Ryobi RY142300 Le manuel du propriétaire

Catégorie
Nettoyeurs haute pression
Taper
Le manuel du propriétaire

Ce manuel convient également à

OPERATOR’S MANUAL
MANUEL D’UTILISATION
MANUAL DEL OPERADOR
ELECTRIC PRESSURE WASHER
LAVEUSE À PRESSION À ÉLECTRIQUE
LAVADORA DE PRESIÓN A ELÉCTRICA
RY142300/RY142300VN/
RY142300VNM
WARNING: To reduce the risk of
injury, the user must read and understand
the operator’s manual before using this
product.
TABLE OF CONTENTS
Important Safety Instructions ............... 2
Specific Safety Rules ........................3-4
Symbols .............................................5-6
Electrical ............................................... 7
Features ................................................8
Assembly .........................................8-10
Operation .......................................10-14
Maintenance ..................................14-15
Troubleshooting .................................16
Parts Ordering and Service .. Back Page
AVERTISSEMENT : Pour
réduire les risques de blessures,
l’utilisateur doit lire et veiller à bien
comprendre le manuel d’utilisation avant
d’employer ce produit.
TABLE DES MATIÈRES
Instructions importantes
concernant la sécurité.......................... 2
Règles de sécurité particulières ........3-4
Symboles ...........................................5-6
Caractéristiques électriques ..............6-7
Caractéristiques ................................... 8
Assemblage .....................................8-10
Utilisation .......................................10-14
Entretien ........................................14-15
Dépannage ......................................... 16
Commande de pièces et
réparation ............................ Páge arrière
ADVERTENCIA: Para reducir
el riesgo de lesiones, el usuario debe leer
y comprender el manual del operador
antes de usar este producto.
ÍNDICE DE CONTENIDO
Instrucciones de seguridad
importantes .......................................... 2
Reglas de seguridad específicas ......3-4
Símbolos ...........................................5-6
Aspectos eléctricos ........................... 6-7
Características ..................................... 8
Armado ............................................ 8-10
Funcionamiento .............................10-14
Mantenimiento ...............................14-15
Solución de problemas ...................... 16
Pedidos de piezas y
servicio .............................Pág. posterior
SAVE THIS MANUAL FOR
FUTURE REFERENCE
CONSERVER CE MANUEL
POUR FUTURE RÉFÉRENCE
GUARDE ESTE MANUAL
PARA FUTURAS CONSULTAS
ii
See this fold-out section for all of the figures
referenced in the operator’s manual.
Consulter l’encart à volets afin d’examiner toutes les
figures mentionnées dans le manuel d’utilisation.
Consulte esta sección desplegable para ver todas
las figuras a las que se hace referencia
en el manual del operador.
iii
Fig. 1
Fig. 2
A - Test button (bouton de test, botón de prueba)
B - Reset button (bouton de réinitialisation,
botón de reajuste)
A
B
A
B
C
Fig. 3
A - On/off switch (commutateur marche / arrêt, interruptor de encendido)
B - Nozzle storage (rangement de buses, almacenamiento para boquilla)
C - Spray wand (lance de pulvérisation, tubo rociado)
D - Motor (moteur, motor)
E - Soap tank (réservoir de savon, tanque de jabón)
C
H
F
D
E
A
G
F - Trigger with lock-out (gâchette avec verouillage, gatillo con seguro)
G - Power cord storage bracket (support de rangement pour cordon
d’alimentation, soporte para almacenamiento del cordón eléctrico)
H - Trigger handle (poignée de gâchete, mango del gatillo)
I - High pressure hose (tuyau haute pression, manguera de alta presión)
I
B
A - Pressure washer power cord
(cordon d’alimentation de la
laveuse à pression, cordón
de corriente de la lavadora de
presión)
B - Drip loop (boucle
d’égouttement, vuelta de goteo)
C - Extension cord (cordon
prolongateurs, cordón de
extensión)
iv
Fig. 4
Fig. 5
Fig. 6
A - Button (bouton, botón)
B - Push to insert (pousser pour insérer,
presione para insertar)
Fig. 7
B
B
A
Fig. 8
Fig. 9
A - Trigger handle (poignée à gâchette, mango
del gatillo)
B - Spray wand (poignée à gâchette, tubo
rociador)
A
B
Fig. 10
A - Collar (collier, casquillo)
B - Inlet coupler (raccord d’entrée, acoplador de
entrada)
C - High pressure hose (tuyau haute pression,
manguera de alta presión)
A
B
C
A - Threaded outlet (têton fileté, conexión
roscada)
B - Collar (collier, casquillo)
C - High-pressure hose (flexible haute pression,
manguera de alta presión)
A
B
C
A
B
A - Water intake (rise d’eau, entrada de agua)
B - Garden hose (tuyau d’arrosage, manguera de
jardín)
A - On/off switch (commutateur marche / arrêt,
interruptor de encendido/apagado)
A
A - Trigger (gâchette, gatillo)
B - Lock-out (verrouillage, seguro)
A
B
A - Spray wand (lance de pulvérisation, tubo
rociador)
B - Nozzle (buse, boquilla)
C - Turbo nozzle (buse de turbo, boquilla de
turbo)
D - Pull back the quick-connect collar (tirer la
bague à connexion rapide, tire del collar de
conexión rápida)
E - Push the nozzle into place (insérer en place
la buse, introduzca la boquilla en su lugar)
F - Push the collar forward (poussez en avant la
bague, empuje del collar adelante)
A
B
C
D
D
E
E
F
F
Fig. 11
v
TO MOVE THE MACHINE
DÉPLACEMENT DE LA MACHINE
PARA MOVER LA MÁQUINA
Fig. 13
Fig. 12
Fig. 14
Fig. 15
A - Power cord (cordon d’alimentation, cordón
de corriente)
B - Power cord storage bracket (support de
rangement pour cordon d’alimentation,
soporte para almacenamiento del cordón
eléctrico)
A
B
Fig. 17
Fig. 16
A - Straightened paper clip (trombone droit, clip
para papel abierto)
B - Nozzle (embout, boquilla)
A
B
Fig. 18
A - Cap (capuchon, tapa)
B - Detergent (détergente, detergente)
C - Soap tank (réservoir de savon, tanque de
jabón)
A
B
C
Fig. 19
A - Threaded top (bouchon vissé, parte superior
roscada)
B - Rubber seal (joint de caoutchouc, sello de
goma)
C - Paper seal (sceaux de papier, sello de papel)
D - Water intake (rise d’eau, entrada de agua)
E - Pump outlet (sortie de la pompe, orificio de
descarga de la bomba)
F - Pump protector (protecteur de pompe,
protector de bomba)
C
B
A
A
D
TO STORE THE MACHINE
REMISAGE DE LA MACHINE
PARA GUARDAR LA MÁQUINA
E
F
2 — English
WARNING:
Read and understand all instructions. Failure to follow
all instructions listed below may result in electric shock,
fire, and/or serious personal injury.
WARNING:
When using this product basic precautions should always
be followed, including the following:
READ ALL INSTRUCTIONS BEFORE USING
THIS PRODUCT
To reduce the risk of injury, close supervision is neces-
sary when a product is used near children.
Be thoroughly familiar with controls. Know how to stop
the product and release pressure quickly.
Stay alert and exercise control. Watch what you are
doing and use common sense. Do not operate product
when you are tired. Do not rush.
Do not operate the product while under the influence
of drugs, alcohol, or any medication.
Keep the area of operation clear of all persons,
particularly small children, and pets.
Don’t overreach or stand on a ladder, rooftop, or other
unstable support. Keep proper footing and balance at
all times.
Follow the maintenance instructions specified in this
manual.
This product is provided with a ground fault circuit
interrupter built into the power cord plug. If replace-
ment of the plug or cord is needed, use only identical
replacement parts.
WARNING: Risk of injection or injury – Do not direct
discharge stream at persons.
SAVE THESE INSTRUCTIONS
GROUNDING INSTRUCTIONS
This product must be grounded. If it should malfunction or
breakdown, grounding provides a path of least resistance for
electric current to reduce the risk of electric shock. This prod-
uct is equipped with a cord having an equipment-grounding
conductor and a grounding plug. The plug must be plugged
into an appropriate outlet that is properly installed and
grounded in accordance with all local codes and ordinances.
DANGER: Improper connection of the equipment-grounding
conductor can result in a risk of electrocution. Check with a
qualified electrician or service personnel if you are in doubt
as to whether the outlet is properly grounded. Do not modify
the plug provided with the product – if it will not fit the outlet,
have a proper outlet installed by a qualified electrician. Do
not use any type of adaptor with this product.
GROUND FAULT CIRCUIT INTERRUPTER
PROTECTION
This pressure washer is provided with a ground-fault circuit-
interrupter (GFCI) built into the plug of the power supply
cord. This device provides additional protection from the risk
of electric shock. Should replacement of the plug or cord
become necessary, use only identical replacement parts that
include GFCI protection.
EXTENSION CORDS
See Figure 1.
Use only 3-wire extension cords that have 3-prong grounding-
type plugs and 3-pole cord connectors that accept the plug
from the product. Use only extension cords that are intended
for outdoor use. These extension cords are identified by a
marking "Acceptable for use with outdoor appliances; store
indoors while not in use." Use only extension cords having
an electrical rating not less than the rating of the product. Do
not use damaged extension cords. Examine extension cord
before using and replace if damaged. Do not abuse exten-
sion cord and do not yank on any cord to disconnect. Keep
cord away from heat and sharp edges. Always disconnect
the extension cord from the receptacle before disconnecting
the product from the extension cord.
WARNING: To reduce the risk of electrocution, keep all
connections dry and off the ground. Do not touch plug with
wet hands.
To avoid the possibility of the product plug or outlet getting
wet, the operator should arrange a “drip loop” in the cord
connecting the product to the outlet. The “drip loop” is that
part of the cord below the level of the outlet, or the connector
if an extension cord is used, to prevent water traveling along
the cord and coming in contact with the outlet.
IMPORTANT SAFETY INSTRUCTIONS
3 — English
Use caution when positioning the pressure washer
for use. Warm air from the motor could cause discolored
spots on grass.
Know your product. Read the operator’s manual care-
fully. Learn the machine’s applications and limitations
as well as the specific potential hazards related to this
product.
To reduce the risk of injury, keep children and visitors
away. All visitors should wear safety glasses and be kept
a safe distance from work area.
Use right product. Don’t force product or attachment to
do a job it was not designed for. Don’t use it for a purpose
not intended.
Dress properly. Wear long pants and long sleeves. Do
not wear loose clothing, neckties, or jewelry. They can get
caught and draw you into moving parts. Rubber gloves
and nonskid footwear are recommended when working
outdoors. Also wear protective hair covering to contain
long hair.
Do not operate the equipment while barefoot or when
wearing sandals or similar lightweight footwear. Wear
protective footwear that will protect your feet and improve
your footing on slippery surfaces.
Exercise caution to avoid slipping or falling.
Alwaysweareyeprotectionwithsideshieldsmarked
to comply with ANSI Z87.1. Following this rule will re-
duce the risk of serious personal injury.
Use only recommended accessories. The use of im-
proper accessories may cause risk of injury.
Check damaged parts. Before further use of the product,
a guard or other part that is damaged should be care-
fully checked to determine that it will operate properly
and perform its intended function. Check for alignment
of moving parts, binding of moving parts, breakage of
parts, mounting, and any other conditions that may af-
fect its operation. A guard or other part that is damaged
must be properly repaired or replaced by an authorized
service center to avoid risk of personal injury.
Never leave product running unattended. Turn power
off. Don’t leave product until it comes to a complete stop.
Keep the motor free of grass, leaves, or grease to
reduce the chance of a fire hazard.
Follow manufacturer’s recommendations for safe
loading, unloading, transport, and storage of machine.
Keep product dry, clean, and free from oil and grease.
Always use a clean cloth when cleaning. Never use brake
fluids, gasoline, petroleum-based products, or any sol-
vents to clean product.
Check the work area before each use. Remove all
objects such as rocks, broken glass, nails, wire, or string
which can be thrown or become entangled in the
machine.
Do not use product if switch does not turn it off. Have
switch replaced by an authorized service center.
Avoid dangerous environment. Don’t expose to rain.
Keep work area well lit.
Do not abuse the cord. Never use the cord to carry the
product or to disconnect the plug from an outlet. Keep
cord away from heat, oil, sharp edges, or moving parts.
Replace damaged cords immediately. Damaged cords
increase the risk of electric shock.
Ground Fault Circuit Interrupter (GFCI) protection
should be provided on the circuit(s) or outlet(s) to be
used for the product. Receptacles are available having
built-in GFCI protection and may be used for this measure
of safety.
This pressure washer is not recommended for use
with an extension cord. If an extension cord must be
used, please make sure it is in good condition. When
using an extension cord, be sure to use one heavy enough
to carry the current your product will draw. A wire gauge
size (A.W.G.) of at least 12 is recommended for an ex-
tension cord 25 feet or less in length. If in doubt, use the
next heavier gauge. The smaller the gauge number, the
heavier the cord. An undersized cord will cause a drop in
line voltage resulting in loss of power and overheating.
WARNING: Use outdoor extension cords marked SW-A,
SOW-A, STW-A, STOW-A, SJW-A, SJTW-A, or SJTOWA.
These cords are rated for outdoor use and reduce the risk
of electric shock.
Inspect extension cords periodically and replace if
damaged. Keep handles dry, clean, and free from oil or
grease.
Never direct a water stream toward people or pets,
or any electrical device.
Before starting any cleaning operation, close doors
and windows. Clear the area to be cleaned of debris,
toys, outdoor furniture, or other objects that could create
a hazard.
Do not use acids, alkalines, solvents, flammable ma-
terial, bleaches, or industrial grade solutions in this
product. These products can cause physical injuries to
the operator and irreversible damage to the machine.
WARNING: High pressure jets can be dangerous if
subject to misuse. The jet must not be directed at per-
sons, animals, electrical devices, or the machine itself.
Keep the motor away from flammables and other
hazardous materials.
Check bolts and nuts for looseness before each use. A
loose bolt or nut may cause serious motor problems.
Before storing, allow the motor to cool.
When servicing use only identical replacement parts.
Use of any other parts may create a hazard or cause
product damage.
SPECIFIC SAFETY RULES
4 — English
Ensure the high pressure hose is properly connected
before using the product.
Connect pressure washer only to an individual branch
circuit.
Hold the trigger handle securely with both hands. Ex-
pect the trigger handle to move when the trigger is pulled
due to reaction forces. Failure to do so could cause loss
of control and injury to yourself and others.
For outdoor use only.
Save these instructions. Refer to them frequently and
use them to instruct other users. If you loan someone this
product, loan them these instructions also.
ONLY use cold water.
Never pick up or carry the machine while the motor
is running.
Never start the machine if ice has formed in any part of
the equipment.
Make sure minimum clearance of 3 feet is maintained
from combustible materials.
Never spray close to the surface to be cleaned, as you
can damage the surface.
After stopping the motor, always pull the trigger on the
trigger handle to relieve stored pressure in the high
pressure hose. Failure to do so could result in serious
personal injury.
SPECIFIC SAFETY RULES
5 — English
Some of the following symbols may be used on this product. Please study them and learn their meaning. Proper
interpretation of these symbols will allow you to operate the product better and safer.
SYMBOL NAME DESIGNATION/EXPLANATION
Safety Alert Indicates a potential personal injury hazard.
Read Operator’s Manual
To reduce the risk of injury, user must read and understand
operator’s manual before using this product.
Eye Protection
Always wear eye protection with side shields marked to comply
with ANSI Z87.1.
Wet Conditions Alert
Do not expose to rain or use in damp locations, and never direct
a water stream toward any electrical device.
Risk of Injection
To reduce the risk of injection or injury, never direct a water stream
towards people or pets or place any body part in the stream. Leak-
ing hoses and fittings are also capable of causing injection injury.
Do not hold hoses or fittings.
Risk of Explosion
Do not spray flammable liquids. Flammable liquids and their vapors
are explosive and can cause severe burns or death.
Kickback
To reduce the risk of injury from kickback, hold the spray wand
securely with both hands when the machine is on.
Electric Shock Do not use near electric power lines or receptacle outlets.
Chemical Burns
To reduce the risk of injury or damage, DO NOT USE ACIDS,
ALKALINES, BLEACHES, SOLVENTS, FLAMMABLE MATERIAL,
OR INDUSTRIAL GRADE SOLUTIONS in this product.
The following signal words and meanings are intended to explain the levels of risk associated with this product.
SYMBOL SIGNAL MEANING
DANGER:
Indicates a hazardous situation, which, if not avoided, will result in death or
serious injury.
WARNING:
Indicates a hazardous situation, which, if not avoided, could result in death or
serious injury.
CAUTION:
Indicates a hazardous situation, that, if not avoided, may result in minor or
moderate injury.
NOTICE:
(Without Safety Alert Symbol) Indicates information considered important, but
not related to a potential injury (e.g. messages relating to property damage).
SYMBOLS
6 — English
Some of the following symbols may be used on this product. Please study them and learn their meaning. Proper
interpretation of these symbols will allow you to operate the product better and safer.
SYMBOL NAME DESIGNATION/EXPLANATION
V Volts Voltage
A Amperes Current
Hz Hertz Frequency (cycles per second)
W Watt Power
Alternating Current Type of current
n
o
No Load Speed Rotational speed, at no load
.../min Per Minute Revolutions, strokes, surface speed, orbits etc., per minute
SYMBOLS
7 — English
GROUNDING INSTRUCTIONS
This product must be grounded. In the event of a malfunction
or breakdown, grounding provides a path of least resistance
for electric current to reduce the risk of electric shock.
This product is equipped with an electric cord having an
equipment-grounding conductor and a grounding plug. The
plug must be plugged into a matching outlet that is properly
installed and grounded in accordance with all local codes
and ordinances.
Do not modify the plug provided. If it will not fit the outlet,
have the proper outlet installed by a qualified electrician.
WARNING:
Improper installation of a grounded plug increase the
risk of electric shock. When repair or replacement of the
cord or plug is required, take the tool to an authorized
service center.
Check with a qualified electrician or service personnel if the
grounding instructions are not completely understood, or if
in doubt as to whether the product is properly grounded.
Repair or replace a damaged or worn cord immediately.
This product is for use on a nominal 120 V circuit and has a
grounding plug similar to the plug illustrated in figure 2. Only
connect the product to an outlet having the same configura-
tion as the plug. Do not use an adapter with this product.
GROUND FAULT CIRCUIT INTERRUPTER
See Figure 2.
This unit is equipped with a Ground Fault Circuit Interrupter
(GFCI), which guards against the hazards of ground fault
currents. An example of ground fault current is the current
that would flow through a person who is using an appliance
with faulty insulation and, at the same time, is in contact
with an electrical ground such as a plumbing fixture, wet
floor, or earth.
GFCI plugs do not protect against short circuits, overloads,
or shocks.
NOTE: To ensure readiness for use, press the reset button
each time you connect the pressure washer to the power
supply.
The GFCI plug can be tested with the TEST and RESET
buttons.
To test:
Press the TEST button. You will hear a “click” sound and
the LED light will go out.
To restore power, press the RESET button. The LED light
will illuminate to indicate power has been restored.
Perform this test monthly to ensure proper operation of the
GFCI.
To reduce the risk of electric shock the supervi-
sory circuit must be operated before an appliance is
plugged into any receptacle on the device.
EXTENSION CORDS
When using a power tool at a considerable distance from
a power source, be sure to use an extension cord that has
the capacity to handle the current the product will draw. An
undersized cord will cause a drop in line voltage, possibly
resulting in overheating, loss of power, and/or circuit
breaker or GFCI tripping. Use the chart to determine the
minimum wire size required in an extension cord. Only round
jacketed cords listed by Underwriter’s Laboratories (UL)
should be used.
When working outdoors with a product, use an extension
cord that is designed for outside use. This type of cord is
designated with “WA” or “W” on the cord’s jacket.
Before using any extension cord, inspect it for loose or
exposed wires and cut or worn insulation.
It is possible to tie the extension cord and power cord in a
knot to prevent them from becoming disconnected during
use. Make a knot, then connect the plug end of the power
cord into the receptacle end of the extension cord. This
method can also be used to tie two extension cords together.
NOTE: This pressure washer is not recommended for
use with an extension cord. If using an extension cord,
arrange a drip loop to avoid the possibility of the tool
plug getting wet (see page 2).
USE ONLY THIS SIZE EXTENSION CORD WHEN USING
THIS PRODUCT:
Cord Length Wire Size (A.W.G.)
25 ft. 12
50 ft. Not Allowed
NOTE: A.W.G. = American Wire Gauge
WARNING:
Keep the extension cord clear of the working area.
Position the cord so that it will not get caught on
lumber, tools, or other obstructions while you are working
with a power tool. Failure to do so can result in serious
personal injury.
WARNING:
Check extension cords before each use. If damaged
replace immediately. Never use the product with a
damaged cord since touching the damaged area could
cause electrical shock resulting in serious injury.
ELECTRICAL CONNECTION
This product has a precision-built electric motor. It should be
connected to a power supply that is nominal 120V/60Hz
AC (typical U.S. household circuit). Do not operate this
product on direct current (DC). A substantial voltage drop
will cause a loss of power and the motor will overheat. If
the product does not operate when plugged into an outlet,
double-check the power supply.
ELECTRICAL
8 — English
UNPACKING
This product requires assembly.
Carefully remove the product and any accessories from
the box. Make sure that all items listed in the packing list
are included.
WARNING:
Do not use this product if any parts on the Packing List
are already assembled to your product when you unpack
it. Parts on this list are not assembled to the product by
the manufacturer and require customer installation. Use
of a product that may have been improperly assembled
could result in serious personal injury.
Inspect the product carefully to make sure no breakage
or damage occurred during shipping.
PRODUCT SPECIFICATIONS
Maximum Pounds Per Square Inch* ......................................................................................................................... 2,300 psi
Maximum Gallons Per Minute ....................................................................................................................................1.2 GPM
Input ............................................................................................................................nominal 120V/60Hz AC only, 13 Amps
*Max. rating determined by PWMA Standard PW101
KNOW YOUR PRESSURE WASHER
See Figure 3.
The safe use of this product requires an understanding of
the information on the product and in this operator’s manual
as well as a knowledge of the project you are attempting.
Before use of this product, familiarize yourself with all op-
erating features and safety rules.
AUTOMATIC SOAP INJECTION SYSTEM
Pour pressure washer detergent into the soap tank to apply
detergent quickly and easily to your cleaning project. Use
of the soap nozzle will activate the soap injector at a 20:1
dilution ratio.
GFCI PLUG
The pressure washer is equipped with a GFCI plug to guard
against the hazards of ground fault currents. This plug does
not protect against short circuits, overloads, or shocks.
ON/OFF SWITCH
This switch turns the pressure washer on and off.
POWER CORD STORAGE BRACKET
Store the power cord on the convenient storage bracket
when the pressure washer is not in use. Easily secure and
release with the attached bungee cord.
TRIGGER HANDLE
The trigger handle has a gripping surface that provides
added control of the spray wand and helps reduce fatigue.
TRIGGER WITH LOCK-OUT
Pulling the trigger releases a stream of water for high pres-
sure cleaning. The lock-out provides protection against
unauthorized use.
Do not discard the packing material until you have care-
fully inspected and satisfactorily operated the product.
If any parts are damaged or missing, please call
1-800-860-4050 for assistance.
PACKING LIST
Electric Pressure Washer
Handle
Trigger Handle
Spray Wand
25 ft. High Pressure Hose
Nozzles (15º, Turbo, Soap)
Operator’s Manual
FEATURES
ASSEMBLY
9 — English
WARNING:
If any parts are damaged or missing do not operate this
product until the parts are replaced. Use of this product
with damaged or missing parts could result in serious
personal injury.
WARNING:
Do not attempt to modify this product or create acces-
sories not recommended for use with this product. Any
such alteration or modification is misuse and could result
in a hazardous condition leading to possible serious
personal injury.
WARNING:
Do not connect to power supply until assembly is com-
plete. Failure to comply could result in accidental starting
and possible serious personal injury.
INSTALLING THE HANDLE
See Figure 4.
CAUTION:
Be careful to avoid pinching your fingers or hands when
installing the handle onto the frame.
Push and hold the push-pin button on the side of the handle
as you slide the handle onto the frame.
NOTE: Before use, pull the handle up until the lock button
snaps through the locking slots to secure the handle in place.
CONNECTING THE SPRAY WAND TO THE
TRIGGER HANDLE
See Figure 5.
Place the threaded end of the spray wand in the connec-
tor on the end of the trigger handle.
Turn the connector until it stops to secure the spray wand
in place.
CONNECTING THE HIGH PRESSURE HOSE
TO THE TRIGGER HANDLE
See Figure 6.
Remove the high pressure hose from the hose reel.
Screw the collar on the high pressure hose onto the trigger
handle inlet coupler by turning the hose collar clockwise.
Tighten securely.
NOTE: Be careful to avoid cross-threading, which can
cause the trigger handle to leak during use.
Pull on the hose to be certain it is properly secured.
CONNECTING THE HIGH PRESSURE HOSE
TO THE PUMP
See Figure 7.
Completely uncoil and straighten the high pressure hose
to prevent kinks.
NOTE: See Using the High Pressure Hose in
Operation
for more information about using the high pressure hose.
Align the collar on the hose to the threaded outlet on the
pump.
Install the high pressure hose collar onto the threaded
outlet.
Turn the collar clockwise to tighten the hose securely to
the pump.
NOTE: Be careful to avoid cross-threading, which can
cause the hose to leak during use.
Pull on the hose to be certain it is properly secured.
CONNECTING THE GARDEN HOSE TO THE
PRESSURE WASHER
See Figure 8.
NOTICE:
Always observe all local regulations when connecting
hoses to the water main. Some areas have restrictions
against connecting directly to public drinking water sup-
ply to prevent the feedback of chemicals into the drinking
water supply. Direct connection through a receiver tank
or backflow preventer is usually permitted.
ASSEMBLY
10 — English
WARNING:
Do not allow familiarity with the product to make you care-
less. Remember that a careless fraction of a second is
sufficient to inflict serious injury.
WARNING:
Always wear eye protection with side shields marked to
comply with ANSI Z87.1. Failure to do so could result in
objects being thrown into your eyes resulting in possible
serious injury.
WARNING:
Do not use any attachments or accessories not recom-
mended by the manufacturer of this product. The use of
attachments or accessories not recommended can result
in serious personal injury.
The water supply must come from a water main. NEVER use
hot water or water from pools, lakes, etc. Before connecting
the garden hose to the pressure washer:
Run water through the hose for 30 seconds to clean any
debris from the hose.
Inspect the screen in the water intake.
If the screen is damaged, do not use the machine until
the screen has been replaced.
If the screen is dirty, clean it before connecting the garden
hose to the machine.
To connect the garden hose to the machine:
Completely uncoil the garden hose or remove completely
from reel to prevent kinks.
NOTE: There must be a minimum of 10 feet of unrestricted
hose between the pressure washer intake and the hose
faucet or shut off valve (such as a “Y” shut off connector).
With the hose faucet turned completely off, attach the
end of the garden hose to the water intake. Tighten by
hand.
NOTICE:
Do not run the pressure washer without water supply
connected and turned on, as this may damage the high
pressure seals and decrease pump life. Completely
unwind the hose from its reel or coil and make sure the
hose is not being restricted by tires, rocks, or any other
objects that may lessen or prevent water flow to the
pressure washer.
ASSEMBLY
OPERATION
WARNING:
Never direct a water stream toward people or pets, or
any electrical device. Failure to follow these instructions
could result in serious injury, electric shock, or death.
NOTICE:
Before each use, inspect the entire product for damaged,
missing, or loose parts such as screws, nuts, bolts, caps,
etc. Tighten securely all fasteners and caps and do not
operate this product until all missing or damaged parts
are replaced. Please call customer service or contact an
authorized service center for assistance.
APPLICATIONS
You may use this tool around the house for cleaning most
small to large horizontal or vertical exterior surfaces, smaller
exterior objects and structures, and outdoor equipment and
tools.* You can:
11 — English
NOTICE:
Routinely make a visual inspection of the pump and
motor during use. If you notice any lubricant leaking
around the pump or motor seals, stop using the pres-
sure washer immediately. Contact customer service or
a qualified service center for repair. Failure to do so may
cause property damage.
To stop the motor:
Put the on/off switch in the OFF position.
Pull trigger to release water pressure.
NOTE: The pressure washer may be on and the system
may have pressure even when the pump and/or motor
cannot be heard running. Always use caution around the
pressure washer.
USING THE TRIGGER HANDLE
See Figure 10.
WARNING:
Hold the trigger handle securely with both hands. Expect
the trigger handle to move when the trigger is pulled due
to reaction forces. Failure to do so could cause loss of
control and injury to yourself and others.
Pull back and hold the trigger to operate the pressure
washer.
Release the trigger to stop the flow of water through the
nozzle.
To engage the lock out:
Push up on the lock out until it clicks into the slot.
To disengage the lock out:
Push the lock out down and into its original position.
Start with the nozzle 1–2 ft. away from the cleaning surface
and carefully approach the surface just until the desired
level of cleaning is achieved. If the spray is too close it can
damage the cleaning surface.
SELECTING THE RIGHT NOZZLE FOR THE JOB
See Figure 11.
Each of the nozzles has a different spray pattern. Before
starting any cleaning job, determine the best nozzle for the
job. Refer to the Nozzle Selection Guide for more informa-
tion about which nozzle to choose.
Clean or remove mold and mildew from weathered decks,
driveways, patios, walkways, sidewalks, etc.
Remove dirt from various exterior vertical surfaces such
as house exteriors, siding, fences, brick, concrete or stone
walls, etc.
Wash boats, outdoor furniture, powered or non-powered
garden equipment, gutters, window screens, grills, play-
ground equipment, etc.
*Always test in an inconspicuous area first.
STARTING AND STOPPING THE PRESSURE
WASHER
See Figure 9.
NOTICE:
Do not run the pressure washer without water supply
connected and turned on, as this may damage the high
pressure seals and decrease pump life. Completely
unwind the hose from its reel or coil and make sure the
hose is not being restricted by tires, rocks, or any other
objects that may lessen or prevent water flow to the
pressure washer.
Before starting the motor:
Connect all hoses.
NOTE: Make sure the pressure washer’s water intake
screen is in place and unclogged before connecting
garden hose.
Turn on the garden hose then pull the trigger to relieve air
pressure; hold the trigger until a steady stream of water
appears.
NOTE: Make sure the faucet is turned on fully and that
there are no kinks or leaks in the hose.
To start the motor:
With the on/off switch in the OFF position, connect the
pressure washer to the power supply.
NOTE: If using an extension cord, make sure to arrange
a drip loop as described on page 2.
WARNING:
To reduce the risk of electrocution, keep all connections
dry and off the ground. Do not touch plug with wet hands.
Press the reset button on the pressure washer’s plug to
make sure the unit is ready for operation.
Put the on/off switch in the ON position to start the motor.
OPERATION
12 — English
Turn off the pressure washer, disconnect from power
supply, and shut off the water supply. Pull trigger to
release water pressure.
Engage the lock-out on the trigger handle by pushing up
on the lock-out until it clicks into the slot.
Pull back and hold the quick-connect collar.
Remove the nozzle by pulling it from the quick-connect
collar. Place nozzle in the nozzle storage area on the top
of the machine.
USING THE HIGH PRESSURE HOSE
WARNING:
Injection hazard. Fully unwrap and straighten high pres-
sure hose prior to and during each use and do not allow
it to become kinked. The high pressure hose features an
outer covering that provides strength to the hose. If the
outer covering becomes damaged, stop using the hose
and replace it immediately. A kinked or damaged hose
can develop a high pressure leak and result in a possible
injection or other serious personal injury.
To prevent damage to the outer covering:
Inspect the hose before every use.
WARNING:
NEVER remove nozzles without first turning off the motor,
disconnect from power supply, relieving the water pres-
sure in the trigger handle, and locking the lock out on the
trigger handle. NEVER point the nozzle at your face or at
others. The quick-connect feature contains small springs
that could eject the nozzle with some force. Failure to
follow these instructions could result in an eye injury or
other serious personal injury.
To connect a nozzle to the spray wand:
Turn off the pressure washer, disconnect from power
supply, and shut off the water supply. Pull trigger to
release water pressure.
Engage the lock-out on the trigger handle by pushing up
on the lock-out until it clicks into the slot.
Pull back the quick-connect collar.
Push the nozzle into place in the spray wand.
Push the collar forward so that the nozzle is secured
properly. Check to see that the nozzle is secure.
To disconnect a nozzle from the spray wand once the
cleaning job is complete:
NOZZLE SELECTION GUIDE
HIGH PRESSURE
(NO SOAP WHEN USING THESE NOZZLES)
LOW PRESSURE
(FOR SOAP OR
GENTLE RINSE)
Turbo Nozzle
15º
Blue or Black
Soap Nozzle
Concrete, Brick, Masonry
Siding, Gutters, House
Fencing, Deck, Patio
Lawn Equipment, Boat, RV
Recommended Nozzle Use With Caution for Certain Applications
OPERATION
13 — English
OPERATION
Fully unwrap and straighten hose before use.
Do not allow the high pressure hose to be kinked.
Keep hose away from hot surfaces and sharp edges.
Do not pull unit by high pressure hose.
Do not allow hose to be crushed or wrapped around
objects.
WASHING WITH DETERGENT
See Figures 12 - 13.
As sold, this unit is designed for use with “downstream” pres-
sure washer detergents. To convert for use with “upstream”
detergents, contact customer service or an authorized service
center for more information.
NOTICE:
USE ONLY DETERGENTS DESIGNED FOR PRES-
SURE WASHERS. Do not use household detergents,
acids, alkalines, bleaches, solvents, flammable material,
or industrial grade solutions, which can damage the
pump or cause property damage. Many detergents may
require mixing prior to use. Prepare cleaning solution
as instructed on the solution bottle. Always test in an
inconspicuous area before beginning.
Disconnect pressure washer from power supply.
Pour detergent in the soap tank. Use a funnel, if needed,
to prevent accidental spilling of the detergent outside
the tank. If any detergent is spilled during the filling
process, make sure the unit is cleaned and dried before
proceeding.
NOTE: The machine setting of this unit is 20:1, which usu-
ally allows the use of 1 gallon pressure washer detergent
without further dilution. Check your detergent instructions
to be sure additional dilution is not necessary.
Install the blue or black soap nozzle on the spray wand.
Connect unit to power supply and turn the pressure
washer on.
Squeeze the trigger and wait approximately 5 seconds
for the detergent to appear.
Spray the detergent on a dry surface using long, even,
overlapping strokes. To prevent streaking, do not allow
detergent to dry on the surface.
Before shutting off the motor:
Fill the soap tank with clean water.
Spray the clear water through the spray wand until the
tank is empty.
If any detergent remains in the spray, repeat with a second
tank of clean water.
Shut off the motor.
NOTE: Shutting off the motor will not relieve pressure in the
system. Pull trigger to release water pressure.
RINSING WITH THE PRESSURE WASHER
Turn off the pressure washer and shut off the water
supply. Pull trigger to release water pressure.
Engage the lock out on the trigger handle by pushing up
on the lock out until it clicks into the slot.
Remove the soap nozzle and place it in the nozzle storage
area on the machine.
Select the right nozzle for the job. See the chart shown
earlier in the manual to select the appropriate nozzle.
Start at the top of the area to be rinsed and work down,
overlapping the strokes.
USING PUMP PROTECTOR
See Figure 14.
Regular use of a commercially available pump protector
prolongs the life of the pressure washer by removing hard
water mineral deposits, lubricating pump seals and pistons,
and preventing freeze damage. Pump protector should be
added to the unit after every use and before storage. Pump
protector can be purchased at the retailer where you pur-
chased your pressure washer, or by calling customer service.
The instructions that follow are typical for adding pump pro-
tector but you should always verify the specific instructions
provided by the manufacturer of the pump protector used.
Turn off the pressure washer motor and shut off the water
supply. Pull trigger to release water pressure.
Disconnect garden hose and high pressure hose.
Unscrew threaded top from pump protector bottle and
remove paper seal from bottle. Reinstall top on bottle and
tighten securely.
NOTE: The rubber seal should remain inside the threaded
top. If it comes out, be sure to replace before reinstalling
the top.
Remove bottle cap and attach threaded end of bottle
securely to pressure washer pump water intake.
Squeeze bottle to inject contents into pump.
Pump is protected when the protector fluid exits the pump
outlet.
POWER CORD STORAGE
See Figure 15.
When it is not in use, the power cord may be coiled and
suspended from the storage hook on the handle.
To secure the power cord in place, use the attached bungee
cord.
MOVING THE PRESSURE WASHER
See Figure 16.
NOTE: Never lift or carry this product using the handle and
never place the unit in any position other than upright on
its wheels.
14 — English
OPERATION
Turn the pressure washer off. Point nozzle in a safe direc-
tion and pull trigger to release water pressure.
Tilt the machine toward you slightly until it balances on
the wheels then roll the machine to the desired position.
Do not tilt forward or sideways when moving.
DO NOT attempt to move the unit by pulling on any of
the hoses.
MAINTENANCE
WARNING:
Before inspecting, cleaning, or servicing the machine,
shut off motor, wait for all moving parts to stop, discon-
nect unit from power supply, and pull trigger to release
water pressure. Failure to follow these instructions can
result in serious personal injury or property damage.
WARNING:
Always wear eye protection with side shields marked to
comply with ANSI Z87.1. Failure to do so could result in
objects being thrown into your eyes, resulting in possible
serious injury.
WARNING:
When servicing, use only identical replacement parts.
Use of any other parts could create a hazard or cause
product damage.
NOTICE:
Periodically inspect the entire product for damaged,
missing, or loose parts such as screws, nuts, bolts, caps,
etc. Tighten securely all fasteners and caps and do not
operate this product until all missing or damaged parts
are replaced. Please call customer service or contact an
authorized service center for assistance.
GENERAL MAINTENANCE
Avoid using solvents when cleaning plastic parts. Most
plastics are susceptible to damage from various types of
commercial solvents and may be damaged by their use. Use
clean cloths to remove dirt, dust, oil, grease, etc.
WARNING:
Do not at any time let brake fluids, gasoline, petroleum-
based products, penetrating oils, etc., come in contact
with plastic parts. Chemicals can damage, weaken, or
destroy plastic which could result in serious personal
injury.
POWER SUPPLY CORD REPLACEMENT
If replacement of the power supply cord is necessary, this
must be done by an authorized service center in order to
avoid a safety hazard.
PUMP LUBRICATION
The pump on this unit is lubricated with a sufficient amount
of high grade lubricant for the life of the unit under normal
operating conditions. Therefore, no further lubrication is
required.
PUMP MAINTENANCE
Routinely make a visual inspection of the pump. If you notice
any leaking of lubricant around the pump seals, take the
pressure washer to an authorized service center for repair.
There are no user serviceable parts to the pressure washer
pump. Any attempt to service or alter the pump may dam-
age the pressure washer and void your product warranty.
NOZZLE MAINTENANCE
See Figure 17.
Excessive pump pressure (a pulsing sensation felt while
squeezing the trigger) may be the result of a clogged or
dirty nozzle.
Turn off the pressure washer, disconnect from power
supply, and shut off the water supply. Pull trigger to
release water pressure.
Remove the nozzle from the spray wand.
15 — English
WARNING:
NEVER remove nozzles without first turning off the mo-
tor, disconnecting from power supply, relieving the water
pressure in the trigger handle, and locking the lock out
on the trigger handle. NEVER point the nozzle at your
face or at others. The quick-connect feature contains
small springs that could eject the nozzle with some force.
Failure to follow these instructions could result in an eye
injury or other serious personal injury.
To free any foreign materials clogging or restricting the
nozzle, blow out or remove debris with a straightened
paper clip or fine needle (not included).
Using a garden hose, flush debris out of nozzle by back
flushing (running the water through the nozzle backwards
or from the outside to the inside).
Reconnect the nozzle to the spray wand.
Turn on the water supply and start the motor.
STORING THE PRESSURE WASHER
See Figures 18 - 19.
NOTE: Regular use of pump protector will give you better
performance of the unit and increase the life of the pump.
Store in a dry, covered area where the weather can’t damage it.
It is important to store this product in a frost-free area. Al-
ways empty water from all hoses, the pump, and the soap
tank before storing.
Make sure the on/off switch is in the OFF position.
Disconnect both the high pressure hose and the garden
hose from the pump.
Tilt the unit as shown to allow any remaining water in the
pump to drain from the water inlet.
NOTICE:
If the location where your pressure washer is stored will
fall below 32°F, the use of a pump protector is required
before storing to prevent freeze damage. Freeze damage
will void your warranty.
Store the unit and accessories in an area that does not
reach freezing temperatures. Do not store near furnace or
other sources of heat that could dry out the pump seals.
MAINTENANCE
This product has a Three-year Limited Warranty for personal,
family, or household use (90 days for business or commercial use).
For warranty details, visit www.ryobitools.com
or call (toll free) 1-800-860-4050.
16 — English
PROBLEM POSSIBLE CAUSE SOLUTION
Pressure washer does not start
when trigger is depressed
Power cord not connected to power
source.
The on/off switch is in the OFF
position.
GFCI is tripped.
House/shop circuit breaker is tripped.
Water pressure in hose.
Receptacle is bad.
Connect the power cord to a live
120V AC, 60 Hz AC receptacle.
Put the on/off switch in the ON
position.
Press reset button on the GFCI
plug.
Reset house/shop breaker. Make
sure pressure washer is connected
to an individual branch circuit only.
If using an extension cord, make
sure it is heavy enough to carry the
current of the pressure washer.
Squeeze trigger to relieve water
pressure.
Try another receptacle.
Pump doesn’t produce pressure Inadequate water supply.
Spray wand leaks.
Nozzle is clogged.
Pump is faulty.
Air in line.
Water inlet filter is clogged or dirty.
Provide adequate water flow.
Check connections and / or
replace wand.
Clean nozzle.
Contact authorized service center.
Squeeze trigger on spray wand to
remove air from line.
Remove the water inlet filter, rinse
with warm water, then replace in
unit.
Machine doesn’t reach high
pressure
Diameter of garden hose is too small.
Water supply is restricted.
Not enough inlet water.
Hose is leaking.
Kink in hose.
Replace with 3/4 in. garden hose.
Check garden hose for kinks, leaks,
and blockages.
Open water source full force.
Replace hose.
Eliminate kinks in hose.
No detergent Soap tank is empty.
Water supply is inadequate or
clogged.
Wrong nozzle is attached.
Add additional detergent to tank.
Check garden hose for kinks, leaks
and blockages.
Attach blue or black soap nozzle.
Wand leaks O-ring needs replacing. Replace o-ring. If this does not
correct the problem, contact
your authorized service center to
purchase a new wand.
TROUBLESHOOTING
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52

Ryobi RY142300 Le manuel du propriétaire

Catégorie
Nettoyeurs haute pression
Taper
Le manuel du propriétaire
Ce manuel convient également à