Toro Flex-Force Power System 60V MAX 22in Recycler Lawn Mower Manuel utilisateur

Form No. 3465-412 Rev A

Flex-Force Power System™ 60V MAX 22in Recycler

®

Lawn Mower

21469

Cortacésped Recycler

®

60V MAX de 56 cm (22") con

Flex-Force Power System™

21469

T ondeuse Recycler

®

60 V MAX 56 cm (22 po) avec

Flex-Force Power System™

21469

www .T oro.com.

*3465-412*

Form No. 3465-409 Rev A

Flex-Force Power System

™

60V

MAX 22in Recycler

®

Lawn Mower

Model No. 21469 —Serial No. 400000000 and Up

Register at www .T oro.com.

Original Instructions (EN)

*3465-409*

For assistance, please see

www .T oro.com/support

for instructional videos

or contact 1-888-384-9939

before returning this

product.

W ARNING

CALIFORNIA

Proposition 65 W arning

The power cord on this product contains

lead, a chemical known to the State

of California to cause birth defects

or other reproductive harm. W ash

hands after handling.

Use of this product may cause exposure

to chemicals known to the State of

California to cause cancer , birth defects,

or other reproductive harm.

Introduction

This rotary-blade, walk-behind lawn mower is intended

to be used by residential homeowners. It is designed

primarily for cutting grass on well-maintained lawns

on residential properties. It is not designed for cutting

brush or for agricultural uses. It is designed to use

Flex-Force 60V lithium-ion battery packs. These

battery packs are designed to be charged only by

Flex-Force 60V lithium-ion battery chargers. Using

these products for purposes other than their intended

use could prove dangerous to you and bystanders.

Read this information carefully to learn how to operate

and maintain your product properly and to avoid

injury and product damage. Y ou are responsible for

operating the product properly and safely .

V isit www .T oro.com for more information, including

safety tips, training materials, accessory information,

help nding a dealer , or to register your product.

Whenever you need service, genuine T oro parts, or

additional information, contact an Authorized Service

Dealer or T oro Customer Service and have the model

and serial numbers of your product ready . Figure 1

identies the location of the model and serial numbers

on the product. W rite the numbers in the space

provided.

Important: W ith your mobile device, you can

scan the QR code on the serial number decal (if

equipped) to access warranty , parts, and other

product information.

g275230

Figure 1

1. Model and serial number location

Model No.

Serial No.

Safety-Alert Symbol

The safety-alert symbol ( Figure 2 ) shown in this

manual and on the machine identies important safety

messages that you must follow to prevent accidents.

g000502

Figure 2

Safety-alert symbol

The safety-alert symbol appears above information

that alerts you to unsafe actions or situations and

is followed by the word DANGER ,W ARNING , or

CAUTION .

DANGER indicates an imminently hazardous situation

which, if not avoided, will result in death or serious

injury .

W ARNING indicates a potentially hazardous situation

which, if not avoided, could result in death or serious

injury .

CAUTION indicates a potentially hazardous situation

which, if not avoided, may result in minor or moderate

injury .

This manual uses two other words to highlight

information. Important calls attention to special

mechanical information and Note emphasizes general

information worthy of special attention.

81 1 1 L yndale A venue South

Bloomington, MN 55420

2

Contact us at www .T oro.com.

Printed in Mexico

Safety

IMPORT ANT SAFETY

INSTRUCTIONS

W ARNING

When using electric lawn mowers, basic

safety precautions should always be followed

to reduce the risk of re, electric shock, and

personal injury , including the following:

Read All Instructions

I. T raining

1. The operator of the machine is responsible for

any accidents or hazards occurring to others or

their property .

2. Do not allow children to use or play with the

machine, battery pack, or the battery charger;

local regulations may restrict the age of the

operator .

3. Do not allow children or untrained people to

operate or service this machine. Allow only

people who are responsible, trained, familiar

with the instructions, and physically capable to

operate or service the machine.

4. Before using the machine, battery pack, and

battery charger , read all the instructions and

cautionary markings on these products.

5. Become familiar with the controls and proper

use of the machine, battery pack, and battery

charger .

II. Preparation

1. Keep bystanders, especially children and pets,

out of the operating area.

2. Do not operate the machine without all guards

and safety devices, such as deectors and grass

catchers, in place and functioning properly on

the machine.

3. Inspect the area where you will use the machine

and remove all objects that could interfere with

the operation of the machine or that the machine

could throw .

4. Before using the machine, ensure that the blade,

blade bolt, and blade assembly are not worn or

damaged. Replace any damaged or unreadable

labels.

5. Use only the battery pack specied by T oro.

Using other accessories and attachments may

increase the risk of injury and re.

6. Plugging the battery charger into an outlet that is

not 120V can cause a re or electric shock. Do

not plug the battery charger into an outlet other

than 120V . For a dif ferent style of connection,

use an attachment plug adapter of the proper

conguration for the power outlet if needed.

7. Do not use a damaged or modied battery

pack or battery charger , which may exhibit

unpredictable behavior that results in re,

explosion, or risk of injury .

8. If the supply cord to the battery charger is

damaged, contact an Authorized Service Dealer

to replace it.

9. Charge the battery pack with only the battery

charger specied by T oro. A charger suitable for

1 type of battery pack may create a risk of re

when used with another battery pack.

10. Charge the battery pack in a well-ventilated area

only .

1 1. Follow all charging instructions and do

not charge the battery pack outside of the

temperature range specied in the instructions.

Otherwise, you may damage the battery pack

and increase the risk of re.

12. Dress properly—W ear appropriate clothing,

including eye protection; long pants; substantial,

slip-resistant footwear (not barefoot or wearing

sandals); and hearing protection. T ie back long

hair and do not wear loose clothing or loose

jewelry that can get caught in moving parts.

W ear a dust mask in dusty operating conditions.

Use of rubber gloves is recommended.

III. Operation

1. Contact with the moving blade will cause serious

injury . Keep your hands and feet away from the

cutting area and all moving parts of the machine.

Keep clear of any discharge opening.

2. Using this machine for purposes other than its

intended use could prove dangerous to you and

bystanders.

3. Disengage the self-propel drive (if equipped)

before starting the machine.

4. Do not tilt the machine when starting the motor .

5. Prevent unintentional starting—Ensure that

the electric-start button is removed from the

electric-start switch before connecting the

battery pack and handling the machine.

6. Use your full attention while operating the

machine. Do not engage in any activity that

causes distractions; otherwise, injury or property

damage may occur .

7. Stop the machine, remove the electric-start

button, remove the battery pack from the

machine, and wait for all movement to stop

before adjusting, servicing, cleaning, or storing

the machine.

3

8. Remove the battery pack and electric-start

button from the machine whenever you leave it

unattended or before changing accessories.

9. Do not force the machine—Allow the machine to

do the job better and safer at the rate for which it

was designed.

10. Stay alert—W atch what you are doing and use

common sense when operating the machine.

Do not use the machine while ill, tired, or under

the inuence of alcohol or drugs.

1 1. Do not use a battery-operated lawn mower in

rain.

12. Operate the machine only in good visibility and

appropriate weather conditions. Do not operate

the machine when there is the risk of lightning.

13. Use extreme caution when reversing or pulling

the machine toward you.

14. Keep proper footing and balance at all times,

especially on slopes. Mow across the face

of slopes, never up and down. Use extreme

caution when changing directions on slopes. Do

not mow exceedingly steep slopes. W alk, never

run with the machine.

15. Do not direct the discharge material toward

anyone. A void discharging material against a

wall or obstruction; material may ricochet toward

you. Stop the blade(s) when crossing surfaces

other than grass.

16. W atch for holes, ruts, bumps, rocks, or other

hidden objects. Uneven terrain could cause you

to lose your balance or footing.

17. W et grass or leaves can cause serious injury if

you slip and contact the blade. Do not mow in

wet conditions. Do not mow when it is raining.

18. If the machine strikes an object or starts to

vibrate, immediately shut of f the machine,

remove the electric-start button, remove the

battery pack, and wait for all movement to stop

before examining the machine for damage.

Make all necessary repairs before resuming

operation.

19. Stop the machine and remove the electric-start

button before loading the machine for hauling.

20. Under abusive conditions, the battery pack may

eject liquid; avoid contact. If you accidently

come into contact with the liquid, ush with

water . If the liquid contacts your eyes, seek

medical help. Liquid ejected from the battery

pack may cause irritation or burns.

IV . Maintenance and Storage

1. Stop the machine, remove the electric-start

button, remove the battery pack from the

machine, and wait for all movement to stop

before adjusting, servicing, cleaning, or storing

the machine.

2. Do not attempt to repair the machine except as

indicated in the instructions. Have an Authorized

Service Dealer perform service on the machine

using identical replacement parts.

3. W ear gloves and eye protection when servicing

the machine.

4. Sharpen a dull blade on both edges to maintain

balance. Clean the blade and ensure that it is

balanced.

5. Replace the blade if it is bent, worn, or cracked.

An unbalanced blade causes vibration, which

could damage the motor or cause personal

injury .

6. When servicing the blade, be aware that the

blade can still move even though the power

source is of f.

7. Check the grass collection bag frequently for

deterioration or wear , and replace a worn bag

with a T oro [replacement] bag.

8. For best performance, use only genuine T oro

replacement parts and accessories. Other

replacement parts and accessories could be

dangerous, and such use could void the product

warranty .

9. Maintain the machine—Keep cutting edges

sharp and clean for the best and safest

performance. Keep handles dry , clean, and free

from oil and grease. Keep guards in place and in

working order . Keep blades sharp. Use identical

replacement blades only .

10. Check the machine for damaged parts—If there

are damaged guards or other parts, determine

whether the machine will operate properly .

Check for misaligned and binding moving parts,

broken parts, mounting, and any other condition

that may af fect its operation. Unless indicated

in the instructions, have an Authorized Service

Dealer repair or replace a damaged guard or

part.

1 1. When the battery pack is not in use, keep it

away from metal objects such as paper clips,

coins, keys, nails, and screws that can make a

connection from 1 terminal to another . Shorting

the battery terminals may cause burns or a re.

12. Check the blade and motor mounting bolts

frequently for tightness.

4

13. When you are not using the machine, store it

indoors in a dry , secure place out of the reach

of children.

14. Do not expose a battery pack or machine to re

or excessive temperature. Exposure to re or

temperature above 130°C (265°F) may cause

explosion.

15. CAUTION—A mistreated battery pack may

present a risk of re, explosion, or chemical

burn.

•Do not disassemble the battery pack.

•Replace the battery pack with a genuine

Flex-Force 60V lithium-ion battery pack

only; using another type of battery pack may

cause a re or risk of injury .

•Keep battery packs out of the reach of

children and in the original packaging until

you are ready to use them.

SA VE THESE

INSTRUCTIONS

Safety and Instructional Decals

Safety decals and instructions are easily visible to the operator and are located near any area

of potential danger . Replace any decal that is damaged or missing.

decal94-8072

94-8072

decal133-8054

133-8054

decal140-1324

140-1324

1. Read the Operator ’ s

Manual .

3. T o shut of f the machine,

release the bar .

2. T o start the machine,

squeeze the bar to the

handle and press the

button.

decal140-1328

140-1328

1. W arning—read the

Operator ’ s Manual .

4. Thrown object

hazard—keep bystanders

away; shut of f the engine

and wait for all moving

parts to stop before

leaving the machine; pick

up debris before mowing.

2. Cutting/dismemberment

hazard of the hand, mower

blade—stay away from

moving parts; keep all

guards and shields in

place.

5. Cutting/dismemberment

hazard of the foot, mower

blade—do not mow up

or down slopes; only

mow across slopes; look

behind you when mowing

in reverse.

3. Cutting/dismemberment

hazard of the hand, mower

blade—remove the key

and read the Operator ’ s

Manual before performing

maintenance.

5

decal125-5026

125-5026

1. Recycling mode 2. Bagging mode

decal139-8986

139-8986

Model 88980

decal161-3752

161-3752

1. Read the Operator ’ s

Manual .

4. Keep away from open re

or ames

2. Recycle the battery 5. Do not expose to rain

3. Do not dispose improperly 6. Electrical shock hazard

decal161-3763

161-3763

1. Battery charge status

6

Model 88602

decal137-9462

137-9462

decal137-9463

137-9463

1. The battery pack is charging.

2. The battery pack is fully charged.

3. The battery pack is over or under the appropriate temperature range.

4. Battery pack charging fault

7

Setup

Important: The battery pack is not fully charged

when it is purchased. Before using the machine

for the rst time, refer to Charging the Battery

Pack ( page 17 ) .

1

Mounting the Battery

Charger (Optional)

No Parts Required

Procedure

If desired, mount the battery charger securely on a

wall using the wall-mount key holes on the back of

the charger .

Mount it indoors (such as a garage or other dry place),

near a power outlet, and out of the reach of children.

Refer to Figure 3 for assistance in mounting the

charger .

Slide the charger over the appropriately positioned

hardware to secure the charger in place (hardware

not included).

g290534

Figure 3

8

2

Unfolding the Handle

No Parts Required

Procedure

W ARNING

Folding or unfolding the handle improperly can damage the cables, causing an unsafe

operating condition.

• Do not damage the cable(s) when folding or unfolding the handle.

• Ensure that the cable(s) are routed to the outside of the handle.

• If a cable is damaged, contact an Authorized Service Dealer .

Note: Ensure that the cables are routed on the outside of the handle and are not pinched (D of Figure 4 ).

g335466

Figure 4

9

3

Assembling the Grass Bag

No Parts Required

Procedure

g334351

Figure 5

10

Product Overview

g436946

Figure 6

1. Handle

7. Cutting-height lever (4)

2. Self-propel drive bar

8. Bag-on-demand lever

3. Blade-control bar

9. Handle lever (2)

4. Electric-start button

10. Grass bag

5. Electric-start switch

1 1. Rear deector

6. Battery compartment

g456273

Figure 7

1. Battery charger model

88602

2. Battery pack model 88980

Specications

Battery Pack

Model 88980

8.0 AhBattery pack capacity

432 Wh

Battery manufacturer rating = 60V maximum and 54V nominal.

Actual voltage varies with load.

Battery Charger

Model 88602

T ype

60V MAX Lithium-Ion Battery Charger

Input

120V AC ~2.0A, 60Hz

Output 60V DC 2.0A MAX

Appropriate T emperature Ranges

Charge/store the battery pack

at

5°C (41°F) to 40°C (104°F)*

Use the battery pack at

-30°C (-22°F) to 49°C (120°F)*

Use the machine at

0°C (32°F) to 49°C (120°F)*

*Charging time will increase if you do not charge the

battery pack within this range.

Store the machine, battery pack, and battery charger

in an enclosed clean, dry area.

Attachments/Accessories

A selection of T oro approved attachments and

accessories is available for use with the machine

to enhance and expand its capabilities. Contact

your Authorized Service Dealer or authorized T oro

distributor or go to www .T oro.com for a list of all

approved attachments and accessories.

T o ensure optimum performance and continued safety

certication of the machine, use only genuine T oro

replacement parts and accessories. Replacement

parts and accessories made by other manufacturers

could be dangerous.

1 1

Operation

Before Operation

Installing the Battery Pack

Important: Use the battery pack only in temperatures that are within the appropriate range; refer

to Specications ( page 1 1 ) .

1. Ensure that the vents on the battery are clear of any dust and debris.

2. Press down on the battery-compartment lid to open it (A of Figure 8 ).

3. Line up the cavity in the battery pack with the tongue on the machine and slide the battery pack into the

compartment until it locks into place (B of Figure 8 ).

4. Press down on the battery-compartment lid until it clicks into place (C of Figure 8 ).

Note: If the battery-compartment lid does not close completely , the battery is not fully installed.

g459227

Figure 8

Adjusting the Handle Height

Y ou may raise or lower the handle to a position comfortable for you.

T o adjust the handle height, do the following:

1. On both sides of the machine, rotate the handle locks (A of Figure 9 ).

2. Adjust the position of the handle to the upper (high handle height) or lower (lower handle height) position

(B of Figure 9 ).

3. When the handle is in the desired position, rotate the handle locks back until the pin clicks to secure the

handle (C of Figure 9 ).

g456084

Figure 9

1. Low handle height 2. High handle height

12

Adjusting the Cutting Height

DANGER

Adjusting the height-of-cut could bring your hands into contact with a moving blade and

result in serious injury .

• Shut off the motor , remove the battery , and wait for all moving parts to stop before adjusting

the cutting height.

• Do not put your ngers under the housing when adjusting the cutting height.

Adjust the cutting height as desired. Set all wheels to the same cutting height ( Figure 10 ).

g455806

Figure 10

13

During Operation

Starting the Machine

1. Ensure that the battery pack is installed in the machine; refer to Installing the Battery Pack ( page 12 ) .

Note: If the battery-compartment lid does not close completely , the battery is not fully installed.

2. Insert the electric-start button into the electric-start switch (A of Figure 1 1 ).

3. Squeeze the blade-control bar and hold it to the handle (B of Figure 1 1 ).

4. Press the electric-start button and keep it pressed until the motor starts (C of Figure 1 1 ).

g370586

Figure 1 1

Using the Self-Propel Drive

Simply walk with your hands on the upper handle and your elbows at your sides, and the machine will

automatically keep pace with you ( Figure 12 ).

g334136

Figure 12

Note: If the machine does not freely roll backward after self-propelling, stop walking, hold your hands in place,

and allow the machine to roll a couple of centimeters (inches) forward to disengage the wheel drive. Y ou can

also try reaching just under the upper handle to the metal handle and pushing the machine forward a couple of

centimeters (inches). If the machine still does not roll backward easily , contact an Authorized Service Dealer .

Recycling the Clippings

Y our machine comes from the factory ready to recycle the grass and leaf clippings back into the lawn.

If the grass bag is on the machine and the bag-on-demand lever is in the bagging position, move the lever to the

recycling position; refer to Operating the Bag-on-Demand Lever ( page 15 ) .

14

Bagging the Clippings

Use the grass bag when you want to collect grass and leaf clippings from the lawn.

If the bag-on-demand lever is in the recycling position, move it to the bagging position; refer to Operating the

Bag-on-Demand Lever ( page 15 ) .

Installing the Grass Bag

1. Raise and hold up the rear deector (A of Figure 13 ).

2. Install the grass bag, ensuring that the pins on the bag rest in the notches on the handle (B of Figure 13 ).

3. Lower the rear deector .

g334207

Figure 13

Removing the Grass Bag

T o remove the bag, reverse the steps in Installing the Grass Bag ( page 15 ) .

Operating the

Bag-on-Demand Lever

The bag-on-demand feature allows you to either

collect or recycle grass and leaf clippings while the

grass bag is attached to the machine.

•T o bag the grass and leaf clippings , press the

button on the bag-on-demand lever and move the

lever forward until the button on the lever pops up

(Figure 14 ).

g251583

Figure 14

1. Bag-on-demand lever (in

the recycling position)

2. Bag-on-demand lever (in

the bagging position)

•T o recycle the grass and leaf clippings , press

the button on the lever and move the lever

rearward until the button on the lever pops up.

Important: For proper operation, remove

any grass clippings and debris from the

bag-on-demand door and the surrounding

opening ( Figure 15 ) before you move the

bag-on-demand lever from 1 position to

another .

g251584

Figure 15

1. Clean here

15

Shutting Off the Machine

1. Release the blade-control bar (A of Figure 16 ).

2. Remove the electric-start button from the

electric-start switch (B of Figure 16 ).

3. Remove the battery pack; refer to Removing the

Battery Pack from the Machine ( page 16 ) .

Note: Whenever you are not using the machine,

remove the battery pack.

g370557

Figure 16

Removing the Battery Pack

from the Machine

1. Lift up the battery-compartment lid.

2. Press the battery-pack latch to release the

battery pack and remove the battery pack.

3. Close the battery-compartment lid.

Operating T ips

General Mowing T ips

•Inspect the area where you will use the machine

and remove all objects that the machine could

throw .

•A void striking solid objects with the blade. Never

deliberately mow over any object.

•If the machine strikes an object or starts to vibrate,

immediately shut of f the machine, wait for all

moving parts to stop, remove the battery pack

from the machine, and examine the machine for

damage.

•For best performance, install a new T oro blade

before the cutting season begins or when

necessary .

Cutting Grass

•Cut only about a third of the grass blade at a time.

For improved quality of cut, runtime, and bagging,

cut grass at a higher height of cut.

•Do not cut below 51 mm (2 inches) unless the

grass is sparse or it is late fall when grass growth

begins to slow down.

•When cutting grass over 15 cm (6 inches) tall,

mow at the highest cutting height setting and walk

slower; then mow again at a lower setting for the

best lawn appearance. If the grass is too long, the

machine may plug and cause the motor to stall.

•W et grass and leaves tend to clump on the yard

and can cause the machine to plug or the motor to

stall. A void mowing in wet conditions.

•Be aware of a potential re hazard in very dry

conditions, follow all local re warnings, and keep

the machine free of dry grass and leaf debris.

•Alternate the mowing direction. This helps

disperse the clippings over the lawn for even

fertilization.

•If the nished lawn appearance is unsatisfactory ,

try 1 or more of the following:

– Replace the blade or have it sharpened.

– W alk at a slower pace while mowing.

– Raise the cutting height on your machine.

– Cut the grass more frequently .

– Overlap cutting swaths instead of cutting a full

swath with each pass.

Cutting Leaves

•After cutting the lawn, ensure that half of the lawn

shows through the cut leaf cover . Y ou may need

to make more than a single pass over the leaves.

16

•If there are more than 13 cm (5 inches) of leaves

on the lawn, mow at a higher cutting height and

then again at the desired cutting height.

•Slow down your mowing speed if the machine

does not cut the leaves nely enough.

After Operation

Charging the Battery Pack

Important: The battery pack is not fully charged

when you purchase it. Before using the tool for

the rst time, place the battery pack in the charger

and charge it until the LED display indicates the

battery pack is fully charged. Read all safety

precautions.

Important: Charge the battery pack only in

temperatures that are within the appropriate

range; refer to Specications ( page 1 1 ) .

Note: At any time, press the battery-charge-indicator

button on the battery pack to display the current

charge (LED indicators).

1. Ensure that the vents and charging terminals on

the battery pack and charger are clear of any

dust and debris.

g459228

Figure 17

1. Battery pack cavity

5. LED indicators (current

charge)

2. Battery pack venting areas 6. Handle

3. Battery pack terminals

7. Charger LED indicator

light

4. Battery-charge-indicator

button

8. Charger venting areas

2. Line up the cavity in the battery pack ( Figure 17 )

with the tongue on the charger .

3. Slide the battery pack into the charger until it is

fully seated ( Figure 17 ).

4. T o remove the battery pack, slide the battery

backward out of the charger .

17

5. Refer to the following table to interpret the LED

indicator light on the battery charger .

Indicator

light

Indicates

Of f

No battery pack inserted

Green

blinking

Battery pack is charging

Green

Battery pack is charged

Red

Battery pack and/or battery charger is over or under

the appropriate temperature range

Red

blinking

Battery pack charging fault*

*Refer to T roubleshooting ( page 23 ) for more

information.

Important: The battery pack can be left on the

charger for short periods between uses.

If the battery pack will not be used for longer

periods, remove the battery pack from the

charger; refer to Storage ( page 22 ) .

Cleaning Under the

Machine

Service Interval : After each use

For best results, clean the machine soon after you

have completed mowing.

1. Move the machine onto a at paved surface.

2. Remove the electric-start button and wait for

all moving parts to stop before leaving the

operating position.

3. Remove the battery pack; refer to Removing the

Battery Pack from the Machine ( page 16 ) .

4. W ash out the area under the rear door where the

clippings go from the underside of the machine

to the grass bag.

Note: W ash out the area with the

bag-on-demand (if equipped) in both the fully

forward and fully rearward positions.

5. Start the motor and run it for a few minutes to

dry the underside of the machine to prevent it

from rusting.

6. Shut of f the motor , remove the electric-start

button, and store the machine; refer to Storage

( page 22 ) .

Cleaning Under the Machine in the

V ertical-Stow Position

1. Set the machine in the vertical-stow position;

refer to Storing the Machine in the V ertical-Stow

Position ( page 19 ) .

2. W ash out the clippings from under the machine.

Folding the Handle

W ARNING

Folding or unfolding the handle improperly can damage the cables, causing an unsafe

operating condition.

• Do not damage the cable(s) when folding or unfolding the handle.

• Ensure that the cable(s) are routed to the outside of the handle.

• If a cable is damaged, contact an Authorized Service Dealer .

1. Hold the handle while disengaging the handle locks to avoid pinching your hands.

2. Disengage the handle locks until you can move the upper handle freely (A of Figure 18 )

3. Fold the handle forward to the fully forward position (B of Figure 18 ).

Important: Route the cables to the outside of the handle locks as you fold the handle.

18

La page charge ...

Toro Flex-Force Power System 60V MAX 22in Recycler Lawn Mower Manuel utilisateur

Toro Flex-Force Power System 60V MAX 22in Recycler Lawn Mower Manuel utilisateur

dans d''autres langues

Documents connexes