Ryobi tss100l1 Manuel utilisateur

OPERATOR’S MANUAL

MANUEL D’UTILISATION

MANUAL DEL OPERADOR

10 in. SLIDING COMPOUND

MITER SAW WITH LASER

DE 254 mm (10 po) SCIE À ONGLETS

COMBINÉS COULISSANTE AVEC

LASER

SIERRA INGLETEADORA

COMPUESTA DESLIZANTE DE

254 mm (10 pulg.) CON GUÍA LÁSER

TSS100L1

SAVE THIS MANUAL FOR FUTURE REFERENCE

Your miter saw has been engineered and manufactured to our high standard for dependability, ease of operation, and

operator safety. When properly cared for, it will give you years of rugged, trouble-free performance.

WARNING: To reduce the risk of injury, the user must read and understand the operator’s manual before using

this product.

Cette scie à onglets a été conçue et fabriquée conformément à

nos strictes normes de fiabilité, simplicité d’emploi et sécurité

d’utilisation. Correctement entretenue, elle vous donnera des années

de fonctionnement robuste et sans problème.

AVERTISSEMENT : Pour réduire les risques de

blessures, l’utilisateur doit lire et veiller à bien comprendre le

manuel d’utilisation avant d’employer ce produit.

Su sierra ingleteadora ha sido diseñada y fabricada de conformidad

con las estrictas normas para brindar fiabilidad, facilidad de uso

y seguridad para el operador. Con el debido cuidado, le brindará

muchos años de sólido y eficiente funcionamiento.

ADVERTENCIA: Para reducir el riesgo de lesiones,

el usuario debe leer y comprender el manual del operador antes

de usar este producto.

CONSERVER CE MANUEL POUR

FUTURE RÉFÉRENCE

GUARDE ESTE MANUAL PARA

FUTURAS CONSULTAS

2 — English

 Introduction ..................................................................................................................................................................... 2

 Warranty .......................................................................................................................................................................... 2

 General Safety Rules .................................................................................................................................................... 3-4

 Specific Safety Rules ....................................................................................................................................................4-5

Symbols ........................................................................................................................................................................... 6

 Electrical .......................................................................................................................................................................... 7

 Glossary of Terms ............................................................................................................................................................ 8

 Features ......................................................................................................................................................................9-11

 Tools Needed ................................................................................................................................................................. 11

 Loose Parts ................................................................................................................................................................... 12

 Assembly .................................................................................................................................................................. 13-20

 Operation ..................................................................................................................................................................21-30

 Adjustments ..............................................................................................................................................................31-32

 Maintenance .................................................................................................................................................................. 33

 Parts Ordering / Service ................................................................................................................................... Back page

TABLE OF CONTENTS

INTRODUCTION

This tool has many features for making its use more pleasant and enjoyable. Safety, performance, and dependability have

been given top priority in the design of this product making it easy to maintain and operate.

WARRANTY

RYOBI® POWER TOOL - LIMITED THREE YEAR WARRANTY AND 90 DAY EXCHANGE POLICY

One World Technologies, Inc., warrants its RYOBI®

power tools with the following conditions:

90-DAY EXCHANGE POLICY: During the first 90 days after date of purchase, you may either request service under this

warranty or you may exchange any RYOBI® power tool which does not work properly due to defective workmanship or

materials by returning the power tool to the dealer from which it was purchased. To receive a replacement power tool or

requested warranty service, you must present proof of purchase and return all original equipment packaged with the original

product. The replacement power tool will be covered by the limited warranty for the balance of the three year period from

the date of the original purchase.

WHAT THIS WARRANTY COVERS: This warranty covers all defects in workmanship or materials in your RYOBI® power

tool for a period of three years from the date of purchase. With the exception of batteries, power tool accessories are war-

ranted for ninety (90) days. Batteries are warranted for three years.

HOW TO GET SERVICE: Just return the power tool, properly packaged and postage prepaid, to an Authorized Service

Center. You can obtain the location of the Service Center nearest you by contacting a service representative at One World

Technologies, Inc., P.O. Box 1207, Anderson, SC 29622-1207, by calling 1-800-525-2579 or by logging on to www.ryobi-

tools.com. When you request warranty service, you must also present proof of purchase documentation, which includes

the date of purchase (for example, a bill of sale). We will repair any faulty workmanship, and either repair or replace any

defective part, at our option. We will do so without any charge to you. We will complete the work in a reasonable time, but,

in any case, within ninety (90) days or less.

WHAT’S NOT COVERED: This warranty applies only to the original purchaser at retail and may not be transferred. This

warranty only covers defects arising under normal usage and does not cover any malfunction, failure or defects resulting

from misuse, abuse, neglect, alteration, modification or repairs by other than Authorized Service Centers. One World Tech-

nologies, Inc. makes no warranties, representations or promises as to the quality or performance of its power tools other

than those specifically stated in this warranty.

ADDITIONAL LIMITATIONS: Any implied warranties granted under state law, including warranties of merchantability or

fitness for a particular purpose, are limited to three years from the date of purchase. One World Technologies, Inc. is not

responsible for direct, indirect, or incidental damages, so the above limitations and exclusions may not apply to you. This

warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

3 — English

GENERAL SAFETY RULES

WARNING:

Read and understand all instructions. Failure to follow

all instructions listed below, may result in electric shock,

fire and/or serious personal injury.

READ ALL INSTRUCTIONS

 KNOW YOUR POWER TOOL. Read the operator’s manual

carefully. Learn the applications and limitations as well

as the specific potential hazards related to this tool.

 GUARD AGAINST ELECTRICAL SHOCK BY PREVENT-

ING BODY CONTACT WITH GROUNDED SURFACES.

For example: pipes, radiators, ranges, refrigerator enclo-

sures.

 KEEP GUARDS IN PLACE and in good working order.

 REMOVE ADJUSTING KEYS AND WRENCHES. Form

habit of checking to see that keys and adjusting wrenches

are removed from tool before turning it on.

 KEEP WORK AREA CLEAN. Cluttered areas and benches

invite accidents. DO NOT leave tools or pieces of wood

on the tool while it is in operation.

 DO NOT USE IN DANGEROUS ENVIRONMENTS. Do

not use power tools in damp or wet locations or expose

to rain. Keep the work area well lit.

 KEEP CHILDREN AND VISITORS AWAY. All

visitors should wear safety glasses and be kept a safe

distance from work area. Do not let visitors contact

tool or extension cord while operating.

 MAKE WORKSHOP CHILDPROOF with padlocks,

master switches, or by removing starter keys.

 DON’T FORCE THE TOOL. It will do the job better and

safer at the feed rate for which it was designed.

 USE THE RIGHT TOOL. Do not force the tool or attach-

ment to do a job for which it was not designed.

 USE THE PROPER EXTENSION CORD. Make sure your

extension cord is in good condition. Use only a cord heavy

enough to carry the current your product will draw. An

undersized cord will cause a drop in line voltage result-

ing in loss of power and overheating. A wire gauge size

(A.W.G.) of at least 14 is recommended for an extension

cord 25 feet or less in length. If in doubt, use the next

heavier gauge. The smaller the gauge number, the heavier

the cord.

 DRESS PROPERLY. Do not wear loose clothing,

neckties, or jewelry that can get caught and draw you into

moving parts. Rubber gloves and nonskid footwear are

recommended when working outdoors. Also wear protec-

tive hair covering to contain long hair.

 ALWAYS WEAR SAFETY GLASSES WITH SIDE

SHIELDS. Everyday eyeglasses have only impact-

resistant lenses, they are NOT safety glasses.

 SECURE WORK. Use clamps or a vise to hold work

when practical, it is safer than using your hand and frees

both hands to operate the tool.

 DO NOT OVERREACH. Keep proper footing and

balance at all times.

 MAINTAIN TOOLS WITH CARE. Keep tools sharp

and clean for better and safer performance. Follow

instructions for lubricating and changing accessories.

 DISCONNECT TOOLS. When not in use, before

servicing, or when changing attachments, blades, bits,

cutters, etc., all tools should be disconnected from power

source.

 AVOID ACCIDENTAL STARTING. Be sure switch is off

when plugging in any tool.

 USE RECOMMENDED ACCESSORIES. Consult the

operator’s manual for recommended accessories. The

use of improper accessories may result in injury.

 NEVER STAND ON TOOL. Serious injury could occur if

the tool is tipped.

 CHECK DAMAGED PARTS. Before further use of the

tool, a guard or other part that is damaged should be

carefully checked to determine that it will operate properly

and perform its intended function. Check for alignment

of moving parts, binding of moving parts, breakage of

parts, mounting and any other conditions that may affect

its operation. A guard or other part that is damaged must

be properly repaired or replaced by an authorized service

center to avoid risk of personal injury.

 USE THE RIGHT DIRECTION OF FEED. Feed work into

a blade, cutter, or sanding spindle against the direction

or rotation of the blade, cutter, or sanding spindle only.

 NEVER LEAVE TOOL RUNNING UNATTENDED. TURN

THE POWER OFF. Don't leave tool until it comes to a

complete stop.

 PROTECT YOUR LUNGS. Wear a face or dust mask if

the cutting operation is dusty.

 PROTECT YOUR HEARING. Wear hearing protection

during extended periods of operation.

 DO NOT ABUSE CORD. Never carry tool by the cord or

yank it to disconnect from receptacle. Keep cord from

heat, oil, and sharp edges.

 USE OUTDOOR EXTENSION CORDS. When tool

is used outdoors, use only extension cords with

approved ground connection that are intended for use

outdoors and so marked.

KEEP BLADES CLEAN, SHARP, AND WITH

SUFFICIENT SET. Sharp blades minimize stalling

and kickback.

BLADE COASTS AFTER BEING TURNED OFF.

4 — English

GENERAL SAFETY RULES

 NEVER USE IN AN EXPLOSIVE ATMOSPHERE.

Normal sparking of the motor could ignite fumes.

 INSPECT TOOL CORDS PERIODICALLY. If

damaged, have repaired by a qualified service technician at

an authorized service facility. The conductor with insulation

having an outer surface that is green with or without yellow

stripes is the equipment-grounding conductor. If repair

or replacement of the electric cord or plug is necessary,

do not connect the equipment-grounding conductor to a

live terminal. Repair or replace a damaged or worn cord

immediately. Stay constantly aware of cord location and

keep it well away from the rotating blade.

 INSPECT EXTENSION CORDS PERIODICALLY and

replace if damaged.

 POLARIZED PLUGS. To reduce the risk of electric shock,

this tool has a polarized plug (one blade is wider than

the other). This plug will fit in a polarized outlet only one

way. If the plug does not fit fully in the outlet, reverse the

plug. If it still does not fit, contact a qualified electrician

to install the proper outlet. Do not change the plug in any

way.

 KEEP TOOL DRY, CLEAN, AND FREE FROM OIL AND

GREASE. Always use a clean cloth when cleaning. Never

use brake fluids, gasoline, petroleum-based products, or

any solvents to clean tool.

 STAY ALERT AND EXERCISE CONTROL. Watch what

you are doing and use common sense. Do not operate

tool when you are tired. Do not rush.

SPECIFIC SAFETY RULES

 FIRMLY CLAMP OR BOLT the tool to a workbench or

table at approximately hip height.

 KEEP HANDS AWAY FROM CUTTING AREA. Do not

reach underneath work or in blade cutting path with hands

and fingers for any reason. Always turn the power off.

 ALWAYS SUPPORT LONG WORKPIECES while cutting

to minimize risk of blade pinching and kickback. Saw may

slip, walk or slide while cutting long or heavy boards.

 ALWAYS USE A CLAMP to secure the workpiece when

possible.

 BE SURE THE BLADE CLEARS THE WORKPIECE.

Never start the saw with the blade touching the

workpiece. Allow motor to come up to full speed

before starting cut.

 DO NOT USE TOOL IF SWITCH DOES NOT TURN IT

ON AND OFF. Have defective switches replaced by an

authorized service center.

 USE ONLY CORRECT BLADES. Do not use blades with

incorrect size holes. Never use blade washers or blade

bolts that are defective or incorrect. The maximum blade

capacity of your saw is 10 in.

 BEFORE MAKING A CUT, BE SURE ALL ADJUST-

MENTS ARE SECURE.

 BE SURE BLADE PATH IS FREE OF NAILS. Inspect for

and remove all nails from lumber before cutting.

 NEVER TOUCH BLADE or other moving parts during

use.

NEVER START A TOOL WHEN ANY ROTATING COM-

PONENT IS IN CONTACT WITH THE WORKPIECE.

 DO NOT OPERATE A TOOL WHILE UNDER THE

INFLUENCE OF DRUGS, ALCOHOL, OR ANY

MEDICATION.

 WHEN SERVICING use only identical replacement parts.

Use of any other parts may create a hazard or cause

product damage.

 USE ONLY RECOMMENDED ACCESSORIES listed

in this manual or addendums. Use of accessories that

are not listed may cause the risk of personal injury.

Instructions for safe use of accessories are included

with the accessory.

 DOUBLE CHECK ALL SETUPS. Make sure blade is

tight and not making contact with saw or workpiece

before connecting to power supply.

 MAKE SURE THE MITER TABLE AND SAW ARM

(BEVEL FUNCTION) ARE LOCKED IN POSITION

BEFORE OPERATING YOUR SAW. Lock the miter

table by securely tightening the miter lock levers. Lock

the saw arm (bevel function) by securely tightening the

bevel lock lever.

 NEVER USE A LENGTH STOP ON THE FREE SCRAP

END OF A CLAMPED WORKPIECE. NEVER hold onto

or bind the free scrap end of the workpiece in any opera-

tion. If a work clamp and length stop are used together,

they must both be installed on the same side of the saw

table to prevent the saw from catching the loose end and

kicking up.

 NEVER cut more than one piece at a time. DO NOT

STACK more than one workpiece on the saw table at a

time.

5 — English

 NEVER PERFORM ANY OPERATION FREEHAND.

Always place the workpiece to be cut on the miter table

and position it firmly against the fence as a backstop.

Always use the fence.

 NEVER hand hold a workpiece that is too small to be

clamped. Keep hands clear of the cutting area.

 NEVER reach behind, under, or within three inches of the

blade and its cutting path with hands and fingers for any

reason.

 NEVER reach to pick up a workpiece, a piece of scrap,

or anything else that is in or near the cutting path of the

blade.

NEVER move the workpiece or make adjustment to any

cutting angle while the saw is running and the blade is

rotating. Any slip can result in contact with the blade

causing serious personal injury.

 AVOID AWKWARD OPERATIONS AND HAND

POSITIONS where a sudden slip could cause your

hand to move into the blade. ALWAYS make sure you

have good balance. NEVER operate the miter saw

on the floor or in a crouched position.

 NEVER stand or have any part of the body in line with

the path of the saw blade.

 ALWAYS release the power switch and allow the saw blade

to stop rotating before raising it out of the workpiece.

 DO NOT TURN THE MOTOR SWITCH ON AND OFF

RAPIDLY. This could cause the saw blade to loosen

and could create a hazard. Should this ever occur,

stand clear and allow the saw blade to come to a

complete stop. Disconnect your saw from the power

supply and securely retighten the blade bolt.

 IF ANY PART OF THIS MITER SAW IS MISSING or

should break, bend, or fail in any way, or should any

electrical component fail to perform properly, shut off

the power switch, remove the miter saw plug from the

power source and have damaged, missing, or failed parts

replaced before resuming operation.

 ALWAYS STAY ALERT! Do not allow familiarity (gained

from frequent use of the saw) to cause a careless

mistake. ALWAYS REMEMBER that a careless frac-

tion of a second is sufficient to inflict severe injury.

 IF THE POWER SUPPLY CORD IS DAMAGED, it must

be replaced only by the manufacturer or by an authorized

service center to avoid risk.

 MAKE SURE WORK AREA HAS AMPLE LIGHTING to

see the work and that no obstructions will interfere with

safe operation BEFORE performing any work using the

saw.

 ALWAYS TURN OFF THE SAW before disconnecting it

to avoid accidental starting when reconnecting to power

supply. NEVER leave the saw unattended while connected

to a power source.

 RELEASE THE SWITCH TRIGGER and allow the saw

blade to stop rotating before raising the blade out of

workpiece.

 THIS TOOL should have the following markings:

a) Wear eye protection.

b) Keep hands out of path of saw blade.

c) Do not operate saw without guards in place.

d) Do not perform any operation freehand.

e) Never reach around saw blade.

f) Turn off tool and wait for saw blade to stop before

moving workpiece or changing settings.

g) Disconnect power (or unplug tool as applicable)

before changing blade or servicing.

h) No load speed.

 ALWAYS MAKE SURE THE SAW BLADE HAS CLEAR-

ANCE OF ALL OBSTRUCTIONS BEFORE TURNING

THE SAW ON.

 MAKE SLIDING CUTS by pushing the saw blade down

on top of the workpiece then sliding it back toward the

rear of the saw. DO NOT pull the saw toward you while

making a cut.

 ALWAYS carry the tool only by the carrying handle.

 AVOID direct eye exposure when using the laser guide.

 THIS SAW CAN TIP OVER if the saw head is released

suddenly and the saw is not secured to a work sur-

face. ALWAYS secure this saw to a stable work sur-

face before any use to avoid serious personal injury.

 SAVE THESE INSTRUCTIONS. Refer to them

frequently and use to instruct other users. If you loan

someone this tool, loan them these instructions also.

SPECIFIC SAFETY RULES

6 — English

SYMBOLS

Some of the following symbols may be used on this tool. Please study them and learn their meaning. Proper

interpretation of these symbols will allow you to operate the tool better and safer.

Read Operator’s Manual

Safety Alert

No Hands Symbol

SYMBOL NAME DESIGNATION/EXPLANATION

Voltage

Time

Rotational speed, at no load

Double-insulated construction

Do not expose to rain or use in damp locations.

To reduce the risk of injury, user must read and understand opera-

tor’s manual before using this product.

Eye Protection

Precautions that involve your safety.

Failure to keep your hands away from the blade will result in

serious personal injury.

Wet Conditions Alert

Class II Construction

n

o

No Load Speed

min Minutes

V Volts

Always wear eye protection with side shields marked to comply

with ANSI Z87.1.

The following signal words and meanings are intended to explain the levels of risk associated with this product.

SYMBOL SIGNAL MEANING

DANGER:

Indicates an imminently hazardous situation, which, if not avoided, will result

in death or serious injury.

WARNING:

Indicates a potentially hazardous situation, which, if not avoided, could result

in death or serious injury.

CAUTION:

Indicates a potentially hazardous situation, which, if not avoided, may result in

minor or moderate injury.

NOTICE:

(Without Safety Alert Symbol) Indicates important information not related to an

injury hazard, such as a situation that may result in property damage.

Revolutions, strokes, surface speed, orbits etc., per minute

.../min

Per Minute

7 — English

ELECTRICAL

EXTENSION CORDS

When using a power tool at a considerable distance from

a power source, be sure to use an extension cord that has

the capacity to handle the current the tool will draw. An

undersized cord will cause a drop in line voltage, resulting in

overheating and loss of power. Use the chart to determine

the minimum wire size required in an extension cord. Only

round jacketed cords listed by Underwriter’s Laboratories

(UL) should be used.

When working outdoors with a tool, use an extension

cord that is designed for outside use. This type of cord is

designated with “WA” on the cord’s jacket.

Before using any extension cord, inspect it for loose or

exposed wires and cut or worn insulation.

**Ampere rating (on tool data plate)

0-2.0 2.1-3.4 3.5-5.0 5.1-7.0 7.1-12.0 12.1-16.0

Cord Length Wire Size (A.W.G.)

25' 16 16 16 16 14 14

50' 16 16 16 14 14 12

100' 16 16 14 12 10 —

**Used on 12 gauge - 20 amp circuit.

NOTE: AWG = American Wire Gauge

WARNING:

Keep the extension cord clear of the working area.

Position the cord so that it will not get caught on lumber,

tools or other obstructions while you are working with a

power tool. Failure to do so can result in serious personal

injury.

WARNING:

Check extension cords before each use. If damaged

replace immediately. Never use tool with a damaged cord

since touching the damaged area could cause electrical

shock resulting in serious injury.

DOUBLE INSULATION

Double insulation is a concept in safety in electric power

tools, which eliminates the need for the usual three-

wire grounded power cord. All exposed metal parts are

isolated from the internal metal motor components with

protecting insulation. Double insulated tools do not need

to be grounded.

WARNING:

The double insulated system is intended to protect

the user from shock resulting from a break in the tool’s

internal insulation. Observe all normal safety precautions

to avoid electrical shock.

NOTE: Servicing of a tool with double insulation requires

extreme care and knowledge of the system and should be

performed only by a qualified service technician. For service,

we suggest you return the tool to the nearest authorized

service center for repair. Always use original factory replace-

ment parts when servicing.

ELECTRICAL CONNECTION

This tool has a precision-built electric motor. It should be

connected to a power supply that is 120 volts, 60 Hz, AC

only (normal household current). Do not operate this tool

on direct current (DC). A substantial voltage drop will cause

a loss of power and the motor will overheat. If the tool does

not operate when plugged into an outlet, double-check the

power supply.

8 — English

GLOSSARY OF TERMS

Non-Through Cuts

Any cutting operation where the blade does not extend

completely through the thickness of the workpiece.

Push Blocks (for jointer planers)

Device used to feed the workpiece over the jointer planer

cutterhead during any operation. This aid helps keep the

operator’s hands well away from the cutterhead.

Push Blocks and Push Sticks (for table saws)

Devices used to feed the workpiece through the saw blade

during cutting operations. A push stick (not a push block)

should be used for narrow ripping operations. These aids

help keep the operator’s hands well away from the blade.

Pilot Hole (drill presses)

A small hole drilled in a workpiece that serves as a guide for

drilling large holes accurately.

Resaw

A cutting operation to reduce the thickness of the workpiece

to make thinner pieces.

Resin

A sticky, sap-based substance that has hardened.

Revolutions Per Minute (RPM)

The number of turns completed by a spinning object in one

minute.

Ripping or Rip Cut

A cutting operation along the length of the workpiece.

Riving Knife/Spreader/Splitter (table saws)

A metal piece, slightly thinner than the blade, which helps

keep the kerf open and also helps to prevent kickback.

Saw Blade Path

The area over, under, behind, or in front of the blade. As it

applies to the workpiece, that area which will be or has been

cut by the blade.

Set

The distance that the tip of the saw blade tooth is bent (or

set) outward from the face of the blade.

Snipe (planers)

Depression made at either end of a workpiece by cutter

blades when the workpiece is not properly supported.

Through Sawing

Any cutting operation where the blade extends completely

through the thickness of the workpiece.

Throw-Back

The throwing back of a workpiece usually caused by the

workpiece being dropped into the blade or being placed

inadvertently in contact with the blade.

Workpiece or Material

The item on which the operation is being done.

Worktable

Surface where the workpiece rests while performing a

cutting, drilling, planing, or sanding operation.

Anti-Kickback Pawls (radial arm and table saws)

A device which, when properly installed and maintained,

is designed to stop the workpiece from being kicked back

toward the front of the saw during a ripping operation.

Arbor

The shaft on which a blade or cutting tool is mounted.

Bevel Cut

A cutting operation made with the blade at any angle other

than 90° to the table surface.

Chamfer

A cut removing a wedge from a block so the end (or part of

the end) is angled rather than at 90°.

Compound Cut

A cross cut made with both a miter and a bevel angle.

Cross Cut

A cutting or shaping operation made across the grain or the

width of the workpiece.

Cutter Head (planers and jointer planers)

A rotating cutterhead with adjustable blades or knives. The

blades or knives remove material from the workpiece.

Dado Cut

A non-through cut which produces a square-sided notch or

trough in the workpiece (requires a special blade).

Featherboard

A device used to help control the workpiece by guiding

it securely against the table or fence during any ripping

operation.

FPM or SPM

Feet per minute (or strokes per minute), used in reference

to blade movement.

Freehand

Performing a cut without the workpiece being guided by a

fence, miter gauge, or other aids.

Gum

A sticky, sap-based residue from wood products.

Heel

Alignment of the blade to the fence.

Kerf

The material removed by the blade in a through cut or the

slot produced by the blade in a non-through or partial cut.

Kickback

A hazard that can occur when the blade binds or stalls,

throwing the workpiece back toward operator.

Leading End

The end of the workpiece pushed into the tool first.

Miter Cut

A cutting operation made with the workpiece at any angle

to the blade other than 90°.

9 — English

FEATURES

Fig. 1 and 2

PRODUCT SPECIFICATIONS

Blade Arbor .............................................................. 5/8 in.

Blade Diameter .......................................................... 10 in.

No Load Speed ....................................5,000 r/min. (RPM)

Input ....................................... 120 V, AC only, 60 Hz, 13 A

Cutting Capacity with Miter at 0°/Bevel 0°:

Maximum nominal lumber sizes: ............................2 x 12

Cutting Capacity with Miter at 45°/Bevel 0°:

Maximum nominal lumber sizes: ..............................2 x 8

Cutting Capacity with Miter at 0°/Bevel 45°:

Maximum nominal lumber sizes: ............................2 x 12

Cutting Capacity with Miter at 45°/Bevel 45°:

Maximum nominal lumber sizes: ..............................2 x 8

SWITCH

TRIGGER

BEVEL

SCALE

DUST

BAG

BEVEL

LOCK

LEVER

MITER FENCE

TABLE

EXTENSION

BASE

WORK

CLAMP

MITER

TABLE

CONTROL

ARM

MITER

LOCK

HANDLE

THROAT

PLATE

“NO HANDS

ZONE” LABEL

“NO HANDS ZONE”

BOUNDARY LINE

MITER

SCALE

UPPER BLADE

GUARD

LOWER BLADE

GUARD

“D”

HANDLE

SLIDE LOCK

KNOB

SLIDE

BAR

HEIGHT

ADJUSTMENT

KNOB

SUPPORT

FOOT

10 — English

FEATURES

KNOW YOUR COMPOUND MITER SAW

See Figures 1 and 2.

The safe use of this product requires an understanding of

the information on the tool and in this operator’s manual as

well as a knowledge of the project you are attempting. Before

use of this product, familiarize yourself with all operating

features and safety rules.

10 in. BLADE

A 10 in. blade is included with the compound miter saw. It

will cut materials up to 4 in. thick or 6 in. wide, depending

upon the angle at which the cut is being made.

13 AMP MOTOR

The saw has a powerful 13 amp motor with sufficient power

to handle tough cutting jobs. It is made with all ball bearings,

and has externally accessible brushes for ease of servicing.

BEVEL LOCK LEVER

The bevel lock lever securely locks your compound miter

saw at desired bevel angles. The bevel lock lever is spring

loaded and is released by pulling the lever away from the

saw housing and ratcheting the lever.

CARRYING HANDLE

See Figure 3.

For convenience when carrying or transporting the miter

saw from one place to another, a carrying handle has been

provided on top of the saw arm. To transport, turn off and

unplug the saw, then lower the saw arm and lock it in the

down position by pulling the lock pin away from the saw

housing and rotating it until it clicks into the slot.

ELECTRIC BRAKE

An electric brake has been provided to quickly stop blade

rotation after the switch is released.

LASER GUIDE

For more accurate cuts, a laser guide is included with the

miter saw. When used properly, the laser guide makes

accurate, precision cutting simple and easy.

MITER FENCE

The miter fence on the compound miter saw has been

provided to hold your workpiece securely against when

making all cuts. The left side is larger providing additional

support.

MITER LOCK HANDLE

See Figure 3.

The miter lock handle securely locks the saw at desired

miter angles.

SAW ARM LOCKED IN DOWN POSITION

LOCK

MITER LOCK

HANDLE

SAW

ARM

CARRYING

HANDLE

Fig. 3

MITER SCALE

The miter scale has index points provided at 0°, 15°, 22.5°,

31.6°, 45°, and 60.°

POSITIVE STOPS ON MITER TABLE

Positive stops have been provided at 0°, 15°, 22.5°, 30°, and

45° on both the left and right side of the miter table.

SELF-RETRACTING LOWER BLADE GUARD

The lower blade guard is made of shock-resistant, see-through

plastic that provides protection from each side of the blade.

It retracts over the upper blade guard as the saw is lowered

into the workpiece.

SLIDE BAR

When unlocked, the saw arm will glide forward and backward

the length of the slide bar for cutting various workpiece widths.

SLIDE LOCK KNOB

The slide lock knob locks and unlocks the sliding feature

of this tool.

11 — English

FEATURES

The following tools (not included) are needed for making adjustments or installing the blade:

TOOLS NEEDED

Fig. 6

COMBINATION

SQUARE

FRAMING SQUARE

COMBINATION WRENCHES (2)

(10 mm, 12 mm)

HEX KEYS (3)

(3 mm, 5 mm, 6 mm)

Fig. 4

Fig. 5

PADLOCK

SWITCH

TRIGGER

SWITCH

TRIGGER

SPINDLE

LOCK BUTTON

PHILLIPS SCREWDRIVER

SPINDLE LOCK BUTTON

See Figure 4.

The spindle lock button locks the spindle and stops the

blade from rotating. Depress and hold the lock button while

installing, changing, or removing blade.

SWITCH TRIGGER

See Figure 5.

To prevent unauthorized use of the compound miter saw,

disconnect it from the power supply and lock the switch in

the off position. To lock the switch, install a padlock (not

included) through the hole in the switch trigger. A lock with

a long shackle up to 9/32 in. diameter may be used. When

the lock is installed and locked, the switch is inoperable.

Store the padlock key in another location.

12 — English

LOOSE PARTS LIST

Fig. 7

WARNING:

The use of attachments or accessories not listed might be hazardous and could cause serious personal injury.

 Blade Wrench

 Blade

 Operator’s Manual

TABLE

EXTENSION

WORK

CLAMP

DUST

BAG

TABLE

EXTENSION

BLADE

The following items are included with your Compound Miter Saw:

 Dust Bag

 Table Extensions (2)

 Work Clamp

BLADE

WRENCH

13 — English

ASSEMBLY

TRACE HOLES

AT THESE LOCATIONS

FOR HOLE PATTERN

Fig. 8

MOUNTING

SURFACE

SAW BASE

TRACE HOLES

AT THESE LOCATIONS

FOR HOLE PATTERN

WARNING:

Do not connect to power supply until assembly is

complete. Failure to comply could result in accidental start-

ing and possible serious personal injury.

WARNING:

Do not start the compound miter saw without checking for

interference between the blade and the miter fence. Damage

could result to the blade if it strikes the miter fence during

operation of the saw.

WARNING:

This saw can tip over if the saw head is released suddenly

and the saw is not secured to a work surface. ALWAYS

secure this saw to a stable work surface before any use to

avoid serious personal injury.

MOUNTING HOLES

See Figure 8.

WARNING:

Always make sure the compound miter saw is securely

mounted to a workbench or an approved workstand.

Failure to heed this warning can result in serious

personal injury.

The compound miter saw should be mounted to a firm sup-

porting surface such as a workbench. Four bolt holes have

been provided in the saw base for this purpose. Each of the

four mounting holes should be bolted securely using 3/8 in.

machine bolts, lock washers, and hex nuts (not included). Bolts

should be of sufficient length to accommodate the saw base,

lock washers, hex nuts, and the thickness of the workbench.

Tighten all four bolts securely.

The hole pattern for mounting to a workbench is shown in fig-

ure 8. Carefully check the workbench after mounting to make

sure that no movement can occur during use. If any tipping,

sliding, or walking is noted, secure the workbench to the floor

before operating.

UNPACKING

This product requires assembly.

 Carefully lift saw from the carton by the carrying handle and

the saw base, and place it on a level work surface.

WARNING:

Do not use this product if any parts on the Loose Parts List

are already assembled to your product when you unpack

it. Parts on this list are not assembled to the product by the

manufacturer and require customer installation. Use of a

product that may have been improperly assembled could

result in serious personal injury.

 This saw has been shipped with the saw arm secured in the

down position. To release the saw arm, push down on the top

of the saw arm, cut the tie-wrap, and pull out on the lock pin.

 Lift the saw arm by the handle. Hand pressure should

remain on the saw arm to prevent sudden rise upon

release of the tie wrap.

 Inspect the tool carefully to make sure no breakage or dam-

age occurred during shipping.

 Do not discard the packing material until you have carefully

inspected and satisfactorily operated the tool.

 The saw is factory set for accurate cutting. After

assembling it, check for accuracy. If shipping has

influenced the settings, refer to specific procedures

explained in this manual.

 If any parts are damaged or missing, please call

1-800-525-2579 for assistance.

WARNING:

If any parts are damaged or missing do not operate this tool

until the parts are replaced. Failure to heed this warning

could result in serious personal injury.

WARNING:

Do not attempt to modify this tool or create accessories not

recommended for use with this tool. Any such alteration or

modification is misuse and could result in a hazardous condi-

tion leading to possible serious personal injury.

14 — English

ASSEMBLY

NOTE: Many of the illustrations in this manual show only

portions of the compound miter saw. This is intentional

so that we can clearly show points being made in the

illustrations. Never operate the saw without all guards

securely in place and in good operating condition.

LOCKING / UNLOCKING THE SAW ARM

See Figure 9.

To unlock and raise the saw arm:

 Firmly grasp the “D” handle and apply downward

pressure while at the same time pulling the lock pin out

and away from the saw housing. Rotate lock pin 90º to

lock (or unlock) the saw arm.

 Release the lock pin and slowly raise the saw arm.

To lock the saw arm:

 Firmly grasp the “D” handle and apply downward

pressure while at the same time pulling the lock pin out

and away from the saw housing.

 Release the lock pin allowing it to lock the saw into place.

DUST BAG

See Figure 10.

A dust bag is provided for use on this miter saw. It fits over

the exhaust port on the upper blade guard.

NOTE: the exhaust port also accepts 1-1/4 in. vacuum hose.

To install:

 Squeeze the two metal clips to open the mouth of the

bag and slide it on the exhaust port.

 Release the clips. The metal ring in the bag should lock

in between the grooves on the exhaust port.

To remove the dust bag for emptying:

 Reverse the above procedure.

Fig. 9

LOCK

“D”

HANDLE

Fig. 10

DUST

BAG

EXHAUST

PORT

15 — English

ASSEMBLY

WORK CLAMP

See Figure 11.

WARNING:

In some operations, the work clamp assembly may

interfere with the operation of the blade guard assembly.

Always make sure there is no interference with the blade

guard prior to beginning any cutting operation to reduce

the risk of serious personal injury.

The work clamp provides greater control by clamping the

workpiece to the saw table. It also prevents the workpiece

from creeping toward the saw blade. This is very helpful

when cutting compound miters. Depending on the cutting

operation and the size of the workpiece, it may be necessary

to use a C-clamp instead of the work clamp to secure the

workpiece prior to making the cut.

To install the work clamp:

 Place the work clamp shaft in either the left or right hole

located behind the miter fence.

 Rotate the height adjustment knob on the work clamp to

move the shaft up or down as needed. When the workpiece

is secure, tighten both the work shaft lock and the work

clamp knob.

TABLE EXTENSIONS

See Figures 12 - 13.

To install table extensions, insert the ends of extensions into

the holes in the sides of the base. Adjust the extensions to

the desired length.

To secure table extensions:

 Loosen lock nut.

 Tighten table extension screw securing the table extension.

 Retighen lock nut.

 Repeat for other extension.

Fig. 11

BASE

HEIGHT

ADJUSTMENT

KNOB

Fig. 12

Fig. 13

SAW VIEWED FROM BOTTOM

TABLE

EXTENSION

BASE

TABLE

EXTENSION

WORK

CLAMP

TABLE EXTENSION

SCREW

LOCK NUT

WORK

CLAMP

KNOB

16 — English

ASSEMBLY

TO INSTALL / REPLACE THE BLADE

See Figures 14 - 15.

WARNING:

A 10 in. blade is the maximum blade capacity of the saw.

Never use a blade that is too thick to allow outer blade

washer to engage with the flats on the spindle. Larger

blades will come in contact with the blade guards, while

thicker blades will prevent the blade bolt from secur-

ing the blade on the spindle. Either of these situations

could result in a serious accident and can cause serious

personal injury.

 Unplug the saw.

 Remove screws. Rotate lower blade guard and blade bolt

cover up and back to expose the blade bolt.

 Depress the spindle lock button and rotate the blade bolt

until the spindle locks.

 Using the wrench provided, loosen and remove the blade

bolt.

NOTE: The blade bolt has left hand threads. Turn blade

bolt clockwise to loosen.

 Remove the flat washer and the outer blade washer. Do

not remove the inner blade washer.

 Wipe a drop of oil onto inner blade washer and outer

blade washer where they contact the blade.

WARNING:

If inner blade washer has been removed, replace it before

placing blade on spindle. Failure to do so could cause an

accident since blade will not tighten properly.

 Fit saw blade inside lower blade guard and onto spindle.

The blade teeth point downward at the front of saw as

shown in figure 15.

 Replace the outer blade washer and the flat washer.

Double “D” flats on blade washers align with flats on

spindle.

 Depress spindle lock button and replace blade bolt.

NOTE: The blade bolt has left hand threads. Turn blade bolt

counterclockwise to tighten.

CAUTION:

Always install the blade with the blade teeth and the

arrow printed on the side of the blade pointing down at

the front of the saw. The direction of blade rotation is

also stamped with an arrow on the upper blade guard.

 Tighten blade bolt securely.

 Replace the lower blade guard and blade bolt cover.

 Replace screws and tighten securely.

Fig. 15

LOWER

BLADE

GUARD

BLADE

OUTER BLADE

WASHER

WITH DOUBLE

“D” FLATS

BLADE

BOLT

TO

TIGHTEN

TO

LOOSEN

SCREWS

FLAT(S)

ON SPINDLE

BLADE

BOLT

COVER

SPINDLE LOCK

BUTTON

Fig. 14

INNER BLADE

WASHER WITH

DOUBLE “D”

FLATS

NOTE: BEFORE USE,

REPLACE SCREWS AND

TIGHTEN SECURELY

TO PREVENT GUARD

MOVEMENT

BLADE

BOLT

OUTER

BLADE

WASHER

BLADE

INNER

BLADE

WASHER

FLAT

WASHER

17 — English

ASSEMBLY

WARNING:

Make sure the spindle lock button is not engaged

before reconnecting saw into power source. Never

engage spindle lock button when blade is rotating.

DANGER:

Laser radiation. Avoid direct eye contact with light source.

WARNING:

Use of controls or adjustments or performance of

procedures other than those specified herein may result

in hazardous radiation exposure.

ALIGNING THE LASER GUIDE LINE

See Figure 16.

Lock the switch by installing a padlock (not included) through

the hole in the switch trigger and closing the shackle.

Draw a line on the workpiece. When the laser guide switch

is turned on it will generate a red line on the work surface.

This line will let you see your mark and the laser guide line

at the same time, and will assist you in lining up the mark

for more accurate cutting of the workpiece.

Align the laser line and the mark with the blade at the

uppermost position. Once both lines are in alignment, do

not move the workpiece.

Remove the padlock then plug the saw into the power

source. Make several practice cuts on different styles and

thickness of material. Repeat the steps above as necessary.

Follow the directions below for using the laser guide:

Removing Your Mark:

Position the laser line near the left edge of your mark on the

work surface in order to remove the mark.

To Cut Your Mark:

Position the laser line near or over your mark on the work

surface in order to cut the mark.

To Leave Your Mark:

Position the laser line near the right edge of your mark on

the work surface in order to leave the mark.

After you have become familiar with using the laser guide,

you will be able to remove, cut, or leave your mark on the

work surface. Practice will teach you the correct position for

aligning the laser line with your mark.

Fig. 16

RED

LINE

LASER

GUIDE

SWITCH

LASER RADIATION EMITTED

FROM THIS APERTURE

LOCK TRIGGER PRIOR

TO ADJUSTING LASER

AVOID EXPOSURE:

18 — English

ASSEMBLY

REMOVING / REPLACING THE THROAT PLATE

See Figure 17.

WARNING:

The throat plate must be below the saw table. If the throat

plate is too high or too low, the workpiece can catch on

the uneven edges resulting in binding which could result

in serious personal injury.

Never operate the saw without a throat plate installed.

To remove / replace:

 Unplug the saw.

 Remove the screws securing the right side of the zero

clearance throat plate.

 Lift the throat plate from the saw. Repeat the above steps

for the left side of the throat plate.

 To reinstall the throat plate, align the holes in the throat

plate with the holes in the saw base.

 Retighten the screws, being careful not to overtighten

which can cause the throat plate to bow or bend.

ADJUSTING SUPPORT FOOT

See Figure 17.

When making sliding cuts, turn the support foot clockwise

or counterclockwise depending on the amount of support

needed.

THROAT

PLATE

Fig. 17

SUPPORT

FOOT

19 — English

ASSEMBLY

SQUARING THE BLADE TO THE FENCE

See Figures 18 - 21.

 Unplug the saw.

 Pull the saw arm all the way down and engage the lock

pin to hold the saw arm in transport position.

 Loosen the miter lock handle approximately one-half turn.

 Rotate the miter table until the pointer on the control arm

is positioned at 0°.

 Securely tighten the miter lock handle.

 Lay a framing square flat on the miter table. Place one

leg of the square against the fence. Slide the other leg

of the square against the flat part of saw blade.

NOTE: Make sure that the square contacts the flat part

of the saw blade, not the blade teeth.

 The edge of the square and the saw blade should be

parallel as shown in figure 19.

 If the front or back edge of the saw blade angles away

from the square as shown in figures 20 - 21, adjustments

are needed.

 Loosen the socket head screws that secure the miter

fence to the miter table.

 Rotate the miter fence left or right until the saw blade is

parallel with the square.

 Retighten the screws securely and recheck the blade-to-

fence alignment.

The saw has two scale indicators, one on the bevel scale

and one on the miter scale. After squaring adjustments have

been made, it may be necessary to loosen the indicators

screws and reset them to zero.

MITER

LOCK HANDLE

Fig. 19

MITER

TABLE

VIEW OF BLADE SQUARE WITH FENCE

BLADE

FRAMING

SQUARE

VIEW OF BLADE NOT SQUARE WITH

FENCE, ADJUSTMENTS ARE REQUIRED

Fig. 20

Fig. 18

FENCE

SOCKET HEAD

SCREW(S)

SOCKET HEAD

SCREW(S)

Fig. 21

VIEW OF BLADE NOT SQUARE WITH

FENCE, ADJUSTMENTS ARE REQUIRED

MITER

FENCE

MITER

TABLE

BLADE

FRAMING

SQUARE

MITER

FENCE

MITER

TABLE

BLADE

FRAMING

SQUARE

MITER

FENCE

20 — English

MITER

TABLE

COMBINATION

SQUARE

BLADE

MITER

FENCE

ASSEMBLY

SCALE

INDICATOR

Fig. 22

INDICATOR

SCREW

BEVEL

SCALE

SQUARING THE BLADE TO THE MITER TABLE

See Figures 22 - 25.

 Unplug the saw.

 Pull the saw arm all the way down and engage the lock

pin to hold the saw arm in transport position.

 Loosen the miter lock handle approximately one-half turn.

 Rotate the miter table until the pointer on the control arm

is positioned at 0°. Securely tighten the miter lock handle.

 Loosen the bevel lock lever and set saw arm at 0° bevel

(blade set 90° to miter table). Tighten bevel lock lever.

 Place a combination square against the miter table and

the flat part of saw blade.

NOTE: Make sure that the square contacts the flat part

of the saw blade, not the blade teeth.

 Rotate the blade by hand and check the blade-to-table

alignment at several points.

 The edge of the square and the saw blade should be

parallel as shown in figure 23.

 If the top or bottom of the saw blade angles away from

the square as shown in figures 24 and 25, adjustments

are needed.

 Loosen the lock nut securing positive stop adjustment

screw. Also loosen bevel lock lever.

 Adjust positive stop adjustment screw to bring saw

blade into alignment with the square. See Positive Stop

Adjustment in the Adjustment section.

 Retighten bevel lock lever. Next, retighten lock nut

securing the positive stop adjustment screw. Recheck

blade-to-table alignment.

NOTE: The above procedure can be used to check blade

squareness of the saw blade to the miter table at both 0°

and 45° angles.

The saw has two scale indicators, one on the bevel scale

and one on the miter scale. After squaring adjustments have

been made, it may be necessary to loosen the indicator

screws and reset them to zero.

Fig. 23

CORRECT VIEW OF BLADE

SQUARE WITH MITER TABLE

VIEW OF BLADE NOT SQUARE WITH MITER TABLE,

ADJUSTMENTS ARE REQUIRED

Fig. 24

Fig. 25

VIEW OF BLADE NOT SQUARE WITH MITER TABLE,

ADJUSTMENTS ARE REQUIRED

MITER

TABLE

COMBINATION

SQUARE

BLADE

MITER

FENCE

POSITIVE STOP

ADJUSTMENT

SCREW

LOCK

NUT(S)

MITER

TABLE

MITER

LOCK HANDLE

COMBINATION

SQUARE

BLADE

MITER

FENCE

La page charge ...

Ryobi tss100l1 Manuel utilisateur

Ryobi tss100l1 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents