Aube TH115-AF-GA Le manuel du propriétaire

Catégorie
Thermostats
Taper
Le manuel du propriétaire
M39031
Owner’s Guide
Guide du propriétaire
Guía para el usuario
TH115-AF-GA / TH115-AF-GB
Programmable thermostat
Thermostat programmable
Termostato programable
33-00221EFS-08
Need Help?
For assistance with this product please visit https://www.resideo.com
Besoin d’aide?
Pour obtenir de l’aide, visitez https://www.resideo.com
¿Asistencia?
Para obtener ayuda sobre este producto, visite https://www.resideo.com
ENGLISH
TH115-AF-GA / TH115-AF-GB
Overview
Before you start..................................................2
About your thermostat........................................3
Controls..............................................................4
Display ...............................................................5
Installation
Installing the thermostat.....................................6
Wiring diagrams .................................................7
Connecting the floor sensor / remote control .....8
Setting the configuration switches......................9
Setup
Time and day....................................................10
Daylight Saving Time .......................................11
Floor temperature limits ...................................12
Preset temperatures.........................................13
Default schedule ..............................................14
Modifying the schedule ....................................15
Operation
Running the schedule (Automatic mode) .........16
Temporary override of schedule.......................16
Permanent override (Manual mode) ...............17
Before going on vacation (Vacation mode) ......17
Ground fault protection (GFCI).........................18
Appendices
Error messages................................................20
Technical specifications....................................21
Customer assistance........................................22
Warranty...........................................................23
Table of contents
Owner’s Guide
2
ENGLISH
Read the entire document
CAUTION:
Installation must be carried out by a certified electrician and must comply with national and
local electrical codes.
Use this thermostat for resistive loads only.
Do NOT install the thermostat in an area where it can be exposed to water or rain.
To prevent severe shock or electrocution, always turn the power Off at the service panel
before working with wiring.
Install the thermostat onto an electrical box.
Use special CO/ALR solderless connectors if you connect the thermostat to aluminum wires.
Keep the thermostat's top and bottom air vents (openings) clean and unobstructed at all
times.
Before you start
TH115-AF-GA / TH115-AF-GB
3
ENGLISH
The TH115 programmable thermostat has three temperature control modes:
See page 9 on how to change the temperature control mode setting.
Supplied Parts
One (1) thermostat
Two (2) mounting screws
Four (4) solderless connectors for copper wires
One (1) floor sensor
One (1) flat-tip screwdriver
About your thermostat
A mode: controls the ambient air temperature
F mode: controls the floor temperature using an external temperature sensor
AF mode: controls the ambient air temperature
maintains the floor temperature within desired limits using an external temperature
sensor
Owner’s Guide
4
ENGLISH
Controls
M39032
On/Off switch*
Day button
Temperature adjustment buttons**
Program button
Mode selection / program exit
Preset temperature buttons
(see page 13)
Backlight button**
Program clear button
Hour button
Minutes button
*
Place at Off to cut power to the heater (e.g., in the summer). This will not affect the time and temperature settings.
** When the backlight button or either of the buttons is pressed, the display illuminates for 12 seconds.
TEST light/button for ground
fault protection (see page 18)
TH115-AF-GA / TH115-AF-GB
5
ENGLISH
Display
M39033
Temperature*
Operation mode icon
(see pages 16 & 17)
Period (see page 14)
Time
Number of flames varies
according to heating intensity
Preset temperature icon (see page 13)
Appears when the setpoint
temperature is displayed*
Temperature control mode
(see pages 3 & 9)
Ground fault indicator (see page 18)
Day
* The thermostat normally displays the actual (measured) temperature. To view the setpoint temperature, briefly press
either of the buttons. The setpoint will appear for 5 seconds. To change the setpoint temperature, press one of the
buttons until the desired temperature is displayed. To scroll faster, press and hold the button.
Owner’s Guide
6
ENGLISH
Turn the heating system off at the main electrical panel.
Loosen the bottom screw and remove the thermostat faceplate from its
wallplate. (The screw cannot be completely removed.)
Connect the thermostat to the load and to the power supply (see page 7).
Connect the floor sensor (see page 8).
If you wish to connect a remote control device, see page 8.
Install the wallplate to the electrical box using the provided screws.
Set the configuration switches on the back of the faceplate (see page 9).
Install the faceplate back on the wall plate and tighten the screw.
Apply power to the heating system.
Test the ground fault protection (see page 19).
Installing the thermostat
M39034
Wallplate
Faceplate
TH115-AF-GA / TH115-AF-GB
7
ENGLISH
NOTE: Connect the wires using the provided solderless connectors for copper wires.
Wiring diagram
M39036
L1(L)
L2(N)
M39035
L1(L)
L2(N)
120 V
Load
Power
supply
Black
Red
Red
Black
Black
Red
Red
Black
240 V Power
supply
Load
Black
Red
White
Black
Red
White
Black
Black Black
Owner’s Guide
8
ENGLISH
Insert the floor sensor cable through one of the two
openings on the wallplate and connect the sensor
wires to terminals 1 and 2 (no polarity).
The sensor cable must not come in contact with the
electrical wires and must be routed outside the
electrical box and follow the wall down to the floor.
Position the sensor cable such that it does not
come in contact with the floor heating wires. The
sensor must be centered between two floor heating
wires for best temperature control.
Do NOT staple the sensor head (the plastic end) to
the floor. Doing so might damage the sensor. Any
damage might not be noticeable during testing but
can become apparent several days later.
If you wish to connect a remote control device (see
page 17), insert the wires (use 18- to 22-gauge flexible
wires) through one of the two openings on the wallplate
and connect them to terminals 2 and 3 (no polarity).
Connecting the floor sensor / remote control
M39037
TEST
Floor
temperature
sensor
Remote control device
TH115-AF-GA / TH115-AF-GB
9
ENGLISH
Configuration switches are on the back of the faceplate.
Set the configuration switches
# Configurations Up Down
1 Display format °F / 12 h °C / 24 h
2Early Start1
1. Early Start is used in Automatic mode only. When Early Start is enabled (on), the thermostat determines when to start
heating so the Comfort temperature is attained at the beginning of periods 1 and 3. When Early Start is disabled (off),
heating starts only at the beginning of periods 1 and 3; thus there is a delay before the Comfort temperature is
reached.
Enable Disable
3Temperature control mode2
2. See page 3. To select the F Mode, place the switch in the F position. To select the AF Mode, place the switch in the AF
position and ensure that the temperature sensor is connected to the thermostat. To select the A Mode, place the switch in
the AF position and ensure that the remote temperature sensor is
NOT
connected to the thermostat.
FAF
M38981
Owner’s Guide
10
ENGLISH
To set the clock and the day:
Press the Hour button to set the hour.
Press the Min button to set the minutes.
Press the Day button to set the day.
Press the Mode/Ret button to return the thermostat to normal display.
NOTE: The thermostat will automatically return to normal display if no button is
pressed for 60 seconds.
Time and day
TH115-AF-GA / TH115-AF-GB
11
ENGLISH
When the Daylight Saving Time function is enabled (On), the thermostat automatically switches to Daylight Saving
Time on the second Sunday of March and to normal time on the first Sunday of November.
NOTE: The Daylight Saving Time function is disabled (default setting) when the clock loses its setting.
To set the
Daylight Saving Time function and to set the date:
Press the Day button (3 seconds) until DLS appears on the screen.
Press either of the buttons to toggle between On (enabled) and Off (disabled).
Press the Day button briefly. The year setting is displayed.
Press either of the buttons to set the current year.
Press the Day button briefly. The month setting is displayed.
Press either of the buttons to set the current month.
Press the Day button briefly. The date setting is displayed.
Press either of the buttons to set the current date.
Press the Mode/Ret button to return the thermostat to normal display.
NOTE: The thermostat will automatically return to normal display if no button is pressed for 60 seconds.
Daylight Saving Time
Owner’s Guide
12
ENGLISH
WARNING: To avoid damaging your floor, follow your floor supplier’s recommendations regarding floor tempera-
ture limits.
The minimum and maximum floor temperature limits are 5.0°C (41°F) and 28.0°C (82°F) by default.
To modify these limits, proceed as follows:
Switch the thermostat to Off.
Press and hold the button.
Switch the thermostat back to On.
Release the button when the minimum temperature limit (FL:LO) appears.
Set the minimum temperature limit using the buttons.
Press the button to display the maximum temperature limit (FL:HI).
Set the maximum temperature limit using the buttons.
Press Mode/Ret to return the thermostat to normal display.
NOTE: The thermostat will automatically return to normal display if no button is pressed for 60 seconds.
Floor temperature limits (AF mode only)
M38985
M38986
TH115-AF-GA / TH115-AF-GB
13
ENGLISH
The thermostat has 3 preset temperatures. Their default settings are shown in the following table.
To use a preset temperature:
Briefly press the appropriate preset temperature button ( , or ). The preset temperature will
become the current setpoint and its icon will appear on the screen.
To modify a preset temperature:
Press one of the buttons to display the desired temperature.
Press and hold the appropriate preset temperature button ( , or ) until its icon is displayed.
Preset temperatures
Preset temperature Intended use Icon A/AF modes F mode
Comfort When at home 21.0°C (70°F) 28.0°C (82°F)
Economy When asleep or away from home 17.0°C (63°F) 20.0°C (68°F)
Vacation During prolonged absence 10.0°C (50°F) 10.0°C (50°F)
Owner’s Guide
14
ENGLISH
The schedule consists of 4 periods per day, which represents a typical work day. The Comfort ( ) preset
temperature is automatically used in Periods 1 and 3 and the Economy ( ) preset temperature in Periods
2 and 4. You can program the thermostat to skip (cancel) the periods that do not apply to your situation. For
example, you can skip periods 2 and 3 for the weekend.
NOTE: If you wish to use only 2 periods, use the following combinations: “1 and 4” or “2 and 3”. Early Start
(see page 9) will not work with any other combinations.
You can have a different program every day; i.e., each period can start at a different time every day. The
thermostat has been programmed with the following schedule.
Default schedule
Period Description Setting MO TU WE TH FR SA SU
Wake Comfort 6:00 6:00 6:00 6:00 6:00 6:00 6:00
Leave Economy 8:30 8:30 8:30 8:30 8:30 --:-- --:--
Return Comfort 17:00 17:00 17:00 17:00 17:00 --:-- --:--
Sleep Economy 23:00 23:00 23:00 23:00 23:00 23:00 23:00
TH115-AF-GA / TH115-AF-GB
15
ENGLISH
Press Pgm. Period 1 for Monday is displayed.
To program another period, press Pgm to display that period.
To program another day, press Day to display that day (hold for 3 seconds to
select the entire week).
Press Hour and Min to set the period start time, or press Clear to skip
(cancel) the period (--:-- will be displayed).
Repeat steps 2 to 4 to program another period.
Press Mode/Ret to return the thermostat to normal display.
NOTE: The thermostat will automatically return to normal display if no button is
pressed for 60 seconds.
Modifying the schedule
Owner’s Guide
16
ENGLISH
In Automatic mode, the thermostat follows the programmed schedule (see
page 14). To place the thermostat in this mode, press Mode/Ret until is
displayed.
If you modify the setpoint temperature (by pressing the , or button) when
the thermostat is in Automatic mode, the new temperature will be used until the
beginning of the next period. flashes during the temporary override. You can
cancel the temporary override by pressing Mode/Ret.
Running the schedule (Automatic mode)
Temporary override of schedule
TH115-AF-GA / TH115-AF-GB
17
ENGLISH
To place the thermostat in Manual mode, press Mode/Ret to display on the screen. In this mode, the
thermostat does not follow the programmed schedule. Press the , or button to set the
temperature.
In this mode, the thermostat uses the vacation preset temperature (see page 13). There are two ways to
place the thermostat in Vacation mode:
Press the button on the thermostat. When the Vacation mode is activated this way, the icon
appears on the screen without flashing.
From any remote control device equipped with a dry contact. When the contact closes, the thermo-
stat is placed in Vacation mode and the icon flashes on the screen. All buttons on the thermostat
are locked. When the contact opens, the thermostat returns to the previous mode.
NOTE: When the Vacation mode is activated from a remote control device, it can only be deacti-
vated using the device.
Permanent override of schedule (Manual mode)
When you go on vacation (Vacation mode)
Owner’s Guide
18
ENGLISH
This ground fault protection thermostat is different from conventional thermostats. In the event of a ground
fault, the ground fault protection mechanism on the thermostat will trip and quickly stop the flow of
electricity to prevent serious injury.
Definition of a ground fault
Instead of following its normal safe path, electricity passes through a person’s body to reach the ground.
For example, a defective floor heating mat can cause a ground fault.
A ground fault protection thermostat does not protect against circuit overloads, short circuits, or
electrical shocks. For example, you can still receive an electrical shock if you touch bare wires while
standing on a non-conducting surface such as a wood floor.
Ground fault protection reset
When the ground fault protection mechanism trips, the TEST light is On (red). To reset the ground fault
protection, switch the thermostat to Off and back to On. The TEST light will turn off.
End of Life
If the TEST light is flashing permanently the device must be replaced.
Ground fault protection (GFCI)
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76

Aube TH115-AF-GA Le manuel du propriétaire

Catégorie
Thermostats
Taper
Le manuel du propriétaire