Day-Brite CFI FluxPanel LED Gen2 Suspension Kit Install Instructions

Marque: Day-Brite CFI

Modèle: FluxPanel LED Gen2 Suspension Kit

Taper: Install Instructions

Ce manuel convient également à

FluxPanel LED

DETAIL A

SCALE 1 : 4

Figure 1

Figure 2

DETAIL B

SCALE 1 : 4

Cable Gripper

Retention Screw

DETAIL C

SCALE 1 : 3

1. Unpack suspension kit and make sure all parts are accounted

for. (4-suspension brackets, 8-screws, 2-cross cables, 2-steel

wires, 2-cable connectors, and 2-cable grippers)

2. Unscrew (4) T-grid hooks,

Figure 1

, and discard each hook

including the (2) screws from each.

3. Using the screws that were provided, fasten a suspension

bracket in the same location as the discarded T-grid hook.

Figure 2

4. Repeat step 3 for the remaining suspension brackets.

5. Attach (2) cross cables and cable

gripper to both ends of the luminaire by

inserting the cross cable toggles through

hanger holes on the suspension bracket

previously installed.

Figure 3

6. Lock cable grippers in place midway between hanging clips by inserting the retention screw into the bottom

of the gripper and tightening loosely. Luminaire can be leveled once it is in place by sliding cross cables to

appropriate balance point. Once luminaire is leveled tighten retention screw to lock grippers in place.

Figure 3

CAUTION: THE INSTALLATION AND SERVCING OF THIS PRODUCT SHOULD

BE PERFORMED BY A QUALIFIED ELETRICIAN OR SERVICE PERSONNAL

Suspension Kit

FPZ

442295201936

ATTENTION : L’INSTALLATION ET L’ENTRETIEN DE CE PRODUIT DOIVENT ETRE

EFFECTUÉS PAR UN ÉLECTRICIEN OU UN MEMBRE DU PERSONNEL QUALIFIÉ.

CAUTION: Electrical luminaires are designed for permanent installation in ordinary (non-hazardous) locations in accordance with the National Electrical

Code and all applicable local codes. Do not use in areas of limited ventilation or in high ambient enclosures. The lamp and luminaire operate at high

temperatures, contact with combustible materials can cause fire and personal contact can cause severe burns.

ATTENTION: Ce luminaire a été conçu pour une installation permanente dans un emplacement régulier (non dangereux) et en conformité avec le Code

électrique canadien et codes locaux applicables. Ne jamais installer dans un endroit où la ventilation est limitée ou dans des boîtiers où la température

ambiante est très élevée. La lampe et le luminaire fonctionnent à des températures élevées, un contact avec des matériaux combustibles peut engendrer un

incendie et un contact corporel peut causer de sévères brûlures

representation or warranty as to the accoracy or completeness of the information

included herein is given and any liability for any action in reliance thereon is disclaimed.

All trademarks are owned by signify holding or their respective owners.

Signify Canada Ltd.

281 Hillmount Road

Markham, ON, Canada L6C 2S3

Telephone: 800-668-9008

Signify North America Corporation

200 Franklin Square Drive

Somerset, NJ 08873

Telephone: 855-486-2216

POWER-FEED: SUSPENSION KIT

1. Attach bracket and stud to customer supplied

junction box. Attach green ground lead from cord to

ground screw on bracket.

2. Support the luminaire approximately 2' below

mounting surface. Use outer couple ring to lock canopy

to junction box. Once luminaire is supported pass end

of power cord through power feed hole in canopy.

3. Make wiring connections to cord leads.

4. Insert cable into two piece coupler ensuring that

cable terminal sits in coupler. Slide power feed canopy

over stud and screw coupler to stud. Use outer couple

ring to lock canopy to junction box.

5. Attach strain relief to cord and insert canopy

opening. Allow approximately 6" of cord above strain

relief.

NOTE: For splice inspection the canopy can be dropped

away from junction box by loosening outer coupler ring

and dropping canopy away from the ceiling.

ATTACHMENT OF CABLES TO CROSS CABLE GRIPPERS.

Bracket

Threaded Stud

Ground Screw

Canopy

Strain Relief

Coupler

Power Cord

Cable

To Fixture