Roland Micro Cube GX BK Le manuel du propriétaire

Owner’s Manual

Bedienungsanleitung

Mode d’emploi

Manuale dell'utente

Manual del usuario

Manual do proprietário

Gebruikershandleiding

NederlandsPortuguêsEspañolItalianoFrançaisDeutschEnglish

Owner’s Manual

Guitar Amplier

NederlandsPortuguêsEspañolItalianoFrançaisDeutschEnglish

Owner’s Manual

Guitar Amplier

Before using this unit, carefully read the sections entitled “USING THE UNIT SAFELY” (p. 2) and “IMPORTANT NOTES” (p. 5). These

sections provide important information concerning the proper operation of the unit. Additionally, in order to feel assured that you

have gained a good grasp of every feature of your new unit, read Owner’s Manual in its entirety. This manual should be saved and

kept on hand as a convenient reference.

CORPORATION.

i-CUBE LINK jack allows convenient practicing (p. 10)

• The i-CUBE LINK jack lets you carry out recording and playback using an iPad/iPhone app.

Two-way power supply lets you play anywhere (p. 8)

• The MICRO CUBE GX can be powered either by six AA batteries or by an AC adaptor.

• When operating on batteries (alkaline batteries), you can use the MICRO CUBE GX for approximately 20 hours

(This can vary depending on the capacity of the batteries and the conditions of use.).

• When operating on batteries (rechargeable Ni-MH batteries), you can use the MICRO CUBE GX for

approximately 25 hours (This can vary depending on the capacity of the batteries and the conditions of use.).

Seven types of COSM amps and eight types of eects are built in. Mic input is also supported (p. 6)

• Seven types of COSM amps are built in, giving you the sounds you need for a wide range of styles (included

amps: ACOUSTIC SIM, JC CLEAN, BLACK PANEL, BRIT COMBO, CLASSIC STACK, R-FIER STACK, EXTREME).

• Two built-in eects processors oer a selection of eight dierent eects (EFX: CHORUS, FLANGER, PHASER,

TREMOLO, HEAVY OCTAVE), (DELAY/REVERB: DELAY, REVERB, SPRING).

• Mic input is also accepted, allowing you to use the MICRO CUBE GX as a portable microphone amp.

COSM ( Composite Object Sound Modeling) is Roland’s innovative and powerful sound modeling technology. COSM

analyzes the many factors that make up the original sound, such as the electrical and physical characteristics of the original, and then

produces a digital model that can reproduce the same sound.

Memory function lets you store and call up settings (p. 9)

• Use the Memory function to store and call up settings for each amp type.

The MICRO CUBE GX is a high-performance guitar

amp with 3 W output and a 12 cm (5-inch) speaker.

2

USING THE UNIT SAFELY

WARNING

To completely turn o power to the unit, pull out the

AC adaptor from the outlet

Even with the power switch turned o, this unit is

not completely separated from its main source of

power. When the power needs to be completely

turned o, turn o the power switch on the unit,

then pull out the AC adaptor from the outlet. For

this reason, the outlet into which you choose to connect the

AC adaptor should be one that is within easy reach and readily

accessible.

Do not disassemble or modify by yourself

Do not open (or modify in any way) the unit or

its AC adaptor.

Do not repair or replace parts by yourself

Do not attempt to repair the unit, or replace

parts within it (except when this manual provides

specic instructions directing you to do so).

Refer all servicing to your retailer, the nearest

Roland Service Center, or an authorized Roland

distributor, as listed on the “Information” page.

Do not use or store in the following types of locations

• Subject to temperature extremes (e.g., direct

sunlight in an enclosed vehicle, near a heating

duct, on top of heat-generating equipment);

or are

• Damp (e.g., baths, washrooms, on wet oors);

or are

• Exposed to steam or smoke; or are

• Subject to salt exposure; or are

• Humid; or are

• Exposed to rain; or are

• Dusty or sandy; or are

• Subject to high levels of vibration and shakiness.

WARNING

Do not place in an unstable location

Make sure you always have the unit placed so it is

level and sure to remain stable. Never place it on

stands that could wobble, or on inclined surfaces

Use only the supplied AC adaptor and the correct

voltage

Be sure to use only the AC adaptor supplied with

the unit. Also, make sure the line voltage at the

installation matches the input voltage specied

on the AC adaptor’s body. Other AC adaptors

may use a dierent polarity, or be designed for

a dierent voltage, so their use could result in

damage, malfunction, or electric shock.

Do not bend the power cord or place heavy objects

on it

Do not excessively twist or bend the power

cord, nor place heavy objects on it. Doing so can

damage the cord, producing severed elements

and short circuits. Damaged cords are re and

shock hazards!

Avoid extended use at high volume

This unit, either alone or in combination with an

amplier and headphones or speakers, may be

capable of producing sound levels that could

cause permanent hearing loss. Do not operate for

a long period of time at a high volume level, or at

a level that is uncomfortable. If you experience

any hearing loss or ringing in the ears, you should immediately

stop using the unit, and consult an audiologist.

Used for instructions intended to alert the

user to the risk of injury or material

damage should the unit be used

improperly.

* Material damage refers to damage or

other adverse effects caused with

respect to the home and all its

furnishings, as well to domestic animals

or pets.

Used for instructions intended to alert the

user to the risk of death or severe injury

should the unit be used improperly.

The symbol alerts the user to things that must be

carried out. The specific thing that must be done is

indicated by the design contained within the circle. In the

case of the symbol at left, it means that the power-cord

plug must be unplugged from the outlet.

The symbol alerts the user to important instructions or

warnings. The specific meaning of the symbol is

determined by the design contained within the triangle. In

the case of the symbol at left, it is used for general

cautions, warnings, or alerts to danger.

The symbol alerts the user to items that must never be

carried out (are forbidden). The specific thing that must

not be done is indicated by the design contained within

the circle. In the case of the symbol at left, it means that

the unit must never be disassembled.

About WARNING and CAUTION Notices

About the Symbols

ALWAYS OBSERVE THE FOLLOWING

NederlandsPortuguêsEspañolItalianoFrançaisDeutschEnglish

USING THE UNIT SAFELY

3

WARNING

Don’t allow foreign objects or liquids to enter unit;

never place containers with liquid on unit

Do not place containers containing liquid (e.g.,

ower vases) on this product. Never allow

foreign objects (e.g., ammable objects, coins,

wires) or liquids (e.g., water or juice) to enter this

product. Doing so may cause short circuits, faulty

operation, or other malfunctions.

Turn o the unit if an abnormality or malfunction

occurs

Immediately turn the unit o, remove the AC

adaptor from the outlet, and request servicing by

your retailer, the nearest Roland Service Center,

or an authorized Roland distributor, as listed on

the “Information” page when:

• The AC adaptor or the power-supply cord has been damaged;

or

• If smoke or unusual odor occurs; or

• Objects have fallen into, or liquid has been spilled onto the

unit; or

• The unit has been exposed to rain (or otherwise has become

wet); or

• The unit does not appear to operate normally or exhibits a

marked change in performance.

Adults must provide supervision in places where

children are present

When using the unit in locations where children

are present, be careful so no mishandling of the

unit can take place. An adult should always be on

hand to provide supervision and guidance.

Do not drop or subject to strong impact

Protect the unit from strong impact.

(Do not drop it!)

Do not share an outlet with an unreasonable number

of other devices

Do not force the unit’s power-supply cord to

share an outlet with an unreasonable number of

other devices. Be especially careful when using

extension cords—the total power used by all

devices you have connected to the extension

cord’s outlet must never exceed the power rating

(watts/amperes) for the extension cord. Excessive loads can

cause the insulation on the cord to heat up and eventually melt

through.

Do not use overseas

Before using the unit in overseas, consult with

your retailer, the nearest Roland Service Center,

or an authorized Roland distributor, as listed on

the “Information” page.

WARNING

Handle batteries carefully

• Batteries must never be heated, taken apart, or

thrown into re or water.

• Never expose batteries to excessive heat such

as sunshine, re or the like.

• Incorrect handling of batteries can cause

leakage, overheating, re, or explosion. Before

use, you must read and strictly observe all of

the precautions that accompany the batteries,

rechargeable batteries, or battery charger.

• When using rechargeable batteries and

a charger, use only the combination of

rechargeable batteries and charger specied

by the battery manufacturer.

USING THE UNIT SAFELY

4

CAUTION

Place in a well ventilated location

The unit and the AC adaptor should be located so

their location or position does not interfere with

their proper ventilation.

When disconnecting an AC adaptor, grasp it by the

plug

To prevent conductor damage, always grasp

the AC adaptor by its body or its plug when

disconnecting it from this unit or from a power

outlet.

Periodically clean the AC adaptor’s plug

At regular intervals, you should unplug the AC

adaptor and clean it by using a dry cloth to wipe

all dust and other accumulations away from its

prongs. Also, disconnect the power plug from

the power outlet whenever the unit is to remain

unused for an extended period of time. Any

accumulation of dust between the power plug and the power

outlet can result in poor insulation and lead to re.

Manage cables for safety

Try to prevent cords and cables from becoming

entangled. Also, all cords and cables should be

placed so they are out of the reach of children.

Avoid climbing on top of the unit, or placing heavy

objects on it

Never climb on top of, nor place heavy objects

on the unit.

Do not connect or disconnect the AC adaptor with

wet hands

Never handle the AC adaptor body, or its output

plugs, with wet hands when plugging into, or

unplugging from, an outlet or this unit.

Disconnect everything before moving the unit

Before moving the unit, disconnect the AC

adaptor and all cords coming from external

devices.

Unplug the AC adaptor from the outlet before

cleaning

Before cleaning the unit, turn it o and unplug

the AC adaptor from the outlet.

CAUTION

If there is a possibility of lightning strike, disconnect

the AC adaptor from the outlet

Whenever you suspect the possibility of lightning

in your area, disconnect the AC adaptor from

the outlet.

Handle batteries carefully

If used improperly, batteries may explode or

leak and cause damage or injury. In the interest

of safety, please read and observe the following

precautions (p. 8).

• Carefully follow the installation instructions

for batteries, and make sure you observe the

correct polarity.

• Avoid using new batteries together with used

ones. In addition, avoid mixing dierent types

of batteries.

• Remove the batteries whenever the unit is to

remain unused for an extended period of time.

• Never keep batteries together with metallic

objects such as ballpoint pens, necklaces,

hairpins, etc.

• Used batteries must be disposed of in compliance with

whatever regulations for their safe disposal that may be

observed in the region in which you live.

Handle the ground terminal carefully

If you remove the screw from the ground

terminal, be sure to replace it; don’t leave it lying

around where it could accidently be swallowed

by small children. When refastening the screw,

make that it is rmly fastened, so it won’t come

loose.

Handle leaking batteries carefully

• If uid has leaked from a battery, make sure

not to touch it with your bare hands.

• If any of the leaking uid gets into your eyes,

the loss of vision may result. Do not rub your

eyes; use clean water to ush them thoroughly.

Then, promptly see a doctor.

• Burning of the skin or dermatitis may result if

uid has gotten onto your skin or clothing. Use

clean water to ush aected areas thoroughly;

then, promptly see a doctor.

• Using a soft cloth, carefully wipe any remaining uid from

the inside of the battery compartment. Then, install new

batteries.

NederlandsPortuguêsEspañolItalianoFrançaisDeutschEnglish

5

IMPORTANT NOTES

Power Supply

• Do not connect this unit to same

electrical outlet that is being used

by an electrical appliance that is

controlled by an inverter or a motor

(such as a refrigerator, washing machine,

microwave oven, or air conditioner).

Depending on the way in which the

electrical appliance is used, power

supply noise may cause this unit to

malfunction or may produce audible

noise. If it is not practical to use a

separate electrical outlet, connect a

power supply noise lter between this

unit and the electrical outlet.

• The AC adaptor will begin to generate

heat after long hours of consecutive

use. This is normal, and is not a cause

for concern.

• The use of an AC adaptor is

recommended as the unit’s power

consumption is relatively high. Should

you prefer to use batteries, please use

the alkaline, rechargeable Ni-MH type.

• To prevent malfunction and equipment

failure, always make sure to turn o the

power on all your equipment before you

make any connections.

• When installing or replacing batteries,

always turn this unit o and disconnect

any other devices you may have

connected. This way, you can prevent

malfunction and damage.

• If the batteries run extremely low, the

sound may distort or interruptions in the

sound may occur at high volume levels,

but this does not indicate a malfunction.

If this occurs, please replace the batteries

or use the included AC adaptor.

• If operating this unit on batteries, please

use alkaline batteries, rechargeable

Ni-MH batteries.

• If operating this unit on batteries, please

disconnect the AC adaptor from this unit.

Placement

• Using the unit near power ampliers

(or other equipment containing large

power transformers) may induce hum.

To alleviate the problem, change the

orientation of this unit; or move it farther

away from the source of interference.

• This device may interfere with radio and

television reception. Do not use this

device in the vicinity of such receivers.

• Noise may be produced if wireless

communications devices, such as cell

phones, are operated in the vicinity of

this unit. Such noise could occur when

receiving or initiating a call, or while

conversing. Should you experience

such problems, you should relocate

such wireless devices so they are at a

greater distance from this unit, or switch

them o.

• Do not expose the unit to direct sunlight,

place it near devices that radiate heat,

leave it inside an enclosed vehicle, or

otherwise subject it to temperature

extremes. Also, do not allow lighting

devices that normally are used while

their light source is very close to the

unit (such as a piano light), or powerful

spotlights to shine upon the same area

of the unit for extended periods of time.

Excessive heat can deform or discolor

the unit.

• When moved from one location to

another where the temperature and/or

humidity is very dierent, water droplets

(condensation) may form inside the unit.

Damage or malfunction may result if you

attempt to use the unit in this condition.

Therefore, before using the unit, you

must allow it to stand for several hours,

until the condensation has completely

evaporated.

• Do not allow rubber, vinyl, or similar

materials to remain on this unit for

long periods of time. Such objects can

discolor or otherwise harmfully aect

the nish.

• Do not paste stickers, decals, or the like

to this instrument. Peeling such matter

o the instrument may damage the

exterior nish.

• Depending on the material and

temperature of the surface on which

you place the unit, its rubber feet may

discolor or mar the surface.

You can place a piece of felt or cloth

under the rubber feet to prevent this

from happening. If you do so, please

make sure that the unit will not slip or

move accidentally.

• Do not place containers or anything

else containing liquid on top of this

unit. Also, whenever any liquid has been

spilled on the surface of this unit, be sure

to promptly wipe it away using a soft,

dry cloth.

Maintenance

• For everyday cleaning wipe the unit

with a soft, dry cloth or one that has

been slightly dampened with water.

To remove stubborn dirt, use a cloth

impregnated with a mild, non-abrasive

detergent. Afterwards, be sure to wipe

the unit thoroughly with a soft, dry cloth.

• Never use benzine, thinners, alcohol

or solvents of any kind, to avoid the

possibility of discoloration and/or

deformation.

Additional Precautions

• Use a reasonable amount of care when

using the unit’s buttons, sliders, or other

controls; and when using its jacks and

connectors. Rough handling can lead to

malfunctions.

• When disconnecting all cables, grasp

the connector itself—never pull on the

cable. This way you will avoid causing

shorts, or damage to the cable’s internal

elements.

• To avoid disturbing others nearby, try

to keep the unit’s volume at reasonable

levels.

• When you need to transport the

unit, package it in the box (including

padding) that it came in, if possible.

Otherwise, you will need to use

equivalent packaging materials.

• Some connection cables contain

resistors. Do not use cables that

incorporate resistors for connecting

to this unit. The use of such cables

can cause the sound level to be

extremely low, or impossible to hear.

For information on cable specications,

contact the manufacturer of the cable.

Intellectual Property Right

• It is forbidden by law to make an audio

recording, video recording, copy or

revision of a third party’s copyrighted

work (musical work, video work,

broadcast, live performance, or other

work), whether in whole or in part,

and distribute, sell, lease, perform, or

broadcast it without the permission of

the copyright owner.

• Do not use this product for purposes

that could infringe on a copyright

held by a third party. We assume no

responsibility whatsoever with regard

to any infringements of third-party

copyrights arising through your use of

this product.

• MMP (Moore Microprocessor Portfolio)

refers to a patent portfolio concerned

with microprocessor architecture, which

was developed by Technology Properties

Limited (TPL). Roland has licensed this

technology from the TPL Group.

• Roland, COSM, MICRO CUBE are either

registered trademarks or trademarks of

Roland Corporation in the United States

and/or other countries.

• Company names and product names

appearing in this document are

registered trademarks or trademarks of

their respective owners.

• The product names mentioned in

this document are trademarks or

registered trademarks of their respective

owners, and are not related to Roland

Corporation. In this manual, these names

are used because it is the most practical

way of describing the sounds that are

simulated using COSM technology.

• iPad, iPhone are either registered

trademarks or trademarks of Apple Inc.

6

Control Panel

2

1

iPhone, iPad, etc.

Microphone,

Electric Guitar

3 4 5 6

7 8 9 10

11

12

Panel Descriptions

1 INPUT jack

Connect your guitar or microphone here.

* Howling could be produced depending on the location of

microphones relative to speakers. This can be remedied

by:

1. Changing the orientation of the microphone(s).

2. Relocating microphone(s) at a greater distance from

speakers.

3. Lowering volume levels.

* To prevent malfunction and equipment failure, always turn

down the volume, and turn o all the units before making

any connections.

2 i-CUBE LINK/AUX IN jack

i-CUBE LINK

If you use the included mini cable (4-pole) to connect

your iPad/ iPhone, you’ll be able to use the i-CUBE LINK

function (p. 10).

AUX IN

Use the included mini cable (4-pole) or a commercially

available stereo-mini cable to connect your digital audio

player or iPad/iPhone here.

3 [MEMORY] button

Turns the unit’s memory feature on/o.

The memory feature lets you individually save your

settings for each of the eight amp types (p. 9).

Memory Explanation

ON (lit)

The MICRO CUBE GX will sound according to

the knob settings you previously stored.

OFF (unlit)

The MICRO CUBE GX will sound according to

the current knob settings.

4 [AMP TYPE] switch

You can select from the following eight amp types:

Type Explanation

ACOUSTIC

SIM

This original amplier model gives you a dynamic

acoustic guitar sound using a standard electric

guitar.

JC CLEAN

This is a model of Roland’s famous JC-120 Jazz

Chorus guitar amplier. The ultra-clean, ultra-at

sound oers a smooth tone. This becomes more

eective when used in combination with a external

eector.

BLACK

PANEL

This is modeled on the classic Fender Twin Reverb

amplier, used in a wide variety of musical styles,

from country to blues, jazz and rock. Exhibiting rich

lows and a bright high end.

BRIT

COMBO

This is modeled on the Vox AC-30TB, the rock

amplier that created the Liverpool sound of the

‘60s. It can produce a broad range of sounds, from

clean to overdrive, with increased distortion and

greater power in the low-midrange when the

amplier’s gain is boosted.

CLASSIC

STACK

This is modeled on the sound and response of a

Marshall JMP1987. This is a rock amp distinctive for

its fat, solid sound, and a smooth tone that extends

into the “presence” frequency range.

R-FIER

STACK

This is modeled on the MESA/Boogie Rectier.

This super high gain amp is capable of producing

slash metal, grunge, and a wide range of other

lead sounds.

EXTREME

This original high-gain amp delivers thick lows and

intense distortion while still preserving the sound’s

clear denition.

MIC

Select this position when a microphone is

connected.

* All product names mentioned in this document are trademarks

or registered trademarks of their respective owners, and are

not related to Roland Corporation. In this manual, these names

are used as appropriate ways to indicate sounds that are

simulated using COSM technology.

NederlandsPortuguêsEspañolItalianoFrançaisDeutschEnglish

Panel Descriptions

7

5 [EFX] knob

Turn this knob to select the eect. Turn the knob to adjust

the amount of eect applied.

* Graduations for each eect on a panel are for reference. Be

sure to check the sound as you adjust the eects.

Eect Explanation

CHORUS

In this eect, a slightly detuned sound is added

to the original sound, giving the sound greater

breadth and fullness.

FLANGER

This creates a anging eect that creates a sort of

spinning sensation with the sound.

PHASER

This eect adds a variable phase-shifted signal

to the direct sound, giving the sound a swirling

character.

TREMOLO

Tremolo is an eect that creates a cyclic change

in volume.

HEAVY

OCTAVE

This adds sound lowered by an octave to the

original sound. Since you can play chords even

when using this eect, you can use it to fatten the

sound of your chordal playing as well.

6 [DELAY/REVERB] knob

Turn this knob to DELAY or REVERB to switch to that eect.

Turn the knob to adjust the amount of eect applied.

* Graduations for each eect on a panel are for reference. Be

sure to check the sound as you adjust the eects.

Eect Explanation

DELAY

Turn the knob to change the time and amount of

delay eect.

REVERB Turn the knob to adjust the reverb level.

SPRING

This is modeled on spring reverb. It produces the

distinctive reverberations of a spring.

7 [GAIN] knob

Adjusts the amount of distortion and the input level.

8 [VOLUME] knob

Adjusts the volume of your electric guitar or microphone.

9 [TONE] knob

This adjusts the tone. Turn the knob clockwise for

a brighter tone; to get a milder tone, turn the knob

counterclockwise.

10 [MASTER] knob

Adjusts the overall volume.

11 [TUNER] button

Use this when you want to tune your guitar.

For details, refer to “Using the Tuner Function” (p. 9).

12 [POWER] switch

Turns the power on and o (p. 8). The power indicator will

light when you turn on the power.

Rear Panel

13 14 15 16 17

Headphones Recorder

13 Cord hook

To prevent the inadvertent disruption of power to your

unit (should the plug be pulled out accidentally), and to

avoid applying undue stress to the DC IN jack, anchor

the power cord using the cord hook, as shown in the

illustration.

14 DC IN jack

Connect the included AC adopter to this jack.

* Use only the AC adaptor included with the

MICRO CUBE GX. Use of other AC adaptors may damage

the amp or result in other problems.

15 Ground terminal

For details, refer to”Ground terminal” (p. 11).

16 REC OUT/PHONES jack

REC OUT

Connect a recorder, when recording the MICRO CUBE GX’s

output. Use mono miniature phone plugs when

connecting to this jack.

Use the [MASTER] knob to adjust the volume of the

signal output from REC OUT to the appropriate level.

PHONES

Connect headphones to this jack.

* The sound is output in mono.

* No sound is played through the unit’s speaker while the

REC OUT/PHONES jack is in use.

17 Security slot ( )

http://www.kensington.com/

8

Using the MICRO CUBE GX

Turning the Power On/O

* Once everything is properly connected, be sure to follow

the procedure below to turn on their power. If you turn

on equipment in the wrong order, you risk causing

malfunction or equipment failure.

1. Make sure that the MICRO CUBE GX’s

[MASTER] knob and the volume of any

connected device is set to 0.

* Set the [MASTER] knob to 0 before you connect anything

to the MICRO CUBE GX’s INPUT jack or i-CUBE LINK/AUX

IN jack.

2. Turn on all the devices connected to the

MICRO CUBE GX’s INPUT and i-CUBE LINK/

AUX IN jacks.

3. Turn on the MICRO CUBE GX.

* Before turning the unit on/o, always be sure to turn

the volume down. Even with the volume turned down,

you might hear some sound when switching the unit

on/o. However, this is normal and does not indicate a

malfunction.

* This unit is equipped with a protection circuit. A brief

interval (a few seconds) after turning the unit on is

required before it will operate normally.

4. Adjust the volume levels for the devices.

Before switching o the power, lower the volume on each

of the devices in your system and then TURN OFF the

devices in the reverse order to which they were switched

on.

Notes About Batteries

In addition to the AC adaptor, the MICRO CUBE GX can

also be powered with six AA batteries (optional). Insert

the batteries as shown in the gure, making sure that the

batteries are oriented correctly.

• If operating this unit on batteries, please disconnect the

AC adaptor from this unit.

• When you’re using the MICRO CUBE GX on batteries, all

the indicators will blink or become dim if the batteries

run low during your performance. Replace the batteries

as soon as possible.

• Sounds may distort easily or may cut o when played

at high volume as the battery power begins to fade, but

this is normal and does not indicate a malfunction. In

such instances, either replace the batteries or use the AC

adaptor included with the unit.

Caution when handling batteries

• If operating this unit on batteries, please use alkaline batteries, rechargeable Ni-MH batteries.

• When installing or replacing batteries, always turn this unit o and disconnect any other devices you may have

connected. This way, you can prevent malfunction and damage.

• If used improperly, batteries may explode or leak and cause damage or injury. In the interest of safety, please read and

observe the following precautions.

• Carefully follow the installation instructions for batteries, and make sure you observe the correct polarity.

• Avoid using new batteries together with used ones. In addition, avoid mixing dierent types of batteries.

• Remove the batteries whenever the unit is to remain unused for an extended period of time.

• Never keep batteries together with metallic objects such as ballpoint pens, necklaces, hairpins, etc.

• Used batteries must be disposed of in compliance with whatever regulations for their safe disposal that may be

observed in the region in which you live.

• Batteries must never be heated, taken apart, or thrown into re or water.

• Never expose batteries to excessive heat such as sunshine, re or the like.

• Incorrect handling of batteries can cause leakage, overheating, re, or explosion. Before use, you must read and strictly

observe all of the precautions that accompany the batteries, rechargeable batteries, or battery charger.

• When using rechargeable batteries and a charger, use only the combination of rechargeable batteries and charger

specied by the battery manufacturer.

• Expected battery life under continuous use:

Alkaline battery: 20 hours

Rechargeable Ni-MH battery: 25 hours

These gures will vary depending on the specications of the batteries and the actual conditions of use.

NederlandsPortuguêsEspañolItalianoFrançaisDeutschEnglish

Using the MICRO CUBE GX

9

Using the Memory Function

The unit’s memory lets you store the knob settings (see

illustration) for each of the eight amp types.

Storing Panel Settings in

Memory

Here’s how to store the current knob positions in memory.

1. Hold down the [MEMORY] button for several

seconds.

The MEMORY indicator will blink.

Once the settings have been stored, the indicator will

change to steadily lit.

NOTE

• When you store settings in memory, any settings

you’ve previously stored for the currently selected

amp type will be lost.

• The stored settings may be lost if you have the unit

serviced, if the unit malfunctions, or if you perform

an incorrect operation. Make a note of important

settings being stored to memory, so that you will

be able to reproduce them if they are lost. Roland

accepts no responsibility for the recovery of any

data stored in memory and assumes no liability with

regard to its loss.

Calling up the Memory

Here’s how to call up the knob positions (settings) you’ve

stored.

1. Press the [MEMORY] button so it’s lit.

2. Switch the amp type.

The settings stored for that amp type will be selected.

* If you move any knobs after calling up settings from

memory, the settings will change to the positions of the

knobs.

Using the Tuner Function

The MICRO CUBE GX provides a built-in tuner function. It

can be used not only as a chromatic tuner, but also as a

tuner for the open 5th string (“A” pitch).

* Use tuning the open 5th string (“A” pitch) when the strings

are substantially out of tune (such as after changing

strings).

Chromatic Tuning

1. Press the [TUNER] button so it’s lit.

The MICRO CUBE GX will enter tuner mode

and the [TUNER] button will light, allowing you

to use this function as a chromatic tuner that

automatically detects the name of the note

that is closest to the pitch you played.

In tuner mode, no sound will be output from

the speaker or any outputs.

2. Play a single note on the open string that

you want to tune.

Tune the string until the green indicator lights.

Pitch is

correct

Lights

green

Flat

Lights

red

Sharp

Lights

red

* The red indicator blinks if the pitch is substantially out

of tune.

3. When you have nished tuning, press the

[TUNER] button once again.

Tuning the Open 5th String

(“A” Pitch)

If you hold down the [TUNER] button for at least one

second, the [TUNER] button will blink, allowing you to

tune to the “A” pitch (open 5th string).

When tuning the open 5th string, you tune the string in

the same way as you do when using chromatic tuning—

by playing a single note and tuning it until the green

indicator lights.

* The reference pitch is A = 440 Hz. This cannot be changed.

Using the MICRO CUBE GX

10

Using i-CUBE LINK

“i-CUBE LINK” is a function that allows the MICRO CUBE GX

to be used simultaneously for conventional AUX IN and

as an audio interface for your iPad/iPhone when the iPad/

iPhone is connected via the included mini cable (4-pole).

This function lets you use an iPad/iPhone app to record

and play back the sound of your guitar.

iPad/iPhone

app

Guitar/mic sound

Sound will be input from

the iPad/iPhone to the

MICRO CUBE GX.

Guitar/

mic sound

iPad/iPhone

output

The sound of your guitar will be sent from

the MICRO CUBE GX to the iPad/iPhone.

* If you want to hear only the sound that’s being input from

the iPad/iPhone, turn down the [VOLUME] knob.

For details on i-CUBE LINK and on iPhone/iPad apps that

can use i-CUBE LINK, refer to Roland website.

http://www.roland.com/

Notes About Attaching the

Strap

Attach the strap securely so that it does not easily become

detached. If the strap is loose, and you use it that way

when carrying the MICRO CUBE GX, the amp could be

dropped, possibly resulting in damage or injury.

NOTE

• Use only the provided strap.

The included strap is meant for exclusive use with

the MICRO CUBE GX. Do not use this strap for other

products.

• Do not spin or swing the MICRO CUBE GX while

holding it by the strap. This is extremely dangerous, as

it may cause the strap to become detached; or, if the

motion is repeated enough, may even break the strap.

NederlandsPortuguêsEspañolItalianoFrançaisDeutschEnglish

Using the MICRO CUBE GX

11

Restoring the Factory

Settings

If you want to initialize all the knob settings stored in

memory, you can revert to the factory default settings as

follows (Factory Reset).

1. While holding down the [MEMORY] button,

turn on the power.

All indicators will blink, and the settings stored in memory

will return to their factory-set state.

NOTE

When you execute the factory reset procedure,

all knob settings that you’ve stored in the

MICRO CUBE GX will be lost.

Ground terminal

Depending on the circumstances of a particular setup, you may

experience a discomforting sensation, or perceive that the surface

feels gritty to the touch when you touch this device, microphones

connected to it, or the metal portions of other objects, such as

guitars. This is due to an innitesimal electrical charge, which is

absolutely harmless. However, if you are concerned about this,

connect the ground terminal with an external ground. When

the unit is grounded, a slight hum may occur, depending on the

particulars of your installation. If you are unsure of the connection

method, contact the nearest Roland Service Center, or an authorized

Roland distributor, as listed on the “Information” page.

Unsuitable places for connection

• Water pipes (may result in shock or electrocution)

• Gas pipes (may result in re or explosion)

• Telephone-line ground or lightning rod (may be dangerous in the event of lightning)

12

Specications

Rated Power

Output

3 W

Nominal Input

Level (1 kHz)

INPUT: -10 dBu / 1 M ohm

i-CUBE LINK / AUX IN: -10 dBu

Speaker 12 cm (5 inches) x 1

Controls

POWER switch

AMP TYPE switch (ACOUSTIC SIM, JC

CLEAN, BLACK PANEL, BRIT COMBO,

CLASSIC STACK, R-FIER STACK, EXTREME,

MIC)

MEMORY button

TUNER button

GAIN knob

VOLUME knob

TONE knob

EFX knob (CHORUS, FLANGER, PHASER,

TREMOLO, HEAVY OCTAVE)

DELAY / REVERB knob (DELAY, REVERB,

SPRING)

MASTER knob

Indicators

POWER

MEMORY

EFX

DELAY / REVERB

TUNER

Connectors

INPUT jack (1/4-inch phone type)

i-CUBE LINK / AUX IN jack (4-pole miniature

phone type)

REC OUT / PHONES jack (Stereo miniature

phone type)

DC IN jack

Power Supply

AC adaptor

Alkaline battery (AA, LR6) x 6

Rechargeable Ni-MH battery (AA, HR6) x 6

Current Draw 155 mA

Expected

battery life under

continuous use

Alkaline battery: Approximately 20 hours

Rechargeable Ni-MH battery:

Approximately 25 hours

(When using batteries having a capacity of

2,400 mAh.)

* This can vary depending on the capacity

of the batteries and the conditions

of use.

Dimensions

247 (W) x 172 (D) x 227 (H) mm

9-3/4 (W) x 6-13/16 (D) x 8-15/16 (H) inches

Weight

2.7 kg

6 lbs

Accessories

Owner’s Manual

AC adaptor

Strap

Mini cable (4-pole miniature phone type)

* 0 dBu = 0.775 Vrms

* In the interest of product improvement, the specications

and/or appearance of this unit are subject to change

without prior notice.

Roland MICRO CUBE GX: Guitar Amplier

NederlandsPortuguêsEspañolItalianoFrançaisDeutschEnglish

Bedienungsanleitung

Gitarrenverstärker

Bevor Sie das Gerät einsetzen, lesen Sie die Abschnitte “SICHERHEITSHINWEISE” (p. 2) und “WICHTIGE HINWEISE” (p. 5) sorgfältig

durch. Diese Abschnitte liefern wichtige Hinweise zum sicheren Betrieb des Geräts. Um sicherzustellen, dass Sie mit dem gesamten

Funktionsumfang des Gerätes vertraut sind, sollten Sie die Bedienungsanleitung vollständig lesen. Bewahren Sie diese Anleitung auf

und verwenden Sie diese zu Referenzzwecken.

Genehmigung von ROLAND CORPORATION.

i-CUBE LINK-Anschluss für die Verbindung zum iPad bzw. iPhone (p. 10)

•

Über den i-CUBE LINK-Anschluss können Sie Ihr Spiel mithilfe einer iPad/iPhone app aufnehmen und wiedergeben.

Zwei Möglichkeiten für die Stromversorgung (p. 8)

• Der MICRO CUBE GX kann entweder über sechs AA-Batterien oder über einen AC-Adapter mit Strom versorgt

werden. Bei Nutzung von Alkaline-Batterien kann der MICRO CUBE GX für ca. 20 Stunden eingesetzt werden

(abhängig von der Kapazität der Batterien und den Umgebungsbedingungen).

• Bei Nutzung von wieder auadbaren Ni-MH-Batterien kann der MICRO CUBE GX für ca. 25 Stunden eingesetzt

werden (abhängig von der Kapazität der Batterien und den Umgebungsbedingungen).

Sieben COSM Amp-Typen, acht Eekte und ein Mikrofoneingang (p. 6)

• Die sieben COSM-Verstärkertypen beinhalten die Einstellungen ACOUSTIC SIM, JC CLEAN, BLACK PANEL, BRIT

COMBO, CLASSIC STACK, R-FIER STACK und EXTREME.

• Es stehen zwei Eekt-Prozessoren mit acht Eekten zur Verfügung (EFX: CHORUS, FLANGER, PHASER,

TREMOLO, HEAVY OCTAVE), (DELAY/REVERB: DELAY, REVERB, SPRING).

• Der Mikrofoneingang ermöglicht den Einsatz als portablen Gesangs- bzw. Sprachverstärker.

COSM ( Composite Object Sound Modeling) ist eine innovative Sound Modeling-Technologie von Roland, welche die

einzelnen Faktoren des originalen Sounds nachbildet und daraus ein digitales Klangmodell erzeugt.

Speicherfunktion für eigene Einstellungen (p. 9)

• Sie können für jeden Verstärkertyp eine Einstellung sichern.

Der MICRO CUBE GX ist ein Gitarrenverstärker mit

3 Watt Ausgangsleistung und einem 2 cm (5-inch)

Lautsprecher.

2

SICHERHEITSHINWEISE

WARNUNG

Den AC-Adapter abziehen, um das Gerät vollständig

von der Stromversorgung zu trennen

Auch wenn das Gerät ausgeschaltet ist, ist dieses

immer noch am Stromnetz angeschlossen.

Wenn Sie das Gerät vollständig von der

Stromversorgung trennen möchten, müssen Sie

den Netzadapter aus der Steckdose ziehen.

Nicht selbst auseinanderbauen oder modizieren

Önen Sie weder das Gerät noch den

Netzadapter, und nehmen Sie keine Änderungen

daran vor.

Nicht selbst reparieren oder Teile austauschen

Versuchen Sie nicht, das Gerät zu reparieren

oder darin enthaltene Teile zu ersetzen (außer

in Fällen, für die in dieser Anleitung genaue

Anweisungen gegeben sind). Wenden Sie sich

bei allen Reparaturen an Ihren Fachhändler, ein

Roland Service Center in Ihrer Nähe oder an

einen der autorisierten Roland-Vertriebspartner, die auf der

Seite „Informationen“ aufgeführt sind.

Das Gerät nicht unter den folgenden

Umgebungsbedingungen verwenden oder lagern

• Extreme Temperaturen (z. B. direktes

Sonnenlicht in einem geschlossenen Fahrzeug,

in der Nähe einer Heizungsleitung, auf

Wärmequellen)

• Feuchtigkeit (z. B. Bäder, Waschräume, nasse

• Fußböden)

• Dampf oder Rauch

• Hoher Salzgehalt in der Luft

• Hohe Luftfeuchtigkeit

• Regen

• Staub oder Sand

• Starke Vibrationen oder Erschütterungen

WARNUNG

Nicht auf eine instabile Fläche stellen

Achten Sie darauf, dass das Gerät immer

waagerecht und stabil steht. Platzieren Sie es

nicht auf wackeligen Ständern oder auf schiefen

Standächen.

Ausschließlich den passenden Netzadapter und die

richtige Spannung verwenden

Verwenden Sie ausschließlich den angegebenen

Netzadapter, und achten Sie darauf, dass die

Netzspannung der Installation mit der auf dem

Netzadapter angegebenen Betriebsspannung

übereinstimmt. Andere Netzadapter haben

möglicherweise eine andere Polarität oder

sind auf eine andere Spannung ausgelegt. Ihre Verwendung

kann deshalb eine Beschädigung, Fehlfunktion oder einen

elektrischen Schlag zur Folge haben.

Das Netzkabel nicht knicken oder schwere

Gegenstände darauf stellen

Verdrehen oder biegen Sie das Netzkabel

nicht zu stark, und stellen Sie keine schweren

Gegenstände auf das Kabel. Dadurch kann

das Kabel beschädigt werden, was zu

Unterbrechungen und Kurzschlüssen führen

kann. Schadhafte Kabel können Brände und

elektrische Schläge verursachen!

Längeren Gebrauch mit hoher Lautstärke vermeiden

Dieses Gerät kann einzeln oder in Kombination

mit einem Verstärker und Kopfhörern oder

Lautsprechern Schallpegel erzeugen, die zu

dauerhaftem Gehörverlust führen können.

Betreiben Sie das Gerät nicht über längere Zeit

mit hoher oder unangenehmer Lautstärke.

Sobald Sie eine Beeinträchtigung Ihres Gehörs oder ein Klingeln

in den Ohren bemerken, sollten Sie den Betrieb des Geräts

sofort einstellen und sich an einen HNO-Arzt wenden.

Über die Hinweise WARNUNG und ACHTUNG

Das Symbol weist den Anwender auf Vorgänge hin, die niemals

ausgeführt werden dürfen (verboten sind). Welcher Vorgang genau

nicht ausgeführt werden soll, ist an der Abbildung innerhalb des

Kreises zu erkennen. Im Falle des links abgebildeten Symbols bedeutet

es hier, dass das Gerät niemals auseinander genommen werden darf.

Über die Symbole

ANWEISUNGEN ZUR VERMEIDUNG VON FEUER, ELEKTRISCHEM SCHLAG ODER PERSONENSCHÄDEN

Wird für Anweisungen verwendet, die

den Anwender vor Lebensgefahr oder der

Möglichkeit schwerer Verletzungen bei falscher

Anwendung des Geräts warnen sollen.

WARNUNG

Wird für Anweisungen verwendet, die den

Anwender vor Verletzungsgefahr oder der

Möglichkeit von Sachbeschädigung bei falscher

Anwendung des Gerätes warnen sollen.

* Als Sachbeschädigung werden Schäden

oder andere unerwünschte Auswirkungen

bezeichnet, die sich auf Haus/Wohnung und

die darin enthaltene Einrichtung sowie

Nutz- oder Haustiere beziehen.

ACHTUNG

Das Symbol weist den Anwender auf wichtige Anweisungen

oder Warnungen hin. Die genaue Bedeutung des Symbols ist an

der Abbildung innerhalb des Dreiecks zu erkennen. Im Falle des

links abgebildeten Symbols sind dies allgemeine Vorsichtsmaß-

nahmen, Warnungen oder Gefahrenhinweise.

Das Symbol weist den Anwender auf Vorgänge hin, die

ausgeführt werden müssen. Welcher Vorgang genau ausgeführt

werden soll, ist an der Abbildung innerhalb des Kreises zu

erkennen. Im Falle des links abgebildeten Symbols bedeutet es

hier, dass das Netzkabel aus der Steckdose gezogen werden muss.

BEACHTEN SIE IMMER FOLGENDES

NederlandsPortuguêsEspañolItalianoFrançaisDeutschEnglish

SICHERHEITSHINWEISE

3

WARNUNG

Eindringen von Fremdkörpern oder Flüssigkeiten in

das Gerät vermeiden und keine Behälter mit

Flüssigkeiten auf das Gerät stellen

Stellen Sie auf diesem Gerät keine mit

Flüssigkeiten gefüllten Behälter ab. Achten Sie

darauf, dass in das Gerät keine Fremdkörper (z. B.

brennbare Objekte, Münzen oder Drähte) oder

Flüssigkeiten (z. B. Wasser oder Saft) eindringen.

Dies kann zu Kurzschlüssen, Fehlfunktion oder

sonstigen Störungen führen.

Das Gerät bei unnormalem Verhalten oder

Fehlfunktion ausschalten

Schalten Sie das Gerät sofort aus, ziehen Sie den

Netzadapter aus der Steckdose, und wenden

Sie sich an Ihren Fachhändler, ein Roland-

Service-Center in Ihrer Nähe oder an einen der

autorisierten Roland-Vertriebspartner, die auf der

Seite „Informationen“ aufgeführt sind, wenn einer der folgenden

Fälle eintritt:

• Der Netzadapter, das Netzkabel oder der Stecker wurde

beschädigt.

• Rauch oder ein ungewöhnlicher Geruch tritt auf.

• Gegenstände oder Flüssigkeiten sind in das Gerät gelangt.

• Das Gerät war Regen (oder sonstiger Feuchtigkeit) ausgesetzt.

• Das Gerät scheint nicht normal zu funktionieren oder weist

eine deutliche Änderung der Leistungsfähigkeit auf.

Kinder müssen durch Erwachsene beaufsichtigt

werden

Wenn das Gerät in der Gegenwart von Kindern

verwendet wird, achten Sie darauf, dass das Gerät

nicht unsachgemäß bedient wird. Es sollten

immer beaufsichtigende Erwachsene anwesend

sein.

Nicht fallen lassen oder starken Stößen aussetzen

Schützen Sie das Gerät vor starken Stößen, und

lassen Sie es nicht fallen.

Nicht zusammen mit einer zu großen Anzahl von

Geräten an einer einzigen Netzsteckdose betreiben

Betreiben Sie den Netzadapter nicht zusammen

mit einer zu großen Anzahl von Geräten an einer

einzigen Netzsteckdose. Seien Sie besonders

vorsichtig beim Einsatz von Verlängerungskabeln

– die Gesamtleistung aller an der Verlängerung

betriebenen Geräte darf die für das

Verlängerungskabel angegebene zulässige Leistung (Watt-/

Ampère-Zahl) nicht überschreiten. Übermäßige Last kann dazu

führen, dass sich die Isolierung erhitzt und ggf. schmilzt.

WARNUNG

Nutzung des Gerätes im Ausland

Bevor Sie das Gerät in einem anderen Land

betreiben, wenden Sie sich an Ihren Fachhändler,

ein Roland-Service-Center in Ihrer Nähe oder an

einen der autorisierten Roland-Vertriebspartner

(siehe Seite „Informationen“).

Batterien sorgfältig behandeln

• Batterien dürfen niemals neu aufgeladen,

erhitzt, in ihre Einzelteile zerlegt oder ins Feuer

oder Wasser geworfen werden.

• Batterien dürfen niemals übermäßiger Hitze

wie Sonnenlicht, Feuer oder Ähnlichem

ausgesetzt werden.

• Eine unsachgemäße Handhabung von

Batterien kann zu Auslaufen, Überhitzung,

Feuer und Explosionen führen. Lesen Sie

vor der Verwendung von Batterien bzw.

Ladegeräten alle den Batterien beigefügten

Sicherheitshinweise, und beachten Sie diese

genau.

• Wenn Sie wieder auadbare Batterien sowie

ein Ladegerät verwenden, verwenden Sie

immer nur die vom Hersteller der Batterien

empfohlene Kombination von Batterien und

Ladegerät.

SICHERHEITSHINWEISE

4

VORSICHT

An einem gut belüfteten Standort aufstellen

Das Gerät und der Netzadapter sollten so

aufgestellt werden, dass deren Aufstellort oder

-position nicht die erforderliche Belüftung

beeinträchtigt.

Netzadapter mit dem Stecker anschließen und

trennen

Fassen Sie das Netzkabel des Netzadapters immer

am Stecker an, wenn Sie diesen in eine Steckdose

oder in das Gerät stecken oder herausziehen.

Stecker des Netzadapters regelmäßig reinigen

Sie sollten den Netzadapter in regelmäßigen

Abständen aus der Steckdose herausziehen und

die Kontakte am Stecker mit einem trockenen

Tuch von Staub und anderen Ablagerungen

reinigen. Ziehen Sie den Netzstecker auch dann

aus der Steckdose, wenn das Gerät längere

Zeit außer Betrieb ist. Jegliche Staubansammlung zwischen

Netzstecker und Steckdose kann die Isolierung beeinträchtigen

und zu Bränden führen.

Kabel sicher verlegen

Sorgen Sie dafür, dass Kabel und Leitungen nicht

durcheinander geraten. Achten Sie außerdem

darauf, dass sich alle Kabel und Leitungen

außerhalb der Reichweite von Kindern benden.

Nicht auf das Gerät steigen und keine schweren

Objekte darauf abstellen

Steigen Sie niemals auf das Gerät, und stellen Sie

keine schweren Gegenstände darauf ab.

Netzadapter nicht mit nassen Händen ein- oder

ausstecken

Fassen Sie den Netzadapter niemals mit nassen

Händen an, wenn Sie ihn in eine Steckdose oder

das Gerät stecken oder herausziehen.

Vor dem Bewegen des Gerätes alle Verbindungen

trennen

Trennen Sie die Verbindung des Netzadapters

mit der Steckdose sowie aller weiteren Kabel mit

externen Geräten, bevor Sie das Gerät bewegen.

Vor der Reinigung den Netzadapter von der

Steckdose trennen

Schalten Sie das Gerät vor der Reinigung aus, und

ziehen Sie den Netzadapter aus der Steckdose.

VORSICHT

Bei heraufziehenden Gewittern den Netzadapter von

der Steckdose trennen

Bei angekündigtem oder heraufziehendem

Gewitter sollte der Netzadapter immer von der

Steckdose getrennt werden.

Batterien sorgfältig behandeln

Bei falscher Handhabung können Batterien

explodieren oder auslaufen und Schäden oder

Verletzungen verursachen. Lesen und beachten

Sie daher im Interesse der Sicherheit die

folgenden Vorsichtsmaßnahmen (p. 8).

• Befolgen Sie sorgfältig die Anweisungen zum

Einsetzen der Batterien. Achten Sie dabei

genau auf die richtige Polarität.

• Verwenden Sie neue Batterien nicht

zusammen mit gebrauchten Batterien.

Verwenden Sie unterschiedliche Batterietypen

nicht gleichzeitig.

• Nehmen Sie die Batterien aus dem Gerät

heraus, wenn dieses längere Zeit außer Betrieb

ist.

• Bewahren Sie Batterien nicht zusammen mit metallischen

Gegenständen wie Kugelschreibern, Halsketten, Haarnadeln

usw. auf.

• Gebrauchte Batterien müssen gemäß den gesetzlichen

Bestimmungen Ihrer Region entsorgt werden.

Sorgfältiger Umgang mit dem Erdungsanschluss

Bringen Sie eine von der Erdungsklemme

entfernte Schraube wieder an, und lassen Sie

sie nicht dort liegen, wo sie von kleinen Kindern

verschluckt werden kann. Stellen Sie beim

Wiederanbringen der Schraube sicher, dass sie

fest sitzt und sich nicht wieder lockern kann.

Undichte Batterien vorsichtig behandeln

• Wenn aus einer Batterie Flüssigkeit austritt,

berühren Sie diese nicht mit bloßen Händen.

• Wenn die Flüssigkeit in die Augen gelangt,

kann dies zum Erblinden führen. Reiben

Sie nicht die Augen, sondern spülen Sie sie

gründlich mit sauberem Wasser. Suchen Sie

anschließend unverzüglich einen Arzt auf.

• Wenn Batterieüssigkeit in Kontakt mit der

Haut oder Kleidung gelangt, kann dies zu

Hautverbrennungen oder Hautentzündungen

führen. Spülen Sie die betroenen Stellen gründlich mit

sauberem Wasser, und suchen Sie unverzüglich einen Arzt auf.

• Wischen Sie restliche Batterieüssigkeit sorgfältig aus dem

Batteriefach. Setzen Sie dann neue Batterien ein.

NederlandsPortuguêsEspañolItalianoFrançaisDeutschEnglish

5

WICHTIGE HINWEISE

Stromversorgung

• Schließen Sie dieses Gerät nicht an

die gleiche Steckdose wie andere

elektrische Geräte an, die durch

einen Wechselrichter oder Motor

betrieben werden (z. B. Kühlschrank

oder Waschmaschine, da eventuell

erzeugte Interferenzen in der

Netzversorgung zu Fehlfunktionen

oder hörbaren Störgeräuschen führen

können. Verwenden Sie ggf. einen

Netzentstörlter.

• Der Netzadapter wird bei Dauerbetrieb

warm. Dies ist normal und kein Grund

zur Beunruhigung.

• Der Einsatz eines Netzadapters wird

Roland Micro Cube GX BK Le manuel du propriétaire

Ce manuel convient également à

Roland Micro Cube GX BK Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents