Denon AVR-882 Manuel utilisateur

AV SURROUND RECEIVER

AVR-1802/882

OPERATING INSTRUCTIONS

MODE D’EMPLOI

B

3

0

2

6

7

98

2

3

6

7

MASTER VOLUME

AVR-1802

PRECISION AUDIO COMPONENT / AV SURROUND RECEIVER

VOLUME LEVEL

B

PHONES

CH VOLSURROUND

MODE

SURROUND

PARAMETER

ON / STANDBY

TONE

CONTROL

SELECT

EXT. ININPUT MODE

A

B

CINEMA EQ TONE DEFEATANALOG

SPEAKER

AUTO

ON / STANDBY

DTSPCM

SIGNAL

DIGITAL

INPUT

REMOTE

SENSOR

TUNER

CD

DVD / VDP

VCR-2

PHONO

V. AUX

TV / DBS

VCR-1

INPUT

UP MODEBAND MEMORY

SHIFT

CDR / TAPE

DOWN

VIDEO SELECT DIMMER STATUS

PRESET

UPDOWN

TUNING

OPTICAL VIDEO

V.AUX INPUT

L

AUDIO

R

AVR/AVC

DVD/VDP

TV VCR

AUDIO

CD

MD/CDR

VIDEO

POWER

OFF

ON

DVD/VDP

CDPHONO

TV/DBS

VCR-1 VCR-2

SURROUND

MODE

V.AUX

INPUT MODE

VIDEO SELECT

CDR / TAPE

TUNER SHIFT

CHANNEL

TAPE

·

VCR

TITLE

DISC SKIP+

CD·MD/CDR·DVD/VDP

STATUS MUTING

T.TONE

MASTER

VOL

CHANNEL

TV

SYSTEM

SET UP MENU

SELECT

RETURN DISPLAY

SURROUND

CH SELECT

VOLUME

REMOTE CONTROL UNIT RC-897

2

We greatly appreciate your purchase of this unit.

2

To be sure you take maximum advantage of all the

features this unit has to offer, read these instructions

carefully and use the set properly. Be sure to keep this

manual for future reference should any questions or

problems arise.

“SERIAL NO.

PLEASE RECORD UNIT SERIAL NUMBER ATTACHED TO

THE REAR OF THE CABINET FOR FUTURE REFERENCE”

“NO. DE SERIE

PRIERE DE NOTER LE NUMERO DE SERIE DE L’APPAREIL

INSCRIT A L’ARRIERE DU COFFRET DE FAÇON A POUVOIR

LE CONSULTER EN CAS DE PROBLEME.”

2

Nous vous remercions pour l’achat de cet appareil.

2

Pour être sûr de profiter au maximum de toutes les

caractéristiques qu’offre cet appareil, lire avec soin ces

instructions et bien utiliser l’appareil. Toujours

conserver ce mode d’emploi pour s’y référer

ultérieurement en cas de question ou de problème.

FOR ENGLISH READERS PAGE 2 ~ PAGE 48, 94, 95 POUR LES LECTEURS FRANCAIS PAGE 2, 49 ~ PAGE 95

2

ENGLISH

2 SAFETY PRECAUTIONS

2 NOTE ON USE / OBSERVATIONS RELATIVES A L’UTILISATION

• Avoid high temperatures.

Allow for sufficient heat dispersion when

installed on a rack.

• Eviter des températures élevées.

Tenir compte d’une dispersion de chaleur

suffisante lors de l’installation sur une étagère.

• Handle the power cord carefully.

Hold the plug when unplugging the cord.

• Manipuler le cordon d’alimentation avec

précaution.

Tenir la prise lors du débranchement du

cordon.

• Keep the set free from moisture, water, and

dust.

• Protéger l’appareil contre l’humidité, l’eau et la

poussière.

• Unplug the power cord when not using the set

for long periods of time.

• Débrancher le cordon d’alimentation lorsque

l’appareil n’est pas utilisé pendant de longues

périodes.

* (For sets with ventilation holes)

• Do not obstruct the ventilation holes.

• Ne pas obstruer les trous d’aération.

• Do not let foreign objects in the set.

• Ne pas laisser des objets étrangers dans

l’appareil.

• Do not let insecticides, benzene, and thinner

come in contact with the set.

• Ne pas mettre en contact des insecticides, du

benzène et un diluant avec l’appareil.

• Never disassemble or modify the set in any

way.

• Ne jamais démonter ou modifier l’appareil

d’une manière ou d’une autre.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK). NO

USER-SERVICEABLE PARTS INSIDE. REFER

SERVICING TO QUALIFIED SERVICE

PERSONNEL.

The lightning flash with arrowhead symbol, within an

equilateral triangle, is intended to alert the user to the

presence of uninsulated “dangerous voltage” within the

product’s enclosure that may be of sufficient magnitude to

constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended

to alert the user to the presence of important operating and

maintenance (servicing) instructions in the literature

accompanying the appliance.

WARNING:

TO REDUCE THE RISK OF FIRE OR ELECTRIC

SHOCK, DO NOT EXPOSE THIS APPLIANCE

TO RAIN OR MOISTURE.

CAUTION

TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG

TO WIDE SLOT, FULLY INSERT.

ATTENTION

POUR ÉVITER LES CHOCS ÉLECTRIQUES, INTERODUIRE LA

LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE

CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’ AU

FOND.

This device complies with Part 15 of the FCC Rules. Operation is subject to

the following two conditions: (1) This device may not cause harmful

interference, and (2) this device must accept any interference received,

including interference that may cause undesired operation.

This Class B digital apparatus meets all requirements of the Canadian

Interference-Causing Equipment Regulations.

Cet appareil numérique de la classe B respecte toutes les exigences du

Règlement sur le matériel brouilleur du Canada.

FRANCAIS

3

SAFETY INSTRUCTIONS

1. Read Instructions – All the safety and operating

instructions should be read before the appliance is

operated.

2. Retain Instructions – The safety and operating instructions

should be retained for future reference.

3. Heed Warnings – All warnings on the appliance and in the

operating instructions should be adhered to.

4. Follow Instructions – All operating and use instructions

should be followed.

5. Water and Moisture – The appliance should not be used

near water – for example, near a bathtub, washbowl,

kitchen sink, laundry tub, in a wet basement, or near a

swimming pool, and the like.

6. Carts and Stands – The appliance should be used only with

a cart or stand that is recommended by the manufacturer.

6A. An appliance and cart

combination should be

moved with care.

Quick stops, excessive

force, and uneven

surfaces may cause

the appliance and cart

combination to overturn.

7. Wall or Ceiling Mounting – The appliance should be

mounted to a wall or ceiling only as recommended by the

manufacturer.

8. Ventilation – The appliance should be situated so that its

location or position does not interfere with its proper

ventilation. For example, the appliance should not be

situated on a bed, sofa, rug, or similar surface that may

block the ventilation openings; or, placed in a built-in

installation, such as a bookcase or cabinet that may impede

the flow of air through the ventilation openings.

9. Heat – The appliance should be situated away from heat

sources such as radiators, heat registers, stoves, or other

appliances (including amplifiers) that produce heat.

10. Power Sources – The appliance should be connected to a

power supply only of the type described in the operating

instructions or as marked on the appliance.

11. Grounding or Polarization – Precautions should be taken so

that the grounding or polarization means of an appliance is

not defeated.

12. Power-Cord Protection – Power-supply cords should be

routed so that they are not likely to be walked on or

pinched by items placed upon or against them, paying

particular attention to cords at plugs, convenience

receptacles, and the point where they exit from the

appliance.

14. Cleaning – The appliance should be cleaned only as

recommended by the manufacturer.

15. Power Lines – An outdoor antenna should be located away

from power lines.

16. Outdoor Antenna Grounding – If an outside antenna is

connected to the receiver, be sure the antenna system is

grounded so as to provide some protection against voltage

surges and built-up static charges. Article 810 of the

National Electrical Code, ANSI/NFPA 70, provides

information with regard to proper grounding of the mast

and supporting structure, grounding of the lead-in wire to

an antenna-discharge unit, size of grounding conductors,

location of antenna-discharge unit, connection to grounding

electrodes, and requirements for the grounding electrode.

See Figure A.

17. Nonuse Periods – The power cord of the appliance should

be unplugged from the outlet when left unused for a long

period of time.

18. Object and Liquid Entry – Care should be taken so that

objects do not fall and liquids are not spilled into the

enclosure through openings.

19. Damage Requiring Service – The appliance should be

serviced by qualified service personnel when:

A. The power-supply cord or the plug has been damaged;

or

B. Objects have fallen, or liquid has been spilled into the

appliance; or

C. The appliance has been exposed to rain; or

D. The appliance does not appear to operate normally or

exhibits a marked change in performance; or

E. The appliance has been dropped, or the enclosure

damaged.

20. Servicing – The user should not attempt to service the

appliance beyond that described in the operating

instructions. All other servicing should be referred to

qualified service personnel.

FIGURE A

EXAMPLE OF ANTENNA GROUNDING

AS PER NATIONAL

ELECTRICAL CODE

ANTENNA

LEAD IN

WIRE

GROUND

CLAMP

ELECTRIC

SERVICE

EQUIPMENT

ANTENNA

DISCHARGE UNIT

(NEC SECTION 810-20)

GROUNDING CONDUCTORS

(NEC SECTION 810-21)

GROUND CLAMPS

POWER SERVICE GROUNDING

ELECTRODE SYSTEM

(NEC ART 250, PART H)

NEC - NATIONAL ELECTRICAL CODE

4

ENGLISH

2 INTRODUCTION

2 ACCESSORIES

Thank you for choosing the DENON A/V Surround receiver. This remarkable component has been engineered to provide superb surround sound

listening with home theater sources such as DVD, as well as providing outstanding high fidelity reproduction of your favorite music sources.

As this product is provided with an immense array of features, we recommend that before you begin hookup and operation that you review the

contents of this manual before proceeding.

TABLE OF CONTENTS

Check that the following parts are included in addition to the main unit:

1

BEFORE USING

Pay attention to the following before using this unit:

• Moving the set

To prevent short circuits or damaged wires in the connection cords,

always unplug the power cord and disconnect the connection

cords between all other audio components when moving the set.

• Before turning the power operation switch on

Check once again that all connections are proper and that there are

not problems with the connection cords. Always set the power

operation switch to the standby position before connecting and

disconnecting connection cords.

• Store this instructions in a safe place.

After reading, store this instructions along with the warranty in a

safe place.

• Note that the illustrations in this instructions may differ from

the actual set for explanation purposes.

• V. AUX terminal

The AVR-1802’s front panel is

equipped with a V. AUX terminal.

Remove the cap covering the

terminal when you want to use

it.

z

Before Using ..............................................................................................4

x

Cautions on Installation ..............................................................................5

c

Cautions on Handling .................................................................................5

v

Features......................................................................................................5

b

Part Names and Functions.....................................................................6, 7

n

Read this first .............................................................................................8

m

Setting up the Speaker Systems................................................................8

,

Connections .........................................................................................9~15

.

Using the Remote Control Unit................................................................16

⁄0

Setting up the system .......................................................................17~21

⁄1

Remote Control Unit..........................................................................22~24

⁄2

Operation ...................……………………………………………………25~29

⁄3

Surround.............................................................................................30~34

⁄4

DSP Surround Simulation .........…………………………………………35~39

⁄5

Listening to the Radio........................................................................40~42

⁄6

Last Function Memory .............................................................................43

⁄7

Initialization of the Microprocessor ......................…………………………43

⁄8

Additional Information........................................................................44~46

⁄9

Troubleshooting ........................................................................................47

¤0

Specifications ...........................................................................................48

List of Preset Codes..................................................................................94, 95

q Operating instructions ............................................................................1

w Warranty ( for North America model only ) ............................................1

e Service station list...................................................................................1

r Remote control unit (RC-897) .................................................................1

rt y ui

B

t R6P/AA batteries ....................................................................................2

y AM loop antenna ....................................................................................1

u FM indoor antenna..................................................................................1

i FM antenna adaptor................................................................................1

CH VOLSURROUND

MODE

SURROUND

PARAMETER

TONE

CONTROL

SELECT

E

AT

OPTICAL VIDEO

V.AUX INPUT

L

AUDIO

R

5

ENGLISH

3

CAUTIONS ON HANDLING

4

FEATURES

• Switching the input function when input jacks are not

connected

A clicking noise may be produced if the input function is switched

when nothing is connected to the input jacks. If this happens,

either turn down the MASTER VOLUME control or connect

components to the input jacks.

• Muting of PRE OUT jack, HEADPHONE jack and SPEAKER

terminals

The PRE OUT jack, HEADPHONE jack and SPEAKER terminals

include a muting circuit. Because of this, the output signals are

greatly reduced for several seconds after the power operation

switch is turned on or input function, surround mode or any other

set-up is changed.

If the volume is turned up during this time, the output will be very

high after the muting circuit stops functioning. Always wait until

the muting circuit turns off before adjusting the volume.

• Whenever the power operation switch is in the STANDBY

state, the apparatus is still connected on some AC line

voltages.

Please be sure to unplug the cord when you leave home for,

say, a vacation.

1. Dolby Pro Logic II decoder

Dolby Pro Logic II is a new format for playing multichannel audio

signals that offers improvements over conventional Dolby Pro

Logic. It can be used to decode not only sources recorded in

Dolby Surround but also regular stereo sources into five channels

(front left/right, center and surround left/right). In addition, various

parameters can be set according to the type of source and the

contents, so you can adjust the sound field with greater precision.

2. Dolby Digital decoder

Dolby Digital, a digital discrete system in which the different

channels are completely independent, recreates “three-

dimensional” sound fields (sounds with a sense of distance,

movement and position) with no crosstalk between channels for

greater reality. In addition, the 5 channels (excluding the 0.1

channel for low frequency effects) have a playback range

extending to 20 kHz, the same as the range of CDs, thus resulting

in clearer, more richly expressive sound.

3. DTS (Digital Theater Systems) decoder

DTS provides up to 5.1 channels of wide-range, high fidelity

surround sound, from sources such as laser disc, DVD and

specially-encoded music discs.

4. High performance DSP simulates 7 sound fields

Playback is possible in 7 surround modes: 5-channel Stereo, Mono

Movie, Rock Arena, Jazz Club, Video Game, Matrix and Virtual.

You can enjoy a variety of sound effects for different movie

scenes and program sources even with stereo sources not in

Dolby Surround.

5. Personal Memory Plus function

Personal Memory Plus is an advanced version of Personal

Memory. With Personal Memory Plus, the set automatically

memorizes the surround mode, channel volume, surround

parameters, etc., for each of the separate input sources.

6. Remote control unit with pre-memory function

This unit comes with a remote control unit equipped with a pre-

memory function. The remote control command codes for

DENON remote controllable AV components as well as for DVD

players, LD players, video decks, TVs, etc., of other major

manufacturers are prestored in the memory.

7. 6CH EXT. IN jack

This unit is equipped with 6CH EXT. IN jacks for use with audio

formats of the future.

2

CAUTIONS ON INSTALLATION

Noise or disturbance of the picture may be generated if this unit or

any other electronic equipment using microprocessors is used near a

tuner or TV.

If this happens, take the following steps:

• Install this unit as far as possible from the tuner or TV.

• Set the antenna wires from the tuner or TV away from this unit’s

power cord and input/output connection cords.

• Noise or disturbance tends to occur particularly when using indoor

antennas or 300 Ω/ohms feeder wires. We recommend using

outdoor antennas and 75 Ω/ohms coaxial cables.

For heat dispersal, leave at least 0.3 ft (10 cm) of space between

the top, back and sides of this unit and the wall or other

components.

B

0.3 ft (10 cm) or more

wall

0.3 ft (10 cm) or more

6

ENGLISH

5

PART NAMES AND FUNCTIONS

Front Panel

• For details on the functions of these parts, refer to the pages given in parentheses ( ).

VOLUME LEVEL

PHONES

CH VOLSURROUND

MODE

SURROUND

PARAMETER

ON / STANDBY

TONE

CONTROL

SELECT

EXT. ININPUT MODE

A

B

CINEMA EQ TONE DEFEATANALOG

SPEAKER

AUTO

ON / STANDBY

DTSPCM

SIGNAL

DIGITAL

INPUT

REMOTE

SENSOR

TUNER

CD

DVD / VDP

VCR-2

PHONO

V. AUX

TV / DBS

VCR-1

INPUT

UP MODEBAND MEMORY

SHIFT

CDR / TAPE

DOWN

VIDEO SELECT DIMMER STATUS

PRESET

UPDOWN

TUNING

B

AVR-1802

PRECISION AUDIO COMPONENT / AV SURROUND RECEIVER

MASTER VOLUME

OPTICAL VIDEO

V.AUX INPUT

L

AUDIO

R

#0

@7

@8@9

@6 @5 @4 @3 @2 @1 !6!7!9 !8@0

r y i !0 !1 !3 !4 !5q w e

t u o !2

q

Power operation switch ..............................................(18, 25, 40)

w

Headphones jack (PHONES)....................................................(28)

e

Preset stations selector buttons..............................................(42)

r

SPEAKER A/B buttons.................................................(25, 28, 43)

t

INPUT MODE button...................................................(26, 29, 33)

y

ANALOG button ................................................................(26, 29)

u

EXT. IN button ...................................................................(26, 29)

i

CINEMA EQ button .................................................................(33)

o

TONE DEFEAT button .............................................................(27)

!0

VIDEO SELECT button ............................................................(28)

!1

V. AUX INPUT jacks.............................................................(4, 10)

!2

SURROUND MODE button...................................(27, 31, 33, 38)

!3

SURROUND PARAMETER button.....................................(31, 38)

!4

SELECT knob ..................................................(27, 30, 31, 33, 38)

!5

TONE CONTROL button..........................................................(27)

!6

CH VOL button ........................................................................(30)

!7

MASTER VOLUME control......................................................(27)

!8

STATUS button ........................................................................(28)

!9

DIMMER button ......................................................................(28)

@0

Master volume indicator (VOLUME LEVEL)............................(27)

@1

Display

@2

TUNING UP/DOWN button .....................................................(41)

@3

MEMORY button...............................................................(40, 42)

@4

MODE button ..........................................................................(41)

@5

BAND button ...........................................................................(41)

@6

SIGNAL indicators....................................................................(27)

@7

INPUT mode indicators............................................................(27)

@8

Remote control sensor (REMOTE SENSOR) ..........................(19)

@9

Power operation indicator

#0

Input source selector buttons .....................................(26, 31, 33)

7

ENGLISH

Remote control unit

• For details on the functions of these parts, refer to the pages given in parentheses ( ).

B

DVD/VDP

CDPHONO

TV/DBS

VCR-1 VCR-2

SURROUND

MODE

TUNER SHIFT

REMOTE CONTROL UNIT RC-897

STATUS MUTING

T.TONE

MASTER

VOL

TITLE

DISC SKIP+

V. AUX

INPUT MODE CDR / TAPE

CHANNEL TV

CD·MD/CDR·DVD/VDP

VIDEO SELECT

SYSTEM

SET UP MENU

SELECT

RETURN DISPLAY

SURROUND

CH SELECT

VOLUME

CHANNEL

AVR/AVC

DVD/VDP

TV VCR

AUDIO

CD

MD/CDR

VIDEO

POWER

TAPE·VCR

OFF

8

4

9

5

1

0

6

2

7

3

ON

3

0

2

6

7

98

2

3

6

7

INPUT MODE button ...................(26, 29)

Cursor buttons.......................(17, 32, 36)

System buttons (TV) ..........................(24)

Test tone button.................................(30)

Remote control signal

transmitter .........................................(16)

Master volume control

buttons...............................................(27)

POWER buttons ....................(23, 24, 25)

MUTING button .................................(28)

Mode selector switch............(17, 22, 23)

Input source selector

buttons...................................(26, 31, 33)

Preset stations select

buttons.........................................(22, 42)

System buttons

(CD, MD/CDR, DVD/VDP) ............(22, 24)

SYSTEM (SYSTEM SET UP)

buttons...............................................(18)

System buttons (TAPE, VCR)

buttons.........................................(22, 24)

VIDEO SELECT button.......................(28)

SURROUND MODE

button ........................(27, 30, 31, 33, 36)

SURROUND (SURROUND PARAMETER)

button ..............................(31, 33, 34, 36)

STATUS button...................................(28)

8

ENGLISH

6

READ THIS FIRST

This AV Surround Receiver must be setup before use. Following these steps.

2 Speaker system layout

Basic system layout

• The following is an example of the basic layout for a system consisting of six speaker systems and a television monitor:

Subwoofer Center speaker system

Surround speaker systems

Front speaker systems

Set these at the sides of the TV or screen with

their front surfaces as flush with the front of the

screen as possible.

7

SETTING UP THE SPEAKER SYSTEMS

Step 3 (page 17 to 21)

Finally, setting up the system.

Step 2 (page 16)

Next, insert the batteries into the remote control unit.

Step 1 (page 8 to 15)

Choose the best location to setup the Speakers and connecting the components.

9

ENGLISH

8

CONNECTIONS

• Do not plug in the power cord until all connections have been

completed.

• Be sure to connect the left and right channels properly (left with

left, right with right).

• Insert the plugs securely. Incomplete connections will result in

the generation of noise.

• Use the AC OUTLETS for audio equipment only. Do not

use them for hair driers, etc.

• Note that binding pin plug cords together with power cords or

placing them near a power transformer will result in generating

hum or other noise.

• Noise or humming may be generated if a connected audio

equipment is used independently without turning the power

of this unit on. If this happens, turn on the power of this unit.

Connecting the audio components

CDR /

TAPE

CDR /

TAPE

DVD /

VDP

TV /

DBS

DVD /

VDP

TV /

DBS

VCR

-1

VCR

-2

VCR

-1

VCR

-2

VCR-1

FRONT

PREOUT

CENTER

DVD/

VDP

TV/

DBS

VCR-1 VCR-2

S-VIDEO

VCR-1 VCR-2

MONITOR

SUB

WOOFER

SPEAKER SYSTEMS AC OUTLETS

SURROUND AC 120V 60Hz

SWITCHED

TOTAL 120W(1A.)MAX.

PHONO

CD

SIGNAL

GND

MONITOR

VCR-2

VCR-1

VCR-2OPT-2

OPT-2

OPT-1FL

AM

ANTENNA TERMINALS

LOOP

ANT.

FM

COAX.

75

SL

EXT. IN AUDIO DIGITAL VIDEO

C

FR

SR

SW

COAX.

SPEAKER IMPEDANCE

FRONT A OR B / 6 16

A + B / 12 16

CENTER / 6 16

SURROUND / 6 16

R

OUTPUTINPUT

LRL

R

L

R

L

R

L

R

L

R

L

R

L

R

SUBWOOFER

FRONT

LINE OUT

LINE IN

CENTER

SURROUND

LINE OUT

Decoders with 6-channel

analog outputs, etc.

Connecting the AC OUTLETS

AC OUTLETS

• SWITCHED

(total capacity – 120 W (1 A.))

The power to these outlets is turned on and off in conjunction with the POWER switch on the main

unit, and when the power is switched between on and standby from the remote control unit.

No power is supplied from these outlets when this unit’s power is at standby. Never connect

equipment whose total capacity is above 120 W (1 A.)

NOTE:

Only use the AC OUTLETS for audio equipment. Never use them for hair driers, TVs or other

electrical appliances.

AC CORD

AC 120V, 60Hz

Connecting a tape deck

Connections for recording:

Connect the tape deck’s recording input jacks (LINE IN or REC) to this

unit’s tape recording (OUT) jacks using pin plug cords.

Connections for playback:

Connect the tape deck’s playback output jacks (LINE OUT or PB) to

this unit’s tape playback (IN) jacks using pin plug cords.

Tape deck or CD recorder

Connecting a turntable

Connect the turntable’s output cord to this

unit’s PHONO jacks, the L (left) plug to the L

jack, the R (right) plug to the right jack.

NOTE:

This unit cannot be used with MC

cartridges directly. Use a separate head

amplifier or step-up transformer.

If humming or other noise is generated when

the ground wire is connected, disconnect the

ground wire.

Turntable

(MM cartridge)

Ground wire

Use these jacks if you wish to connect external power amplifier(s) to increase the

power of the front and center channels, or for connection to powered loudspeakers.

Connect the internal amplifier’s subwoofer to the subwoofer terminal. (Refer to

page 14.)

Connecting the pre-out jacks

• Analog recording of signals input to the AVR-1802 in digital format is not possible. To record in analog, also connect the analog signals of the

player to the AVR-1802’s analog input terminals.

• The AVR-1802’s OPTICAL OUT terminal is an optical digital output terminal for connection of a CDR recorder, MD recorder or other digital

recording device. Use it for digital recording.

10

ENGLISH

CDR /

TAPE

CDR /

TAPE

DVD /

VDP

TV /

DBS

DVD /

VDP

TV /

DBS

VCR

-1

VCR

-2

VCR

-1

VCR

-2

VCR-1

FRONT

PREOUT

CENTER

DVD/

VDP

TV/

DBS

VCR-1 VCR-2

S-VIDEO

VCR-1 VCR-2

MONITOR

SUB

WOOFER

SPEAKER SYSTEMS AC OUTLETS

SURROUND AC 120V 60Hz

SWITCHED

TOTAL 120W(1A.)MAX.

PHONO

CD

SIGNAL

GND

MONITOR

VCR-2

VCR-1

VCR-2OPT-2

OPT-2

OPT-1FL

AM

ANTENNA TERMINALS

LOOP

ANT.

FM

COAX.

75

SL

EXT. IN AUDIO DIGITAL VIDEO

C

FR

SR

SW

COAX.

SPEAKER IMPEDANCE

FRONT A OR B / 6 16

A + B / 12 16

CENTER / 6 16

SURROUND / 6 16

OPTICALCOAXIAL

R

L

DIGITAL AUDIODIGITAL AUDIO

RL

R

L

OUTPUT

OPTICAL

DIGITAL AUDIODIGITAL AUDIO

LINE OUT

OUTPUT

DIGITAL OUT

DIGITAL IN

OUTPUT

B

INPUT

Connecting a CD player

Connect the CD player’s analog output

jacks (ANALOG OUTPUT) to this unit’s

CD jacks using pin plug cords.

CD player, etc. equipped

with DIGITAL output

DIGITAL jacks

Use these for connections to audio equipment with digital output.

Refer to page 21 for instructions on setting this terminal.

CD player

• Use 75 Ω/ohms cable pin cords (sold separately) for coaxial

connections.

• Use optical cables (sold separately) for optical connections,

removing the cap before connecting.

CD recorder, MD recorder or other component

equipped with digital output jacks.

Connecting the video equipments

To connect the video signal, connect using a 75 Ω/ohms video signal cable cord. Using an improper cable can result in a drop in sound quality.

VOLUME LEVEL

CH VOLSURROUND

MODE

SURROUND

PARAMETER

TONE

CONTROL

SELECT

VIDEO SELECT DIMMER STATUS

MASTER VOLUME

OPTICAL VIDEO

V.AUX INPUT

L

AUDIO

R

R VIDEO OUTOPTICALL

R VIDEO OUTL

OUTPUT

LINE OUT

DIGITAL OUT

VIDEO OUT

LINE OUT

L

R

L

R

L

R

Connecting a TV game equipment

• Connect the TV game equipment’s output jacks to

this unit’s V. AUX INPUT lacks.

TV game

Video camera

Connecting a video camera equipment

• Connect the video camera equipment’s output

jacks to this unit’s V. AUX INPUT lacks.

The V. AUX terminal is covered with a cap. Remove this cap in order to use the terminal. (See page 4 for instructions on removing the cap.)

11

ENGLISH

CDR /

TAPE

CDR /

TAPE

DVD /

VDP

TV /

DBS

DVD /

VDP

TV /

DBS

VCR

-1

VCR

-2

VCR

-1

VCR

-2

VCR-1

PHONO

CD

SIGNAL

GND

MONITOR

VCR-2

VCR-1

VCR-2OPT-2

OPT-2

OPT-1FL

AM

ANTENNA TERMINALS

LOOP

ANT.

FM

COAX.

75

SL

EXT. IN AUDIO DIGITAL VIDEO

C

FR

SR

SW

COAX.

R OUT

VIDEO

OUT

L

AUDIO

OUT

COAXIAL

DIGITAL

R OUT

VIDEO

OPTICAL

OUT

L

AUDIO

OUT

DIGITAL

R OUT IN

AUDIO

VIDEO

OUT IN

LRL

R

L

R

L

R OUT IN

AUDIO

VIDEO

OUT IN

LRL

R

L

R

L

OPT.-1

R

L

R

L

R

L

R

L

R

L

R

L

R

L

IN

VIDEO

B

TV or DBS tuner

DVD player or video disc player (VDP)

Monitor TV

Connecting a TV/DBS tuner

TV/DBS

• Connect the TV’s or DBS tuner’s video output jack (VIDEO OUTPUT)

to the (yellow) TV/DBS IN jack using a 75 Ω/ohms video

coaxial pin plug cord.

• Connect the TV’s or DBS tuner’s audio output jacks (AUDIO

OUTPUT) to the TV/DBS IN jacks using pin plug cords.

AUDIO

VIDEO

Connecting a DVD player or a video disc player VDP

• Connect the DVD player’s (video disc player’s) video output jack (VIDEO OUTPUT) to the (yellow) DVD/VDP

IN jack using a 75 Ω/ohms video coaxial pin plug cord.

• Connect the DVD player’s (video disc player’s) analog audio output jacks (ANALOG AUDIO OUTPUT) to the

DVD/VDP IN jacks using pin plug cords.

• For better sound quality, we recommend using the DVD player with digital rather than analog connections.

DVD players and VDP can also be connected to the VCR terminals.

AUDIO

VIDEO

MONITOR OUT

• Connect the TV’s video input jack (VIDEO

INPUT) to the MONITOR OUT

jack using a 75 Ω/ohms video coaxial pin

plug cord.

VIDEO

NOTE:

Connection of the video disc Player Equipped with Dolby Digital RF

(AC-3RF) Output Jack.

• Please use a commercially available adaptor when connecting the

Dolby Digital RF (AC-3RF) output jack of the video disc player to

the digital input jack.

Please refer to the instruction manual of the adapter when making

connections.

Video deck 2

• There are two sets of video deck (VCR) jacks, so two video decks can be connected for simultaneous recording or video copying.

Video input/output connections:

• Connect the video deck’s video output jack (VIDEO OUT) to the (yellow) VCR-1 IN jack, and the video deck’s video input jack (VIDEO IN) to the

(yellow) VCR-1 OUT jack using 75 Ω/ohms video coaxial pin plug cords.

Connecting the audio output jacks:

• Connect the video deck’s audio output jacks (AUDIO OUT) to the VCR-1 IN jacks, and the video deck’s audio input jacks (AUDIO IN) to the VCR-1

OUT jacks using pin plug cords.

Connect the second video deck to the VCR-2 jacks in the same way.

AUDIOAUDIO

VIDEOVIDEO

Connecting a video decks

VIDEO OUT

VIDEO IN

AUDIO OUT

VIDEO OUT

AUDIO OUT

AUDIO IN

Video deck 1

AUDIO IN

AUDIO OUT

VIDEO OUT

VIDEO IN

DIGITAL OUT

12

ENGLISH

Connecting a video component equipped with S-video jacks

• When marking connections, also refer to the operating instructions of the other components.

• A note on the S input jacks

The input selectors for the S inputs and pin jack inputs work in conjunction with each other.

• Precaution when using S-jacks

This unit’s S-jacks (input and output) and video pin jacks (input and output) have independent circuit structures, so that video signals input from

the S-jacks are only output from the S-jack outputs and video signals input from the pin jacks are only output from the pin jack outputs.

When connecting this unit with equipment that is equipped with S-jacks, keep the above point in mind and make connections according to the

equipment’s instruction manuals.

FRONT

PREOUT

CENTER

DVD/

VDP

TV/

DBS

VCR-1 VCR-2

S-VIDEO

VCR-1 VCR-2

MONITOR

SUB

WOOFER

SPEAKER SYSTEMS AC OUTLETS

SURROUND AC 120V 60Hz

SWITCHED

TOTAL 120W(1A.)MAX.

SPEAKER IMPEDANCE

FRONT A OR B / 6 16

A + B / 12 16

CENTER / 6 16

SURROUND / 6 16

IN

S-VIDEO

OUT

S-VIDEO

OUT

S-VIDEO

OUT IN

S-VIDEO

B

DVD player, VDP, etc.

Connecting a DVD player or video disc player (VDP)

DVD/VDP

• Connect the DVD player’s or video disc player’s S-Video output jack

to the S-VIDEO DVD/VDP IN jack using an S-Video connection cord.

Connecting a monitor TV

MONITOR OUT

• Connect the TV’s or DBS tuner’s S video input (S-VIDEO INPUT) to the

MONITOR OUT jack using a S jack connection cord.

S-VIDEO

Monitor TV

Connecting a TV/DBS tuner

• Connect the TV’s or DBS tuner’s S video

output jack (S-VIDEO OUTPUT) to the

TV/DBS IN jack using an S jack

connection cord.

S-VIDEO

TV or satellite broadcast tuner

Video deck 1

Connecting the video decks

• Connect the video deck’s S output jack (S-OUT) to the

VCR-1 IN jack and the video deck’s S input jack (S-IN) to the

VCR-1 OUT jack using S jack connection cords.

• Connect the video deck’s S output jack (S-OUT) to the

VCR-2 IN jack and the video deck’s S input jack (S-IN) to the

VCR-2 OUT jack using S jack connection cords.

S-VIDEO

Connect the components’ audio inputs and outputs as described on page 11.

Video deck 2

13

ENGLISH

1

4

2

3

Connecting the antenna terminals

CDR /

TAPE

CDR /

TAPE

DVD /

VDP

TV /

DBS

DVD /

VDP

TV /

DBS

VCR

-1

VCR

-2

VCR

-1

VCR

-2

VCR-1

PHONO

CD

SIGNAL

GND

MONITOR

VCR-2

VCR-1

VCR-2OPT-2

OPT-2

OPT-1FL

AM

ANTENNA TERMINALS

LOOP

ANT.

FM

COAX.

75

SL

EXT. IN AUDIO DIGITAL VIDEO

C

FR

SR

SW

COAX.

DIRECTION OF

BROADCASTING

STATION

AM LOOP

ANTENNA

(An Accessory)

FM ANTENNA

GROUND

AM OUTDOOR

ANTENNA

FM INDOOR ANTENNA

(An Accessory)

FEEDER

CABLE

75 Ω/ohms

COAXIAL

CABLE

AM loop antenna assembly

Connect to the AM

antenna terminals.

Bend in the reverse

direction.

Remove the vinyl tie

and take out the

connection line.

a. With the antenna

on top any stable

surface.

b. With the antenna

attached to a

wall.

Mount

Installation hole

Mount on wall, etc.

Connection of AM antennas

1. Push the lever. 2. Insert the

conductor.

3. Return the lever.

Note to CATV system installer:

This reminder is provided to call the CATV system installer’s

attention to Article 820-40 of the NEC which provides guidelines

for proper grounding and, in particular, specifies that the cable

ground shall be connected to the grounding system of the

building, as close to the point of cable entry as practical.

Notes:

• Do not connect two FM antennas simultaneously.

• Even if an external AM antenna is used, do not disconnect the

AM loop antenna.

• Make sure AM loop antenna lead terminals do not touch metal

parts of the panel.

14mm

9mm

14mm

19mm

5mm

5C-2V3C-2V

Open the cover

ANTENNA ADAPTER

REMOVE

CLAMP

75 Ω/ohms COAXIAL CABLE

CLAMP

PULL

SHUT

FM antenna adapter assembly

FM ANTENNA

ADAPTER

(An Accessory)

14

ENGLISH

Speaker system connections

• Connect the speaker terminals with the speakers making sure that like

polarities are matched (< with <, > with >). Mismatching of polarities will

result in weak central sound, unclear orientation of the various instruments,

and the sense of direction of the stereo being impaired.

• When making connections, take care that none of the individual conductors

of the speaker cord come in contact with adjacent terminals, with other

speaker cord conductors, or with the rear panel.

Speaker Impedance

• When speaker systems A and B are use separately, speakers with an

impedance of 6 to 16 Ω/ohms can be connected for use as front speakers.

• Be careful when using two pairs of front speakers (A + B) at the same time,

since use of speakers with an impedance of 12 to 16 Ω/ohms.

• Speakers with an impedance of 6 to 16 Ω/ohms can be connected for use

as center and surround speakers.

• The protector circuit may be activated if the set is played for long periods of

time at high volumes when speakers with an impedance lower than the

specified impedance are connected.

NOTE:

NEVER touch the speaker terminals when the power is on.

Doing so could result in electric shocks.

Connecting the speaker cords

1. Loosen by turning

counterclockwise.

2. Insert the cord. 3. Tighten by turning

clockwise.

Connecting banana plugs

Turn clockwise to tighten, then insert the

banana plug.

CDR /

TAPE

CDR /

TAPE

DVD /

VDP

TV /

DBS

DVD /

VDP

TV /

DBS

VCR

-1

VCR

-2

VCR

-1

VCR

-2

VCR-1

FRONT

PREOUT

CENTER

DVD/

VDP

TV/

DBS

VCR-1 VCR-2

S-VIDEO

VCR-1 VCR-2

MONITOR

SUB

WOOFER

SPEAKER SYSTEMS AC OUTLETS

SURROUND AC 120V 60Hz

SWITCHED

TOTAL 120W(1A.)MAX.

PHONO

CD

SIGNAL

GND

MONITOR

VCR-2

VCR-1

VCR-2OPT-2

OPT-2

OPT-1FL

AM

ANTENNA TERMINALS

LOOP

ANT.

FM

COAX.

75

SL

EXT. IN AUDIO DIGITAL VIDEO

C

FR

SR

SW

COAX.

SPEAKER IMPEDANCE

FRONT A OR B / 6 16

A + B / 12 16

CENTER / 6 16

SURROUND / 6 16

(

L

)(

R

)

(

L

) (

R

) (

L

) (

R

)

Connection jack for subwoofer with built-in

amplifier (super woofer), etc.

To achieve Dolby Digital (AC-3) playback

effect, use a unit that can sufficiently

reproduce frequencies of under 80 Hz.

SURROUND SPEAKER SYSTEMS

CENTER SPEAKER SYSTEM

FRONT SPEAKER SYSTEMS

• Precautions when connecting speakers

If a speaker is placed near a TV or video monitor, the

colors on the screen may be disturbed by the

speaker’s magnetism. If this should happen, move

the speaker away to a position where it does not

have this effect.

banana plug

System B

FRONT SPEAKER SYSTEMS

System A

15

ENGLISH

Protector circuit

• This unit is equipped with a high-speed protection circuit. The purpose of this circuit is to protect the speakers under

circumstances such as when the output of the power amplifier is inadvertently short-circuited and a large current flows,

when the temperature surrounding the unit becomes unusually high, or when the unit is used at high output over a long

period which results in an extreme temperature rise.

When the protection circuit is activated, the speaker output is cut off and the power supply indicator LED flashes. Should

this occur, please follow these steps: be sure to switch off the power of this unit, check whether there are any faults with

the wiring of the speaker cables or input cables, and wait for the unit to cool down if it is very hot. Improve the ventilation

condition around the unit and switch the power back on.

If the protection circuit is activated again even though there are no problems with the wiring or the ventilation around the

unit, switch off the power and contact a DENON service center.

Note on speaker impedance

• The protector circuit may be activated if the set is played for long periods of time at high volumes when speakers with

an impedance lower than the specified impedance (for example speakers with an impedance of lower than 4 Ω/ohms)

are connected. If the protector circuit is activated, the speaker output is cut off. Turn off the set’s power, wait for the set

to cool down, improve the ventilation around the set, then turn the power back on.

16

ENGLISH

9

USING THE REMOTE CONTROL UNIT

Following the procedure outlined below, insert the batteries before using the remote control unit.

Range of operation of the remote control unit

Inserting the batteries

B

Point the remote control unit at the remote control sensor as shown

on the diagram at the left.

NOTES:

• The remote control unit can be used from a straight distance of

approximately 23 feet/7 meters, but this distance will shorten or

operation will become difficult if there are obstacles between the

remote control unit and the remote control sensor, if the remote

control sensor is exposed to direct sunlight or other strong light, or

if operated from an angle.

• Neon signs or other devices emitting pulse-type noise nearby may

result in malfunction, so keep the set as far away from such

devices as possible.

Approx. 23 feet/7 m

30°

w Insert the R6P/AA batteries properly, as

shown on the diagram.

q Press as shown by the arrow and slide

off.

e Close the lid.

NOTES:

• Use only R6P/AA batteries for replacement.

• Be sure the polarities are correct. (See the illustration inside the battery compartment.)

• Remove the batteries if the remote control transmitter will not be used for an extended period of time.

• If batteries leak, dispose of them immediately. Avoid touching the leaked material or letting it come in contact with clothing, etc. Clean the

battery compartment thoroughly before installing new batteries.

• Have replacement batteries on hand so that the old batteries can be replaced as quickly as possible when the time comes.

• Even if less than a year has passed, replace the batteries with new ones if the set does not operate even when the remote control unit is

operated nearby the set. (The included battery is only for verifying operation. Replace it with a new battery as soon as possible.)

17

ENGLISH

10

SETTING UP THE SYSTEM

• Once all connections with other AV components have been completed as described in “CONNECTIONS” (see pages 9 to 15), make the

various settings described below on the display.

These settings are required to set up the listening room’s AV system centered around the this unit.

STATUS MUTING

T.TONE

MASTER

VOL

TITLE

DISC SKIP+

CD·MD/CDR·DVD/VDP

VIDEO SELECT

SYSTEM

SET UP MENU

RETURN DISPLAY

SURROUND

98

2

3

6

7

SELECT

CH SELECT

SYSTEM SETUP button

Press this to display the system setup on the display.

CURSOR buttons (•, ª, 0, 1)

Press this change what appears on the display.

SELECT button

Press this to switch the display.

Also use this button to complete the setting.

• System setup items and default values (set upon shipment from the factory)

System setup Default settings

Speaker

Configuration

Subwoofer Mode

Channel Level

Digital Input

Input the combination of speakers in your system and their

corresponding sizes (SMALL for regular speakers, LARGE for full-size,

full-range) to automatically set the composition of the signals output

from the speakers and the frequency response.

This adjusts the volume of the signals output from the speakers and

subwoofer for the different channels in order to obtain optimum

effects.

This assigns the digital input jacks for the different input

sources.

Input

source

Digital

Inputs

Front Sp.

Large

Center Sp. Surround Sp. Sub Woofer

Small Small Yes

Front & Subwoofer Center Surround L & R —

12 ft (3.6 m) 12 ft (3.6 m) 10 ft (3.0 m) —

Front L

Front R Center

Surround R

Subwoofer

0 dB 0 dB 0 dB 0 dB0 dB

DVD/VDP TV/DBS

COAXIAL OPTICAL-1

Delay Time

This parameter is for optimizing the timing with which the audio

signals are produced from the speakers and subwoofer according to

the listening position.

Surround L

0 dB

1

Set the slide switch to “AUDIO”.

2

Use the following buttons to set up the system:

AUDIO

CD

MD/CDR

VIDEO

This selects the subwoofer speaker for playing deep bass

signals.

Subwoofer mode = Normal

—

NOTE:

• The system setup is not displayed when “HEADPHONE ONLY” is selected.

CDR/TAPE

OPTICAL-2

18

ENGLISH

Before setting up the system

1

2

Press the SYSTEM button to enter the setting.

Check that all the components are correct, then press the POWER operation switch on the main unit or

the POWER button on the remote control unit to turn on the power.

3

Press the SELECT or (down) button to switch to the speaker configuration set up.

*SYSTEM SET UP

NOTE:

Press the SYSTEM button again to finish system set up. System set up can be finished at any time. The changes to the settings made up to

that point are entered.

NOTE: Please make sure the “AUDIO” position of the slide switch on the remote control unit.

(Main unit) (Remote control unit)

Setting the speaker configuration

1

Use the (left) and (right) buttons to select your front speaker type.

1 FRONT LARGE

LARGE

SMALL

(left) button (right) button

Press the SELECT or (down) button to switch to the center speaker setting.

2

Use the (left) and (right) buttons to select your center speaker type.

2 CENTER SMALL

LARGE

SMALL

NONE

(left) button (right) button

Press the SELECT or (down) button to switch to the surround speaker setting.

3

Use the (left) and (right) buttons to select your surround speaker type.

3 SURR. SMALL

LARGE

SMALL

NONE

(left) button (right) button

Press the SELECT or (down) button to switch to the subwoofer setting.

NOTE:

• When “Small” has been selected for the front speakers, “Large” cannot be selected for the center speaker.

(Initial)

19

ENGLISH

NOTE:

• When “Small” has been selected for the front speakers, “Large” cannot be selected for the surround speakers.

4

Use the (left) and (right) buttons to select your subwoofer setting.

4 S.WOOFER YES

YES

NO

(left) button (right) button

Press the SELECT or (down) button to enter the settings and switch to the SUBWOOFER MODE

setting.

• Parameters

Large…… Select this when using speakers that can fully reproduce low sounds of below 80 Hz.

Small…… Select this when using speakers that cannot reproduce low sounds of below 80 Hz with sufficient volume. When this setting is

selected, low frequencies of below 80 Hz are assigned to the subwoofer.

None…… Select this when no speakers are installed.

Yes/No…. Select “Yes” when a subwoofer is installed, “No” when it’s not installed.

NOTE:

Select “Large” or “Small” not according to the physical size of the speaker, but according to the bass reproduction capacity at 80 Hz. If you cannot

determine the best setting, try comparing the sound when set to “Small” and when set to “Large”, at a level that will not damage the speakers.

Caution:

In case the subwoofer is not used, be sure to set “Subwoofer = No”, or the bass sound of front channel is divided to subwoofer channel and

not reproduced in some mode.

Setting the SUBWOOFER MODE

1

Use the (left) and (right) buttons to select the Subwoofer mode.

5 SW MODE NORM

NORM +MAIN

(left) button (right) button

Press the SELECT or (down) button to enter the setting and switch to the SPEAKER DISTANCE

setting.

NOTES:

— Assignment of low frequency signal range —

• The signals produced from the subwoofer channel are LFE signals (during playback of Dolby Digital or DTS signals) and the low frequency

signal range of channels set to “SMALL” in the setup. The low frequency signal range of channels set to “LARGE” are produced from those

channels.

— Subwoofer mode —

• The subwoofer mode setting is only valid when “LARGE” is set for the front speakers and “YES” is set for the subwoofer in the “Speaker

Configuration” settings (see pages 18, 19).

If “SMALL” is set for the front speakers or “NO” is set for the subwoofer, the subwoofer mode setting does not affect playback of low

frequency signal range.

• When the “+MAIN” playback mode is selected, the low frequency signal range of channels set to “LARGE” are produced simultaneously

from those channels and the subwoofer channel.

In this playback mode, the low frequency range expand more uniformly through the room, but depending on the size and shape of the room,

interference may result in a decrease of the actual volume of the low frequency range.

• When the “NORM” playback mode is selected, the low frequency signal range of channels set to “LARGE” are only produced from those

channels. In this playback mode there tends to be little interference of the low frequency range in the room.

• Try playing the music or movie source and select the playback mode providing the stronger low frequency range sound.

(Initial)

20

ENGLISH

Setting the delay time

Input the distances from the listening position to the speakers and set the surround delay time.

Preparations:

Measure the distances from the listening position to the speakers (L1 to L3 on the diagram at the right).

L1: Distance from center speaker to listening position

L2: Distance from front speakers to listening position

L

3: Distance from surround speaker to listening position

CAUTION:

Set the center speaker at the same distance from the front speakers (left and right) or the subwoofer,

or so that the difference in distance (L2 – L1) is 5 feet or less.

Set the surround speakers (left and right) at the same distance from the front speakers (left and right)

or the subwoofer, or so that the difference in distance (L2 – L3) is 15 feet or less.

L1

L2

L3

FL

Center FR

Listening

position

SL

SR

1

Use the (left) and (right) buttons to set the distance from the front speakers and subwoofer to the

listening position.

6 FRNT/SW 12ft

• The number changes in units of 1 foot each time one of the buttons is pressed. Select the value closest

to the measured distance.

(“/SW” appears only when subwoofer = yes.)

Press the SELECT or (down) button to switch to the center speaker setting.

NOTE:

• The speaker distance can be adjusted between 0 and 60 feet in steps of 1 foot.

2

Use the (left) and (right) buttons to set the distance from the center speakers to the listening

position.

7 CENTER 12ft

• The number changes in units of 1 foot each time one of the buttons is pressed. Select the value closest

to the measured distance.

Press the SELECT or (down) button to switch to the surround speaker setting.

NOTE:

• No setting when “None” has been selected for the center speaker.

3

Use the (left) and (right) buttons to set the distance from the surround speakers to the listening

position.

8 SURR. 10ft

• The number changes in units of 1 foot each time one of the buttons is pressed. Select the value closest

to the measured distance.

Press the SELECT or (down) button to enter the setting and switch the DIGITAL input (COAX) setting.

NOTE:

• No setting when “None” has been selected for the surround speakers.

La page charge ...

Denon AVR-882 Manuel utilisateur

Denon AVR-882 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents