resideo CT230-GA/U Guide d'installation

INSTALLATION GUIDE

GUIDE D’INSTALLATION

GUÍA DE INSTALACIÓN

CT230-GA / CT230-GB

LINKED UNIT

UNITÉ ESCLAVE

UNIDAD ENLAZADA

33-00222EFS-04

Need Help?

We are here to help. Call 1-800-468-1502.

Besoin d’aide?

Nous sommes là. Composez le 1 800 468-1502.

¿Asistencia?

Estamos aquí para ayudarlo. Llame al 1 800 468-1502.

CT230-GA / CT230-GB

1

ENGLISH

Read the entire document

CAUTION:

• Installation must be carried out by a certified electrician and must comply with national and

local electrical codes.

• Use the CT230 linked unit for resistive load only.

• Do NOT install the CT230 linked unit in an area where it can be exposed to water or rain.

• To prevent severe shock or electrocution, always turn the power OFF at the service panel

before working with wiring.

• Install the CT230 linked unit onto an electrical box.

• Connect the wires using solderless connectors for copper wires. Use special CO/ALR

solderless connectors for connection to aluminum wires.

• Keep the top and bottom air vents (openings) of the CT230 clean and unobstructed at all

times.

Before you start

Installation Guide

2

ENGLISH

The CT230 linked unit is designed to be used in a system for large floor heating applications whose

load is too high for a single conventional thermostat. The system consists of a master thermostat

and multiple CT230 linked units (see diagram on the following page). The heating area is divided

into zones of 15 A or less, each zone connected to a CT230 linked unit. The user sets the tempera-

ture and programs the heating schedule on the master thermostat.

• Each CT230 linked unit is powered by line voltage (120 VAC, 208 VAC or 240 VAC) and has its

own ground fault protection mechanism. Up to 10 CT230 linked units can be used in a given

setup.

• The master thermostat (not included) can be a TH114 or TH115 thermostat operating on

12 VDC. The master thermostat is powered by one of the CT230 linked units.

Supplied Parts

• One (1) CT230 linked unit

• Two (2) mounting screws

• Four (4) solderless connectors for copper wires

About the CT230 linked unit

CT230-GA / CT230-GB

3

ENGLISH

System diagram

Master

thermostat

CT230

Up to 10

zones

Sensor

cable

Heating

cables

(zone 1)

CT230 CT230

Heating

cables

(zone 2)

Heating

cables

(zone 3)

Installation Guide

4

ENGLISH

Install each CT230 linked unit as follows:

Turn the heating system off at the main electrical panel.

Loosen the bottom screw and remove the CT230 faceplate

from the wallplate. (The screw cannot be completely

removed.)

Connect the wallplate to the load (heating cables) and to the

power supply (see wiring diagram on page 6).

NOTE: The CT230 linked units can operate on different

voltages in the same setup (e.g., 5 units @ 120 V and

5@240V).

Install the wallplate to the electrical box using the provided

screws.

Installing the CT230 linked units

Wall-

Faceplate

CT230-GA / CT230-GB

5

ENGLISH

If not already done, affix the provided terminal sticker to the

wallplate.

Insert the wires (not included) through one of the two

openings on the wallplate and connect the CT230 linked units

together in a daisy-chain configuration (see connection

diagram on page 7).

Reinstall the faceplate on the wall plate and tighten the screw.

Access the ON/OFF switch by sliding the CT230 door upwards

and place the CT230 linked unit on OFF.

Sticker

Switch

Door

Installation Guide

6

ENGLISH

NOTE: Connect the wires using the provided solderless connectors for copper wires:

Wiring diagram

120 V

240 V

Load

Black

Red

Black

Red

Black

Power

supply

Load

Black

Red

White

Black

Red

White

Black

Power

supply

Black

CT230-GA / CT230-GB

7

ENGLISH

Connection diagram

Sensor

CT230

Master

thermostat

NOTE:

• The wire distance between the master thermostat and each CT230 unit must not exceed

500 ft. (150 m). 20-AWG wires are recommended.

• The floor sensor cable must not exceed 200 ft. (60 m).

CT230 CT230

Up to 10 CT230

linked units

Installation Guide

8

ENGLISH

WARNING: Make sure all CT230 linked units are Off.

Connect the master thermostat to the nearest CT230 linked unit (see connection diagram on

page 7).

WARNING: Only one CT230 linked unit must be used to power the master thermostat.

Connect the floor sensor (included with the TH114-AF-12VDC & TH115-AF-12VDC

thermostat) to the master thermostat (no polarity, see connection diagram on page 7).

• Position the sensor cable such that it does not come in contact with the floor heating wires. The

sensor must be centered between two floor heating wires for best temperature control.

• Do NOT staple the sensor head (the plastic end) to the floor. Doing so might damage the sensor.

Any damage might not be noticeable during testing but can become apparent several days later.

Loosen the bottom screw and remove the faceplate from the wallplate. (The screw cannot be

completely removed.)

Install the wallplate on the wall using the provided screws and wall anchors.

Reinstall the faceplate on the wallplate.

Apply power to heating system and switch each CT230 linked unit and the master thermostat

to On.

Test the ground fault protection on each CT230 linked unit.

Installing the master thermostat

CT230-GA / CT230-GB

9

ENGLISH

The CT230 linked unit, with built-in ground fault protection, is different from conventional

thermostats. In the event of a ground fault, the ground fault protection mechanism on the CT230

linked unit will trip and quickly stop the flow of electricity to prevent serious injury.

Definition of a ground fault

Instead of following its normal safe path, electricity passes through a person’s body to reach the

ground. For example, a defective floor heating mat can cause a ground fault.

Ground fault protection, does not protect against circuit overloads, short circuits, or electrical

shocks. For example, you can still receive an electrical shock if you touch bare wires while standing

on a non-conducting surface such as a wood floor.

Ground fault protection reset

When the ground fault protection mechanism trips, the TEST light is On (red). To reset the ground

fault protection, switch the CT230 linked unit to OFF and back to ON. The TEST light will turn off if

the ground fault protection is functioning properly.

End of Life

If the TEST light is flashing permanently the device must be replaced.

Ground fault protection (GFCI)

Installation Guide

10

ENGLISH

Testing the ground fault protection

To ensure the ground fault protection on each CT230 linked unit is always in working order, test it

after installation and on a monthly basis thereafter.

Increase the setpoint temperature on the master thermostat above the

measured temperature in order to activate the heating system.

Press the TEST button.

• If the TEST light does NOT turn On, the test has failed. Cut power to the

heating system at the main electrical panel, have an electrician verify the

installation and, if necessary, replace the CT230 linked unit.

• If the TEST light turns on, continue the test.

Switch the CT230 linked unit to OFF then back to ON.

• If the TEST light turns off, the test has passed. Set the master thermostat back to the desired

temperature. The test is now completed.

• If the TEST light remains on, the test has failed. Continue with the rest of the procedure.

Switch the circuit breaker (at the service panel) of the heating system to off then back to on.

Repeat the test. If the test fails again, cut power to the heating system at the main electrical

panel, have an electrician verify the installation and, if necessary, replace the CT230 linked

unit.

TEST button/light

CT230-GA / CT230-GB

11

ENGLISH

Technical Specifications

Model Supply

Max. load (resistive only) Ground Fault

Protection

(GFCI)

Wiring

Current Power

CT230-GA

120 VAC, 60 Hz

15 A

1800 W

5 mA

4 wires,

double pole

240 VAC, 60 Hz 3600 W

CT230-GB

120 VAC, 60 Hz 1800 W

15 mA

240 VAC, 60 Hz 3600 W

Installation Guide

12

ENGLISH

Resideo warrants this product, excluding battery, to be free from defects in workmanship or materials, under normal use and service, for a period of three (3) years

from the date of first purchase by the original purchaser. If at any time during the warranty period the product is determined to be defective due to workmanship or

materials, Resideo shall repair or replace it (at Resideo's option).

If the product is defective,

(i) return it, with a bill of sale or other dated proof of purchase, to the place from which you purchased it; or

(ii) call Resideo Customer Care at 1-800-468-1502. Customer Care will make the determination whether the product should be returned to the following address:

Resideo Return Goods, 1985 Douglas Dr. N., Golden Valley, MN 55422, or whether a replacement product can be sent to you.

This warranty does not cover removal or reinstallation costs. This warranty shall not apply if it is shown by Resideo that the defect was caused by damage which

occurred while the product was in the possession of a consumer.

Resideo's sole responsibility shall be to repair or replace the product within the terms stated above. RESIDEO SHALL NOT BE LIABLE FOR ANY LOSS OR DAMAGE OF

ANY KIND, INCLUDING ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING, DIRECTLY OR INDIRECTLY, FROM ANY BREACH OF ANY WARRANTY,

EXPRESS OR IMPLIED, OR ANY OTHER FAILURE OF THIS PRODUCT.

Some states do not allow the exclusion or limitation of incidental or consequential damages, so this limitation may not apply to you.

THIS WARRANTY IS THE ONLY EXPRESS WARRANTY RESIDEO MAKES ON THIS PRODUCT. THE DURATION OF ANY IMPLIED WARRANTIES, INCLUDING THE WAR-

RANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, IS HEREBY LIMITED TO THE THREE YEAR DURATION OF THIS WARRANTY. Some

states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you.

This warranty gives you specific legal rights, and you may have other rights which vary from state to state. If you have any questions concerning this warranty, please

write Resideo Customer Care, 1985 Douglas Dr, Golden Valley, MN 55422 or call 1-800-468-1502.

Warranty

CT230-GA / CT230-GB

1

FRANÇAIS

Veuillez lire le document en entier

MISE EN GARDE :

• L’installation doit être effectuée par un électricien certifié et doit être conforme aux codes

nationaux et locaux de l’électricité.

• Utiliser l’unité CT230 pour une charge résistive seulement.

• Ne PAS installer l’unité CT230 à un endroit où il risque d’être exposé à l’eau ou à la pluie.

• Afin de prévenir les chocs électriques graves ou les électrocutions, toujours COUPER le

courant à partir du panneau électrique principal avant de travailler avec le câblage.

• Installer l’unité CT230 sur une boîte électrique.

• Relier les fils avec des connecteurs sans soudure pour fils de cuivre. Pour le raccordement à

des fils d'aluminium, utiliser des connecteurs marqués CO/ALR conçus à cette fin.

• Garder les ouvertures d’aération de l’unité CT230 propres et dégagées en tout temps.

Avant de commencer

Guide d’installation

2

FRANÇAIS

L’unité CT230 est conçu pour être utilisé dans un installation pour planchers chauffants de grande

surface ayant une charge trop élevée pour un seul thermostat conventionnel. L’installation com-

prend un thermostat maître et plusieurs unités CT230 (voir le schéma sur la page suivante). Ce sys-

tème permet de diviser la surface à chauffer en zones de 15 A ou moins. Chaque zone est reliée à

un unité CT230. L'utilisateur règle la température et programme l'horaire de chauffage à partir du

thermostat maître.

• Chaque unité CT230 est alimenté par la tension secteur (120 VAC, 208 VAC ou 240 VAC) et est

muni de son propre dispositif de protection de fuite à la terre. Le nombre maximale des unités

CT230 dans une installation est de 10.

• Le thermostat maître (non compris) peut être un thermostat TH114 ou TH115 fonctionnant

sous 12 VCC. Le thermostat maître reçoit son alimentation d'un des unités CT230.

Pièces fournies

•Un (1) unité CT230

• Deux (2) vis de montage

• Quatre (4) connecteurs sans soudure pour fils de cuivre

À propos de l’unité CT230

CT230-GA / CT230-GB

3

FRANÇAIS

Schéma du système

thermostat

maître

CT230

maximum de 10

zones

fils de la sonde

câbles chauffants

(zone 1)

CT230 CT230

câbles chauffants

(zone 2)

câbles chauffants

(zone 3)

Guide d’installation

4

FRANÇAIS

Installer chaque unité CT230 comme suit :

Mettre le système de chauffage hors tension à partir du pan-

neau électrique principal.

Desserrer la vis sous l’unité CT230 et séparer la façade de la

plaque murale. (La vis ne peut être complètement retirée.)

Brancher la plaque murale à la charge (câbles chauffants) et à

l’alimentation (voir le schéma de branchement à la page 6).

NOTA: Les unités CT230 peuvent fonctionner sur des

tensions différentes (p. ex. 5 unités sur du 120 V et 5 unités

sur du 240 V).

Fixer la plaque murale à la boite électrique avec les vis

fournies.

Installation des unités CT230

plaque

murale

façade

CT230-GA / CT230-GB

5

FRANÇAIS

Si ce n'est pas déjà fait, apposer l'autocollant fourni à la

plaque murale.

Insérer les fils (non compris) dans l'une des deux ouvertures

de la plaque murale et relier ensemble les unités esclaves

CT230 en guirlande (voir le diagramme de raccordement à la

page 7).

Réinstaller la façade sur la plaque murale et serrer la vis.

Glisser le couvercle vers le haut et basculer l’interrupteur à OFF.

collant

interrupteur

couvercle

Guide d’installation

6

FRANÇAIS

NOTA : Relier les fils en utilisant des connecteurs sans soudure pour fils de cuivre.

Schéma de branchement

120 V

charge

alimentation

noir

rouge

noir

rouge

noir

240 V alimentation

charge

noir

rouge

blanc

noir

rouge

blanc

noir

La page charge ...

resideo CT230-GA/U Guide d'installation

Ce manuel convient également à

resideo CT230-GA/U Guide d'installation

dans d''autres langues

Documents connexes

Autres documents