RIDGID 1000RSDS Mode d'emploi

600004-005 B 1/19

Dual Suction Sump Pumps

Intended for Indoor Use Only

Operating Instructions and Parts Manual Dual Suction Series

Please read and save these instructions. Read carefully before attempting to assemble, install,

operate or maintain the product described. Protect yourself and others by observing all safety

information. Failure to comply with instructions could result in personal injury and/or property

damage! Retain instructions for future reference.

SPECIFICATIONS

POWER SUPPLY REQUIREMENTS 120 V, 60 Hz

MOTOR Intermittent

HORSEPOWER

1 HP...............(

1000RSDS

)

1/2 HP............

(500RSDS)

1/3 HP............

(330RSDS)

CIRCUIT REQUIREMENTS 15 A (minimum)

DIMENSIONS

12 in. high x 7-1/2in. base

(ALL MODELS)

ON LEVEL (FACTORY SET)

Approximately 9 in.

(ALL MODELS)

OFF LEVEL (FACTORY SET)

Approximately 4 in.

(ALL MODELS)

PERFORMANCE

Model HP Discharge Head

0 ft

5 ft 10 ft 15 ft 20 ft

1000RSDS 1

Gal / hr 6500 6270 5550 4800 3500

500RSDS

1/2

Gal / hr 5200 4400 3500 2500 1200

330RSDS 1/3

Gal / hr 4500 3000 2900 1800 500

CONSTRUCTION

MOTOR HOUSING Stainless Steel

MOTOR SHAFT Carbon Steel

IMPELLER Dual Glass Reinforced Thermoplastic

VOLUTE Cast Iron

PUMP DISCHARGE 1-1/2 in. NPT

INSTALLATION MANUAL

2

SAFETY SIGNAL WORDS

This manual contains information that is very important

to know and understand. This information is provided for

SAFETY and to PREVENT EQUIPMENT PROBLEMS. To

help recognize this information, observe all safety information

labeled danger, warning, caution, and notice.

DUAL SUCTION SUMP PUMP

DESCRIPTION

Sump Pumps are automatic pumps used to remove ground

water from sump pits. The most common application is for

basement drainage to prevent ﬂooding in residential buildings.

Sump pumps are designed to pump clear water only. These

pumps are not designed to be used with a portable generator.

The top suction (above the impeller) eliminates the risk of airlock

and the suction screen ﬁlters debris, which minimizes clogging.

This helps deliver ultimate water ﬂow. The bottom suction (below

the impeller) passes up to 1/2 in. solids and ﬁlers debris through

the heavy duty, cast iron, multi-ring strainer base to reduce

clogging.

Installation of this pump outdoors, unprotected from the

weather, may cause hazardous conditions and will void warranty.

If using outdoors, protect pump from direct weather elements

such as sun, rain, sleet, snow, and extreme temperature

changes. Water inside the pump may freeze, limiting its

performance and damaging the pump, pipes, and hoses.

Intended for Indoor Use Only

PLEASE SEE WWW.WAYNEPUMPS.COM FOR PRODUCT INFORMATION AND INSTALLATION VIDEOS

MAKE SURE THERE IS A PROPERLY GROUNDED RECEPTACLE

AVAILABLE. This pump is supplied with a grounding conductor

and grounding-type attachment plug. To reduce the risk of electric

shock, be certain that it is connected only to a properly grounded,

grounding-type receptacle.

S’ASSURER QU’UNE PRISE DE MISE À LA TERRE EST DISPONIBLE.

Cette pompe est fournie avec un conducteur et une ﬁche de mise à

la terre. Pour réduire le risque de choc électrique, s’assurer qu’elle

est branchée seulement à une prise de courant correctement mise

à la terre.

FOR ADDED SAFETY the receptacle must be protected with a ground

fault circuit interrupter (GFCI). All wiring must be performed by a

qualiﬁed licensed electrician and comply with the National Electric

Code and all applicable local codes and ordinances.

POUR PLUS DE SÉCURITÉ, la prise de courant doit être protégée par

un disjoncteur de fuite à la terre. Tout le câblage doit être effectué

par un électricien qualiﬁé et être conforme au Code électrique

national et à tous les codes et règlements locaux applicables.

NEVER REMOVE THE GROUND PRONG from the plug or bypass the

grounding wires.

NE JAMAIS RETIRER LE CONNECTEUR DE MISE À LA TERRE de la prise

ou contourner les ﬁls de mise à la terre.

MAKE SURE THE POWER SUPPLY HAS A FUSE OR CIRCUIT BREAKER

rated to handle the current (amps) noted on the pump nameplate

or cordtag.

S’ASSURER QUE L’ALIMENTATION ÉLECTRIQUE EST MUNIE D’UN

FUSIBLE OU D’UN DISJONCTEUR d’une valeur nominale appropriée

pour supporter l’intensité du courant (ampérage) indiquée sur la

plaque signalétique ou l’étiquette du cordon de la pompe.

IMPORTANT SAFETY INFORMATION

CONSIGNES DE SÉCURITÉ

IMPORTANTES

WARNING INDICATES A POTENTIALLY HAZARDOUS SITUATION

WHICH, IF NOT AVOIDED, COULD RESULT IN DEATH OR

SERIOUS INJURY.

LA MENTION AVERTISSEMENT INDIQUE UNE SITUATION

POTENTIELLEMENT DANGEREUSE QUI, SI ELLE N’EST PAS

ÉVITÉE, RISQUE D’ENTRAÎNER DES LÉSIONS CORPORELLES

GRAVES OU MÊME LA MORT.

RISK OF ELECTRIC SHOCK. TO REDUCE THIS RISK,

OBSERVE THE FOLLOWING WARNINGS:

RISQUE DE CHOC ÉLECTRIQUE. POUR RÉDUIRE CE

RISQUE, TENIR COMPTE DES AVERTISSEMENTS

SUIVANTS

UNPACKING

Inspect this unit before it is used. Occasionally, products are damaged

during shipment. If the pump or components are damaged, return

the unit to the place of purchase for replacement, or call Customer

Support (1-877-9RIDGID).

INSTALLATION MANUAL

3

ALWAYS DISCONNECT THE PUMP from power supply before installing,

servicing or making any adjustments.

TOUJOURS METTRE LA POMPE HORS TENSION avant de procéder à

l’installation, à l’entretien ou à des réglages.

DO NOT WALK on the ﬂoor when water is present until all power is

turned off. If the electric panel is in the basement, call an electrician.

NE PAS MARCHER sur un sol mouillé avant que l’alimentation

générale ne soit coupée. Si le tableau électrique est en sous-sol,

appeler un électricien.

NEVER HANDLE A PUMP or motor with wet hands or when standing

on a wet or damp ﬂoor while the pump is plugged into the power

supply.

NE JAMAIS MANIPULER UNE POMPE ou un moteur de pompe avec

les mains mouillées ou debout dans l’eau ou sur une surface

humide.

RISK OF ELECTRIC SHOCK. This pump has not been investigated for

use in swimming pool and marine areas.

RISQUE DE CHOC ÉLECTRIQUE. Cette pompe n’a pas fait l’objet

de vériﬁcation pour une utilisation dans les piscines et les aires

marines.

DO NOT USE TO PUMP FLAMMABLE OR EXPLOSIVE FLUIDS such as

gasoline, fuel oil, kerosene, etc. Do not use in a ﬂammable and/or

explosive atmosphere. Pump should only be used to pump clear

water. Personal injury and/or property damage will result and void

warranty.

NE PAS UTILISER POUR POMPER DES FLUIDES INFLAMMABLES OU

EXPLOSIFS tels que l’essence, le mazout, le kérosène, etc. Ne

pas utiliser dans un environnement inﬂammable et/ou explosif.

La pompe ne doit être utilisée que pour pomper de l’eau claire.

Des blessures corporelles et/ou des dégâts matériels pourraient

en résulter.

PUMPS ARE NOT DESIGNED TO TRANSFER WATER INTENDED FOR

DRINKING. Do not use the pump for moving water that will be

used for portable/drinking water. Pump should only be used

in applications for which it is designed.

LES POMPES NE SONT PAS CONÇUES POUR L’ACHEMINEMENT D’EAU

DESTINÉE À LA CONSOMMATION. Ne pas utiliser la pompe

pour transporter de l’eau qui sera utilisée comme de l’eau

potable/destinée à la consommation. La pompe doit être

utilisée uniquement dans les applications pour lesquelles

elle est conçue.

DO NOT USE AN EXTENSION CORD OR SURGE PROTECTOR. Extension

cords and/or surge protectors could present a safety hazard if not

sized properly, become damaged or the connection falls into the

sump. If receptacle is not within reach of the pump’s power cord,

contact a qualiﬁed licensed electrician to install a new receptacle.

NE PAS UTILISER DE RALLONGE NI DE PROTECTEUR DE SURTENSION.

Les rallonges et/ou les protecteurs de surtension peuvent présenter

un danger pour la sécurité s’ils ne sont pas correctement calibrés,

s’ils sont endommagés ou si le raccordement tombe dans le

puisard. Si la prise n’est pas à portée du cordon d’alimentation

de la pompe, contacter un électricien qualiﬁé pour installer une

nouvelle prise.

CAUTION INDICATES A POTENTIALLY HAZARDOUS SITUATION

WHICH, IF NOT AVOIDED, MAY RESULT IN MINOR OR

MODERATE INJURY.

MISE EN GARDE

LA MENTION MISE EN GARDE INDIQUE UNE SITUATION

POTENTIELLEMENT DANGEREUSE QUI, SI ELLE N’EST PAS

ÉVITÉE, POURRAIT ENTRAÎNER DES BLESSURES MINEURES

OU MODÉRÉES.

TO REDUCE THE RISK OF HAZARDS THAT CAN CAUSE

INJURY OR PROPERTY DAMAGE, OBSERVE THE FOLLOWING

WARNINGS:

POUR RÉDUIRE LE RISQUE DE DANGERS POUVANT CAUSER

DES BLESSURES OU DES DÉGÂTS MATÉRIELS, RESPECTER

LES MISES EN GARDE SUIVANTES :

IT IS THE INSTALLER’S RESPONSIBILITY TO MAKE SURE THE

PUMPS AUTOMATIC SWITCH IS ABLE TO OPERATE WITHOUT ANY

OBSTRUCTIONS WITHIN THE BASIN. It is recommended that the

installer test and observe the pump’s operation for several cycles

after installation.

IL EST DE LA RESPONSABILITÉ DE L’INSTALLATEUR DE S’ASSURER QUE

L’INTERRUPTEUR AUTOMATIQUE DE POMPE PEUT FONCTIONNER SANS

AUCUN BLOCAGE À L’INTÉRIEUR DU SYSTÈME. Il est recommandé

que l’installateur teste et observe le fonctionnement de la pompe

pendant plusieurs cycles après l’installation.

INSTALLATION MANUAL

4

IT IS REQUIRED TO USE RIGID PIPING AND FITTINGS to secure the

pump in the basin and reduce pump movement. Pump movement

can prevent the switch from operating correctly. Do not use ﬂexible

hosing.

IL EST NÉCESSAIRE D’UTILISER DES TUYAUX ET DES RACCORDS

RIGIDES pour ﬁxer la pompe dans le système et réduire les

mouvements de la pompe. Les mouvements de la pompe peuvent

empêcher l’interrupteur de fonctionner correctement. Ne pas

utiliser de tuyaux ﬂexibles.

IT IS REQUIRED TO USE A CHECK VALVE with this pump to prevent the

back-ﬂow of clear ground water after each pump cycle.

Cette pompe NÉCESSITE L’UTILISATION D’UNE VANNE DE CONTRÔLE

pour empêcher le reﬂux d’eau souterraine claire après chaque

cycle de pompage.

DO NOT INSTALL OR OPERATE THE PUMP IF IT HAS BEEN DAMAGED

IN ANY WAY.

NE PAS INSTALLER OU FAIRE FONCTIONNER LA POMPE SI ELLE A ÉTÉ

ENDOMMAGÉE DE QUELQUE MANIÈRE QUE CE SOIT.

DO NOT LIFT OR CARRY THE PUMP BY THE POWER CORD. Use the

pump’s handle or lift ring.

NE PAS SOULEVER OU PORTER LA POMPE PAR LE CORDON

D’ALIMENTATION. Utiliser la poignée ou la bague de levage de la

pompe.

AN INDEPENDENT HIGH WATER ALARM OR BACK UP PUMP SHOULD BE

USED when risk of property damage from high water levels exists.

UNE ALARME AUTONOME DE? NIVEAU D’EAU ÉLEVÉ OU UNE POMPE DE

SAUVEGARDE DOIVENT ÊTRE UTILISÉES en cas de risque de dégâts

matériels causés par des niveaux d’eau élevés.

REPLACE THE SWTICH EVERY T?WO (2) YEARS. This maintenance will

reduce the risk of improper pump operation, switch failure and/or

ﬂooding.

REMPLACER LE COMMUTATEUR TOUS LES DEUX (2) ANS. Cet entretien

réduira le risque d’utilisation incorrecte de la pompe, de défaillance

de l’interrupteur ou d’inondation.

This product can expose you to chemicals, including DEHP,

which is known to the State of California to cause cancer, birth

defects and reproductive harm. For more information, go to

www.P65Warnings.ca.gov.

Ce produit peut vous exposer à des produits chimiques,

notamment du DOP, reconnus par l’État de Californie comme

étant cancérigènes et à l’origine d’anomalies congénitales et de

problèmes de l’appareil reproductif. Pour plus de renseignements,

visiter le site www.P65Warnings.ca.gov.

TETHER FLOAT SWTICH This ﬂoat is adjustable. By adjusting the

tether switch it can affect the speciﬁcations of the application of

the pump and can change the life expectancy of the unit.

L’INTERRUPTEUR DU FLOTTEUR À AMARRE est réglable. L’ajuster

peut affecter les spéciﬁcations d’utilisation de la pompe et peut en

modiﬁer la durée de vie.

INSTALLATION MANUAL

5

TYPICAL SUMP INSTALLATION

1. This installation must be in accordance with the National

Electric Code and all applicable local codes and ordinances.

2. Clean the basin of all debris.

3. Set the pump on a solid, level surface. Do not place pump

directly on clay, earth, gravel, or sand. A brick or block may

be installed under the pump to provide a solid base.

4. Verify the ﬂoat switch has at least 1 inch clearance to

the side wall of the basin and is free of any possible

obstructions.

5. If optional control device or ﬂoat is used, follow mounting

instructions supplied with device or ﬂoat.

6. Install discharge plumbing according to local, regional and

state codes. Do not reduce the discharge pipe size below

that which is provided on the pump.

7. Install a union to allow easy removal of the pump for

cleaning and service.

8. Install a check valve (required) to prevent back-ﬂow. It should

be installed above the union.

9. A gate valve or ball valve should be installed above the

check valve as required by local, regional or state codes.

10. Connect remaining discharge pipe. The remainder of

the discharge line should be as short as possible with a

minimum number of turns.

11. Secure power supply cord to discharge pipe using cable or

zip ties to prevent possible switch entanglement.

12. Connect pump power supply cord to a ground fault circuit

interrupter (GFCI) receptacle.

13. Fill the basin with water. The pump will start when the water

level has reached the switch-on level. Verify the pump is

operating normally. If the discharge line is exposed to freezing

temperatures, the pipe must be positioned in a downward

slope away from the foundation so any remaining water will

drain away and not freeze.

14. Secure a basin/tank cover and gasket to the basin to prevent

debris from falling into the basin, prevent personal injury, and to

contain gases and/or odors.

Vertical Submersible Sump

1

2

3

5

8

9

7

6

1. GFCI OUTLET 6. DISCHARGE PIPE

2. CHECK VALVE 7. SUMP PUMP

3. VENT PIPE 8. SWITCH

4. GASKET/BASIN LID

5 PIPE INLET

9. BASIN

MINIMUM

BASIN

HEIGHT (SEE

CHART,

COLUMN B)

MINIMUM BASIN DIAMETER

(SEE CHART, COLUMN A)

4

Basin/Pit Size

Speciﬁcations

A

Minimum

Basin Diameter

B

Minimum

Basin Height

Vertical Float Switch 11 in. 22 in.

INSTALLATION MANUAL

6

TROUBLESHOOTING

Symptoms Possible Cause(s) Suggested Remedies

Pump will not

start or run

1. Water level too low

2. Blown fuse or tripped circuit breaker

3. Low supply voltage

4. Motor

5. Switch

6. Inlet clogged

7. Switch obstruction

1. Water must be at the appropriate level to activate switch

2. If blown, determine cause and then either replace with proper

sized fuse or reset breaker

3. Contact an electrician

4. Replace pump

5. Replace switch

6. Remove debris

7. Remove obstruction to verify free motion of switch

Pump starts and

stops too often

1. Back-flow of water from discharge

pipe

2. Switch

3. Check valve not functioning properly

or leaking

1. Install check valve

2. Replace switch

3. Remove and examine check valve for prop er in stal la tion and free

operation. Replace check valve if necessary.

Pump shuts off

and turns on

independently

of switch (trips

thermal overload

protection)

1. Switch

2. Switch obstruction

3. Obstruction in discharge pipe

4. Low supply voltage

1. Replace switch

2. Remove obstruction to verify free motion of switch

3. Remove obstruction in discharge piping

4. Contact an electrician.

TROUBLESHOOTING WARNINGS

ALWAYS DISCONNECT THE PUMP FROM POWER SUPPLY before

installing, servicing or making any adjustments.

TOUJOURS METTRE LA POMPE HORS TENSION avant de procéder à

l’installation, à l’entretien ou à des réglages.

LET PUMP COOL FOR A MINIMUM OF 2 HOURS BEFORE ATTEMPTING TO

SERVICE. Submersible pumps contain oil that become pressurized

and hot under normal operating conditions.

LAISSER REFROIDIR LA POMPE PENDANT AU MOINS 2 HEURES AVANT

D’ESSAYER DE LA RÉPARER. Les pompes submersibles contiennent

de l’huile qui devient pressurisée et chaude dans des conditions

normales de fonctionnement.

1. Submersible pump models have permanently lubricated

bearings and require no additional lubrication.

2. Submersible pumps contain dielectric oil for cooling.

Dielectric oil can be harmful to the environment. Follow

state environmental laws when disposing of oil.

3. The pump motor is equipped with automatic resetting

thermal protector and may restart unexpectedly. Protector

tripping is an indication of motor overloading as a result of

operating the pump at low heads, excessively high or low

voltage, inadequate wiring, incorrect motor conditions, or at

the end of its life.

INSTALLATION MANUAL

7

TROUBLESHOOTING (CONTINUED)

Symptoms Possible Cause(s) Suggested Remedies

Pump trips GFCI 1. Bad GFCI

2. Bad pump

1. Contact and electrician to replace GFCI

2. Replace pump

Pump will not

shut off

1. Switch

2. Switch obstructions

3. Restricted discharge (obstruction in

piping)

4. Excessive inflow or pump not

properly sized for application

1. Replace switch

2. Remove obstruction to verify free motion of switch

3. Remove obstruction from discharge piping

4. Recheck all sizing calculations to determine proper pump size

Pump operates

but delivers little

or no water

1. Low supply voltage

2. Inlet clogged

3. Broken impeller

4. Pump not properly sized for

application

5. Check valve stuck closed or

installed backwards

6. Shut off valve closed

1. Contact an electrician

2. Remove debris

3. Replace pump

4. Recheck all sizing calculations to determine proper pump size

5. Remove and examine check valve for proper installation and free

operation

6. Open valve

ROUTINE MAINTENANCE

The pump should be inspected 3-4 times per year for pump movement or buildup of debris on the switch or ﬂoat. Reposition

pump if it has moved. Remove any debris that could interfere with the operation of the switch. Lack of proper routine maintenance

will void warranty.

• Make sure the pump is plugged in to a working ground fault circuit interrupter (GFCI) outlet and the cord is in good shape.

In damp areas, GFCI breakers may trip, effectively shutting off the sump pump. Check in on your sump pump and reset the

GFCI if necessary. Replace pump if it continues to trip a known good GFCI.

• Ensure the pump itself is standing upright. Vibrations during operation can cause it to fall or tilt onto one side. This can jam

the ﬂoat arm so it can’t activate the pump.

• Pour a bucket of water into the pit to make sure the pump starts automatically and the water drains quickly once the pump

is on. If the pump doesn’t start, have it serviced or replaced.

• Replace the switch every two (2) years. This maintence will reduce the risk of improper pump operation, switch failure and/

or ﬂooding.

WARRANTY & SERVICE PARTS SHEET - REPLACEMENT PARTS

8

1

2

1

REPAIR KITS

REF. NO. DESCRIPTION MODELS

F50CISDS, F33CISDS

1 FLOAT KIT 60038-WYN1

2 TOP COVER ASSEMBLY

(4 SCREW TOP)

60017-WYN2

9

FOR REPLACEMENT

PARTS OR CUSTOMER SUPPORT,

CALL 1-1-877-9RIDGID

Please provide following information:

- Model number

- Serial number on cord tag (not to be removed)

- Part description and number as shown in parts list

LIMITED WARRANTY

For ﬁve years for 1000RSDS, 500RSDS, and 330RSDS models from the date of purchase, from an authorized dealer, RIDGID Pumps will repair or replace, at its option

for the original purchaser, any part or parts of its Sump Pumps or Water Pumps (“Product”) found upon examination by RIDGID Pumps to be defective in materials

or workmanship. Please call RIDGID Pumps (1-877-9RIDGID) for warranty instructions. Be prepared to provide the model number and the serial number when

exercising this warranty. All transportation charges on Products or parts submitted for repair or replacement must be paid by purchaser. This Limited Warranty is

not transferrable.This Limited Warranty does not cover Products which have been damaged as a result of accident, abuse, misuse, neglect, improper installation,

improper maintenance, or failure to operate in accordance with WAYNE’s written instructions.

This Limited Warranty does not cover Products which have been damaged as a result of accident, abuse, misuse, neglect, improper installation, improper

maintenance, or failure to operate in accordance with RIDGID Pumps’ written instructions.

THIS WARRANTY IS IN LIEU OF ANY AND ALL OTHER WARRANTIES, OBLIGATIONS OR AGREEMENTS, EXPRESSED OR IMPLIED, INCLUDING ANY IMPLIED

WARRANTY OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE, AND ANY RIGHTS OR REMEDIES AGAINST ANY PERSON OR ENTITY UNDER THE

UNIFORM COMMERCIAL CODE OR OTHERWISE WITH RESPECT TO THE SALE OF THE PRODUCT. THE REMEDIES AND OBLIGATIONS STATED IN THIS WARRANTY ARE

THE SOLE AND EXCLUSIVE REMEDIES OF AND OBLIGATIONS TO THE OWNER FOR ANY AND ALL MATTERS ARISING WITH RESPECT TO OR IN ANY WAY CONNECTED

WITH THE PRODUCT, REGARDLESS OF THE SOURCE OR PROVIDER OF SUCH GOODS. IN NO EVENT, WHETHER AS A RESULT OF BREACH OF CONTRACT, WARRANTY

TORT (INCLUDING NEGLIGENCE) OR OTHERWISE, SHALL RIDGID PUMPS OR ANY AFFILIATE BE LIABLE FOR ANY SPECIAL, INCIDENTAL OR CONSEQUENTIAL

DAMAGES.

You MUST retain your purchase receipt along with this form. In the event you need to exercise a warranty claim, you MUST send a copy of the purchase receipt along

with the material or correspondence. Please call RIDGID Pumps (1-877-9RIDGID) for return authorization and instructions.

DO NOT MAIL THIS FORM TO RIDGID Pumps. Use this form only to maintain your records.

MODEL NO._____________________ SERIAL NO._________________________ INSTALLATION DATE __________________________

ATTACH YOUR RECEIPT HERE

INSTALLATION MANUAL

ADDRESS PARTS CORRESPONDENCE TO:

RIDGID Pumps

101 Production Drive

Harrison, OH 45030 U.S.A.

Thank you for making Wayne Water Systems a key part of your

home maintenance program. If properly installed, maintained

and operated in accordance with Wayne Water Systems’ written