Troy-Bilt TB320BV Manuel utilisateur

Marque: Troy-Bilt

Modèle: TB320BV

Catégorie: Souffleurs / sécheurs d'air

Taper: Manuel utilisateur

Ce manuel convient également à

Vacuum Cleaner TB320BV

Operator’s Manual

2-Cycle Mulching

Blower / Vacuum

Model TB320BV

P/N 769-01308 (6/04)

PRINTED IN USA

SAVE THESE INSTRUCTIONS DO NOT THROW AWAY

INTRODUCTION

Copy the serial number

here:

THANK YOU

Thank you for buying this quality product. This modern

outdoor power tool will provide many hours of useful

service. You will find it to be a great labor-saving device.

This operator’s manual provides you with easy-to-

understand operating instructions. Read the whole

manual and follow all the instructions to keep your new

outdoor power tool in top operating condition.

PRODUCT REFERENCES, ILLUSTRATIONS

AND SPECIFICATIONS

All information, illustrations, and specifications in this

manual are based on the latest product information

available at the time of printing. We reserve the right to

make changes at any time without notice.

Reserved.

SERVICE INFORMATION

Service on this unit both within and after the warranty

period should be performed only by an authorized and

approved service dealer.

For service call 1-800-520-5520 to obtain a list of

authorized service dealers near you. For more details

about your unit, visit our website at www.troybilt.com.

DO NOT RETURN THE UNIT TO THE RETAILER.

PROOF OF PURCHASE WILL BE REQUIRED FOR

WARRANTY SERVICE.

Before beginning, locate the unit’s model plate. It lists

the model and serial numbers of your unit. Refer to the

sample plate below and copy the information for future

reference.

S/N :

ITEM :

MODEL :

Make sure you carefully read and understand this manual

before starting or operating this equipment.

THIS PRODUCT IS COVERED BY ONE OR MORE U.S.

PATENTS. OTHER PATENTS PENDING.

TABLE OF CONTENTS

Service Information . . . . . . . . . . . . . . . . . . . . . . . . .2

Rules for Safe Operation . . . . . . . . . . . . . . . . . . . . .3

Know Your Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

Assembly Instructions . . . . . . . . . . . . . . . . . . . . . . .8

Oil and Fuel Information . . . . . . . . . . . . . . . . . . . . .11

Starting/Stopping Instructions . . . . . . . . . . . . . . . .12

Operating Instructions . . . . . . . . . . . . . . . . . . . . . .13

Maintenance and Repair Instructions . . . . . . . . . . .15

Cleaning and Storage . . . . . . . . . . . . . . . . . . . . . . .18

Accessories and Replacement Parts . . . . . . . . . . .18

Troubleshooting Chart . . . . . . . . . . . . . . . . . . . . . .19

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

Warranty Information . . . . . . . . . . . . . . . . . . . . . . .22

Parts List . . . . . . . . . . . . . . . . . . . .Inside Back Cover

Copy the model and parent

part number here:

SPARK ARRESTOR NOTE

NOTE: For users on U.S. Forest Land and in the

states of California, Maine, Oregon and Washington.

All U.S. Forest Land and the state of California (Public

Resources Codes 4442 and 4443), Oregon and

Washington require, by law that certain internal

combustion engines operated on forest brush and/or

grass-covered areas be equipped with a spark arrestor,

maintained in effective working order, or the engine be

constructed, equipped and maintained for the prevention

of fire. Check with your state or local authorities for

regulations pertaining to these requirements. Failure to

follow these requirements could subject you to liability or

a fine. This unit is factory equipped with a spark

arrestor. If it requires replacement, ask your LOCAL

SERVICE DEALER to install the Accessory Part

#182747 Spark Arrestor Kit.

CALIFORNIA PROPOSITION 65 WARNING

WARNING

THE ENGINE EXHAUST FROM THIS

PRODUCT CONTAINS CHEMICALS

KNOWN TO THE STATE OF CALIFORNIA

TO CAUSE CANCER, BIRTH DEFECTS

OR OTHER REPRODUCTIVE HARM.

READ ALL INSTRUCTIONS

BEFORE OPERATING

• Read the instructions carefully. Be familiar with the

controls and proper use of the unit.

• Do not operate this unit when tired, ill, or under the

influence of alcohol, drugs, or medication.

• Children and teens under the age of 15 must not use

the unit, except for teens guided by an adult.

• All guards and safety attachments must be installed

properly before operating the unit.

• Inspect the unit before use. Replace damaged parts.

Check for fuel leaks. Make sure all fasteners are in

place and secure. Replace parts that are cracked,

chipped, or damaged in any way. Do not operate the

unit with loose or damaged parts.

• Carefully inspect the area before starting the unit.

Remove all debris and hard or sharp objects such as

glass, wire, etc.

• Clear the area of children, bystanders, and pets. At a

minimum, keep all children, bystanders, and pets

outside a 50 feet (15 m.) radius; there still may be a

risk to bystanders from thrown objects. Bystanders

should be encouraged to wear eye protection. If you

are approached, stop the unit immediately.

SAFETY WARNINGS FOR GAS UNITS

• Store fuel only in containers specifically designed and

approved for the storage of such materials.

• Avoid creating a source of ignition for spilled fuel. Do

not start the engine until fuel vapors dissipate.

• Always stop the engine and allow it to cool before filling

the fuel tank. Never remove the cap of the fuel tank, or

add fuel, when the engine is hot. Never operate the unit

without the fuel cap securely in place. Loosen the fuel

tank cap slowly to relieve any pressure in the tank.

• Mix and add fuel in a clean, well-ventilated outdoor area

where there are no sparks or flames. Slowly remove the

fuel cap only after stopping engine. Do not smoke while

fueling or mixing fuel. Wipe up any spilled fuel from the

unit immediately. Always wipe unit dry before using.

• Move the unit at least 30 feet (9.1 m) from the fueling

source and site before starting the engine. Do not

smoke or allow sparks and open flames near the area

while adding fuel or operating the unit.

RULES FOR SAFE OPERATION

SYMBOL MEANING

The purpose of safety symbols is to attract your

attention to possible dangers. The safety symbols,

and their explanations, deserve your careful attention

and understanding. The safety warnings do not by

themselves eliminate any danger. The instructions or

warnings they give are not substitutes for proper

accident prevention measures.

NOTE: Advises you of information or instructions vital to

the operation or maintenance of the equipment.

SYMBOL MEANING

When using the unit,

you must follow the

safety rules. Please read these instructions

before operating the unit in order to ensure

the safety of the operator and any bystanders.

Please keep these instructions for later use.

WARNING:

• IMPORTANT SAFETY INSTRUCTIONS •

Failure to obey a

safety warning can

result in injury to yourself and others.

Always follow the safety precautions to

reduce the risk of fire, electric shock and

personal injury.

WARNING:

Failure to obey a

safety warning will

result in serious injury to yourself or to

others. Always follow the safety precautions

to reduce the risk of fire, electric shock and

personal injury.

DANGER:

Failure to obey a

safety warning may

result in property damage or personal injury

to yourself or to others. Always follow the

safety precautions to reduce the risk of fire,

electric shock and personal injury.

CAUTION:

Indicates

danger,

warning or caution. Attention is required in

order to avoid serious personal injury. May

be used in conjunction with other symbols

or pictographs.

SAFETY ALERT:

Gasoline is highly

flammable, and its

vapors can explode if ignited. Take the

following precautions:

WARNING:

Read the Operator’s Manual(s) and follow all

warnings and safety instructions.

Failure to do so can result in serious injury to the

operator and/or bystanders.

FOR QUESTIONS, CALL 1-800-520-5520

RULES FOR SAFE OPERATION

WHILE OPERATING

• Never start or run the unit inside a closed room or

building. Breathing exhaust fumes can kill. Operate this

unit only in a well-ventilated outdoor area.

• To reduce the risk of injury associated with thrown

objects, wear safety glasses or goggles that are

marked as meeting ANSI Z87. standards.

• Never run the unit without the the proper equipment

attached. When using this unit, always install the

blower/vacuum tubes and vacuum bag depending on

model. Make sure the vacuum bag is completely

zipped closed.

• To reduce the risk of hearing loss associated with

sound level(s), always wear ear/hearing protection

when operating this unit.

• Wear heavy, long pants, boots, and gloves. Do not

wear short pants, sandals, or go barefoot.

• To avoid static electricity shock, do not wear rubber

gloves or any other insulated gloves while operating

this unit.

• To reduce the risk of injury associated with objects

being drawn into rotating parts, do not wear loose

clothing, jewelry, scarves, and the like. Secure hair

above shoulder level.

•Wear a face or dust mask if the operation is dusty.

Long sleeve shirts are recommended.

• Use the unit only in daylight or good artificial light.

• Keep outside surfaces free from oil and fuel.

• Avoid accidental starting. Be in the starting position

whenever pulling the starter rope. The operator and

unit must be in a stable position while starting. Refer to

Starting/Stopping Instructions.

• Do not set unit on any surface except a clean, hard

area while engine is running. Debris such as gravel,

sand, dust, grass, etc. could be picked up by the air

intake and thrown out by the discharge opening,

damaging unit, property, or causing serious injury to

bystanders or operator.

• Use the right tool. Only use this tool for the purpose

intended.

• Do not force unit. It will do the job better and with less

likelihood of injury at a rate for which it was designed.

• Do not overreach or use from unstable surfaces such

as ladders, trees, steep slopes, rooftops, etc. Always

keep proper footing and balance.

• Always hold the unit with a firm grip when operating.

• Keep hands, face, and feet at a distance from all moving

parts. Do not touch or try to stop the impeller when it is

rotating. Do not operate without guards in place.

• Do not put any object into openings. Do not use with

any opening blocked; keep free of dirt, debris, and

anything that may reduce the air flow.

• Do not touch the engine or muffler. These parts get

extremely hot from operation. When turned off they

remain hot for a short time.

• Do not operate the engine faster than the speed

needed to do the job. Do not run the engine at high

speed when not in use.

• Always stop the engine when operation is delayed or

when walking from one location to another.

• Stop the engine for maintenance, repair, to install or

remove the blower tubes or vacuum attachments. The

unit must be stopped and the impeller no longer

turning to avoid contact with the rotating blades.

• Use only original equipment manufacturer replacement

parts when servicing this unit. These parts are available

from your authorized service dealer. Do not use

unauthorized parts, accessories, or attachments for

this unit. Doing so could lead to serious injury to the

user, or damage to the unit, and void your warranty.

• Never use this unit for spreading chemicals, fertilizers or

other substances which may contain toxic materials.

•To reduce fire hazard, replace faulty muffler and spark

arrestor, keep the engine and muffler free from grass,

leaves, excessive grease or carbon build up.

WHILE OPERATING UNIT AS A BLOWER

• Never point the blower in the direction of people or

pets, or in the direction of windows. Always direct the

blowing debris away from people, animals, and

windows. Use extra caution when blowing debris near

solid objects such as trees, automobiles, walls, etc.

WHILE OPERATING UNIT AS A VACUUM

• Avoid situations that could catch the vacuum bag on

fire. Do not operate near an open flame. Do not

vacuum warm ash from fireplaces, barbecue pits,

brush piles, etc. Do not vacuum discarded cigars or

cigarettes unless the cinders are completely cool.

• The unit is designed to pickup dry material such as

leaves, grass, small twigs, and bits of paper. Do not

attempt to vacuum wet debris and/or standing water

as this may result in damage to the blower/ vacuum.

To avoid severe damage to the impeller, do not

vacuum metal, broken glass, etc.

OTHER SAFETY WARNINGS

• Always disconnect the spark plug before performing

maintenance or accessing movable parts.

• Never store the unit, with fuel in the tank, inside a

building where fumes may reach an open flame (pilot

lights, etc.) or sparks (switches, electrical motors, etc.).

• Allow the engine to cool before storing or transporting.

Be sure to secure the unit while transporting.

• Store the unit in a dry place, either locked up or up

high to prevent unauthorized use or damage. Keep out

of the reach of children.

• Never douse or squirt the unit with water or any other

liquid. Keep handles dry, clean, and free from debris.

Clean after each use, see Cleaning and Storage

instructions.

• Keep these instructions. Refer to them often and use

them to instruct other users. If you loan this unit to

others, also loan these instructions to them.

SPECIAL NOTE: Exposure to vibrations through

prolonged use of gasoline powered hand tools could

cause blood vessel or nerve damage in the fingers,

hands, and joints of people prone to circulation disorders

or abnormal swelling. Prolonged use in cold weather has

been linked to blood vessel damage in otherwise healthy

people. If symptoms occur such as numbness, pain, loss

of strength, change in skin color or texture, or loss of

feeling in the fingers, hands or joints, discontinue use of

this tool and seek medical attention. An anti-vibration

system does not guarantee avoidance of these

problems. Users who operate power tools on a regular

basis must closely monitor their physical condition and

the condition of this tool.

SAVE THESE INSTRUCTIONS

RULES FOR SAFE OPERATION

SYMBOL MEANING

• SAFETY ALERT SYMBOL

Indicates danger, warning, or

caution. May be used in conjunction

with other symbols or pictographs.

• WARNING - READ OPERATOR'S

MANUAL

Read the Operator’s Manual(s) and

follow all warnings and safety

instructions. Failure to do so can

result in serious injury to the

operator and/or bystanders.

• WEAR EYE AND HEARING

PROTECTION

WARNING: Thrown objects and

loud noise can cause severe eye

injury and hearing loss. Wear eye

protection meeting ANSI Z87.1-1989

standards and ear protection when

operating this unit.

Use a full face

shield when needed.

• UNLEADED FUEL

Always use clean, fresh unleaded fuel.

• OIL

Refer to operator's manual for the

proper type of oil.

• THROWN OBJECTS AND

ROTATING CUTTER CAN CAUSE

SEVERE INJURY

WARNING: Keep clear of blower

outlet. Never point the blower at

yourself or others. Objects can be

thrown from blower. Do not operate

unit without proper attachments and

guards in place.

SAFETY AND INTERNATIONAL SYMBOLS

This operator's manual describes safety and international symbols and pictographs that may appear on this product.

Read the operator's manual for complete safety, assembly, operating and maintenance and repair information.

SYMBOL MEANING

•ON/OFF STOP CONTROL

ON / START / RUN

•ON/OFF STOP CONTROL

OFF OR STOP

• HOT SURFACE WARNING

Do not touch a hot muffler or

cylinder. You may get burned. These

parts get extremely hot from

operation. When turned off they

remain hot for a short time.

• BLOWERS – ROTATING

IMPELLER BLADES CAN

CAUSE SEVERE INJURY

WARNING: Stop the engine and

allow the impeller to stop before

opening the vacuum door, installing

or changing tubes or bag, or before

cleaning or performing any

maintenance.

• THROTTLE CONTROL

Indicates “HIGH” or “FASTEST” speed.

• THROTTLE CONTROL

Indicates “IDLE,” “LOW” or

“SLOWEST” speed.

• KEEP BYSTANDERS AWAY

WARNING: Keep all bystanders,

especially children and pets, at least

50 feet (15 m.) from the operating area.

RULES FOR SAFE OPERATION

APPLICATION

As a blower:

• Cleaning yards, garages, driveways, porches,

patios, around walls, fences and more

As a vacuum:

• Picking up leaves and other light debris

Blower Tube

Vacuum Bag

Blower

Outlet

Vacuum Bag

Zipper

Fuel Cap

Throttle Control

Primer

Bulb

Blue EZ-Start Lever

Air filter/muffler cover

Spark Plug

Starter Rope

Grip

On/Off Stop

Control

KNOW YOUR UNIT

Muffler

Assembled as a Blower

Assembled as a Vacuum

Vacuum

Door

Front Handle

Vacuum Inlet

Vacuum

Tube

Rear Handle

Vacuum

Bag Hook

ASSEMBLY INSTRUCTIONS

ASSEMBLING UNIT AS A BLOWER

Blower Tube Assembly

NOTE: If the unit was assembled as a vacuum unit,

remove all vacuum parts and store away in a

secure place for later use.

Installing

• Install the blower tube over the blower outlet and push

it on until both tabs snap into place (Fig. 1).

Removing

• Remove the blower tube by pressing both tabs at the

same time and pulling off the blower (Fig. 1).

ASSEMBLING UNIT AS A VACUUM

To assemble the unit as a vacuum, begin by removing

the blower tube. Refer to the previous section.

Vacuum Tube Assembly

NOTE: If the unit was assembled as a blower unit,

remove the blower tube and store away in a

secure place for later use.

Installation

1. Align the small arrow on the lower vacuum tube with

the arrow on the upper vacuum tube (Fig. 2).

2. Grasp the lower and upper vacuum tubes firmly with

both hands, and push the lower vacuum tube into

the upper vacuum tube. Turn the lower vacuum tube

clockwise until it snaps into detente and locks. When

properly assembled, the dot on the lower tube aligns

with the dot on the upper tube.

3. Flip the unit so it is standing straight up on the

muffler cover. The front of the unit and the vacuum

door should face you (Fig. 3).

Fig. 1

Fig. 2

Fig. 3

Tabs

Vacuum

Door

Blower

Outlet

Upper Vac Tube

Lower Vac Tube

To prevent serious

personal injury, stop

the engine and allow the impeller to stop

before attaching or removing tubes.

WARNING:

To prevent serious

personal injury or

damage to the unit, the blower tube must

be installed while operating this unit as a

blower.

WARNING:

To prevent serious

personal injury, stop

the engine and allow the impeller to stop

before attaching or removing tubes.

WARNING:

To prevent serious

personal injury or

damage to the unit, always install vacuum

tubes and the vacuum bag, and make sure

the vacuum bag is completely zipped closed

when operating this unit as a vacuum.

WARNING:

ASSEMBLY INSTRUCTIONS

4. Insert a flat head screwdriver into the slot at the

lower end of the vacuum door. Make contact with

the vacuum door locking clip and push inward and

upwards (Fig. 4). Then pull the vacuum door and

hold it open.

5. While holding the vacuum door open, locate the

assembled vacuum tube (put together in Step 2).

Arrange the tube so the flat area faces the vacuum

door. The grooves on the side of the tube will line up

with the small tabs in the impeller intake (Fig. 5).

From the exterior, align the small arrow on the

vacuum tube with the arrow on the impeller intake.

6. Push the vacuum tube in firmly and grip it with both

hands. Turn the tube clockwise as far as possible

until it snaps into the detente and locks. When

properly assembled, the dot on the vacuum tube will

align with the dot on the impeller intake.

Removing the Vacuum Bag

1. Unhook the bag.

2. Remove the vacuum bag by pressing both tabs on

the vacuum bag elbow at the same time and pulling

the bag off the blower (Fig. 6).

3. Install the blower tube in order to assemble the unit

as a blower.

4. Make sure the vacuum door is securely latched shut.

Elbow

Tabs

Locking

Clip

Fig. 4

Installing the Vacuum Bag

7. Install the vacuum bag tube over the blower outlet

and push it on until both tabs snap into place (Fig. 6).

Position the bag so its interior elbow slants

downward.

8. Attach the vacuum bag to the vacuum bag hook

located at the underside of the unit.

9. Keep the bag zipped and shut.

Fig. 6

Vacuum

Door Slot

Flat

Area

Tabs

Impeller Intake

Vacuum Tube

Groove

Fig. 5

Vacuum Bag Hook

Never operate the

unit in the blower

configuration without the vacuum door

secured and latched shut.

WARNING:

Fig. 9

3. Snap the clip on to the support fittings on the front

or back of the handle. Clip to the front portion of the

handle when using the unit as a blower, and clip to

the back portion of the handle when using the unit as

a vacuum (Fig. 8).

4. While standing in the operating position, adjust the

length to fit the operator’s size. Pull the tab to

lengthen, pull the strap to shorten (Fig 9).

INSTALLING THE SHOULDER HARNESS (Optional)

The shoulder strap is an optional accessory.

1. Push the strap through the center of the buckle.

2. Pull the strap over the cross bar and down through

the slot in the buckle (Fig. 7).

Fig. 7

Clip

ASSEMBLY INSTRUCTIONS

To avoid serious

personal injury,

never attempt to start the unit when

standing with the unit clipped to the

shoulder strap. Always follow the starting

procedures as described in the Starting/

Stopping Instructions section.

WARNING:

Attach Here for

Blowing

Attach Here for

Vacuuming

Fig. 8

OIL AND FUEL INFORMATION

NOTE: Dispose of the old fuel/oil mix in accordance to

Federal, State and Local regulations.

OIL AND FUEL MIXING INSTRUCTIONS

Old and/or improperly mixed fuel are the main reasons

for the unit not running properly. Be sure to use fresh,

clean unleaded fuel. Follow the instructions carefully for

the proper fuel/oil mixture.

Definition of Blended Fuels

Today's fuels are often a blend of gasoline and

oxygenates such as ethanol, methanol, or MTBE (ether).

Alcohol-blended fuel absorbs water. As little as 1%

water in the fuel can make fuel and oil separate. It forms

acids when stored. When using alcohol-blended fuel,

use fresh fuel (less than 60 days old).

Using Blended Fuels

If you choose to use a blended fuel, or its use is

unavoidable, follow recommended precautions:

• Always use the fresh fuel mix explained in your

operator's manual

• Always agitate the fuel mix before fueling the unit

• Drain the tank and run the engine dry before storing

the unit

Using Fuel Additives

The bottle of 2-cycle oil that came with your unit

contains a fuel additive which will help inhibit corrosion

and minimize the formation of gum deposits. It is

recommended that you use our 2-cycle oil with this unit.

If unavailable, use a good 2-cycle oil designed for

air-cooled engines along with a fuel additive, such as

STA-BIL

Gas Stabilizer or an equivalent. Add 0.8 oz.

(23 ml.) of fuel additive per gallon of fuel according to the

instructions on the container. NEVER add fuel additives

directly to the unit's fuel tank.

Thoroughly mix the proper ratio of 2-cycle engine oil

with unleaded gasoline in a separate fuel can. Use a 40:1

fuel/oil ratio. Do not mix them directly in the engine fuel

tank. See the table below for specific gas and oil mixing

ratios.

NOTE: One gallon (3.8 liters) of unleaded gasoline mixed

with one 3.2 oz. (95 ml.) bottle of

2-cycle oil makes a 40:1 fuel/oil ratio.

UNLEADED GAS 2 CYCLE OIL

1 GALLON US

(3.8 LITERS)

3.2 FL. OZ.

(95 ml)

1 LITER 25 ml

MIXING RATIO - 40:1

Add fuel in a clean,

well ventilated

outdoor area. Wipe up any spilled fuel

immediately. Avoid creating a source of

ignition for spilt fuel. Do not start the engine

until fuel vapors dissipate.

WARNING:

Gasoline is

extremely

flammable. Ignited Vapors may explode.

Always stop the engine and allow it to cool

before filling the fuel tank. Do not smoke

while filling the tank. Keep sparks and open

flames at a distance from the area.

WARNING:

Remove fuel cap

slowly to avoid injury

from fuel spray. Never operate the unit

without the fuel cap securely in place

WARNING:

For proper engine

operation and

maximum reliability, pay strict attention to

the oil and fuel mixing instructions on the

2-cycle oil container. Using improperly mixed

fuel can severely damage the engine.

CAUTION:

STARTING/STOPPING INSTRUCTIONS

On/Off Stop Control

Throttle Control

Idle

Fast

STARTING INSTRUCTIONS

Fig. 10

Fig. 11

STOPPING INSTRUCTIONS

1. Move the throttle control to the idle position ( ). Allow the

engine to cool down by idling.

2. Put the On/Off Stop Control in the OFF (O) position.

NOTE: There is no need to turn the unit on. The On/Off

Stop Control is in the ON (I) position at all times.

2. Fully press and release the primer bulb 10 times,

slowly. Some amount of fuel should be visible in the

primer bulb and fuel lines (Fig. 11). If you can’t see

fuel in the bulb, press and release the bulb as many

times as it takes before you can see fuel in it.

3. Place the unit in the starting position (Fig. 12 as a

blower, Fig. 13 as a vacuum). Move the throttle control

to the idle position () (Fig. 10). This is especially

important during cold starting.

4. Push the blue EZ-Start™ Lever towards the primer

bulb until it clicks and locks into place (Fig. 11).

5. Pull the starter rope out with a controlled and steady

motion until the engine attempts to start. Repeat until

the engine starts.

NOTE: The unit uses Spring Assist Starting™, which

significantly reduces the effort required to start the

engine. You must pull the starter rope out far enough

to hear the engine attempt to start. There is no need

to pull the rope briskly-- there is no harsh resistance

when pulling. Be aware that this starting method is

vastly different from (and much easier than) what you

may be used to.

6. When the engine starts, move the throttle control to the

fast position ( ) and let the engine warm up for 15 to

30 seconds. The blue EZ-Start™ Lever will click off

automatically when you move the throttle control to

the fast position.

...

The engine does not start, go back to step 2.

NOTE: If you are having trouble starting the unit or are

operating in extreme temperatures (below 40º F,

above 90º F), refer to the Troubleshooting section.

Vacuum

Starting

Position

Starter

Rope

Starter

Rope

Blower

Starting

Position

Fig. 12

Fig. 13

Operate this unit only in a

well- ventilated outdoor

area. Carbon monoxide exhaust fumes can be

lethal in a confined area.

WARNING:

Avoid accidental starting.

Make sure you are in the

starting position when pulling the starter rope (Fig.

12 and 13).

To avoid serious injury, the operator and

unit must be in a stable position while starting.

Do not set unit on any surface except a clean, hard

area while starting. Debris such as gravel, sand,

dust and grass could be picked up by the air

intake and thrown out by the discharge opening.

This could damage the unit, property, or cause

serious injury to bystanders or the operator.

WARNING:

To avoid serious

personal injury,

always remove the vacuum bag prior to

refueling the unit. The bag may become a

fire hazard when saturated with fuel.

WARNING:

Primer

Bulb

Blue EZ-Start™

Lever

1. Mix gas with oil. Fill fuel tank with fuel/oil mixture.

See Oil and Fuel Mixing Instructions.

OPERATING INSTRUCTIONS

HOLDING THE BLOWER/VACUUM

Before operating the unit, stand in the operating position.

Check for the following:

• Operator is wearing proper clothing, such as boots,

safety glasses or goggles, ear/hearing protection,

gloves, long pants and long sleeve shirt

• If the conditions are dusty, the operator is wearing a

dust mask or face mask

• The unit is in good working condition

• The tubes and guards are in place and secure

OPERATING TIPS

• Be sure the vacuum bag is zipped closed before

operating the unit.

• Assure the unit is not directed at anybody or any loose

debris before starting the unit.

• Verify that the unit is in good working condition. Make

sure the tubes and guards are in place and secure.

• Always hold the unit securely when operating. Keep a

firm grip on both the front and rear handles.

• To reduce the risk of hearing loss associated with sound

level(s), hearing protection is required.

• Operate power equipment only at reasonable hours—

not early in the morning or late at night when people

might be disturbed. Comply with times listed in local

ordinances. Usual recommendations are 9:00 am to

5:00 pm, Monday through Saturday.

• To reduce noise levels, limit the number of pieces of

equipment used at any one time.

• To reduce noise levels, operate power blowers at the

lowest possible speed to do the job.

• Check your equipment before operation, especially the

muffler, air intakes and air filters.

• Use rakes and brooms to loosen debris before blowing.

• In dusty conditions, slightly dampen surfaces or use a

mister attachment when water is available.

• Conserve water by using power blowers instead of

hoses for many lawn and garden applications,

including areas such as screens, patios, grills, porches,

and gardens.

•Watch out for children, pets, open windows or freshly

washed cars, and blow debris safely away.

• Use the full blower nozzle extension so the air stream

can work close to the ground.

• Clean up after using blowers and other equipment.

Dispose of debris appropriately.

OPERATING AS A BLOWER

1 Use the blower for trees, shrubs, flower beds and

hard-to-clean areas (Fig. 14).

2. Use the unit around buildings and for other normal

cleaning procedures (Fig. 14).

3. Use the blower around walls, overhangs, fences and

screens (Fig. 15).

Fig. 14

Fig. 15

To prevent serious

personal injury or

damage to the unit, make sure blower tubes

or vacuum tubes and the vacuum bag are in

place before you operate the unit.

WARNING:

To avoid serious

personal injury,

wear goggles or safety glasses at all times

when operating this unit. Wear a face mask

or dust mask in dusty locations.

WARNING:

OPERATING INSTRUCTIONS

Fig. 16

OPERATING AS A VACUUM

Check for the following before operating the unit:

• Operator is wearing proper clothing, such as boots,

safety glasses or goggles, ear/hearing protection,

gloves, long pants and long sleeve shirt

• If the conditions are dusty, operator is equipped with a

dust mask or face mask

• The unit is in good working condition-- the vacuum

tubes and vacuum bag are in place and secure.

• The vacuum bag harness is in place and correctly

adjusted

Operation Procedure

Use the unit for vacuuming up light debris like leaves

and paper.

Hold the vacuum, tilting the suction tube slightly (2-4 in

or 50-100 mm above the ground), and use a sweeping

action to collect light debris (Fig. 16). The debris will flow

into the vacuum bag. Items such as small leaves and

small twigs will be mulched as they pass through the fan

housing, allowing the vacuum bag to hold more debris.

When the bag is full, suction will noticeably decrease.

Turn off the unit and allow the impeller to stop before

you unzip the bag. Unzip the bag and empty the

contents before continuing. Refer to Emptying the

Vacuum Bag.

Emptying the Vacuum Bag

1. Remove the bag from the vacuum bag hook.

2. While wearing eye protection and a dust mask, unzip

the vacuum bag and empty the contents into a

garbage bag or container.

3. Turn the bag inside out after initial emptying and

vigorously shake out dust and debris.

4. Zip close and reinstall the vacuum bag.

To avoid serious

personal injury, turn

off the unit and allow the impeller to stop

before opening vacuum door or installing or

removing vacuum bag.

WARNING:

When the upper and

lower vacuum tubes

are removed, make sure the vacuum door is

snapped closed and secured before using

the unit, to avoid injury from the impeller.

WARNING:

Avoid situations that

could catch the

vacuum bag on fire. Do not operate near an

open flame. Do not vacuum warm ash from

fireplaces, barbecue pits, brush piles, etc. Do

not vacuum discarded cigars or cigarettes

unless the cinders are completely cool.

WARNING:

As a vacuum, the

unit is designed to

pick up dry material such as leaves, grass,

small twigs and bits of paper. To avoid serious

personal injury, do not attempt to vacuum wet

debris and/or standing water as this may

result in damage to the blower/ vacuum. To

avoid severe damage to the impeller, do not

vacuum metal, broken glass or similar items.

WARNING:

To avoid serious

personal injury,

never unzip the vacuum bag without

stopping the unit first

WARNING:

To prevent serious

personal injury or

damage to the unit, always install vacuum

tubes, vacuum bag and make sure the

vacuum bag is completely zipped closed

when operating this unit as a vacuum.

WARNING:

MAINTENANCE AND REPAIR INSTRUCTIONS

MAINTENANCE SCHEDULE

Perform these required maintenance procedures at the

frequency stated in the table. These procedures should

also be a part of any seasonal tune-up.

NOTE: Some maintenance procedures may require

special tools or skills. If you are unsure about

these procedures take your unit to any non-road

engine repair establishment, individual or

authorized service dealer. Call 1-800-520-5520

for more information.

NOTE: Maintenance, replacement, or repair of the

emission control devices and system may be

performed by any non-road engine repair

establishment, individual or authorized service

dealer.

In order to assure peak performance of your engine,

inspection of the engine exhaust port may be necessary

after 50 hours of operation. If you notice lost RPM, poor

performance or general lack of acceleration, this service

may be required. If you feel your engine is in need of this

inspection, refer service to any non-road engine repair

establishment, individual or authorized service dealer for

repair. DO NOT attempt to perform this process yourself

as engine damage may result from contaminants

involved in the cleaning process for the port.

FREQUENCY MAINTENANCE REQUIRED REFER TO

Before starting engine Fill fuel tank with fresh fuel Page 11

Every 10 hours Clean and re-oil air filter Page 15

Every 25 hours

Check and clean spark arrestor

Check spark plug condition and gap

Page 16

Page 17

Every 50 hours

Inspect exhaust port and spark arrestor screen for clogging or

obstruction to assure maximum performance levels

Page 16

AIR FILTER MAINTENANCE

Removing the Air Filter/Muffler Cover

1. Remove the four (4) screws securing the air

filter/muffler cover (Fig. 17). Use a flat blade or

T20 Torx bit screwdriver.

2. Pull the cover from the engine. Do not force.

Cleaning the Air Filter

Clean and re-oil the air filter every 10 hours of operation.

It is an important item to maintain. Failure to maintain the

air filter will VOID the warranty.

1. Remove air filter/muffler cover. Refer to Removing

the Air Filter/Muffler Cover.

2. Turn cover over and look inside to locate the air filter.

Remove the air filter from inside the air filter/muffler

cover (Fig. 18).

3. Wash the filter in detergent and water (Fig. 19). Rinse

the filter thoroughly. Squeeze out excess water. Allow

it to dry completely.

Fig. 17

Fig. 18

Fig. 19

Air Filter

Inside Muffler

Cover

To avoid serious

personal injury,

always turn your unit off and allow it to cool

before you clean or service it.

WARNING:

To prevent serious

injury, never perform

maintenance or repairs with unit running.

Always service and repair a cool unit.

Disconnect the spark plug wire to ensure that

the unit cannot start.

WARNING:

Screws

Blue EZ-Start™

Lever

MAINTENANCE AND REPAIR INSTRUCTIONS

Fig. 20

Fig. 21

4. Apply enough clean SAE 30 oil to lightly coat the

filter (Fig. 20).

5. Squeeze the filter to spread and remove excess oil

(Fig. 21).

6. Replace the air filter inside the air filter/muffler cover

(Fig. 18).

NOTE: Operating the unit without the air filter and air

filter/muffler cover assembly will VOID the

warranty.

Reinstalling the Air Filter/Muffler Cover

1. Place the air filter/muffler cover over the back of the

carburetor and muffler. Align the screw holes.

2. Insert the four (4) screws into the holes in the air

filter/muffler cover (Fig. 17) and tighten.

Do not over tighten.

SPARK ARRESTOR MAINTENANCE

1. Remove air filter/muffler cover. Refer to Removing

the Air Filter/Muffler Cover.

2. Locate muffler front and the two (2) bolts securing it to

the engine (Fig. 22). Remove the two (2) bolts using a

T-25 or T-27 Torx bit screwdriver or 5/16-inch socket

or nut driver. Pull muffler off of the engine.

3. Turn muffler over to the back side and locate the

exhaust gasket. Remove the muffler gasket from the

muffler (Fig. 22).

NOTE: If the exhaust gasket is torn or damaged, replace

it with a new gasket before reassembling muffler.

4. Using a small flatblade screwdriver, carefully pry up

the spark arrestor from the recessed hole (Fig. 23).

Remove the spark arrestor from the muffler.

5. Clean the spark arrestor with a wire brush. Replace it

if it is damaged or if it is impossible to clean

thoroughly (Fig. 23).

6. Reinstall the spark arrestor by pressing it into the

recessed hole on the muffler's back side. Make sure

it fits tightly against the muffler and is not raised up.

Fig. 23

Fig. 22

Muffler - Front Side

Muffler - Back Side

Bolts

Exhaust

Gasket

Spark

Arrestor

Muffler - Back Side

Spark

Arrestor

Flatblade

Screwdriver

Spark Arrestor

7. Place the exhaust gasket against muffler's back side.

Align the gasket bolt holes with the bolt holes in the

muffler. While holding exhaust gasket in place, insert

the bolts into the muffler's front side (Fig. 22).

8. Place the muffler (with the exhaust gasket in place

and bolts inserted), against the engine, aligning the

bolt holes. Tighten the bolts to secure the muffler to

the engine.

If using a torque wrench, torque to:

80-90 in.•lb. (9-10.2 N•m)

9. Reinstall the air filter/muffler cover.

If the muffler is not

tightened securely, it

could fall off causing damage to the unit and

possible serious personal injury.

WARNING:

MAINTENANCE AND REPAIR INSTRUCTIONS

Check Fuel Mixture

Old and/or improperly mixed fuel is usually the reason

for improper unit performance. Drain and refill the tank

with fresh, properly-mixed fuel prior to making any

adjustments. Refer to Oil and Fuel Information.

Clean Air Filter

The condition of the air filter is important to the operation

of the unit. A dirty air filter will restrict air flow and

change the air/fuel mixture. This is often mistaken for an

out of adjustment carburetor. Check the condition of the

air filter before adjusting the idle speed screw. Refer to

Air Filter Maintenance.

Adjust Idle Speed Screw

CARBURETOR ADJUSTMENT

The idle speed of the engine is adjustable through the air

filter/muffler cover (Fig. 24).

NOTE: Careless adjustments can seriously damage your

unit. An authorized service dealer should make

carburetor adjustments.

Checking the fuel mixture, cleaning the air filter, and

adjusting the idle speed should solve most engine

problems. If not and all of the following are true:

• the engine will not idle

• the engine hesitates or stalls on acceleration

• there is a loss of engine power

Have the carburetor adjusted by an authorized service

dealer.

Call 1-800-520-5520 for more information.

REPLACING THE SPARK PLUG

Use a Champion RDJ7Y spark plug, or equivalent. The

correct air gap is 0.020 inch (0.5 mm). Remove the plug

after every 25 hours of operation and check its condition.

1. Stop the engine and allow it to cool. Grasp the plug

wire firmly and pull it from the spark plug.

2. Clean around the spark plug. Remove the spark plug

from the cylinder head by turning a 5/8-inch socket

counterclockwise.

3. Replace a cracked, fouled or dirty spark plug. Set

the air gap at 0.020 in. (0.5 mm) using a feeler gauge

(Fig. 25).

4. Install a correctly-gapped spark plug in the cylinder

head. Tighten by turning the 5/8-inch socket

clockwise until snug.

If using a torque wrench torque to:

110-120 in.•lb. (12.3-13.5 N•m)

Do not over tighten.

0.020 in.

(0.5 mm)

Fig. 25

Idle Speed

Screw

Fig. 24

If after checking the fuel mixture and cleaning the air

filter the engine still will not idle, adjust the idle speed

adjuster as follows.

1. Start the engine and let it run at the fast position for a

minute to warm up.

2. Move the throttle control to the idle position and let

the engine idle. If the engine stops, insert a small

phillips or flat blade screwdriver into the hole in the

air filter/muffler cover (Fig. 24). Turn the idle speed

adjuster in, clockwise, 1/8 of a turn at a time (as

needed) until the engine idles smoothly.

3. If the unit appears to be idling too fast, turn the idle

speed adjuster counterclockwise 1/8 of a turn at a

time (as needed), to reduce idle speed.

Do not sand blast,

scrape or clean

electrodes. Grit in the engine could damage

the cylinder.

WARNING:

This unit will need

to be running during

idle speed adjustment. Wear protective

clothing and observe all safety instructions

to prevent serious personal injury.

Also, DO NOT set unit on any surface

except a clean, hard area while starting or

performing any adjustments. Debris such

as gravel, sand, dust, grass, etc. could be

picked up by the air intake and thrown out

by the discharge opening, damaging unit,

property, or causing serious injury to

bystanders or operator.

WARNING:

MAINTENANCE AND REPAIR INSTRUCTIONS

CLEANING THE UNIT

Use a small brush to clean off the outside of the unit.

Do not use strong detergents. Household cleaners that

contain aromatic oils such as pine and lemon, and

solvents such as kerosene, can damage plastic housing

or handle. Wipe off any moisture with a soft cloth.

CLEANING THE VACUUM BAG

1. Empty the bag after each use to avoid deterioration

and obstructing air flow, which will reduce the

performance of the vacuum.

2. Wearing eye protection and a dust mask, clean the

bag as needed. Turn the bag inside out after initial

emptying and vigorously shake out dust and debris.

3. Wash the bag once a year or more often if needed:

a. Remove the vacuum bag.

b. Turn bag inside out.

c. Hang it up.

d. Hose it down thoroughly.

e. Hang to dry.

f. Turn bag right-side out and reinstall.

STORAGE

• Never store a fueled unit where fumes may reach an

open flame or spark.

• Allow the engine to cool before storing.

• Store the unit locked up to prevent unauthorized use

or damage.

• Store the unit in a dry, well-ventilated area.

• Store the unit out of the reach of children.

LONG TERM STORAGE

If you plan on storing the unit for an extended time, use

the following storage procedure:

1. Drain all fuel from the fuel tank into a container with

the same 2-cycle fuel mixture. Do not use fuel that

has been stored for more than 60 days. Dispose of

the old fuel/oil mix in accordance to Federal, State

and Local regulations.

2. Start the engine and allow it to run until it stalls. This

ensures that all fuel has been drained from the

carburetor.

3. Allow the engine to cool. Remove the spark plug and

put 1 oz. (30 ml) of any high quality motor oil or

2-cycle oil into the cylinder. Pull the starter rope

slowly to distribute the oil. Reinstall the spark plug.

NOTE: Remove the spark plug and drain all of the oil

from the cylinder before attempting to start the

unit after storage.

4. Thoroughly clean the unit and inspect it for any loose

or damaged parts. Repair or replace damaged parts

and tighten loose screws, nuts or bolts. The unit is

ready for storage.

TRANSPORTING

• Allow the engine to cool before transporting.

• Drain fuel from unit.

• Tighten fuel cap before transporting.

• Secure the unit while transporting.

ACCESSORIES/ REPLACEMENT PARTS

2-Cycle Oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147543

Spark Plug . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 610311

Fuel Cap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 180000

Vacuum Bag . . . . . . . . . . . . . . . . . . . . . . . . . .753-04458

Shoulder Harness . . . . . . . . . . . . . . . . . . . . . . . . 682075

For specific replacement parts, refer to the parts list

located on the inside back cover of this manual.

To avoid serious

personal injury,

always turn your unit off and allow it to cool

before you clean or service it.

WARNING:

CLEARING A BLOCKED TUBE / IMPELLER

1. Press the On/Off Stop control down in the STOP (O)

position until the engine comes to a complete stop

(Fig. 10).

2. Disconnect the spark plug wire to prevent the unit

from starting.

To avoid serious

personal injury,

always wear gloves to protect yourself from

the impeller blades or other sharp objects.

WARNING:

To avoid serious

personal injury, be

sure the unit is off before cleaning or

performing any maintenance on it.

WARNING:

3. Remove the blower/vacuum tube and the vacuum bag.

4. Carefully remove material blocking the tube or

impeller. Inspect the blades to assure no damage has

occurred. Rotate the impeller blades by hand to

assure the blockage is completely cleared.

5. Reinstall the vacuum bag and blower/vacuum tube.

6. Reconnect the spark plug wire.

TROUBLESHOOTING

CAUSE ACTION

Old or improperly mixed fuel Drain gas tank / Add fresh fuel mixture

Air filter is plugged Replace or clean the air filter

Improper carburetor adjustment Take to an authorized service dealer for

carburetor adjustment

Fouled spark plug Replace or clean the spark plug

Plugged spark arrestor Clean or replace spark arrestor

CAUSE ACTION

Blue EZ-Start lever wasn’t flipped/set Move lever to the starting position

Throttle lever is in the incorrect position Refer to the Starting/Stopping instructions

Empty fuel tank Fill fuel tank with properly mixed fuel

Primer bulb wasn't pressed enough Press primer bulb fully and slowly 10 times

Engine flooded Flip throttle lever to FAST and pull starter rope

Old or improperly mixed fuel Drain gas tank / Add fresh fuel mixture

Fouled spark plug Replace or clean the spark plug

Plugged spark arrestor Clean or replace spark arrestor

The outside temperature is below 40º F Pull the starter rope up to 10-15 times

The outside temperature is above 90º F Squeeze the throttle control and pull the starter rope

ENGINE WILL NOT START

ENGINE WILL NOT IDLE

ENGINE WILL NOT ACCELERATE

ENGINE LACKS POWER OR STALLS

CAUSE ACTION

Air filter is plugged Replace or clean the air filter

Old or improperly mixed fuel Drain gas tank / Add fresh fuel mixture

Improper carburetor adjustment Adjust according to the Carburetor Adjustments section

CAUSE ACTION

Old or improperly mixed fuel Drain gas tank / Add fresh fuel mixture

Improper carburetor adjustment Take to an authorized service dealer for

carburetor adjustment

Dirty air filter Clean or replace the air filter

Plugged spark arrestor Clean or replace spark arrestor

If further assistance is required, contact your authorized service dealer.

Call 1-800-520-5520 for more information.

CAUSE ACTION

Bag full Empty bag, as described in Empty the Vacuum Bag

Blocked tube Clear the blockage as described in Clearing a Blocked

Tube/ Impeller

Blocked impeller Clear the blockage as described in Clearing a Blocked

Tube/ Impeller

Damaged impeller Take the unit to an authorized service dealer

UNIT WILL NOT BLOW OR VACUUM

SPECIFICATIONS

ENGINE*

Engine Type.......................................................................................................................................... Air-Cooled, 2-Cycle

Displacement............................................................................................................................................. 31 cc (1.9 cu. in)

Vacuum Operating RPM................................................................................................................................... 6,800+ rpm

Blower Operating RPM..................................................................................................................................... 7,200+ rpm

Idle Speed RPM ...................................................................................................................................... 3,200 - 4,400 rpm

Ignition Type.......................................................................................................................................................... Electronic

On/Off Stop Control....................................................................................................................................... Rocker Switch

Spark Plug Gap.................................................................................................................................... 0.020 inch (0.5 mm)

Lubrication................................................................................................................................................... Fuel/Oil Mixture

Fuel/Oil Ratio................................................................................................................................................................. 40:1

Carburetor....................................................................................................................................... Diaphragm, All-Position

Starter............................................................................................................................................................... Auto Rewind

Muffler..................................................................................................................................................... Baffled with Guard

Fuel Tank Capacity................................................................................................................................. 13 ounces (384 ml)

BLOWER / VACUUM*

Throttle Control........................................................................................................................................... Finger-Tip Lever

Blower Velocity............................................................................................................................. up to 205 mph (330 kmh)

Blower Air Output ........................................................................................................................ up to 425 cfm (12.1 cmm)

Mulching Ratio...................................................................................................................................................... up to 10:1

Vacuum Bag Capacity................................................................................................................... 1.5 bushels (52.8 Liters)

Shoulder Harness ................................................................................................................................... Single Quick-Snap

Approximate Unit Weight (no fuel, with blower tube) ...................................................................................11.4 lb. (5.2 kg)

*All specifications are based on the latest product information available at the time of printing. We reserve the right to

make changes at any time without notice.

La page charge ...