Castle Pellet Stoves 41278 CASTLE SERENITY 2.0 Le manuel du propriétaire

GAS/OIL

RATIO

50:1

P/N: 41723

ECN: 14356

REV4: 06/16/2023

Get parts online at

www.CastleStoves.com

Operator's Manual

Serenity

Pellet Stove

Model 41278

ENGLISHENGLISHFRANÇAIS

CAUTION

CONTACT LOCAL BUILDING OR FIRE OFFICIALS ABOUT RESTRICTIONS

AND INSTALLATION INSPECTION REQUIREMENTS FOR YOUR AREA.

ATTENTION

CONSULTER LES SERVICES DU BÂTIMENT OU D’INCENDIE LOCAUX

CONCERNANT LES RESTRICTIONS ET LES EXIGENCES D’INSPECTION

D’INSTALLATION EN VIGUEUR.

CAUTION

DO NOT DISCARD MANUAL!

IMPORTANT OPERATING AND

MAINTENANCE INSTRUCTIONS

INCLUDED.

SAVE THESE INSTRUCTIONS AND

LEAVE THIS MANUAL WITH ANY

PERSON RESPONSIBLE FOR USE AND

OPERATION.

ATTENTION NE PAS JETER!

IMPORTANTES INSTRUCTIONS

D’UTILISATION ET D’ENTRETIEN

INCLUSES.

CONSERVEZ CES INSTRUCTIONS

ET LAISSEZ CE MANUEL À TOUTE

PERSONNE RESPONSABLE

DE L’UTILISATION ET DU

FONCTIONNEMENT.

WARNING

PLEASE READ THIS ENTIRE

MANUAL BEFORE INSTALLATION

AND USE OF THIS PELLET

FUELBURNING ROOM HEATER.

FAILURE TO FOLLOW THESE

INSTRUCTIONS COULD RESULT

IN PROPERTY DAMAGE, BODILY

INJURY OR EVEN DEATH.

AVERTISSEMENT

VEUILLEZ LIRE CE MANUEL EN

ENTIER AVANT D’INSTALLER

ET D’UTILISER CET APPAREIL

DE CHAUFFAGE AUTONOME À

GRANULES, AFIN D’ÉCARTER LES

RISQUES DE DÉGÂTS MATÉRIELS,

DE BLESSURES CORPORELLES,

VOIRE DE MORT.

Check for parts online at www.castlestoves.com or call 800-345-6007 M-F 8-5

2

Operator's Manual

Serenity Pellet Stove

WARNINGS AND SAFETY PRECAUTIONS

Owner’s Responsibility

• Accurate assembly and safe and eective use of the

stove is the owner’s responsibility.

• Read and follow all safety instructions.

• Carefully follow all assembly instructions.

• Maintain the stove according to directions and sched-

ule included in this Castle operator’s manual.

• Ensure that anyone who uses the stove is familiar with

all controls and safety precautions.

Special Messages

Your manual contains special messages to bring attention

to potential safety concerns, stove damage as well as helpful

operating and servicing information. Please read all the

information carefully to avoid injury and stove damage.

NOTE: General information is given throughout the

manual that may help the operator in the

operation or service of the stove.

IMPORTANT SAFETY PRECAUTIONS

Please read this section carefully. Operate the stove according to

the safety instructions and recommendations outlined here and

inserted throughout the text. Anyone who uses this stove must

read the instructions and be familiar with the controls.

WARNING INDICATES A SERIOUS INJURY

OR FATALITY COULD RESULT IF THE SAFETY

INSTRUCTIONS THAT FOLLOW THIS SIGNAL

WORD ARE NOT OBEYED.

WARNING

CAUTION INDICATES YOU CAN OR YOUR

EQUIPMENT CAN BE HURT IF THE SAFETY

INSTRUCTIONS THAT FOLLOW THIS SIGNAL

WORD ARE NOT OBEYED.

CAUTION

THIS SYMBOL POINTS OUT IMPORTANT SAFETY

INSTRUCTIONS WHICH IF NOT FOLLOWED

COULD ENDANGER YOUR PERSONAL SAFETY.

READ AND FOLLOW ALL INSTRUCTIONS IN THIS

MANUAL BEFORE ATTEMPTING TO OPERATE THIS

EQUIPMENT.

DANGER

DANGER INDICATES A SERIOUS INJURY

OR FATALITY WILL RESULT IF THE SAFETY

INSTRUCTIONS THAT FOLLOW THIS SIGNAL

WORD ARE NOT OBEYED.

WARNING

YOU MUST READ, UNDERSTAND AND

COMPLY WITH ALL SAFETY AND OPERATING

INSTRUCTIONS IN THIS MANUAL BEFORE

ATTEMPTING TO SETUP AND OPERATE YOUR

STOVE.

FAILURE TO COMPLY WITH ALL SAFETY AND

OPERATING INSTRUCTIONS CAN RESULT IN

SERIOUS PERSONAL INJURY TO YOU AND/OR

BYSTANDERS, AND RISK OF EQUIPMENT AND

PROPERTY DAMAGE. THE TRIANGLE IN THE

TEXT SIGNIFIES IMPORTANT CAUTIONS OR

WARNINGS WHICH MUST BE FOLLOWED.

IMPORTANT

IMPORTANT INDICATES HELPFUL INFORMATION

FOR PROPER ASSEMBLY, OPERATION, OR

MAINTENANCE OF YOUR EQUIPMENT.

3

Check for parts online at www.castlestoves.com or call 800-345-6007 M-F 8-5

Operator's Manual

Serenity Pellet Stove

ENGLISH

CAUTION

CHECK BUILDING CODES PRIOR TO INSTALLATION.

CONTACT THE REGULATING AUTHORITY PRIOR

TO INSTALLATION TO DETERMINE THE NEED FOR

A PERMIT.

INSTALLATION MUST COMPLY WITH LOCAL,

REGIONAL, STATE AND NATIONAL CODES AND

REGULATIONS

CONSULT LOCAL BUILDING OR FIRE OFFICIALS

ABOUT RESTRICTIONS AND INSTALLATION

INSPECTION REQUIREMENTS IN YOUR AREA.

TESTED AND APPROVED FOR PELLET FUEL.

BURNING ANY OTHER TYPE OF FUEL VOIDS

WARRANTY.

PLEASE READ THIS ENTIRE MANUAL BEFORE

INSTALLATION AND USE OF THIS PELLET FUEL

BURNING ROOM HEATER. FAILURE TO FOLLOW

THESE INSTRUCTIONS COULD RESULT IN

PROPERTY DAMAGE, BODILY INJURY OR EVEN

DEATH.

DO NOT STORE OR USE GASOLINE OR OTHER

FLAMMABLE VAPORS AND LIQUIDS IN THE

VICINITY OF THIS OR ANY OTHER APPLIANCE.

DO NOT OVERFIRE  IF ANY EXTERNAL PART

STARTS TO GLOW, YOU ARE OVERFIRING.

REDUCE FEED RATE. OVERFIRING WILL VOID THE

WARRANTY.

COMPLY WITH ALL MINIMUM CLEARANCES

TO COMBUSTIBLES AS SPECIFIED. FAILURE TO

COMPLY MAY CAUSE A HOUSE FIRE.

WARNING WARNING

HOT SURFACE ! DO NOT TOUCH! SEVERE BURNS

MAY RESULT. CLOTHING IGNITION MAY RESULT.

GLASS AND OTHER SURFACES ARE HOT DURING

OPERATION AND COOL DOWN.

KEEP CHILDREN AWAY.

CAREFULLY SUPERVISE CHILDREN IN SAME

ROOM AS APPLIANCE.

DO NOT OPERATE WITH PROTECTIVE BARRIERS

OPEN OR REMOVED.

KEEP CLOTHING, FURNITURE, DRAPERIES AND

OTHER COMBUSTIBLES AWAY.

DO NOT DISCARD

IMPORTANT OPERATING AND MAINTENANCE

INSTRUCTIONS INCLUDED.

READ, UNDERSTAND AND FOLLOW THESE

INSTRUCTIONS FOR SAFE INSTALLATION AND

OPERATION.

LEAVE THIS MANUAL WITH PARTY RESPONSIBLE

FOR USE AND OPERATION.

CAUTION

Check for parts online at www.castlestoves.com or call 800-345-6007 M-F 8-5

4

Operator's Manual

Serenity Pellet Stove

WARNING INDICATES A SERIOUS INJURY

OR FATALITY COULD RESULT IF THE SAFETY

INSTRUCTIONS THAT FOLLOW THIS SIGNAL

WORD ARE NOT OBEYED.

READ THIS ENTIRE MANUAL BEFORE YOU INSTALL

AND USE YOUR NEW PELLET STOVE. FAILURE TO

FOLLOW INSTRUCTIONS MAY RESULT IN PROPERTY

DAMAGE, BODILY INJURY, OR EVEN DEATH.

CHILDREN AND ADULTS SHOULD BE ALERTED TO

THE HAZARDS OF HIGH SURFACE TEMPERATURES

AND SHOULD STAY AWAY TO AVOID CONTACT TO

SKIN AND/OR CLOTHING.

YOUNG CHILDREN SHOULD BE CAREFULLY

SUPERVISED WHEN THEY ARE IN THE SAME ROOM

AS THE STOVE.

CLOTHING AND OTHER FLAMMABLE MATERIALS

SHOULD NOT BE PLACED ON OR NEAR THIS UNIT.

FLAMMABLE OR EXPLOSIVE LIQUIDS SUCH AS

GASOLINE, NAPHTHA, ALCOHOL, OR ENGINE OIL

MUST NEVER BE USED IN OR AROUND STOVE.

THESE LIQUIDS MUST BE STORED IN A SEPARATE

ROOM AS THE OPEN FLAME IN THE FIRE BOX COULD

IGNITE THE FUMES OF SUCH LIQUIDS.

DO NOT BURN GARBAGE IN THIS UNIT. THE

BURNING OF OTHER SOLID FUELS SUCH AS

CORD WOOD OR WOOD CHIPS IN THIS STOVE IS

NOT PERMITTED. ANY FUELS NOT CERTIFIED BY

CASTLE PELLET STOVES WHICH ARE BURNED IN

THIS STOVE WILL VOID THE WARRANTY.

DO NOT ROUTE POWER CORD IN HIGH TRAFFIC

AREAS. A POWER SURGE PROTECTOR PLUGGED

INTO A GROUNDED 120 VOLT POWER SOURCE IS

REQUIRED.

WARNING

DO NOT INSTALL A FLUE DAMPER IN THE EXHAUST

VENTING SYSTEM OF THIS UNIT.

DO NOT CONNECT THIS UNIT TO A CHIMNEY FLUE

SERVICING ANOTHER APPLIANCE.

DO NOT INSTALL IN A SLEEPING ROOM.

DO NOT CONNECT TO ANY AIR DISTRIBUTION DUCT

OR SYSTEM.

• DO NOT CONNECT DIRECTLY TO A MASONRY

CHIMNEY.

• DO NOT TERMINATE VENT IN ANY ENCLOSED

OR SEMIENCLOSED AREA, SUCH AS; CARPORTS,

GARAGE, ATTIC, CRAWL SPACE, UNDER A SUN

DECK OR PORCH, NARROW WALKWAY OR CLOSED

AREA, OR ANY LOCATION THAT CAN BUILD UP A

CONCENTRATION OF FUMES SUCH AS A STAIRWELL,

COVERED BREEZEWAY ETC.

• NEVER TOUCH DOOR LATCHES WHILE STOVE IS

IN OPERATION; THEY GET EXTREMELY HOT.

PROPER INSTALLATION OF THIS STOVE IS NECESSARY

FOR SAFE AND EFFICIENT OPERATION. INSTALLING THIS

PRODUCT IMPROPERLY MAY RESULT IN A HOUSE FIRE

AND PERSONAL INJURY.

ALL APPLICABLE BUILDING CODES FOR YOUR LOCATION

MUST BE FOLLOWED. IN AREAS WHERE BUILDING CODES

REQUIRE ADDITIONAL STEPS TO THE INSTALLATION

OF THIS PRODUCT NOT INCLUDED IN THIS MANUAL,

THE BUILDING CODES WILL TAKE PRECEDENT AND

MUST BE FOLLOWED. CONTACT YOUR LOCAL BUILDING

INSPECTOR TO OBTAIN ANY NECESSARY PERMITS OR

INSPECTION GUIDELINES BEFORE INSTALLING THE

PRODUCT.

5

Check for parts online at www.castlestoves.com or call 800-345-6007 M-F 8-5

Operator's Manual

Serenity Pellet Stove

ENGLISH

ALL APPLICABLE BUILDING CODES FOR YOUR

LOCATION MUST BE FOLLOWED. IN AREAS

WHERE BUILDING CODES REQUIRE ADDITIONAL

STEPS TO THE INSTALLATION OF THIS PRODUCT

NOT INCLUDED IN THIS MANUAL, THE BUILDING

CODES WILL TAKE PRECEDENT AND MUST BE

FOLLOWED. CONTACT YOUR LOCAL BUILDING

INSPECTOR TO OBTAIN ANY NECESSARY PERMITS

OR INSPECTION GUIDELINES BEFORE INSTALLING

THE PRODUCT.

CONTACT LOCAL BUILDING OR FIRE OFFICIALS

ABOUT RESTRICTIONS AND INSTALLATION

INSPECTION REQUIREMENTS IN YOUR AREA.

CONTACT YOUR LOCAL AUTHORITY SUCH

AS MUNICIPAL BUILDING DEPARTMENT, FIRE

DEPARTMENT, FIRE PREVENTION BUREAU, ETC.

TO DETERMINE THE NEED FOR A PERMIT.

THE CASTLE PELLET STOVES PELLET STOVE IS

DESIGNED TO BURN PELLET FUEL ONLY.

A WORKING SMOKE DETECTOR IS REQUIRED AND

MUST BE INSTALLED IN THE SAME ROOM AS THE

STOVE.

THIS STOVE IS NOT INTENDED FOR USE IN

COMMERCIAL APPLICATIONS.

DOOR AND ASH PAN MUST BE CLOSED AND

LATCHED DURING OPERATION.

NOTIFY YOUR INSURANCE COMPANY OF PELLET

STOVE INSTALLATION.

THIS INSTALLATION MUST CONFORM WITH

LOCAL CODES. IN THE ABSENCE OF LOCAL CODES

YOU MUST COMPLY WITH ASTM E1509, UM 84

HUD, AND UCL S6272000.

THE STRUCTURAL INTEGRITY OF THE

MANUFACTURED HOME FLOOR, WALL, AND

CEILING/ROOF MUST BE MAINTAINED.

KEEP COMBUSTIBLE MATERIALS SUCH AS

GRASS, LEAVES, ETC. AT LEAST THREE FEET AWAY

FROM THE FLUE OUTLET ON THE OUTSIDE OF THE

BUILDING.

THIS STOVE SHOULD NOT BE USED AS THE

ONLY SOURCE OF HEAT IN THE HOUSE. POWER

OUTAGES AND PERIODIC MAINTENANCE WILL

RESULT IN A TOTAL LOSS OF HEAT.

DO NOT LEAVE HOPPER DOOR OPEN.

INSTALLATION AND REPAIR OF THIS PELLET

STOVE SHOULD BE DONE BY A QUALIFIED SERVICE

PERSON. THE APPLIANCE SHOULD BE INSPECTED

BEFORE USE AND AT LEAST ONCE A YEAR BY A

QUALIFIED SERVICE PERSON. IT IS IMPERATIVE

THAT THE CONTROL COMPARTMENTS, FIRE BOX,

AND THE CIRCULATING AIR PASSAGEWAYS OF THE

STOVE BE KEPT CLEAN.

THE OPERATION OF EXHAUST FANS SUCH AS

BATHROOM FANS, ATTIC FANS, ETC. MIGHT

STARVE THE PELLET STOVE OF COMBUSTIBLE AIR

CREATING A NEGATIVE PRESSURE IN THE ROOM.

PROVIDE ADEQUATE VENTILATION OF THE ROOM

ACCOMPANYING THE PELLET STOVE. IF NOT, THE

PRESSURE SWITCH MAY SHUT OFF OPERATION OF

THE PELLET STOVE.

THE MOVING PARTS OF THIS STOVE ARE PROPELLED

BY HIGH TORQUE ELECTRIC MOTORS. THESE PARTS

CAN CAUSE SEVERE DAMAGE TO BODY PARTS

THAT GET NEAR THEM. KEEP ALL BODY PARTS

AWAY FROM AUGER AND FANS WHILE THE STOVE

IS PLUGGED INTO AN ELECTRICAL OUTLET. THESE

MOVING PARTS MAY BEGIN TO MOVE AT ANY TIME

THE STOVE IS PLUGGED IN.

THE VENT SURFACES CAN GET HOT ENOUGH TO

CAUSE BURNS IF TOUCHED. NONCOMBUSTIBLE

SHIELDING OR GUARDS MAY BE REQUIRED.

INSTALL VENT AT CLEARANCES SPECIFIED BY THE

VENT MANUFACTURER.

ALL VENTING JOINTS, WHETHER VERTICAL OR

HORIZONTAL, SHOULD BE MADE GASTIGHT

WITH RECOMMENDED SEALANTS SPECIFIED BY

VENT MANUFACTURER.

ACCORDING TO HUD HOUSING & URBAN

DEVELOPMENT REQUIREMENTS, WHEN

INSTALLED IN A MOBILE HOME, THIS STOVE MUST

BE GROUNDED DIRECTLY TO THE STEEL CHASSIS

OF THE MOBILE HOME AND BOLTED TO THE

FLOOR. DIRECT AIR ACCESS MUST BE PROVIDED,

USE A FRESH AIR KIT.

FOR USE IN THE UNITED STATES AND CANADA.

APPROVED FOR INSTALLATION IN MOBILE

HOMES.

CASTLE PELLET STOVES, PRODUCER OF THIS

APPLIANCE, RESERVES THE RIGHT TO ALTER ITS

PRODUCTS, SPECIFICATIONS AND/OR PRICE

WITHOUT NOTICE.

CAUTION CAUTION

Check for parts online at www.castlestoves.com or call 800-345-6007 M-F 8-5

6

Operator's Manual

Serenity Pellet Stove

TABLE OF CONTENTSTABLE OF CONTENTS

WARNINGS AND SAFETY PRECAUTIONS ........................................................................................................................................................................................2-5

Table of Contents .......................................................................................................................................................................................................................................6

REGISTRATION, SERVICE AND MAINTENANCE LOG .......................................................................................................................................................................7

INTRODUCTION...........................................................................................................................................................................................................................................8

Burning Pellet Fuel ..................................................................................................................................................................................................................................8

Automatic Safety Features ...................................................................................................................................................................................................................8

SPECIFICATIONS ..........................................................................................................................................................................................................................................9

UNPACKING .................................................................................................................................................................................................................................................9

INSTALLATION ...........................................................................................................................................................................................................................................10

Stove Placement ................................................................................................................................................................................................................................... 10

Floor Protection Requirements ....................................................................................................................................................................................................... 10

Clearance to Combustibles ...............................................................................................................................................................................................................11

Venting .....................................................................................................................................................................................................................................................12

Type of Vent ............................................................................................................................................................................................................................................12

Pellet Vent Installation ........................................................................................................................................................................................................................12

Preferred Pellet Vent Termination Clearances ......................................................................................................................................................................12-14

Outside Air Connection......................................................................................................................................................................................................................15

Mobile Home ......................................................................................................................................................................................................................................... 15

Venting Installation Examples ...................................................................................................................................................................................................16-21

UNDERSTANDING YOUR STOVE .........................................................................................................................................................................................................22

BECOMING FAMILIAR WITH YOUR CONTROLLER .........................................................................................................................................................................22

MAIN OPERATION CONTROLLER SCREEN DISPLAY ..................................................................................................................................................................... 23

COMPONENT STATUS SCREEN DISPLAY .......................................................................................................................................................................................24

PRE-OPERATION .......................................................................................................................................................................................................................................25

Mounting Your Controller .................................................................................................................................................................................................................25

Prior to Starting ............................................................................................................................................................................................................................... 25-26

OPERATION ................................................................................................................................................................................................................................................ 27

Start-up ....................................................................................................................................................................................................................................................27

Working in Dierent Operation Modes .................................................................................................................................................................................27-28

Setting Other Data On Your Controller ...................................................................................................................................................................................28-31

DIAGNOSTICS............................................................................................................................................................................................................................................31

SHUT DOWN PROCEDURE ....................................................................................................................................................................................................................31

MAINTENANCE ......................................................................................................................................................................................................................................... 32

Normal Care and Maintenance .......................................................................................................................................................................................................32

Daily Maintenance Tasks ....................................................................................................................................................................................................................33

Weekly, Monthly, and Bi-Monthly Tasks .................................................................................................................................................................................33-34

TROUBLESHOOTING AND REPAIR ......................................................................................................................................................................................................35

ORDERING REPLACEMENT PARTS ......................................................................................................................................................................................................35

TROUBLESHOOTING GUIDE ...........................................................................................................................................................................................................36-37

ILLUSTRATED PARTS BREAKDOWN .............................................................................................................................................................................................38-43

WIRING DIAGRAM ...................................................................................................................................................................................................................................44

EFFICIENCY ...............................................................................................................................................................................................................................................45

FIRE SAFETY ..............................................................................................................................................................................................................................................45

WARRANTY................................................................................................................................................................................................................................................46

7

Check for parts online at www.castlestoves.com or call 800-345-6007 M-F 8-5

Operator's Manual

Serenity Pellet Stove

ENGLISH

REGISTRATION, SERVICE AND MAINTENANCE LOG

Record the model number and serial number in the space provided for easy reference. Fill out and mail the registration card located

in the parts packet or register online at www.castlepelletstoves.com. Warranty is valid only if the completed registration is received by

Castle within 30 days of purchase.

OWNERSHIP RECORDS

Dealer’s Name:

Dealer’s Address:

City: State/Province: Zip Code/Postal Code:

Model Number: Serial Number:

Date of Purchase:

Notes:

SERVICE DATE SERVICE TECHNICIAN SERVICE DESCRIPTION

Check for parts online at www.castlestoves.com or call 800-345-6007 M-F 8-5

8

Operator's Manual

Serenity Pellet Stove

Clinkers

• Impurities, such as silica (clinkers), will need to be

regularly cleaned and removed from the pellet stove.

Clinkers will form a hard mass and block airow

through the pot liner. High quality fuels will result in

fewer clinkers.

Automatic Safety Features

Power Outage

During a power outage, the stove will shutdown safely. Do not

open the main door or ash door. During a power failure the

exhaust fan will not run. Keeping the doors sealed will allow the

exhaust vent to draft out naturally. When the power is restored,

the stove will not restart. If the exhaust temperature is still

120 degrees Fahrenheit when power is restored, the exhaust

and room fans will continue to run until the stove cools. See

“Operation” section for instructions on restarting the stove.

Overheating

Over Fire Protection: The stove features both electronic and

mechanical protection from over-ring and over-temp conditions.

To prevent damage to components, the stove will automatically

shut down if high limit switch thresholds are met. The exhaust

fan will continue to run until the proof of re switch cools. Allow

stove to cool before attempting to re-ignite. If the stove fails to

ignite and there are no pellets in the burn pot, it means that the

mechanical overtempt switch was also tripped and will need to

be manually re-set. See “Operation” section for more information.

INTRODUCTION

Congratulations on your investment in quality. Thank you for your

purchase on a Castle Pellet Stove. We have worked to ensure that

this pellet stove meets the highest standards for usability and

durability. With proper care, your stove will provide many years of

dependable service. Please read entire manual before installation

and use.

Burning Pellet Fuel

Ashes need to be removed from the stove periodically. See

“Normal Care and Maintenance” section for cleaning procedure.

Due to the nature of pellet fuels, this stove will require attention

periodically. Regular cleaning is an important part of burning

pellet fuel.

Pellets

• This pellet stove is designed and approved to burn

wood pellets, that comply with pellet fuels industry

standards. Minimum of 40 lbs. density per cubic feet,

1/4” to 5/16” in diameter, with a maximum length of

1-1/2”, and less than 1% ash.

• The performance of your pellet stove is greatly af-

fected by the type and quality of wood pellets. As the

heat output of various quality wood pellets dier, so

will the performance and heat output of the pellet

stove.

• Wood pellets are generally produced out of wood

waste such as sawdust and shavings. The raw material

is dried, mechanically fractioned to size and extruded

into pellets under high pressure. Wood pellets need

to be protected from direct exposure to water. Water

from sources such as condensation and humidity

causes pellets to expand and break down into unus-

able fuel. Keep fuel dry.

• It is important to select and use only pellets that

are dry and free from dirt and debris. Dirty fuel will

adversely aect the operation and performance of

the unit and will void the warranty. The Pellet Fuel

Institute (PFI) has established standards for wood

pellet manufacturers. Only use pellets that meet or

exceed PFI standards for premium fuel pellets. Pellets

that contain colored paper, cardboard, solvents, trash,

garbage, or other non-woody waste material should

be avoided.

Do Not Burn: Garbage; Lawn clippings or yard waste; materials

containing rubber, including tires; materials containing plastic;

waste petroleum products, paints or paint thinners, or asphalt

products; materials containing asbestos; construction or

demolition debris; railroad ties or pressure-treated wood; manure

or animal remains; paper products, cardboard, plywood, or

particleboard.

IF THE ELECTRICAL POWER FAILS ANY TIME WHEN THE

STOVE IS HOT, KEEP ALL STOVE DOORS CLOSED.

THE AUTOMATIC SAFETY FEATURES MUST NOT BE

BYPASSED.

WARNING

BURNING WOOD PELLETS ACCORDING TO

RECOMMENDATIONS WILL ASSURE LONGER STOVE LIFE

AND LESS FUEL RELATED PROBLEMS.

THE USE OF GRATES OR OTHER METHODS OF

SUPPORTING THE FUEL IN THIS STOVE IS PROHIBITED

AND WILL VOID ALL WARRANTIES.

CAUTION

9

Check for parts online at www.castlestoves.com or call 800-345-6007 M-F 8-5

Operator's Manual

Serenity Pellet Stove

ENGLISH

SPECIFICATIONS

Model Number Serenity 41728

Heating Capacity (1) 1,500 sq. ft.

Electrical Rating (2) 120 Volts, 60 Hz

Power Consumption 402 Watts ignition

77 Watts operating

Fuel Storage Capacity 40 lb

Flue Size (3) 3 in.

Width 18.25 in.

Height 34 in.

Depth 23.75 in.

Weight 186 lb

(1) Based on post 1982 home construction, requiring 35

BTU/Hr. per Sq. Ft. Heat output will vary, depending

on the brand, type and quality of fuel and the moisture

content. Consult your dealer for best results.

(2) Install per NFPA 70 and follow all state and local codes,

contact licensed electrical contractor for assistance.

(3) Install per NFPA 211 and follow all state and local codes,

contact licensed installers for assistance.

Listing label:

Tested to the following standards: ASTM E1509, ULC S627, and

ASTM E2779, ASTM E2515, and CSA B415.1

Glass Specications:

This stove is equipped with 5 mm ceramic glass. Replace glass

only with Castle Pellet Stoves ceramic glass. Call your servicing

dealer or Castle at 1-800-345-6007 for replacement parts.

COMPLIANCE NOTE

The Serenity pellet heater, by Castle, meets the U.S. Environmental

Protection Agency’s emission limits for pellet heaters sold after

May 15, 2020.

This wood heater needs periodic inspection and repair for proper

operation. It is against federal regulations to operate this wood

heater in a manner inconsistent with operating instructions in this

manual. This wood heater has a manufacturer-set minimum low

burn rate that must not be altered. It is against federal regulations

to alter this setting or otherwise operate this wood heater in a

manner inconsistent with operating instructions in this manual.

UNPACKING

Your Castle Serenity will come partially assembled. Remove all

packing material and tape from the inside of the rebox. Remove

any tape on the outside of the glass. Open the hopper, remove

all packing material, parts bag, manual bag, repot, controller

assembly, and power cord. A parts bag containing one (1) remote

control, one (1) spare fuse, one (1) 13 mm wrench, one (1) 4 mm

hex wrench, and four (4) adjustable feet are included for your

convenience.

1. Using the 13 mm wrench, remove the four (4) bolts from the

bottom of the pallet that secure the stove to the pallet.

2. Install the four (4) adjustable feet to the bottom of the stove.

3. Open the door and install the repot as shown on page 32 of

the operator’s manual.

4. Using the 4 mm hex wrench, install the controller assembly

according to the instructions on page 22 of the operator’s

manual.

THIS INSTALLATION MUST CONFORM WITH LOCAL

CODES. IN THE ABSENCE OF LOCAL CODES YOU

MUST COMPLY WITH ASTM E1509, ASTM E2779,

ASTM E2515, CSA B415.1, AND ULC S627.

CASTLE PELLET STOVES, MANUFACTURER OF

THIS APPLIANCE, RESERVES THE RIGHT TO ALTER

ITS PRODUCTS AND/OR THEIR SPECIFICATIONS

WITHOUT NOTICE.

MAKE SURE THE HOPPER IS FREE OF ALL FOREIGN

MATTER BEFORE FILLING WITH FUEL. FOREIGN

MATERIAL WILL CAUSE AUGER JAMS AND WILL

VOID STOVE WARRANTY.

CAUTION

Check for parts online at www.castlestoves.com or call 800-345-6007 M-F 8-5

10

Operator's Manual

Serenity Pellet Stove

INSTALLATION

It is recommended the stove be installed and serviced by

authorized professionals who are certied by the National

Fireplace Institute (NFI) as NFI Pellet Specialists.

Proper installation of this stove is necessary for safe and ecient

operation. Installing this product improperly may result in a house

re and personal injury. All applicable building codes for your

location must be followed. In areas where building codes require

additional steps to the installation of this product not included

in this manual, the building codes will take precedent and must

be followed. Contact your local building inspector to obtain any

necessary permits or inspection guidelines before installing the

product.

Stove Placement

Sketch out a plan for installing the stove including dimensions

before permanent placement. When determining the location for

the stove, wall stud location is critical. You may need to adjust the

location of the stove to avoid trying to vent through a wall stud.

Before placing the pellet stove, connect the vent and allow for

minimum clearance to combustible walls.

Floor Protection Requirements

The stove must be installed on a noncombustible oor, with

proper oor protection, or on a masonry hearth. When a clean

out t-vent is installed in the inside of a home, the oor protector

must extend 2” beyond rear of t-vent. SEE FIGURE 1. When stove

is vented straight through the wall and the clean out t-vent is on

the exterior of the home, the minimum clearance is 2” from the

back of the stove to the wall. SEE FIGURE 2. The minimum oor

protector material is 24 GA sheet metal.

Figures 1 And 2: Pellet Stove Floor Pad Clearances

THIS STOVE SHOULD NOT BE USED AS THE

ONLY SOURCE OF HEAT IN THE HOUSE. POWER

OUTAGES AND PERIODIC MAINTENANCE WILL

RESULT IN A TOTAL LOSS OF HEAT.

CONTACT LOCAL BUILDING OR FIRE OFFICIALS

ABOUT RESTRICTIONS AND INSTALLATION

INSPECTION REQUIREMENTS IN YOUR AREA.

CONTACT YOUR LOCAL AUTHORITY SUCH

AS MUNICIPAL BUILDING DEPARTMENT, FIRE

DEPARTMENT, FIRE PREVENTION BUREAU, ETC.

TO DETERMINE THE NEED FOR A PERMIT.

KEEP COMBUSTIBLE MATERIALS SUCH AS GRASS,

LEAVES, ETC. AT LEAST 3 FEET AWAY FROM THE

FLUE OUTLET ON THE OUTSIDE OF THE BUILDING.

INSTALLATION AND REPAIR OF THIS PELLET STOVE

SHOULD BE DONE BY A QUALIFIED SERVICE

PERSON. THE APPLIANCE SHOULD BE INSPECTED

BEFORE USE AND AT LEAST ANNUALLY BY A

QUALIFIED SERVICE PERSON. IT IS IMPERATIVE

THAT CONTROL COMPARTMENTS, FIRE BOX, AND

CIRCULATING AIR PASSAGEWAYS OF THE STOVE BE

KEPT CLEAN.

CAUTION

READ THIS ENTIRE MANUAL BEFORE YOU INSTALL

AND USE THIS STOVE. FAILURE TO FOLLOW

THE INSTRUCTIONS MAY RESULT IN PROPERTY

DAMAGE, BODILY INJURY, OR EVEN DEATH.

DO NOT INSTALL A FLUE DAMPER IN THE EXHAUST

VENTING SYSTEM OF THIS UNIT.

DO NOT CONNECT THIS UNIT TO A CHIMNEY FLUE

SERVING ANOTHER APPLIANCE.

CHILDREN AND ADULTS SHOULD BE ALERTED TO

THE HAZARDS OF HIGH SURFACE TEMPERATURES

AND SHOULD STAY AWAY TO AVOID BUMPS TO

SKIN AND/OR CLOTHING.

YOUNG CHILDREN SHOULD BE CAREFULLY

SUPERVISED WHEN THEY ARE IN THE SAME ROOM

AS THE STOVE.

CLOTHING AND OTHER FLAMMABLE MATERIALS

SHOULD NOT BE PLACED ON OR NEAR THIS UNIT.

2"

6"

2"

6"

WARNING

11

Check for parts online at www.castlestoves.com or call 800-345-6007 M-F 8-5

Operator's Manual

Serenity Pellet Stove

ENGLISH

Clearances To Combustibles

NOTE: These are minimum clearances to combustible walls established by the ASTM testing lab. (SEE FIGURES 3, 4, 5, & 6.)

NOTE: When interior vent is installed vertically, the clearance to the back wall is determined by the vent size used. Install

vent at clearance specied by the vent manufacturer. Take into consideration any upward turning elbows or tees.

5"

7"

Figure 3: Straight Installation Through Wall Figure 4: Corner Installation Through The Wall Vents

Figure 5: Straight Installation Interior Vertical Vents Figure 6: Corner Installation Interior Vertical Vents

5"

2"

7"

5"

2"

Check for parts online at www.castlestoves.com or call 800-345-6007 M-F 8-5

12

Operator's Manual

Serenity Pellet Stove

Venting

Before venting, consult vent manufacturer’s specications and

recommendations for all venting installations.

The following installation guidelines must be followed to ensure

conformity with both the safety listing of this stove and to local

building codes.

Note: Where passage through a wall, or partition

of combustible construction is desired, the

installation shall conform to CAN/CSA -8365.

Type Of Vent

The pellet venting pipe (also known as L vent) is constructed of

two layers with air space between the layers. This air space acts as

an insulator and reduces outside surface temperature of pipe to

allow a clearance to combustibles.

A UL listed 3” or 4” type L pellet vent exhaust system must be used

for installation and attached to the pipe connector provided on

the back of the stove. Use a 3” to 4” adapter for 4” pipe. A cap must

be used at the termination of type L vent chimneys. For elevations

above 2,500 feet above sea level, a 4” L is required.

Pellet Stove Vent Installation

Vent termination MUST exhaust above air inlet elevation.

It is required to install at least three feet (3’) of vertical pellet vent

pipe. This vertical pipe will create some natural draft to prevent

the possibility of smoke or odor during appliance shutdown

and will keep exhaust from causing a nuisance or hazard from

exposure to high temperatures.

The installation must include a clean out tee to enable collection

of y ash and to permit periodic cleaning of the exhaust system.

Total length of horizontal vent must not exceed 10 feet. The

maximum recommended vertical venting height is 18 feet.

All joints for pellet vent are required to be fastened with at least

three screws and all pellet vent connections

(including adapters, elbows, etc.) should be sealed

airtight by injecting 500° F. RTV silicone into the

gap between sections.

The area where the vent pipe goes through to the

exterior of the home must be sealed with silicone

or other means to maintain the vapor barrier

between the exterior and the interior of the home.

500º F

RTV

Silicon

DO NOT CONNECT THIS UNIT TO A CHIMNEY FLUE

SERVING ANOTHER APPLIANCE.

DO NOT INSTALL A FLUE DAMPER IN THE EXHAUST

VENTING SYSTEM OF THIS UNIT.

DO NOT CONNECT DIRECTLY TO A MASONRY

CHIMNEY.

DO NOT TERMINATE VENT IN ANY ENCLOSED

OR SEMIENCLOSED AREA, SUCH AS; CARPORTS,

GARAGE, ATTIC, CRAWL SPACE, UNDER A SUN

DECK OR PORCH, NARROW WALKWAY OR CLOSED

AREA, OR ANY LOCATION THAT CAN BUILD

UP A CONCENTRATION OF FUMES SUCH AS A

STAIRWELL, COVERED BREEZEWAY ETC.

CAUTION

VENT SURFACES CAN GET HOT ENOUGH TO

CAUSE BURNS IF TOUCHED. NONCOMBUSTIBLE

SHIELDING OR GUARDS MAY BE REQUIRED.

PELLET VENT MUST MAINTAIN MINIMUM

CLEARANCES SPECIFIED BY VENT MANUFACTURER

FOR CLEARANCE TO ANY COMBUSTIBLES.

INSTALL VENT AT CLEARANCES SPECIFIED BY THE

VENT MANUFACTURER.

ALL VENTING, WHETHER VERTICAL OR

HORIZONTAL, JOINTS SHOULD BE MADE GAS

TIGHT WITH RECOMMENDED SEALANTS.

WARNING

13

Check for parts online at www.castlestoves.com or call 800-345-6007 M-F 8-5

Operator's Manual

Serenity Pellet Stove

ENGLISH

Preferred Pellet Vent Termination Clearances

• The stove vent must terminate on the outside of the building. Horizontal terminations must extend a minimum

of 12” from the wall. Vertical terminations must protrude a minimum 24” from the roof surface. In addition, all

clearances listed below must be met. SEE FIGURE 7.

• Must have an approved cap (to prevent water from entering) or a 45° downturn with rodent screen.

• If the termination is located on a windy side of the house, we suggest using an approved house shield to prevent

soot from building up on the side of the house.

• A vent must not be located where it will become plugged by snow or other material.

A: A Minimum 4’ clearance below or beside any door or

window that opens. (This clearance may be reduced

to 18” if using outside air). We recommend the door or

window be kept closed during operation. Minimum 1’

clearance below or beside any window that does not

open.

B: Minimum 1’ clearance above any door or window that

opens.

C: Minimum 2’ clearance from any adjacent building.

D: Minimum 7’ clearance above any grade when adjacent to

public walkways.

NOTE: Vent may not terminate in covered walkway or

breezeway.

E: Minimum 2’ clearance above any grass, plants, or other

X

H

F

E

F

A

G

D

B

A

H

C

combustible materials.

F: Minimum 3’ clearance from any forced air intake of any

other appliance.

G: Minimum 2’ clearance below eaves or overhangs.

H: Minimum 1’ clearance horizontally from combustible wall.

X: Must be a minimum of 2’ above the roof.

Figure 7: Vent Termination

Check for parts online at www.castlestoves.com or call 800-345-6007 M-F 8-5

14

Operator's Manual

Serenity Pellet Stove

The vent must have a support bracket every 5’ of pellet vent when

on the exterior of the structure.

The vent height and run must not exceed the distance as

illustrated in the diagram below.

Venting into this (the lighter) shaded area may require

combustion motor voltage adjustments and/or inlet air

adjustments (intake). SEE FIGURE 9.

Venting The Pellet Stove (See Figures 8 through 16.)

33 Feet

(max.)

30 Feet

25 Feet

20 Feet

15 Feet

10 Feet

5 Feet

0 Feet

5 Feet

10 Feet

(max.)

Figure 8: Intake and Exhaust Positions

Figure 9: Venting and Combustion Motor Voltage Adjustment Chart

MAKE SURE PELLET STOVE IS VENTED CORRECTLY.

DO NOT INSTALL FLUE DAMPER IN THE EXHAUST

VENTING SYSTEM OF THIS UNIT.

USE AN APPROVED WALL THIMBLE WHEN PASSING

THE VENT THROUGH WALLS. USE A CEILING

SUPPORT/FIRE STOP SPACER WHEN PASSING THE

VENT THROUGH CEILINGS MAKE SURE TO MAINTAIN

CLEARANCE TO ANY COMBUSTIBLES.

IF USING MORE THAN ONE TEE AND 180O OF ELBOWS,

YOU MUST USE 4“ VENTING PIPES.

CAUTION

8”

4”

2” DIA

9 3/4”

4 1/4”

3” DIA

NOTE: THE ADJUSTABLE FOOT PAD CAN ADD UP TO

1 INCH TO HEIGHT MEASUREMENTS DEPENDING

ON YOUR INSTALLATION LEVELING REQUIREMENTS.

THIS DIMENSION MUST BE ADDED TO THE HEIGHT

FOR PROPER INSTALLATION OF VENT PIPES.

15

Check for parts online at www.castlestoves.com or call 800-345-6007 M-F 8-5

Operator's Manual

Serenity Pellet Stove

ENGLISH

Outside Air Connection

Connection from the intake pipe (2” diameter pipe in rear of stove,

See Figure 8) to the outside of the house is REQUIRED for mobile

home installation. It is recommended in tightly sealed homes

with exhaust fans such as kitchen or bathroom fans. This will

eliminate poor performance due to negative pressure.

Only noncombustible pipe 2” (or greater) in diameter is approved

to use for outside air connections (straight or exible).

NOTE: PVC pipe is NOT approved and should NEVER be

connected to the stove.

HINT: A Castle Pellet Stove air inlet will accept

automotive exhaust pipes and couplers

If the air inlet is connected to the outside, it MUST be terminated

with a vertical 90º bend (down) or with a wind hood. Failure to do

so could result in a burn back during high winds blowing directly

up the air inlet during a simultaneous power failure.

Blockage, excessive length, or extra bends in the air intake pipe

will starve the stove of combustion air. A 90º bend is equivalent in

restriction to approximately 30” of straight inlet pipe.

Mobile Home

Installation in a mobile home should be in accordance with the

manufactured home and safety standard. Department of Housing

and Urban Development (HUD) CITE: 24CFR3280.707 stating

this stove must be vented to the outside. In addition to the

standard installation instructions, the following requirements are

mandatory for installation in a mobile home:

1. The stove must be permanently attached to the oor.

2. Stove must have an outside air source.

3. Stove must be electrically grounded to the steel chassis

of the mobile home.

4. All vertical chimney vents must have wall supports.

5. All exhaust systems must have a spark arrestor.

6. Check with local building ocials to see if other codes

may apply.

CARBON MONOXIDE POISONING HAZARD. DO

NOT CONNECT TO ANY AIR DISTRIBUTION DUCT

OR SYSTEM. DO NOT INSTALL IN A SLEEPING

ROOM.

WARNING

THE OPERATION OF EXHAUST FANS SUCH AS

BATHROOM FANS, ATTIC FANS, ETC. MIGHT

STARVE THE PELLET STOVE OF COMBUSTIBLE AIR

CREATING A NEGATIVE PRESSURE IN THE ROOM.

PROVIDE ADEQUATE VENTILATION IN THE ROOM

ACCOMPANYING THE PELLET STOVE. IF NOT, THE

PRESSURE SWITCH MAY SHUT OFF OPERATION

OF THE PELLET STOVE.

THE STRUCTURAL INTEGRITY OF THE

MANUFACTURED HOME FLOOR, WALL, AND

CEILING/ROOF MUST BE MAINTAINED.

CAUTION

Check for parts online at www.castlestoves.com or call 800-345-6007 M-F 8-5

16

Operator's Manual

Serenity Pellet Stove

Figure 11: Straight Installation—Inside Vertical Rise, Horizontal Termination

oor

wall

venting pipe

fresh air inlet

heat-resistant material

Figure 10: Straight Installation—Outside Vertical Rise, Horizontal Termination

oor

termination

wall

fresh air inlet

tee

clean-out

heat-resistant material

termination

SIMPLE STOVE VENTILATION EXAMPLES

tee

clean-out

17

Check for parts online at www.castlestoves.com or call 800-345-6007 M-F 8-5

Operator's Manual

Serenity Pellet Stove

ENGLISH

3” Min.

Outside air may be drawn from

a vented crawl space.

Floor

Protection

“L” Vent

Ceiling Support/Fire Stop Spacer Vent must

maintain

clearance to

combustibles

Insulation

must maintain

clearance

Vertical Cap

Storm Collar

Roof Flashing

24” Minimum

* Install a vent at clearance specied by the vent manufacturer

Vent

Clearance*

COMPLEX STOVE VENTILATION EXAMPLES

Figure 12: Interior Vertical Installation

Check for parts online at www.castlestoves.com or call 800-345-6007 M-F 8-5

18

Operator's Manual

Serenity Pellet Stove

Vent

Clearance*

3” Min.

Outside air may be drawn from

a vented crawl space.

Floor

Protection

“L” Vent

Class A Chimney Ceiling Support

Class A chimney must

maintain clearances outlined

in the chimney’s installation

instructions (usually 2”)

Storm Collar

Roof Flashing

“L” Vent to Class A Chimney Adapter

Class A Chimney

* Install a vent at clearance specied by the vent manufacturer

CLASS A CHIMNEY RETROFIT

Figure 13: Class A Chimney Retrot

19

Check for parts online at www.castlestoves.com or call 800-345-6007 M-F 8-5

Operator's Manual

Serenity Pellet Stove

ENGLISH

Silicone

Vertical Cap

Storm Collar

Cover Plate (non-combustible)

“L” Vent

Seal the cover

plate with silicone

“L” Vent Flex

Section

Lintel

Outside air may be drawn

from the ash cleanout.

NOTE: you will probably need a short horizontal section here to

clear the lintel and allow the hopper lid to open

6” Min.

3”

MASONRY FIREPLACE HEARTH STOVE

Figure 14: Masonry Fireplace Hearth Stove

Check for parts online at www.castlestoves.com or call 800-345-6007 M-F 8-5

20

Operator's Manual

Serenity Pellet Stove

6” Min.

3”

Vertical Cap

Storm Collar

Cover Plate (non-combustible)

“L” Vent

Seal the cover

plate with silicone

Silicone

“L” Vent Flex

Section

ZEROCLEARANCE METAL FIREPLACE HEARTH STOVE

Figure 15: Zero-Clearance (Metal) Fireplace Hearth Stove

La page charge ...

Castle Pellet Stoves 41278 CASTLE SERENITY 2.0 Le manuel du propriétaire

Castle Pellet Stoves 41278 CASTLE SERENITY 2.0 Le manuel du propriétaire

Autres documents