other than normal, single-family household use or when it is used in a manner that is

contrary to published user or operator instructions and/or installation instructions.

4. Damage resulting from accident, alteration, misuse, abuse, fire, flood, acts of God, improper installation, installation not in

accordance with electrical or plumbing codes, or use of consumables or cleaning products not approved by KitchenAid.

5. Conversion kit or service call for the conversion of your outdoor product from natural gas to L.R/propane or from L.R/propane to

natural gas.

6. Costs associated with the removal from your home of your outdoor product for repairs. This outdoor product is designed to be

repaired in the home and only in-home service is covered by this warranty.

7. Repairs to parts or systems resulting from unauthorized modifications made to the outdoor product.

8. Expenses for travel and transportation for product service if your outdoor product is located in a remote area where service by an

authorized KitchenAid servicer is not available.

9. The removal and reinstallation of your outdoor product if it is installed in an inaccessible location or is not installed in accordance

with published installation instructions.

10. Damage resulting from normal wear and tear of your outdoor product.

11. Outdoor products with original model/serial numbers that have been removed, altered or cannot be easily determined. This

warranty is void if the factory applied serial number has been altered or removed from your outdoor product.

The cost of repair or replacement under these excluded circumstances shall be borne by the customer.

DISCLAIMER OF IMPLIED WARRANTIES; LIMITATION OF REMEDIES

CUSTOMER'S SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED

HEREIN. IMPLIED WARRANTIES, INCLUDING WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE,

ARE LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW. KITCHENAID SHALL NOT BE LIABLE FOR

INCIDENTAL OR CONSEQUENTIAL DAMAGES. SOME STATES AND PROVINCES DO NOT ALLOW THE EXCLUSION OR LIMITATION

OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, OR LIMITATIONS ON THE DURATION OF IMPLIED WARRANTIES OF

MERCHANTABILITY OR FITNESS, SO THESE EXCLUSIONS OR LIMITATIONS MAY NOT APPLY TO YOU. THIS WARRANTY GIVES

YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE OR PROVINCE

TO PROVINCE.

If outside the 50 United States and Canada, contact your authorized KitchenAid dealer to determine if another warranty applies.

If you need service, first see the "Troubleshooting" section of the Use & Care Guide. After checking "Troubleshooting," you may find

additional help by checking the "Assistance or Service" section or by calling KitchenAid. In the U.S.A., call 1-800-422-1230. In Canada,

call 1-800-807-6777. 9/07

Keep this book and your sales slip together for future

reference. You must provide proof of purchase or installation

date for in-warranty service.

Write down the following information about your major appliance

to better help you obtain assistance or service if you ever need it.

You will need to know your complete model number and serial

number. You can find this information on the model and serial

number label located on the product.

Dealer name

Address

Phone number

Model number

Serial number

Purchase date

SI CURITI DU BRULEUR LATI RAL

p p

ENCASTRE D'EXTERIEUR

Votre securit6 et celle des autres est tres importante.

Nous donnons de nombreux messages de s6curit6 importants dans ce manuel et sur votre appareil m6nager. Assurez-vous de

toujours lire tous les messages de s6curit6 et de vous y conformer.

Voici le symbole d'alerte de s6curit&

Ce symbole d'alerte de s6curit6 vous signale les dangers potentiels de d6c6s et de blessures graves & vous

et & d'autres.

Tousles messages de s6curit6 suivront le symbole d'alerte de s6curit6 et le mot "DANGER" ou

"AVERTISSEMENT". Ces mots signifient •

Risque possible de d6ces ou de blessure grave si vous ne

suivez pas imm6diatement les instructions.

Risque possible de d6ces ou de blessure grave si vous

ne suivez pas les instructions.

Tous les messages de s6curit6 vous diront quel est le danger potentiel et vous disent comment r6duire le risque de blessure et

ce qui peut se produire en cas de non-respect des instructions.

_, DANGER

En cas de detection d'une odeur de gaz :

1. Fermer I'arrivee de gaz de I'appareil.

2. I_teindre toute flamme nue.

3. Ouvrir le couvercle.

4. Si I'odeur persiste, s'eloigner de

I'appareil et appeler immediatement le

fournisseur en gaz ou les pompiers.

,_AVERTISSEMENT

1. Ne pas remiser ou utiliser de I'essence

ou tout autre liquide ou vapeur

inflammable & proximite de cet

appareil ou de tout autre appareil.

2. Ne pas remiser une bouteille de gaz de

petrole liquefie non raccordee

proximite de cet appareil ou de tout

autre appareil.

Avertissements de la proposition 65 de I'¢:tat de Californie "

AVERTISSEMENT " Ce produit contient un produit chimique connu par I'¢:tat de Californie pour 6tre & I'origine de cancers.

AVERTISSEMENT " Ce produit contient un produit chimique connu par I'¢:tat de Californie pour 6tre a I'origine de malformations

et autres d6ficiences de naissance.

Dans 1'12tatdu Massachusetts, les instructions d'installation suivantes sont applicables :

m Les travaux d'installation et r6paration doivent 6tre ex6cut6s par un plombier ou tuyauteur qualifi6 ou licenci6, ou par le

personnel qualifi6 d'une entreprise licenci6e par 1'12tatdu Massachusetts.

m Si une vanne & boisseau sph6rique est utilis6e, elle doit comporter une manette "T".

m Si un conduit de raccordement flexible est utilis6, sa Iongueur ne doit pas d6passer 3 pi.

IMPORTANT :Ce brQleur lat6ral est congu pour un usage a I'ext6rieur uniquement. Pour les brQleurs lateraux destines & 6tre

utilises & des altitudes superieures & 2000 pi (609,6 m), il est necessaire de convertir le gicleur. Voir la section "Specifications de

I'alimentation en gaz". C'est a I'installateur qu'incombe la responsabilite de respecter les degagements de separation minimums,

specifi6s sur la plaque signaletique de I'appareil. La plaque signaletique se trouve sur le c6te droit du brQleur lateral.

On peut obtenir des exemplaires des normes mentionnees aux adresses suivantes :

National Fire Protection Association CSA International

One Batterymarch Park 8501 East Pleasant Valley Rd.

Quincy, Massachusetts 02269 Cleveland, Ohio 44131-5575

IMPORTANTES iNSTRUCTiONS DE SECURITE

AVERTISSEIViENT : Pour r6duire le risque

d'incendie, de choc 61ectrique, de blessures corporelles

ou de dommages Iors de I'utilisation de I'appareil de

cuisson & gaz d'ext6rieur, il convient d'observer certaines

pr6cautions fondamentales, notamment :

m Ne pas installer les appareils de cuisson & gaz

d'ext6rieur (portatifs ou encastr6s) dans ou sur un

v6hicule r6cr6atif, une remorque portative, un bateau

ou toute autre installation mobile.

m Toujours respecter les distances de s6paration

minimales entre I'appareil et les constructions

combustibles; voir la section "Exigences

d'emplacement".

m L'appareil de cuisson & gaz d'ext6rieur ne doit pas 6tre

situ6 sous une construction combustible non prot6g6e.

m Cet appareil de cuisson &gaz d'ext6rieur doit 6tre

utilis6 & I'ext6rieur uniquement; ne pas I'utiliser dans

un b&timent, un garage ou tout autre endroit clos.

m Conserver le cordon d'alimentation 61ectrique et le

tuyau d'alimentation en combustible & 1'6cart des

surfaces chauff6es.

m Maintenir la zone de I'appareil de cuisson & gaz

d'ext6rieur & I'abri des mat6riaux combustibles,

essence ou autres vapeurs ou liquides inflammables.

m Ne pas obstruer le flux de combustion et la ventilation.

Conserver les ouvertures de ventilation de I'enceinte

de la bouteille de gaz libre et d6pourvues de d6bris.

m Inspecter le tuyau d'alimentation de la bouteille de gaz

avant chaque utilisation de I'appareil de cuisson & gaz

d'ext6rieur. Si le tuyau pr6sente d'importants signes

d'abrasion ou d'usure ou s'il est coup6, il DOlT 6tre

remplac6 avant toute nouvelle utilisation de I'appareil

de cuisson & gaz d'ext6rieur. Contacter votre

marchand et utiliser uniquement les tuyaux de

rechange sp6cifi6s pour utilisation avec I'appareil de

cuisson & gaz d'ext6rieur.

m Inspecter visuellement les flammes du brt_leur. Elles

doivent 6tre bleues. Avec du gaz de p6trole liqu6fi6, il

est normal d'observer une 16g_re pointe jaune.

m Nettoyer le tube du brQleur/de la buse et v6rifier

I'absence d'insectes ou de nids d'insectes. Un tube

obstru6 peut entrafner un feu sous I'appareil de

cuisson & gaz d'ext6rieur.

CONSERVEZ

[] La bouteille d'alimentation au gaz de p6trole liqu6fi6 utilis6e doit

6tre :

- construite et marqu6e conform6ment aux sp6cifications pour

les bouteilles de gaz de p6trole liqu6fi6 du U.S. Department of

Transportation (DOT) ou de la Norme nationale du Canada,

CAN/CSA-B339, Bouteilles, tubes et autres r6cipients pour le

transport des marchandises dangereuses; et de la

Commission.

- fournie avec un dispositif de pr6vention de remplissage

excessif.

- fournie avec un dispositif de connexion de la bouteille de gaz

compatible avec la connexion pour les appareils de cuisson

gaz d'ext6rieur.

[] Toujours v6rifier les connexions pour identifier des fuites

chaque branchement et d6branchement de la bouteille

d'alimentation en gaz de p6trole liqu6fi& Voir la section

"Instructions d'installation".

[] Lorsque I'appareil de cuisson a gaz d'ext6rieur n'est pas utilis6,

I'arriv6e de gaz doit 6tre ferm6e au niveau de la bouteille de

gaz.

[] Le remisage d'un appareil de cuisson a gaz d'ext6rieur est

autoris6 seulement en cas de d6branchement et de retrait de la

bouteille de gaz de I'appareil.

[] Les bouteilles de gaz doivent 6tre remis6es a I'ext6rieur et hors

de port6e des enfants; elles ne doivent pas 6tre remis6es dans

un b&timent, un garage ou tout endroit clos.

[] II est n6cessaire d'utiliser le d6tendeur et le tuyau fournis avec

I'appareil de cuisson a gaz d'ext6rieur. Un d6tendeur et un

tuyau de rechange sp6cifiques a votre module sont disponibles

aupr_s de votre marchand d'appareils de cuisson a gaz

d'ext6rieur.

[] La bouteille de gaz doit comporter un manchon destin6

prot6ger le robinet de la bouteille.

[] Pour les appareils con£us pour utiliser une connexion CGA791:

Placer un capuchon protecteur sur le robinet de la bouteille de

gaz Iorsqu'elle n'est pas utilis6e. Installer uniquement le type de

capuchon protecteur sur le conduit d'6vacuation fourni avec la

bouteille de gaz. D'autres types de capuchons ou obturateurs

pourraient provoquer des fuites de propane.

Le non-respect des instructions suivantes peut entrafner un

incendie causant la mort ou des blessures graves.

[] Ne pas remiser une bouteille de gaz de p6trole liqu6fi6 de

secours sous I'appareil de cuisson a gaz d'ext6rieur ou

proximit6 de celui-ci.

[] Ne jamais remplir la bouteille au-dela de 80 % de sa capacit6

de remplissage.

CES iNSTRUCTiONS

EXIGENCES D'INSTALLATION

Rassembler les outils et pieces necessaires avant de commencer

I'installation. Lire et suivre les instructions fournies avec les outils

indiqu6s ici.

Outillage n_cessaire

• M_tre ruban

• Petit tournevis & lame plate

• Tournevis & lame plate

• Tournevis Phillips n° 2 et n° 3

• Niveau

• Cle ou pince

• Cle & tuyauterie

• Ciseaux ou pince coupante (pour couper les attaches)

• Solution non-corrosive de detection des fuites

Pi6ces n6cessaires

Robinet d'arr_t de gaz manuel

Raccord droit male filete, 1/2",pour raccordement au

detendeur

Compose d'etanch6it6 des tuyauteries resistant & I'action du

gaz propane

Conduit de raccordement flexible d'exterieur (Iongueur de 4 &

5 pi [1,2 &1,5 m], acier inoxydable, homologation CSA), ou

canalisation de gaz rigide, selon le cas.

Pi6ces fournies

• Detendeur convertible pour gaz naturel sous pression de 4"

(colonne d'eau)

• Ensemble transformateur de 5000 mA/prise &une broche

Selectionner un emplacement oQ I'exposition au vent est faible et

les passages peu nombreux. L'emplacement ne doit pas se

trouver dans une zone & forts courants d'air.

Ne pas obstruer le flux de combustion et de ventilation.

Distance de separation entre les constructions combustibles et

les brQleurs lateraux encastres d'exterieur :

• Un minimum de 24" (58 cm) doit _tre maintenu entre les c6tes

et I'arriere et toute construction combustible.

• Un degagement minimum de 24" (58 cm) doit egalement _tre

maintenu sous la surface de cuisson et toute construction

combustible.

Allumage

On doit disposer a proximite du c6t6 gauche du brQleur lateral

d'une prise de courant polarisee d'exterieur reliee a la terre, &

3 alveoles. Voir la section "Specifications electriques".

Style I - Deux br0leurs encastr_s, configuration avant/arri_re

® ©

A. 13"_3c_

B. 10%"_7c_

C. 17"_3,2c_

D. 26%"_7c_

E. 253/8''(64,5 cm)

F. Tuyau de distribution

G. 43/8"(11,1 cm)

H. 228/4"(5 7,8 cm)

Style 2 - Deux br0leurs encastr_s lat_raux

A.24" (61cm)

B. 10%" (27cm)

C.28" (71,1 cm)

D. 201/2" (52,1 cm)

E. 191/2'' (49,5 cm)

F. Tuyau de distribution

G. 4%" (11,1 cm)

H. 1F" (43,2 cm)

La page charge ...

KitchenAid KFBU271TSS00 Le manuel du propriétaire

Marque: KitchenAid

Modèle: KFBU271TSS00

Catégorie: Barbecues

Taper: Le manuel du propriétaire

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: KitchenAid KFBU271TSS00 Owner's manual

KitchenAid KFBU271TSS00 Le manuel du propriétaire

Ce manuel convient également à

KitchenAid KFBU271TSS00 Le manuel du propriétaire

dans d''autres langues

Documents connexes