JVC Everio GZ-MG255U Instructions Manual

Catégorie
Caméscopes
Taper
Instructions Manual

Ce manuel convient également à

ENGLISH
FRANÇAIS
EN FR
INSTRUCTIONS
MANUEL D’UTILISATION
HARD DISK CAMCORDER
CAMÉSCOPE À DISQUE DUR
GZ-MG255U
GZ-MG155U
GZ-MG130U
Dear Customer
Thank you for purchasing
this hard disk camera. Before
use, please read the safety
information and precautions
contained in pages 2 and 3 to
ensure safe use of this product.
For Future Reference:
Enter the Model No. (located on
the bottom of the camera) and
Serial No. (located on the battery
pack mount of the camera)
below.
Model No.
Serial No.
Cher client,
Nous vous remercions d’avoir
acheté cet appareil photo à
disque dur. Avant utilisation,
veuillez lire les informations
et les précautions de sécurité
présentées dans les pages 2 et 3
pour utiliser cet appareil en toute
sécurité.
Pour consultation ultérieure :
Noter ci-dessous le N° de
modèle (fi gurant sous l’appareil
photo) et le N° de série (fi gurant
sur le logement de la batterie de
l’appareil photo).
N° de modèle
N° de série
The camera illustrations appearing in this
instruction manual are of the GZ-MG130.
Les illustrations de l’appareil photo qui apparaît
dans ce manuel d’instructions sont celles du
modèle GZ-MG130.
2
Safety Precautions
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an
equilateral triangle, is intended to alert the user to the
presence of uninsulated "dangerous voltage" within the
product's enclosure that may be of sufficient magnitude
to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is
intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in
the literature accompanying the appliance.
WARNING: TO PREVENT FIRE OR
SHOCK HAZARD, DO NOT EXPOSE THIS
UNIT TO RAIN OR MOISTURE.
NOTES:
The rating plate and safety caution are on the
bottom and/or the back of the main unit.
The serial number plate is on the battery pack
mount.
The rating information and safety caution of the
AC adapter are on its upper and lower sides.
Caution on Replaceable lithium battery
The battery used in this device may present a fi re
or chemical burn hazard if mistreated.
Do not recharge, disassemble, heat above 100°C
or incinerate.
Replace battery with Panasonic (Matsushita
Electric), Sanyo, Sony or Maxell CR2025.
Danger of explosion or Risk of fi re if the battery is
incorrectly replaced.
Dispose of used battery promptly.
Keep away from children.
Do not disassemble and do not dispose of in
re.
For USA-California Only
This product contains a CR Coin Cell Lithium
Battery which contains Perchlorate Material
– special handling may apply.
See www.dtsc.ca.gov/hazardouswaste/perchlorate
When the equipment is installed in a cabinet or on
a shelf, make sure that it has suffi cient space on
all sides to allow for ventilation (10 cm (3-15/16
)
or more on both sides, on top and at the rear).
Do not block the ventilation holes.
(If the ventilation holes are blocked by a
newspaper, or cloth etc. the heat may not be able
to get out.)
No naked fl ame sources, such as lighted candles,
should be placed on the apparatus.
When discarding batteries, environmental
problems must be considered and the local rules
or laws governing the disposal of these batteries
must be followed strictly.
The apparatus shall not be exposed to dripping
or splashing.
Do not use this equipment in a bathroom or
places with water.
Also do not place any containers fi lled with water
or liquids (such as cosmetics or medicines, fl ower
vases, potted plants, cups etc.) on top of this unit.
(If water or liquid is allowed to enter this
equipment, fi re or electric shock may be caused.)
Do not point the lens directly into the sun. This
can cause eye injuries, as well as lead to the
malfunctioning of internal circuitry. There is also a
risk of fi re or electric shock.
CAUTION!
The following notes concern possible physical
damage to the camera and to the user.
Carrying or holding the camera by the LCD monitor
can result in dropping the unit, or in a malfunction.
Do not use a tripod on unsteady or unlevel surfaces.
It could tip over, causing serious damage to the
camera.
CAUTION!
Connecting cables (Audio/Video, S-Video, etc.)
to the camera and leaving it on top of the TV is
not recommended, as tripping on the cables will
cause the camera to fall, resulting in damage.
CAUTION:
The mains plug shall remain readily operable.
WARNING:
Batteries shall not be exposed to excessive heat
such as direct sunshine, fi re or the like.
3
ENGLISH
IMPORTANT SAFETY INSTRUCTIONS
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install
in accordance with the manufacturer’s instruc-
tions.
8. Do not install near any heat sources such
as radiators, heat registers, stoves, or other
apparatus (including amplifi ers) that produce
heat.
9. Only use attachments/accessories specifi ed by
the manufacturer.
10. Use only with the cart,
stand, tripod, bracket,
or table specifi ed by
the manufacturer,
or sold with the ap-
paratus. When a cart
is used, use caution
when moving the
cart/apparatus combination to avoid injury from
tip-over.
11. Unplug this apparatus during lightning storms
or when unused for long periods of time.
12. Refer all servicing to qualifi ed service person-
nel. Servicing is required when the apparatus
has been damaged in any way, such as
power-supply cord or plug is damaged, liquid
has been spilled or objects have fallen into the
apparatus, the apparatus has been exposed to
rain or moisture, does not operate normally, or
has been dropped.
Remember that this camera is intended for
private consumer use only.
Any commercial use without proper permission
is prohibited. (Even if you record an event such
as a show, performance or exhibition for personal
enjoyment, it is strongly recommended that you
obtain permission beforehand.)
Trademarks
Manufactured under license from Dolby
Laboratories. Dolby and double-D symbol are
trademarks of Dolby Laboratories.
MascotCapsule is a registered trademark of HI
CORPORATION in Japan.
Copyright © 2001 HI CORPORATION. All rights
reserved.
Other product and company names included
in this instruction manual are trademarks
and/or registered trademarks of their respective
holders.
4
Read This First!
Make a backup of important recorded data
JVC will not be responsible for any lost data. It is recommended to copy your important
recorded data to a DVD or other recording media for storage. ( pg. 40)
Make a trial recording
Before the actual recording of important data, make a trial recording and play back the
recorded data to check that the video and sound have been recorded correctly.
Reset the camera if it does not operate correctly
This camera uses a microcomputer. Factors such as background noise and interference
can prevent it from operating correctly. If the camera does not operate correctly, reset
the camera. ( pg. 51)
Precautions on handling batteries
Be sure to use the JVC BN-VF808U/VF815U/VF823U battery packs.
If the camera is subjected to electrostatic discharge, turn the power off before using it
again.
If a malfunction occurs, stop using the camera immediately
and consult your local JVC dealer
If a problem occurs when using the SD card, take the card together with the camera
for repair. If one of them is not included, the cause of the malfunction cannot be
diagnosed, and the camera cannot be repaired.
Recorded data may be erased while the camera is being repaired or inspected. Back
up all data before requesting repairs or inspections.
Because the camera may be used for demonstration in a
shop, the demonstration mode is set to on by default
To deactivate the demonstration mode, set [DEMO MODE] to [OFF]. ( pg. 48)
This operating instruction is applicable to models
GZ-MG255, GZ-MG155 and GZ-MG130
Unless otherwise indicated, illustrations in this operating instructions are of
GZ-MG130.
Icons such as indicate that the feature is applicable to the specifi ed model only.
When connecting the camera to other device
using a DV cable, make sure to follow the procedure below.
Connecting the cable incorrectly may cause malfunctions to
the camera and/or other device.
Connect the DV cable fi rst to other device, and then to the camera.
Connect the DV cable (plugs) correctly according to the shape of the DV connector.
5
ENGLISH
GETTING STARTED
Accessories ............................................ 6
How to Use the Everio Dock .........................6
Attaching the Shoulder Strap ........................7
Preparing the Remote Control ....................... 7
Index ........................................................ 8
Indications on LCD Monitor ................ 10
Necessary Settings before Use .......... 12
Charging the Battery Pack ..........................12
Language Setting ....................................... 13
Date/Time Setting ....................................... 13
Other Settings ...................................... 14
Grip Adjustment .......................................... 14
Lens Cover .................................................14
Checking the Remaining Battery Power .....14
Tripod Mounting .......................................... 14
When Using an SD Card ............................15
RECORDING
Recording Files ..................................... 16
Video Recording .........................................16
Still Image Recording .................................17
Zooming ......................................................18
LED Light .................................................... 18
Flash ........................................................... 18
Registering Files to Events ......................... 19
Checking the Remaining Space on the
Recording Media ........................................ 19
Manual Recording ............................... 20
To Change to Manual Recording Mode ...... 20
Program AE ................................................20
Nightalive .................................................... 21
Backlight Compensation ............................. 21
Spot Exposure Control ............................... 21
Manual Setting in Function Menu ...............22
PLAYBACK
Playing Back Files ................................ 24
Video Playback ...........................................24
Still Image Playback ...................................25
File Search Function ...................................26
To Play Back Demonstration Files
................. 27
Playback with Special Effects .....................28
Watching Images on TV ....................... 29
EDITING/PRINTING
Managing Files ..................................... 30
Deleting/Protecting Files .............................30
Viewing File Information .............................32
Changing the Event Registration of
Video Files after Recording ........................32
Partial Delete (EDITED COPY) ...................33
Playlists ................................................ 34
Creating Playlists ........................................ 34
Playing Back Playlists .................................35
Other Operations of Playlists ......................36
Print Setting ......................................... 37
DPOF Print Setting .....................................37
Direct Printing with PictBridge Printer ........38
COPYING
Copying Files ....................................... 40
Using a DVD Burner to Copy Files from
the Camera (DVD Creation Function) .........40
Using a VCR/DVD Recorder to Dub
Files from the Camera .................................44
Using the Camera to Dub Files from a VCR/
DVD Player .................................................. 44
Copying/Moving Still Image Files ................45
MENU SETTINGS
Changing the Menu Settings .............. 46
FURTHER INFORMATION
Troubleshooting ................................... 51
Warning Indications ............................ 54
Cleaning ............................................... 55
Specifi cations ...................................... 55
Cautions ............................................... 58
Terms ................................................... 60
Contents
6
Accessories
Everio Dock
CU-VC3U (below)
AC Adapter
AP-V18U/14U
Battery Pack
BN-VF808U
Audio/Video Cable
USB Cable
(pg. 38, 40 and
PC OPERATION
GUIDE)
Shoulder Strap
(pg. 7)
CD-ROM
( PC OPERATION
GUIDE)
Remote Control Unit
RM-V750U (pg. 7)
NOTE
Make sure to use the provided cables for
connections. Do not use any other cables.
Lithium Battery
CR2025
Pre-installed in the
remote control unit.
How to Use the Everio Dock
You can connect cables to the connectors of the Everio dock. The connection is completed when
you place the camera on the dock.
NOTE
For the connection using the S connector and DV Connector, an optional S-Video cable and DV cable
are needed. To purchase these cables, consult the JVC Service Center described on the sheet included
in the package for details on its availability. Make sure to connect the end with a core fi lter to the
camera. The core fi lter reduces interference.
The S-Video cable (optional) enables even higher quality playback on TV. (pg. 29) Be sure to use
the YTU94146A S-Video cable.
When dubbing fi les from the camera using a VCR/DVD recorder (pg. 44), using the DV cable
enables even higher quality dubbing. Be sure to use the VC-VDV204U DV cable. Operation using the
DV cable is not guaranteed on all of the devices.
Camera
Connection
Terminal
S Connector
AV Connector
DC Connector
DV Connector
USB
Connector
7
ENGLISH
Attaching the Shoulder Strap
Peel off the pad and thread
the end of the strap through
the eyelet.
Thread the strap through the
buckle, adjust its length, and
use the strap guide to fi x it
in place.
Position the buckle near the
eyelet and reattach the pad.
Preparing the Remote Control
A battery is included inside the remote control at the time of purchase.
Remove the insulation sheet before use.
Beam Effective Area
NOTE
The transmitted beam may not be effective
or may cause incorrect operation when the
remote sensor is directly exposed to sunlight
or powerful lighting.
To Reinsert the Battery
Pull out the battery holder by pressing the
lock tab.
Eyelet
Strap Guide
Buckle
Effective distance:
5 m (16 ft)
Remote Sensor
Lock Tab
Lithium Battery
(CR2025)
8
Index
NOTES
The LCD monitor can rotate 270°.
Power-linked operation
You can also turn the camera on/off by
opening/closing the LCD monitor during the
recording mode.
Be careful not to cover , , and
during shooting.
9
ENGLISH
Camera
Index Button [INDEX] (pg. 26)/
Remaining Space Button/Data Battery
Button [ / ] (pg. 14, 19)
Set Lever
Move to :
Reverse Skip (pg. 24)/Up/Backlight
Compensation [
] (pg. 21)/Spot
Exposure Control [
] (pg. 21)
Move to :
Forward Skip (pg. 24)/Down/
Change Flash Setting [FLASH]
(pg. 18)/
Change LED Light Setting
[LIGHT] (pg. 18)
Move to :
Reverse Search (pg. 24)/Left/
Nightalive [NIGHT] (pg. 21)
Move to :
Forward Search (pg. 24)/Right/
Program AE [PROGRAM AE] ( pg. 20)
Press down:
Play/Pause (pg. 24)
Menu Button [MENU] (pg. 46)
Speaker (pg. 24)
Playback/Recording Mode Switching
Button [SELECT PLAY/REC] (pg. 16)
Zoom Lever [W , T
] (pg. 18)
Speaker Volume Control [–VOL+]
(pg. 24)
Still Image Shooting Button [SNAPSHOT]
(pg. 17)
Function Button [FUNCTION] (pg. 22)
Direct DVD Button [DIRECT DVD]
( pg. 41 and PC OPERATION GUIDE)
Direct Backup Button [DIRECT BACK UP]
( PC OPERATION GUIDE)/Event Button
[EVENT] (pg. 19)
Auto/Manual Mode Button [AUTO]
(pg. 20)/ Information Button [INFO]
(pg. 32)
Video Recording Start/Stop Button [REC]
( pg. 16)
Access/Charge Lamp [ACCESS/CHARGE]
(pg. 12)
(Blinks when you access fi les or charge
the battery. Do not turn off the power or
remove the battery pack/AC adapter while
accessing fi les.)
Video/Still Image Mode Lamp [ , ]
(pg. 16, 17)
Power/Mode Switch [OFF (CHARGE), ON,
MODE] (pg. 12)
Lock Button (pg. 12)
Grip Strap (pg. 14)
USB (Universal Serial Bus) Connector
[
] (pg. 38, 40 and PC OPERATION
GUIDE)
Flash (pg. 18)/
LED Light (pg. 18)
Camera Sensor
Remote Sensor (pg. 7)
Lens Cover (pg. 14)
Lens
Lens Cover Switch [ , ] (pg. 14)
Stereo Microphone
SD Card Slot (pg. 15)
Tripod Mounting Socket (pg. 14)
Stud Hole (pg. 14)
DC Input Connector [DC] (pg. 12)
Audio/Video Connector [AV]
Battery Pack Mount (pg. 12)
Battery Release Button [BATT.] (pg. 12)
Remote Control
Infrared Beam Transmitting Window
ZOOM (T/W) Buttons
Zoom In/Out ( pg. 18)
Up Button
Rotate Button (counterclockwise)
( pg. 25)
Skip Backward Button
Left Button
Back Button
PLAYLIST Button ( pg. 34)
START/STOP Button
SNAPSHOT Button ( pg. 17)
INFO Button ( pg. 32)
Skip Forward Button
PLAY/PAUSE Button
Right Button
Next Button
Down Button
Rotate Button (clockwise) ( pg. 25)
INDEX Button
DATE Button
10
During both Video and Still Image
Recording
WT
0
PM
4:55
JAN.20.2007
A
200X
F5.6
1/250
Selected Operation Mode Indicator
(pg. 20)
: Auto Mode
: Manual Mode
Tele Macro Mode Indicator (pg. 23)
Approximate Zoom Ratio (pg. 18)
Zoom Indicator (pg. 18)
AV/S Connector Input
Indicator (pg. 49)
Shutter Speed (pg. 23)
White Balance Indicator (pg. 23)
Brightness Control Indicator (pg. 48)
Battery Indicator (pg. 54)
Date/Time (pg. 13)
Manual Focus Adjustment Indicator
(pg. 22)
Selected Medium Indicator
(pg. 47, 48)
Drop Detection Indicator (Appears when
[DROP DETECTION] is set to [OFF].)
(pg. 48)
Effect Mode Indicator (pg. 23)
Program AE Mode Indicator (pg. 20)/
: Nightalive Indicator (pg. 21)
Aperture Value (F-number)
(pg. 23)
LED Light Indicator (pg. 18)
± : Exposure Adjustment Indicator
(pg. 22)
: Backlight Compensation Indicator
(pg. 21)
: Spot Exposure Control Indicator
(pg. 21)
Iris Lock Indicator (pg. 21)
During Video Recording Only
16:9
0:04:01
[5h56m]
Mode Indicator (pg. 16)
Aspect Ratio of the Image (16:9/4:3)
(pg. 47)
Picture Quality: (ultra fi ne), (fi ne),
(normal), (economy) (pg. 46)
Remaining Time (pg. 16, 57)
Counter (pg. 47)
7REC: (Appears during recording.)
(pg. 16)
79: (Appears during record-standby
mode.)
Wind Cut Indicator (pg. 47)
Event Indicator (pg. 19)
Digital Image Stabilizer (DIS) Indicator
(Appears when [DIS] is set to [OFF].)
(pg. 47)
During Still Image Recording Only
PHOTO
[9999]
FINE
10
640
4:3
Mode Indicator (pg. 17)
ISO Sensitivity
(GAIN): When set to [AUTO], there is no
indication. (pg. 47)
Focus Indicator (pg. 22)
Aspect Ratio of the Image
(16:9/4:3)
Image Size (pg. 47)
Picture Quality: FINE (fi ne) or STD
(standard) (pg. 47)
Remaining Number of Shots (pg. 57)
Continuous Shooting Mode Indicator
(pg. 48)
Shooting Indicator (pg. 17)
Self-Timer Recording Indicator (pg. 48)
Flash Mode Indicator (pg. 18)
Indications on LCD Monitor
11
ENGLISH
During Video Playback
9:55:01
PM
4:55
JAN.20.2007
X-60
Mode Indicator (pg. 24)
: Playlist Playback Indicator (Appears
when playing back a playlist.) (pg. 35)
: Event Search Playback Indicator
(Appears when playing back a video fi le
from the event search.) (pg. 27)
: Date Search Playback Indicator
(Appears when playing back a video fi le
from the date search.) (pg. 26)
Picture Quality: (ultra fi ne), (fi ne),
(normal), (economy) (pg. 46)
Playback Mode (pg. 24)
U : Playback
9 : Pause
5
: Forward Search
3
: Reverse Search
9U : Forward Slow-Motion
Y9 : Reverse Slow-Motion
(The number on the left shows speed.)
Counter (pg. 47)
Volume Level Indicator
Battery Indicator (pg. 54)
Date/Time (pg. 13)
Selected Medium Indicator (pg. 47, 48)
Drop Detection Indicator (Appears when
[DROP DETECTION] is set to [OFF].)
( pg. 48)
Effect Mode Indicator (pg. 28)
Wipe/Fader Effect Indicator (pg. 28)
During Still Image Playback
PM
4:55
JAN.20.2007
101-0098
Mode Indicator (pg. 25)
Folder/File Number
Slide Show Playback Indicator (pg. 25)
Battery Indicator (pg. 54)
Date/Time (pg. 49)
Selected Medium Indicator (pg. 47, 48)
Drop Detection Indicator (Appears when
[DROP DETECTION] is set to [OFF].)
(pg. 48)
Effect Mode Indicator (pg. 28)
Operation guide display
The operation guide is displayed at the
bottom of the screen during menu display
etc.
SELECT
SET QUIT
12
Be sure to confi gure the following three
settings before use.
Charging the Battery Pack
1 Set the power/mode switch to OFF.
Slide while pressing down the lock button.
MODE
OFF
(CHARGE)
ON
2 Attach the battery pack.
Slide the battery pack down until it locks
in place.
3 Connect the AC adapter.
You can also connect the AC
adapter using the Everio dock connector.
( pg. 6)
The access/charge lamp blinks to indicate
charging has started.
When the lamp goes out, charging is
nished. Unplug the AC adapter from the
AC outlet and disconnect the AC adapter
from the camera.
Necessary Settings before Use
MENU
Access/Charge Lamp
Power/Mode Switch
Set Lever
Bottom of the Camera
BATT.
DC Connector
AC Adapter
To AC Outlet
(110V to 240V)
Open the cover.
Required charging / recording time (approx.)
The values within ( ) are the times when the LED light is on.
Battery pack Charging time
Recording time
GZ-MG255 GZ-MG155 GZ-MG130
BN-VF808U
(Provided)
1 hr. 30 min. 1 hr. 15 min.
1 hr. 30 min.
(1 hr. 25 min.)
1 hr. 35 min.
(1 hr. 30 min.)
BN-VF815U 2 hr. 40 min. 2 hr. 35 min.
3 hr. 5 min.
(2 hr. 55 min.)
3 hr. 15 min.
(3 hr. 5 min.)
BN-VF823U 3 hr. 50 min. 3 hr. 50 min.
4 hr. 35 min.
(4 hr. 20 min.)
4 hr. 55 min.
(4 hr. 35 min.)
13
ENGLISH
8 To detach the battery pack
Slide and hold BATT. (
step 2), then
remove the battery pack.
8 To check the remaining battery power
See page 14.
NOTES
You can also use the camera with just the AC
adapter.
Please do not pull or bend the AC adapter plug
and cable. This may damage the AC adapter.
Language Setting
The language on the display can be changed.
1 Set the power/mode switch to ON.
Slide while pressing down the lock button.
MODE
OFF
(CHARGE)
ON
2
MENU
REC MEDIA FOR VIDEO
SCENE COUNTER
ZOOM
QUALITY
DIS
VIDEO
SELECT SET QUIT
3
REC MEDIA FOR VIDEO
SCENE COUNTER
ZOOM
QUALITY
DIS
VIDEO
SELECT SET QUIT
4 Select [GENERAL].
Select
Set
QUICK RESTART
AUTO POWER OFF
DROP DETECTION
BRIGHT
REMOTE
GENERAL
SELECT SET QUIT
5 Select [LANGUAGE].
Select
Set
ENGLISH
GENERAL
SELECT SET QUIT
6 Select the desired language.
Select
Set
8 To return to the previous screen
Move the set lever to .
8 To exit the screen
Press MENU.
Date/Time Setting
After performing steps 1-4 ( left column)
5 Select [ CLOCK ADJUST].
Select
Set
JAN 31
11
AM
07
2007
DATE TIME
GENERAL
SELECT SET QUIT
6 Set the date and time.
Select
Set
Repeat this step to input the month, day,
year, hour and minute.
8 To return to the previous screen
Move the set lever to .
8 To exit the screen
Press MENU.
You have now fi nished confi guring the
necessary settings.
8 To use the camera right away
See page 16.
8 To confi gure other settings
See page 14.
14
Other Settings
Grip Adjustment
Open the pad and make grip adjustments.
Lens Cover
When not using the camera, close the lens
cover to protect the lens.
Close the lens cover
Open the lens cover
NOTE
Do not push the lens cover strongly. Doing so
may cause damage to the lens.
Checking the Remaining Battery
Power
Preparation:
Set the power/mode switch to OFF.
Attach the battery pack.
INDEX
BATTERY CONDITION
MAX TIME
min
100%
50%
0%
Battery information is displayed for approx. 5
seconds if the button is pressed and released
quickly, and for approx. 15 seconds if the
button is pressed and held for several seconds.
NOTES
If “COMMUNICATING ERROR” appears,
there may be a problem with your battery.
In such a case, consult your nearest JVC
dealer.
The recordable time display should only be
used as a guide. It is displayed in 10 minute
units.
Tripod Mounting
Align the camera stud hole with the tripod
stud, and the mounting socket with the screw,
and then rotate the camera clockwise to
mount it to the tripod.
NOTE
Do not use a tripod on unsteady or unlevel
surfaces. It could tip over, causing serious
damage to the camera.
INDEX
Lens Cover
Switch
Power/Mode
Switch
Bottom of the
Camera
15
ENGLISH
When Using an SD Card
If you want to record to an SD card, the
following three operations need to be
performed.
Compatible SD cards:
Panasonic, TOSHIBA and SanDisk.
128 MB to 4 GB.
If other media are used, they may fail to
record data correctly, or they may lose data
that had already been recorded.
For video recording, use a high-speed SD
card (at least 10 MB/s).
MultiMediaCards are not supported.
Insert an SD card
Preparation:
Set the power/mode switch to OFF.
1 Open the SD card cover.
Bottom of the
Camera
2 Firmly insert the card with its clipped
edge fi rst.
Clipped Edge
3 Close the SD card cover.
8 To remove an SD card
Push the SD card once.
After the card comes out a little, pull it out.
NOTES
Insert and remove the SD card only while
the power is turned off. Otherwise, data on
the card may be corrupted.
Do not touch the terminal on the reverse
side of the label.
Change the recording medium
The camera is programmed to record on the
built-in hard disk when it is shipped from the
factory. You can change the recording medium
to SD card.
Set [REC MEDIA FOR VIDEO] and [REC
MEDIA FOR IMAGE] to [SD]. ( pg. 47,
48)
Format an SD card when using it for
the fi rst time
This will also ensure stable speeds and
operation when accessing the SD card.
Select [EXECUTE] in [FORMAT SD
CARD] to format the card. ( pg. 50)
16
Recording Files
Video Recording
Preparation: Set the power/mode switch to ON.
Press the PLAY/REC button to
select recording mode.
PLAY/REC
SELECT
16:9
[5h56m]
Press the REC button to start
recording.
REC
REC
[5h56m]
Approximate remaining time for
recording appears.
8 To stop recording
Press the REC button again.
8 To change the picture quality
Change the settings in [QUALITY].
(
pg. 46)
8 To register a fi le to an event
See page 19.
8 To change the aspect ratio of the image
(16:9/4:3)
Change the settings in [16:9 WIDE
RECORDING]. (
pg. 47)
Slide the power/mode switch to
MODE to select (video) mode.
MODE
OFF
ON
The switch returns to
the original position
when it is released.
The lamp on the camera lights up.
NOTES
The video recording mode is automatically selected when you turn the camera’s power off and then
on again.
If the camera is not operated for 5 minutes while the power is on, it turns itself off automatically to
conserve power. To turn the camera on again when using the battery pack, set the power/mode switch
to OFF, then to ON. When using the AC adapter, perform any operation such as zooming.
Video fi les are given the names MOV_001.MOD to MOV_009.MOD, MOV_00A.MOD to
MOV_00F.MOD, and MOV_010.MOD in order of recording.
After recording video for 12 consecutive hours, recording stops automatically.
A new fi le will be created for every 4 GB of continuous shooting.
This camera records video in MPEG2 format compliant with SD-VIDEO format. Remember that this
camera is not compatible with other digital video formats.
Do not move or shake the camera suddenly during recording. If you do so, the sound of the hard disk
drive may be recorded.
17
ENGLISH
Still Image Recording
Preparation: Set the power/mode switch to ON.
Slide the power/mode switch to
MODE to select (still image)
mode.
MODE
OFF
ON
The switch returns
to the original
position when it is
released.
The
lamp on the camera lights up.
Press the PLAY/REC button to
select recording mode.
PLAY/REC
SELECT
[9999]
FINE
640
Press and hold the SNAPSHOT
button halfway.
[
FINE
640
The indicator becomes green when
the captured image is focused.
Press the SNAPSHOT button to
start recording.
[9999]
FINE
4
0
NOTE
If the camera is not operated for 5 minutes while the power is on, it turns itself off automatically to
conserve power. To turn the camera on again when using the battery pack, set the power/mode switch
to OFF, then to ON. When using the AC adapter, perform any operation such as zooming.
8 To change the picture quality
Change the settings in [QUALITY].
(
pg. 47)
8 To record still images continuously
Set [CONTINUOUS SHOOTING] to
[ON]. (
pg. 48)
8
To change the image size
Change the settings in [IMAGE SIZE].
(
pg. 47)
18
Recording Files (Continued)
Zooming
Preparation:
Slide the power/mode switch to MODE to
select
or mode.
Press the PLAY/REC button to select
recording mode.
Zoom out Zoom in
W: Wide angle T: Telephoto
Maximum Zoom Ratio (Factory-preset)
Model
mode mode
GZ-MG255 40X 10X
GZ-MG155 64X 27X
GZ-MG130 68X 34X
8 To change the maximum zoom ratio (for
mode only)
Change the settings in [ZOOM]. ( pg. 46)
NOTE
Macro shooting is possible as close as
approx. 5 cm (2
) to the subject when the
zoom lever is set all the way to W.
LED Light
Preparation:
Slide the power/mode switch to MODE to
select
or mode.
Press the PLAY/REC button to select
recording mode.
A
Each time you move the set lever to ,
setting changes.
The light remains on regardless
of the surrounding conditions.
The light turns on automatically
when shooting in insuffi cient
light conditions.
No display
Disables this function.
Flash – mode only
Preparation:
Slide the power/mode switch to MODE to
select
mode.
Press the PLAY/REC button to select
recording mode.
[9999]
FINE
4
0
Each time you move the set lever to ,
setting changes.
The fl ash fi res automatically.
The fl ash fi res automatically
but reduces the red-eye
phenomenon of the subject’s
eyes.
The fl ash fi res regardless of the
shooting condition.
The fl ash fi res. The shutter
speed becomes slower, so
the background can also be
brightened.
No display
Disables this function.
INDEX
Zoom Lever
PLAY/REC
Button
Set Lever
Power/Mode
Switch
19
ENGLISH
Registering Files to Events
mode only
If you select an event to register the fi le to
before starting recording, the fi le will be
registered to the selected event, thus making
the fi le easy to fi nd at playback. There are up
to 3 different destinations within each event
(for example: BABY1, BABY2, BABY3).
Preparation:
Slide the power/mode switch to MODE to
select
mode.
Press the PLAY/REC button to select
recording mode.
1
ON/SELECT
CHANGE EVENT REG.
OFF
2 Select [ON/SELECT].
Select
Set
VACATION
1/ 3
NON SECTION NEXT PAGE
SELECT
SET QUIT
3 Select the event that you want to
register the fi le to.
To select a different destination, select
[NEXT PAGE].
To cancel the event registration, select
[NON SECTION].
Select
Set
The selected event is displayed on the
screen. Press the REC button to start
recording.
8 To exit the screen
Press EVENT.
8 To search by event for a fi le to play back
See page 26.
NOTE
Once you select to register a fi le to a certain
event, the setting will remain even if you turn
the power off. Unless you change the setting,
you will register a fi le to the same event that
you had previously selected.
Checking the Remaining Space on
the Recording Media
mode only
Preparation:
Slide the power/mode switch to MODE to
select
mode.
Press the PLAY/REC button to select
recording mode.
INDEX
MAX RECORDING TIME
7h30m
11h15m
22h30m
45h00m
HDD
FREE
USED
The maximum recording time is displayed for
each picture quality mode (
: ULTRA FINE,
: FINE, : NORMAL, : ECONOMY).
8 To return to the normal screen
Press the button again.
20
Manual recording mode enables you to set
the focus and screen brightness etc. manually.
You need to switch to this mode because auto
recording mode, which adjusts these settings
automatically, is selected by default.
To Change to Manual Recording
Mode
Preparation:
Slide the power/mode switch to MODE to
select
or mode.
Press the PLAY/REC button to select
recording mode.
Press twice.
INFO
8 To return to the auto recording mode
Press the AUTO button so that the
indicator appears.
Program AE
You can record videos or still images with
optimum brightness by adjusting the exposure
and shutter speed to suit your surroundings or
the subject.
After performing “To Change to Manual
Recording Mode” ( left column)
1
OFF
2 Select the desired setting.
For details on each setting, see below.
Select
Set
8 To cancel the program AE
Select [OFF] in step 2.
8 Items for program AE setting
PORTRAIT:
The subject in the foreground is
accentuated by blurring the background.
SPORTS :
Records fast moving subjects clearly.
SNOW :
Compensates for subjects that may
appear too dark when shooting in
extremely bright surroundings, such as in
snow.
SPOTLIGHT :
Select this when a spotlight makes a
subject appear too bright.
TWILIGHT :
Makes evening scenes look more natural.
Manual Recording
INFO
FUNCTION
Power/Mode
Switch
PLAY/REC Button
Set Lever
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120

JVC Everio GZ-MG255U Instructions Manual

Catégorie
Caméscopes
Taper
Instructions Manual
Ce manuel convient également à

dans d''autres langues