Uniden UCSWITCH9 Le manuel du propriétaire

Uniden
Marque
Uniden
Modèle
UCSWITCH9
Catégorie
Adaptateurs PoE
Taper
Le manuel du propriétaire

Ce manuel convient également à

© 2018 Uniden America Corporation Issue 1, May 2018
Irving, Texas
UCSWITCH5
UCSWITCH9
OWNER’S MANUAL
Uniden surveillance products are not manufactured and/or sold with the
intent to be used for illegal purposes. Uniden expects consumer’s use of
these products to be in compliance with all local, state, and federal law.
For further information on video surveillance and audio recording legal
requirements, please consult your local, state, and federal ocials.
Uniden constantly works on improving our products. This includes
updating our documentation with the latest rmware changes. Go to
www.uniden.com to nd the latest version of all documentation.
© 2018 Uniden America Corporation
All rights reserved.
CONTENTS
INTRODUCTION ................................................ 5
PACKAGE CONTENTS ................................................ 5
FRONT PANEL .................................................. 6
UCSWITCH5 .................................................................. 6
UCSWITCH9 .................................................................. 6
LED Descriptions ........................................................ 6
EXTEND MODE ........................................................... 7
RJ45 PORTS ................................................................. 7
REAR PANEL ................................................................ 8
Power Socket.............................................................. 8
Grounding Terminal .................................................... 8
Lock Hole .................................................................... 8
DEVICE INSTALLATION .................................. 8
INSTALLATION RECOMMENDATIONS ..................... 8
Anti-Static Protection .................................................. 9
Lightning Protection .................................................... 9
MOUNTING REQUIREMENTS .................................... 9
PHYSICAL CONNECTION ........................................... 9
RJ45 Port Connections ............................................... 9
Check Cabling .......................................................... 10
Connect to Power Supply ......................................... 10
TECHNICAL SPECIFICATIONS ..................... 10
FCC PART 15/IC COMPLIANCE .................... 12
ONE-YEAR LIMITED WARRANTY ................ 13
5
UCSWITCH5/UCSWITCH9
OWNER’S MANUAL
INTRODUCTION
UCSWITCH5 and UCSWITCH9 are 10/100Mbps PoE switches. They
provide 5/9 10/100Mbps auto-negotiation RJ45 ports, in which ports
1-4/8 support IEEE 802.3af PoE (15.4W) and IEEE 802.3at PoE+ (30W).
The whole PoE power output is 58W/120W. With Cat 5 Ethernet cable,
power and data can be simultaneously transmitted to APs, IP cameras, IP
phones, and other Power Devices).
In addition, UCSWITCH5 and UCSWITCH9 support Extend mode. With
enabling Extend mode and Cat 5e Ethernet cable, the transmission
distance of data and power can be up to 250m.
PACKAGE CONTENTS
Open your package and check the following:
ITEM QUANTITY
UCSWITCH5 or
UCSWITCH9
1
Power Adapter 1
Foot Pads 4
User Manual 1
Screws 8
Wall anchors (UCSWITCH5
only)
2
If any item is incorrect, missing, or damaged, please keep the original
package and contact the www.uniden.com for replacement immediately.
6
FRONT PANEL
UCSWITCH5
UCSWITCH9
LED Descriptions
LED STATUS DESCRIPTION
PWR
Solid The device is properly connected to the power
supply.
O The device is not connected properly to the
power supply.
POE-
MAX
Solid The PoE power reaches alarm status; the
avalable PoE power is less than 6W.
Blinking PoE power is at maximum.
O PoE power is working properly; the available
PoE power is more than 6W
LINK/
ACT
Solid The corresponding port is connected properly.
Blinking The corresponding port is transmitting data.
O The corresponding port is not connected or
connected improperly.
7
LED STATUS DESCRIPTION
POE
STATUS
Solid The corresponding port is connected to a
Powered Device (PD) and powers the PD
properly.
Blinking The corresponding port’s PoE output exceeds
30W.
O The corresponding port has no PoE power
output or no PD is connected.
N/A O Reserved
EXTEND MODE
If Extend mode is enabled:
MODEL STATUS DESCRIPTION
UCSWITCH5
O Ports 1 - 4: 100M
On Ports 1 - 4: 10M
UCSWITCH9
O Ports 1 - 8: 100M
On Ports 1 - 8: 10M
To guarantee Extend mode performance, use a
Cat 5e or better Ethernet cable and congure the
remote device’s speed and duplex to be “Auto
Negotiation.”
If Extend mode is disabled, the transmission
distance of PoE powering and data is up to 150m if
using a Cat 5e or better Ethernet cable.
RJ45 PORTS
MODEL 10/100 MBPS
RJ45 PORTS
UPLINK PORT
UCSWITCH5 4 1
UCSWITCH9 8 1
8
REAR PANEL
The rear panel comprises a power socket and a grounding terminal.
UCSWITCH9 also had a lock hole.
Power Socket
The included power adapter connects the device to power through the
power socket.
Grounding Terminal
If desired, connect a grounding cable (not included) for lightning electrical
discharge protection.
Lock Hole
(UCSWITCH9 only) If the UCSWITCH9 is installed in a high trac area,
use a laptop lock (not included) in the lock hole to prevent tampering.
DEVICE INSTALLATION
INSTALLATION RECOMMENDATIONS
Follow these recommendations to ensure your safety and your device’s
operation:
• Wear antistatic gloves while installing and connect the device to
power.
• Use the included power adapter to power the device.
• Make sure the input voltage matches the value which is marked on the
device’s label.
• Place the device in a well-ventilated and dry environment.
• Do not open the device case.
9
There is a seal covering one of the screws in the
device case. If the device needs repair, keep the seal
unbroken until a Uniden technician can make the repair.
The user should not break the seal covering the screw.
If the seal is broken, the userwill be responsible for any
damage.
• Disconnect the device from the power supply when cleaning it.
• Position the device away from strong electrical currents.
Anti-Static Protection
Dust may lead to electrostatic buildup. Keep the device and its
environment clean. (A regular dusting is necessary.)
Lightning Protection
In a thunderstorm, the electrical discharge from lightning may damage
the device. Make sure the device, the installation location, and power
outlet on the wall are well-grounded.
MOUNTING REQUIREMENTS
Read and follow these requirements:
• The mounting location is stable and sturdy.
• Place the device where required in a clean, dry, and well-ventilated
environment. Keep at least 4 in.(10cm.) free on all sides for cooling.
• Do not place any heavy or large object on the device.
• Paste the four foot pad stickers on the corresponding four corners of
the underside of the device
PHYSICAL CONNECTION
RJ45 Port Connections
The RJ45 port uses an Ethernet cable to connect the switch to remote
devices. Ports 1 - 4/8 support IEEE 802.3af and IEEE 802.3at PoE
supply. The PD can be wireless AP, IP phone or IP camera, etc.
10
IP Phone IP Camera
Router
RJ45 Connection Examples
UCSWITCH-9
NOTES:
• A Cat 5e or better Ethernet cable is recommended. As each RJ45 port
supports MDI/MDIX auto-negotiating, either parallel or crossover cable
is acceptable.
• The device supports dynamic PoE supply; it will power the PD
properly and automatically.
Check Cabling
Once installation is completed, check the device cabling as follows:
• The operating power supply should agree with rated input standard.
• Ports cables are connected correctly.
• If there is outdoor cabling, connect a lightning protector to the cable
before you plug the cable into the port.
Connect to Power Supply
1. Plug the power adapter into the power socket.
2. Plug the other end of the power adapter into DC power.
3. The PWR LED turns on.
TECHNICAL SPECIFICATIONS
UCSWITCH5 UCSWITCH9
INTERFACES
10/100MBPS RJ45 5 9
11
UCSWITCH5 UCSWITCH9
High Priority Ports Port 1 Ports 1 - 2
PERFORMANCE
Store-and-Forward Supported
MAC Table 1k 4k
MAC Learning Auto-learning/auto-aging
Switching Capacity 1Gbps 1.8Gbps
PoE POWER
PoE Standard IEEE 802.3af, IEEE 802.3at
PoE Powering
Mode
Supports 8 pins powering; Pins 1, 2, 3,
and 6 and pins 4, 5, 7, and 8 can power
simultaneously.
PoE Port 1 - 4 1 - 8
Max Port Output 30W 30W
Max Total Output 58W 120W
Extend Mode
Supported
LIGHTNING-PROOF RANKING
RJ45 Port
Lightning Proof
4KV
Power Source
Lightning Proof
4KV 2KV
Power Input 51V DC, 1.25A 51V DC, 2.5A
PHYSICAL ENVIRONMENT
Operating
Environment
Temperature: 32ºF - 104ºF
(0ºC - 40ºC)
Humidity: 10% - 90%
RH Non-Condensing
12
UCSWITCH5 UCSWITCH9
Storage
Environment
Temperature: -40ºF - 158ºF
(-40ºC - 70ºC)
Humidity: 5% - 90%
RH Non-Condensing
TRANSMISSION SPEED
Ethernet 10Mbps Half Duplex
20Mbps Full Duplex
Fast Internet 100Mbps Half Duplex
200Mbps Full Duplex
TRANSMISSION MEDIUM
Ethernet CAT 3 or better UTP/STP
Fast Internet CAT 5 or better UTP/STP
NETWORK STANDARD
IEEE 802.3, IEEE 802.3u, IEEE802.3af,
IEEE802.3at, IEEE802.3x
FCC Part 15/IC COMPLIANCE
FCC Compliance
This device complies with Part 15 of the FCC rules. Operation is subject
to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Changes or modications not expressly approved by the party
responsible for compliance could void your authority to operate the
equipment.
Avis de conformité à la FCC : Ce dispositif a été testé et s’avère
conforme à l’article 15 des règlements de la Commission fédérale
des communications (FCC). Ce dispositif est soumis aux conditions
suivantes: 1) Ce dispositif ne doit pas causer d’interférences nuisibles et;
2) Il doit pouvoir supporter les parasites qu’il reçoit, incluant les parasites
pouvant nuire à son fonctionnement.
13
Tout changement ou modication non approuvé expressément par
la partie responsable pourrait annuler le droit à l’utilisateur de faire
fonctionner cet équipement.
IC Compliance
This device complies with Industry Canada license-exempt RSS
standard(s). Operation is subject to the following two conditions: (1) this
device may not cause interference, and (2) this device must accept any
interference, including interference that may cause undesired operation
of the device.
Changes or modications not expressly approved by the party
responsible for compliance could void your authority to operate the
equipment.
Cet appareil est conforme aux normes RSS exemptes de licences
d’Industrie Canada. Son fonctionnement est soumis aux deux conditions
suivantes : (1) cet appareil ne doit pas causer d’interférences nuisibles et
(2), il doit pouvoir accepter les interférences, incluant celles pouvant nuire
à son fonctionnement normal.
Tout changement ou modication non approuvé expressément par
la partie responsable pourrait annuler le droit à l’utilisateur de faire
fonctionner cet équipement.
ONE-YEAR LIMITED WARRANTY
Important: SAVE YOUR RECEIPT! Evidence of original purchase is
required for warranty service.
WARRANTOR: Uniden America Corporation (“Uniden”) ELEMENTS OF
WARRANTY: Uniden warrants, for one year, to the original retail owner,
this Uniden Product to be free from defects in materials & craftsmanship
with only the limitations or exclusions set out below.
WARRANTY DURATION: This warranty to the original user shall
terminate & be of no further eect 12 months after the date of original
retail sale. The warranty is invalid if the Product is (A) damaged or not
maintained as reasonable or necessary, (B) modied, altered, or used
as part of any conversion kits, subassemblies, or any congurations
not sold by Uniden, (C) improperly installed, (D) serviced or repaired by
14
someone other than an authorized Uniden service center for a defect or
malfunction covered by this warranty, (E) used in any conjunction with
equipment or parts or as part of any system not manufactured by Uniden,
or (F) installed or programmed by anyone other than as detailed by the
owner’s manual for this product.
STATEMENT OF REMEDY: In the event that the product does not
conform to this warranty at any time while this warranty is in eect,
warrantor will either, at its option, repair or replace the defective unit &
return it to you without charge for parts, service, or any other cost (except
shipping & handling) incurred by warrantor or its representatives in
connection with the performance of this warranty. Warrantor, at its option,
may replace the unit with a new or refurbished unit.
THE LIMITED WARRANTY SET FORTH ABOVE IS THE SOLE &
ENTIRE WARRANTY PERTAINING TO THE PRODUCT & IS IN LIEU
OF & EXCLUDES ALL OTHER WARRANTIES OF ANY NATURE
WHATSOEVER, WHETHER EXPRESS, IMPLIED OR ARISING BY
OPERATION OF LAW, INCLUDING, BUT NOT LIMITED TO ANY
IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR
A PARTICULAR PURPOSE. THIS WARRANTY DOES NOT COVER
OR PROVIDE FOR THE REIMBURSEMENT OR PAYMENT OF
INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some states do not
allow this exclusion or limitation of incidental or consequential damages
so the above limitation or exclusion may not apply to you.
LEGAL REMEDIES: This warranty gives you specic legal rights, & you
may also have other rights which vary from state to state. This warranty is
void outside the United States of America & Canada.
PROCEDURE FOR OBTAINING PERFORMANCE OF WARRANTY:
If, after following the instructions in the owner’s manual you are certain
that the Product is defective, pack the Product carefully (preferably in its
original packaging). The Product should include all parts & accessories
15
originally packaged with the Product. Include evidence of original
purchase & a note describing the defect that has caused you to return it.
The Product should be shipped freight prepaid, by traceable means, to
warrantor at:
Uniden America Service
C/O Saddle Creek
743 Henrietta Creek Rd., Suite 100
Roanoke, TX 76026
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16

Uniden UCSWITCH9 Le manuel du propriétaire

Uniden
Marque
Uniden
Modèle
UCSWITCH9
Catégorie
Adaptateurs PoE
Taper
Le manuel du propriétaire
Ce manuel convient également à
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes

Autres documents