Zenoah G2500TS Manuel utilisateur

Marque: Zenoah

Modèle: G2500TS

Catégorie: Tronçonneuses électriques

Taper: Manuel utilisateur

Ce manuel convient également à

Chainsaw G2500TS

OWNER/OPERATOR MANUAL

CHAINSAWS

T2040-93110(010)

The engine exhaust from this product

contains chemicals known to the State

of California to cause cancer, birth

defects or other reproductive harm.

WARNING

Before using our products, please

read this manual carefully to

understand the proper use of your

unit.

WARNING

APPLICABLE SERIAL NUMBERS : 010101 and up

G2500TS

SAFETY FIRST

Instructions contained in warnings within this

manual marked with a symbol concern

critical points which must be taken into

consideration to prevent possible serious

bodily injury, and for this reason you are

requested to read all such instructions

carefully and follow them without fail.

■ WARNINGS IN THE MANUAL

This mark indicates instructions which must be

followed in order to prevent accidents which could

lead to serious bodily injury or death.

This mark indicates instructions which must be

followed, or it leads to mechanical failure,

breakdown, or damage.

This mark indicates hints or directions useful in the

use of the product.

NOTE

IMPORTANT

WARNING

CONTENTS

1. Parts location …………………………………4

2. Specifications …………………………………4

3. Symbols on the machine ……………………5

4. For safe operation ……………………………6

5. Installing guide bar and saw chain …………8

6. Fuel and chain oil……………………………10

7. Operation ……………………………………12

8. Sawing ………………………………………16

9. Maintenance …………………………………19

10. Storage ………………………………………25

11. Troubleshooting guide………………………26

12. Parts list………………………………………27

2. Specifications

■ G2500TS

Power unit :

Dis placement ····················································································· 1.6(25.4) cu-in(cm

)

Fuel ············································································· Mixture(Gasoline 32 : 2-cycle oil 1)

Fuel tank capacity ················································································· 7.78(0.23) fl.oz( )

Chain oil ························································································ Motor oil SAE #10W-30

Oil tank capacity ···················································································· 5.42(0.16) fl.oz( )

Carburetor ································································································· Diaphragm type

lgnition system ··································································································· Solid-state

Spark plug ···························································································· Champion RCJ-7Y

Oil feeding system ····································································· Mechanical plunger pump

Sprocket : Pitch – No. of teeth ··························································· 3/8in(9.38mm) – 6T

Dimensions : L – W – H ············································ 10.4(260)x8.8(220)x8.8(220) in(mm)

Dry weight ································································································ 6.4(2.85) lbs(kg)

Cutting attachment :

Guide bar : Type – Size ····················································· Sprocket nose – 12(30) in(cm)

Saw chain : Type – Pitch – Gauge ···················

Oregon 91VG – 3/8(9.375) – 0.050(1.25) in(mm)

Specifications are subject to change without notice.

1. Parts location

❲

❳

1. Guide Bar

2. Saw Chain

3. Front Guard

4. Front Handle

5. Rear Handle

6. Fuel Tank Cap

7. Oil Tank Cap

3. Symbols on the machine

❲

❳

Made in Japan

RedMax

IMPORTANT ENGINE INFORMATION

THIS ENGINE CONFORMS TO US EPA

PH1 FOR SMALL OFF-ROAD ENGINES.

ENGINE FAMILY : YKZXS.0254DE:EM

ENGINE DISPLACEMENT : 25.4cc

REFER TO OWNER'S MANUMAL FOR MAINTE-

NANCE SPECIFICATIONS AND ADJUSTMENTS.

MANUFACTURED :

INFORMATION IMPORTANTE CONCERNANT LE MOTEUR

Ce moteur conformc aux normcs U.S. EPA

PH1 pour les petits moteurs tout-terrain.

Type de moteur :

YKZXS.0254DE:EM

Cylindrée du moteur :

25.4

Se référer au Manuel de l'utilisateur pour les

spécifications d'entretien et les réglages.

Made in Japan

RedMax

Manufacturé :

For safe operation and maintenance, symbols are carved in relief on

the machine. According to these indications, please be careful not to

make a mistake.

(a).The port to refuel the "MIX GASOLINE"

Position: Upper-front at the left side of the power unit (near the

fuel cap )

(b).The port to refuel the chain oil

Position: Lower-front at the left side of the power unit (near the

oil cap)

(c). Flipping the switch to the "O" position, immediately the engine

stops.

Position: Front at the top of the rear handle (near the switch)

(d).Starting the engine, if you pull out the choke knob (at the back-

right of the rear handle) to the point of the arrow, you can set the

starting mode as follows

• First-stage position – starting mode when the engine is warm.

• Second-stage position – starting mode when the engine is

cool.

Position: Upper-right of the chain cover

(e).If you turn the rod by screwdriver follow the arrow to the "MAX"

position, the chain oil flow more, and if you turn to the "MIN"

position, less.

Position: Bottom of the power unit

(f). The screw under the "H" stamp is The High-speed adjustment

screw.

The screw under the "L" stamp is The Slow-speed adjustment

screw.

The screw at the left of the "T" stamp is the Idle adjustment

screw.

Position: Left side of the rear handle

(g).It shows the directions that the chain brake is released (for the

white arrow) and activated (for the black arrow).

Position: Front of the chain cover

❲

❳

4. For safe operation

1. Never operate a chain saw when you are

fatigued, ill, or upset, or under the

influence of medication that may make

you drowsy, or if you are under the

influence of alcohol or drugs.

2. Use safety footwear, snug fitting clothing

and eye, hearing and head protection

devices.

3. Always use caution when handling fuel.

Wipe up all spills and then move the

chain saw at least ten(10)feet (three(3)

m) from the fueling point before starting

the engine.

3a)Eliminate all sources of sparks or

flame (ie. smoking, open flames, or

work that can cause sparks) in the

areas where fuel is mixed, poured, or

stored.

3b) Do not smoke while handling fuel or

while operating the chain saw.

4. Do not allow other persons to be near

the chain saw when starting the engine

or cutting a wood. Keep bystanders and

animals out of the work area. Children,

pets, and bystanders should be a

minimum of 30feet (10m) away when

you start or operate the chain saw.

5. Never start cutting until you have a clear

work area, secure footing, and planned

retreat path from the falling tree.

6. Always hold the chain saw firmly with

both hands when the engine is running.

Use a firm grip with thumb and fingers

encircling the chain saw handles.

7. Keep all parts of your body away from

the saw chain when the engine is

running.

8. Before you start the engine, make sure

the saw chain is not contacting anything.

9. Always carry the chain saw with the

engine stopped, the guide bar and saw

chain to the rear, and the muffler away

from your body.

10. Always inspect the chain saw before

each use for worn, Ioose, or changed

parts. Never operate a chain saw that is

damaged, improperly adjusted, or is not

completely and securely assembled. Be

sure that the saw chain stops moving

when the throttle control trigger is

released.

11. All chain saw service, other than the

items listed in the Operator’s Manual,

should be performed by competent chain

saw service personnel. (e.g., if improper

tools are used to remove the flywheel, or

if an improper tool is used to hold the

flywheel in order to remove the clutch,

structural damage to the flywheel could

occur which could subsequently cause

the flywheel to disintegrate).

12. Always shut off the engine before setting

it down.

13. Use extreme caution when cutting small

size brush and saplings because slender

material may catch the saw chain and be

whipped toward you or pull you off

balance.

14.When cutting a limb that is under

tension, be alert for spring back so that

you will not be struck when the tension in

the wood fibers is released.

15. Keep the handles dry, clean and free of

oil or fuel mixture.

❲

❳

4. For safe operation

16.Operate the chain saw only in well

ventilated areas. Never start or run the

engine inside a closed room or building.

Exhaust fumes contain dangerous

carbon monoxide.

17. Do not operate a chain saw in a tree

unless specially trained to do so.

18. Guard against kickback. Kickback is the

upward motion of the guide bar which

occurs when the saw chain at the nose

of the guide bar contacts an object.

Kickback can lead to dangerous loss of

control of the chain saw.

19. When transporting your chain saw, make

sure the appropriate guide bar scabbard

is in place.

20. This chain saw is equipped with a spark

arrester built-in muffler. Periodically

check the arrester to keep it in good

order.

KICKBACK SAFETY PRECAUTIONS FOR

CHAIN SAW USERS

– WARNING –

● Kickback may occur when the nose or tip of the guide bar touches an object, or when the

wood closes in and pinches the saw chain in the cut. Tip contact in some cases may

cause a lightning fast reverse reaction, kicking the guide bar up and back towards the

operator. Pinching the saw chain along the top of the guide bar may push the guide bar

rapidly back towards the operator. Either of these reactions may cause you to lose

control of the saw which could result in serious personal injury.

● Do not rely exclusively on the safety devices built into your saw. As a chain saw user you

should take several steps to keep cutting jobs free from accident or injury.

(1) With a basic understanding of kickback you can reduce or eliminate the element of

surprise. Sudden surprise contributes to accidents.

(2) Keep a good grip on the saw with both hands, the right hand on the rear handle, and

the left hand on the front handle, when the engine is running. Use a firm grip with

thumbs and fingers encircling the chain saw handles. A firm grip will help you reduce

kickback and maintain control of the saw. Don’t let go.

(3) Make certain that the area in which you’re cutting is free from obstructions. Do not let

the nose of the guide bar contact a log, branch, or any other obstruction which could

be hit while you are operating the saw.

(4) Cut at high engine speeds.

(5) Do not overreach or cut above shoulder height.

(6) Follow manufacturers sharpening and maintenance instructions for saw chain.

(7) Only use replacement bars and chains specified by the manufacturer or the

equivalent.

A standard saw unit package contains the items as

shown below. (SE1)

(1)Power unit

(2)Guide bar

(3)Saw chain

(4)Plug wrench

Open the box and install the guide bar and the saw

chain on the power unit as follows.

The saw chain has very sharp edges. Use

protective gloves for safety.

1. Pull the guard towards the front handle to check

that the chain brake is not on.

2. Loosen a nut and remove the chain cover.

3. Fix the hanger on the rear of power unit by

screw. (SE2)

(1)Hanger

4. Mount the guide bar then fit the saw chain

around the bar and sprocket.(SE3)

Pay attention to the correct direc-tion of the

saw chain

5. Fit the chain tensioner nut into the lower hole of

the guide bar, then install the chain cover, and

fasten the mounting nut to finger tightness.

(SE3)(SE4)

(1)Hole

(2)Moving direction

(3)Chain tensioner nut

When installing the chain cover, be sure to fit

the hook completely at the rear end of the

cover.

WARNING

5. Installing guide bar and saw chain

❲

❳

SE1

SE2

SE3

SE4

5. Installing guide bar and saw chain

❲

❳

SE5

SE6

6. While holding up the tip of the bar,adjust the

chain tension by turning the tensioner screw until

the tie straps just touch the bottom side of the

bar rail. (SE5)

(1)Chain tension adjusting screw

(a)Loosen

(b)Tighten

7. Tighten the mounting nut securely with the bar

tip held up (TORQUE: 11.8~14.7 N.m./120~150

kg-cm). Then check the chain for smooth

rotation and correct tension while moving it by

hand. If necessary, readjustment. (SE6)

(1)Tighten

It is very important to maintain the proper chain

tension. Rapid wear of the guide bar or the

chain coming off easily can be caused by

improper tension. Especially when using a new

chain, take good care of it since it should

expand when first used.

WARNING

❲

❳

6. Fuel and chain oil

■ FUEL

The RedMax engines are lubricated by oil specially

formulated for air-cooled 2-cycle gasoline engine

use. If RedMax oil is not available, use an anti-

oxidant added quality oil expressly labeled for air-

cooled 2-cycle engine use.

RECOMMENDED MIXING RATIO

GASOLINE 32 : OIL 1

Exhaust emission are controlled by the

fundamental engine parameters and

components (eq., carburation, ignition timing

and port timing) without addition of any major

hardware or the introduction of an inert

material during combustion.

These engines are certified to operate on

unleaded gasoline.

The fuel is highly flammable. Do not smoke or

bring any flame or sparks near fuel.

■ HOW TO MIX FUEL

1. Measure out the quantities of gasoline and oil to

be mixed.

2. Put some of the gasoline into a clean, approved

fuel container.

3. Pour in all of the oil and agitate well.

4. Pour in the rest of gasoline and agitate again for

at least one minute.

5. Put a clear indication on the outside of the

container to avoid mixing up with gasoline or

other containers.

FOR YOUR ENGINE LIFE, AVOID;

1. FUEL WITH NO OIL(RAW GASOLINE) – It will

cause severe damage to the engine inner parts

very quickly.

2. GASOHOL – It can cause deterioration of rubber

and/or plastic parts and disruption of engine

lubrication.

3. OIL FOR 4-CYCLE ENGINE USE or WATER

COOLED 2-CYCLE ENGINE USE – It can

cause spark plug fouling, exhaust port blocking,

or piston ring sticking.

WARNING

6. Fuel and Chain oil

■ CHAIN OIL

Use motor oil SAE 10W-30 all year round, or SAE

30-40 in summer and SAE 20 in winter.

Do not use waste or regenerated oil that can cause

damage to the oil pump.

NOTE

❲

❳

❲

❳

■ STARTING ENGINE

1. Feed fuel and chain oil into their respective

tanks and tighten the caps securely. (OP1)

(1)Fuel

(2)Chain oil

2. Continuously push the priming bulb until fuel

comes in the bulb. (OP2)

3. Put the switch to the "I" position. (OP3)

(1)Switch

4. Pull out the choke knob to the second-stage

position. The choke will close and the throttle

lever will then be set in the starting position.

(OP4,5)

(1)Throttle lever

(2)Throttle interlock

(3)Choke knob

(a)when the engine is cool

(b)when the engine is warm up

(c)after the engine starts

When restarting immediately after stopping the

engine. Choke knob in the first-stage position

(choke open and throttle lever in the starting

position)

NOTE

7. Operation

OP1

OP2

OP3

OP4

OP5

OP8

7. Operation

Once the choke knob has been pulled out, it will

not return to the operating position even if you

press down on it with your finger. When you wish

to return the choke knob to the operating position,

pull out the throttle lever instead.

5. While holding the saw unit securely on the

ground, pull the starter rope vigorousl y. (OP6)

6. When firing occur, push in the choke knob and

pull the starter again to start the engine.

7. Allow the engine to warm up with the throttle

lever pulled slightly.

Before you start the engine, make sure the saw

chain is not contacting anything.

■ CHECKING OIL SUPPLY

After starting the engine, run the chain at medium

speed and see if chain oil is scattered off as shown

in the figure. (OP7)

(1)Chain oil

The chain oil flow can be changed by inserting a

screwdriver in the hole on bottom of the clutch

side. Adjust according to your work conditions.

(OP8)

(1)Chain oil flow adjusting shaft

(a)Rich

(b)Lean

The oil tank should become nearly empty by the

time fuel is used up. Be sure to refill the oil tank

every time when refueling the saw.

NOTE

WARNING

NOTE

OP6

OP7

❲

❳

❲

❳

■ ADJUSTING CARBURETOR (OP9)

The carburetor on your unit has been factory

adjusted, but may require fine tuning due to

change in operating conditions.

Before adjusting the carburetor, make sure that

provided are clean air/fuel filters and fresh,

properly mixed fuel.

When adjusting, take the following steps:

Be sure to adjust the carburetor with the bar chain

attached.

1. H and L needles are restricted within the number

of turn as shown below.

H needle –1/4

L needle –1/4

2. Start engine and allow it to warm up in low

speed for a few minutes.

3. Turn idle adjusting screw (T) counter-clockwise

so that saw chain does not turn. If idling speed is

too slow, turn the screw clockwise.

4. Make a test cut adjust the H needle for best

cutting power, not for maximum speed.

(1)L needle

(2)H needle

(3)Idle adjusting screw

■ CHAIN BRAKE (OP10)

The chain brake is a device which stops the chain

instantaneously if the chain saw recoils due to

kickback.

Normally, the brake is activated automatically by

inertial force. It can also be activated manually by

pushing the brake lever (left-hand guard) down

toward the front.

When the brake operates, a yellow cone pops up

from the base of the brake lever.

Releasing the Brake

Pull the brake lever up toward the left-hand handle

until it clicks into place.

NOTE

7. Operation

OP9

❲

❳

7. Operation

OP10

OP11

• When the brake operates, release the throttle

lever to slow down the engine speed.

Continuous operation with the brake

engaged will generate heat from the clutch

and may cause trouble.

• At machine inspection prior to each job,

check the operating condition of the brake

following the steps below.

1. Start the engine and grasp the handle securely

with both hands.

2. Pulling the throttle lever to maintain the chain

operation, push the brake lever (left-hand guard)

down toward the front using the back of your left

hand.

3. When the brake operates and the chain is

stopped, release the throttle lever.

4. Release the brake.

(1)Releases the brake.

(2)Activates the brake.

■ STOPPING ENGINE

1. Release the throttle lever to allow the engine

idling for a few minutes

2. Put the switch to the "O" position. (OP11)

(1)Switch

WARNING

❲

❳

8. Sawing

SA1

• Before proceeding to your job, read "For

Safe Operation" section It is recommended

to first practice sawing easy logs. This also

helps you get accustomed to your unit.

• Always follow the safety regulations. The

chain saw must only be used for cutting

wood. It is forbidden to cut other types of

material. Vibrations and kickback vary with

different materials and the requirements of

the safety regulations would not be

respected. Do not use the chain saw as a

lever for lifting, moving or splitting objects.

Do not lock it over fixed stands. It is

forbidden to hitch tools or applications to the

P.t.o. that are not specified by the

manufacturer.

• It is not necessary to force the saw into the

cut. Apply only light pressure while running

the engine at full throttle.

• When the saw chain is caught in the cut, do

not attempt to pull it out by force, but use a

wedge or a lever to open the way.

■ Guard against kickback (SA1)

• This saw is equipped with a chain brake that will

stop the chain in the event of kickback if

operating properly. You must check the chain

brake operation before each usage by running

the saw at full the throttle for I -2 seconds and

pushing the front hand guard forward. The chain

should stop immediately with the engine at full

speed. If the chain is slow to stop or does not

stop, replace the brake band and clutch drum

before use.

• It is extremely important that the chain brake be

checked for proper operation before each use

and that the chain be sharp in order to maintain

the kickback safety level of this saw. Removal of

the safety devices, inadequate maintenance, or

incorrect replacement of the bar or chain may

increase the risk or serious personal injury due

to kickback.

WARNING

SA3

■ FELLING A TREE (SA2)

When you fell a tree, be sure to warn your

neighboring workers of the danger.

1. Decide the felling direction considering the

wind, Iean of the tree, location of heavy

branches, ease of job after felling, and

other factors .

2. While clearing the area around the tree,

arrange a good foothold and retreat path.

3. Make a notch cut one-third of the way into

the tree on the felling side.

4. Make a felling cut from the opposite side

of the notch and at a level slightly higher

than the bottom of the notch.

■ LOGGING AND LIMBING

1. Always ensure your foothold as well as

stability of the tree.

2. Be alert to the rolling over of a cut log.

3. Read the instructions in “For safe

operation” to avoid kickback of the

saw.

Before starting work, check the direction of

bending force inside the log to be cut.

Always finish cutting from the opposite side

of bending direction to prevent the guide bar

from being caught in the cutaway.

● Cutting an unpillowed log

Saw down halfway, then roll the log over and

cut from the opposite side. (SA3)

WARNING

8. Sawing

SA2

❲

❳

❲

❳

● Cutting a pillowed log

In the area A in the picture right above, saw up

from the bottom one-third and finish by sawing

down from the top. In the area B, saw down from

the top one-third and finish by sawing up from the

bottom. (SA4)

● Limbing a felled tree

Be alert to the spring back of a cut limb.

First check which way the limb is bent. Then make

a shallow cut into the compressed side to prevent

the limb from being torn. Cut through from the

tensed side. (SA5)

● Pruning

1. Do not use an unstable foothold or a

stepladder.

2. Do not overreach.

3. Do not cut above shoulder height.

4. Always use both hands to grip the saw.

Cut up from the bottom, finish down from the top.

(SA6)

WARNING

8. Sawing

SA4

SA5

SA6

9. Maintenance

Make sure the engine is stopped .

■ DAILY CHECK POINTS

1. Air filter

Loosen the knob and remove the air cleaner cover.

Take off the filter elements and tap off attached

sawdust. When they are extremely dirty,

shakewash with gasoline. Dry them completely

before reinstalling. (MA1)

2. Oiling port

Dismount the guide bar and check the oiling port

for clogging. (MA2)

(1)Oiling port

3. Guide bar

Remove sawdust in the bar groove and the oiling

port. (MA3)

(1)Groove

(2)Oiling port

(Type: Sprocket nose)

Grease the nose sprocket from the feeding port on

the tip of the bar. (MA4)

(1)Grease port

(2)Sprocket

4. Others

Check for fuel leakage and loose fastenings or

damage to major parts, especially handle joints

and guide bar mounting. If any defects are found,

make sure to have them repaired before operating

again

WARNING

MA1

MA4

MA3

MA2

❲

❳

❲

❳

9. Maintenance

This saw is equipped with one of the following

low kickback bar/chain combinations:

RedMax Part Number

Bar Size Guide Bar Saw Chain

12inch (30cm) G2512 91VG45X

For replacement, use only above bar and chain,

or the following;

OREGON BAR

12 inch S/N DOUBLE GUARD BAR,

Mount code #A041. (120 SDEA 041)

GB BAR

12 inch MINI LAMINATED BAR (PO12-50CR)

OREGON CHAIN

91VG

■ PERIODICAL CHECK POINTS

1. Cylinder fins

1. Remove the starter case.

2. Remove sawdust between the cylinder fins.

(MA5)

(1)Cylinder fin

2. Fuel filter

1. Using a wire hook, take out the fuel filter from

the feeding port. (MA6)

2. Wash the filter with gasoline.

Replace with new one if clogged with dirt

completely.

When returning the filter, use a pinch not to be

folded the suction pipe.

3. Oil filter

1. With a wire hook, take out the oil filter from

the feeding port. (MA7)

2. Wash the filter with gasoline.

WARNING

MA7

MA6

MA5

La page charge ...

Zenoah G2500TS Manuel utilisateur

Marque: Zenoah

Modèle: G2500TS

Catégorie: Tronçonneuses électriques

Taper: Manuel utilisateur

Ce manuel convient également à

Chainsaw G2500TS

Télécharger le PDF

rapport

dans d''autres langues

English: Zenoah G2500TS User manual

Zenoah G2500TS Manuel utilisateur

Ce manuel convient également à

Zenoah G2500TS Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents