Genie 4164 Mode d'emploi

Marque: Genie

Modèle: 4164

Catégorie: Porte de garage

Taper: Mode d'emploi

Ce manuel convient également à

4124

INSTALLER: LEAVE THIS MANUAL WITH HOMEOWNER

HOMEOWNER: SAVE THIS MANUAL FOR FUTURE REFERENCE

BELT/CHAIN/SCREW DRIVE GARAGE DOOR OPENER

PROGRAMMING, OPERATION & MAINTENANCE MANUAL

39495504268, 04/2019

SERIAL NUMBER DECAL

STOP

DO NOT return product to store,

visit www.geniecompany.com

or call Customer Service at: 1-800-35-GENIE

iDCM SERIAL NUMBER DECAL

To reduce the risk of injury to persons or damage to property, use this opener only with a sectional residential

door.

WARNING

Por reduire le risque de blessures ou de dommages materials, utillsez cet ouvre-porte uniquement pour une porte

a section re sidentielie.

AVERTISSEMENT

Refer to the assembly poster

for opener assembly and

installation instructions. Return

to this manual for programming,

operation and maintenance.

DO NOT use photocells from other manufacturers or openers with this opener.

• Standard Models

• BBU Models

• iDCM Models

• Integrated LED lighted Models

Safety & General Information

Introduction .............................................................. 1

Safety Noti cations ................................................. 2

Important Installation Instructions ................... 3

Standard & Safety Features ....................... 4

Programming Information

Introduction to opener programming ............ 5

Setting the DOWN Limit ....................................... 6

Setting the UP Limit ............................................... 7

Setting the Force Control ..................................... 8

Contact Reverse Test .............................................. 8

Contact Reverse Adjustment .............................. 8

Remote Control Programming ........................... 9

Keypad Programming* ........................................10

Homelink & Car2U Programming* ..................11

Integrated Aladdin Programming* .......... 12-13

Maintenance

Important Safety Instructions ...........................14

Regular Maintenance Schedule .......................15

Door Inspection & Maintenance ......................15

Remote Battery Replacement ...........................16

Light Bulb Replacement .....................................16

Special Installation Information

Force Adjustment Guide .....................................17

Clearing Remote Memory ..................................18

Use of Dongle Ports* ............................................18

Locating Safe-T-Beam® Pairs

.............................19

Adjusting Speed Control ....................................19

Troubleshooting & LED Signals............. 20-21

Replacement Parts ...................................... 22-26

DASMA Information ................................... 28-29

INDEX

SAVE THESE INSTRUCTIONS

READ AND FOLLOW ALL INSTRUCTIONS

FCC Part 15.21 Statement:

Changes or modi cations not expressly

approved by the party responsible for

compliance could void the user’s authority to

operate the equipment.

FCC / IC Statement:

This device complies with FCC Part 15

and Industry Canada licence-exempt RSS

standard(s). Operation is subject to the

following two conditions: (1) this device

may not cause harmful interference, and

(2) this device must accept any interference

received, including interference that may cause

undesired operation of the device.

Le présent appareil est conforme aux CNR

d’Industrie Canada applicables aux appareils

radio exempts de licence. L’exploitation est

autorisée aux deux conditions suivantes : (1)

l’appareil ne doit pas produire de brouillage,

et (2) l’utilisateur de l’appareil doit accepter

tout brouillage radioélectrique subi, même si le

brouillage est susceptible d’en compromettre le

fonctionnement.

Scan this code for a video of this installation

or visit: www.geniecompany.com

Belt/Chain Drive

ScrewDrive

* Abbreviated versions. See instructions that accompany

Accessory or Vehicle owners manual for full details and

instructions.

DO NOT RETURN PRODUCT TO STORE

If you require assistance or have any questions,

a knowledgeable Genie Service Technician is just

a phone call away at:

1-800-35-GENIE (1-800-354-3643)

Or visit our website at:

www.geniecompany.com

Before setting up your new garage door opener, please note the model plate on the opener and serial

number(s) located on the front of this manual. This information will be necessary should you seek

technical support via our website, customer support department or local servicing Genie dealer.

Lock, Door Detect, and Safe-T-Beam, Aladdin Connect, iDCM, are trademarks of The Genie Company. All other

trademarks are property of their rightful owners. Consistent with our policy of continuing product improve-

ments, we reserve the right to change product speci cations without prior notice or obligations. HomeLink is a

registered trademark of Gentex Corporation. Car2U is a registered trademark of Lear Corporation.

INTRODUCTION

Spanish language manuals available at:

Idioma alternativo manuales disponibles en:

www.geniecompany.com

}

Thank you for purchasing a

Genie® brand garage door

opener. The leader in garage door

opener technology.

Please take a moment to preview this manual and assembly poster

to ensure that you have the proper tools and general assembly and

fabrication skills required to install a new garage door opener.

Read and understand all Safety Warnings and Cautions contained in

this manual before proceeding.

SAFETY NOTIFICATIONS & INSTRUCTIONS

IMPORTANT SAFETY INSTRUCTIONS

OVERVIEW OF POTENTIAL HAZARDS

READ THIS SAFETY INFORMATION

Garage doors are large, heavy objects that move with the help of springs under high tension and electric motors. Since moving objects, springs under tension,

and electric motors can cause injuries, your safety and the safety of others depend on you reading the information in this manual. If you have questions or do

not understand the information presented, call your nearest trained door system technician or visit our website at www.geniecompany.com.

CONVENTIONS USED IN THESE INSTRUCTIONS

The following safety alert symbol and signal words are used throughout this manual to call attention to and identify di erent levels of hazards and special

instructions.

This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others. All safety messages will follow the safety alert

symbol and the word

“DANGER”, “WARNING”,

“CAUTION”.

•

DANGER

indicates an imminently hazardous situation which, if NOT avoided, will result in death or serious injury.

•

WARNING

indicates a potentially hazardous situation which, if NOT avoided, could result in death or serious injury.

•

CAUTION

indicates a potentially hazardous situation which, if NOT avoided, may result in injury or property damage.

•

The word

NOTE

s used to indicate important steps to be followed or important considerations.

Tous les messages concernant la sécurité seront indiqués après un symbole d’alerte de la sécurité et l’une des mentions suivantes “DANGER”,

”AVERTISSEMENT” ou “MISE EN GARDE”.

• DANGER signale une situation dangereuse imminente qui, si elle n’est pas évitée, risque d’entraîner des blessures graves, voire mortelles.

• AVERTISSEMENT signale une situation potentiellement dangereuse qui, si elle n’est pas évitée, risque d’entraîner la mort ou des blessures

graves.

• MISE EN GARDE signale une situation potentiellement dangereuse qui, si elle n’est pas évitée, risque d’entraîner des blessures ou des

dommages matériels.

• Le terme REMARQUE est utilisé pour signaler les étapes importantes à suivre ou d’importants éléments à prendre en considération.

IMPORTANTES CONSIGNES DE SÉCURITÉ

DANGER POTENTIEL EFFET PRÉVENTION

PORTE EN MOUVEMENT

AVERTISSEMENT

Pourrait entraîner des

blessures graves voire la mort

Utiliser uniquement si la porte est en vue et libre de tout obstacle.

Ne laisser personne se tenir dans l’ouverture de la porte pendant

qu’elle est en mouvement.

Ne pas permettre aux enfants de jouer avec l’opérateur de la porte.

Ne pas modi er la commande de l’opérateur à contact momentané

à moins qu’un moyen d’inversion externe soit installé.

Ne pas faire fonctionner une porte qui bloque ou dont le ressort

est cassé.

CHOC ÉLECTRIQUE

AVERTISSEMENT

Pourrait entraîner des

blessures graves voire la mort

Couper le courant avant d’enlever le couvercle de l’opérateur.

Lorsque le couvercle doit être remplacé, s’assurer que les  ls ne sont

ni coincés ni près des pièces mobiles.

L’opérateur doit être correctement mis à la terre.

TENSION ÉLEVÉE RESSORT

AVERTISSEMENT

Pourrait entraîner des

blessures graves voire la mort

Ne pas essayer d’enlever, réparer ni ajuster les ressorts ou

toute autre pièce à laquelle le ressort de la porte est attaché, y

compris blocs de bois, supports en acier, câbles ou autres articles

semblables.

Les réparations et les réglages doivent être e ectués par

technicien quali é qui se sert d’outils appropriés et qui respecte les

instructions.

POTENTIAL HAZARD EFFECT PREVENTION

MOVING DOOR

WARNING

Could result in Serious

Injury of Death

Do Not operate unless the doorway is in sight and free of

obstructions. Keep people clear of opening while door is moving.

Do Not allow children to play with the door opener.

Do Not change opener control to momentary contact unless an

external reversing means is installed.

Do Not operate a door that jambs or one that has a broken spring.

ELECTRICAL SHOCK

WARNING

Could cause Serious

Injury or Death

Turn o electrical power before removing opener cover.

When replacing the cover, make sure wires are not pinched or near

moving parts.

Opener must be electrically grounded.

HIGH SPRING TENSION

WARNING

Could cause Serious

Injury or Death

Do Not try to remove, repair or adjust springs or anything to which

door spring parts are fastened such as wood block, steel brackets,

cables or any other structure or like item.

Repairs and adjustments must be made by a trained service

representative using proper tools and instructions.

IMPORTANT INSTALLATION INSTRUCTIONS

IMPORTANTES INSTRUCTIONS D’INSTALLATION

WARNING

Opener is equipped with grounded electrical plug for

your protection, and only  ts grounded electrical

outlets. DO NOT alter plug in any way! If your have no

grounded outlets, have one installed by a licensed

electrician. Opener must be properly grounded to prevent

personal injury and equipment damage. NEVER USE AN

EXTENSION CORD! Check local building codes for any

requirement that you must have a permanent hard-wired

connection. Permanent hard-wired connections must be

performed by a licensed electrician using proper tools and

instructions.

AVERTISSEMENT

L’opérateur, qui est équipé d’une prise électrique mise à la terre

pour votre protection est compatible uniquement avec des

prises électriques mises à la terre. NE PAS modi er la  che dune

quelconque manière. Si vous n’avez pas de prises mises à la terre,

faites-en installer par un électricien agréé. L’opérateur doit être

correctement mis à la terre pour éviter les blessures corporelles et

des dommages matériels. NE JAMAIS UTILISER DE RALLONGE!

Véri ez les codes locaux des bâtiments pour connexions câblées

permanente. Les connexions câblées permanentes doivent

être e ectuées par un électricien agréé qui se servira d’outils

appropriés et respectera les consignes.

WARNING

TO REDUCE THE RISK OF SEVERE INJURY OR

DEATH

READ AND FOLLOW ALL SAFETY, INSTALLATION AND OPERATION INSTRUCTIONS. If you have any questions or do not

understand an instruction, call The Genie Company.

• DO NOT install opener on an improperly balanced door. An improperly balanced door could cause severe injury. Repairs

and adjustments to cables, spring assembly and other hardware must be made by a trained service person using proper

tools and instructions.

• Remove all ropes, and disable all locks connected to the door before installing opener.

• Where possible, install the door opener 7 feet or more above the  oor. For products having an emergency release,

mount the emergency release within reach, but at least 6 feet above the  oor and avoiding contact with vehicles to

avoid accidental release. DO NOT use emergency release cord to pull door.

• DO NOT connect the opener to the source of power until instructed to do so.

• Locate the wall control button: A) Within sight of door. B) At a minimum height of 5 feet, so small children cannot reach

it. C) Away from all moving parts of the door.

• Install the entrapment WARNING label next to the wall button or console, in a prominent location. Install the emergency

release handle on the emergency release cord.

• The opener must reverse when the door contacts a 1-1/2 inch high object on the  oor at the center of the doorway. This

is about the size of a 2” x 4” board laid  at.

AVERTISSEMENT

POUR RÉDUIRE LES RISQUES DE BLESSURES GRAVES VOIRE

MORTELLES

LIRE ET SUIVRE ATTENTIVEMENT TOUTES LES INSTRUCTIONS D’INSTALLATION ET DE FONCTIONNEMENT AINSI QUE TOUTES LES CONSIGNES

DE SÉCURITÉ. Si vous avez des questions ou si vous ne comprenez pas une instruction, veuillez contacter directement The

Genie Company.

• NE PAS installer l’opérateur sur une porte mal équilibrée. Celle-ci pourrait entraîner de graves blessures. Les réparations

et les réglages des câbles, ensembles de ressort ou tout autre article de quincaillerie doivent être e ectués par un pro-

fessionnel qui se sert d’outils appropriés et qui respecte les instructions.

• Enlever toutes les cordes et désactiver toutes les verrous de la porte avant l’installer l’opérateur.

• Dans la mesure du possible, installer l’ouvre-porte à 2,1 m ou plus au-dessus du sol. Pour les produits dotés d’un cordon

de déclenchement d’urgence, installer le déclenchement d’urgence mais au moins à 1,8 m au-dessus du sol en évitant

tout contact avec les véhicules pour éviter qu’ils ne soient déclenchés accidentellement. NE PAS utiliser d’urgence

cordon de libération pour ouvrir ou fermer la porte.

• NE PAS connecter l’opérateur à la source d’alimentation tant que l’instruction n’est pas donnée.

• Repérer la console murale: A) En vue de la porte. B) À une hauteur minimale de 1,5 m a n que les jeunes enfants ne

puissent pas l’atteindre. C) Loin de toutes pièces mobiles de la porte du garage.

• Placer l’étiquette d’AVERTISSEMENT en cas de coinçage à proximité du bouton mural ou de la console de manière à ce

qu’elle soit bien en évidence. Installer la poignée du cordon de déclenchement d’urgence.

• L’opérateur doit s’inverser lorsque la porte entre en contact avec un objet d’une hauteur de 3,8 cm placé sur le sol, au

centre de l’ouverture de la porte. Ceci équivaut environ à une planche de 5 x 10 cm posée à plat sur le sol.

SAFETY & STANDARD FEATURES

1. Safe-T-Beam® (STB) Non-Contact Reversing System:

• Places an infrared beam across the door opening.

• Only a ects the DOWN travel of the door.

• Stops an open door from closing or reverses a door while in the down travel.

• Reversing system can be overridden with constant pressure on the wired wall console only.

• The door will stop and reverse to the full open position if beam is obstructed.

• Self-diagnostic LEDs on STBs and Powerhead alert to operational issues (See Locating Safe-T-Beam® Pairs &

Troubleshooting section in this manual for more information).

2. Contact Reversing System:

• Automatically reverses a closing door upon contact with an obstruction (Force Control)

3. Manual Emergency Release pull handle & cord:

• Manually releases door from door opener. Used during a power failure or other emergency to allow manual

opening and closing of the door.

• DO NOT use emergency release cord to pull the door!

4. Automatic Lighting System:

• Lighting system turns ON when door is activated and automatically turns OFF 4 minutes later.

• Can be activated/deactivated manually from the wall console.

5. Genie Battery Backup (BBU):

• Included or optional with select models. Provides power to opener in the event of a power failure. DO NOT

install BBU until opener is fully installed, programmed and tested.

6. Integrated Aladdin Connect® (iDCM):

• Available with select models, allows operation of the garage door opener with a secure mobile device

application (app) from anywhere.

7. Wall Console:

• Wired Wall Console included with select models. Operates door opener from inside garage with an open/

close button. Has a light manual control and override. Sure-lock™ security activate switch to lock out all

remote control operation.

8. Intellicode® Encryption, Factory Programmed Remote(s) :

• An encryption system that enhances the security of the door opener by continuously changing the access

code each time the remote is used.

• Factory programmed remote control(s) included with this opener.

Vehicle

Compatible

PRGM

SET

NOTE:

Before programming the opener, check to make sure there are no objects in the garage door

opening. DO NOT allow persons to enter the area of the door while programming and operating.

The following steps list the order of programming the opener’s functional settings and install any

accessories that were included with the opener or purchased separately. These steps should be

performed in order.

1. Down Travel Limit

2. Up Travel Limit

3. Force Control

4. Contact Reverse test and adjustment

5. Remote Control Programming

• Remote control(s) included with this opener are programmed at the factory. The information

provided on this page should be used if adding additional remote controls.

6. Accessory Programming

• Program wireless keypad (If applicable)

• Program built in vehicle remote (If applicable)

• Program wireless wall console (If applicable)

• Program the Integrated Aladdin Connect (if applicable)

7. Install Battery Backup (If applicable)

Term De nitions:

Travel Limits Programmable setting to adjust how far door travels up or down.

Force Control refers to how much power is needed to move (open/close) a particular door and does

NOT require programming.

Remote & Accessory Programming synchronizes remote devices with the powerhead.

(Remote Controls, Wireless Keypad, Homelink®, Car-2-U® Systems)

Speed Control refers to how fast or slow the opener opens and closes the door. This is factory set

and does NOT require programming. NOT available on all models.

NOTE:

Each programming step has a 30 second time limit for completion after the function is initiated. After 30

seconds, both LED’s will illuminate RED indicating time has expired and the step must be restarted. Restart the

step as many times as necessary to complete the programming.

OPENER PROGRAMMING & ACCESSORY INSTALLATIONS

DOOR

Long LED

Indicator

Round LED

Indicator

Program/Set

Open Travel

Button

Close Travel

Button

Programming Button Layout

PRGM

SET

PRGM

SET

PRGM

SET

PRGM

SET

PRGM

SET

WARNING

• Make sure doorway is in full view and clear of obstacles and

people to avoid injury or property damage.

• DO NOT operate this unit from the wall control before LIMITS

are set. Severe damage to the opener could occur.

• The carriage MUST be engaged to turnbuckle BEFORE setting

limits. See installation poster or call Customer Service at

1-800-35-GENIE or visit www.geniecompany.com.

• DO NOT set limits with Battery Backup attached. AC power

MUST be connected to the opener while setting limits for

proper operation.

AVERTISSEMENT

• S’assurer que le passage de la porte est visible et dégagé, à

savoir sans obstacles ni personne a n d’éviter toute blessure

potentielle ou dommage matériel.

• NE PAS utiliser cette unité avec la console murale avant

d’avoir réglé les LIMITES. L’ouvre-porte pourrait subir de

sérieux dommages.

• La tendeur DOIT être engagée dans le chariot AVANT de

régler les limites. Voir le poster d’installation (si fourni) ou

appelez le service clientèle au 1-800-35-GENIE ou visitez le

site www.geniecompany.com.

• NE PAS  xer de limites en mode batterie de secours.

L’alimentation CA DOIT être branchée sur l’ouvre-porte,

pendant le réglage des limites, pour assurer un bon

fonctionnement.

1. Press and hold the DOWN arrow button.

• Long LED will light BLUE.

2. Release DOWN arrow button.

• Long LED will  ash BLUE.

3. Press and hold the DOWN arrow button until

door is fully closed.

• Use the UP arrow button if door closes too

far. Use both UP and DOWN buttons to adjust

close travel as necessary.

Door should rest on the  oor until the weather strip

is compressed enough to seal along the width of the

door. Damaged doors or uneven  oors may not seal

properly. Repair these conditions to achieve a proper

seal. DO NOT compress seal so much that the door will

bend or buckle.

4. Press and release the SET/PRGM button

• Both LEDs will  ash BLUE then go out.

The DOWN limit is now programmed.

Steady Blue

HOLD

UNTIL

LED

Lights

Flashing

Blue

RELEASE

1-2. Enter Programming Mode

3. Adjust Door Position

Programming DOWN Limit:

NOTE:

Carriage should be locked

to opener. Door should rest somewhere

between full open and closed. Do not start

with door fully open or closed.

4. Lock Programming

Flashing Blue

PRESS

RELEASE

PROGRAMMING DOWN TRAVEL LIMIT

PRGM

SET

PRGM

SET

PRGM

SET

PRGM

SET

PRGM

SET

PROGRAMMING UP TRAVEL LIMIT

Steady Blue

HOLD

UNTIL

LED

Lights

Flashing

Blue

RELEASE

1-2. Enter Programming Mode

3. Adjust Door Position

4. Lock Programming

Flashing

Blue

PRESS

RELEASE

1. Press and hold the UP arrow button.

• Long LED will light BLUE.

2. Release UP arrow button.

• Round LED will  ash BLUE.

3. Press and hold the UP arrow button until door is

fully open.

• Use the DOWN arrow button if door opens too

far. Use both UP and DOWN buttons to adjust

open travel as necessary.

Door should fully open so that door seal is even with

door header. Do Not adjust so much that the door will

bend or buckle or stretch door spring cables backward.

4. Press and release the SET/PRGM button

• Both LEDs will  ash BLUE then go out.

The UP limit is now programmed.

Programming UP Limit:

Correct

Angle

Incorrect

Angle

Proper UP limit setting

UP limit set too high

One-Piece Door Limit Setting

Fig. A

SECTIONAL DOOR UP LIMIT:

Door should fully open so that door seal is even with

door header. Do not adjust so much that the door will

bend, buckle or stretch door spring cables backward. Stop

carriage short of the opener powerhead.

ONE-PIECE DOOR UP LIMIT:

Door should fully open so that the door arms will be in

line and push forward and up on the door.

Door damage can result If up limit is set too far back and

door arms are angled downward pushing against the

natural travel direction. Fig. A

Force Control

The force controls are automatically set when the wall

control is used for the  rst time with garage door opener.

The door MUST complete one full cycle, from full open

to full close and then, full close to full open, before the

settings are automatically recorded.

Contact Reverse Test

NOTE:

The limit and Force settings MUST BE COMPLETED

before performing the Contact Reverse Test.

Force Control Adjustments

Force settings are programmed from the factory

to remain within safe parameters. These should

not require adjustments. However, certain

circumstances may require adjustment.

Refer to the “Maintenance and Adjustment” section,

page 17, to adjust the force settings.

WARNING

TO AVOID INJURY OR DAMAGE

• NEVER adjust the force settings to adjust for damage,

including an unbalanced door, binding door track or

broken spring.

• Perform a CONTACT REVERSE TEST monthly.

AVERTISSEMENT

Pour éviter les blessures ou des dommages

• NE JAMAIS régler la force pour compenser des dommages,

y compris une porte mal équilibrée, un rail de porte coinçant

ou des ressorts cassés.

• Tous les mois, EFFECTUEZ LE TEST D’INVERSION AU CONTACT.

1. Press and release the Wall Control button

and allow the garage door to travel and stop

at the DOWN limit.

2. Press and release the wall control button and

allow the garage door to travel and stop at

the UP limit.

1. With the garage door open, lay a 2 X 4 board

 at on the  oor at the center of the door

opening.

2. Close the garage door using the wall control.

• When the door contacts the board, it should

stop and reverse direction within 2 seconds to

the full open position.

• The long LED light on the powerhead will

begin to  ash RED with the reversal of the

door.

• Remove the 2” x 4” board and operate the

opener with the wall control again. This cycle

will clear the  ashing red LEDs.

Contact Reverse Adjustment

If the door stops before contacting the board

or if it does not reverse direction to fully open

after contact with the board, it may be due to an

improperly set DOWN limit. Verify settings by:

1. Repeat the “Down Travel Limit” section to make

certain the door is closing tight against the  oor.

2. Repeat the “Force Control” section on the left to

set force limits.

3. Repeat the “Contact Reverse Test” above.

Repeat this process as needed until the door passes

the Contact Reverse Test.

Refer to the “Maintenance and Adjustment” section,

page 17, to adjust the force settings.

PROGRAMMING FORCE AND CONTACT REVERSE

PRGM

SET

PRGM

SET

PRGM

SET

NOTE:

The following instructions are for remote control transmitters

purchased separately in addition to those provided with this opener,

but can also be used if any remote(s) may require re-programming.

NOTE:

Each programming step has a 30 second time limit for

completion after the function is initiated. After 30 seconds, two

LED’s will illuminate RED indicating time has expired and the step

must be re-started. Restart the step as many times as necessary to

complete the programming.

NOTE:

Do not hold remote too close to the powerhead when

programming remote buttons.

NOTE:

Each button on each remote must be programmed

separately, following these steps.

1. Remove the battery’s protective  lm from the

remote by pulling straight down.

2. Press and hold the SET/PRGM button on the

opener for two seconds.

• The ROUND LED will turn BLUE.

• The LONG LED will then  ash PURPLE.

3. Stand at least 5 feet away from opener and

slowly press and release the desired button on

the remote two times.

• Both opener LEDs will  ash and turn o

indicating the remote has been programmed.

4. Press the desired remote button again.

• The opener should run.

To program the same remote for other garage door

openers, repeat the steps above using one of the other

remaining remote buttons.

REPEAT STEPS 1 TO 4 FOR EACH OPENER AND

REMOTE

NOTE:

It is possible to press the remote button too quickly

or lightly. If the LEDs do not go o , press the remote button

several more times to achieve con rmation.

BASIC PROGRAMMING IS COMPLETE AND YOUR GARAGE

DOOR OPENER IS READY TO USE.

See page 18 of this manual to erase remote devices from

memory.

Flashing

2. Enter Programming Mode

4. Test Remote

1. Activate Remote

Solid Blue

PRESS

RELEASE

Flashing

Purple

3. Press Remote Button Twice

PROGRAMMING ADDITIONAL REMOTE CONTROLS

THE REMOTE CONTROLS INCLUDED WITH

THIS OPENER HAVE BEEN

PROGRAMMED AT THE FACTORY FOR YOUR

CONVENIENCE.

PRGM

SET

PRGM

SET

1. Press and hold the program button on the powerhead

until the round LED turns blue, then release.

2. The round LED will go out and the long LED will begin

 ashing purple.

3. Complete programming steps.

PUTTING OPENER INTO PROGRAMMING MODE:

NOTE: The openers LEARN LED will time out in 30 seconds.

Programming must be completed within 30 seconds.

Solid Blue

PRESS

RELEASE

Flashing Purple

PROGRAMMING ACCESSORIES (abbreviated)

Program Keypad before mounting.

Activate keypad by opening battery

compartment and pull protective

tab. Reinstall compartment door to

begin programming.

TAB

Program the keypad for the  rst time* with a Personal

Identi cation Number (PIN). This PIN must be 3 to 8

digits.

1. Ensure number pad back lighting is o .

2. Press 3-5-7 in sequence.

3. Press PROGRAM key. LED will blink once per second.

4. Enter a PIN number (3-8 digits).

5. Press PROGRAM key. LED will blink twice and shut

o .

STEP 1) PROGRAMMING A PIN NUMBER (Single Door)

1. Place garage door opener into PROGRAMMING

MODE.

2. Ensure number pad back lighting is o .

3. Enter the PIN number on keypad.

4. Press the UP/DOWN key 3 to 4 times slowly until

garage door opener operates.

STEP 2) PROGRAMMING THE KEYPAD TO 1 OPENER

Single Door Operation:

1. Ensure number pad back lighting is o .

2. Enter PIN number.

3. Press the UP/DOWN key.

4. Opener will operate.

STEP 3) OPERATING THE KEYPAD WITH THE OPENER

NOTE: Keypad will remain active for 15 seconds after

a successful entry is made. During this 15 seconds ANY

key will operate the opener.

QuickView Single Door setup.

Please see complete instructions that accompany keypad

Resetting a PIN:

Press and hold both the PROGRAM key and the Up/

Down key for about  ve seconds.

The LED’s will slowly blink and then go out. When the

LED stops blinking, the old programming has been

successfully erased.

To create a new PIN, start with “Setting the PIN for the

First Time”

Mounting Keypad

The keypad MUST be mounted within sight of the

garage door(s) at least  ve feet above the  oor and

clear of any moving door part.

1. Remove battery cover and batteries.

2. Drill 3/32” pilot hole for the top mounting screw

(included).

3. Install a screw into the pilot hole, leaving a 1/8” gap

between the screw head and wall.

4. Hook the slotted mount, on back of keypad, over

the screw.

5. Mark and drill a pilot hole for the bottom screw

(included) and secure keypad to wall (DO NOT

overtighten).

6. Reinstall batteries and cover.

B. Press the chosen HomeLink button for two seconds and release. Press

that same button again for two seconds and release. The long LED

will  ash blue and then turn o .

C. Press the HomeLink button a few more times until door moves.

NOTE:

For additional instructions, see the motor vehicle manual,

www.homelink.com or visit www.geniecompany.com

Step 1 Clear HomeLink

Clear HomeLink by pressing and holding down the  rst and third

buttons until the indicator on the

HomeLink blinks slow and then fast

for 20 seconds; then release both

buttons.

NOTE: Clearing the HomeLink will

remove all previously programmed garage door openers.

Step 2 Train HomeLink to the Remote

Choose the button on the HomeLink that will be used to open

the door.

NOTE:

Hold the Remote two inches

from the HomeLink button.

Hold down the remote button. While holding, press and hold the

chosen HomeLink button.

Hold down both buttons until the indicator on the HomeLink

blinks slow then fast. Once it blinks, release both buttons.

Programming HomeLink® System Programming Car2U

System

Step 1 Clear Car2U to default settings

The default setting for the Car2U system is:

• Button 1 = Genie® Manufactured Openers

• Button 2 = LiftMaster® Manufactured Openers

• Button 3 = Wayne Dalton® Manufactured Openers

A. Press and hold buttons 1 and 3 for 20 seconds or until all three

LEDs begin to  ash.

B. Release both buttons. The Car2U system is now set to the

Factory Default settings

NOTE:

Clearing the Car2U remote will remove all previously

programmed garage door openers.

Step 2 Program Car2U to the Genie® Opener

(Place opener into programming mode)

A. Press and hold the PROGRAM button on the opener

until the round blue LED is ON—release the button.

The long purple LED will begin

 ashing.

B. Press the designated Car2U button for two seconds

and release. Press that same button again for two

seconds and release. The long LED will  ash blue and

then turn o .

C. Press the Car2U button a few times more until door moves.

Step 3 Program HomeLink to the Opener

(Place opener into programming mode)

A. Press and hold the PROGRAM button on the opener until the

round blue LED is ON. Release the button. The long purple

LED will begin  ashing.

Step 3 Changing Factory Default Button for a Genie®

Opener

A. Press and hold buttons 1 & 3 for ONE SECOND and

release—all three LEDs will light solid red.

B. Press and hold the button (2 or 3) to change it to—

the corresponding LED will  ash. While continuing

to hold that button, press and release button 1. Press

and release button 1 again.

C. Release the button being held in step B and wait

for the LED to stop  ashing. This button is now set.

Repeat Step 2 for second Opener.

NOTE:

For additional instructions see the motor vehicle manual,

learcar2u.com.

PROGRAMMING VEHICLE SYSTEMS

1. Press and hold the program button on the powerhead

until the round LED turns blue, then release.

2. The round LED will go out and the long LED will begin

 ashing purple.

3. Complete programming steps.

PUTTING OPENER INTO PROGRAMMING MODE:

NOTE: The openers LEARN LED will time out in 30 seconds.

Programming must be completed within 30 seconds.

1. Press and hold the program button on the powerhead

until the round LED turns blue, then release.

2. The round LED will go out and the long LED will begin

 ashing purple.

3. Complete programming steps.

PUTTING OPENER INTO PROGRAMMING MODE:

NOTE: The openers LEARN LED will time out in 30 seconds.

Programming must be completed within 30 seconds.

PRGM

SET

PRGM

SET

Solid Blue

PRESS

RELEASE

Flashing Purple

PRGM

SET

PRGM

SET

Solid Blue

PRESS

RELEASE

Flashing Purple

Perform these steps only after opener is fully installed, programmed and tested.

To use the Genie Aladdin Connect® app to control this garage door system follow these steps.

Other home automation apps may also control this garage door

opener system. Check our website at www.geniecompany.com for

updates pertaining to compatible 3rd party apps.

AVERTISSEMENT

POUR RÉDUIRE LE RISQUE DE BLESSURES GRAVES

VOIRE MORTELLES, LIRE ET COMPRENDRE TOUTES LES

INSTRUCTIONS.

1. NE JAMAIS laisser les enfants utiliser ou jouer avec les

commandes de l’ouvre-porte.

2. Placer l’étiquette d’AVERTISSEMENT en cas de coinçage à

proximité du bouton mural ou de la console murale de manière à

ce qu’elle soit bien en évidence.

3. NE JAMAIS PASSER SOUS LA PORTE EN MOUVEMENT.

4. NE JAMAIS PASSER SOUS UNE PORTE À L’ARRÊT PARTIELLEMENT

OUVERTE.

5. Le système d’exploitation Aladdin Connect ™ a été conçu pour

fonctionner sans surveillance. La porte peut se déplacer de façon

inattendue.

CONSERVER CES INSTRUCTIONS

CONSIGNES DE SÉCURITÉ IMPORTANTES

The Aladdin Connect® system is a convenient mobile device app to operate up to 20

garage door openers/controllers from anywhere.

The Aladdin Connect® app has the following features:

• Up to 20 users for each account.

• Sends noti cations any time the garage door is operated from the app, wall

console or remote control.

• Show reports for opener usage showing dates and times when the opener

was operated.

• Show reports of who operated the opener when used from another user on

the account.

• Set custom RULES for predetermined times to automatically close a chosen door and/or notify of

its operation.

• Opener light system and an audible signal will activate as a warning that the opener is about to

operate.

WARNING

IMPORTANT SAFETY INSTRUCTIONS

TO REDUCE THE RISK OF SEVERE INJURY OR DEATH, READ

AND FOLLOW ALL INSTRUCTIONS.

1. Never allow children to operate or play with door

controls.

2. Install the entrapment WARNING placard next to the wall

control in a prominent location.

3. NO PERSONS SHOULD CROSS THE PATH OF A MOVING

DOOR.

4. NEVER GO UNDER A STOPPED/PARTIALLY OPEN DOOR.

5. The Aladdin Connect® operating system is designed

for unattended operation. The door could move

unexpectedly.

SAVE THESE INSTRUCTIONS

FOR ALL APPS - Use smart phone or other mobile device to check Wi-Fi signal strength.

Hold the device near the garage door opener and check Wi-Fi meter on the device.

If signal is present, proceed to step 2 if using the Aladdin Connect® app.

Follow manufacturers instructions for other 3rd party apps.

If signal is very week or nonexistent, try the

following:

• Move Wi-Fi router closer to the garage.

• Install a Wi-Fi range extender.

(Available at most electronics stores.)

Check Wi-Fi Signal 1

Genie® Integrated Aladdin Connect® Models

PROGRAMMING TO USE ALADDIN CONNECT®

Scan for iOS app

Apple and the Apple logo are

trademarks of Apple Inc., registered in

the U.S. and other countries. App Store

is a service mark of Apple Inc.

Scan for Android app

Download the Aladdin Connect® app (Unless using 3rd party app)2

Follow steps per the app instructions.

• Create an account

• Set up opener(s)

• Add users

• Set rules and noti cations.

For help at any time contact The Genie Company at 1-866-599-4995 or visit our website.

www.geniecompany.com/aladdinconnect

Scan the Aladdin Connect® QR Code on the front of this

manual or on the powerhead when prompted by the

Aladdin Connect® app.

Follow the Aladdin Connect® app instructions3

NOTE: Use of this product, the software embedded within this product and the related application

software is subject to the Terms and Conditions available at:

www.geniecompany.com/aladdinconnect

Place included unintended operation warning placard next to garage

door openers wall button.

NOTE: This placard should be used in lieu of the standard WARNING placard

included with this opener.

Install WARNING placard4

Versions 8 and higher Versions 4.4 and higher

INSTALLER: LEAVE THIS MANUAL WITH HOMEOWNER

HOMEOWNER: SAVE THIS MANUAL FOR FUTURE REFERENCE

BELT/CHAIN/SCREW DRIVE GARAGE DOOR OPENER

PROGRAMMING, OPERATION & MAINTENANCE MANUAL

39495503881, 03/2018

SERIAL NUMBER DECAL

STOP

DO NOT return product to store,

visit www.GenieCompany.com

or call Customer Service at: 1-800-35-GENIE

iDCM SERIAL NUMBER

To reduce the risk of injury to persons or damage to property, use this opener only with a sectional residential

door.

WARNING

Por reduire le risque de blessures ou de dommages materials, utillsez cet ouvre-porte uniquement pour une porte

a section re sidentielie.

AVERTISSEMENT

Review this manual then refer to the

assembly poster for assembly and

installation instructions. Return to

this manual to program, operate and

maintain the opener.

MAINTENANCE

AVERTISSEMENT

Pour réduire le risque de blessures graves

voire mortelles, lire et comprendre toutes les

instructions.

1. NE JAMAIS permettre aux enfants d’actionner ou de jouer avec les commandes de la porte.

2. Tenir les télécommandes hors de la portée des enfants.

3. TOUJOURS garder en vue la porte en mouvement et tenir à l’écart toute personne ou objet jusqu’à ce que la porte soit

totalement fermée. PERSONNE NE DOIT TRAVERSER LA TRAJECTOIRE D’UNE PORTE EN MOUVEMENT.

4. NE JAMAIS PASSER SOUS UNE PORTE À L’ARRÊT PARTIELLEMENT OUVERTE.

5. Tester l’ouvre-porte une fois par mois. La porte de garage DOIT inverser sa course au contact d’un objet de 4 cm (planche

de 5 sur 10 cm) posé à plat sur le sol au centre de l’ouverture de la porte. Après avoir réglé la force ou la limite de la

course, retenter l’ouvre-porte de garage. Un mauvais réglage de l’ouvre-porte peut entraîner des blessures graves voire

mortelles

6. Utiliser, dans la mesure du possible le déclenchement d’urgence uniquement lorsque la porte est fermée. Utiliser le

déclenchement d’urgence avec prudence lorsque la porte est ouverte. Des ressorts faibles ou brisés peuvent faire

descendre la porte rapidement ce qui peut entraîner des blessures graves voire mortelles.

7. VEILLER À CE QUE LA PORTE SOIT CORRECTEMENT ÉQUILIBRÉE. Consulter le manuel du propriétaire de la porte de

garage. Une porte déséquilibrée pourrait entraîner de graves blessures voire mortelles. Demander à un technicien

spécialisé en système de portes de se charger des réparations des câbles, des ressorts et de toute autre quincaillerie.

CONSERVER CES INSTRUCTIONS

IMPORTANTES CONSIGNES DE SÉCURITÉ

WARNING

To reduce the risk of severe injury or death,

read and follow all instructions.

1. NEVER let children operate or play with the door controls.

2. Keep remote away from children.

3. ALWAYS keep the moving door in sight and away from people and objects until door is completely closed. NO ONE

SHOULD CROSS THE PATH OF THE MOVING DOOR.

4. NEVER GO UNDER A STOPPED, PARTIALLY OPEN DOOR.

5. Test opener monthly. The door MUST reverse on contact with a 1-1/2” high object (or 2” x 4” board laid  at) at the center

of the doorway on the  oor. After adjusting either the force or limit of travel, retest door opener. Failure to adjust the

opener properly may cause severe injury or death.

6. When possible, use emergency release only when door is closed. Use caution when using this release with the door

open. Weak or broken springs are capable of increasing the rate of door closing and increasing the risk of severe injury or

death.

7. KEEP DOORS PROPERLY BALANCED. See your garage door Owner’s Manual. An improperly balanced door increases the

risk of severe injury or death. Have a trained door system technician make repairs to cables, spring assemblies, and other

hardware.

SAVE THESE INSTRUCTIONS

IMPORTANT SAFETY INSTRUCTIONS

L’utilisation d’une autre commande murale pourrait produire des résultats inattendus de la

porte ainsi que le dysfonctionnement de l’éclairage. Localisez la console murale en vue de

la porte et su samment loin de la porte pour éviter tout contact pendant l’utilisation de la

console. La commande doit être à une hauteur minimale de 1,5 m au-dessus du sol a n que les

jeunes enfants ne puissent pas l’atteindre.

VERTISSEMENT

WARNING

Use of any other wall control can cause unexpected operation of the door

and loss of lighting feature. Locate wall console within sight of the door but

far enough from door to prevent contacting it while operating the console.

Control must be at least 5 feet above the  oor to prevent small children from

operating it.

Regular inspection/maintenance for the door and opener should be performed

at regular intervals to ensure the system runs at peak safety, performance and

e ciency.

MAINTENANCE ITEM INTERVALS DETAILS

Contact Reverse Test Monthly See Page 8 to run system test.

Lubricate Door Hardware Monthly Lubricate Rollers & Hinges with a light weight general

purpose grease.

Safe-T-Beam® system check Monthly Check wiring for loose connections, cracks or worn

insulation.

Clean lenses of dirt & debris.

Door Balance Monthly See Maintenance Detail A

Battery Backup System Monthly Unplug opener from outlet. Test opener with remote

or wall console. Replace battery if needed.

Lubricate Screw drive Yearly Use Genie Lube™ to keep screw drive rail operating

smoothly.

Remote Battery replacement As Needed See Maintenance Detail B

Light Bulb Replacement As Needed See Maintenance Detail C

Perform the Door inspection as follows:

With the door closed, pull manual emergency release handle DOWN and away from door and let go to disengage

the carriage from the drive chain or belt. FIG.1.

• Raise and lower the door manually. Door should move freely and smoothly.

• Raise door manually about 3’ to 4’ feet from  oor and let go.

. Door should remain stationary or slowly

drift closed. FIG. 2.

If door opens or closes rapidly, CONTACT A TRAINED DOOR SYSTEM TECHNICIAN to have your door springs

serviced.

• Close the door.

• Place the carriage in the “engage” position Reverse of FIG. 1.

• Operate door using remote or wall control. The carriage will reattach itself to the drive chain/belt.

DO NOT use release cord to pull door!

FIG.1

FIG 2

WARNING

• Garage door hardware (springs, cables, brackets, pulleys, etc.) are under

extreme pressure and tension.

• DO NOT attempt to repair or adjust door springs or any hardware, and

DO NOT OPERATE garage door automatically or manually if door is

improperly balanced or springs are broken.

• CONTACT A TRAINED DOOR SYSTEM TECHNICIAN.

AVERTISSEMENT

• La quincaillerie de la porte de garage (ressorts, câbles, supports, poulies,

etc.) sont sous des pressions et des tensions extrêmes.

• NE PAS réparer ni régler les ressorts de la porte ou toute autre pièce

de quincaillerie et NE PAS ACTIONNER la porte manuellement ou

automatiquement si elle n’est pas correctement équilibrée ou si des ressorts

sont cassés.

• CONTACTEZ UN TECHNICIEN SPÉCIALISÉ EN SYSTÈME DE PORTES

Door Inspection

Screw Drive Chain/Belt Drive

Disengage the carriage by pulling

the release handle straight down,

and then releasing

Disengage the carriage by pulling

the release handle down, toward

the door and then releasing

Remote Battery Replacement (1-button)

Replace remote battery with a CR2032 coin cell battery.

1. Slide the battery cover o .

2. Slide out the old battery and slide in the new. Be sure positive side (+) is UP.

3. Slide the battery cover on until it snaps into place.

Remote Battery Replacement

(3-button)

Replace remote battery with a CR2032 coin cell battery.

1. Open remote case using a washer or coin that  ts into the slot on the top of the remote.

2. Replace battery.

Be sure positive side (+) is UP.

3. Align components and snap case closed.

1. Disconnect power to opener.

2. Open powerhead lens cover by pressing in on upper locking tab and lower cover.

3. Replace old light bulbs with 60 Watt MAXIMUM incandescent, CFL or LED equivalent**.

* Genie LED light bulbs, which are speci cally made for garage door openers, are recommended.

4. Close lens cover.

5. Reconnect power to door opener.

6. Test light operation.

NOTE: Use of standard LED bulbs may reduce the

range of your remote controls*.

WARNING

• Use extreme caution when working from a ladder or step

stool or serious injury can occur.

• When replacing light cover, make sure wires are not pinched

or near moving parts.

• Use only properly rated incandescent, LED or CFL light bulbs.

• DO NOT use bulbs with a rating greater than 60 Watts.

• Use A19 size light bulbs. DO NOT use bulbs having a short

neck.

AVERTISSEMENT

• Faire particulièrement attention lors de travaux e ectués

depuis une échelle ou en escabeau.

• En referment le couvercle de l’éclairage, s’assurer que les  ls

ne sont ni coincés ni près des pièces mobiles.

• Utilisez uniquement incandescence correctement classé, LED

ou des ampoules  uocompactes.

• NE PAS utiliser des ampoules avec une note supérieure à 60

Watts

• Utilisez A19 ampoules de taille. NE PAS utiliser des ampoules

ayant un cou court.

* Genie LED light bulbs are

designed to reduce or eliminate

reduced remote range issues

caused by common LED bulbs.

They also o er better product

life by making them resistant

to vibration caused by the

opener, and cold or damp

weather. See website for details

at www.geniecompany.com.

recommendations for LED bulbs.

**Integrated Aladdin Connect® models require a MINIMUM 40 Watt or equivalent

bulb, 100 watt maximum.

Models equipped with Integrated LED lighting require specialty kits available for

order in the parts section. See page 24.

Replacing Batteries

Changing Light Bulbs (Genie LED bulbs recommended)

PRGM

SET

PRGM

SET

PRGM

SET

Force Settings:

Force settings are pre-programmed at the factory and applied

during the Open/Closed Limit settings steps. For

normal use, these settings should not need adjustment.

Conditions possibly requiring adjustments are:

1. Doors with very sti weather seals.

2. Doors that start down, STOP, and reverse before closing.

3. Doors that start up, but STOP before they completely open.

AVERTISSEMENT

Pour éviter les blessures ou des dommages

• NE JAMAIS régler la force pour compenser des

dommages, y compris une porte mal équilibrée, un rail

de porte coinçant ou des ressorts cassés.

• Tous les mois, EFFECTUEZ LE TEST D’INVERSION AU

CONTACT.

WARNING

TO AVOID INJURY OR DAMAGE

• NEVER adjust the force settings to adjust for damage,

including an unbalanced door, binding door track or

broken spring.

• Perform a CONTACT REVERSE TEST monthly.

1. Press and hold both UP & DOWN arrow buttons until the

ROUND LED turns RED. Release buttons.

• LEDs will show current force level. SEE CHART.

2. Press either the UP or DOWN arrow button until the

desired UP force setting is shown. SEE CHART.

3. Press & release the PRGM button to lock the desired UP

FORCE setting.

• LEDs will now show the current DOWN FORCE setting.

SEE CHART.

4. Press either the UP or DOWN arrow button until desired

DOWN force setting is shown. SEE CHART.

5. Press & release the PRGM button to lock the desired

DOWN FORCE setting.

• Both LEDs will turn BLUE then go out con rming that the

force settings have been changed and are locked.

6. Opener is now ready to operate and test.

7. Operate door from the wall console two full cycles then

perform safety contact reverse test. (SEE PAGE 8)

Flashing

RED

PRESS & RELEASE

See Chart for

Force level

indicators.

Press PRGM to

lock settings

FORCE SETTING CHART

Force Level Long LED Round LED

1 (LOWEST) OFF BLUE

2 BLUE OFF

3 BLUE BLUE

4 OFF VIOLET

5 VIOLET OFF

6 VIOLET VIOLET

7 OFF RED

8 RED OFF

9 (HIGHEST) RED RED

Changing Force Settings

SPECIAL INSTALLATION INFORMATION

NETWORK

CLEARING MEMORY OF ACCESSORIES

NOTE:

Clearing memory of remotes from the powerhead

will clear ALL programmed remotes, wireless keypads and

vehicle transmitters. The opener will no longer recognize

any signal from any remote device, including a missing

remote device. This does not include the Aladdin Connect®

or Wireless Wall Console.

All remaining (or recovered) remotes, vehicles and

wireless keypads MUST be reprogrammed.

NOTE:

The garage door opener will operate normally

using the wall console.

1. Press and hold the SET/PRGM button on the

opener for two seconds.

• The ROUND LED will turn BLUE.

• The ROUND LED will then  ash PURPLE.

2. Press and hold the UP & DOWN buttons at

the same time until both LEDs turn o .

• Both opener LEDs will  ash and turn o

indicating that all remotes have been

erased.

3. Press any remote button.

• The opener should NOT run.

To deprogram the same remote for other garage

door openers, repeat the steps above using one of

the other remaining remote buttons.

1. Enter Programming Mode

Solid Blue Flashing Purple

Flashing

Blue

2. Press and Hold + & - Buttons

3. Test Remote

Release when

LEDs turn o

USE OF DONGLE PORTS - Network & BBU

NOTE:

Dongle ports are used for installing the battery backup (BBU) and Close Con rm® remote controls.

Fully read and understand instructions included with these accessories prior to installation and use.

TO PREVENT POSSIBLE

SERIOUS INJURY or DEATH

from electrocution AND REDUCE RISK of FIRE

— Disconnect ALL electric power sources and battery

power BEFORE performing ANY service or maintenance.

Install only in DRY locations - NOT

INTENDED FOR OUTDOOR USE.

For use ONLY with Genie® model Series 30XX or 40XX Residential

Garage Door Openers.

Use only Genie P/N 36959A for replacement battery.

The Genie Company

Model GBB-BX

CAUTION

PARA EVITAR POSIBLES

LESIONES GRAVES O MUERTE

por electrocución y PARA REDUCIR EL RIESGO DE FUEGO

— Desconecte todas las fuentes de energua eléctrica y la

batería antes de realizar ningún servicio ni mantenimiento.

Instalar sólo en lugares secos — NO ES PARA USO EN EXTERIORES.

Para su uso sólo con Genie® modelo de la serie 30XX o 40XX

abrepuertas residenciales para puertas de garaje.

Utilice sólo Genie® P/N 36959A como batería de repuesto.

The Genie Company

Model GBB-BX

PRECAUCIÓN

37340A

Installez uniquement dans des endroits secs — PAS DESTINE A ETRE

UTILISE EN PLEIN AIR.

A utilizer uniquement avec Genie® modèle de la série 30XX ou 40XX

pour portes de garage résidentielles.

Utilisez uniquement des Genie® P/N 36959A comme batterie

de replacement.

POUR

ÉVIER LES BLESSURES

GRAVES OU LA MORT

par

électrocution et

POUR RÉDUIRE ES RISQUES DE FEU

— Débranches toutes les sources d’alimentation électriques et

la betterie avant toute réparation ou l’entretien.

ATTENTION

The Genie Company

Modèle GBB-BX

NETWORK

BATTERY

BACK-UP

CONNECTION

CABLE

OPERATOR

POWERHEAD

Closed Confirm™

Remote

Network A

dapter

Accessories available at your local supplier of Genie® products.

Remove rubber plug(s) on

NETWORK and/or BBU ports

to install accessory

BBU

La page est en cours de chargement...

Genie 4164 Mode d'emploi

Marque: Genie

Modèle: 4164

Catégorie: Porte de garage

Taper: Mode d'emploi

Ce manuel convient également à

4124

Télécharger le PDF

rapport

dans d''autres langues

English: Genie 4164 Operating instructions

Genie 4164 Mode d'emploi

Ce manuel convient également à

Genie 4164 Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents