Lithium Earthwise LST02212 Manuel utilisateur

Marque: Lithium Earthwise

Modèle: LST02212

Catégorie: Tondeuses à gazon

Taper: Manuel utilisateur

OPERATOR’S MANUAL

CORDLESS 20 VOLT STRING TRIMMER LITHIUM-ION BATTERY PACK

This product is covered by U.S. patents and other international patents

LST02212

Your string trimmer has been engineered and manufactured to our high standard for dependability, ease of operation,

and operator safety. Properly cared for, it will give you years of rugged, trouble-free performance.

WARNING: To reduce the risk of injury, the user must read and understand the operator’s manual before

using this product.

Thank you for your purchase.

DO NOT RETURN THIS PRODUCT TO THE STORE. OPERATING, ASSEMBLY, PARTS, SERVICE QUESTIONS?

CALL 1-800-313-5111 BETWEEN 7:30 AM—4:30 PM EST FOR ASSISTANCE.

SAVE THIS MANUAL FOR FUTURE REFERENCE

BATTERY MUST BE CHARGED BEFORE FIRST USE

GENERAL SAFETY

IMPORTANT SAFETY WARNINGS

TO REDUCE RISK OF INJURY:

Before any use, be sure everyone using this tool reads and

understands all safety instructions and other information

contained in this manual.

CAUTION: Wear appropriate personal hearing protection

during use. Under some conditions and duration of use,

noise from this product may contribute to hearing loss.

Save these instructions and review frequently prior to use and

in instructing others.

WARNING: When using electric gardening appliances, basic

safety precautions should always be followed to reduce risk of

fire, electric shock, and personal injury, including the following:

READ ALL INSTRUCTIONS

KEEP CHILDREN AWAY - All visitors, children and pets

should stay at a safe distance from the work area.

DRESS PROPERLY – Don’t wear loose clothing or

jewelry. Wear protective hair covering to contain long hair.

They can be caught in moving parts. Use of rubber gloves

and substantial footwear is recommended when working

outdoors. Always wear long pants when operating this

string trimmer.

USE SAFETY GLASSES –Wear safety glasses with side

shields or goggles that are marked to comply with ANSI

Z87.1 standard when operating this product. Use face or

dust mask if environment is dusty.

USE RIGHT APPLIANCE – Do not use an appliance for

any job except that for which it is intended.

REMOVE THE BATTERY FROM THE STRING TRIMMER

when not in use or when servicing or cleaning. Do not

leave unattended.

CHECK DAMAGED PARTS – Before further use of the

trimmer, a guard or other part that is damaged should be

carefully checked to determine that it will operate properly

and perform its intended function. Check for alignment of

moving parts, binding of moving parts, breakage of parts,

mounting and any other condition that may affect its

operation. A guard or other part that is damaged should

be properly repaired or replaced. Call our customer

service help line at 1-800-313-5111 for assistance.

LIGHTING - Only operate trimmer in daylight or good

artificial light.

DON’T OVERREACH – Keep proper footing and balance

at all times.

WARNING: Do Not use the string trimmer with any type of

accessory or attachment. Such usage might be hazardous.

AVOID DANGEROUS ENVIRONMENTS – Don’t use

trimmer in rain, damp or wet locations. Do not operate

trimmer in gaseous or explosive atmospheres. Motors in

these tools normally spark, and the sparks might ignite

fumes.

AVOID UNINTENTIONAL STARTING – Don’t carry the

string trimmer with finger on switch.

DANGER: Risk of cut. Keep hands away from the line.

Keep both hands on handles when power is on.

DO NOT ATTEMPT to remove cut material or hold material to

be cut when lines are moving. Make sure trimmer switch is off

when clearing jammed material from guard. Do not grasp the

guard or lines when picking up or holding the trimmer.

CAUTION: Lines coasts after turned off.

DON’T FORCE STRING TRIMMER – It will do the job better

and with less likelihood of a risk of injury at the rate for which it

was designed.

STAY ALERT – Watch what you are doing. Use common

sense. Do not operate string trimmer when you are tired or

under the influence of drugs, alcohol or medications.

STORE IDLE STRING TRIMMER INDOORS – When not in

use, the string trimmer should be stored indoors in a dry and

high or locked-up place, out of reach of children.

MAINTAIN TRIMMER WITH CARE – Keep clean for best

performance and to reduce the risk of injury. Inspect extension

cord periodically and replace if damaged. Keep handles dry,

clean and free from oil and grease.

WARNING: California Proposition 65: This product contains

chemicals known to the State of California to cause cancer,

birth defects or other reproductive harm.

WARNING: Some dust and debris created by this tool could

contain chemicals known to the State of California to cause

cancer, birth defects or other reproductive harm. Some

examples of these chemicals are:

-chemicals in fertilizers

-compounds in insecticides, herbicides and pesticides

-arsenic and chromium from chemically treated lumber

Your risk of exposure to these chemicals varies depending

on how often you do this type of work. To reduce your

exposure, work in a well ventilated area and with approved

safety equipment such as dust masks that are specially

designed to filter out microscopic particles.

AUXILIARY HANDLE ADJUSTMENT

For maximum comfort and control, adjust the auxiliary handle to

suit your height. Shorter users adjust handle to a lower position

(away from you) and taller users adjust handle to an upper

position (towards you). The handle should be adjusted so that

your front arm is straight.

HEIGHT ADJUSTMENT

The overall height of the trimmer can be adjusted by loosening

the locking collar. The tubes can then be extended shorter or

longer. When the desired height is achieved rotate the locking

collar back to the original tightened position.

CUTTING WIDTH ADJUSTMENT

Cutting width can be adjusted to 10” or 12” by positioning the

line cutting blade as shown.

ASSEMBLY

UNPACKING

This product requires some assembly.

PACKING LIST

String Trimmer - Safety Guard

Charger and Battery Pack—Instruction Manual

Hardware Pkg. (attached to Safety Guard)

WARNING: Do not install battery until assembly is

complete. Failure to comply could result in accidental

starting and possible serious personal injury.

WARNING: If any parts are damaged or missing do

not operate this product until the parts are replaced.

Failure to heed this warning could result in serious

personal injury.

Carefully remove the product and any accessories from

the box. Make sure that all items listed in the packing

list are included. Inspect the product carefully to make

sure no breakage or damage occurred during shipping.

Do not discard the packing material until you have

carefully inspected and satisfactorily operated the

product.

If any parts are damaged or missing, please call

1-800-313-5111 for assistance.

ATTACHING THE GUARD

Assemble the guard as shown below by sliding it over

the head of the motor housing and rotating it counter

clockwise. Using a Phillips screw driver, secure the four

(4) screws into the guard and motor housing. Remove

blade guard before use.

WARNING: Do not operate the trimmer without the

guard attached.

OPERATING

TO TURN THE TOOL ON

Push the lock button in with your thumb and then squeeze

the trigger with your fingers. (Once the tool is running, you

can release the lock button). To turn the tool OFF, release

the trigger.

Before you start the unit, make sure the trimmer is not

contacting any object.

WARNING: Stones, pieces of metal and other objects can

be thrown out at high speed by the line. The unit and

guard are designed to reduce the danger.

WARNING: To guard against injury, observe the following:

 Read instruction manual before using, save

instruction manual.

 Keep hands away from lines.

 Keep hands on handles. Don’t overreach.

If you strike or become entangled with a foreign object,

stop tool immediately, check for damage and have any

damage repaired before further operation is attempted.

Do not operate with a broken hub or spool.

Position on inside

position for 10”cut

Position on outside

position for 12”cut

Blade Guard

Proper Cutting Stance

Weight should be balanced with both feet on

solid ground.

Basic Cutting Procedure

Slowing swing trimmer side-to-side as shown.

To convert for maintenance edging, turn off the tool. Holding

the trimmer with one hand by the auxiliary handle, grasp

the collar and push in the direction of arrow and rotate the

trimmer head until it stops (half turn), release your hand,

(rotate clockwise when viewed from the switch end). The tool

is locked in the edger position. Rotate the wire edge guide

forward and down into place before edging.

To operated as a maintenance edger, position trimmer

above sidewalk as shown.

Return to trimming position by turning the tool off, push in

direction of arrow and rotating the trimmer head counter

clockwise until it stops. When using the tool in the trimmer

mode you may choose to fold the wire edge guide out of the

way.

WARNING: Do not trim near electrical wires.

LINE FEEDING

Your trimmer uses .065” (1.65mm) diameter nylon line to cut

grass and weeds quickly and easily. In time, the tip of the

nylon line will become worn and the auto feed mechanism

will automatically feed and trim a fresh length of line. The

cutting line will wear faster if the cutting is done along

sidewalks or other abrasive surfaces or heavier weeds are

being cut. The line will extend approximately ¼ in. with each

stop and start of the switch trigger until the line reaches the

length of the grass deflector blade. Do not bump unit on

ground in attempt to feed line or for any other purpose.

If your trimmer line hits sharp or abrasive objects, such as

stones, metal pieces, or concrete, the trimmer line can be

cut too short to continue trimming. In this case, you can

manually extend the line:

1. REMOVE THE BATTERY PACK.

2. Press the line-feeding button with one hand while pulling

the line out with the other.

3. Press the button repeatedly to release line to the

proper length. Each press of the button will release

approximately 1/4 inch of line. (Note: Release only

enough line to extend just beyond the blade. If too much

line is released, the blade will be unable to cut it to the

correct working length and it may become tangled on

the rotating shaft.)

4. Install the battery pack.

5. Restart the trimmer and return to normal operation.

OPERATING

WARNING: Do not allow familiarity with this type of

product to make you careless. Remember that a

careless fraction of a second is sufficient to inflict

serious injury.

Do not operate a string trimmer in a tree, on a ladder, or

on a scaffold; this is extremely dangerous.

Wear non-slip gloves for maximum grip and protection.

Cutting Instructions

CAUTION: Lines coasts after turn off.

Do not use under wet conditions.

CAUTION: Inspect area to be trimmed and remove any wire,

cord, or string-like objects which could become entangled in

the rotating line or spool. Be particularly careful to avoid any

wire which might be bent outwardly into the path of the tool,

such as barbs at the base of a chain link fence.

Line-Feeding Button

Line-Feeding

Button

Pull

CHARGING THE BATTERY PACK

SEE CHARGER MANUAL FOR COMPLETE INSTRUCTIONS

Charger and battery pack

Constant Red = Battery is charging

Constant Green = Battery is fully

charged.

Charger

Battery pack

INSTALLING AND REMOVING BATTERY PACK FROM

THE UNIT

Slide the battery pack into your tool (see picture). Ensure

the battery is securely connected to tool.

To remove battery, depress release button and slide battery

pack out of tool.

OPERATING

REWINDING SPOOL FROM BULK LINE

(USE ONLY .065” DIAMETER LINE)

Bulk line for your trimmer/edger is available at extra cost

from your local dealer. To install bulk line, follow these steps:

 Turn off the trimmer and remove the battery.

 Press the release tabs on the line spool cover as shown

in Fig. 1, and remove the cover by pulling it straight off.

Remove the spool from the tool and remove and discard

all line on the spool.

 Insert one end of the bulk line into the hole in the spool

as shown in Fig. 2.

 Hold the line in the hole and pull the rest of the line

through the slot in the spool as shown in Fig. 3.

 Snugly and evenly wind the bulk line onto the spool in

the direction of the arrow until it is nearly full.

 Insert the line end through the eyelet in the spool hub

as should in Fig. 4. Pull the line through the hole to

maintain tension while placing the spool down into the

hub with the notched side exposed.

 Press the spool down GENTLY and rotate it until you

feel it drop into place. (When in place, the spool will turn

a few degrees left and right freely.)

 Snap the spool cover back on, insert the battery and

turn the tool on. In a few seconds you’ll hear the nylon

line being cut automatically to the proper length.

REPLACING SPOOL / CLEARING JAMS AND TANGLED

LINES

From time to time, especially when cutting thick or stocky

weeds, the line feeding hub may become clogged with sap

or other material and the line will become jammed as a

result. To clear the jam, follow these steps.

- Turn off the trimmer and remove the battery.

- Press the release tabs on the line spool retainer and

remove the cover by pulling it straight off.

- Lift the spool of nylon line out of the hub and clear any

broken line or cutting debris from the spool area.

- In case of jams and tangled line, unwrap about one foot

(30cm) of line to ensure that it is undamaged. If it is OK,

rewind it and insert the line ends through the eyelets in the

spool hub. Pull the line through the hole to maintain tension

while placing the spool down in to the hub with the notched

side exposed.

- Press the spool cover down GENTLY and rotate it until you

feel it drop into place. (When in place, the spool will freely

turn a few degrees left and right.)

- Snap the spool cover back on, insert the battery and turn

the tool on. In a few seconds or less you’ll hear the line

being cut automatically to the proper length.

TROUBLESHOOTING

Call us first with questions about operating or maintaining your string trimmer

at 1.800.313.5111 between 7:30 a.m. – 4:30 p.m. Eastern Standard Time,

or send emails to earthwise@reelin.com.

CALL US FIRST !!

Charge the battery pack only with the charger provided.

Allow at least 60 minutes of charge time before initial use of

the pole saw.

Make sure the power supply is normal household voltage,

120volts, 60Hz, AC only.

The battery charger should be operated in temperatures

between 50 and 100 degrees F.

The battery should be charged in a cool, dry place.

2 to 3 initial charging/discharging cycles may be required to

achieve maximum run time/capacity.

Do not attempt to open the charger or the unit. There are no

customer serviceable parts inside. Call the customer service

help line at 1-800-313-5111 for assistance.

DO NOT incinerate battery packs even if they are severely

damaged or completely worn out. They can explode in a fire

causing injury.

Use the battery charger indoors only.

Disconnect charger from the power supply when not in use to

prevent damage to the charger during a power surge.

When fully charged, the battery can be safety stored in

temperatures down to –40° degrees F for a period of up to

four weeks, before requiring charging.

Fully charge battery pack every 90 days.

If over a period of time the battery pack quickly runs down

after a full 60 minutes charging period, a replacement battery

pack is needed.

To prevent permanent damage to the battery, never store in a

discharged condition.

WINTER STORAGE—Fully recharge before storage and then

again every 90 days.

Since the battery will not develop a memory, it does not have

to be fully discharged before recharging.

A small leakage of liquid from the battery cells may occur

under extreme usage, charging or temperature conditions.

This does not indicate a failure. However, if the outer seal is

broken and this leakage gets on your skin.

a. Wash quickly with soap and water.

b. Neutralize with a mild acid such as lemon juice or

vinegar.

c. If the battery liquid gets in your eyes, flush them with

clean water for a minimum of 10 minutes and seek

immediate medical attention.

Problem Possible Couse Possible Solution

-Unit does not Run -Battery not making contact -Check battery is fully inserted

-Tripper switch not operational -Check that lock off button is fully forward prior to moving trigger

-Battery not installed properly -Check battery installation

-Battery not charged -Check battery charging requirements

-Line won't feed

-Line tangled in spool

-Unwrap 24" of line and re-wind

-Line fails to cut off

-Line cutter in guard is damaged or missing

-Replace guard

-Battery will not charge

-Battery not inserted into charger

-Insert battery into charger until red LED appears

-Charger not plugged in -Plug charger into a working outlet

-Check current at receptacle by plugging in a lamp or other appliance

-Check to see if receptacle is connected to a light switch which turns

power off when you turn out the lights

-Surrounding air temperature too hot or too cold -Move charger and tool to a surrounding air temperature of about 50

degree F (10 degree C) or below 100 degree F (+37.8 degree c)

BATTERY DISPOSAL

Remove the battery pack from the string trimmer. Cover the terminals with heavy duty adhesive tape. Do not attempt to destroy or disassemble

battery pack or remove any components. This product contains lithium-ion batteries which must be recycled or disposed of properly. Local, state

or federal laws may prohibit disposal of these batteries in ordinary trash.

The RBRC seal on the li-ion battery pack indicates that the costs to recycle the battery pack at the end of its useful life has already

been paid by The Great States Corporation American Lawn Mower Company. It is illegal to place spent li-ion batteries in the local

municipal solid waste or in the trash. RBRC in cooperation with The Great States Corporation American Lawn Mower Company

has provided an environmentally friendly and easy way to recycle spent li-ion batteries. Just contact your local recycling center or

call 1-800-8BATTERY for information on where to drop off the spent battery.

CHARGING THE BATTERY PACK

CAUTION: Do not at any time let brake fluids, gasoline,

petroleum based products, penetrating oils, etc., come in

contact with plastic parts. They contain chemicals that can

damage, weaken or destroy plastic.

Make sure the battery is detached from the unit, then use

only mild soap and a damp cloth to clean the tool. Never let

any liquid get inside the tool; never immerse any part of the

tool into a liquid.

Fertilizers and other garden chemicals contain agents which

greatly accelerate the corrosion of metals Do not store the

tool on or adjacent to fertilizers or chemicals.

IMPORTANT: To assure product SAFETY and RELIABILITY,

repairs, maintenance and adjustment should be performed by

a qualified individual using only identical replacement parts.

If you drop the trimmer, carefully inspect it for damage. If the

guard is bent or cracked, handles broken or if you see any

other condition that may affect the trimmer’s operation, it must

be repaired before putting it back into use. Call our customer

service help line at 1-800-313-5111 for assistance.

PRODUCT SPECIFICATIONS

0.065 Single Line - Automatic Feed - Edging Function - 3 Position Adjustable Head

MAINTENANCE

FEATURES

LST02212

Input….………………………….……………………...20V, DC Only

Battery………………………………….…....20V 2.0 Ah Lithium-ion

Speed ………………………..…8500 RPM (10”)...7600RPM (12”)

Cutting Width………………………………………………10 or 12 in.

Weight ………………………………………………… 4.6 Ib. (2.1kg)

BATTERY PACK

REAR HANDLE

SAFETY LOCK-OFF BUTTON

TRIGGER SWITCH

FRONT HANDLE

(AUXILIARY HANDLE)

LOCKING COLLAR

TELESCOPIC TUBE

EDGER GUIDE

GUARD

The Great States Corporation

American Lawn Mower Company

830 Webster Street

Shelbyville, IN 46176

Phone 1-800-313-5111

www.earthwisetools.com

In a continued commitment to improve quality, the Manufacturer reserves the

right to make component changes or design changes when necessary.

WARRANTY

LIMITED WARRANTY FOR CORDLESS ELECTRIC MODELS

This product is manufactured for The Great States Corporation/American Lawn Mower Company. The Great States Corporation/American

Lawn Mower Company, Shelbyville, Indiana, has been making lawn mowers for over 100 years and warrants to the original owner that each

new product and service part is free from defects in material and workmanship and agrees to repair or replace under this warranty any defec-

tive product or part from the original date of purchase for two (2) years except for the conditions and circumstances listed below. Proof of pur-

chase (original dated sales receipt) must accompany all warranty claims.

THIS WARRANTY IS NOT TRANSFERABLE AND DOES NOT COVER:

Expendable items that become worn during normal use.

Cosmetic defects that do not interfere with tool

functionality.

Freight costs from customer to vendor.

Repair and transportation costs of products or

parts determined not to be defective.

ANY INCIDENTAL, INDIRECT, OR CONSEQUENTIAL

LOSS, DAMAGE, OR EXPENSE THAT MAY RESULT

FROM ANY DEFECT, FAILURE, OR MALFUNCTION

OF THE PRODUCT. Some states do not allow the

exclusion or limitation on how long an implied warranty

lasts, so the above limitations may not apply to you.

ANY NON-RESIDENTIAL USE OR COMMERCIAL USE

VOIDS ALL WARRANTIES.

Products sold damaged or incomplete, sold “as is”, sold

reconditioned, or used as rental equipment.

Delivery, installation, or normal adjustments explained in

the operator’s manual.

Damage or liability caused by shipping, improper

handling, improper installation, incorrect voltage or

improper wiring, improper maintenance, improper

modification, or the use of accessories and/or

attachments not specifically recommended.

Repairs necessary because of operator abuse or

negligence, or the failure to install, operate, maintain, or

store the product according to the instructions in the

operator’s manual.

Damage caused by cold, heat, rain, excessive

humidity, corrosive environments and materials,

or other contaminants.

Rev. 12/18/2015

MANUAL DEL OPERARIO

DESBROZADORA INALÁMBRICA CON PAQUETE DE BATERÍAS DE IONES DE LITIO DE 20V

Este producto está amparado por patentes de EE. UU. y otras patentes internacionales.

LST02212

Su desbrozadora fue diseñada y fabricada de acuerdo con nuestros altos estándares de confiabilidad, facilidad de operación y seguridad para el

operario. Si se la trata con cuidado, le otorgará años de óptimo rendimiento y resistencia.

ADVERTENCIA: para reducir el riesgo de sufrir alguna lesión, el usuario debe leer y comprender el manual del operario antes de

usar este producto.

Muchas gracias por su compra.

NO DEVUELVA ESTE PRODUCTO A LA TIENDA. ¿TIENE PREGUNTAS SOBRE EL FUNCIONAMIENTO, EL MONTAJE, LAS PIEZAS O EL MAN-

TENIMIENTO? Llame al 1-800-313-5111 ENTRE LAS 7:30 Y LAS 16:30 H, HORA ESTÁNDAR DEL ESTE, PARA OBTENER ASISTENCIA.

GUARDE ESTE MANUAL PARA CONSULTAS FUTURAS

DEBE CARGAR LA BATERÍA ANTES DE UTILIZARLA POR PRIMERA VEZ.

NORMAS GENERALES DE SEGURIDAD

ADVERTENCIAS DE SEGURIDAD IMPORTANTES

PARA REDUCIR EL RIESGO DE LESIONES:

Antes de poner en uso la herramienta, asegúrese de que todos los

usuarios lean y comprendan las instrucciones de seguridad y la

demás información incluida en este manual.

PRECAUCIÓN: use protección auditiva apropiada mientras trabaja.

En ciertas condiciones y con cierta duración de uso, el ruido genera-

do por este producto puede contribuir a la pérdida de la audición.

Guarde estas instrucciones y revíselas con frecuencia antes de usar la

herramienta y capacitar a otros

ADVERTENCIA: al utilizar aparatos eléctricos para el jardín, se deben

respetar siempre las precauciones de seguridad básicas que se deta-

llan a continuación, a fin de reducir riesgos de incendios, descargas

eléctricas y lesiones personales.

LEA TODAS LAS INSTRUCCIONES

MANTENGA ALEJADOS A LOS NIÑOS. Todos los visitantes,

niños y mascotas deben mantenerse a una distancia segura de la

zona de trabajo.

USE ROPA ADECUADA. No use prendas sueltas ni artículos de

joyería. Use protección para cubrir y contener el cabello largo, ya

que puede quedar atrapado en las piezas móviles. Se recomienda

usar guantes de goma y calzado resistente cuando se trabaja al

aire libre. Use siempre pantalones largos mientras opera esta

desbrozadora.

USE GAFAS DE SEGURIDAD. Al trabajar con este producto, use

gafas de seguridad con protectores laterales que cumplan con la

norma ANSI Z87.1. Si la operación genera polvo, protéjase el

rostro con una mascarilla antipolvo.

USE LA HERRAMIENTA EN FORMA CORRECTA. No utilice

esta herramienta en trabajos para los que no esté indicada.

EXTRAIGA LA BATERÍA DE LA DESBROZADORA cuando no

esté en uso o durante el mantenimiento o la limpieza. Manténgala

bajo vigilancia constante.

VERIFIQUE LAS PIEZAS DAÑADAS. Antes de seguir usando la

desbrozadora, se deberán revisar los protectores u otras piezas

dañadas en forma exhaustiva para determinar si la herramienta

funcionará correctamente y realizará el trabajo previsto. Verifique

la alineación y las uniones de las piezas móviles, el montaje, las

averías y otros factores que puedan afectar el funcionamiento. Un

protector o cualquier otra pieza dañada deben ser reemplazados

o reparados en forma adecuada. Comuníquese con nuestra línea

de ayuda de atención al cliente al 1-800-313-5111 para recibir

asistencia.

ILUMINACIÓN. Trabaje sólo con luz natural o buena luz artificial.

NO ADOPTE UNA POSTURA INCÓMODA. Mantenga una base

y equilibro apropiados en todo momento.

ADVERTENCIA: no aplique ninguna clase de accesorio o disposi-

tivo de sujeción a la desbrozadora. Dicha práctica podría resultar

peligrosa.

EVITE AMBIENTES PELIGROSOS. No utilice esta herramienta

en la lluvia ni en lugares húmedos o mojados. Tampoco trabaje

en entornos donde existan gases o sustancias explosivas. Por lo

general, los motores de estas herramientas producen chispas que

podrían inflamar los gases.

EVITE EL ENCENDIDO ACCIDENTAL. No transporte la desbro-

zadora con el dedo en el interruptor.

PELIGRO: riesgo de corte. Mantenga las manos alejadas de los

hilos. Mantenga ambas manos en los mangos mientras la herra-

mienta está encendida.

NO INTENTE extraer el material cortado ni sostener el material que

desea cortar mientras los hilos están en movimiento. Asegúrese de que

el interruptor esté en posición de apagado para luego retirar el material

atascado en el protector. No tome la desbrozadora por los hilos al tratar

de levantar o sostener la herramienta.

PRECAUCIÓN: los hilos se mueven por inercia después de apagar el

motor.

NO FUERCE LA DESBROZADORA. Realizará mejor el trabajo con

menor probabilidad de lesiones si maneja la desbrozadora a la

velocidad para la que fue diseñada.

PONGA ATENCIÓN. Observe lo que está haciendo. Use el sentido

común. No opere la desbrozadora si está cansado o bajo la influencia

de medicamentos, drogas o alcohol.

GUARDE LA DESBROZADORA BAJO TECHO. Cuando no esté en

uso, la desbrozadora se deberá guardar en un lugar cerrado, seco y

elevado y fuera del alcance de los niños.

MANTENGA LA HERRAMIENTA EN CONDICIONES. El protector y

los mangos deben estar limpios para lograr un óptimo funcionamiento y

reducir el riesgo de lesiones. Mantenga los mangos secos y libres de

grasa y aceite.

ADVERTENCIA: disposición 65 del estado de California: Este producto

contiene químicos reconocidos por el Estado de California como cau-

santes de cáncer, defectos de nacimiento u otros efectos nocivos para

el aparato reproductor.

ADVERTENCIA: parte del polvo generado por este producto podría

contener químicos reconocidos por el Estado de California como cau-

santes de cáncer y defectos de nacimiento u otros efectos nocivos para

el aparato reproductor. Algunos ejemplos de estos productos químicos

son:

-químicos presentes en fertilizantes

-compuestos presentes en insecticidas, herbicidas y pesticidas

-arsénico y cromo de maderas tratadas químicamente

El riesgo que usted corre al exponerse a estos químicos varía según la

frecuencia con la que realiza este tipo de trabajo. Para reducir la expo-

sición a estos químicos, use equipo de protección aprobado, como

mascarillas antipolvo que están especialmente elaboradas para elimi-

nar partículas microscópicas mediante un proceso de filtrado.

AJUSTE DEL MANGO AUXILIAR

Para obtener una mayor comodidad y control, regule el mango auxiliar

de acuerdo a su altura. Los usuarios de menor estatura ajustan el man-

go en una posición inferior (lejos del cuerpo) y los de mayor estatura

lo ajustan en una posición superior (hacia el cuerpo). El mango se debe

ajustar de tal modo que el brazo de adelante quede extendido.

AJUSTE DE LA ALTURA

Para regular la altura total de la desbrozadora, afloje el collar de

fijación. Luego puede acortar o extender los tubos. Una vez que

logra la altura deseada, gire el anillo de fijación de nuevo a la posición

original apretados.

AJUSTE DEL ANCHO DE CORTE

El ancho de corte puede ajustarse a 25,4 o 30,5 cm (10 o 12 pulg.)

ubicando la cuchilla del hilo como se muestra.

MONTAJE

DESEMBALAJE

Este producto requiere algunas operaciones de montaje.

LISTA DE EMBALAJE

Desbrozadora - Protector de seguridad - Cargador y paquete

de baterías - Paquete de ferretería (adjunto al protector de se-

guridad)

ADVERTENCIA: no instale la batería hasta haber completado

el montaje. De lo contrario, la máquina podría arrancar

accidentalmente y provocar lesiones personales de gravedad.

ADVERTENCIA: si alguna pieza falta o está dañada, no utilice

este producto hasta reponer la pieza en cuestión. De lo contra-

rio, podría sufrir lesiones corporales serias.

Extraiga el producto y los accesorios de la caja con

cuidado. Asegúrese de que estén incluidos todos los

elementos detallados en la lista de embalaje. Inspeccione

el producto detenidamente para corroborar que no

existan roturas ni averías ocurridas durante el envío.

No deseche el material de embalaje hasta haber inspeccionado

exhaustivamente el producto y comprobado que funciona en

forma satisfactoria.

Si alguna pieza falta o está dañada, llame al 1-800-313-5111

para obtener asistencia.

COLOCACIÓN DEL PROTECTOR

Monte el protector como se muestra a continuación, deslícelo

sobre el cabezal de la caja del motor y gírelo en sentido

contrario a las agujas del reloj. Utilice un destornillador Phillips

para ajustar los cuatro (4) tornillos en el protector y la caja del

motor. Retire el protector de la hoja antes de su uso.

ADVERTENCIA: no utilice la desbrozadora si el protector no

está colocado.

FUNCIONAMIENTO

ENCENDIDO DE LA HERRAMIENTA

Presione el botón de bloqueo con el dedo pulgar y luego

apriete el gatillo con los dedos. (Una vez que la herramienta

está en marcha, puede soltar el botón de bloqueo). Para

apagar la máquina, suelte el gatillo.

Before you start the unit, make sure the trimmer is not

contacting any object.

ADVERTENCIA: el hilo puede lanzar piedras, trozos de metal

y otros objetos a gran velocidad. La unidad y el protector es-

tán diseñados para reducir este peligro.

ADVERTENCIA: para prevenir lesiones personales, tenga en

cuenta las siguientes recomendaciones:

 Lea el manual de instrucciones antes de usar el

producto y guárdelo para consultas futuras.

 Mantenga las manos alejadas de los hilos.

 Sostenga la herramienta con ambas manos en

los mangos. No adopte una postura incómoda.

Si la herramienta se golpea o se enreda con algún objeto

extraño, deténgala de inmediato y verifique si hay daños; en

ese caso, hágala reparar antes de usarla nuevamente. No

utilice la desbrozadora si el eje o el carrete están rotos.

Ubíquela en la posición

interna para lograr un

corte de 25,4 cm

(10 pulg.)

Ubíquela en la posición

externa para lograr un

corte de 30,5 cm

(12 pulg.)

Protector de la cuchilla

Posición de corte correcta

El peso debe estar equilibrado, con ambos pies apo-

yados en suelo firme.

Procedimiento básico de corte

Desplace la desbrozadora de lado a lado lentamente

como se muestra en la ilustración.

Si desea transformar la herramienta en una bordeadora de manteni-

miento, primero debe apagarla. Mientras sostiene la desbrozadora

con una mano, presione el botón del cabezal de la desbrozadora y

gire en sentido contrario a las agujas del reloj. De este modo, la

herramienta queda ajustada en la posición de bordeadora.

FUNCIONAMIENTO

ADVERTENCIA: no permita que la familiaridad con este tipo

de productos termine en negligencia. Recuerde que un segun-

do de descuido es suficiente para provocar una lesión seria.

No opere la desbrozadora en un árbol, en una escalera ni en

un andamio; esto es sumamente peligroso.

Use guantes antideslizantes para lograr un máximo agarre y

una protección adecuada.

Si desea volver a la posición de desbrozadora, apague la herramienta,

presione el botón y gire el cabezal en el sentido de las agujas del reloj

hasta que se detenga. Cuando usa la herramienta en el modo de des-

brozadora, puede elegir plegar la guía del borde de alambre hacia

arriba para que no estorbe.

ADVERTENCIA: no corte cerca de cableados eléctricos ni de

edificaciones.

AVANCE DEL HILO

La desbrozadora utiliza hilo de nylon de 1,65 mm (0,065 pulg.) de diá-

metro para cortar césped y malezas en forma rápida y fácil. Con el

tiempo, la punta del hilo de nylon se gasta y el mecanismo de

alimentación automática avanzará y cortará un trozo de hilo nuevo

automáticamente. El hilo de corte se desgasta con mayor rapidez si el

corte se realiza a lo largo de las aceras u otras superficies abrasivas o

si se cortan malezas más densas. El hilo avanza aproximadamente

6,3 mm (1/4 pulg.) con cada detención y arranque del gatillo del

interruptor hasta que alcanza la longitud de la cuchilla del deflector de

césped. No golpee la unidad contra el suelo al intentar avanzar el hilo o

por cualquier otro motivo.

INSTRUCCIONES DE CORTE

PRECAUCIÓN: los hilos se mueven por inercia después de apagar el motor.

No trabaje en condiciones de humedad.

PRECAUCIÓN: inspeccione el área de trabajo y elimine alambres, cables, u

objetos similares que pudieran enredarse en el hilo giratorio o en el carrete.

Sea particularmente cuidadoso con los alambres que puedan proyectarse

hacia afuera e interponerse en el recorrido de la herramienta; por ejemplo,

púas en la base de una cerca de alambre.