Crafstman CMXPTSG1010NB Le manuel du propriétaire

Marque: Crafstman

Modèle: CMXPTSG1010NB

Catégorie: Outils électroportatifs

Taper: Le manuel du propriétaire

Air Hammer

Martillo neumático

Marteau pneumatique

CMXPTSG1010NB

INSTRUCTION MANUAL | GUIDE D’UTILISATION | MANUAL DE INSTRUCCIONES

IF YOU HAVE QUESTIONS OR COMMENTS, CONTACT US.

POUR TOUTE QUESTION OU TOUT COMMENTAIRE, NOUS CONTACTER.

SI TIENE DUDAS O COMENTARIOS, CONTÁCTENOS.

1-888-331-4569 WWW.CRAFTSMAN.COM

ENGLISH

Components

Air Hammer

Spring Retainer

Chisel

Trigger

Cylinder

Air Inlet

Fig. A

Deﬁnitions: Safety Alert Symbols and Words

This instruction manual uses the following safety alert symbols and words to alert you to

hazardous situations and your risk of personal injury or property damage.

DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in

death or serious injury.

WARNING: Indicates a potentially hazardous situation which, if not avoided, could result

in death or serious injury.

CAUTION: Indicates a potentially hazardous situation which, if not avoided, may result in

minor or moderate injury.

NOTICE: Indicates a practice not related to personal injury which, if not avoided, may

result in property damage.

(Used without word) Indicates a safety related message.

WARNING: Read all safety warnings and all

instructions. Failure to follow the warnings

and instructions may result in electric shock, ﬁre

and/or serious injury.

WARNING: Never modify the product or any

part of it. Damage or personal injury could result.

WARNING: To reduce the risk of injury, read the

instruction manual.

If you have any questions or comments about

this or any product, call CRAFTSMAN toll free

at: 1-888-331-4569.

Speciﬁcations

Model CMXPTSG1010NB

Chisel Shank Diameter 0.401" (10.2 mm)

Stroke Length 1-5/8"

Blow Per Minute 2,800 b.p.m

Average Air Consumption 4.4 scfm

Air Inlet 1/4" npt

Air Hose 3/8" (9.53 mm)

Working Pressure 90 psi

Air Hammer

ENGLISH

WARNING: Failure to observe and follow safety instructions could result in injury or death.

WARNING: Improper operation or maintenance of this tool could result in serious injury

and property damage. Read and understand all warnings and operation instructions before

using this tool. When using any tool, basic safety precautions should always be followed to

reduce the risk of personal injury. Anticipate and be alert for sudden changes in motion

during startup and operation of any power tool. Do not operate tool if trigger does not turn

the tool on or oﬀ. Do not use this tool at heights exceeding 6 feet (2m). Use each tool for its

intended function only. Do not use this product in unsafe work conditions. It is always

recommended to keep a ﬁre extinguisher and ﬁrst aid kit near work areas.

WARNING: User must also read the compressor manual and follow all compressor safety

instructions

CMXPTSG1010NB

Compressor requirements

IMPORTANT: To operate correctly, this tool requires airﬂow that is at least 4.4 cubic feet per

minute (SCFM) at 90 pounds per square inch (PSI). Check the speciﬁcations of your air

compressor to be sure that it can support both the minimum SCFM and PSI required. The air

hose length could aﬀect how much air pressure the tool is actually receiving. You may need to

adjust the air pressure higher on the air regulator to achieve the working pressure of 90 PSI.

™

4.4 SCFM @ 90 PSI

Tool Requirements

Exigences relatives aux outils

Requisitos de herramientas

What can happen How to prevent it

This air powered tool is capable of propelling materials

such as fasteners, metal chips, and other debris at high

speed which could result in serious injury.

Always wear ANSI approved Z87.1 safety glasses.

Never leave operating tool unattended.

Disconnect tool from air supply when tool is not in use or

when changing accessories to prevent accidental operation.

Compressed air can be hazardous, propelling objects or

particles that can cause injury into soft tissues such as eyes

and ears.

For additional protection, use an approved face shield in

addition to safety glasses.

Tool attachments can become loose or break and ﬂy apart,

becoming projectiles or propelling other objects at the

operator or bystanders in the work area.

Make sure spring is on completely and tight prior to use.

ENGLISH

SAVE ALL WARNINGS AND INSTRUCTIONS

FOR FUTURE REFERENCE

What can happen How to prevent it

This tool is capable of generating sparks, which can result

in ignition of ﬂammable materials.

Never operate tools near ﬂammable substances such as

gasoline, naphtha, cleaning solvents, etc.

Work in a clean, well-ventilated area free of combustible

materials.

Never use oxygen, carbon dioxide or other bottled gases as

a power source for air tools.

What can happen How to prevent it

Exposure to noise produced by air tools can lead to

permanent hearing loss.

Always wear ANSI S3.19 hearing protection.

RISK OF EYE OR HEAD INJURY

WARNING

RISK OF FIRE OR EXPLOSION

RISK OF LOSS OF HEARING

ENGLISH

What can happen How to prevent it

This tool is not provided with an insulated gripping

surface. Contact with a “live” wire will also make exposed

metal parts of the tool “live” and can result in electrical

shock, electrocution or death.

Never use air tools where they may come in contact with

energized electrical wiring.

Air tool accessories that come into contact with hidden

electrical wiring could cause electrocution or death.

Thoroughly investigate workpieces and work areas for

possible hidden wiring before performing work.

What can happen How to prevent it

Loose hair, clothing, jewelry or other loose objects can

become entangled in the moving elements of this tool and

can cause serious injury.

Do not wear loose clothing, jewelry, or anything that may

get caught or tangled when using tool.

Remove any jewelry which may be caught by the tool.

Always keep hands and body parts away from moving

parts.

Always wear properly ﬁtted clothing and other properly

ﬁtted safety equipment when using this tool.

What can happen How to prevent it

This tool is capable of causing serious injury if operated

improperly, or in a manner for which the tool is not

intended.

Accessories can become extremely hot through friction

where they contact the workpiece.

Make sure hands are kept away from accessories during

tool use.

Keep the working part of the tool away from hands and

body.

Understand the tool’s limitations.

Read and understand instruction manual.

WARNING

RISK OF ELECTRIC SHOCK

RISK OF ENTANGLEMENT

RISK OF CUTS OR BURNS OR HAND ENTRAPMENT

ENGLISH

What can happen How to prevent it

A tool left unattended or with the air hose attached can be

activated by unauthorized persons leading to their injury

or injury to others.

Remove air hose when the tool is not in use and store tool

in a secure location away from reach of children and

untrained users.

Air tools can propel fasteners or other materials

throughout the work area.

Use only accessories recommended by the manufacturer.

Keep work area clean and free of clutter.

Do not allow children to operate tool, and keep children

away from the work area.

Keep work area well lit.

Keep bystanders a safe distance away from work area.

Anyone entering the work area must wear personal

protective equipment.

Fragments of workpiece or of a broken accessory may ﬂy

away and cause injury beyond immediate area of

operation.

Air tools can become activated by accident during

maintenance or tool changes.

Disconnect the tool from the air supply during accessory

changes, tool changes, maintenance or repair.

Never carry the tool by the air hose.

To avoid unintentional operation, never carry the tool with

the trigger depressed or engaged.

Only an authorized service representative should service

the tool.

Loss of control of the tool can lead to operator injury or

injury to others in the work area.

Before changing accessories, making repairs, or when tool

is not in use, shut oﬀ the air supply and release/drain air

pressure from hose.

Disconnect tool from air supply and store in a safe location.

Never use the tool while using medications, drugs or

alcohol.

Keep proper footing at all times when handling tools.

Slipping, tripping falling or over reaching are major

causes of serious injury and/or death.

Air tools can cause the workpiece to move upon contact,

leading to injury.

Always make sure the workpiece is secure. Use clamps or

other devices to prevent movement.

WARNING

RISK OF PERSONAL INJURY

ENGLISH

There is a risk of bursting if the tool is damaged. Follow lubrication instructions for best and safest

operation.

Follow instructions on how to properly change accessories.

Poor quality, improper or damaged attachments can

detach or ﬂy apart during operation, sending projectiles

through the work area and causing serious injury.

Always use tool attachments rated for the power tool.

Never use tools, which have been dropped, impacted, or

are damaged.

Do not apply excessive force to the tool; let the tool

perform the work.

Never use a tool that is leaking air, has missing or

damaged parts, or requires repairs.

Always follow assembly, operation, maintenance

instructions.

Improperly maintained tools and accessories can cause

serious injury.

Do not use damaged, frayed or deteriorated air hoses

and/or ﬁttings.

Maintain the tool and accessories with care.

Keep tools clean and properly oiled for best and safest

performance.

Do not lubricate tools with ﬂammable or volatile liquids

such as kerosene, diesel or jet fuel.

Repetitive motions, awkward positions and exposure to

vibration can be harmful to hands and arms.

Discontinue use of tool if discomfort, tingling feeling or

pain occurs.

Consult a physician before resuming use if any of these

symptoms occur.

Using an accessory not intended for a speciﬁc tool

increases the risk of injury to the operator and everyone

else in the work area.

Always use accessories and attachments designed for the

tool and the work at hand.

Do not improvise or modify tools or accessories.

Loss of control of the tool can lead to operator injury or

injury to others in the work area.

Keep tool handles dry, clean and free from oil/grease.

Stay alert. Use common sense. Do not operate tools when

you are tired.

FREE WARNING LABEL REPLACEMENT: If your warning labels become illegible or are

missing, call 1-888-331-4569 for a free replacement.

Do not remove any labels – replace any damaged label.

ENGLISH

NOTICE: Use threaded sealant tape (not

included) on the threading of the male

plug.

PREPARATION

ASSEMBLY

Estimated Assembly Time: 1 – 3 minutes

Before beginning the assembly of the product, make sure all parts are present. Compare parts

with package contents list. If any part is missing or damaged, do not attempt to assemble the

product.

Tools Required for Assembly (not included):

•

9/16 in. (14 mm) or adjustable wrench

1. Remove plastic air inlet protective cap

from air inlet .

2. Tighten male plug (not included),

turning clockwise with a wrench (not

included) for air tight connection.

DO NOT OVERTIGHTEN.

ENGLISH

NOTICE: Use the top hook on the

spring retainer to help screw the spring

onto the cylinder.

3. Place 2 – 3 drops of air tool oil (not

included) into the opening of the male

air plug before each use.

4. Insert chisel into the opening of

cylinder .

5. Screw the spring retainer onto

the cylinder by turning it

clockwise until ﬁrmly secured.

Top

hook

Bottom

hook

Clockwise

ENGLISH

NOTICE: Working pressure is the amount

of air pressure the tool sees when

operating.

NOTICE: Always be cautious of your hands

and ﬁnger placement while tool is running.

Always disconnect air supply when not in

use to prevent accidental ﬁring of the tool.

OPERATING

DISASSEMBLY

6. Connect the air hose to the male plug.

Set the working pressure at 90 PSI for

best tool performance.

1. To remove the chisel , hold onto the

bottom hook on the retaining spring

and turn the spring counterclockwise

or you can insert a screwdriver into the

hook to help turn the spring.

2. Refer to assembly instructions to install

a diﬀerent chisel .

1. Press the trigger to start the tool.

Top

hook

Bottom

hook

Counterclockwise

ENGLISH

WARNING: ALWAYS DISCONNECT TOOL FROM THE AIR SUPPLY BEFORE PERFORMING ANY

MAINTENANCE ON THE TOOL.

WARNING: Always make sure the tool is properly lubricated during operation. Proper

lubrication is shown in this instruction manual.

MAINTENANCE

An in-line oiler (not included) is recommended to help increase tool life and keep the tool

properly lubricated. The in-line oiler should be regularly checked and ﬁlled with air tool oil as

needed. Proper adjustment of the in-line oiler can be performed by placing a sheet of paper

next to the tool’s exhaust ports while holding the throttle completely open for 30 seconds.

When a light stain of oil collects on the paper, the oiler is properly adjusted. Excessive

amounts of oil should be avoided.

Recommended lubricants: air-tool oil or any other high grade turbine oil containing moisture

absorbent, rust inhibitors, metal wetting agents and an EP (Extreme Pressure) additive.

Consult your local retailer for further assistance in selecting air tool oil best suited for proper

lubrication.

Cleaning

WARNING: Blow dirt and dust out of all air vents with clean, dry air at least once a week.

To minimize the risk of eye injury, always wear ANSI Z87.1 approved eye protection when

performing this.

WARNING: Never use solvents or other harsh chemicals for cleaning the non-metallic

parts of the tool. These chemicals may weaken the plastic materials used in these parts.

Use a cloth dampened only with water and mild soap. Never let any liquid get inside the

tool; never immerse any part of the tool into a liquid.

Repairs

WARNING: To assure product SAFETY and RELIABILITY, repairs, maintenance should be

performed by a CRAFTSMAN factory service center or a CRAFTSMAN authorized service

center. Always use identical replacement parts.

Accessories

WARNING: Since accessories, other than those oﬀered by CRAFTSMAN, have not been

tested with this product, use of such accessories with this tool could be hazardous. To

reduce the risk of injury, only CRAFTSMAN recommended accessories should be used with

this product.

Recommended accessories for use with your tool are available at extra cost from your local

dealer or authorized service center. If you need assistance in locating any accessory, please visit

CRAFTSMAN.COM or call 1-888-331-4569.

ENGLISH

Storage

Before you store the tool, make sure you do the following:

Thank you for your purchase. Register your product now for:

1. Review the Maintenance section on the preceding pages and perform scheduled

maintenance as necessary.

2. Tool must be well cleaned and lightly lubricated before storing.

3. Store the tool in a dry, safe place out of the reach of children.

• WARRANTY SERVICE: Registering your product will help you obtain more eﬃcient

warranty service in case there is a problem with your product.

• CONFIRMATION OF OWNERSHIP: In case of an insurance loss, such as ﬁre, ﬂood or

theft, your registration of ownership will serve as your proof of purchase.

• FOR YOUR SAFETY: Registering your product will allow us to contact you in the unlikely

event a safety notiﬁcation is required under the Federal Consumer Safety Act.

ENGLISH

TROUBLESHOOTING

WARNING: If the tool runs slowly or will not operate, check these possible

problems and take the required corrective action:

PROBLEM CAUSE CORRECTION

Tool runs slowly or will

not operate.

Grit or gum in tool. Flush the tool with air-tool oil or gum solvent.

Tool runs slowly or will

not operate.

No oil in tool. Lubricate the tool.

Tool runs slowly or will

not operate.

Air hose leaks. Tighten and seal hose ﬁttings if leaks are found. Use

sealing tape.

Tool runs slowly or will

not operate.

Moisture blowing out

of tool exhaust.

Water in compressor tank; drain tank (See air

compressor manual).

Oil the tool and run until no water is evident. Oil the

tool again and run 1 – 2 seconds.

Tool runs slowly or will

not operate.

Low air pressure. Be sure the hose is the proper size. Long hoses or

tools using large volumes of air may require an

internal diameter of 1/2 in. I.D. or larger, depending

on total hose length.

Do not use multiple hoses connected together with

quick-connect ﬁttings. This causes additional loss of

pressure and reduces the tool power. Use single

hoses of the proper length.

Tool runs slowly or will

not operate.

Low air pressure. Adjust the regulator on the tool to the maximum

setting.

Adjust the compressor regulator to tool maximum

of 90 PSI.

NOTE: Air hoses may cause up to 15 PSI loss in

pressure, so you may need to set a higher

compressor output to maintain the required pressure

at the tool.

ENGLISH

Three Year Limited Warranty

CRAFTSMAN will repair or replace, without charge, any defects due to faulty materials or

workmanship for three years from the date of purchase (two years for batteries). This warranty

does not cover part failure due to normal wear or tool abuse. For further detail of warranty

coverage and warranty repair information, visit www.craftsman.com or call

1-888-331-4569. This warranty does not apply to accessories or damage caused where

repairs have been made or attempted by others. THIS LIMITED WARRANTY IS GIVEN IN LIEU

OF ALL OTHERS, INCLUDING THE IMPLIED WARRANTY OF MERCHANTABILITY AND FITNESS

FOR A PARTICULAR PURPOSE, AND EXCLUDES ALL INCIDENTAL OR CONSEQUENTIAL

DAMAGES. Some states do not allow limitations on how long an implied warranty lasts or the

exclusion or limitation of incidental or consequential damages, so these limitations may not

apply to you. This warranty gives you speciﬁc legal rights and you may have other rights

which vary in certain states or provinces.

90 DAY MONEY BACK GUARANTEE

If you are not completely satisﬁed with the performance of your CRAFTSMAN Power Tool,

Laser, or Nailer for any reason, you can return it within 90 days from the date of purchase with

a receipt for a full refund – no questions asked.

LATIN AMERICA: This warranty does not apply to products sold in Latin America. For

products sold in Latin America, see country speciﬁc warranty information contained in the

packaging, call the local company or see website for warranty information.

is a registered trademark of Stanley Black & Decker, Inc., used under license.

est une marque déposée de Stanley Black & Decker, Inc., utilisée sous licence.

es una marca registrada de Stanley Black & Decker, Inc., utilizada bajo licencia.

CRAFTSMAN®

U.S. & Canada Only • É.-U. et Canada seulement • EE.UU. y Canadá únicamente

Product Manufactured by: SHINING GOLDEN YIDA

Produit fabriqué par: SHINING GOLDEN YIDA

Producto fabricado por: SHINING GOLDEN YIDA

LICENSEE NAME: SHINING GOLDEN YIDA

LICENSEE ADDRESS: PO BOX 6564 AKRON, OH 44312

ENGLISH

Exploded Tool Diagram

ENGLISH

Part Qty

1 1

Description

Retaining Spring

2 1Chisel

3 1Cylinder

4 1Piston

5 1Air Valve Assembly

6 1Housing

7 1Trigger

8 1Screw

9 1Roll Pin

10 1Sleeve

11 1Washer

12 1Rubber Washer

13 1Air Inlet Valve

14 1Spring

15 1O-ring

16 1Exhaust Cover

17 1Air Inlet Connector

18 1Metal Filter

Parts List

Part

Kit Number

K66001-CMX Air Valve Assembly

Kit Description

Replacement Kits

Composants

Marteau pneumatique

Cale-ressort

Burin

Gâchette

Cylindre

Entrée d’air

Fig. A

FRANÇAIS

Déﬁnitions : symboles et termes de sécurité

Le présent manuel d’instructions comporte des symboles et des termes de sécurité visant à

vous informer qu’une situation peut s’avérer dangereuse et que des risques de blessures ou

de dommages matériels peuvent être présents.

DANGER : Indique un danger imminent qui, s’il n’est pas évité, peut causer des blessures

graves ou la mort.

AVERTISSEMENT : Indique une situation potentiellement dangereuse qui, si elle n’est pas

évitée, pourrait entraîner la mort ou des blessures graves.

ATTENTION : Indique un risque potentiel qui, s’il n’est pas éliminé, pourrait provoquer des

blessures mineures ou moyennement graves.

AVIS : Indique une pratique ne posant aucun risque de blessure qui, si elle n’est pas évitée,

peut entraîner des dommages matériels.

(Utilisé sans explication) Indique un message relatif à la sécurité.

AVERTISSEMENT : Lisez tous les avertissements

et toutes les instructions. Le non-respect des

avertissements et des instructions peut entraîner un

choc électrique, un incendie ou des blessures graves.

AVERTISSEMENT : Ne modiﬁez jamais l’article ou

l’une de ses parties. Cela pourrait endommager

l’article ou causer des blessures.

AVERTISSEMENT : Aﬁn de réduire les risques de

blessure, l’utilisateur doit lire le manuel d’instructions.

Si vous avez des questions ou des commentaires

concernant cet article ou tout autre article,

communiquez avec CRAFTSMAN en composant le

numéro sans frais suivant : 1 888 331-4569.

Caractéristiques techniques

Modèle CMXPTSG1010NB

Diamètre du burin 10,2 mm (0.401 po)

Course 4,12 cm

Coups par minute 2800 coups/minute

Consommation d’air moyenne 4,4 pi³/min standard

Entrée d’air 1/4 po, NPT

Tuyau à air 9,53 mm (3/8 po)

Pression de service 90 lb/po²

Marteau pneumatique

CMXPTSG1010NB

Exigences relatives au compresseur

™

4.4 SCFM @ 90 PSI

Tool Requirements

Exigences relatives aux outils

Requisitos de herramientas

FRANÇAIS

IMPORTANT : Pour fonctionner convenablement, cet outil nécessite un débit d’air d’au

moins 4,4 pi

/min standard à une pression de 90 lb/po

. Vériﬁez les spéciﬁcations de votre

compresseur d’air aﬁn de vous assurer qu’il satisfait aux exigences minimales (pi³/min

standard et lb/po²). La longueur du tuyau à air peut avoir une incidence sur la pression d’air

reçue par l’outil. Il est possible que vous ayez à augmenter la pression d’air sur le régulateur

de débit d’air aﬁn d’atteindre la pression de service de 90 lb/po².

AVERTISSEMENT : Le non-respect des consignes de sécurité peut entraîner des blessures

ou la mort.

AVERTISSEMENT : Une utilisation ou un entretien inadéquats de cet outil peut entraîner

des blessures graves ou des dommages matériels. Assurez-vous de lire et de comprendre

tous les avertissements et toutes les instructions avant d’utiliser l’outil. Lorsque vous utilisez

un outil, observez toujours les mesures de sécurité de base aﬁn de réduire les risques de

blessure. Soyez attentifs aux changements de mouvement soudains lors du démarrage et

de l’utilisation de tout outil à moteur et anticipez-les. N’utilisez pas l’outil si la gâchette ne

fonctionne pas pour la mise en marche ou l’arrêt de l’outil. N’utilisez pas cet outil à une

hauteur supérieure à 2 m (6 pi). Utilisez uniquement un outil, quel qu’il soit, pour l’usage

auquel il est destiné. N’utilisez pas cet article dans des conditions de travail dangereuses. Il

est toujours recommandé d’avoir un extincteur d’incendie et une trousse de premiers soins

à proximité des aires de travail.

AVERTISSEMENT : L’utilisateur doit également lire le manuel du compresseur et suivre

toutes les consignes de sécurité.

FRANÇAIS

Situations potentielles Mesures préventives

Cet outil pneumatique peut projeter des ﬁxations, des

fragments de métal et d’autres débris, ce qui peut causer

des blessures graves.

Portez toujours des lunettes de sécurité conformément à la

norme ANSI Z87.1.

Ne laissez jamais un outil en marche sans supervision.

Débranchez l’outil de l’alimentation en air lorsque vous ne

l’utilisez pas ou lorsque vous changez d’accessoire, aﬁn

d’éviter qu’il se déclenche accidentellement.

L’air comprimé peut être dangereux, car il est susceptible

de projeter des objets ou des particules pouvant causer

des blessures aux tissus mous du corps, notamment les

yeux et les oreilles.

Pour plus de protection, utilisez un écran facial approuvé et

portez des lunettes de sécurité.

Les accessoires de l’outil peuvent se desserrer ou se briser

et se détacher. Ils peuvent ainsi se transformer en projectiles

ou percuter d’autres objets et les projeter vers l’utilisateur

ou d’autres personnes se trouvant dans la zone de travail.

Assurez-vous que le ressort est complètement serré avant

l’utilisation.

CONSERVEZ TOUS LES AVERTISSEMENTS

ET TOUTES LES INSTRUCTIONS AFIN DE

POUVOIR LES CONSULTER ULTÉRIEUREMENT.

Situations potentielles Mesures préventives

Cet outil peut produire des étincelles susceptibles

d’enﬂammer certains matériaux.

N’utilisez jamais un outil à proximité d’une substance

inﬂammable comme de l’essence, du naphta, des solvants

de nettoyage, etc.

Travaillez dans un endroit propre, bien ventilé et dépourvu

de matériaux combustibles.

N’utilisez jamais d’oxygène, de dioxyde de carbone ni

d’autre gaz embouteillé comme source d’alimentation

pour les outils pneumatiques.

Situations potentielles Mesures préventives

L’exposition au bruit produit par les outils pneumatiques

peut entraîner une perte auditive permanente.

Portez toujours des protecteurs auditifs conformes à la

norme ANSI S3.19.

RISQUES DE BLESSURE AUX YEUX OU À LA TÊTE

AVERTISSEMENT

RISQUE D’INCENDIE OU D’EXPLOSION

RISQUE DE PERTE AUDITIVE

FRANÇAIS

AVERTISSEMENT

Situations potentielles Mesures préventives

La poignée de cet outil n’est pas isolée. Lorsque l’outil

entre en contact avec un ﬁl sous tension, ses parties

métalliques exposées peuvent causer des chocs

électriques, l’électrocution ou la mort.

N’utilisez jamais d’outils pneumatiques dans des endroits

où ils pourraient entrer en contact avec des ﬁls sous

tension.

Le contact d’accessoires pour outils pneumatiques avec

des ﬁls électriques dissimulés peut causer des chocs

électriques ou la mort.

Avant de commencer, vériﬁez soigneusement les pièces

travaillées et les aires de travail pour déceler les ﬁls

dissimulés.

Situations potentielles Mesures préventives

Les cheveux, les bijoux ou les vêtements amples peuvent

se prendre dans les pièces mobiles de cet outil et causer

des blessures graves.

Ne portez pas de vêtements amples, de bijoux, ni tout

autre article qui pourrait s’accrocher ou s’emmêler dans

l’outil lorsque vous utilisez l’outil.

Retirez tout bijou susceptible de s’accrocher dans l’outil.

Gardez toujours vos mains et les autres parties de votre

corps à distance des pièces en mouvement.

Portez toujours des vêtements et un équipement de

protection bien ajustés lorsque vous utilisez cet outil.

Situations potentielles Mesures préventives

Cet outil peut causer des blessures graves s’il est utilisé

d’une manière inadéquate ou autre que celle pour

laquelle il est conçu.

La friction des accessoires sur les pièces travaillées peut

rendre ces derniers extrêmement chauds.

Assurez-vous que les accessoires sont tenus à l’écart des

mains lors de l’utilisation de l’outil.

Prenez garde à vos mains lorsque vous utilisez l’outil.

Connaissez les limites de l’outil.

Assurez-vous de lire et de comprendre le manuel

d’instructions.

RISQUE DE CHOC ÉLECTRIQUE

RISQUE D’EMMÊLEMENT

RISQUE DE COUPURES, DE BRÛLURES OU DE COINCEMENT DES MAINS

La page charge ...

Crafstman CMXPTSG1010NB Le manuel du propriétaire

Marque: Crafstman

Modèle: CMXPTSG1010NB

Catégorie: Outils électroportatifs

Taper: Le manuel du propriétaire

Télécharger le PDF

rapport

dans d''autres langues

English: Crafstman CMXPTSG1010NB Owner's manual
español: Crafstman CMXPTSG1010NB El manual del propietario

Documents connexes

Autres documents

Campbell Hausfeld HL540100AV Mode d'emploi