Harman P42i-TC Pellet Insert Le manuel du propriétaire

Marque: Harman

Modèle: P42i-TC Pellet Insert

Catégorie: Cheminées

Taper: Le manuel du propriétaire

Harman® • P42i Owner’s Manual • 2023 -___ • 03/2318742-900A

To obtain a French translation of this manual, please

contact your dealer or visit www.harmanstoves.com

Pour obtenir une traduction française de ce manuel, s’il

vous plaît contacter votre revendeur ou visitez www.

harmanstoves.com

NOTE

Owner’s Manual

Care and Operation

INSTALLER: Leave this manual with party responsible for use and operation.

OWNER: Retain this manual for future reference.

Contact your local dealer with questions on installation, operation or service.

Model(s):

P42i-TC Pellet Insert

NOTICE: SAVE THESE INSTRUCTIONS

• Donotstoreorusegasolineorotherammablevapors

and liquids in the vicinity of this or any other appliance.

• Donotoverre-Ifanyexternalpartstartstoglow,you

areoverring.Reducefeedrate.Overringwillvoid

your warranty.

• Comply with all minimum clearances to combustibles

asspecied.Failuretocomplymaycausehousere.

WARNING

Hot glass will cause burns.

• Do not touch glass until it is cooled

• NEVERallowchildrentotouchglass

• Keep children away

• CAREFULLYSUPERVISEchildreninsameroomas

stove.

• Alert children and adults to hazards of high temperatures.

High temperatures may ignite clothing or other

ammable materials.

• Keepclothing,furniture,draperiesandotherammable

materials away.

HOT SURFACES!

Glass and other surfaces are hot during

operation and cool down.

WARNING

Tested and approved for wood pellets only. Burning of

any other type of fuel voids your warranty. When burning

higher ash content pellets more frequent cleanings may

be required.

CAUTION

Check building codes prior to installation.

• InstallationMUSTcomplywithlocal,regional,stateand

national codes and regulations.

• Contactlocalbuildingorreocialsaboutrestrictions

and installation inspection requirements in your area.

CAUTION

Please read this entire manual before

installation and use of this pellet fuel-

burning room heater.

Failure to follow these instructions could

result in property damage, bodily injury

or even death.

Harman® • P42i Owner’s Manual • 2023 -___ • 03/2328742-900A

Congratulations, The Harman® P42i-TC pellet insertyou

have selected is designed to provide the utmost in safety,

reliability,andeciency.

As the owner of a new pellet stove, you’ll want to read and

carefully follow all of the instructions contained in this owner’s

manual. Pay special attention to all cautions and warnings.

This owner’s manual should be retained for future reference.

We suggest that you keep it with your other important

documents and product manuals.

YournewHarman®P42i-TCPelletInsertwillgiveyouyears

ofdurableuseandtrouble-freeenjoyment.Welcometothe

Harman® family!

Note: Cast iron is an artisan crafted material, which is

made the same way today as nearly 2000 years ago.

Due to the intrinsic primitive nature of the casting

process, part to part variation is normal and adds to the

character of a hand built cast iron appliance

Read this manual before operating this appliance.

Please retain this Owner’s Manual for future reference.

Read the Installation Manual before making any installation or nishing changes.

Listing Label Information/Location Themodelinformationregardingyourspecicstovecanbefoundonthe

rating plate usually located in the control area of the stove.

Ce poêle à granulés a été testé et peut être installé dans les maisons

préfabriquées en conformité avec OAR 814-23-9000 à 814-23-909

PRÉVENTION DES INCENDIES Respecter scrupuleusement les

instructions du constructeur pour l’installation et les consignes de

fonctionnement. Respecter les règles de sécurité en vigueur dans votre

région.

Ce poêle à bois doit inspection périodique et la réparation pour un

fonctionnement correct. Consultez le manuel du propriétaire pour plus

d’informations. Ce est contre les règlements fédéraux pour faire fonctionner

ce poêle à bois d’une manière incompatible avec les instructions

d’utilisation dans le manuel du propriétaire.

AVERTISSEMENT : POUR LES MAISONS FABRIQUES: Ne pas installer

dans une chambre. Il est impératif de prévoir une prise d’air extérieur.

L’intégrité structurale du plancher, du plafond et des murs doit être

strictement préservée.

Se reporter aux instructions du fabricant et aux réglementations spéciﬁ ques

locales concernant les précautions requises lorsque la cheminée traverse

un mur ou un plafond fabriqué en matière combustible.

Contrôler et nettoyer fréquemment tout le système d’évacuation des

fumées conformément aux recommandations du constructeur.

Utiliser un conduit de fumée type « L » ou « PL » d’un diamètre de 7,6 cm

(3”) ou de 10 cm (4”), ou bien une gaine en acier inoxydable de 10 cm (4”),

comme indiqué dans le manuel d’utilisation.

Ne pas raccorder ce poêle à un conduit

de cheminée déjà utilisé pour un autre

appareil.

À UTILISER AVEC LA GRANULE DE BOIS

SEULEMENT.

Émissions certiﬁ és EPA: 1,0 g / h

Consommation maximum: 2,36 kg/h

Caractéristiques électriques:

120 V c.a. – 60 Hz – Intensité au

démarrage 5,0 A

Intensité en fonctionnement normal 4,0 A

DANGER: Risque d’électrocution.

Débrancher l’appareil avant toute

intervention.

Pour une information plus complète, se

reporter à la notice d’utilisation.

Ne remplacer la vitre qu’avec une vitre

céramique 5 mm disponible auprès de

votre revendeur.

Garder la porte vitrée bien close

durant le fonctionnement de l’appareil.

Report #/Rapport #22-858

Tested to/Testé selon: ASTM E2779, ASTM E2515, ASTM

E1509, ULC-S628, Pellet Fuel-Burning Type, Also For Use In

Manufactured Homes. (UM) 84-HUD

“PREVENT HOUSE FIRES” Install and use only in accordance

with the manufacturer’s installation and operation instructions.

Contact local building or ﬁ re ofﬁ cials about restrictions and

installation inspection in your area.

This wood heater needs periodic inspection and repair for proper

operation. Consult the owner’s manual for further information.

It is against federal regulations to operate this wood heater in a

manner inconsistent with the operating instructions in the owner’s

manual.

Room Heater, Pellet Fuel-Burning Type, Also for Use in

Manufactured Homes

WARNING: FOR MANUFACTURED HOMES: Do not install

appliance in a sleeping room. An outside combustion air inlet must

be provided. The structural integrity of the manufactured home

ﬂ oor, ceiling and walls must be maintained.

Refer to manufacturer’s instructions and local codes for precautions

required for passing chimney through a combustible wall or ceiling.

Inspect and clean exhaust venting system frequently in

accordance with manufacturer’s instructions.

Use a 3” or 4” diameter type “L” or “PL” venting system, or 4”

stainless steel ﬂ ex as per owner’s manual.

Do not connect this unit to a chimney ﬂ ue servicing another

appliance.

FOR USE WITH PELLETIZED WOOD FUEL ONLY.

EPA Certiﬁ ed Emissions: 1.0 g/hr

Input Rating Max: 5.2 lb. fuel/hr.

Electrical Rating: 120 VAC, 60 Hz, Start 3.5 AMPS, Run 2.5 AMPS

DANGER: Risk of electrical shock. Disconnect power supply

before servicing.

For further instruction refer to owner’s manual.

Replace glass only with 5mm ceramic available from your dealer.

Keep viewing door tightly closed during operation.

DO NOT REMOVE THIS LABEL/NE PAS ENLEVER CETTE

ÉTIQUETTE

12” (305mm) Mantel

Sidewall/Mur latéral

Trim/Panneau de Moulure

MINIMUM CLEARANCES TO COMBUSTIBLE MATERIAL

Non-combustible ﬂ oor protector must extend 6” (152 mm) to the sides

and front of the unit, measured from the glass face.

ÉCARTS MINIMUM DE SÉCURITÉ

La protection de sol doit être constituée de matériau incombustible et

s’étendre de 152 mm (6”) à l’avant et sur les côtés de l’unité, mesurée

depuis la vitre (ÉTATS-UNIS).

8742-930A

A. Corps de l’insert à la paroi latérale - 305mm (12 po)

B. Corps de l’insert à 12” (305mm) Mantel - 305m (12 po)

C. Introduisez le corps de 3/4 “fascia ou couper au-dessus - 0mm (0 po)

D. Corps de l’insert au bord latéral - 203mm (8 po)

E. Protection de sol. Mesurée depuis la vitre. - 152mm (6 po)

BARCODE LABEL

Serial No.

No de série:

A. Insert Body to side wall - 12” (305 mm)

B. Insert Body to 12” (305mm) Mantel - 12” (305 mm)

C. Insert Body to 3/4” fascia or trim above - 0” (0 mm)

D. Insert Body to side trim - 8” (203 mm)

E. Floor protection. Measured from glass. - 6” (152mm)

MODEL / MODÈLE: “P42i-TC Pellet Insert”

Room Heater Pellet Fuel-Burning Type

SUITABLE FOR MOBILE-HOME INSTALLATION

This pellet burning appliance has been tested and listed for use In

Manufactured Homes In accordance with OAR 814-23-900 through 814-23-909

Date of Manufacture / Date de fabrication:

2023 2024 2025 JAN FEB MAR APR MAY JUN JUL AUG SEP OCT NOV DEC

Manufactured by / Fabriqué par: Hearth and Home Technologies 352 Mountain House Road, Halifax PA 17032

US ENVIRONMENTAL PROTECTION AGENCY

Certiﬁ ed to comply with 2020 particulate emission standards.

Certiﬁ é conforme aux normes 2020 d’émission de particules.

Made in U.S.A. of US and imported parts. / Fabriqué aux États-Unis-

d’Amérique par des pièces d’origine américaine et pièces importées.

LABELTICKET

ECO: 96780 LABEL SIZE: 11”x5.75”

PART # / REV: 8742-930A ADHESIVE: N/A

ORIGINATOR: Spidlet MATERIAL: 24 Gauge Aluminum

DATE: 03/27/23 INK: ScreenedBlackBackground

(2)SlottedHoles=.156x.25

(2)Holes=Ø.2

(4)Corners=R.062

This unit will need the addendum label that refers to the

“Wood heater needs periodic inspection” Information

352MountainHouseRoad

Halifax,PA17032

SerialNumber

ModelName

EXAMPLE

Harman® • P42i Owner’s Manual • 2023 -___ • 03/2338742-900A

Table of Contents

Safety Alert Key:

• DANGER! Indicates a hazardous situation which, if not avoided, will result in death or serious injury.

• WARNING! Indicates a hazardous situation which, if not avoided, could result in death or serious injury.

• CAUTION! Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.

• NOTICE: Used to address practices not related to personal injury.

= Contains updated information



3 Reference Materials

A. ServicePartsList ...............................18

B. LimitedLifetimeWarranty ......................... 25

C. LossofPowerAddendum ........................27

D. EmergencyManualIgnition .......................27

E. Troubleshooting ................................ 28

F. ContactInformation .............................30

1 Product Specications and Important Safety Information

A. ApplianceCertication/Specications ...............4

B. ManufacturedHomeApproval ...................... 4

C. BTU&EciencySpecications .....................4

D. ApplianceSafety ................................5

E. CaliforniaSafetyInformation .......................5

F. ClearSpace ....................................5

G. Helpful Hints .................................... 6

H. FuelSpecications ...............................6

I. EPATestSettings ................................7

J. QuickStartGuide ................................ 8

K. Frequently Asked Questions .......................9

L. CleaningPrompts,MessagesandErrors. . . . . . . . . . . . . 10

2 Maintenance and Service

A. ProperShutdownProcedure ...................... 11

B. QuickReferenceMaintenanceChart ................12

C. UnitMaintenance ...............................13

 • Daily/WeeklyMaintenance ......................13

 • MonthlyMaintenance ..........................13

 • YearlyMaintenance ...........................15

Harman® • P42i Owner’s Manual • 2023 -___ • 03/2348742-900A

1 1 Product Specic and Important Safety Information

A. Appliance Certication

NOTE: Thisinstallationmustconformtolocalcodes.Inthe

absence of local codes you must comply with the ASTM

E1509,ULC-S628 & (UM) 84-HUD

THE STRUCTURAL INTEGRITY OF THE

MANUFACTURED HOME FLOOR, WALL, AND CEILING/

ROOF MUST BE MAINTAINED.

DO NOT INSTALL IN SLEEPING ROOM.

The P42i-TC Pellet Insert is certied to

comply with 2020 EPA particulate emission

standards.

MODEL: P42i-TCPelletInsert

LABORATORY: PFS•TECO

REPORT NO. F22-858

TYPE: PelletFueledInsert/Supplementary

ForResidentialUse

STANDARD(s): ASTME2779,ASTME2515,ASTM

E1509,ULC-S628

ELECTRICAL

RATING:

120VAC,60Hz,Start4.2Amps,Run

2.8 Amps

GLASS

SPECIFICATION: 5mmmirroredceramicglass

B. Manufactured Home Approved

This appliance is approved for manufactured home

installations when not installed in a sleeping room and when

an outside combustion air inlet is provided.

The structural integrity of the manufactured home oor,

ceiling, and walls must be maintained. The appliance must

be properly grounded to the frame of the manufactured home

anduseonlylistedpelletvent,Class“PL”connectorpipe.

AHarman®OutsideAirKitmustbeinstalledinamanufactured

home installation.

WARNING

Risk of Fire! Hearth & Home Technologies disclaims any

responsibility for, and the warranty and agency listing will

be voided by the below actions.

C. BTU & Eciency Specications

EPA Certication Number: F22-858

EPA Certied Emissions: 1.0 g/hr

*LHV Tested Eciency: 84%

**HHV Tested Eciency: 79%

***EPA BTU Output: 5,637-32,782

****BTU Input 7,400 – 41,800

Vent Size: 4Inch

Hopper Capacity: 64.5lbs

Fuel Wood Pellet

NOTE: Hearth & Home Technologies, manufacturer of

this appliance, reserves the right to alter its products, their

specicationsand/orpricewithoutnotice.

* Weighted average LHV eciency using data collected

during EPA emissions test.

**Weighted average HHV eciency using data collected

during EPA emissions test.

***A range of BTU outputs based on EPA Default Eciency

and the burn rates from the low and high EPA tests.

****Based on the maximum feed rate per hour multiplied by

approximately 8600 BTU’s which is the average BTU’s from

a pound of pellets.

Thiswoodheaterhasamanufacturer-setminimumlowburn

ratethatmustnotbealtered.Itisagainstfederalregulations

to alter this setting or otherwise operate this wood heater

in a manner inconsistent with operating instructions in this

manual.

This wood heater needs periodic inspection and repair for

properoperation.Itisagainstfederalregulationstooperate

this wood heater in a manner inconsistent with operating

instructions in this manual.

DO NOT:

• Install or operate damaged appliance

• Modify appliance

• Install other than as instructed by Hearth & Home

Technologies

• Operate the appliance without fully assembling all

components

• Overre

• Install any component not approved by Hearth &

Home Technologies

• Install parts or components not listed or approved.

• Disable safety switches

Improper installation, adjustment, alteration, service or

maintenance can cause injury or property damage.

For assistance or additional information, consult a qualied

installer, service agency or your dealer.

Harman® is a registered trademark of Hearth & Home

Technologies.

This wood heater needs periodic inspection and repair for

properoperation.Itisagainstfederalregulationstooperate

this wood heater in a manner inconsistent with operating

instructions in this manual.

CAUTION

Harman® • P42i Owner’s Manual • 2023 -___ • 03/2358742-900A

NOTICE: Clearances may only be reduced by means

approvedbytheregulatoryauthorityhavingjurisdiction.

WARNING

RISK OF FIRE! Do NOT place combustible objects

in front or to the sides of the appliance. High

temperatures may ignite clothing, furniture or draperies.

F. Clear Space

WARNING

RISK OF FIRE! Keep combustible materials, gasoline

and other ammable vapors and liquids clear of

appliance.

• Do NOTstoreammablematerialsintheappliance’s

vicinity.

• Do NOT use gasoline, lantern fuel, kerosene, charcoal

lighteruidorsimilarliquidstostartor“freshenup”a

reinthisheater.

Keep all such liquids well away from the heater while it is

in use as combustible materials may ignite.

WARNING

USE OF IMPROPER FUELS, FIRESTARTERS OR

ALTERING THE STOVE FOR HIGHER HEAT OUTPUT

MAY CAUSE DAMAGE TO THE STOVE AND COULD

RESULT IN A HOUSE FIRE. USE ONLY APPROVED

FUELS AND OPERATION GUIDELINES

WARNING

MOBILE/MANUFACTURED HOME GUIDELINES: DO

NOT ALLOW INSTALLATION IN A SLEEPING ROOM.

WARNING

If you expect that small children or vulnerable adults

may come into contact with this appliance, the following

precautions are recommended:

• Installaphysicalbarriersuchas:

 - Adecorativerescreen.

 - Adjustablesafetygate.

• Never leave children alone near a hot stove, whether

operating or cooling down.

• Teach children to NEVER touch the stove.

• Consider not using the stove when children will be

present.

• Useonlyspeciedcomponentsasreplacementparts.

Othercomponentsmaynotallowyourstovetooperate

as it was intended.

Contact your dealer for more information, or visit: www.

hpba.org/safety-information.

To prevent unintended operation when not using your

stovefor anextendedperiod of time(summermonths,

vacations, trips, etc):

• Unplugstovefromreceptacle.

Due to high temperatures, this stove should be placed

awayfromtrac,furnitureanddraperies.

Children and adults should be alerted to the hazards of

high surface temperatures and should stay away to avoid

burns to the skin and/or clothing.

Youngchildrenshouldbecarefullysupervisedwhenthey

are in the same room as the stove.

Clothing and other ammable materials should not be

placed on or near this stove.

Installation and repair of this stove should be done by

a qualified service person. The appliance should be

inspectedbeforeuseandatleastannuallybyaqualied

serviceperson.Morefrequentcleaningwillberequired.

Itisimperativethatcontrolcompartmentsandcirculating

air passageways of this stove be kept clean.

D. Appliance Safety

WARNING

THIS WOOD HEATER HAS A MANUFACTURER-

SET MINIMUM LOW BURN RATE THAT MUST

NOT BE ALTERED. IT IS AGAINST FEDERAL

REGULATIONS TO ALTER THIS SETTING OR

OTHERWISE OPERATE THIS WOOD HEATER IN

A MANNER INCONSISTENT WITH OPERATING

INSTRUCTIONS IN THIS MANUAL.

Connect the power cord into a 120 VAC, 60 Hz grounded

receptacle. (A surge protector is recommended to protect

the circuit board.) Be sure the polarity of the outlet the stove

is plugged into is correct.

E. California Safety Information

This product and the fuels used to operate this product

(wood), and the products of combustion of such fuels,

can expose you to chemicals including lead and carbon

black, which is known to the State of California to cause

cancer,andcarbonmonoxide,whichisknowtotheStateof

California to cause birth defects or other reproductive harm.

Formoreinformationgoto:www.P65Warnings.ca.gov

WARNING

Harman® • P42i Owner’s Manual • 2023 -___ • 03/2368742-900A

G. Helpful Hints

When operating your Harman®P42i-TCPelletInsert,follow

basic safety standards. Read these instructions carefully

before you attempt to operate the P42i-TC Pellet Insert.

Failure to do so may result in damage to property or personal

injuryandmayvoidtheproductwarranty.

Cleaning Burn Pot: Whenever your stove is not burning, take

the opportunity to scrape the burn pot to remove carbon buildup.

A vacuum cleaner is handy to remove the residue. Be sure the

stove is cold if you use a vacuum.

Carbonbuildupcanbescrapedloosewiththereburningusingthe

specialtoolprovidedwithyourstove.Scrapetheoorandsidesof

the burn pot. The carbon will be pushed out by the incoming fuel.

Always wear gloves when scraping the burnpot.

Disposal of Ashes: Ashes should be placed in a steel

container with a tight tting lid. The closed container of

ashesshouldbeplacedonanon-combustibleoororonthe

ground, well away from all combustible materials, pending

naldisposal.Iftheashesaredisposedofbyburialinsoilor

otherwise locally dispersed, they should be retained in the

closed container until all cinders have thoroughly cooled.

Otherwasteshallnotbeplacedinthiscontainer.

Soot and Flyash Formation and Need for Removal: The

productsofcombustionwillcontainsmallparticlesofyash.

The yash will collect in the exhaust venting system and

restricttheowoftheuegases.Incompletecombustion,

such as occurs during startup, shutdown, or incorrect

operation of the room heater will lead to some soot formation

whichwillcollectintheexhaustventingsystem.Theexhaust

venting system should be inspected at least once every year

to determine if cleaning is necessary.

Whenburningwoodpelletsonlow,thepotentialexistsfor

creosote to form. The venting system should be inspected

periodically throughout the heating season to determine

if creosote buildup has occurred. If a signicant layer of

creosote has accumulated (1/8” or more), it should be

removedtoreducetheriskofachimneyre.Ifareoccurs,

calltheredepartment,shutdownthestove,andevacuate

the residence. Before using the appliance, have the venting

system thoroughly inspected and replace any damaged

components.

With any hearth appliance, installation of smoke detectors/

CarbonMonoxidedetectorsisrecommendedoneverylevel

of the home.

Possible causes of smoke detector activation:

Paintcuringprocess-Openawindowneartheappliance

fortherstfewhoursofburning.

Exhaustbeingdrawnbackinsidethedwelling-Outsideair

connection to the appliance is necessary.

Vent leakage - Follow vent manufacturers instructions for

proper sealing.

CAUTION

This appliance must be vented to the outside.

H. Fuel Specications

TheP42i-TCPelletInsertisapprovedforburninganygrade

ofpelletizedbio-massfuel.

It should be noted, however, that higher ash content will

require more frequent cleaning.

Themoisturecontentofpelletsmustnotexceed8%.Higher

moisturewillrobBTU’sandmaynotburnproperly.

Fuel should not be stored within the stove installation

clearances or within the space required for cleaning and

ash removal.

Fuel and Fuel Storage

Pellet fuel quality can uctuate from manufacturer to

manufacturer, and even from bag to bag.

Hearth&HomeTechnologiesrecommendsusingonlyfuel

thatiscertiedbythePelletFuelsInstitute(PFI).

FuelMaterial

• Madefromsawdustand/orotherwoodby-products

• Sourcematerialtypicallydeterminesashcontent

HigherAshContentMaterial

• Hardwoods with high mineral content

• Bark and leaves as source material

• “Standard”gradepelletsandotherbiomass

LowerAshContentMaterial

• Softwood;pine,r,etc.

• Materialswithlowermineralcontent

• “Premium” grade pellets

Performance

• Higher ash content requires more frequent maintenance.

• “Premium” grade pellets will produce the highest heat

output.

• Burning pellets longer than 1-1/2 inches (38mm) can

cause inconsistent feeding and/or ignition.

Clinkers

• Mineralsandothernon-combustiblematerials,likesand,

willturnintoahardglass-likesubstancewhenheated.

• Trees from dierentareas will vary in mineral content.

For this reason, some fuels will produce more clinkers

than others.

Moisture

• Always burn dry fuel. Burning fuel with high moisture

content takes energy to dry and tends to cool the

appliance thus, robbing heat from your home.

• Damp pellet fuel could turn back into sawdust which

doesnotowproperlythroughthefeedsystem.

Harman® • P42i Owner’s Manual • 2023 -___ • 03/2378742-900A

NOTICE

Hearth&HomeTechnologiesisnotresponsibleforstove

performanceorextramaintenancerequiredasaresultof

using fuel with higher ash or mineral content.

Storage

• Wood pellets should be left in their original sealed bag

until ready to use, to prevent moisture.

• Donotstorefuelwithinthespeciedclearanceareas,or

in a location that will interfere with routine cleaning and

maintenance procedures.

CAUTION

Tested and approved for use with wood pellets ONLY.

Burning of any other fuel will void your warranty.

CAUTION

Do not burn fuel that contains an additive.

• Maycausehopperre

• Damage to product may result

Readthelistofingredientsonthepackaging.

H. Fuel Specications (Cont.)

BURNING COLORED PAPER, CARDBOARD,

SOLVENTS, TRASH AND GARBAGE OR ALTERING

THE STOVE FOR HIGHER HEAT OUTPUT MAY CAUSE

DAMAGE TO THE STOVE AND COULD RESULT IN

A HOUSE FIRE. USE ONLY APPROVED FUELS AND

FOLLOW ONLY THESE OPERATION GUIDELINES.

WARNING

NEVER USE GASOLINE, GASOLINE-TYPE LANTERN

FUEL, KEROSENE, CHARCOAL LIGHTER FLUID, OR

SIMILAR LIQUIDS TO START OR 'FRESHEN UP' A FIRE

IN THIS HEATER. KEEP ALL SUCH LIQUIDS WELL

AWAY FROM THE HEATER, WHILE IN USE.

WARNING

Odorsandvaporsreleasedduringinitialoperation.

• Curing of high temperature paint.

• Openwindowsforaircirculation.

Odorsmaybeirritatingtosensitiveindividuals.

CAUTION

I. EPA Test Settings

AllEPAtestsarerunwiththeunitinConstantBurnMode

andconguredtothesettingsbelow:

Low

Distribution:O

FeedLimit:25%

TemperatureSetting:1.0

Medium

Distribution: 100%

FeedLimit:40%

TemperatureSetting:3.1

High

Distribution: 100%

FeedLimit:95%

TemperatureSetting:7.0

PleaseseetheEASYTouchOwner’sManualprovidedwith

thisunitformoreinformationaboutadjustingsettings.

For additional clarication on EPA testing procedures &

stove settings, please visit https://www.harmanstoves.com/

about-us/epa-certicationtoviewtheEPANon-CBIreport

for this unit.

Harman® • P42i Owner’s Manual • 2023 -___ • 03/2388742-900A

J. Quick Start Guide

2. Fill hopper with pellets

Initial start-up Only

1.SelectLanguage

3.Adjustarrowstosetroomdesiredtemperature.

4.TouchtheOn/OPowerIcon.

Refer to Touch Manual for all other operations.

Please Note: The USB port on the EASY Touch Control is not a charging port for smartphones, tablets etc.

Harman® • P42i Owner’s Manual • 2023 -___ • 03/2398742-900A

ISSUES SOLUTIONS

Metallicnoise. Noise is caused by metal expanding and contracting as it

heats up and cools down, similar to the sound produced

byafurnaceorheatingduct.Thisnoisedoesnotaectthe

operation or longevity of your appliance.

White ash buildup on glass. Thisisnormal.Cleantheglassusinganynon-abrasiveglass

cleaner.

Glass has buildup of black soot Excessive build-up of ash. The lower burn settings will

produce more ash, the higher burn settings produce less.

The more it burns on low the more frequent cleaning of the

glass is required.

Glass has turned dirty. Excessive build up of ash. The lower burn settings will

produce more ash, the higher burn settings produce less.

The more it burns on low the more frequent cleaning of the

glass is required.

Firehastallameswithblacktailsandislazy. The feed rate needs to be reduced or the burnpot needs

cleaning.Heatexchangerorexhaustblowerneedscleaning.

Smokystart-uporpusofsmokefromtheairwash. Burnpot may be dirty, Clean the burnpot.

Largeameatstart-up. This is normal. Flame will settle down once the re is

established.

MissedIgnition Ensure pellets in burnpot

Ensure holes in burnpot are clear of obstructions above the

igniter.SeeBurnpotMaintenance.

Check to see if the ignitor is getting hot, if not replace

ignitor. *See addendum for manual ignition instructions for

emergency heating needs.

K. Frequently Asked Questions

Withproperinstallation,operation, and maintenance your appliance will provide yearsoftrouble-freeservice. If you do

experienceaproblem,thistroubleshootingguidewillassistaqualiedservicepersoninthediagnosisofaproblemandthe

corrective action to be taken.

Contact your dealer for additional information regarding operation and troubleshooting. Visit www.harmanstoves.com

to nd a dealer.

Harman® • P42i Owner’s Manual • 2023 -___ • 03/2310 8742-900A

L. Cleaning Prompts, Messages and Errors

YourEASYTouchControlcommunicateswithyoubyshowingmessagesonthetopcenteroftheEASYTouchControlhome

screen.Ifyouhavemorethanonemessage,themessageswillshowconsecutivelyuntilyouacknowledgethemessageby

performing the task. These communications include:

PROMPTS

MESSAGES

ERRORS

Clean your stove. Call your Harman Dealer if problem

persists.

When prompted, scrape burnpot. Press checkmark to reset.

When prompted, inspect and empty ash pan as needed.

Press checkmark to reset.

When prompted, inspect and perform total clean. Press

checkmark to reset.

Presscheckmarkifyoulledthehopper.Ifyoudidnotll

hopper,Themessagewilldisappearin30seconds.

Replacethe2“AA”batteriesintheWirelessRemoteSensor.

If Wireless Remote Sensor batteries die, the Back Up

Sensorwillcontinuetoheatyourhome.

Check and close the front and ash doors for the stove to

continue to heat.

Close the hopper lid for the stove to continue to heat.

Fill the hopper with pellets. Press checkmark to reset. If

youdid not ll the hopper, the message will stopafter30

seconds.Thiserroronlyappearsif“ShowFuelGauges”is

turned on.

BatteriesinWirelessRemoteSensorhaveexpired.Replace

the 2 “AA” batteries.

ReturnAirSensorhasfailed.CallyourHarmanDealer.

Unit has failed to ignite. Scrape the burnpot. Call your

Harman Dealer if problem persists.

Touch Control has lost communication to the stove. Call

your Harman Dealer.

ExhaustSensingProbe(ESP)asfailed.CleantheESP.If

issue persists, call your Harman Dealer.

Harman® • P42i Owner’s Manual • 2023 -___ • 03/2311 8742-900A

2 2 Maintenance & Service

When properly maintained, your stove will give you many

yearsoftrouble-freeservice.Contact your dealer to answer

questionsregardingproperoperation,trouble-shootingand

service for your appliance. Visit www.harmanstoves.com to

ndadealer.Werecommendannualservicebyaqualied

service technician.

A. Proper Shutdown Procedure

Follow the detailed instructions found in this section

for each step listed in the chart below.

NOTICE

The type of fuel you are burning will dictate how often you

have to clean your burnpot. Clean more frequently if you

encounter heavy build-up of ash at the recommended

interval or you see soot coming from the vent. Not

properly cleaning your appliance on a regular basis

will void your warranty.

Note: Do not use a household vacuum to clean the stove.

We recommend that you use a shop vacuum that is equipped

withanedustltercalledaHEPAlteroravacuumspecially

madeforyashandsoot.USINGAVACUUMWHICHIS

NOTEQUIPPEDWITHAFINEDUSTFILTERWILLBLOW

FLYASHANDSOOTOUTINTOTHEROOM.

NOTE:THESTOVEMUSTBECOMPLETELYOUTBEFORE

YOUVACUUMTHE STOVE.LIVE PELLETEMBERS, IF

SUCKEDINTOTHEVACUUM,WILLLIGHTTHEVACUUM

ONFIREANDMAYULTIMATELYCAUSEAHOUSEFIRE.

Shock and Smoke Hazard

• Turn unit to the off position, let appliance

completelycoolandcombustionfanmustbeo.

Now you can unplug appliance before servicing.

• Smokespillageintoroomcanoccurifappliance

is not cool before unplugging.

• Riskofshockifappliancenotunpluggedbefore

servicing appliance.

CAUTION

Harman® • P42i Owner’s Manual • 2023 -___ • 03/2312 8742-900A

B. Quick Reference Maintenance Chart

Frequency Cleaning Procedure Safety Measures Tips

Daily ScrapeBurnpot Wearameresistantgloves3

Vigorous,strongscrapingspecically

nearneckofburnpot.Scrapeevery

time you add pellets or at least every

3bagsoffuel.2

Weekly

Empty Ash Pan

Wear protective gloves.1

Putashesintoasteelnon-

combustible container with tight

ttinglidoutside.

Unitdoesnotneedtobeturnedo.

Reducetolowburnduringremoval.

Clean the Glass Stovemustbeturnedoandcold.

Monthly

Scrape&VacuumHeatExchanger Stovemustbeturnedoandcold. Useprovidedscraper.Scrapeback

andsidesofrebox.

Brush&vacuumthedistributionfan Stovemustbeturnedo,coldand

unplugged from power supply.

Useprovidedpaintbrush.This

shouldbedoneapproximatelyevery

25bags.2

InspectHopperlidgasketfor

damage

Replacegasketingiffrays,tearsor

other visible damage to gasket. This

shouldbedoneapproximatelyevery

50bags.2

CleanIgniter

Stovemustbeturnedo,coldand

unplugged from power supply.

Wear protective gloves.1

Putashesintoasteelnon-

combustible container with tight

ttinglidoutside.

Useprovidedpaintbrush.Vacuum

loose ash from around igniter and

inside burn pot.

Stove MUST be turned o, cold and unplugged from power supply for Yearly Cleaning.

Yearly4

Brush&vacuumthecombustionfan

andventing/exhaustpath

Wear protective gloves.1

Putashesintoasteelnon-

combustible container with tight

ttinglidoutside.

Useprovidedpaintbrushtobrush

fanblades.*Useuebrushtoclean

venting being careful not to damage

theESP.2

Inspectdoorgasket Replacegasketingiffrays,tearsor

other visible damage to gasket.

Brush&vacuumventingsystem

Wear protective gloves.1

Putashesintoasteelnon-

combustible container with tight

ttinglidoutside.

*Auebrushofappropriatesizeandlengthmayneedtobepurchasedforpropermaintenance.

1. Protective gloves will help prevent skin abrasion while working on steel surfaces.

2.Frequencyofcleaningdependslargelyonfueltype.Lowerqualitypelletsrequiremostfrequentcleaning.

3.Flameresistantgloveswillhelpprotectyourskinfrompotentialcontactwithheatorames.

4. Yearly cleaning is also known as a Total Clean.This requires completing all the Daily, Weekly, Monthly and Yearly

maintenance mentioned. This should be done before you begin burning the unit each heating season.

Harman® • P42i Owner’s Manual • 2023 -___ • 03/2313 8742-900A

C. Unit Maintenance

Daily/Weekly Maintenance:Itisrecommendthattheburn

potbescrapedwheneveraddingfuel;takingtheopportunity

to clean the burn pot will ensure proper daily operation.

Scraping the Burn Pot-

• Usingameresistantgloves,vigorouslyscrapethetop

holed surface and sides of the burn pot down to auger

tube, be sure to concentrate in the neck of the burnpot.

Figure 2.1.

• Scrapeloosenedmaterialoveredgeofburnpotgrateinto

the ashpan.

• Ifneeded,emptytheashpanwhileaddingfuelandafter

scraping the burn pot.

Monthly Maintenance: It is recommend that the unit

be shut down and unplugged from any power source for

a monthly cleaning. Monthly cleanings will ensure proper

operation of your unit throughout the heating season.

• CleaningGlass-Onceunitiscold,useanon-abrasive

glass cleaner on glass and wipe clean.

• ScrapeandVacuumHeatExchanger.

Cleaning the Heat Exchanger-

Removing the Center Medallion:

1. Liftuponthe2bottomcornersofthemedallionuntilitis

higherthanthetopoftheameguide.

2. Pullthebottomedgeofthemedallionfrontapproximately

1 inch.

3. Pulldownwardonthecornersofthemedallionuntilthe

top is released from the retainer that keeps the top aligned

when in place. Figure 2.2.

Figure 2.2

1st - UP ↑

2nd - OUT

3rd - DOWN ↓

Figure 2.3

ScrapetheheatexchangerfreeofFly-Ashandcarbonbuild-up

Cleaning the Heat Exchanger:

Usingthescraperprovidedrunthestraightedgealongthe

at surface of the Heat Exchanger removing any carbon

depositsorashbuild-up.Figure2.3.

Figure 2.1

Harman® • P42i Owner’s Manual • 2023 -___ • 03/2314 8742-900A

AftertheHeatExchangerhasbeenscraped,usethedust

brushsuppliedtoremoveanyremainingy-ashfromtheHeat

Exchanger as well as other areas throughout the rebox.

Figure2.5.

Figure 2.5

BrushthereboxfreeofremainingFly-Ash.

Figure 2.6

Cleaning the Burn Pot-

• Vigorously scrape the top holed surface and sides of the

burn pot down to auger tube, as suggested in the Daily/

WeeklyMaintenanceSection.

• Usethesuppliedallenwrenchtoremoveanybuild-upthat

may have accumulated in the holes of the burn pot grate.

Simply push the allen wrench down through each hole

ensuringitisclearofanybuild-uppayingattentionnotto

damage the igniter element in the process. Figure 2.6.

Disconnect the power to the unit before removing

cover.

DANGER

• Loosenthe(2)wingthumbscrewsonthelowerfrontangle

of the burn pot. Figure 2.7

• Liftotheclean-outcovertoopenthebottomclean-out

chamber. Figure 2.8

• Clean ash buildup from inside the chamber while cover

iso.Usethescrapertotaponthetopfrontedgeofthe

burn pot. This will help knock pieces of ash, loosened by

thescrapingprocess,downthroughtheholes.Italsohelps

knock ash buildup from the igniter element and bracket.

Clean Ash Accumulation

Figure 2.8

Figure 2.7

WingThumbScrews

Harman® • P42i Owner’s Manual • 2023 -___ • 03/2315 8742-900A

Cleaning Igniter Bracket-

Check cleanliness of the igniter and inner burnpot. If the

igniter has ash buildup it must be removed to ensure proper

ignition.Usetheprovidedbrushtoremoveashbuildupfrom

inandaroundtheigniter.Onceashisloose,vacuumaround

igniter and at the base of burn pot. Figure 2.9.

Note: The hot lead/cold lead connection must always

be pulled to the rear of the feeder body before

operation.

Use caution when cleaning burn pot clean-out

chamber. Do not damage the high temperature igniter

wires.

WARNING

Clean Ash Accumulation

Figure 2.9

Yearly Maintenance: Cleaning the Combustion Fan

Chamber-

RemovethecombustioncoverassemblyFigure2.11.Todo

this, pull up on the combustion cover latch Figure 2.12, and

pull the combustion cover assembly toward you and out.

NOTE: Whenre-installingtheCombustionCoverAssembly

makesureyouinsertthebottomofthecoverrstandthen

slide to the left to engage the bolt, prior to putting it into place.

Figure 2.11

LowerCombustionChamber

Combustion Cover Assembly

Figure 2.12

CombustionCoverLatch

Once combustion cover assembly is removed you now

have access to clean the combustion blower chamber area.

Figure2.13.

UpperCombustionChamber

Figure 2.13

Harman® • P42i Owner’s Manual • 2023 -___ • 03/2316 8742-900A

Caring for your Glass-

The glass used in your stove is manufactured to exact

standardstowithstandthehighheatofthere,butlikeall

glass, it must be treated with common sense and care. Never

abuse the glass by slamming the door shut or striking the

glasswithaheavyobject.Iftheglassisbrokenordamaged,

do not operate the stove until it has been replaced.

Glass - Replacement:

Ifthestove’sglassiscrackedorbroken,youmustreplace

it before operating your stove. Remove pieces carefully.

Replace glass only with Harman® replacement glass; do

not use substitutes.

Carefully remove damaged glass, gasket material, and glass

clips (set aside).

Installtheselfadhesive1/4”gasketmaterialaroundthefront

faceoftheglass.Settheglasspanelandgasketgentlyonto

thedoor. Install the glass clips and 1/4-20 X 1/2”screws.

Note:1/4-20X1/2”screwsonlyneedtobesnugt.Donot

overtighten.

Glass - Cleaning:

Sometimesitwillbe necessarytoclean accumulatedash

fromtheglasssurface;allowingthisashtoremainonthe

glass for long periods can result in “etching” due to the acidity

of the ash. Never clean the glass while it is hot, and do not

use abrasive substances. Wash the surface with cool water

andrinsethoroughly.Youmaywishtouseanon-abrasive

cleanerspecicallydesignedforuseonstoveglass.Inany

case, dry thoroughly before relighting your stove.

Glass Gasket

Replace glass only with high

temperature ceramic glass.

Inspect door gasket during

cleaning and inspection

(4) Glass Clips

(4)1/4-20X1/2”

ButtonHeadScrew

Figure 2.14

Figure 2.15

Inspect hopper lid gasket

during cleaning and inspection

Inspect all Gaskets-

While the unit is cool, inspect all door gaskets to ensure

proper seal. The gasket should be continuous without frays

ortears;havingplyablegasketmeanshavingacorrectseal

forproperoperation.Figures2.14&2.15.

Distribution Blower-

Checking the distribution blowers yearly is a good habit to

get into. Dust, animal hair or anything else that can make

its way into that area can drastically cut down on the air

movement throughout the unit ultimately causing less of a

heatingeciency.

Oncetheunitisshutdownandcooled,unplugtheunitfrom

its power supply. Behind each side panel release (1) spring

latches that holds the unit to the inserts cage. Figure 2.16.

Figure 2.16

Openspringlatch

Harman® • P42i Owner’s Manual • 2023 -___ • 03/2317 8742-900A

Once unit is pulled away from the replace, thoroughly

vacuum around the Distribution Blowers. Figure 2.17.

Figure 2.17

Distribution Blower

Cleaning Venting System-

It is recommend that a certied chimney sweep perform

service and inspection to your chimney system to ensure

your unit is vented safely and in accordance to local code.

Harman® • P42i Owner’s Manual • 2023 -___ • 03/2318 8742-900A

A. Service Parts List

3 3 Reference Material

Service Parts P42i-TC

Beginning Manufacturing Date: May 2023

Ending Manufacturing Date: Active

Part number list on following page.

Pellet Insert

1-90-742200-1 - 20” Hopper

03/23

1-90-742240-1 - 24” Hopper

Harman® • P42i Owner’s Manual • 2023 -___ • 03/2319 8742-900A

Service Parts P42i-TC

Beginning Manufacturing Date: May 2023

Ending Manufacturing Date: Active

IMPORTANT: THIS IS DATED INFORMATION. Parts must be ordered from a dealer or distributor.

Hearth and Home Technologies does not sell directly to consumers. Provide model number

and serial number when requesting service parts from your dealer or distributor.

Stocked

at Depot

ITEM Description COMMENTS PART NUMBER

1Mounting Frame Assembly 1-10-584031A

Roller hardware 4 sets 1-00-02243 Y

2 All Thread .500-13 x 12, Frame Jacking Qty 2 req 3-31-00949

Jack Plate Qty 2 req 1-10-574099W

3 Pipe Stub for 4 in. Flex/PL w/gasket 1-00-574034 Y

4 Pipe Stub Plate Gasket 3-44-574045 Y

5 Docking Gasket Silicone 3-44-06108 Y

6 Thermister Probe (ESP Probe) 3-20-00844 Y

7Gasket, Hopper Top 20 ft 1-00-375501 Y

Gasket, Hopper Throat 3-44-677185 Y

8 Control Board 1-00-05372 Y

9 Control Board Mounting Plate 1-10-584012A

10 Dierential Switch 3-20-6866 Y

Silicone Tubing, 1/8” 5 Ft 1-00-5113574 Y

11 Hinge Set (4 pc), Side Panel 2 Sets SRV8742-7890

12 Surround, Standard 1-00-742667-1

Surround Hardware Pack SRV8000-042

13 Side Panel Left SRV8742-103L

14 Line Filter Mounting Bracket 1-00-584034

Line Filter 3-20-803744 Y

15 Combustion Cover Latch Assembly 1-00-574080

16 Medallion Holder 1-10-574098W Y

17 Cast Center Medallion 3-00-584027 Y

18 Burn Pot Weldment See following page

19 Ash Pan 1-10-574007A Y

20 Cast Top / Hopper Lid Assembly See following page

21 Door Assembly See following page

22 Cast Bottom Ashlip SRV8742-018

Door Magnet and Hardware (1 set) Qty 4 req SRV8787-020

23 Combustion Cover 1-10-574087A

24 Hinge Plate Qty 2 req 3-00-674047

25 Side Panel Right SRV8742-103R

26 Spring Latches with hardware Set of 2 1-00-00927 Y

27 Fan Blade Commonly required

for Combustion Blower

replacement

1-10-574500A Y

Blower Mounting Screws (5 Sets) 1-00-832150

28 Combustion Blower 1-00-02275 Y

Additional service parts on following page.

Harman® • P42i Owner’s Manual • 2023 -___ • 03/2320 8742-900A

Service Parts P42i-TC

Beginning Manufacturing Date: May 2023

Ending Manufacturing Date: Active

IMPORTANT: THIS IS DATED INFORMATION. Parts must be ordered from a dealer or

distributor. Hearth and Home Technologies does not sell directly to consumers. Provide

model number and serial number when requesting service parts from your dealer or distributor.

Stocked

at Depot

ITEM Description COMMENTS PART NUMBER

29 Feeder Assembly See following page

30 Distribution Blower 3-21-33647 Y

18.1 Burn Pot Weldment w/Cradle 1-00-574605 Y

18.2 Igniter Element 3-20-677200 Y

Pkg of 10 1-00-677200 Y

18.3 Igniter Cradle 1-00-777907 Y

18.4 Burn Pot Cleanout Cover w/Wing Screws 2 sets 1-00-06623 Y

18.5 Thumb Screw, 1/4-20 x 5/8 Pkg of 10 3-31-782108-10 Y

Gasket, Burn Pot 3-44-237639 Y

Flame Guide 3-00-03000 Y

Additional service parts on following page.

18.1

18.2

18.3

18.4

18.5

#18 Burn Pot Weldment

La page charge ...

Harman P42i-TC Pellet Insert Le manuel du propriétaire

Marque: Harman

Modèle: P42i-TC Pellet Insert

Catégorie: Cheminées

Taper: Le manuel du propriétaire

Télécharger le PDF

rapport

dans d''autres langues

English: Harman P42i-TC Pellet Insert Owner's manual

Harman P42i-TC Pellet Insert Le manuel du propriétaire

Harman P42i-TC Pellet Insert Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents