Quadrafire Santa Fe Pellet Stove Manuel utilisateur

Catégorie
Poêles
Taper
Manuel utilisateur
1 September 26, 20197050-802C
NOTICE: DO NOT DISCARD THIS MANUAL
R
SANTA FE PELLET APPLIANCE
MODEL(S):
SANTAFE-C
Owners Manual
Operation & Care
INSTALLER: Leave this manual with party responsible for use and operation.
OWNER: Retain this manual for future reference.
Contact your dealer with questions on installation, operation, or service.
Installation and service of this appliance should be performed by
qualified personnel. Hearth & Home Technologies recommends
HHT Factory Trained or NFI certified professionals.
Tested and approved for wood pellets only. Burning of
any other type of fuel voids your warranty.
CAUTION
CAUTION
Check building codes prior to installation.
Installation MUST comply with local, regional, state
and national codes and regulations.
Consult local building, re ocials or authorities
having jurisdiction about restrictions, installation
inspection, and permits.
WARNING
If the information in these instructions is
not followed exactly, a re could result
causing property damage, personal injury,
or death.
Do not store or use gasoline or other ammable
vapors and liquids in the vicinity of this or any
other appliance.
Do not over re - If appliance or chimney connector
glows, you are over ring. Over ring will void
your warranty.
Comply with all minimum clearances to combustibles
as specied. Failure to comply may cause house re.
HOT SURFACES!
Glass and other surfaces are hot
during operation AND cool down. Hot
glass will cause burns.
WARNING
Do not touch glass until it is cooled
NEVER allow children to touch glass
Keep children away
CAREFULLY SUPERVISE children in same room
as replace.
Alert children and adults to hazards of
high temperatures
High temperatures may ignite clothing or other
ammable materials.
Keep clothing, furniture, draperies and other
ammable materials away.
NOTE: To obtain a French translation of this
manual, please contact your dealer or visit
www.quadrare.com
REMARQUE : Pour obtenir une traduction française de
ce manuel, s’il vous plaît contacter votre
revendeur ou visitez www.quadrare.com
2 September 26, 20197050-802C
SANTA FE FREESTANDING
A. Sample of Serial Number / Safety Label
LOCATION: Back of Appliance
Serial No.
Mfg. Date
Test Lab &
Report No.
Model
Name
and Welcome to the Quadra-Fire Family!
NOTE: Clearances may only be reduced by means approved by the regulatory
authority having jurisdiction.
HOT WHILE IN OPERATION DO NOT TOUCH. KEEP CHILDREN, CLOTHING
AND FURNITURE AWAY. CONTACT MAY CAUSE SKIN BURNS. SEE
CAUTION:
Listed Solid Fuel Room Heater/Pellet Type. Also suitable for Mobile Home Installation. This appliance has been tested and listed for use in Manufactured Homes in accordance with OAR
814-23-9000 through 814-23-909.
/ Appareil de chauffage de combustible solide/de type de boulettes. Accepté dans l'installation dans les maisons mobiles. Cet appareil a été testé et enregistré pour
l'usage dans les Maisons Mobiles en accord avec OAR 814-23-9000 jusqu'à 814-23-909.
PREVENT HOUSE FIRES /
PRÉVENTION DES FEUX DE MAISON
Install and use only in accordance with manufacturer's installation and operating instructions. CONTACT LOCAL BUILDING OR FIRE OFFICIALS ABOUT RESTRICTIONS AND INSPECTION IN YOUR AREA.
WARNING - FOR MOBILE HOMES: Do not install appliance in a sleeping room. An outside combustion air inlet must be provided. The structural integrity of the mobile home floor, ceiling and walls must be
maintained. Refer to manufacturer's instructions and local codes for precautions required for passing chimney through a combustible wall or ceiling. INSPECT AND CLEAN VENT SYSTEM FREQUENTLY IN
ACCORDANCE WITH MANUFACTURER'S INSTRUCTIONS. DO NOT CONNECT THIS UNIT TO A CHIMNEY SERVING ANOTHER APPLIANCE. Use a 3" or 4" diameter type "L" or "PL" venting system.
Installez et utilisez en accord avec les instructions d'installation et d'opération du fabricant. CONTACTEZ LE BUREAU DE LA CONSTRUCTION OU LE BUREAU DES INCENDIES AU SUJET
DES RESTRICTIONS ET DES INSPECTIONS D'INSTALLATION DANS VOTRE VOISINAGE. Ne pas obstruez l'espace en dessous de l'appareil. AVIS - Pour Les Maisons Mobiles: Ne pas
installer dans une chambre à coucher. Un tuyau extérieur de combustion d'air doit être installé et ne doit pas être obstrué lorsque l'appareil est en usage. La structure intégrale du plancher, du
plafond et des murs de la maison mobile doit être maintenue intacte. Référez vous aux instructions du fabricant et des codes locaux pour les précautions requises pour passer une cheminée à
travers un mur ou un plafond combustibles, et les compensations maximums. INSPECTEZ ET NETTOYEZ LA CHEMINÉE FRÉQUEMMENT. Ne pas connecter cet appareil à une
cheminée servant un autre appareil. Utilisez systèm de ventilation "L" ou "P" diamètre 76mm ou 102mm
Tested to: ASTM E1509-04, ULC-S627-00, ORD-C1482-M1990 Room Heating Pellet BurningType, (UM) 84-HUD FOR USE ONLY WITH PELLETIZED WOOD OR SHELLED FIELD
CORN FUEL. DO NOT USE ANY OTHER TYPE OF FUEL. OMNI-Test Laboratories, Inc. has determined that this appliance complies with Canadian Standards Association (CSA)
B415.1 and Title 40 of the U.S. Code of Federal Regulations, Part 60, SubPart AAA.OMNI-Test Laboratories Accrediations: The Standards Council of Canada, the American National
Standards Institute, and the U.S. Environmental Protection Agency. Input Rating: 30,600 Btu's/hr. Electrical Rating:115 VAC, 60 Hz, Start 4.1 Amps, Run 1.1 AMPS. Route power cord
away from unit. Do not route cord under or in front of appliance. Do not obstruct the space beneath the heater. DANGER: Risk of electrical shock. Disconnect power supply before
servicing. Replace glass only with 5mm ceramic available from your dealer. To start, set thermostat above room temperature, the stove will light automatically. To shutdown, set
thermostat to below room temperature. For further instruction refer to owner's manual. KEEP VIEWING AND ASH REMOVAL DOORS TIGHTLY CLOSED DURING OPERATION.
CAUTION: COMBUSTION AIR OPENINGS ARE NOT TO BE OBSTRUCTED.
Testé à: ASTM E1509-04, ULC-S627-00, ORD-C1482-M1990 Room Heating. Pellet Burning Type, (UM) 84-HUD POUR USAGE AVEC LES BOULETTES DE BOIS OU DE COMBUSTIBLE DE MAIS ÉCOSSÉ DES
CHAMPS. N’utiliser aucun autre genre de combustible. OMNI-Test Laboratories, Inc. a déterminé que cet appareil se conforme avec la norme de l’Association Canadienne de normalisation (CSA) B415.1 ainsi que
le Titre 40 du Code Fédéral de Régulations des États-Unis, partie 60, sous-partie AAA. Accréditations OMNI-Test Laboratories : Le Conseil Canadien des Normes (CCN/SCC), l’Institue des Standards Nationaux
Américain (ANSI) et l’Agence de Protection Environnemental (EPA). Puissance de Rendement : 30 600 Btu's/hr. Puissance Électrique: 115 VAC, 60 Hz, Début 4.1 Amps, Courir 1.1 Amps, Éloignez le fil électrique
de l'appareil. Ne pas faire passer le fil électrique au dessus ou en dessous de l'appareil. Ne pas bloquer l’espace au dessous de l’appareil. DANGER: Il y a risque de décharge électrique. Déconnectez le fil
électrique de la prise de contact avant le service. Remplacez la vitre seulement avec une vitre céramique de 5 mm disponible chez votre fournisseur. Pour allumer, monter la température du thermostat au dessus de
la température de la pièce, le poêle s'allumera automatiquement. Pour éteindre, descendre la température du thermostat en dessous de la température de la pièce. Pour des instructions supplémentaires, référez
vous au manuel du propriétaire. GARDEZ LA PORTE D'OUVERTURE ET LA PORTE DES CENDRES FERMÉES HERMÉTIQUEMENT DURANT L'OPÉRATION. ATTENTION:
OUVERTURES DE COMBUSTION AIR NE SONT PAS À ÊTRE OBSTRUÉE.
MINIMUM CLEARANCES TO COMBUSTIBLE MATERIALS /
ESPACES LIBRES MINIMUM DES MATÉRIAUX COMBUSTIBLES:
Made in China /
Fait Aux Chine
352 Mountain House Road
Halifax, PA 17032
Manufactured by:Fabriqué par:
C
C
A
B
A Back Wall / Mur Arrière 2"/51mm
B Side Wall / Mur De Côté 6"/152mm
CORNER INSTALLATION / INSTALLATION DU COIN :
C Side Wall / Mur De Côté 2"/51mm
VERTICAL 3" - 3" ADAPTER KIT (PART 811-0860) INSTALLATION:
UN ASSEMBLAGE POUR ADAPTEUR 3" - 3" (PIÈCE 811-0860) POUR INSTALLATION VERTICALE :
D Pipe to Back Wall / Un Tuyau Mur Arrière 3"/76mm
E Side Wall / Mur De Côté 6"/152mm
F Back Wall / Mur Arrière 7"/178mm
CORNER INSTALLATION WITH VERTICAL ADAPTER KIT:
INSTALLATION DU COIN AVEC UN ASSEMBLAGE D'ADAPTEUR VERTICAL :
G Side Wall / Mur De Côté 2"/51mm
H Pipe to Side Wall / Un Tuyau Mur De Côté 3"/76mm
ALCOVE INSTALLATION / INSTALLATION DE L' ALCÔVE:
Min. Alcove Height: / Une hauteur minimum de l'alcôve 43"/1092mm
Min. Alcove Side Wall: / Une hauteur minimum mur de côté de l'alcôve 6"/152mm
Min. Alcove Width / Une épaisseur minimum mur de côté de l'alcôve 38"/965mm
Max. Alcove Depth: / La profondeur maximum de l'alcôve 36"/914mm
NOTE 1:
In residential installations, when using Parts 811-0860, (3" - 3" Top Vent Adapter) and 812-3570 (3" - 6" Offset Adapter), 24 gauge 6" single wall flue connector may be used.
NOTE 1 : Dans les installations résidentielles, lorsque les pièces 811-0860, (dessus de l'adapteur de ventilation 3" - 3") et 812-3570 (le ressaut de l'adapteur 3" - 6"), un tuyau
connecteur de 6" pour mur simple de calibre 24 peut être utilisé.
NOTE 2: In manufactured home installation, when using Part 811-0860, (3" - 3" Top Vent Adapter) and 812-3570 (3' - 6" Offset Adapter), use listed double wall flue connector. An
Outside Air Kit (Part 811-0872), must be used with manufactured home installation.
NOTE 2 : Pour l'installation dans les maisons préfabriquées, lorsque les pièces 811-0860, (dessus de l'adapteur de ventilation 3" - 3") et 812-3570 (le ressaut de l'adapteur 3" - 6"),
utilisez un tuyau connecteur enregistré pour mur double. Un assemblage d'air extérieur (pièce 811-0872), doit être utilisé pour l'installation dans les maisons préfabriquées.
D
E
F
www.quadrafire.com
G
G
H
H
The non-combustible floor protector must be 1/2" (13mm) minimum thickness, "k" value = 0.49, Type II thermal protection R = 1.0
or greater.
G 2 in. (203MM)
H* 2 in. (51MM)
I 6 in. (457mm)
FLOOR PROTECTION / PROTECTION DU SOL
*
Non-combustible floor protection must extend 2 inches (51mm) beneath the flue pipe when installed with horizontal venting or
under the Top Vent Adapter with vertical installation. RECOMMENDED IN USA; REQUIRED IN CANADA.
Le protecteur de plancher doit être d'un minimum de 1/2" (13mm) d'épaisseur,'k" value = 0.49, Type II thermique R = 1.0 au
une plus grande de matériel incombustible ou équivalent.
*Un protecteur incombustible de plancher doit s'étendre 2 inches (51mm) sous le conduit de cheminée pour une installation
de ventilation horizontale ou sous un adapteur de ventilation de dessus pour une installation verticale.
ÉTATS-UNIS-RECOMMANDÉ; CANADA - REQUIRENT.
G
I
*H
G
USA
G
I
*H
G
CANADA
7050-800B
CHAUD LORS DE L'OPÉRATION. NE PAS TOUCHER. GARDEZ LES ENFANTS ET LES
VÊTEMENTS LOIN DE L'ESPACE DÉSIGNÉ DE L'INSTALLATION. LE CONTACT PEUT
ATTENTION:
NAMEPLATE AND INSTRUCTIONS. Operate this unit with fuel hopper lid closed. Failure to do
so may result in emissions products' combustion from the hopper under certain conditions.
Maintain hopper seal in good condition. Do not over fill the hopper.
Report / Rapport
061-S-77d-6.2
0061PM077E
Serial No. / N° de série
US
BARCODE LABEL
SANTA FE-C
PELLET STOVE
R
DO NOT REMOVE THIS LABEL / NE PAS ENLEVER L'ÉTIQUETTE
2019
2020
2021 JAN FEB MAR APR MAY JUN
JUL AUG SEP OCT NOV DEC
CAUSER DES BRÛLURES À LA PEAU. VOIR L'ÉTIQUETTE ET LES INSTRUCTIONS. Opérez cet appareil avec le couvercle de la trémie fermé. Le
défaut de ne pas suivre les instructions peut résulter, sous certaines conditions, en une combustion des émissions des produits venant de la
trémie. Ne pas remplir la trémie trop pleine.
U.S. ENVIRONMENTAL PROTECTION AGENCY
Certified to comply with 2020 particulate emission standards at 1.1 g/hr EPA method 28R and ASTM 2779 using premium wood pellets.
This wood heater needs periodic inspection and repair for proper operation. Consult the owner’s manual for further information. It is against federal
regulations to operate this wood heater in a manner inconsistent with the operating instructions in the owner’s manual.
SAMPLE
3September 26, 2019 7050-802C
SANTA FE FREESTANDING
Quadra-Fire is a registered trademark of Hearth & Home Technologies.
A. Sample of Serial Number / Safety Label ......... 2
B. Warranty Policy ............................ 4
1 Listing and Code Approvals ..............7
A. Appliance Certication....................... 7
B. BTU & Eciency Specications ............... 7
C. Glass Specications ........................ 8
D. Electrical Rating ........................... 8
E. Mobile Home Approved ...................... 8
F. Sleeping Room ............................ 8
G. California - Prop65 ......................... 8
2 Operating Instructions .......................9
A. Fire Safety ................................ 9
B. Non-Combustible Materials ................... 9
C. Combustible Materials....................... 9
D. Fuel Material and Fuel Storage................ 9
E. Before Your First Fire ...................... 10
F. Filling the Hopper.......................... 10
G. General Operating Information ............... 11
H. Starting Your First Fire ..................... 11
I. Fire Characteristics......................... 12
J. Feed Rate Adjustment Instructions ............ 12
K. Ignition Cycles ............................ 13
L. Restarting the Appliance .................... 13
M. Clear Space ............................. 13
N. Thermostat Controls ....................... 14
O. Thermostat Setup Options .................. 14
P. Thermostat Operation Instructions............. 15
Q. Thermostat Temperature Programs ........... 15
R. Thermostat Other Features.................. 16
S. Thermostat Battery Replacement ............. 17
T. Frequently Asked Questions ................. 18
3 Maintenance and Service .................19
A. Proper Shutdown Procedure ................. 19
B. Quick Reference Maintenance Chart .......... 19
C. General Maintenance and Cleaning ........... 20
D. Soot or Creosote Fire Awareness ............. 23
E. High Ash Fuel Content Maintenance........... 23
4 Troubleshooting Guide .....................24
5 Service Parts Replacement ..............26
A. Blower Replacement ....................... 26
B. Snap Disc #2 Replacement.................. 27
C. Bae Replacement........................ 28
D. Brick Replacement ........................ 28
E. Igniter Replacement ....................... 29
F. Glass Replacement ........................ 29
6 Reference Materials ..........................30
A. Component Functions ..................... 30
B. Component Locations ...................... 32
C. Service & Maintenance Log ................. 33
D. Exploded Drawings ........................ 34
E. Service Parts ............................. 35
F. Accessories .............................. 38
TABLE OF CONTENTS
Safety Alert Key:
DANGER! Indicates a hazardous situation which, if not avoided will result in death or serious injury.
WARNING! Indicates a hazardous situation which, if not avoided could result in death or serious injury.
CAUTION! Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.
NOTICE: Indicates practices which may cause damage to the appliance or to property.
4 September 26, 20197050-802C
SANTA FE FREESTANDING
B. Warranty Policy
4021-645J • 08-03-171
Hearth & Home Technologies
LIMITED LIFETIME WARRANTY
Hearth & Home Technologies, on behalf of its hearth brands (“HHT”), extends the following warranty for HHT gas, wood, pellet and
electric hearth appliances that are purchased from an HHT authorized dealer.
WARRANTY COVERAGE:
WARRANTY PERIOD:
distributor, whichever occurs earlier. However, the warranty shall commence no later than 24 months following the date of product
is produced in the following table.
Parts Labor Gas Pellet Wood Electric Venting Components Covered
X X
Igniters, auger motors, electronic components, and
glass
X X X
Factory-installed blowers
X
Molded refractory panels
X
Ignition Modules
X
Firepots, burnpots, mechanical feeders/auger
assemblies
X
Vent Free burners, Vent Free ceramic fiber logs,
Aluminized Burners
X X
Castings and Baffles
6 years 3 years
X
Catalyst - limitations listed
7 years 3 years
X X
Manifold tubes, HHT chimney and termination
10 years 1 year
X
Burners, logs and refractory
Limited
Lifetime
3 years
X X X
Firebox and heat exchanger, Grate and Stainless
Steel Burners, FlexBurn® System (engine, inner
cover,access cover and fireback)
X X X X X
All replacement parts beyond warranty period
Warranty Period HHT Manufactured Appliances and Venting
All parts and material except as covered by
Conditions, Exclusions, and Limitations listed
X X X
2 years
3 years
1 Year
90 Days
5 years 1 year
xX
5September 26, 2019 7050-802C
SANTA FE FREESTANDING
4021-645J • 08-03-172
WARRANTY CONDITIONS:
This warranty only covers HHT appliances that are purchased through an HHT authorized dealer or distributor. A list of HHT
authorized dealers is available on the HHT branded websites.
This warranty is only valid in the country in which the HHT authorized dealer or distributor that sold the appliance resides.
Contact your installing dealer for warranty service. If the installing dealer or distributor is unable to provide necessary parts, contact
other than the dealer from whom you originally purchased the product.
Check with your dealer in advance for any costs to you when arranging a warranty call. Travel and shipping charges for parts are not
covered by this warranty.
Limited Catalyst Warranty
o For wood burning products containing a catalyst, the catalyst will be warranted for a six-year period as follows: if the original
o From 37 to 72 months a pro-rated credit will be allowed against a replacement catalyst and labor credit necessary to install
Amount of Time Since Purchase Credit Towards Replacement Cost
0 - 36 Months 100%
37 - 48 Months 30%
49 - 60 Months 20%
61 - 72 Months 10%
o Any replacement catalyst will be warranted under the terms of the catalyst warranty for the remaining term of the original
WARRANTY EXCLUSIONS:
This warranty does not cover the following:
Repair or replacement of parts that are subject to normal wear and tear during the warranty period are not covered. These parts
this noise are not covered by this warranty.
6 September 26, 20197050-802C
SANTA FE FREESTANDING
4021-645J • 08-03-173
This warranty is void if:
There is any damage to the appliance or other components due to water or weather damage which is the result of, but not limited
LIMITATIONS OF LIABILITY
have other rights, which vary from state to state. EXCEPT TO THE EXTENT PROVIDED BY LAW, HHT MAKES NO EXPRESS WARRANTIES
OTHER THAN THE WARRANTY SPECIFIED HEREIN. THE DURATION OF ANY IMPLIED WARRANTY IS LIMITED TO DURATION OF THE
EXPRESSED WARRANTY SPECIFIED ABOVE.
7September 26, 2019 7050-802C
SANTA FE FREESTANDING
Model Santa Fe Pellet Appliance
Laboratory OMNI Test Laboratories, Inc.
Safety
Report No.
061-S-77d-6.2
Type
Solid Fuel Room Appliance/Pellet Fuel
Burning Type
Standard
ASTM E1509-04, ULC S627-00 and ULC/
ORD-C1482-M1990 Room Appliance
Pellet Fuel Burning type and (UM) 84-
HUD, Mobile Home Approved.
This pellet appliance needs periodic inspection and repair for proper operation. It is against federal regulations to operate
this pellet appliance in a manner inconsistent with operating instructions in this manual.
1 Listing and Code Approvals
A. Appliance Certication
NOTICE: This installation must conform with local codes. In the absence of local codes you must comply with the ASTM
E1509-04, ULC S627-00, (UM) 84-HUD and ULC/ORD-C-1482.
B. BTU & Eciency Specications
Emissions Report
Number:
0061PM077E
EPA Certication
Number:
175-19
EPA Certied Emissions: 1.1 grams per hour
*LHV Tested Eciency: 70.4%
**HHV Tested Eciency: 66.1%
***EPA BTU Output: 5,800 to 22,400 / hr.
****BTU Input: 9,300 to 30,600 / hr.
Vent Size:
3 or 4 “L” or “PL”, or 6
inches
Hopper Capacity: 52 lbs.
Fuel Premium Wood Pellets
* Weighted average LHV eciency using data collected
during EPA emissions test.
**Weighted average HHV eciency using data collected
during EPA emissions test.
***A range of BTU outputs based on HHV and the burn
rates from the low and high EPA tests.
****Maximum BTU input based on the high burn section
of the EPA emissions test.
The Santa Fe is Certied to comply with
2020 particulate emission standards.
8 September 26, 20197050-802C
SANTA FE FREESTANDING
Improper installation, adjustment, alteration, service or
maintenance can cause injury or property damage.
For assistance or additional information, consult a qualied
installer, service agency or your dealer.
C. Glass Specications
This appliance is equipped with 5mm ceramic glass.
Replace glass only with 5mm ceramic glass. Please
contact your dealer for replacement glass.
D. Electrical Rating
115 VAC, 60 Hz, Start 4.1 Amps, Run 1.1 Amps
E. Mobile Home Approved
This appliance is approved for mobile home
installations when not installed in a sleeping room and
when an outside combustion air inlet is provided.
The structural integrity of the mobile home oor, ceiling,
and walls must be maintained.
The appliance must be properly grounded to the frame
of the mobile home and use only Listed pellet vent
Class “L” or “PL” connector pipe.
Outside Air Kit, part OAK-ACC must be installed in a
mobile home installation.
F. Sleeping Room
When installed in a sleeping room it is recommended that
3ft of vertical be installed prior to horizontally exiting the
room and a smoke/CO alarm be installed in the bedroom.
The size of the room must be at least 50ft³ per 1,000 Btu/hr
stove input, if the stove exceeds the room size, out air must
be installed.
G. California - Prop65
WARNING
This product and the fuels used to operate this product (wood), and
the products of combustion of such fuels, can expose you to
chemicals including carbon black, which is known to the State of
California to cause cancer, and carbon monoxide, which is known to
the State of California to cause birth defects or other reproductive
harm. For more information go to: WWW.P65Warnings.ca.gov
NOTE: Hearth & Home Technologies, manufacturer
of this appliance, reserves the right to alter
its products, their specications and/or price
without notice.
WARNING
Fire Risk.
Hearth & Home Technologies disclaims any
responsibility for, and the warranty will be
voided by, the following actions:
Installation and use of any damaged appliance.
Modication of the appliance.
Installation other than as instructed by Hearth &
Home Technologies.
Installation and/or use of any component part not
approved by Hearth & Home Technologies.
Operating appliance without fully assembling
all components.
Operating appliance without legs attached (if
supplied with appliance).
Do NOT Over re - If appliance or chimney
connector glows, you are over ring.
Any such action that may cause a re hazard.
9September 26, 2019 7050-802C
SANTA FE FREESTANDING
User Guide
2 Operating Instructions
A. Fire Safety
To provide reasonable re safety, the following should be
given serious consideration:
Install at least one smoke detector and CO
monitor on
each oor of your home.
Locate detectors away from the heating appliance and
close to the sleeping areas.
Follow the detector’s manufacturer’s placement and
installation instructions and maintain regularly.
Conveniently locate a Class A re extinguisher to
contend with small res.
In the event of a hopper re:
- Evacuate the house immediately.
- Notify re department.
D. Fuel Material and Fuel Storage
Pellet fuel quality can greatly uctuate. This appliance
has been designed to burn a wide variety of fuels, giving
you the choice to use the fuel that is most economical in
your region.
Hearth & Home Technologies strongly recommends only
using Pellet Fuel Institute (PFI) certied fuel.
Fuel Material
Made from sawdust or wood by-products
Depending on the source material it may have a high or
low ash content.
Higher Ash Content Material
Hardwoods with a high mineral content
Fuel that contains bark
Standard grade pellets, high ash pellets
Lower Ash Content Material
Softwoods
Fuels with low mineral content
Premium grade pellets
Corn
Moisture content must be 15% or less
Corn must be free of debris. Never burn corn straight
from the eld. It will clog the auger mechanism.
Corn with excessive grain dust must be screened by
sifting with 3/16 (4.76mm) inch mesh screening
Do no sue corn that contains additives such as
oils or means or has been chemically treated with
pesticides. It will void your warranty and destroy the
exhaust system.
Visit www.quadrare.com/shopping-tools/videos to view
product and use & care videos.
B. Non-Combustible Materials
Material which will not ignite and burn, composed of any
combination of the following:
- Steel
- Plaster
- Brick
- Iron
- Concrete
- Tile
- Glass
- Slate
Materials reported as passing ASTM E 136, Standard
Test Method for Behavior of Metals, in a Vertical Tube
Furnace of 750° C.
C. Combustible Materials
Material made of/or surfaced with any of the
following materials:
- Wood
- Compressed Paper
- Plant Fibers
- Plastic
- Plywood/OSB
- Sheet Rock (drywall)
Any material that can ignite and burn: ame proofed or
not, plastered or non-plastered.
Do not burn fuel that contains an additive; (such as
soybean oil).
May cause hopper res
Damage to product may result
Read the ingredients list on the package.
CAUTION!
WARNING
Risk of Chemical Poisoning!
Do NOT burn treated seed corn
Chemical pesticides are harmful or fatal if swallowed
Burning treated seed corn will void your warranty
WARNING
Fire Risk.
Do not operate appliance before reading
and understanding operating instructions.
Failure to operate appliance properly may
cause a house re.
10 September 26, 20197050-802C
SANTA FE FREESTANDING
Clinkers
Minerals and other non-combustible materials such as sand
will turn into a hard, glass-like substance called a clinker
when heated in the re pot.
Trees from dierent areas will vary in mineral content. That
is why some fuels produce more clinkers than others.
Moisture
Always burn dry fuel. Burning fuel with high moisture
content takes heat from the fuel and tends to cool the
appliance, robbing heat from your home. Damp pellet fuel
can clog the feed system.
Size
Pellets are either 1/4 inch or 5/16 inch (6-8mm)
in diameter
Length should be no more that 1-1/2 inches (38mm)
Pellet lengths can vary from lot to lot from the
same manufacturer
Due to length variations, the ame height (feed rate)
may need adjusting occasionally (See page 25
for instructions).
Performance
Higher ash content requires the ash drawer to be
emptied more frequently
Hardwoods require more air to burn properly
Premium wood pellets produce the highest heat output.
Burning pellets longer than 1-1/2 inches (38mm)
can cause an inconsistent fuel feed rate and/or
missed ignitions.
We recommend that you buy fuel in multi-ton lots
whenever possible. However, we do recommend trying
various brands before purchasing multi-ton lots to ensure
your satisfaction.
Changing to Dierent Fuel Type
Empty the hopper of the previous fuel
Thoroughly vacuum hopper before lling with the
new fuel
The burn rate, BTU content and heat output will all vary
depending on the fuel selected.
E. Before Your First Fire
1. First, make sure your appliance has been properly
installed and that all safety requirements have been
met. Pay particular attention to the re protection,
venting and thermostat installation instructions.
2. Double check that the ash drawer and rebox
are empty!
3. Close the front door.
IMPORTANT DETAIL: The tip of the thermocouple must
be in contact with the inside end of the thermocouple
cover or missed ignitions can occur.
F. Filling the Hopper
Open the hopper lid by lifting the handle. Fill the hopper
with fuel. Close the hopper lid. The appliance will not feed
with the hopper lid open.
Storage
Wood pellets should be left in their original sealed bag
until using to prevent moisture absorption.
This will also prevent rodents from becoming
a problem
.
Do not store any pellet fuel within the clearance
requirements or in an area that would hinder routine
cleaning and maintenance.
Tested and approved for wood pellets and shelled corn.
Burning of any other type of fuel voids your warranty.
CAUTION
11September 26, 2019 7050-802C
SANTA FE FREESTANDING
High
Med
Low
Heat Output Switch
Reset Button
Reset
Button
Combustion Blower
Convection Blower
Figure 11.1
G. General Operating Information
1. Thermostat Calls For Heat
The appliance is like most modern furnaces; when the
thermostat calls for heat, your appliance will automatically
light and deliver heat. When the room is up to temperature
and the thermostat is satised, the red call light will go o
and the appliance will shut down.
2. Heat Output Controls
This appliance is equipped with a heat output control switch
that has three settings or burn rates; low, medium and
high. The appliance will turn on and o as the thermostat
demands. When the thermostat calls for heat, the
appliance will start up at the burn rate for which it is set. If
the appliance is set at one of the lower settings, it will run
quieter but take longer to heat up an area than if it were set
at a higher burn rate. Regardless of the burn rate, when
the area is warm enough to satisfy the thermostat, the
appliance will shut o (Figure 11.1).
H. Starting Your First Fire
1. A thermostat is required for proper operation of this
appliance. At this time, ll the hopper with pellets, set
the thermostat to its lowest setting. Plug the power cord
into nearby outlet.
2. The exhaust blower will stay on for approximately 18
minutes even though the thermostat is not calling for
heat. This is normal.
3. L
ocate the heat output control switch mounted on the
back of the appliance in the upper right corner (Figure
11.1). Turn it to the “high” setting by pushing the top of
the control switch in and then adjust the thermostat to
its highest setting. Remove the right side panel and the
red call light located to the left of the control box will be
on (Figure 11.2). This indicates the thermostat is calling
for heat.
4. The fuel feed system and the igniter should
now
be on.
5. For your rst re it will be necessary to press the reset
button once approximately 2 minutes after start up
and again in 5 minutes. This will ll the feed system
and allow the appliance to begin dropping pellets. The
appliance will continue to run as long as the thermostat
is calling for heat.
6. Once the appliance has ignited, let it burn for
approximately 15 minutes, then set the thermostat to
the desired room temperature. Adjust the heat output
control switch to the desired setting.
Figure 11.2
WARNING
Fire Hazard.
Keep combustible materials, gasoline and
other ammable vapors and liquids clear of
appliance.
Do NOT store ammable materials in the
appliance’s vicinity.
NEVER use gasoline, GASOLINE-TYPE lantern fuel,
kerosene, charcoal lighter uid, or similar liquids to
start or “freshen up” a re in this appliance. Keep all
such liquids well away from the appliance while it is
in use.
DO NOT BURN GARBAGE OR FLAMMABLE
FLUIDS SUCH AS GASOLINE, NAPHTHA OR
ENGINE OIL.
DO NOT USE CHEMICALS OF FLUIDS TO START
THE FIRE.
Combustible materials may ignite.
WARNING
Fire Risk
Do NOT operate appliance:
With appliance door open.
Fire pot oor open.
Cleaning slide plates open.
Do NOT store fuel:
Closer than required clearances to
combustibles to appliance
Within space required for loading or
ash removal.
12 September 26, 20197050-802C
SANTA FE FREESTANDING
Figure 12.3
Feed Adjustment Control Rod
Set Screw
Wing Nut
J. Feed Rate Adjustment Instructions
The feed adjustment control rod is factory set, and should
be adequate for most fuels. However, if the ame height
is too high or too low, you will need to adjust the feed rate.
Wait until the appliance has been burning for 15 minutes
before making your adjustments and allow 15 minutes for
feed adjustment to take eect.
1. Loosen the wing screw.
2. Adjust the feed adjustment control rod upward to
increase the feed rate and ame height or down, to
decrease the feed rate and ame height.
3. Re-tighten the wing screw.
I. Fire Characteristics
A properly adjusted re with the heat output control switch
set on “high” has a short active ame pattern that extends
out of the re pot approximately 4 inches (102mm). If the
re has tall ames with black tails and seems somewhat
lazy, the feed rate will need to be reduced. This is done
by sliding the fuel adjustment control rod down, which will
reduce the feed. If the re is not 4 inches (102mm) tall,
slide the fuel adjustment control rod up to increase the
feed. A medium and low setting will give a shorter ame.
The ame will rise and fall somewhat. This is normal.
NOTE: We recommend the use of a 50-50 blend of corn
and wood pellets. The only change in operation
is that the feed rate may require a slight
adjustment. If the appliance is running all of the
time, 100% corn will work after the re has been
started using wood pellets.
Tall, Lazy Flame, Orange in Color
Incorrect
Correct Flame Size, Yellow/White in Color
Correct
Figure 12.1
Figure 12.2
WARNING
Fire Risk.
High ask fuels, or lack of maintenance,
can cause the re pot to ll with ash
and clinker. If the re pot lls to the top,
immediately shut down the appliance
and clean.
Failure to do so could result in smoking,
sooting and possible hoper res.
13September 26, 2019 7050-802C
SANTA FE FREESTANDING
K. Ignition Cycles
1. At the beginning of each ignition cycle, it is normal to
see some smoke in the rebox. The smoke will stop
once the re starts.
2. The convection blower will automatically turn on after
your appliance has been burning for approximately
10 minutes. This blower transfers heat from your
appliance into the room, and will continue to run after
the thermostat has stopped calling for heat until the
appliance has cooled down.
3. Occasionally the appliance may run out of fuel and
shut itself down. When this happens, the red call
light will be on (See Figure 11.1 on page 11). To
restart it, ll the hopper and press the reset button
(See Figure 10.1, page 10). When you press the reset
button the red call light will go out. Release the button
and the light will come back on. You should see a re
shortly. If not, follow the instructions on page 8, of
“Starting Your First Fire”.
M. Clear Space
Mantel: Avoid placing candles and other heat-sensitive
objects on mantel or hearth. Heat may damage
these objects.
L. Restarting the Appliance
Restart Process
1. When the unit has run out of fuel, add pellet fuel to
the hopper.
2. Dump the ashes and clinkers built up in the re pot by
pulling the ash dump removal handle out several times.
Make sure clinkers have dropped into the ash pan then
return the handle to fully closed position.
3. Press the reset button
4. The appliance will then being its startup sequence..
Restarting After a Power Failure
1. For an electrical disruption the appliance will start on its
own - providing the thermostat is asking for heat.
NOTICE: Clearances may only be reduced by means
approved by the regulatory authority
having jurisdiction.
WARNING
Fire Risk
Do NOT operate appliance:
With appliance door open.
Fire pot oor open.
Cleaning slide plates open.
Do NOT store fuel:
Closer than required clearances to
combustibles to appliance
Within space required for loading or
ash removal.
Fire Risk.
Do NOT place combustible objects in front of
the appliance. High temperatures may ignite
clothing, furniture or draperies. Maintain a
minimum clearance of 3 feet (914mm) in front
of appliance.
WARNING
Fire Risk.
Keep combustible materials, gasoline and
other ammable vapors and liquids clear
of appliance.
WARNING
Do NOT store ammable materials in the
appliance’s vicinity.
DO NOT USE GASOLINE, LANTERN FUEL,
KEROSENE, CHARCOAL LIGHTER FLUID OR
SIMILAR LIQUIDS TO START OR “FRESHEN UP”
A FIRE IN THIS Appliance.
DO NOT BURN GARBAGE OR FLAMMABLE
FLUIDS SUCH AS GASOLINE, NAPHTHA OR
ENGINE OIL.
DO NOT USE CHEMICALS OR FLUIDS TO START
THE FIRE.
Keep all such liquids well away from the appliance
while it is in use.
Combustible materials may ignite.
HOT WHILE IN OPERATION. KEEP CHILDREN,
CLOTHING AND FURNITURE AWAY. CONTACT MAY
CAUSE SKIN BURNS.
CAUTION
14 September 26, 20197050-802C
SANTA FE FREESTANDING
N. Thermostat Controls
TEMPERATURE (HEAT / OFF) SWITCH:
Set this switch to HEAT to control your appliance. The o
position will disable the appliance.
SET (MULTI- FUNCTION) SLIDE SWITCH:
This provides easy access to common settings, and should
always remain in RUN unless items are being adjusted.
Figure 14.1
O. Thermostat Setup Options
Setup options for how the thermostat will function are
performed using a menu on the display screen.
TO ACCESS THE SETUP MENU:
Move the TEMPERATURE switch into the OFF position,
and then hold down the COPY button for approximately 5
seconds until the screen changes. The menu will always
start with item #01, and is advanced to each following item
by a single press of the NEXT button. The options for each
item are changed using the UP or DOWN buttons.
ITEM #01 (CLK = CLOCK FORMAT):
12Hr, default: This displays the clock times using
standard AM and PM values.
24Hr: This displays the clock times using the military-
time format (example 22:00 hours, without using AM
or PM).
ITEM #02 (TMP = TEMPERATURE SCALE):
F, default: Shows all temperature values in Fahrenheit.
C: Shows all temperature values Celsius.
ITEM #03 (PROGRAMMING STYLE):
7 Day, default: This style uses a separate program
routine for each of the 7 days in the week.
5/2 Day: This style uses a weekday program routine
for Monday, Tuesday, Wednesday, Thursday, Friday,
and a separate weekend program routine for Saturday
and Sunday.
Manual Non-Programmable: In this setting, there are
no program routines for the thermostat to follow and
the temperature control will be set only by the UP and
DOWN buttons on the front panel.
ITEM #04 (PERD = EVENT OR PERIOD QUANTITY):
4P, default: Thermostat uses four Events per day
(called MORN, DAY, EVE, and NITE).
2P: The thermostat uses two Events per day (called
DAY and NITE).
NOTE: When thermostat is set to “Manual” non-
programmable mode, all positions of the SET
slide switch will act like RUN.
UP / DOWN BUTTONS:
The UP and DOWN buttons are used to control the set
temperature, or adjust any other on-screen items. An
items ashing, is the item currently being adjusted.
HOLD BUTTON:
This button activates and deactivates the manual
Temperature HOLD feature, which maintains a
xed set temperature indenitely without following a
program routine.
COPY BUTTON:
This is used to copy temperature program items from one
day to the next. Also used to to access the menu setup.
NEXT BUTTON:
This is used when setting items such as software options,
and temperature programs when they are ashing on the
screen. Pressing the NEXT button will cycle through which
item is ashing.
NOTE: Event or Period Quantity feature is not accessible
during Manual Non-Programmable mode.
ITEM #07 (DLAY = DELAY TIME):
5, default: Thermostat waits 5 minutes before turning
the system back on after it was last run. This internal
delay prevents the appliance from turning on too
quickly after shutting down. The 5 minute setting is ne
for most applications.
2: Same operation as above but reduced to 2 minutes
between state changes.
NOTE: There is no delay available when the thermostat
is manually turned up and down.
15September 26, 2019 7050-802C
SANTA FE FREESTANDING
Table 15.1
ITEM #08 (TEMPERATURE DIFFERENTIAL):
The thermostat works by turning your heating system
on and o whenever the room temperature varies from
the desired set-point temperature.
Use the UP/DOWN buttons to change the number
value between 1 and 9. Generally your system
should cycle on about 3 to 6 times per hour. A smaller
dierential number makes the system cycle more
frequently, so the room temperature is more precise
and constant. A larger dierential number will make the
system remain on for a longer duration each time and
decreases the number of cycles per hour.
Default is set to 4.
P. Thermostat Operation Instructions
SET DAY AND TIME:
Place the SET switch into the DAY/TIME position. With
the day ashing press UP or DOWN to set the day or the
week. Press NEXT and the clock time will start ashing.
Use UP or DOWN to set the time; verify the AM/PM
indicator is correct. Return the SET switch to RUN position
when nished.
HEATING:
Basic operation of the thermostat can be obtained with
the SET switch in the RUN position. The temperature
can be adjusted using the UP and DOWN buttons.
When the thermostat is rst powered on, it will follow a
default temperature routine that is preset from the factory
(Table 15.1).
LCD DISPLAY BACK LIGHT:
The display screen is lighted to assist viewing at nighttime,
or in locations with low light levels. Press any button on
the front panel to activate the approximate 10 second
back light.
TEMPERATURE OVERRIDE:
While thermostat is in RUN mode, the set temperature
can be temporarily changed by pressing UP or DOWN.
The temporarily changed set temperature will return to the
programmed value stored in memory when start time of
the next upcoming scheduled event is reached (MORN,
DAY, EVE, OR NITE). While the temporary changed set
temperature is in eect, the word OVERRIDE will be shown
on the display screen. To cancel, move TEMPERATURE
switch to OFF and back to HEAT again.
TEMPERATURE HOLD:
Temperature hold is used for maintaining a xed set
temperature; once a HOLD is initiated, the thermostat will
maintain the set temperature indenitely. To enter a HOLD
state, press the HOLD button one time and the word HOLD
will appear on the display. To cancel, press the HOLD
button once again.
Q. Thermostat Temperature Programs
The thermostat by default has 4 separate program events
they are: MORN, DAY, EVE, and NITE. Each event ends at
the start time of the following event.
NOTE: When the last event is nished for each day
or group of days, the thermostat will advance
forward into the next day or group of days.
6. Use steps 3 through 5 to set up the events for the rest
of the week or group of days.
7. Return the SET switch back to RUN.
NOTE: If the thermostat is set for 2 events a day instead
of 4, the thermostat will only use the DAY and
NITE events.
SET TEMPERATURE PROGRAMS:
1. Move TEMPERATURE switch to HEAT.
2. Move SET switch to TEMP PROG position.
3. Starting with Monday, use the UP or DOWN buttons to
adjust the start time and set temperature for the MORN
event, and then press NEXT button to advance.
4. Adjust the start time and set temperature of the DAY
event then press NEXT button.
5. Continue in this same manner to adjust the start time
and set temperatures for the EVE and NITE events
for Monday.
Event Time Temperature
MORN 6:00 AM 70°F (21°C)
DAY 8:00 AM 62°F (17°C)
EVE 6:00 PM 70°F (21°C)
NITE 10:00 PM 62°F (17°C)
STATIC NOTICE
Thermostat is protected against normal static electric
discharges, however to minimize the risk of damaging
the thermostat in extremely dry weather, please touch a
grounded metal object before touching the thermostat.
16 September 26, 20197050-802C
SANTA FE FREESTANDING
R. Thermostat Other Features
TEMPERATURE CALIBRATION:
The internal temperature sensor in this thermostat is
accurately calibrated at the factory, and in most cases
alterations to this setting should not be needed. The
temperature calibration feature allows you to manually
oset the measured temperature by as much as plus
or minus 5°F (3°C) from its original value. If several
thermostats are used in the same house, this feature can
be used to synchronize this thermostat to the others.
Change the temperature calibration:
1. Move TEMPERATURE switch to OFF.
2. Move SET switch to RUN.
3. Press and hold both UP and DOWN buttons together
for at least 5 seconds; the words SET and CAL will
appear on the display along with a single ashing
temperature digit.
4. Use the UP or DOWN buttons to change the number of
degrees desired for adjustment; 0° is the default value
and also means no correction will be applied.
5. Press the NEXT button to accept the setting.
NOTE: All other features need to be completed in a
timely manner as the thermostat will time out
after 10 seconds.
COPY PROGRAM FEATURE:
Using similar instructions as SET TEMPERATURE
PROGRAMS the COPY button will allow a whole day of
set program events to be copied to another day.
1. Move TEMPERATURE switch to HEAT as well as
move SET switch to TEMP PROG position.
2. Starting with Monday, use the UP or DOWN buttons
to adjust the start time and set temperature for the
MORN, DAY, EVE, and NITE events. Press the COPY
button and then press the NEXT button to advance
to Tuesday.
3. With Tuesday displayed press COPY button. As
all programs events from Monday will be copied to
Tuesday (this will advance automatically to the next
day; Wednesday, as the word COPY will appear on the
screen for one second).
4. Continue in this pressing COPY button to set desired
days with original setting.
NOTE: The word COPY will not appear on the display
for Monday, but will display each day afterwards
for approximately one second and the day of the
week will automatically advance forward to the
next day.
KEYPAD LOCKOUT:
There is the option to lock the front panel buttons to prevent
unauthorized tampering of your thermostat settings.
To Lock the Keypad:
1. Move TEMPERATURE switch to HEAT.
2. Move SET switch to RUN.
3. Perform a single press of each button in the following
sequence:
- NEXT, NEXT, NEXT, HOLD
A padlock will appear on the display screen.
To Unlock the Keypad:
1. Move TEMPERATURE switch to HEAT.
2. Move SET switch to RUN.
3. Perform a single press of each button in the following
sequence:
- NEXT, NEXT, NEXT, HOLD
A padlock will no longer be present on the display screen.
HW
RST
HARDWARE RESET:
The hardware reset button; labeled HW RST, is a small
round push button that is located in the middle of the circuit
board, just below the battery holder (Figure 15.1). Pressing
this button will:
Cause the LCD display screen to become
fully populated
Thermostat to perform an internal system check of
its components
If the thermostat appears to be acting in an erratic manner,
pressing the HW RST button may remedy this behavior.
The temperature programs are not erased when a
hardware reset is performed, however the clock will have to
be changed to match the current day and time.
Figure 16.1
SOFTWARE RESET:
Software reset is used to erase ALL temperature events,
and to return all user-adjustable software settings back to
their original factory default settings.
To Perform a Software Rest:
1. Verify the thermostat’s keypad is not locked.
2. Move TEMPERATURE switch to OFF.
3. Press and hold the UP, DOWN, and NEXT buttons all
at the same time for at least 5 seconds. When the LCD
display screen will become fully populated let go of all
buttons at that point the screen will return to normal.
The clock will have to be changed to match the current day
and time.
17September 26, 2019 7050-802C
SANTA FE FREESTANDING
S. Thermostat Battery Replacement
This thermostat is powered by two “AA” Alkaline batteries.
The batteries should be replaced AT LEAST once per
year to ensure reliable operation or sooner if the LO BATT
appears on the display screen. The batteries are located
on the back of the thermostat’s circuit board. The front
portion of the thermostat can be removed from the back
half by using the tabs on the top edge of the thermostat
housing (Figure 17.1).
Figure 17.1
Figure 17.4
Figure 17.2 - Full battery icon
Figure 17.3 - Low battery icon
CONNECT THERMOSTAT WIRES TO APPLIANCE:
There is a 4 screw terminal block located on the back
lower left corner of the stove directly above the power
cord inlet. The center 2 screws are for the thermostat
wires (Figure 17.4).
When installing new batteries, it is recommended using
only brand new “AA” size alkaline batteries. Please verify
the polarity markings shown in the battery compartment
before adding batteries to the compartment. When nished,
line up the front of the thermostat to the base, and rmly
press together to securely latch the front and back halves
together properly.
BATTERY GRAPHIC:
Anytime time the batteries are physically present in
the thermostat, there will be a visual indicator showing
the life of the battery. This will appear on the display
screen (Figures 16.2 & 16.3).
TERMINAL BLOCK
CENTER 2 SCREWS FOR
THERMOSTAT WIRES
POWER OUTLET
Shock hazard.
Do NOT remove grounding prong
from plug.
Plug directly into properly grounded 3
prong receptacle.
Route cord away from appliance.
Do NOT route cord under or in front
of appliance.
CAUTION
18 September 26, 20197050-802C
SANTA FE FREESTANDING
T. Frequently Asked Questions
What causes my glass to become dirty?
If the glass has white ash build up it is normal and the glass should be cleaned. If it is a black soot build up airow through
the unit may be restricted. The most often cause is overdue maintenance and cleaning. See “Maintaining and Servicing
Appliance” and/or make adjustments to the trim control.
How can I get more heat out of the appliance?
The most often cause of diminished heat output is overdue maintenance and cleaning. See “Maintaining and Servicing
Appliance”.
What should I do if I smell smoke or there is ash/soot coming from the appliance?
While there will always be some smoke smell from wood burning appliances (including pellet) you should investigate all
venting to make sure it is sealed properly. Most vent ing requires silicone to seal the seams.
In addition most homes are built very tight today and with exhaust systems can create negative pressure in the home. See
“Negative Pressure” under “Getting Started” in the owner’s manual if you have checked the venting but still have smoke
coming from the appliance. For ash or soot check the above and the exhaust blower housing and seals.
Why would my appliance run ne last winter but not start this fall?
It is possible that the stove was not properly prepared for the Non-burn season (see troubleshooting section).
Is there a place to lubricate the blowers to quiet them down?
No. The most often cause of noisy blowers is from the impellers becoming dirty over time. See maintenance and service
section for maintaining and servicing.
What is the metal object with the bend in it that came inside the plastic bag?
It is a clean-out tool used to help clean the re pot and remove any jams in the rare event they occur in the feed tube.
Why is there a black residue building up on the outside of my home?
Wind can cause this to happen. If the appliance is oper ating correctly very little soot should ever exit the termina tion cap.
Check to be sure the venting is installed per the owner’s manual and local codes.
Do I need an outside air kit?
Outside air is required for mobile home installs and in some jurisdictions. Refer to “Listing & Code Approvals”,“ Mobile
Home Installation” and “ Appliance Set-up”. Also refer to local building codes.
I am seeing sparks coming out of my pipe (termination cap) outside is this safe?
This is normal. As long as clearances to combustibles were followed this is safe.
I have no power to anything. Does this unit have a circuit breaker or fuse or a reset button?
This unit has one fuse on the control board and a resettable snap disc mounted to the feed tube. If the appliance
overheats then the snap disc can be reset; if the fuse is blown the control board must be replaced.
Can I burn corn in my unit?
Yes, this appliance can burn corn type fuel at a 1:1 ratio.
Where is the serial # located on my unit?
Freestanding - the serial number is located on the back of the stove.
No pellets are dropping in my re pot.
See troubleshooting guide.
Contact your dealer for additional information regarding operation and troubleshooting.
Visit www.quadrare.com to locate a dealer.
19September 26, 2019 7050-802C
SANTA FE FREESTANDING
3 Maintenance and Service
B. Quick Reference Maintenance Chart
NOTICE: These are recommendations. Clean more frequently if you encounter heavy build-up of ash at the
recommended interval or you see soot coming from the vent. Not properly cleaning your appliance
on a regular basis will void your warranty.
Cleaning or Inspection Frequency Daily Weekly
Every 2
Weeks
Monthly Yearly
Ash Pan - Burning Wood Pellets Every 5 bags of fuel OR X
Ash Pan - Burning Alternate
Fuels
Every 1 bag of fuel OR X
Ash Removal from Firebox
More frequently depending
on the fuel type or ash build-
up
OR X
Blower, Combustion (Exhaust)
More frequently depending
on the fuel type
OR X
Blower, Convection
More frequently depending
on the operating environment
OR X
Door Latch Inspection Prior to heating season OR X
Firebox - Prepare for Non-Burn
Season
At end of heating season OR X
Fire pot - Burning Softwood
Pellets
Every 5 bags OR X
Fire pot - Burning Hardwood
Pellets
Every 3 bags OR X
Fire pot - Burning Alternate Fuels Every 1 bag OR X
Glass
When clear view of re pot
becomes obscured
OR X
Heat Exchanger & Drop Tube Every 1 ton of fuel OR X
Hopper
Every 1 ton of fuel or when
changing fuel types
OR X
Venting System
More frequently depending
on the fuel type
OR X
Follow the detailed instructions found in this section for each step listed in the chart below.
A. Proper Shutdown Procedure
Turn o the thermostat.
This pellet appliance has a manufacturer-set minimum
low burn rate that must not be altered. It is against
federal regulations to alter this setting or otherwise
operate this pellet appliance in a manner inconsistent
with operating instructions in this manual.
When properly maintained, your replace will give
you many years of trouble-free service. Contact your
dealer to answer question regarding proper operation,
troubleshooting and service for your appliance. Visit
www.quadrare.com/owner-resources to view basic
troubleshooting, FAQs, use & care videos. We recommend
annual service by a qualied service technician.
Table 19.1
Shock and Smoke Hazard
Turn down thermostat, let appliance
completely cool and exhaust blower must
be o. Now you can unplug appliance
before servicing.
Smoke spillage into room can occur if
appliance is not cool before unplugging.
Risk of shock if appliance not unplugged
before servicing appliance.
CAUTION
20 September 26, 20197050-802C
SANTA FE FREESTANDING
C. General Maintenance and Cleaning
1. Types of Fuel
The type of fuel you are burning will dictate how often you
have to clean your re pot.
If the fuel you are burning has a high dirt or ash content or
you are burning shelled eld corn, it may be necessary to
clean the re pot more than once a day.
Dirty fuel will cause clinkers to form in the re pot. A clinker
is formed when dirt, ash or a non-burnable substance is
heated to 2000°F (1093°C) and becomes glass-like. See
page 34 in this section for more details on fuels with high
ash content.
2. Cleaning Fire pot with Cleaning Rod & Fire pot
Scraper
Frequency: Daily or more often as needed
By: Homeowner
a. The appliance must be in complete shutdown and
cool and the exhaust blower o. If you are just
cleaning the re pot, there is no need to unplug the
appliance.
b. Pull re pot cleaning rod OUT a couple of times to
help shake debris loose. If rod is hard to pull, it may
be necessary to use your re pot clean-out tool to
chip away material that has built up on the bottom
plate of the re pot and to push out any clinkers.
Larger clinkers may have to be removed from the
top of the re pot. Corn clinkers can be especially
dicult to break up.
c. The re pot oor plate must be fully closed when
nished (Figure 20.1).
3. Ash Removal from Firebox
Frequency: Every 5 bags or weekly or more frequently
depending on ash build-up.
By: Homeowner
a. There must not be any hot ashes in the rebox
during cleaning so allow the appliance to
completely cool. Frequent cleaning of the ash in
the rebox will help slow down the build-up of ash
in the exhaust blower and vent system.
b. Plug in your appliance, if unplugged, and turn the
thermostat on and immediately shut it o to start
the exhaust blower on its cycle time. It will pull y
ash out the exhaust instead of into the room.
c. Open door. There are 2 cleaning slide plates to
the left and right of the re pot with nger holes.
Pull both slide plates out and sweep the remaining
ash from the rebox into the 2 open holes. A paint
brush works well for this. Close slide plates.
d. This ash is deposited in the same ash drawer
as the re pot debris. The ash drawer should
be emptied every time you clean the rebox.
Remember to place the ash and debris into a metal
or non-combustible container.
e. The 2 cleaning slide plates must be fully closed
when cleaning is complete.
4. Cleaning Ash Pan
Frequency: Weekly or every 5 bags of fuel
By: Homeowner
Locate the ash pan underneath the re pot. Open the
bottom ash door and slide the ash pan straight out. Empty
into a non-combustible container and re-install ash pan
(See Disposal of Ashes on page 20).
Back side of Firepot
Firepot floor left open
Figure 20.1
WARNING
Fire Risk
The cleaning slide plates must be fully
CLOSED when appliance is operating.
Hot pellets may fall into ash pan and start
a re.
WARNING
Fire Risk
NEVER pull re pot cleaning rod or
cleaning slide plates out when appliance
is operating.
The cleaning slide plates must be fully
CLOSED when appliance is operating.
Hot pellets may fall into ash pan and start
a re or mis-starts due to lack of vacuum.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40

Quadrafire Santa Fe Pellet Stove Manuel utilisateur

Catégorie
Poêles
Taper
Manuel utilisateur

dans d''autres langues