LS
6381
6381-2
6381-3
6381-4
6381-5
LS
6382
6382-2
6382-3
6382-4
6382-5
VS
324
324-2
324-3
324-4
324-5
User’s manual
Scan the QR code to go and
subscribe our tutorial channel
Congratulations
on purchasing your new VTech product. Before
using this telephone, please read Important safety
instructions.
This manual has all the feature operations and
troubleshooting necessary to install and operate your
new VTech telephone. Please review this manual
thoroughly to ensure proper installation and operation
of this innovative and feature rich VTech product.
For support, shopping, and everything new at
VTech, visit our website at www.vtechphones.com. In
Canada, please visit phones.vtechcanada.com.
T
Compatible with
Hearing Aid T-Coil
TIA-1083
Telephones identified
with this logo have
reduced noise and
interference when
used with most T-coil
equipped hearing aids
and cochlear implants.
The TIA-1083 Compliant
Logo is a trademark of
the Telecommunications
Industry Association.
Used under license.
The ENERGY STAR®
program (www.
energystar.gov)
recognizes and
encourages the use
of products that save
energy and help protect
our environment. We
are proud to mark
this product with the
ENERGY STAR® label
indicating it meets the
latest energy efficiency
guidelines.
Important safety instructions
When using your telephone equipment, basic safety
precautions should always be followed to reduce the
risk of fire, electric shock and injury, including the
following:
1. Read and understand all instructions.
2. Follow all warnings and instructions marked on
the product.
3. Unplug this product from the wall outlet before
cleaning. Do not use liquid or aerosol cleaners.
Use a damp cloth for cleaning.
4. CAUTION: Do not install the telephone base at a
height above 2 meters.
5. Do not use this product near water such as near a
bath tub, wash bowl, kitchen sink, laundry tub or a
swimming pool, or in a wet basement or shower.
6. Do not place this product on an unstable table,
shelf, stand or other unstable surfaces.
7. Avoid placing the telephone system in places
with extreme temperature, direct sunlight, or
other electrical devices. Protect your phone from
moisture, dust, corrosive liquids and fumes.
8. Slots and openings in the back or bottom of the
telephone base and handset are provided for
ventilation. To protect them from overheating,
these openings must not be blocked by placing
the product on a soft surface such as a bed, sofa
or rug. This product should never be placed near
or over a radiator or heat register. This product
should not be placed in any area where proper
ventilation is not provided.
9. This product should be operated only from the
type of power source indicated on the marking
label. If you are not sure of the type of power
supply in your home or office, consult your dealer
or local power company.
10. Do not allow anything to rest on the power cord.
Do not install this product where the cord may be
walked on.
11. Never push objects of any kind into this product
through the slots in the telephone base or handset
because they may touch dangerous voltage
points or create a short circuit. Never spill liquid of
any kind on the product.
12. To reduce the risk of electric shock, do not
disassemble this product, but take it to an
authorized service facility. Opening or removing
parts of the telephone base or handset other
than specified access doors may expose you
to dangerous voltages or other risks. Incorrect
reassembling can cause electric shock when the
product is subsequently used.
13. Do not overload wall outlets and extension cords.
14. Unplug this product from the wall outlet and refer
servicing to an authorized service facility under
the following conditions:
• When the power supply cord or plug is
damaged or frayed.
• If liquid has been spilled onto the product.
• If the product has been exposed to rain or
water.
• If the product does not operate normally by
following the operating instructions. Adjust
only those controls that are covered by the
operation instructions. Improper adjustment
of other controls may result in damage and
often requires extensive work by an authorized
technician to restore the product to normal
operation.
• If the product has been dropped and the
telephone base and/or handset has been
damaged.
• If the product exhibits a distinct change in
performance.
15. Avoid using a telephone (other than cordless)
during an electrical storm. There is a remote risk
of electric shock from lightning.
16. Do not use the telephone to report a gas leak in the
vicinity of the leak. Under certain circumstances,
a spark may be created when the adapter is
plugged into the power outlet, or when the
handset is replaced in its cradle. This is a common
event associated with the closing of any electrical
circuit. The user should not plug the phone into
a power outlet, and should not put a charged
handset into the cradle, if the phone is located
in an environment containing concentrations of
flammable or flame-supporting gases, unless
there is adequate ventilation. A spark in such an
environment could create a fire or explosion.
Such environments might include: medical use of
oxygen without adequate ventilation; industrial
gases (cleaning solvents; gasoline vapors; etc.); a
leak of natural gas; etc.
17. Only put the handset of your telephone next to
your ear when it is in normal talk mode.
18. The power adapter is intended to be correctly
oriented in a vertical or floor mount position. The
prongs are not designed to hold the plug in place
if it is plugged into a ceiling, under-the-table or
cabinet outlet.
19. For pluggable equipment, the socket outlet shall
be installed near the equipment and shall be
easily accessible.
20. CAUTION: Use only the batteries
indicated in this manual. There may be a risk of
explosion if a wrong type of battery is used for
the handset. Use only the supplied rechargeable
batteries or replacement batteries (BT162342/
BT262342) for the handset. Do not dispose of
batteries in a fire. They may explode.
• Do not use the battery in following conditions:
» High or low extreme temperature during use,
storage or transportation.
» Replacement of a battery with an incorrect type
that can defeat a safeguard.
» Disposal of a battery into fire or a hot oven, or
mechanically crushing or cutting of a battery,
that can result in an explosion.
» Leaving a batteryin an extremely high
temperature surrounding environment that
can result in an explosion or the leakage of
flammable liquid or gas.
» A battery subjected to extremely low air
pressure that can result in an explosion or the
leakage of flammable liquid or gas.
21. Use only the adapter included with this product.
Incorrect adapter polarity or voltage can seriously
damage the product.
22. The applied nameplate is located at the bottom or
near of the product.
SAVE THESE INSTRUCTIONS
Battery
• Use only the batteries provided or equivalent.
To order a replacement, visit our website at
www.vtechphones.com or call 1 (800) 595-9511.
In Canada, go to phones.vtechcanada.com or call
1 (800) 267-7377.
• Do not dispose of the battery in a fire. Check
with local waste management codes for special
disposal instructions.
• Do not open or mutilate the battery. Released
electrolyte is corrosive and may cause burns or
injury to the eyes or skin. The electrolyte may be
toxic if swallowed.
• Exercise care in handling batteries in order not to
create a short circuit with conductive materials.
• Charge the battery provided with this product
only in accordance with the instructions and
limitations specified in this manual.
Precautions for users of implanted cardiac
pacemakers
Cardiac pacemakers (applies only to digital cordless
telephones):
Wireless Technology Research, LLC (WTR), an
independent research entity, led a multidisciplinary
evaluation of the interference between portable
wireless telephones and implanted cardiac
pacemakers. Supported by the U.S. Food and Drug
Administration, WTR recommends to physicians that:
Pacemaker patients
• Should keep wireless telephones at least six inches
from the pacemaker.
• Should NOT place wireless telephones directly over
the pacemaker, such as in a breast pocket, when it is
turned ON.
• Should use the wireless telephone at the ear opposite
the pacemaker.
WTR’s evaluation did not identify any risk to bystanders
with pacemakers from other persons using wireless
telephones.
About cordless telephones
• Privacy: The same features that make a cordless
telephone convenient create some limitations.
Telephone calls are transmitted between the
telephone base and the cordless handset by radio
waves, so there is a possibility that the cordless
telephone conversations could be intercepted
by radio receiving equipment within range of
the cordless handset. For this reason, you should
not think of cordless telephone conversations as
being as private as those on corded telephones.
• Electrical power: The telephone base of this
cordless telephone must be connected to a
working electrical outlet. The electrical outlet
should not be controlled by a wall switch. Calls
cannot be made from the cordless handset if the
telephone base is unplugged, switched off or if
the electrical power is interrupted.
• Potential TV interference: Some cordless
telephones operate at frequencies that may cause
interference to televisions and VCRs. To minimize
or prevent such interference, do not place
the telephone base of the cordless telephone
near or on top of a TV or VCR. If interference is
experienced, moving the cordless telephone
farther away from the TV or VCR often reduces or
eliminates the interference.
• Rechargeable batteries: Exercise care in handling
batteries in order not to create a short circuit with
conducting material such as rings, bracelets and
keys. The battery or conductor may overheat and
cause harm. Observe proper polarity between
the battery and the battery charger.
• Nickel-metal hydride rechargeable batteries:
Dispose of these batteries in a safe manner. Do not
burn or puncture the battery. Like other batteries
of this type, if burned or punctured, they could
release caustic material which could cause injury.
ECO mode
This power conserving technology reduces power
consumption for optimal battery performance. The
ECO mode activities automatically whenever the
handset is synchronized with the telephone base.
For C-UL compliance only
Mesures de sécurité importantes
Afin de réduire les risques d’incendie, de blessures
corporelles ou d’électrocution, suivez toujours ces
mesures préventives de base lorsque vous utilisez
votre téléphone :
1. Lisez et comprenez bien toutes les instructions.
2. Observez toutes les instructions et mises en garde
inscrites sur l’appareil.
3. Débranchez ce téléphone de la prise murale
avant de le nettoyer. N’utilisez pas de nettoyeurs
liquides ni en aérosol. N’utilisez qu’un chiffon
doux et légèrement humecté.
4. ATTENTION: Ne pas installer le socle téléphonique
à une hauteur supérieure à 2 mètres.
5. N’utilisez pas ce produit près de l’eau, tel que près
d’un bain, d’un lavabo, d’un évier de cuisine, d’un
bac de lavage ou d’une piscine, ou dans un sous-
sol humide ou sous la douche.
6. Ne déposez pas ce téléphone sur un chariot,
support ou table chancelants. L’appareil pourrait
tomber et être sérieusement endommagé.
7. Évitez d’installer le système téléphonique dans
les endroits soumis à une température extrême,
à la lumière directe du soleil ou à proximité
immédiate d’autres appareils électriques ou
électroniques. Protégez votre téléphone contre
les sources d’humidité, la poussière, les vapeurs
et les liquides corrosifs.
8. Le boîtier de l’appareil est doté de fentes et
d’ouvertures d’aération situées à l’arrière ou
en dessous. Afin d’empêcher la surchauffe, ces
ouvertures ne doivent pas être obstruées en
plaçant l’appareil sur un lit, divan, tapis ou autre
surface similaires. Ne placez pas cet appareil
proximité d’un élément de chauffage ni d’une
plinthe électrique. De plus, ne l’installez pas dans
une unité murale ou un cabinet fermé qui ne
possède pas d’aération adéquate.
9. Ne faites fonctionner cet appareil qu’avec le
type d’alimentation indiqué sur les étiquettes de
l’appareil. Si vous ne connaissez pas le voltage de
votre maison, consultez votre marchand ou votre
fournisseur d’électricité.
10. Ne déposez rien sur le cordon d’alimentation.
Installez cet appareil dans un endroit sécuritaire,
là où personne ne pourra trébucher sur la
ligne d’alimentation ni le cordon téléphonique
modulaire.
11. N’insérez jamais d’objets à travers les fentes et
ouvertures de cet appareil, car ils pourraient
toucher à des points de tension dangereux ou
court-circuiter des pièces, ce qui constituerait un
risque d’incendie ou d’électrocution. N’échappez
pas de liquides dans l’appareil.
12. Afin de réduire les risques d’électrocution, ne
démontez pas l’appareil, mais apportez-le plutôt
à un centre de service qualifié s’il doit être réparé.
En enlevant le couvercle, vous vous exposez à
des tensions dangereuses ou autres dangers
similaires. Un remontage inadéquat peut être à
l’origine d’une électrocution lors d’une utilisation
ultérieure de l’appareil. Débranchez l’appareil
avant de procéder au nettoyage. Utilisez un
chiffon humide et doux.
13. Ne surchargez pas les prises de courant et les
rallonges.
14. Débranchez cet appareil de la prise de courant et
communiquez avec le département de service à
la clientèle de VTech dans les cas suivants:
• Lorsque le cordon d’alimentation est
endommagé ou écorché.
• Si du liquide a été échappé dans l’appareil.
• Si l’appareil a été exposé une source
d’humidité telle que la pluie ou l’eau.
• Si le produit ne fonctionne pas normalement
en respectant les instructions de
fonctionnement. Réglez uniquement les
commandes indiquées dans le les instructions
de fonctionnement. Les réglages incorrects
des autres commandes pourraient provoquer
un dommage qui pourrait exiger un travail
exhaustif de la part d’un technicien autorisé
afin de rétablir le fonctionnement normal de
l’appareil.
• Si le produit a été échappé et que le socle et/
ou le combiné a été endommagé.
• Si le produit affiche une nette diminution de
sa performance.
15. Évitez d’utiliser un téléphone (autre qu’un sans
fil) pendant un orage. Les éclairs peuvent être à
l’origine d’une électrocution.
16. N’utilisez pas le téléphone pour rapporter une
fuite de gaz à proximité de la fuite. En certaines
circonstances, une flammèche pourrait être
provoquée lorsque l’adaptateur est branché à une
prise de courant, ou lorsque le combiné est déposé
sur le socle. Ceci est un événement commun
associé à la fermeture d’un circuit électrique.
L’utilisateur ne devrait pas brancher le téléphone
à une prise de courant, et ne devrait pas déposer
le combiné chargé sur le socle, si le téléphone se
trouve à proximité d’un endroit comportant des
concentrations de gaz inflammables, moins que
la ventilation soit adéquate. Une flammèche dans
un tel endroit pourrait provoquer un incendie ou
une explosion. De tels environnements peuvent
comprendre: des endroits où l’on utilise de
l’oxygène médical sans ventilation adéquate; des
gaz industriels (dissolvants de nettoyage, des
vapeurs d’essence, etc.); une fuite de gaz naturel,
etc.
17. Ne placez que le combiné de votre téléphone près
de votre oreille lorsqu’en mode de conversation.
18. Ces adaptateurs ont été conçus pour être orientés
en position verticale ou montés au sol. Les broches
ne sont pas conçues pour maintenir l’adaptateur
en place si celui-ci est barnché dans une prise au
plafond ou sous une table/ armoire.
19. Pour le MATERIEL RACCORDE PAR PRISE DE
COURANT, le socle de prise de courant doit
etre installe a proximite du materiel et doit etre
aisement accessible.
MISE EN GARDE: Il peut y avoir un risque
d’explosion si vous utilisez le mauvais type de
piles pour le téléphone. N’utilisez que les piles
rechargeable inclus ou les piles de rechange
(BT162342/BT262342). N’incinérez pas les piles.
Celles-ci risqueraient d’exploser.
• Évite d’utiliser la batterie dans les conditions
suivantes:
» des températures extrêmes faibles ou élevées
auxquelles une batterie peut être soumise
pendant l’utilisation, le stockage ou le transport;
» Remplacement d’une batterie par un type
incorrect pouvant supprimer une protection;
» mise au rebut d’une batterie dans un feu ou
dans un four chaud, ou écrasement mécanique
ou coupure d’une batterie, susceptible de
provoquer une explosion;
» maintien d’une batterie dans un environnement
à très haute température pouvant provoquer
une explosion ou la fuite de liquide ou de gaz
inflammables;
» batterie soumise à une pression de l’air
extrêmement faible pouvant provoquer une
explosion ou la fuite de liquide ou de gaz
inflammables.
21. N’utilisez que les adaptateurs inclus avec ce
produit. L’utilisation d’un adaptateur dont la
polarité ou la tension serait inadéquate risque
d’endommager sérieusement le produit et mettre
votre sécurité en péril.
La plaque signal tique appliqu e est situ e au bas ou
proximit du produit.
CONSERVEZ CES INSTRUCTIONS
Pile
• N’utilisez que la pile incluse ou l’ quivalent.
Pour commander une pile de recharge, visitez
notre site Web au www.vtechphones.com ou
composez le 800-595-9511. Au Canada, visitez le
phones.vtechcanada.com ou composez le 800-
267-7377.
• Ne jetez pas la pile au feu. Vérifiez les instructions
spécifiques de mise aux rebus auprès des autorités
locales.
• N’ouvrez pas et ne mutilez pas la pile. L’électrolyte
qui s’en échapperait est corrosif et pourrait causer
des brûlures ou des blessures aux yeux ou à la
peau. L’électrolyte est toxique si avalé.
• Soyez prudents lorsque vous manipulez les piles
afin d’éviter les courts-circuits provoqués par des
matériaux conducteurs.
• Rechargez la pile incluse avec cet appareil, selon
les instructions et limites spécifiées dans ce guide
d’utilisation.
Stimulateurs cardiaques implantés dans
l’organisme
Les simulateurs cardiaques (s’applique uniquement
aux téléphones numériques sans fil):
L’organisme ‘Wireless Technology Research, LLC
(WTR)’, une firme de recherche indépendante, a mené
une évaluation pluridisciplinaire des interférences
entre les téléphones sans fil portatifs et les stimulateurs
cardiaques implantés dans l’organisme. Appuyée par
l’Administration des aliments et drogues (FDA) des
États-Unis, la firme WTR recommande aux médecins:
Avis aux détenteurs de stimulateurs
cardiaques
• Ils doivent tenir le téléphone sans fil à une distance
d’au moins six pouces du stimulateur cardiaque.
• Ils ne doivent PAS placer le téléphone sans fil
directement sur le stimulateur cardiaque, tel que
dans une poche de chemise, lorsque celui-ci est
en marche.
• Ils doivent utiliser le téléphone sans fil en
l’appuyant sur l’oreille qui se trouve dans la
direction opposée au stimulateur cardiaque.
L’étude effectuée par l’organisme WRS n’a pas
identifié de risque pour les détenteurs de simulateurs
cardiaques causés par les gens qui utilisent un
téléphone sans fil à proximité de ceux-ci.
À propos des téléphones sans fil
• Alimentation électrique: Les mêmes
caractéristiques qui constituent des avantages
pour les téléphones sans fil affichent également
des restrictions. Les appels téléphoniques sont
transmis entre le combiné sans fil et le socle par le
biais d’ondes radio ; il y a donc la possibilité que
vos conversations téléphoniques sans fil soient
interceptées par des équipements de réception
radio se trouvant dans la portée du combiné sans
fil. Pour cette raison, vous ne devez pas percevoir
les communications téléphoniques sans fil comme
étant aussi confidentielles.
• Alimentation électrique: Le socle de ce téléphone
sans fil doit être branché à une prise électrique
fonctionnelle. La prise électrique ne doit pas être
contrôlée par un interrupteur mural. Les appels ne
pourront pas être effectués du combiné sans fil si
le socle est débranché ou mis hors tension ou si le
courant est coupé.
• Possibilité d’interférences aux téléviseurs:
Certains téléphones sans fil fonctionnent sur des
fréquences pouvant causer des interférences aux
téléviseurs et aux magnétoscopes. Pour réduire
ou prévenir de telles interférences, ne placez
pas le socle du téléphone sans fil près ou sur un
téléviseur ou magnétoscope. S’il y a présence de
parasites, il est conseillé d’éloigner le téléphone
sans fil du téléviseur ou du magnétoscope afin de
réduire possiblement les interférences.
• Piles rechargeables: Manipulez les piles avec soin
afin de ne pas les court-circuiter avec des bagues,
bracelets ou clés. Les piles ou le conducteur peut
surchauffer et causer des blessures. Respectez la
polarité adéquate entre la pile et le chargeur.
• Les bloc-piles rechargeables à l’hydrure
métallique de nickel: Jetez ces blocs-piles de
manière écologique et sécuritaire. Ne les incinérez
pas et ne les percez pas. Tel que les autres piles
de ce type, elles pourraient dégager une matière
toxique qui peut causer des blessures corporelles
si elles sont brûlées ou percées.
The RBRC seal
The RBRC seal on the nickel-metal hydride battery
indicates that VTech Communications, Inc. is voluntarily
participating in an industry program to collect and
recycle these batteries at the end of their useful lives,
when taken out of service within the United States and
Canada.
The program provides a convenient alternative to
placing used nickel-metal hydride batteries into the
trash or municipal waste, which may be illegal in your
area.
VTech’s participation makes it easy for you to drop
off the spent battery at local retailers participating in
the program or at authorized VTech product service
centers. Please call
1 (800) 8 BATTERY® for information on Ni-MH battery
recycling and disposal bans/restrictions in your area.
VTech’s involvement in this program is part of its
commitment to protecting our environment and
conserving natural resources.
The RBRC seal and 1 (800) 8 BATTERY® are registered
trademarks of Call2recycle, Inc.
FCC, ACTA and IC regulations
FCC Part 15
This equipment has been tested and found to
comply with the requirements for a Class B digital
device under Part 15 of the Federal Communications
Commission (FCC) rules. These requirements are
intended to provide reasonable protection against
harmful interference in a residential installation. This
equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However,
there is no guarantee that interference will not occur
in a particular installation. If this equipment does cause
harmful interference to radio or television reception,
which can be determined by turning the equipment
off and on, the user is encouraged to try to correct
the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment
and receiver.
• Connect the equipment into an outlet on a
circuit different from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV
technician for help.
Changes or modifications to this equipment not
expressly approved by the party responsible for
compliance could void the user’s authority to operate
the equipment.
This device complies with Part 15 of the FCC rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received,
including interference that may cause undesired
operation. Privacy of communications may not be
ensured when using this telephone.
To ensure safety of users, the FCC/ISEDC has
established criteria for the amount of radio frequency
energy that can be safely absorbed by a user or
bystander according to the intended usage of the
product. This product has been tested and found
to comply with the FCC/ISEDC criteria. The handset
may be safely held against the ear of the user. The
telephone base shall be installed and used such that
parts of the user’s body other than the hands are
maintained at a distance of approximately 20 cm (8
inches) or more.
This Class B digital apparatus complies with Canadian
requirement:
CAN ICES-3 (B)/NMB-3(B).
FCC Part 68 and ACTA
This equipment complies with Part 68 of the FCC
rules and with technical requirements adopted by
the Administrative Council for Terminal Attachments
(ACTA). The label on the back or bottom of this
equipment contains, among other things, a product
identifier in the format US:AAAEQ##TXXXX. This
identifier must be provided to your telephone service
provider upon request.
The plug and jack used to connect this equipment
to premises wiring and the telephone network must
comply with applicable Part 68 rules and technical
requirements adopted by ACTA. A compliant
telephone cord and modular plug is provided with
this product. It is designed to be connected to a
compatible modular jack that is also compliant. An
RJ11 jack should normally be used for connecting to
a single line and an RJ14 jack for two lines. See the
installation instructions in the user’s manual.
The Ringer Equivalence Number (REN) is used to
determine how many devices you may connect to
your telephone line and still have them ring when
you are called. The REN for this product is encoded
as the 6th and 7th characters following the US: in the
product identifier (e.g., if ## is 03, the REN is 0.3). In
most, but not all areas, the sum of all RENs should be
five (5.0) or less. For more information, please contact
your telephone service provider.
This equipment may not be used with Party Lines. If
you have specially wired alarm dialing equipment
connected to your telephone line, ensure the
connection of this equipment does not disable your
alarm equipment. If you have questions about what
will disable alarm equipment, consult your telephone
service provider or a qualified installer.
If this equipment is malfunctioning, it must be
unplugged from the modular jack until the problem
has been corrected. Replacement to this telephone
equipment can only be made by the manufacturer or
its authorized agents. For replacement procedures,
follow the instructions outlined under the “Limited
warranty”.
If this equipment is causing harm to the telephone
network, the telephone service provider may
temporarily discontinue your telephone service. The
telephone service provider is required to notify you
before interrupting service. If advance notice is not
practical, you will be notified as soon as possible. You
will be given the opportunity to correct the problem
and the telephone service provider is required to
inform you of your right to file a complaint with the
FCC. Your telephone service provider may make
changes in its facilities, equipment, operation, or
procedures that could affect the proper functioning
of this product. The telephone service provider is
required to notify you if such changes are planned.
If this product is equipped with a corded or cordless
handset, it is hearing aid compatible.
If this product has memory dialing locations, you may
choose to store emergency telephone numbers (e.g.,
police, fire, medical) in these locations. If you do store
or test emergency numbers, please:
Remain on the line and briefly explain the reason for
the call before hanging up.
Perform such activities in off-peak hours, such as early
morning or late evening.
Industry Canada
This device contains licence-exempt transmitter(s)/
receiver(s) that comply with Innovation, Science and
Economic Development Canada’s licence-exempt
RSS(s).
Operation is subject to the following two conditions:
(1) this device may not cause interference, and (2)
this device must accept any interference, including
interference that may cause undesired operation.
Privacy of communications may not be ensured when
using this telephone.
The term ‘’IC:‘’ before the certification/registration
number only signifies that the Industry Canada
technical specifications were met.
The Ringer Equivalence Number (REN) for this terminal
equipment is 0.1. The REN indicates of the maximum
number of devices allowed to be connected to a
telephone interface. The termination on an interface
may consist of any combination of devices subject
only to the requirement that the sum of the RENs of all
the devices not exceed five.
This product meets the applicable Innovation, Science
and Economic Development Canada technical
specifications.
California Energy Commission battery
charging testing instructions
This telephone is set up to comply with the energy-
conserving standards right out of the box. These
instructions are intended for California Energy
Commission (CEC) compliance testing only. When the
CEC battery charging testing mode is activated, all
telephone functions, except battery charging, will be
disabled.
To activate the CEC battery charging testing mode:
1. Unplug the telephone base power adapter from the
power outlet. Make sure all handsets are plugged
with charged batteries before proceeding.
2. While you press and hold , plug the telephone
base power adapter back to the power outlet.
3. After about 10 seconds, when the light is steady
on, release and then press it again within two
seconds. You hear a confirmation tone. All handsets
display To register HS... and ...see manual
alternately. Allow up to one minute for the process
to complete.
If the phone fails to enter this mode, repeat all the
steps mentioned above. The telephone base will be
powered up as normal if you fail to press within
two seconds in Step 3.
To deactivate the CEC battery charging testing mode:
1. Unplug the telephone base power adapter from
the power outlet, then plug it back in. Then the
telephone base is powered up as normal.
2. Put the handsets on the telephone base cradle to
begin registration.
3. The handset shows Registering... If the registration
is successful, the handset screen displays
Registered and beeps. The handset is registered
with the telephone base.
Contents
Install | Set up 14
What’s in the box 14
Connect the telephone base 15
Connect the charger 15
Install the battery 16
Charge the battery 16
Check the battery level 17
Check for dial tone 17
Before use 18
Set date and time (before use) 18
Set up through voice guide -
Smart call blocker (before use) 18
Set up through voice guide -
Answering system (before use) 19
Overview 20
Handset 20
Telephone base 22
Display 23
Handset lights 23
Operating range 24
Introducing Bluetooth© 24
Glossary of terms 26
VTech Connect to Cell™
application 27
Bluetooth setup 27
Add a Bluetooth cell phone /
personal computer 28
Telephone base LED color
indication 29
Auto connection 29
Device list and connection 30
Review the device list 30
Remove a paired device 30
Download phonebook 31
Remote voice control 32
Operate 34
Make, answer or end a
home call 34
Make a home call 34
Predial a home call 34
Answer a home call 34
End a home call 34
Make, answer or end a
cell call 35
Make a cell call 35
Predial a cell call 35
Answer a cell call 35
End a cell call 35
View dialing options 36
Sound 36
Use speakerphone 36
Volume control 36
Mute the microphone 37
Temporary ringer silencing 37
Stream audio and music
at base 38
Join a call 38
Join a call in progress 38
Call waiting on the home line 39
Call waiting on the cell line 40
Intercom 41
Initiate an intercom call with a
cordless handset 41
Answer an incoming call during
an intercom call 42
Transfer a call via intercom 42
Find handset 43
Page/ find handset 43
Use phone menu 44
Phonebook 44
Phonebook |
Phonebook entry 44
Add a phonebook entry 45
Review the phonebook entries 46
Dial a phonebook entry 46
Edit a phonebook entry 46
Delete a phonebook entry 47
Delete all phonebook entries 47
Alphabetical search 47
Redial list 48
Review a redial list entry 48
Dial a redial list entry 48
Save a redial entry to the
phonebook 49
Delete a redial list entry 49
Chain dialing 50
Caller ID 51
Review the caller ID log 51
Save a caller ID log entry to
the phonebook 52
Save a caller ID log entry to
allow list 53
Save a caller ID log entry to
block list 53
Save a caller ID log entry to
star name list 54
Dial a caller ID log entry 54
Delete caller ID log entries 54
Caller ID memory match 55
Missed call indicator 55
Smart call blocker 56
Overview 58
Call categories 59
Welcome calls 59
Unwelcome calls 59
Calls without numbers
(for home calls only) 59
Uncategorized calls
(for home calls only) 59
Call handling 59
Contents
Set Smart call blocker on/off 62
Set profile 62
Block list 63
Add a block entry 63
Review block list entries 64
Save a caller ID log entry to
block list 65
Edit a block list entry 65
Unblock a telephone number 66
Delete all block list entries 66
Allow list 67
Add an allow list entry 67
Review allow list entries 68
Save a caller ID log entry to
allow list 68
Edit a allow list entry 69
Delete an allow list entry 69
Delete all allow list entries 70
Star name list 70
Add a star name entry 70
Review star name list entries 71
Save a caller ID log entry to
star name list 72
Edit a star name list entry 72
Delete a star name list entry 72
Delete all star name list entries 73
Voice guide to set Smart call
blocker 73
Screening announcements 74
Play your current announcement
of screening with caller name 75
Play your current announcement
of screening without caller name 75
Record your name for all
screening announcements 76
Reset all your screening
announcements 76
Allowed calls 77
Blocked calls 77
Screen unknown home calls 78
Screened call options 80
Screen robocalls 81
Option while on a call 82
Answering system 83
Difference between the built-in
answering system and voicemail
service 83
Use your built-in answering
system 84
Turn on or off the answering
system 84
Playback messages 85
Adjust listening volume during
message playback 86
Skip to the next message 86
Repeat the playing message 86
Listen to the previous message 86
Stop the message playback 86
Delete a message 86
Delete all messages 86
Answering system remote
access 87
Call intercept while using
answering system 87
Recording memo 88
Turn on or off the call screening 88
Screen a call with answering
system 89
Announcement 89
Record a new outgoing
announcement 89
Play your announcement 90
Delete your annoucement 90
Voicemail (via Tlephone
service provider) 91
Turn off the new voicemail
indicators 91
Configure | Settings 92
Answering system settings 92
Set your built-in answering
system 92
Set answering system through
voice guide 92
Set remote access code 93
Turn on or off the message
alert tone 93
Area code settings 94
Set home area code 94
Dial modes 95
Temporary tone dialing 95
Set dial mode 95
Ringer 95
Set ringer tone 95
Set ringer volume 96
Set date and time 97
Set languages 97
Set LCD language 97
Set voice language 98
Sound settings 98
Set number of rings 98
Set QUIET mode 99
Set listening volume 99
Set key tone 99
Voicemail settings 100
Set speed dial voicemail
number 100
Add and register handset 100
General product care 101
Technical specifications 102
Frequently asked questions 104
14 15
Install | Set up
What’s in the box
Your telephone package contains the
following items. Save your sales receipt
and original packaging in case it is
necessary to ship your telephone for
warranty service.
You can add new handsets (LS6300/
VS324-0) to your telephone system. All
accessories are sold separately. Your
telephone base supports a maximum of
five devices.
NOTE
• To purchase replacement batteries
or power adapters, visit our website
at www.vtechphones.com or call
1 (800) 595-9511. In Canada, go to
phones.vtechcanada.com or dial
1 (800) 267-7377.
Quick
start
guide
Introducing
Smart call
blocker
Bluetooth
feature
guide
• 1 set for LS6381/
LS6382/VS324
• 2 sets for LS6381-2/
LS6382-2/VS324-2
• 3 sets for LS6381-3/
LS6382-3/VS324-3
• 4 sets for LS6381-4/
LS6382-4/VS324-4
• 5 sets for LS6381-5/
LS6382-5/VS324-5
• 1 sets for LS6381-2/
LS6382-2/VS324-2
• 2 sets for LS6381-3/
LS6382-3/VS324-3
• 3 sets for LS6381-4/
LS6382-4/VS324-4
• 4 sets for LS6381-5/
LS6382-5/VS324-5
Connect the telephone base
TIPS
• If you want to mount the base, make
sure telephone line pass through the
mounting bracket before connecting
to the DSL filter.
• If you subscribe to digital subscriber
line (DSL) high-speed Internet
service through your telephone line,
make sure you connect a DSL filter
(not included) to the telephone wall
jack.
Connect the charger
THIS SIDE UP / CE CÔTÉ VERS LE HAUT
Battery Pack / Bloc-piles :
BT162342/BT262342 (2.4V 300mAh Ni-MH)
WARNING / AVERTISSEMENT :
DO NOT BURN OR PUNCTURE BATTERIES.
NE PAS INCINÉRER OU PERCER LES PILES.
Made in China / Fabriqué en chine CR2105
16 17
Install the battery
1. Plug the battery connector securely
into the socket inside the handset
battery compartiment.
• Make sure the battery label THIS
SIDE UP is facing up, as indicated.
THIS SIDE UP / CE CÔTÉ VERS LE HAUT
Battery Pack / Bloc-piles :
BT162342/BT262342 (2.4V 300mAh Ni-MH)
WARNING / AVERTISSEMENT :
DO NOT BURN OR PUNCTURE BATTERIES.
NE PAS INCINÉRER OU PERCER LES PILES.
Made in China / Fabriqué en chine CR2105
THIS SIDE UP
2. Align the cover flat against the battery
compartment, then slide it upwards
until it clicks into place.
CÔTÉ VERS LE HAUT
s :
42 (2.4V 300mAh Ni-MH)
ISSEMENT :
OR PUNCTURE BATTERIES.
OU PERCER LES PILES.
é en chine CR2105
Charge the battery
16 hrs
The following table summarizes the
battery indicators and actions to take.
Battery
indicators
Battery
status
Action
• The screen
is blank, or
shows Put in
charger and
flashes.
• The battery
has no
charge or
very little
charge. The
handset
cannot be
used.
• Charge
without
interruption
(at least 30
minutes).
• The screen
shows Low
battery and
flashes.
• The battery
has enough
charge to be
used for a
short time.
• Charge
without
interruption
(at least 30
minutes).
• The screen
shows
HANDSET X.
• The battery is
charged.
• To keep
the battery
charged,
place it in
the handset
charger
when not in
use.
When it is fully charged, you can expect
the following performance:
Operation • Operating time *
Talk time (cordless
handset)
• 10 hours
Standby • 5 days
* Operating times vary depending
on your actual use and the age of the
battery.
Check the battery level
After you have installed the battery,
check the battery level on the handset
screen.
• If the screen is blank, or flashes, then
the battery needs to be charged. Go
to Charge the battery section before
you do any setting or operation.
• If the battery icon is , , or , then
go to Set the date and time, Set
Smart call blocker through voice
guide and Set the answering system
through voice guide section.
Check for dial tone
Lift the corded handset, or press
HOME/FLASH on the cordless
handset. If you hear a dial tone, the
installation is successful.
If you do not hear a dial tone
• Make sure the installation procedures
are properly done.
• The handset may take a second or
two to find the telephone base and
produce a dial tone. This is normal.
Wait an extra second before dialing.
• If the previous suggestions do not
work, disconnect the telephone
line cord from your telephone and
connect the telephone line cord to
another telephone.
• If there is no dial tone on that other
telephone either, your telephone
line cord may be defective. Install a
new telephone line cord.
• If changing the telephone line
cord does not help, the wall jack
(or the wiring to this wall jack) may
be defective. Try using a different
wall jack in your home to connect
your LS6381/LS6381-2/LS6381-3/
LS6381-4/LS6381-5/LS6382/LS6382-
2/LS6382-3/LS6382-4/LS6382-5/
VS324/VS324-2/VS324-3/VS324-4/
VS324-5 telephone, or contact your
telephone service provider (charges
may apply).
18 19
Before use
Set date and time (before use)
After you install your telephone or
power returns following a power outage
and battery depletion, the handset will
prompt you to set the date and time, and
to configure the Smart call blocker and
answering system through voice guide.
NOTE
• Make sure you set the date and
time including the year correctly;
otherwise the answering system does
not announce the correct day of the
week for your recorded messages
time stamp.
1. Use the dialing keys (0-9) to enter the
month (MM), date (DD) and year (YY).
Then, press .
2. Use the dialing keys (0-9) to enter the
hour (HH) and minute (MM). Then
press q CID or p to choose AM
or PM.
3. Press to save.
After setting the date and time, the
handset will prompt if you want to set
Smart call blocker (before use).
TIP
• To skip setting the date and time,
press on the handset.
Set up through voice guide - Smart call
blocker (before use)
After the date and time setting is done or
skipped, the handset will then prompt if
you want to set up Smart call blocker.
This feature is an easy and alternative way
for you to do the basic setup of Smart call
blocker.
You can follow the voice guide to set your
telephone system to allow or to screen
all incoming home calls.
1. Press to start the Smart
call blocker setup via voice guide. You
hear the voice prompt “ Hello! This
voice guide will assist you with the
basic setup of Smart call blocker...”
• To skip the set up, press
on the handset.
2. Set up your Smart call blocker feature
by inputting the designated numbers,
as instructed in the voice guide.
After setting Smart call blocker, the
handset will prompt if you want to set
Answering system (before use).
Set up through voice guide - Answering
system (before use)
This feature assists you to do the basic
setup of the answering system. You can
follow the voice guide to record your
own announcement, set the number of
rings and the message alert tone.
1. Press to start the
answering system setup via voice
guide. You hear the voice prompt “
Hello! This voice guide will assist you
with the basic setup of your answering
system.”
• To skip the set up, press
on the handset.
2. Setup your answering system by
inputting the designated numbers as
instructed in the voice guide.
Alternate way to set up Smart call
blocker
1. Press CALL BLOCK on the handset to
enter Smart call blocker menu.
- OR -
Press to enter the
main menu. Press q CID or p to
scroll to Smart call blk, and then press
.
2. Press q CID or p to scroll to Voice
guide, the press . You
hear the voice prompt “Hello! This
voice guide will assist you with the
basic setup of Smart call blocker...”
3. Set up your Smart call blocker by
inputting designated numbers as
instructed in the voice guide.
NOTE
• You can press on the
handset to quit the voice guide at any
time.
20 21
Alternate way to set up Answering
system
1. Press on the handset
in idle mode.
2. Press q CID or p to scroll to
Answering sys, and then press
.
3. Press q CID or p to scroll to Voice
guide, the press . You
hear the voice prompt “This voice
guide will assist you with the basic
setup of your answering system.”
4. Set up your answering system by
inputting designated numbers as
instructed in the voice guide.
NOTE
• You can press on the
handset to quit the voice guide at any
time.
Overview
Handset
1
4
7
5
9
8
11
6
2
3
13
14
12
15
16
10
1LCD display
2CHARGE light
3MENU/
SELECT
• Display the menu.
• Select an item or save an
entry or setting while in
the menu.
4VOICE
• Activate the voice-
controlled application
of one of the connected
devices when the system
is in idle. If there is no
paired device, then the
handset will prompt Pair
cell first to remind you
for remote voice control
activation.
5
OFF/
CANCEL
• Hang up a call.
• Return to the previous
menu or idle mode
without making changes.
• Delete digits while
predialing.
• Silence the handset
ringer temporarily while
the phone is ringing.
• Press and hold to erase
the missed call indicator
while the handset is not
in use.
6 OPER 0 • Enter space character
during text editing.
7QUIET #
• Press and hold to set
and turn on the QUIET
mode, or turn it off.
• When reviewing a
caller ID log entry, press
repeatedly to view
other dialing options.
8CALL BLOCK
• Block the incoming call
when the telephone is
ringing.
• When on a call, press to
block the call.
• Show the Smart call
blocker menu when idle.
9MUTE/
DELETE
• Mute the microphone
during a call.
• Mute the ringer
temporarily when the
handset is ringing.
• Delete an individual entry
while reviewing the caller
ID log, the phonebook or
the redial memory.
• Delete digits while
predialing.
• Delete the playing
message or the
recorded announcement
during message or
announcement playback.
10 • Show phonebook entries.
CID • Review the caller ID log.
10 pVOLUME/
VOLUMEq
• Move the cursor to the
left or right while entering
names or numbers.
• Increase or decrease the
listening volume when
on a call, or increase or
decrease the message
playback volume.
11 REDIAL/
PAUSE
• Review the redial list.
• Insert a dialing pause
while dialing or entering
numbers into the
phonebook.
12 CELL
• Make or answer a cell
call.
• Answer an incoming cell
call when you hear a call
waiting alert during a cell
call.
• Call back the caller if
the caller’s number is
available while reviewing
caller ID log.
13 HOME/
FLASH
• Make or answer a home
call.
• Answer an incoming
home call when you hear
a call waiting alert.
• Call back the caller if
the caller’s number is
available while reviewing
caller ID log.
14 1
• While reviewing a caller
ID log entry, press
repeatedly to add or
remove 1 in front of
the telephone number
before dialing or saving it
in the phonebook.
• Press and hold to set
or dial your voicemail
number.
15 TONE /
aA
• Switch to tone dialing
temporarily during a call
if you have pulse service.
• Change the next letter to
upper or lower case while
entering names.
22 23
16
• Make or answer a home
call or cell call using the
speakerphone.
• Turn on or off the handset
speakerphone.
Telephone base
2
3
5
4
1
6
7
8
9
1Charging pole
2
(Volume
up)
• Increase the base’s
speaker/ringer volume.
3
(Volume
down)
• Decrease the base’s
speaker/ringer volume.
4
(Cell line)
• Answer a cell call.
• LED flashes quickly when
there is an incoming cell
call.
• LED flashes slowly when
the cell line is in use.
5(Home line)
• Answer a home call.
• LED flashes quickly when
there is an incoming
home call.
• LED flashes slowly when
the home line is in use.
6
• Page all system handsets.
• Answer an incoming
home or cell call when
you receive a call waiting
alert.
7
(Device 1
/ Device 2
slots)
• Press to switch between
device 1 slot and device
2 slot.
• Press and hold for four
seconds to add a cell
phone or personal
computer.
• Blue LED is steady on
when the telephone
paired and connected a
Bluetooth device.
• Blue LED flashes while
pairing a Bluetooth
device.
• Purple LED is steady on
when in auto-connection
mode.
• Red LED is steady on
when no device paired or
pairing has failed.
• When LED is off, press
to connect a paired
Bluetooth device.
8
(Answering
system)
• Turn the built-in
answering system on or
off.
• LED is steady on when
answering system is on.
• LED flashes when there
are new messages.
9
(Mute)
• Mute the microphone
during a call.
• LED flashes when
microphone is muted.
• Silence the ringer
temporarily while the
telephone base is ringing.
Display
HANDSET 1
ECO
10:30PM 10/16
MSG #
NEW
ANS ON
1
• The handset battery
is low and needs
charging.
2• The handset battery
is charging.
3• The handset battery
is fully charged.
4• Ringer is off.
5
• New voicemail
received from your
telephone service
provider.
6NEW
• The entry you are
reviewing is new in
the caller ID log.
7• Displays when
Home line is in use.
8• Bluetooth device is
paired and active.
9• Bluetooth device /
Cell line is in use.
10 ANS ON • Answering system is
on.
11
MSG#
5/10
• Handset displays
the current message
number being
played and the total
number of new/old
messages recorded.
12 ECO
• The ECO
mode activates
automatically to
reduce power
consumption when
the handset is
within range of the
telephone base.
Handset lights
1CHARGE
• On when the
handset is charging
in the handset
charger.
2
• On when the
speakerphone is in
use.
24 25
Operating range
This cordless telephone operates with
the maximum power allowed by the
Federal Communications Commission
(FCC). Even so, this handset and
telephone base can communicate over
only a certain distance which can vary
with the locations of the telephone base
and handset, the weather, and the layout
of your home or office.
When the handset is out of range, the
handset displays Out of range or no pwr
at base.
If there is a call while the handset is out of
range, it may not ring, or if it does ring,
the call may not connect well when you
press HOME/FLASH. Move closer
to the telephone base, and then press
HOME/FLASH to answer the call. If
the handset moves out of range during
a telephone conversation, there may
be interference. To improve reception,
move closer to the telephone base.
Introducing Bluetooth©
Your new LS6381/LS6381-2/LS6381-3/
LS6381-4/LS6381-5/LS6382/LS6382-2/
LS6382-3/LS6382-4/LS6382-5/VS324/
VS324-2/VS324-3/VS324-4/VS324-5
telephone system with Bluetooth wireless
technology has the following features:
• Pair up to two Bluetooth enabled
devices (cell phones or personal
computers) with the telephone base.
• Connect one cell phone at a time to
make and receive cell calls.
• Receive calls using your cell phone
service with your telephone base or
system handsets.
• Download phonebook entries from
your cell phone.
• Stream audio and music from your
cell phone or personal computer to
the telephone base.
IMPORTANT INFORMATION
• Your LS6381/LS6381-2/LS6381-3/
LS6381-4/LS6381-5/
LS6382/LS6382-2/LS6382-3/
LS6382-4/LS6382-5/VS324/
VS324-2/VS324-3/VS324-4/VS324-5
is compatible with Bluetooth version
2.0 or above devices.
• After plugging in the telephone
base, wait at least 20 seconds before
connecting a Bluetooth device.
• Refer to the user’s manual of your
Bluetooth enabled cell phone
or personal computer for more
information about how that device
uses Bluetooth connectivity.
• Bluetooth wireless technology
operates within a short range (a
maximum of approximately 15 feet)
from the telephone base. Keep
connected cell defvices within this
range.
Cellular signal
Less than 15
feet for optimal
performance
LS6381/LS6382/VS324
series
®
• If your Bluetooth device has
poor reception in your home,
the LS6381/LS6381-2/LS6381-3/
LS6381-4/LS6381-5/
LS6382/LS6382-2/LS6382-3/
LS6382-4/LS6382-5/VS324/
VS324-2/VS324-3/VS324-4/
VS324-5 cannot improve the
reception. However, if there is
a location in your house with
better reception, you can leave
your Bluetooth device at that
location while you use the
LS6381/LS6381-2/LS6381-3/
LS6381-4/LS6381-5/
LS6382/LS6382-2/LS6382-3/
LS6382-4/LS6382-5/VS324/
VS324-2/VS324-3/VS324-4/VS324-5
cell line. For optimal performance,
the device must be within 15 feet of
the telephone base.
• If you experience poor sound quality,
it may be caused by the distance
between your Bluetooth device and
the telephone base. To improve the
performance, place your device
closer to the telephone base (within
15 feet) and make sure that there are
no physical obstacles such as large
furniture or thick wall in between.
• Charge your cell phone while it is
connected to the telephone base.
Your cell phone’s battery discharges
faster while it is connected to the
telephone base via Bluetooth
wireless technology.
• Monitor your cell phone’s usage,
because minutes may be deducted
from your cellular plan for the
duration of all cell calls, depending
on the terms of your plan.
Refer to the Bluetooth setup section
to learn how to set up your Bluetooth
device. Refer to the Telephone
operation section on how to operate
your Bluetooth devices with your new
telephone system with Bluetooth
wireless technology.
The Bluetooth® word mark and logos are owned
by Bluetooth SIG, Inc. and any use of such marks
by Advanced American Telephones and its
parent, VTech Holdings Limited, is under license.
VTech
Holdings Limited is a member of Bluetooth SIG,
Inc. Other trademarks and trade names are those
of their respective owners.
26 27
Glossary of terms
Below are some terms used in this user’s
manual to help you become familiar with
using your Bluetooth devices and your
new VTech telephone system.
Active device slots - the Device list has
two active slots for two cell phones or
personal computers. In order to use a
Bluetooth device on a call, it must be in
an active slot and be connected.
Bluetooth cell phone - refers to a mobile
Bluetooth enabled cellular telephone.
CELL line - the telephone line associated
with your cell phone service. Press
CELL on your handset or on the
telephone base to use the cell line.
Connected - when you pair a Bluetooth
device to your telephone system, it is
placed in an active slot and automatically
connected. When a device is connected,
a 1 and/or 2 will display after on the
handset screen. If a device loses its
connection to the telephone base, it must
be reconnected before you can use the
device with the telephone system.
Device list - The list of devices that have
been paired to the telephone. You can
pair up to 2 Bluetooth enabled devices
(cell phones or personal computers).
Disconnected - when device(s) is/are
disconnected, 1 and/or 2 is/are not
displayed on the handset screen.
Discoverable mode - before a Bluetooth
enabled device can be paired, it must
be set to this mode. When pairing your
cell phone, the telephone base will be
set to this mode. Depending on the
manufacturer, this mode is sometimes
referred to as Find Me or Visibility.
HOME line - your conventional telephone
land line. On your telephone system,
press HOME/FLASH on the handset
or on the telephone base to use the
home line.
Paired devices - The Bluetooth enabled
devices (cell phones or personal
computers) that have shared registration
information with the telephone base. A
total of two Bluetooth enabled devices
can be paired to the telephone base.
However, only one paired device can
communicate with the base at a time.
Pairing - sometimes referred to as
bonding. The process of sharing
registration information between
two Bluetooth enabled devices. Your
Bluetooth enabled cell phone or
personal computer must first be paired
to the telephone base in order to use it
with this telephone system.
VTech Connect to Cell™ application
If you are using Bluetooth-enabled
Android® phones (OS 2.3 or higher),
you can further extend the flexibility of
your telephone system with use of the
free Connect To Cell application.
VTech Connect to Cell comprises Caller
ID manager and Alerts manager that
help you integrate your cell phone with
your new telephone system.
To learn more or download this
application via Google Play® Store, go to
https://www.vtechphones.com/app_
connect_to_cell.
Bluetooth setup
To use a Bluetooth enabled device
with your LS6381/LS6381-2/LS6381-3/
LS6381-4/LS6381-5/LS6382/LS6382-2/
LS6382-3/LS6382-4/LS6382-5/VS324/
VS324-2/VS324-3/VS324-4/
VS324-5, you must first pair and
connect it with the telephone base.
The LS6381/LS6381-2/LS6381-3/
LS6381-4/LS6381-5/LS6382/LS6382-2/
LS6382-3/LS6382-4/LS6382-5/VS324/
VS324-2/VS324-3/VS324-4/
VS324-5 telephone base and all system
handsets can be used to make or answer
calls on the cell phone line.
Bluetooth wireless technology operates
within a short range (up to 15 feet).
When you pair a Bluetooth device to
the telephone base, keep the device
within 15 feet of the telephone base for
optimal performance.
28 29
Add a Bluetooth cell phone / personal
computer
You can pair up to two cell phones or
personal computers to the telephone.
To use a paired device, it must be paired
and connected.
Before you begin, make sure that you
have cellular coverage and your Bluetooth
enabled cell phone is not connected to
any other Bluetooth device. Refer to your
cell phone user’s manual to learn how to
search for or add new Bluetooth devices.
Select a device slot:
1. Press on the telephone base in
idle mode to select a Bluetooth device
slot.
• Each press toggles between slot 1
and slot 2.
• The LED of the selected device
slot lights up and indicates the
device status in different colors.
Add a cell phone / PC:
2. After selecting a device slot, press and
hold on the telephone base for 4
seconds to enter pairing mode.
3. When the LED of the selected slot is
flashing blue, turn on the Bluetooth
feature of your cell phone or PC and
search for or add new devices.
• Once your device finds your
telephone (VTech DECT 6.0),
press the appropriate key on your
device to continue the pairing
process.
4. When a Bluetooth device is
successfully paired and connected
to the telephone, the LED of the
selected slot will turn to steady blue.
The handset screen will display 1
(slot 1) or 2 (slot 2).
HANDSET 1
ECO
1
10:30PM 11/22
NOTES
• The pairing process may take up to
one minute. If the pairing process
fails, try again.
• The steps for the pairing process
may vary for different cell phones.
If this happens, follow the prompts
on your cell phone and your
LS6381/LS6381-2/LS6381-3/
LS6381-4/LS6381-5/
LS6382/LS6382-2/LS6382-3/
LS6382-4/LS6382-5/VS324/
VS324-2/VS324-3/VS324-4/
VS324-5 to complete the pairing
process.
• Refer to the user’s manual of device
on how to search for or add a new
Bluetooth device.
Telephone base LED color indication
The telephone base’s slot 1 and slot
2 LEDs show different colors when
operating with the Bluetooth features.
Selected
slot 1/2 LED
colors
LED color
indication of
selected slot
Blue Flashing Telephone base
tries to pair with
your Bluetooth
device.
Blue Steady
on
Paired and
connected. Ready
to use.
Red Steady
on
No Bluetooth
device is paired or
pairing failed.
Purple Steady
on
Paired but lost
connection.
Telephone enters
auto-connection
mode for 60
minutes.
Off Paired but auto-
connection mode is
timed out.
Press on the
telephone base to
turn on the auto-
connection mode.
Auto connection
When an active device moves within
Bluetooth range of the telephone
base, or is turned on within range, the
telephone base tries to connect to the
device. When the device moves out of
range, it is disconnected. Your device
might make a connect or disconnect
sound.
A connected device could also be
disconnected by:
• Turning off the Bluetooth device.
• Turning off the Bluetooth feature of
the device.
• The Bluetooth device is not within
range of the telephone base.
The telephone will try to auto-connect
to the devices that have disconnected
within 60 minutes. When auto-
connection is timed out, the LED of the
selected device slot will turn off.
To enter auto-connection mode
• Press on the telephone base,
the last selected device slot will start
connect to the disconnected device.
• Each press toggles between slot
1 and slot 2.
30 31
Device list and connection
Up to 2 devices can be paired to the
telephone base. All paired devices are
shown on the device list. To use a paired
device, it must be connected and in an
active slot (1: or 2:) on the device list. Both
Bluetooth enabled devices can be used
on a cell call at a time.
NOTE
• When connecting a Bluetooth device
to the device list, all connected devices
will be temporarily disconnected until
the procedure is complete. It may take
up to two minutes to reconnect.
Review the device list
You can check what devices you have
paired to the telephone system.
1. Press MENU/SELECT on the handset
in idle mode to enter the main menu.
2. Press qCID or p to
highlight Bluetooth, then press
MENU/SELECT.
3. Press MENU/SELECT again to select
Device list.
NOTE
• When a device (1: or 2:) is displayed
on the handset screen, press
MUTE/DELETE will remove the device.
Remove a paired device
When you already have 2 devices on the
device list and you want to add another
device, you must first delete one from
the list. You can only pair 2 cell phones or
personal computers.
To remove a paired device:
1. Press MENU/SELECT on handset in
idle mode to enter the main menu.
2. Press qCID or p to
highlight Bluetooth, then press
MENU/SELECT.
3. Press qCID or p to
highlight Device list, then press
MENU/SELECT.
4. Press qCID or p to highlight
the desired device, then press
MUTE/DELETE.
Download phonebook
You can download cell phone
phonebook entries to your
LS6381/LS6381-2/LS6381-3/
LS6381-4/LS6381-5/LS6382/LS6382-2/
LS6382-3/LS6382-4/LS6382-5/VS324/
VS324-2/VS324-3/VS324-4/
VS324-5 telephone system via
Bluetooth wireless technology. Each
downloaded cell phone phonebook
entry are stored in the telephone
phonebook with up to 30 digits for
each phone number and 15 characters
for each name.
Before downloading a phonebook,
make sure the cell phone is paired,
active, and connected to your
telephone system. Place your cell
phone next to the telephone base
when you download a cell phone
phonebook to your telephone system.
To download a cell phone phonebook:
1. Press MENU/SELECT in idle mode
to enter the main menu.
2. Press qCID or p to
highlight Bluetooth, then press
MENU/SELECT.
3. Press qCID or p to highlight
Download PB, then press
MENU/SELECT.
• If you have two paired devices,
the handset displays Select a
device briefly.
• If there is no cell phone paired to
the system, the handset displays
Pair cell first and then returns to
the previous menu.
4. Press qCID or p to highlight a
device, then press MENU/SELECT.
• If the selected device is not
available, the handset returns to
the previous menu.
During the download, the handset
flashes Downloading.... All other
idle system handsets display
Downloading....
5. When the downloading process
completes or when the memory is
full, the handset displays Entries
added: XXX. Then the handset
returns to the Bluetooth menu.
NOTES
• Cell phone contacts can be
downloaded from the phone
memory only. You can transfer the
contacts from your SIM card to your
cell phone memory first, and then
download from your cell phone
memory. For more information
on how to transfer contacts from
your SIM card to your cell phone
memory, see the user’s manual of
your cell phone.
• When downloading the phonebook
from your Bluetooth enabled cell
phone, some data may not transfer.
For example, if you have home,
mobile and work numbers for a
particular contact, the three category
descriptions may not transfer to your
telephnone system.
1:Cellphone X
ECO
2:PC X
ECO
32 33
Remote voice control
If you have connected a cell phone
to the LS6381/LS6381-2/LS6381-3/
LS6381-4/LS6381-5/LS6382/LS6382-2/
LS6382-3/LS6382-4/LS6382-5/VS324/
VS324-2/VS324-3/VS324-4/
VS324-5 telephone system, you can
activate the voice-controlled application
(voice app) of the cell phone, such as
Siri®, Google NowTM or S Voice®, using
your handset or telephone base.
The remote voice control feature works
with:
Voice-
controlled
application
Siri Google
Now
S Voice
Operation
System
(Versions
supported)
iOS (8 or
above)
Android
(4 or
above)
Android
(4 or
above)
Before using the remote voice control
feature, make sure you checked the
following:
• Your cell phone is paired and
connected to your telephone system
via Bluetooth.
• No Bluetooth applications are running
in the background of your cell phone.
• Keep your cell phone within 15 feet of
the telephone base.
• Do not lock up your cell phone’s
screen or set passcode for activating
the voice app.
• Make sure you have turned on or
logged in to the applications on your
cell phone that you will be sending
your voice commands, such as GPS,
e-mail and social networking accounts.
• Your cell phone’s data or Wi-Fi signal
is in full strength and your cell phone
can connect to the Internet.
• Try to activate the voice app on your
cell phone to ensure it is in place.
Activate remote voice control
1. Press VOICE on the handset.
• If you have connected two
devices to the telephone, the
telephone shows Select a device:.
Press qCID or p to highlight
the desired device, then press
MENU/SELECT.
• If there is no cell phone paired to
the system, the handset displays
Pair cell first and then returns to the
previous menu.
• If the activation fails, the telephone
displays Not available.
- OR -
Press and hold on the telephone
base.
2. When the telephone plays the
confirmation tone as forwarded
by the cell phone’s voice app, start
speaking toward the telephone
base or handset, and then wait for
feedback. Make reply to the voice
app’s feedback, if necessary.
• You can press on the handset
to turn off the speakerphone and
listen to the feedback through the
handset earpiece.
3. To end the current remote voice
control session, press OFF/CANCEL
on the handset or press on the
telephone base. You can restart
by following Steps 1-2 mentioned
above.
NOTES
• Once you have activated the remote
voice control feature, you are using
your cell phone’s voice app to
operate your cell phone.
• Please check the cell phone user’s
manual and the voice app’s help
topics to find out what commands
you can use and any limitations of
the voice app.
• Some cell phone manufacturers
or network carriers may customize
the phone’s operating system and
implement their own voice app. If
you want to use Google Now, you
need to manually set it as your default
voice app. For detailed instructions,
refer to your cell phone user’s
manual, or contact your cell phone’s
manufacturer or network carrier. You
may also go to “Google Product
Forums” on the Internet and check
the corresponding help topics.
• Due to the settings of certain cell
phones and voice apps, your cell
phone may not support the remote
voice control feature. Contact
your cell phone’s manufacturer or
network carrier, or check the voice
app’s help topics if you encounter
any problems.
Siri® is a registered trademark of Apple Inc.
Google NowTM is a trademark of Google Inc.
S Voice® is a registered mark of Samsung Electronics
Co., Ltd.
IOS is a trademark or registered trademark of Cisco in
the U.S. and other countries and is used under license.
HANDSET 1
ECO
1
2
10:30PM 11/20
Cell phone X 00:05
ECO
1
2
34 35
• During the remote voice control
activation, if your Android cell phone
comes with both a dedicated voice
app and Google Now, it may prompt
you to select which voice app to use,
and whether use it for just once or
always. Select the desired options.
If you do not respond to your cell
phone’s prompt in time, the handset
screen will return to idle, and the
icon will disappear. You can restart by
following Steps 1-3 mentioned above.
• If you receive a landline or cell line
incoming call when you have activated
remote voice control on a connected
cell phone, the remote voice control
operation will be ended.
• The feature may be ended
automatically by your cell phone.
For example, a cell call has been
established via the remote voice
control feature and the call has just
ended.
• If you need to press dialing keys (0-9,
TONE or QUIET#) during a cell call,
please make the call using the cell
lines of your telephone system instead
of using the voice app via the remote
voice control feature (see Make,
answer or end a cell call section).
Operate
Make, answer or end a home
call
Make a home call
Using a cordless handset
Press HOME/FLASH or on the
handset, then enter the telephone
number.
Predial a home call
Using a cordless handset
Enter the telephone number, then press
HOME/FLASH or to dial.
• When entering numbers, press
or to
make corrections.
Answer a home call
Using a cordless handset
Press HOME/FLASH or , or any
dialing keys (0-9 or or QUIET#).
Using the telephone base
Press .
End a home call
Using a cordless handset
Press or put the handset in
the handset charger.
Using the telephone base
When you are using the base
speakerphone, press .
NOTES
• The screen displays Unable to call if
the telephone line is in use.
• The screen shows the elapsed time
as you talk (in hours, minutes and
seconds).
• When entering numbers, press
and hold to insert a
dialing pause (a P appears).
Make, answer or end a cell
call
Make a cell call
Using a cordless handset
Press CELL on the handset, then enter
the telephone number.
Predial a cell call
Using a cordless handset
Enter the telephone number, then press
CELL to dial.
• When entering numbers, press
or to
make corrections.
Answer a cell call
Using a cordless handset
Press CELL or , or any dialing keys
(0-9 or or QUIET#).
Using the telephone base
Press .
End a cell call
Using a cordless handset
Press or put the handset
in the handset charger.
Using the telephone base
Press .
36 37
View dialing options
Although the caller ID log entries may
contain 10 digits (the area code plus
the 7-digit number), in some areas, you
may need to dial only the seven digits,
or 1 plus the seven digits, or 1 plus the
area code plus the seven digits. You can
change the number of digits that you
dial from the caller ID log or store to the
phonebook.
While reviewing the caller ID log, press
# (pound key) repeatedly to show
different dialing options for local and
long distance numbers before dialing
or saving the telephone number in the
phonebook.
Press 1 repeatedly if you need to add
or remove 1 in front of the telephone
number before dialing or saving it in the
phonebook.
When the number shows the correct
format for dialing:
Press HOME/FLASH or on the
handset to call the number.
Sound
Use speakerphone
Handset speakerphone
During a call, press to switch between
the speakerphone and normal handset
use.
To hand up, press or return
the handset to handset charger.
Volume control
To adjust the listening volume on a
cordless handset
During a call, press VOLUMEq or
VOLUMEp to adjust the listening
volume.
To adjust the listening volume at the
telephone base
During a call, press or .
NOTES
• The handset and speakerphone
volume settings are independent.
• When the volume reaches the
minimum or maximum setting, you
hear two beeps.
Mute the microphone
Use the mute function to turn off the
microphone. You can hear the caller,
but the caller cannot hear you.
To mute a call
Using a handset:
While on a call, press .
The handset screen displays Muted until
the mute function is turned off.
Using the telephone base:
While on a call, press on the telephone
base.
To end mute a call
Using a handset:
Press on the handset
again and resume speaking. The handset
screen briefly displays Microphone on.
Mute is automatically cancelled when
you end the call.
Using the telephone base:
Press on the telephone base and
resume speaking.
Temporary ringer silencing
When the telephone is ringing, you can
temporarily silence the ringer of the
handset without disconnecting the call.
The next call rings normally at the preset
volume.
To silence the handset ringer
Press or
on the handset. The handset screen
shows Ringer muted and .
To silence the telephone base ringer
Press on the telephone base.
38 39
Stream audio and music at
base
1. Make sure your cell phone or personal
computer is paired and connected.
Music or audio played on your device
will automatically transfer to the
telephone base.
2. Press on the telephone base to
play or pause the music.
Use your connected cell phone or
personal computer to make further
controls, for example, skip tracks or end
cell calls.
Some third party apps or software may
not be fully operated due to their designs
and regional supports. They can subject
to changes without prior notice.
NOTE
• You can press to switch between
device slot 1 or slot 2, even when
streaming audio or music at the
telephone base.
Join a call
Join a call in progress
You can use two cordless handsets, or
a cordless handset and the telephone
base at a time on an outside call. Another
handset or the telephone base can
join you on a home or cell call. The call
continues until all parties hang up.
To join a call with a cordless handset
• When a handset is already on a call,
press HOME/FLASH or on
another handset to join the call.
• Press or place the
handset in the handset charger to exit
the call. The call continues until both
devices hang up.
To join a call with the telephone base
• When a handset is already on a home
or cell call, press on the telephone
base to join a home call or press to
join the cell call.
Call waiting on the home line
If you subscribe to call waiting service
from your telephone service provider,
and someone calls while you are already
on a call on the home line, the handset
flashes , and you hear an alert tone.
Using a cordless handset
1. Press HOME/FLASH on the
handset to put your current call on
hold and take the new call.
2. Press HOME/FLASH on the
handset at any time to switch back
and forth between calls.
Using the telephone base
1. Press on the telephone base to
put your current call on hold and
take the new call.
2. Press on the telephone base at
any time to switch back and forth
between calls.
If you also subscribe to caller ID
service, it will let you see the name and
telephone number of the caller during
call waiting.
It may be necessary to change your
telephone service to use this feature.
Contact your telephone service provide
if:
• You have both caller ID and call
waiting, but as separate service
(you may need to combine these
service);
• You have only caller ID service, or
only call waiting service; or
• You do not subscribe to caller ID or
call waiting services.
There are fees for caller ID services. In
addition, services may not be available
in all areas.
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
VTech LS6381-4 Manuel utilisateur
- Catégorie
- Téléphones
- Taper
- Manuel utilisateur
dans d''autres langues
- English: VTech LS6381-4 User manual