Lincoln Electric Red-D-Arc GX-271 Mode d'emploi

Marque: Lincoln Electric

Modèle: Red-D-Arc GX-271

Catégorie: Système de soudage

Taper: Mode d'emploi

RED-D-ARC

GX 271Chopper LPG

IM635

October, 2000

Red-D-Arc Spec-Built Welding Equipment

This RED-D-ARC welder is built to RED-D-ARC Extreme Duty

design specifications by Lincoln Electric.

Safety Depends on You

This welder is designed and built with safety in mind.

However, your overall safety can be increased by proper installation

... and thoughtful operation on your part.

DO NOT INSTALL, OPERATE OR REPAIR THIS EQUIPMENT

WITHOUT READING THIS MANUAL AND THE SAFETY

PRECAUTIONS CONTAINED THROUGHOUT.

And, most importantly, think before you act and be careful.

For use with machines having Code Numbers:

10579

North America’s Largest Fleet of Welding Equipment

1-800-245-3660

OPERATOR’S MANUAL

GX 271 Chopper LPG

FOR ENGINE

powered equipment.

1.a. Turn the engine off before troubleshooting and maintenance

work unless the maintenance work requires it to be running.

____________________________________________________

1.b. Operate engines in open, well-ventilated

areas or vent the engine exhaust fumes

outdoors.

____________________________________________________

1.c. Do not add the fuel near an open flame

welding arc or when the engine is running.

Stop the engine and allow it to cool before

refueling to prevent spilled fuel from vaporiz-

ing on contact with hot engine parts and

igniting. Do not spill fuel when filling tank. If

fuel is spilled, wipe it up and do not start

engine until fumes have been eliminated.

____________________________________________________

1.d. Keep all equipment safety guards, covers and devices in

position and in good repair.Keep hands, hair, clothing and

tools away from V-belts, gears, fans and all other moving

parts when starting, operating or repairing equipment.

____________________________________________________

1.e. In some cases it may be necessary to remove safety

guards to perform required maintenance. Remove

guards only when necessary and replace them when the

maintenance requiring their removal is complete.

Always use the greatest care when working near moving

parts.

___________________________________________________

1.f. Do not put your hands near the engine fan.

Do not attempt to override the governor or

idler by pushing on the throttle control rods

while the engine is running.

___________________________________________________

1.g. To prevent accidentally starting gasoline engines while

turning the engine or welding generator during maintenance

work, disconnect the spark plug wires, distributor cap or

magneto wire as appropriate.

SAFETY

ARC WELDING CAN BE HAZARDOUS. PROTECT YOURSELF AND OTHERS FROM POSSIBLE SERIOUS INJURY OR DEATH.

KEEP CHILDREN AWAY. PACEMAKER WEARERS SHOULD CONSULT WITH THEIR DOCTOR BEFORE OPERATING.

Read and understand the following safety highlights. For additional safety information, it is strongly recommended that you

purchase a copy of “Safety in Welding & Cutting - ANSI Standard Z49.1” from the American Welding Society, P.O. Box

351040, Miami, Florida 33135 or CSA Standard W117.2-1974. A Free copy of “Arc Welding Safety” booklet E205 is available

from the Lincoln Electric Company, 22801 St. Clair Avenue, Cleveland, Ohio 44117-1199.

BE SURE THAT ALL INSTALLATION, OPERATION, MAINTENANCE AND REPAIR PROCEDURES ARE

PERFORMED ONLY BY QUALIFIED INDIVIDUALS.

WARNING

Mar ’95

ELECTRIC AND

MAGNETIC FIELDS

may be dangerous

2.a. Electric current flowing through any conductor causes

localized Electric and Magnetic Fields (EMF). Welding

current creates EMF fields around welding cables and

welding machines

2.b. EMF fields may interfere with some pacemakers, and

welders having a pacemaker should consult their physician

before welding.

2.c. Exposure to EMF fields in welding may have other health

effects which are now not known.

2.d. All welders should use the following procedures in order to

minimize exposure to EMF fields from the welding circuit:

2.d.1.

Route the electrode and work cables together - Secure

them with tape when possible.

2.d.2. Never coil the electrode lead around your body.

2.d.3. Do not place your body between the electrode and

work cables. If the electrode cable is on your right

side, the work cable should also be on your right side.

2.d.4. Connect the work cable to the workpiece as close as

possible to the area being welded.

2.d.5. Do not work next to welding power source.

1.h. To avoid scalding, do not remove the

radiator pressure cap when the engine is

hot.

CALIFORNIA PROPOSITION 65 WARNINGS

Diesel engine exhaust and some of its constituents

are known to the State of California to cause can-

cer, birth defects, and other reproductive harm.

The engine exhaust from this product contains

chemicals known to the State of California to cause

cancer, birth defects, or other reproductive harm.

The Above For Diesel Engines

The Above For Gasoline Engines

GX 271 Chopper LPG

SAFETY

ARC RAYS can burn.

4.a. Use a shield with the proper filter and cover

plates to protect your eyes from sparks and

the rays of the arc when welding or observing

open arc welding. Headshield and filter lens

should conform to ANSI Z87. I standards.

4.b. Use suitable clothing made from durable flame-resistant

material to protect your skin and that of your helpers from

the arc rays.

4.c. Protect other nearby personnel with suitable, non-flammable

screening and/or warn them not to watch the arc nor expose

themselves to the arc rays or to hot spatter or metal.

ELECTRIC SHOCK can

kill.

3.a. The electrode and work (or ground) circuits

are electrically “hot” when the welder is on.

Do not touch these “hot” parts with your bare

skin or wet clothing. Wear dry, hole-free

gloves to insulate hands.

3.b. Insulate yourself from work and ground using dry insulation.

Make certain the insulation is large enough to cover your full

area of physical contact with work and ground.

In addition to the normal safety precautions, if welding

must be performed under electrically hazardous

conditions (in damp locations or while wearing wet

clothing; on metal structures such as floors, gratings or

scaffolds; when in cramped positions such as sitting,

kneeling or lying, if there is a high risk of unavoidable or

accidental contact with the workpiece or ground) use

the following equipment:

• Semiautomatic DC Constant Voltage (Wire) Welder.

• DC Manual (Stick) Welder.

• AC Welder with Reduced Voltage Control.

3.c. In semiautomatic or automatic wire welding, the electrode,

electrode reel, welding head, nozzle or semiautomatic

welding gun are also electrically “hot”.

3.d. Always be sure the work cable makes a good electrical

connection with the metal being welded. The connection

should be as close as possible to the area being welded.

3.e. Ground the work or metal to be welded to a good electrical

(earth) ground.

3.f.

Maintain the electrode holder, work clamp, welding cable and

welding machine in good, safe operating condition. Replace

damaged insulation.

3.g. Never dip the electrode in water for cooling.

3.h. Never simultaneously touch electrically “hot” parts of

electrode holders connected to two welders because voltage

between the two can be the total of the open circuit voltage

of both welders.

3.i. When working above floor level, use a safety belt to protect

yourself from a fall should you get a shock.

3.j. Also see Items 6.c. and 8.

FUMES AND GASES

can be dangerous.

5.a. Welding may produce fumes and gases

hazardous to health. Avoid breathing these

fumes and gases.When welding, keep

your head out of the fume. Use enough

ventilation and/or exhaust at the arc to keep

fumes and gases away from the breathing zone. When

welding with electrodes which require special

ventilation such as stainless or hard facing (see

instructions on container or MSDS) or on lead or

cadmium plated steel and other metals or coatings

which produce highly toxic fumes, keep exposure as

low as possible and below Threshold Limit Values (TLV)

using local exhaust or mechanical ventilation. In

confined spaces or in some circumstances, outdoors, a

respirator may be required. Additional precautions are

also required when welding on galvanized steel.

5.b.

Do not weld in locations near chlorinated hydrocarbon

vapors

coming from degreasing, cleaning or spraying operations.

The heat and rays of the arc can react with solvent vapors

form phosgene, a highly toxic gas, and other irritating

products.

5.c. Shielding gases used for arc welding can displace air and

cause injury or death. Always use enough ventilation,

especially in confined areas, to insure breathing air is safe.

5.d. Read and understand the manufacturer’s instructions for this

equipment and the consumables to be used, including the

material safety data sheet (MSDS) and follow your

employer’s safety practices. MSDS forms are available from

your welding distributor or from the manufacturer.

5.e. Also see item 1.b.

Mar ‘95

GX 271 Chopper LPG

FOR ELECTRICALLY

powered equipment.

8.a. Turn off input power using the disconnect

switch at the fuse box before working on

the equipment.

8.b. Install equipment in accordance with the U.S. National

Electrical Code, all local codes and the manufacturer’s

recommendations.

8.c. Ground the equipment in accordance with the U.S. National

Electrical Code and the manufacturer’s recommendations.

CYLINDER may explode

if damaged.

7.a. Use only compressed gas cylinders

containing the correct shielding gas for the

process used and properly operating

regulators designed for the gas and

pressure used. All hoses, fittings, etc. should be suitable for

the application and maintained in good condition.

7.b. Always keep cylinders in an upright position securely

chained to an undercarriage or fixed support.

7.c. Cylinders should be located:

• Away from areas where they may be struck or subjected to

physical damage.

• A safe distance from arc welding or cutting operations and

any other source of heat, sparks, or flame.

7.d. Never allow the electrode, electrode holder or any other

electrically “hot” parts to touch a cylinder.

7.e. Keep your head and face away from the cylinder valve outlet

when opening the cylinder valve.

7.f. Valve protection caps should always be in place and hand

tight except when the cylinder is in use or connected for

use.

7.g. Read and follow the instructions on compressed gas

cylinders, associated equipment, and CGA publication P-l,

“Precautions for Safe Handling of Compressed Gases in

Cylinders,” available from the Compressed Gas Association

1235 Jefferson Davis Highway, Arlington, VA 22202.

iii

SAFETY

iii

Mar ‘95

WELDING SPARKS can

cause fire or explosion.

6.a.

Remove fire hazards from the welding area.

If this is not possible, cover them to prevent

the welding sparks from starting a fire.

Remember that welding sparks and hot

materials from welding can easily go through small cracks

and openings to adjacent areas. Avoid welding near

hydraulic lines. Have a fire extinguisher readily available.

6.b. Where compressed gases are to be used at the job site,

special precautions should be used to prevent hazardous

situations. Refer to “Safety in Welding and Cutting” (ANSI

Standard Z49.1) and the operating information for the

equipment being used.

6.c. When not welding, make certain no part of the electrode

circuit is touching the work or ground. Accidental contact

can cause overheating and create a fire hazard.

6.d. Do not heat, cut or weld tanks, drums or containers until the

proper steps have been taken to insure that such procedures

will not cause flammable or toxic vapors from substances

inside. They can cause an explosion even

though

they have

been “cleaned”. For information, purchase “Recommended

Safe Practices for the

Preparation

for Welding and Cutting of

Containers and Piping That Have Held Hazardous

Substances”, AWS F4.1 from the American Welding Society

(see address above).

6.e. Vent hollow castings or containers before heating, cutting or

welding. They may explode.

6.f.

Sparks and spatter are thrown from the welding arc. Wear oil

free protective garments such as leather gloves, heavy shirt,

cuffless trousers, high shoes and a cap over your hair. Wear

ear plugs when welding out of position or in confined places.

Always wear safety glasses with side shields when in a

welding area.

6.g. Connect the work cable to the work as close to the welding

area as practical. Work cables connected to the building

framework or other locations away from the welding area

increase the possibility of the welding current passing

through lifting chains, crane cables or other alternate cir-

cuits. This can create fire hazards or overheat lifting chains

or cables until they fail.

6.h. Also see item 1.c.

GX 271 Chopper LPG

SAFETY

PRÉCAUTIONS DE SÛRETÉ

Pour votre propre protection lire et observer toutes les instructions

et les précautions de sûreté specifiques qui parraissent dans ce

manuel aussi bien que les précautions de sûreté générales suiv-

antes:

Sûreté Pour Soudage A L’Arc

1. Protegez-vous contre la secousse électrique:

a. Les circuits à l’électrode et à la piéce sont sous tension

quand la machine à souder est en marche. Eviter toujours

tout contact entre les parties sous tension et la peau nue

ou les vétements mouillés. Porter des gants secs et sans

trous pour isoler les mains.

b. Faire trés attention de bien s’isoler de la masse quand on

soude dans des endroits humides, ou sur un plancher

metallique ou des grilles metalliques, principalement dans

les positions assis ou couché pour lesquelles une grande

partie du corps peut être en contact avec la masse.

c. Maintenir le porte-électrode, la pince de masse, le câble

de soudage et la machine à souder en bon et sûr état

defonctionnement.

d.Ne jamais plonger le porte-électrode dans l’eau pour le

refroidir.

e. Ne jamais toucher simultanément les parties sous tension

des porte-électrodes connectés à deux machines à souder

parce que la tension entre les deux pinces peut être le

total de la tension à vide des deux machines.

f. Si on utilise la machine à souder comme une source de

courant pour soudage semi-automatique, ces precautions

pour le porte-électrode s’applicuent aussi au pistolet de

soudage.

2. Dans le cas de travail au dessus du niveau du sol, se protéger

contre les chutes dans le cas ou on recoit un choc. Ne jamais

enrouler le câble-électrode autour de n’importe quelle partie

du corps.

3. Un coup d’arc peut être plus sévère qu’un coup de soliel,

donc:

a. Utiliser un bon masque avec un verre filtrant approprié

ainsi qu’un verre blanc afin de se protéger les yeux du ray-

onnement de l’arc et des projections quand on soude ou

quand on regarde l’arc.

b. Porter des vêtements convenables afin de protéger la

peau de soudeur et des aides contre le rayonnement de

l‘arc.

c. Protéger l’autre personnel travaillant à proximité au

soudage à l’aide d’écrans appropriés et non-inflammables.

4. Des gouttes de laitier en fusion sont émises de l’arc de

soudage. Se protéger avec des vêtements de protection libres

de l’huile, tels que les gants en cuir, chemise épaisse, pan-

talons sans revers, et chaussures montantes.

5. Toujours porter des lunettes de sécurité dans la zone de

soudage. Utiliser des lunettes avec écrans lateraux dans les

zones où l’on pique le laitier.

6. Eloigner les matériaux inflammables ou les recouvrir afin de

prévenir tout risque d’incendie dû aux étincelles.

7. Quand on ne soude pas, poser la pince à une endroit isolé de

la masse. Un court-circuit accidental peut provoquer un

échauffement et un risque d’incendie.

8. S’assurer que la masse est connectée le plus prés possible

de la zone de travail qu’il est pratique de le faire. Si on place

la masse sur la charpente de la construction ou d’autres

endroits éloignés de la zone de travail, on augmente le risque

de voir passer le courant de soudage par les chaines de lev-

age, câbles de grue, ou autres circuits. Cela peut provoquer

des risques d’incendie ou d’echauffement des chaines et des

câbles jusqu’à ce qu’ils se rompent.

9. Assurer une ventilation suffisante dans la zone de soudage.

Ceci est particuliérement important pour le soudage de tôles

galvanisées plombées, ou cadmiées ou tout autre métal qui

produit des fumeés toxiques.

10. Ne pas souder en présence de vapeurs de chlore provenant

d’opérations de dégraissage, nettoyage ou pistolage. La

chaleur ou les rayons de l’arc peuvent réagir avec les vapeurs

du solvant pour produire du phosgéne (gas fortement toxique)

ou autres produits irritants.

11. Pour obtenir de plus amples renseignements sur la sûreté,

voir le code “Code for safety in welding and cutting” CSA

Standard W 117.2-1974.

PRÉCAUTIONS DE SÛRETÉ POUR

LES MACHINES À SOUDER À

TRANSFORMATEUR ET À

REDRESSEUR

1. Relier à la terre le chassis du poste conformement au code de

l’électricité et aux recommendations du fabricant. Le dispositif

de montage ou la piece à souder doit être branché à une

bonne mise à la terre.

2. Autant que possible, I’installation et l’entretien du poste seront

effectués par un électricien qualifié.

3. Avant de faires des travaux à l’interieur de poste, la debranch-

er à l’interrupteur à la boite de fusibles.

4. Garder tous les couvercles et dispositifs de sûreté à leur

place.

Mar. ‘93

GX 271 Chopper LPG

Thank You

for selecting this QUALITY product. We want you to take pride in

operating this product ••• as much pride as we have in bringing

this product to you!

Read this Operators Manual completely before attempting to use this equipment. Save this manual and keep it

handy for quick reference. Pay particular attention to the safety instructions we have provided for your protection.

The level of seriousness to be applied to each is explained below:

WARNING

This statement appears where the information must be followed exactly to avoid serious personal injury or

loss of life.

This statement appears where the information must be followed to avoid minor personal injury or damage to

this equipment.

CAUTION

Please Examine Carton and Equipment For Damage Immediately

When this equipment is shipped, title passes to the purchaser upon receipt by the carrier. Consequently, Claims

for material damaged in shipment must be made by the purchaser against the transportation company at the

time the shipment is received.

Please record your equipment identification information below for future reference. This information can be

found on your machine nameplate.

Model Name & Number _____________________________________

Code & Serial Number _____________________________________

Date of Purchase _____________________________________

Whenever you request replacement parts for or information on this equipment always supply the information

you have recorded above.

GX 271 Chopper LPG

TABLE OF CONTENTS

Page

Installation.......................................................................................................................Section A

Technical Specifications.......................................................................................................A-1

Installation Instructions.........................................................................................................A-3

Location and Ventilation................................................................................................A-3

Storing...........................................................................................................................A-3

Stacking ........................................................................................................................A-3

Angle of Operation ........................................................................................................A-3

Lifting.............................................................................................................................A-3

Additional Safety Precautions .......................................................................................A-3

Pre-Operation Engine Service..............................................................................................A-4

Fuel ...............................................................................................................................A-4

Oil..................................................................................................................................A-4

Battery Connections .............................................................................................................A-5

Muffler ...........................................................................................................................A-5

Spark Arrester ...............................................................................................................A-5

Electrical Connections..........................................................................................................A-6

Machine Grounding.......................................................................................................A-6

Welding Cable Connections..........................................................................................A-6

Auxiliary Power Receptacles, Plugs, and Hand-Held Equipment ........................................A-7

Circuit Breakers....................................................................................................................A-7

Premises Wiring ...................................................................................................................A-7

Operation.........................................................................................................................Section B

General Description..............................................................................................................B-1

Design Features ...................................................................................................................B-1

Other Features .....................................................................................................................B-2

Recommended Applications.................................................................................................B-2

Limitations ............................................................................................................................B-2

Additional Safety Precautions .............................................................................................B-2

Controls and Settings ..................................................................................................................B-3

Welder / Generator Controls .........................................................................................B-3

Engine Operation .................................................................................................................B-4

Before Starting the Engine ............................................................................................B-4

Starting the Engine........................................................................................................B-4

Stoping the Engine........................................................................................................B-5

Fuel Consumption Data ................................................................................................B-5

Welding Operation................................................................................................................B-6

Welder Controls - Function and Operation....................................................................B-6

Stick Welding ................................................................................................................B-7

Pipe Welding .................................................................................................................B-7

TIG Welding ..................................................................................................................B-7

Wire Welding.................................................................................................................B-8

Summary of Welding Processes and Machine Settings ...............................................B-9

Auxiliary Power...................................................................................................................B-10

Simultaneous Welding and Power Loads ...................................................................B-10

Accessories.....................................................................................................Section C

General Options / Accessories..............................................................................C-1

TIG Welding Options / Accessories.......................................................................C-1

Semiautomatic FCAW and MIG Welding Options / Accessories.........................................

C-2

Connection Diagrams for Accessories ..................................................................C-3

GX 271 Chopper LPG

vii

TABLE OF CONTENTS

Page

Maintenance ....................................................................................................Section D

Safety Precautions ................................................................................................D-1

Routine and Periodic Engine Maintenance ...........................................................D-1

Engine Maintenance Parts..............................................................................D-1

Engine Maintenance Schedule .......................................................................D-2

Changing the Engine Oil .................................................................................D-3

Changing the Engine Oil Filter ........................................................................D-3

Air Cleaner Service .........................................................................................D-3

Spark Plug Service .........................................................................................D-4

Fuel Filter Service ...........................................................................................D-5

Engine Adjustments ........................................................................................D-5

Battery Maintenance .......................................................................................D-5

Servicing Optional Spark Arrestor .........................................................................D-6

Welder / Generator Maintenance ..........................................................................D-6

Storage ...........................................................................................................D-6

Cleaning..........................................................................................................D-6

Brush Removal and Replacement ..................................................................D-6

Troubleshooting..............................................................................................Section E

Safety Precautions.................................................................................................E-1

How to Use Troubleshooting Guide.......................................................................E-1

Troubleshooting Guide ..........................................................................................E-2

Wiring Diagram & Dimension Print................................................................Section F

Parts List ......................................................................................................P325 Series

A-1

INSTALLATION

GX 271 Chopper LPG

A-1

TECHNICAL SPECIFICATIONS - Red-D-Arc GX-271 LPG (K1680-1)

Make/Model Description Speed (RPM) Displacement Starting Capacities

System

Kohler 2 cylinder High Idle 3700 38.1 cu. in

12VDC battery

Fuel: LPG cyl.

CH20S 20.0 HP @ Low Idle 2400 (624 cc) (Group 58, 435

Command® w/LP 3600 RPM Full Load 3500 cold crank amps)

Full Load Bore x Stroke Oil: 2.0 Qts.

4 Cycle 25A. Alternator 1.9 L

Air Cooled 3.03” x 2.64”

LPG Engine

(77 mm x 67 mm)

Overhead Valves

INPUT - ENGINE

RATED OUTPUT - WELDER

HEIGHT WIDTH DEPTH WEIGHT

30.3 in. 19.1 in. 43.8 in. 469 lbs.

770 mm 485 mm 1113 mm 212 kg.

OUTPUT - GENERATOR

Welding Output Volts at Rated Amps Duty Cycle

Max. OCV @ 3700 RPM

CC Stick/TIG, Pipe and CV Wire Welding

275 Amps 28 volts 100%

80 volts DC

300 Amps 25 volts 60%

Auxiliary Power

8,000 Watts, 60 Hz

120/240 Volts

100 % Duty Cycle

42 Volt Auxiliary Power for Wire Feeders

PHYSICAL DIMENSIONS

1. Duty cycle is based on a 10 minute period. This machine can be loaded to 300 amps for 6 minutes out of every 10 minute

period.

2. Output rating in watts is equivalent to volt-amperes at unity power factor. Output voltage is within ± 10% at all loads up to

rated capacity. When welding, available auxiliary power will be reduced.

A-2

INSTALLATION

GX 271 Chopper LPG

A-2

TECHNICAL SPECIFICATIONS - Red-D-Arc GX-271 (K1680-1)

A-3

INSTALLATION

GX 271 Chopper LPG

A-3

INSTALLATION INSTRUCTIONS

SAFETY PRECAUTIONS

Only qualified personnel should install,

use, or service this equipment.

LOCATION AND VENTILATION

Whenever you use the GX-271, be sure that clean

cooling air can flow through the machine’s engine and

the machine case. Avoid dusty, dirty areas. Also,

keep the machine away from heat sources. Do not

place the engine end of the machine anywhere near

hot engine exhaust from another machine or closer

than two feet from a wall. And of course, make sure

that engine exhaust is ventilated to an open, outside

area.

The GX-271 may be used outdoors. Do not set the

machine in puddles or otherwise submerge it in water.

Such practices pose safety hazards and cause

improper operation and corrosion of parts.

Always operate the GX-271 with the case roof on and

all machine components completely assembled. This

will protect you from the dangers of moving parts, hot

metal surfaces, and live electrical devices.

Do not attempt to use this equipment until you

have thoroughly read the engine manufacturer’s

manual supplied with your welder. It includes

important safety precautions, detailed engine

starting, operating and maintenance instructions,

and parts lists.

------------------------------------------------------------------------

ELECTRIC SHOCK can kill.

• Do not touch electrically live parts or

electrode with skin or wet clothing.

• Insulate yourself from work and

ground

• Always wear dry insulating gloves.

------------------------------------------------------------------------

ENGINE EXHAUST can kill.

• Use in open, well ventilated areas or

vent exhaust outside.

------------------------------------------------------------------------

MOVING PARTS can injure.

• Do not operate with doors open or

guards off.

• Stop engine before servicing.

• Keep away from moving parts.

------------------------------------------------------------------------

See additional warning information at

front of this operator’s manual.

-----------------------------------------------------------

WARNING

STORING

1. Store the machine in a cool, dry place when it is

not in use. Protect it from dust and dirt. Keep it

where it can’t be accidentally damaged from con-

struction activities, moving vehicles, and other

hazards.

2. Drain the engine oil and refill with fresh oil. Run

the engine for about five minutes to circulate oil to

all the parts. See the MAINTENANCE section of

this manual for details on changing oil.

3. Remove the battery, recharge it, and adjust the

electrolyte level. Store the battery in a dry, dark

place.

STACKING

GX-271 machines CANNOT be stacked.

ANGLE OF OPERATION

Place the machine on a secure, level surface whenev-

er you use it or store it. Any surfaces you place it on

other than the ground must be firm, non-skid, and

structurally sound.

The engine is designed to run in a level position for

best performance. It can operate at an angle, but this

should never be more than 15 degrees in any direc-

tion. If you do operate it at a slight angle, be sure to

check the oil regularly and keep the oil level at the

FULL mark as it would be in its normal level condition.

LIFTING

The GX-271 weighs approximately 469 lbs/212 kg. A

lift bail is mounted to the machine frame and should

always be used when lifting the machine.

ADDITIONAL SAFETY PRECAUTIONS

FALLING EQUIPMENT can cause

injury.

● Do not lift this machine using lift

bale if it is equipped with a heavy

accessory such as trailer or gas

cylinder.

● Lift only with equipment of adequate lifting

capacity.

● Be sure machine is stable when lifting.

WARNING

A-4

INSTALLATION

GX 271 Chopper LPG

A-4

If growing bubbles appear, there is a leak. Re-tighten

connection or replace defective component. Retest to

make sure that there is no leak.

Leak test must be performed each time the fuel cylin-

der is replaced.

Always close the cylinder valve when the machine is

not being used.

The specification for aluminum lift truck cylinders are

shown below:

Capacity Cylinder Weight Footring

LP-Gas Volume Empty Outside

(LBS.) (Cu. In.) (LBS.) Diameter

33.5 2219 22.5 9 3/8”

43.5 2873 25.5 9 3/8”

Note: The GX 271 LPG cannot

be used with vapor draw

LP gas cylinders such as those used for recreation

vehicles, trailers, grilles, and boats.

OIL

The GX 271 is shipped with the engine crankcase filled

with SAE 10W-30 oil. Check the oil level before starting

the engine. If it is not up to the full mark on the dip stick,

add oil as required. Make certain that the oil filler cap is

tightened securely. Refer to the engine Owner’s Manual

for specific oil recommendations.

PRE-OPERATION ENGINE SERVICE

READ the engine operating and maintenance instruc-

tions supplied with this machine.

FUEL

A lift truck type coupler is provided on the supplied

fuel line for easy hand attachment to a lift truck type

LPG fuel cylinder. The fuel cylinder must meet D.O.T.

Specification 4E-240. The valve on the fuel cylinder

must

be installed on the outlet marked “LIQUID”.

The engine will not develop full power if connected to

the vapor outlet.

Be certain that the cylinder valve is CLOSED before

attempting to attach the fuel supply hose coupler to the

cylinder. Connect the coupler to the fuel cylinder and

tighten by hand.

___________________________________________

After connecting the fuel supply to the supply cylinder,

open the valve on the fuel cylinder and leak test by

brushing a 50/50 soap and water solution on to the fol-

lowing connections:

• Both ends of the fuel hose where it enters the metal connector.

• The threaded fitting on the end of fuel hose attached to the GX

271 LPG fuel shut off solenoid.

• The fuel hose coupler and the connection to the cylinder valve.

• The stem of the cylinder valve and where the valve is attached

to the top of the cylinder.

• All other fittings on top of the fuel cylinder.

CAUTION

LPG

fuel can cause fire or explosion.

• All leak testing must be done in a well

ventilated area free from all potential

ignition sources.

• Keep sparks and flame away from machine and

LPG supply cylinder.

• Do not expose the LPG supply cylinder to temper-

atures exceeding 120°F (49°C).

• Do not weld on or near the LPG supply cylinder.

• Do not smoke or allow any potential ignition sources

near the LPG supply cylinder.

•

Always be certain that the LPG supply cylinder is NOT

in the welding circuit. Do not allow either welding

cable to come in contact with the supply cylinder.

• Replace the fuel supply hose if there is excessive

abrasion, cracks or wear or if the hose is cut.

------------------------------------------------------------------------

WARNING

CAUTION

LUBRICATION SYSTEM CAPACITY

(INCLUDING FILTER)

Kohler CH20S - 2.0 Quarts (1.9 Liters)

A-5

INSTALLATION

GX 271 Chopper LPG

A-5

BATTERY CONNECTIONS

GASES FROM BATTERY can explode.

● Keep sparks, flame and cigarettes

away from battery.

To prevent EXPLOSION when:

● INSTALLING A NEW BATTERY — disconnect

negative cable from old battery first and connect

to new battery last.

● CONNECTING A BATTERY CHARGER —

remove battery from welder by disconnecting nega-

tive cable first, then positive cable and battery

clamp. When reinstalling, connect

negative cable last. Keep well ventilated.

● USING A BOOSTER — connect positive lead to

battery first then connect negative lead to negative

battery lead at engine foot.

BATTERY ACID can burn eyes and

skin.

● Wear gloves and eye protection and

be careful when working near battery.

● Follow instructions printed on battery.

------------------------------------------------------------------------

WARNING

IMPORTANT: To prevent ELECTRICAL DAMAGE

WHEN:

a) Installing new batteries.

b) Using a booster.

Use correct polarity — Negative Ground.

The GX 271 is shipped with the negative battery cable

disconnected. Before you operate the machine, make

sure the Engine Switch is in the STOP position and

attach the disconnected cable securely to the negative

(-) battery terminal.

Remove the insulating cap from the negative battery

terminal. Replace and tighten negative battery cable

terminal. NOTE: This machine is furnished with a wet

charged battery; if unused for several months, the bat-

tery may require a booster charge. Be sure to use the

correct polarity when charging the battery.

MUFFLER

Shut off the machine and allow the muffler to cool

before touching the muffler.

------------------------------------------------------------------------

SPARK ARRESTER

Engine mufflers may emit sparks when the engine is

running. Some federal, state, or local laws require

spark arresters in locations where unarrested sparks

could present a fire hazard.

Standard mufflers do not act as spark arresters.

When local laws require it, a spark arrester must be

installed on the machine and properly maintained.

An incorrect spark arrester may lead to damage to the

engine or reduce performance.

------------------------------------------------------------------------

CAUTION

A-6

INSTALLATION

GX 271 Chopper LPG

A-6

ELECTRICAL CONNECTIONS

See Figure B.1 in the OPERATION section of this

manual for location of the 120 and 240 volt recepta-

cles, weld output terminals, circuit breakers and

ground stud.

MACHINE GROUNDING

Because the GX 271 creates its own power from its

engine driven generator, and if the machine is not

connected to premises wiring (home, shop, etc.), you

do not need to connect the machine frame to an earth

ground. However, for best protection against electri-

cal shock, connect a heavy gauge wire (#8 AWG or

larger) from the ground stud located on the bottom of

the output panel (See Figure B.1) to a suitable earth

ground such as a metal pipe driven into the ground.

Do not ground the machine to a pipe that carries

explosive or combustible material.

------------------------------------------------------------------------

When the GX 271 is mounted on a truck or a trailer,

the machine generator ground stud MUST be securely

connected to the metal frame of the vehicle. See

Figure B.1. The ground stud is marked with the

ground symbol.

If the GX 271 is connected to premises wiring such as

a home or shop, it must be properly connected to the

system earth ground.

WELDING CABLE CONNECTIONS

CABLE SIZE AND LENGTH

Be sure to use welding cables that are large enough.

The correct size and length becomes especially

important when you are welding at a distance from the

welder.

Table A.1 lists recommended cable sizes and lengths

for rated current and duty cycle. Length refers to the

distance from the welder to the work and back to the

welder. Cable diameters are increased for long cable

lengths to reduce voltage drops.

Lincoln Electric offers a welding accessory kit with the

properly specified welding cables. See the

ACCESSORIES section of this manual for more infor-

mation.

WARNING

Table A.1

CABLE INSTALLATION

Install the welding cables to your GX 271 as follows.

See Figure B.1 for location of parts.

1. The engine must be OFF to install welding cables.

2. Remove the flanged nuts from the output terminals.

3. Connect the electrode holder and work cables to

the weld “+” and “-” output terminals. The terminals

are identified on the case front. The polarity require-

ment for the welding process being used deter-

mines which terminal the electrode cable is

attached to.

4. Tighten the flanged nuts securely.

5. Be certain that the metal piece you are welding (the

“work”) is properly connected to the work clamp and

cable.

6. Check and tighten the connections periodically.

• Loose connections will cause the output terminals to

overheat. The terminals may eventually melt.

• Do not cross the welding cables at the output termi-

nal connection. Keep the cables isolated and sepa-

rate from one another.

------------------------------------------------------------------------

TOTAL COMBINED LENGTH OF

ELECTRODE AND WORK CABLES

Cable Length

0-50 Ft. (0-15 meters)

50-100 Ft. (15-39 meters)

100-150 Ft. (30-46 meters)

150-200 Ft. (46-61 meters)

200-250 Ft. (61-76 meters)

Cable Size for

300 Amps

100% Duty Cycle

1/0 AWG

2/0 AWG

3/0 AWG

CAUTION

A-7

INSTALLATION

GX 271 Chopper LPG

A-7

AUXILIARY POWER RECEPTACLES,

PLUGS, AND HAND-HELD EQUIPMENT

The control panel of the GX 271 features three auxil-

iary power receptacles: See Figure B.1.

• Two 15 amp, 120 volt duplex (double outlet) recepta-

cles.

• One 50 amp 120/240 volt single outlet receptacle.

Through these receptacles the machine can supply up

to 8,000 rated continuous watts of single-phase, 60

Hz AC power.

For further protection against electric shock, any elec-

trical equipment connected to the 120V duplex recep-

tacles must use a three-blade, grounded type plug or

an Underwriter’s Laboratories (UL) approved double

insulation system with a two-blade plug. Lincoln

offers an accessory plug kit that has the right type of

plugs. See the ACCESSORIES section of this manual

for more information.

If you need ground fault protection for hand-held

equipment refer to the K896-1 GFCI Receptacle kit in

the ACCESSORIES section of this manual for more

information.

For recommended extension cord lengths and sizes

see Table A.1.

CIRCUIT BREAKERS

The GX 271 machines are equipped with 50 amp cir-

cuit breakers on the 120/240 V receptacle and 15 amp

circuit breakers on the 120 receptacles for overload

protection. Under high heat a breaker may tend to trip

at lower loads than it would normally.

Never bypass the circuit breakers. Without overload

protection, the GX 271 could overheat and/or cause

damage to the equipment being used.

------------------------------------------------------------------------

CAUTION

PREMISES WIRING

The GX 271 is suitable for temporary, standby, or

emergency power using the engine manufacturer’s

recommended maintenance schedule. With its three-

wire grounded neutral generator, it can be permanent-

ly installed as a standby power unit for 240 volt, three

wire, single phase 33 ampere service.

Only a licensed, certified, trained electrician should

install the machine to a premises or residential elec-

trical system. Be certain that:

• The installation complies with the National Electrical

Code and all other applicable electrical codes.

• The premises is isolated and no feedbacking into

the utility system can occur. Certain state and local

laws require the premises to be isolated before the

generator is linked to the premises. Check your

state and local requirements.

• A double pole, double throw transfer switch in con-

junction with the properly rated double throw circuit

breaker is connected between the generator power

and the utility meter.

------------------------------------------------------------------------

The following information and the connection diagram,

Figure A.1, can be used as a guide by the electrician

for most applications to premises wiring.

1. Install a double pole, double throw switch between

the power company meter and the premises dis-

connect. The switch rating must be the same as

or greater than the premises disconnect and

service overcurrent protection.

2. Take the necessary steps to assure that the load is

limited to the capacity of the GX 271 by installing a

35 amp 240 volt double pole circuit breaker.

Maximum rated load for the 240 volt auxiliary is 33

amperes. Loading above 33 amperes will reduce

output voltage below the allowable -10% of rated

voltage. This may damage appliances or other

motor-driven equipment.

3. Install a 50 amp 120/240 volt plug (NEMA type 14-

50) to a double pole circuit breaker using No. 8 or

larger, 4 conductor cable of the desired length.

(The 50 amp 120/240 volt plug is available in the

optional power plug kit.

4. Plug this cable in to the 50 amp 120/240 volt recep-

tacle on the GX 271 case front.

WARNING

A-8

INSTALLATION

GX 271 Chopper LPG

A-8

Connection of GX 271 to premises wiring must be done by a licensed electrician and must comply with

the National Electrical Code and all other applicable electrical codes.

230 Volt

60 Hz.

3-Wire

Service

POWER

COMPANY

METER

230 VOLT

115 VOLT

LOAD

NEUTRAL

BUS

GROUND

PREMISES

DISCONNECT AND

SERVICE

OVERCURRENT

PROTECTION

GND

NOTE: No. 8 COPPER CONDUCTOR CABLE SEE

NATIONAL ELECTRICAL CODE FOR ALTERNATE WIRE

SIZE RECOMMENDATIONS.

230 VOLT

GROUNDED CONDUCTOR

35 AMP

230 VOLT

DOUBLE

POLE

CIRCUIT

BREAKER

DOUBLE POLE DOUBLE THROW

SWITCH RATING TO BE THE SAME

AS OR GREATER THAN PREMISES

SERVICE OVERCURRENT

PROTECTION.

50 AMP, 115/230

VOLT PLUG

NEMA TYPE 14-50

50 AMP, 115/230 VOLT

RECEPTACLE

Figure A.1

CONNECTION OF GX 271 TO PREMISES WIRING

Table A.1

Extension Cord Length Recommendations

WARNING

Current Voltage Load Maximum Allowable Cord Length in ft (m) for Conductor Size (AWG)

(Amps) (Volts) (Watts) 14 AWG 12 AWG 10 AWG 8 AWG 6 AWG 4 AWG

15 120 1800 30 (9) 40 (12) 75 (23) 125 (38) 175 (53) 300 (91)

15 240 3600 60 (18) 75 (23) 150 (46) 225 (69) 350 (107) 600 (183)

20 240 4800 60 (18) 100 (30) 175 (53) 275 (84) 450 (137)

25 240 600 90 (27) 150 (46) 225 (69) 250 (76)

30 240 7200 75 (23) 120 (37) 175 (53) 300 (91)

35 240 8400 100 (30) 150 (46) 250 (76)

B-1

OPERATION

GX 271 Chopper LPG

B-1

OPERATING INSTRUCTIONS

Read and understand this entire section before oper-

ating your GX 271.

SAFETY INSTRUCTIONS

Do not attempt to use this equipment until you have

thoroughly read all operating and maintenance man-

uals supplied with your machine. They include impor-

tant safety precautions, detailed engine starting,

operating and maintenance instructions and parts

lists.

ELECTRIC SHOCK can kill.

•Do not touch electrically live parts such

as output terminals or internal wiring.

•Insulate yourself from the work and

ground.

•Always wear dry insulating gloves.

------------------------------------------------------------------------

ENGINE EXHAUST can kill.

•Use in open, well ventilated areas or

vent exhaust outside

•Do not stack anything near the engine.

------------------------------------------------------------------------

MOVING PARTS can injure.

•Do not operate with doors open or

guards off.

•Stop engine before servicing.

•Keep away from moving parts

------------------------------------------------------------------------

Only qualified personnel should operate this equip-

ment.

GENERAL DESCRIPTION

The GX 271 is an engine driven, multi-process DC arc

welder and AC power generator for commercial and

residential applications. As a generator it can supply

up to 8,000 continuous watts of 120/240 volt, 60 Hz,

single-phase AC power to operate AC power tools,

battery chargers, and lighting; it can also be used to

provide standby power. As a welder it provides up to

300 amps of DC current for DC stick welding and DC

semiautomatic wire feed welding. The GX 271 can

also perform DC TIG welding.

DESIGN FEATURES

FOR WELDING:

• DC constant current output for stick and TIG weld-

ing - Two continuous CC output settings of 20 to

300 amps, one for general purpose stick and tig

welding and one with a fixed controlled slope for out

of position and pipe welding. The STICK-TIG mode

includes an arc force control.

• DC constant voltage output for MIG and Flux Cored

wire welding - One continuous CV welding range of

11 to 32 volts. Excellent MIG welding with CO2 and

blended gas. A pinch control allows the arc to be

fine tuned from “soft “ to “crisp”. The recommended

wire feeder is the K446 LN-25 with the K624-1 42

Volt Remote Output Control Module or the K449 LN-

25 with an internal contactor.

• 100% duty cycle at 275 amps output.

• Remote control capability. Nine pin and fourteen

pin connectors for easy connection of Lincoln wire

feeders and remote control accessories. The 14 pin

connector includes power for 42 VAC wire feeders.

• Internal “Solid State” contactor allows for the selec-

tion of “hot” or “cold” output terminals.

FOR AUXILIARY POWER

• 8,000 watts of 240 V AC, 60Hz auxiliary power.

• Power for tools, 120/240 lights, electric pumps and

for standby emergency power.

• Power a 1-1/2 HP motor (provided it is started under

no load).

• Two 15 amp industrial grade 120 V AC duplex

receptacles for up to 60 amps of 120 VAC power.

WARNING

GX 271 Chopper LPG

B-2

OPERATION

B-2

• One 50 amp 120/240 V AC, single phase power,

dual voltage receptacle with two 50 amp circuit

breakers. Supplies up to 33 amps of 240 V AC and

up to 66 amps of 120 V AC single phase auxiliary

power per side to separate branch circuits (not in

parallel). Allows easy connection to premises wiring.

• Welding and AC auxiliary power at the same time

(within machine total capacity).

OTHER FEATURES

• Overhead valve, 20 HP LPG engine. Designed for

long life, easy maintenance and excellent fuel econ-

omy.

• Engine protection system shuts the engine down

with low oil pressure.

• Large maintenance-free battery. Group 58 with 435

cold cranking amps.

• Battery charging ammeter.

• Engine hour meter.

• Automatic idler reduces engine speed when not

welding or drawing auxiliary power. This feature

reduces fuel consumption and extends engine life.

• Compact size fits crosswise in compact size pick-up

truck.

• Copper alternator windings for dependability and

long life.

• CSA approved.

RECOMMENDED APPLICATIONS

WELDER

The GX 271 provides excellent constant current DC

welding output for stick (SMAW) welding and for TIG

welding, and it offers constant voltage output for DC

semiautomatic wire feed welding.

GENERATOR

The GX 271 gives AC power output for medium use

demands.

LIMITATIONS

• The GX 271 is not recommended for any process-

es besides those that are normally performed using

stick welding (SMAW), TIG welding (GTAW), MIG

(GMAW) welding and Innershield® (FCAW) welding.

• The GX 271 is not recommended

for pipe thawing.

• During welding, generator power is limited and out-

put voltages can drop. Therefore, DO NOT OPER

ATE ANY SENSITIVE ELECTRICAL EQUIPMENT

WHILE YOU ARE WELDING. See Table B.4 for

permissible simultaneous welding and auxiliary

power loads.

ADDITIONAL SAFETY PRECAUTIONS

Always operate the welder with the roof and case

sides in place as this provides maximum protection

from moving parts and assures proper cooling air flow.

Read and understand all Safety Precautions before

operating this machine. Always follow these and any

other safety procedures included in this manual and in

the Engine Owner’s Manual.

Only qualified personnel should install, use, or service

this equipment.

GX 271 Chopper LPG

B-3

OPERATION

B-3

CONTROLS AND SETTINGS

All generator/welder controls are located on the

Output Control Panel of the machine case front. Idler

control, and start/stop controls are also on the case

front. See Figure B.1 and the explanations that follow.

FIGURE B.1

OUTPUT PANEL CONTROLS

WELDER/GENERATOR CONTROLS

See Figure B.1 for the location of the following features:

1. OUTPUT CONTROL: Allows full range adjustment of

welding current or voltage.

2. ARC CONTROL: The “ARC CONTROL” potentiome-

ter is active in two modes: “STICK/TIG” and “WIRE

WELDING” with different purposes in each mode.

3. MODE SWITCH: Selects three possible modes of

welding operation, 1.) CC Stick/Tig welding, 2.) Pipe

welding, and 3.) CV Wire Welding.

4. LOCAL/REMOTE CONTROL SWITCH: Allows the

operator to control welding output at the welding con-

trol panel or at a wire feeder, TIG amptrol, or a K857

remote control.

5. WELDING TERMINALS SWITCH: The toggle switch

labeled “WELDING TERMINALS ALWAYS ON” and

“WELDING TERMINALS REMOTELY CON-

TROLLED” is used to control the operation of the

solid state output contactor. With the switch in the

“WELDING TERMINALS ALWAYS ON” position, the

contactor is closed at low and high idle.

6. BATTERY CHARGER CIRCUIT BREAKER: Opens

the engine battery circuit if a short develops. Engine

will not crank if this circuit breaker is open.

7. WIRE FEEDER POWER CIRCUIT BREAKER: Opens

the wire feeder circuit and disables the feeder if a fault

is detected in the circuit.

8. 15 AMP, 120 VOLT DUPLEX RECEPTACLES:

Connection point for supplying 120 volt power to oper-

ate one or more electrical devices.

9. 50 AMP, 120/240 VOLT RECEPTACLE: Connection

point for supplying 240 volt power to operate one

electrical device.

10. WELD OUTPUT TERMINALS WITH FLANGE NUT:

Provides the connection point for the electrode and

work cables.

11. GROUND STUD: Provides a connection point for

connecting the machine case to earth ground for the

safest grounding procedure.

12. 6 PIN AMPHENOL: For attaching optional remote

control equipment to the GX 271.

13. 14 PIN AMPHENOL: For attaching wire feeder con-

trol cables to the GX 271 (Includes contactor closure

circuit, remote control circuit, wire feeder 115/42 volt

power source).

14. WIRE FEEDER VOLTMETER POLARITY SWITCH:

matches polarity of wire feeder voltmeter to polarity

of electrode.

15. ENGINE RUN-STOP SWITCH: Energizes engine cir-

cuit.

16. ENGINE START PUSHBUTTON SWITCH:

Energizes starter solenoid contactor and fuel sole-

noid.

17. ENGINE CHOKE

18. AUTO IDLER SWITCH: In the “AUTO” mode, the

engine goes to low idle speed 12 seconds after a

welding or auxiliary power load is removed. Engine

goes to high speed when the load is re-applied.

19. BATTERY CHARGER AMMETER

20. ENGINE HOUR METER

4 3

121413

GX 271 Chopper LPG

B-4

OPERATION

B-4

ENGINE OPERATION

DO NOT RUN THE ENGINE AT EXCESSIVE

SPEEDS. The maximum allowable high idle speed

for the GX 271 is 3750 RPM, no load. Do NOT adjust

the governor screw on the engine. Severe personal

injury and damage to the machine can result if it is

operated at speeds above the maximum rated speed.

------------------------------------------------------------------------

Read and understand all safety instructions included

in the Engine Owner’s manual that is shipped with

your GX 271.

BEFORE STARTING THE ENGINE

Check the engine oil level:

1. Be sure the machine is on a level surface.

2. Remove the engine oil dipstick and wipe it with a

clean cloth. Reinsert the dipstick and check the

level on the dipstick.

3. Add oil (if necessary) to bring the level up to the full

mark. Do not overfill.

4. See Engine Owner’s Manual for specific oil recom-

mendations.

WARNING

STARTING THE ENGINE

Be sure all Pre-Operation Maintenance has been per-

formed. See the INSTALLATION section.

Remove all loads connected to the AC power recepta-

cles and the welder before starting the engine.

------------------------------------------------------------------------

To start the engine, set the “IDLER” switch in the

“AUTO” ( / ) position.

Open the fuel valve on the supply cylinder. Pull the

choke control out.

Place the “Engine” Switch in the “RUN” Position.

Push the “Start” button and crank the engine until it

starts. Release the button as soon as the engine

starts. After the engine has started, slowly return the

choke control to the full “in” position (choke open). In

the “AUTO” position, the engine will run at high idle for

10-14 seconds and then go to low idle. Allow the

engine to warm up by letting it run at low idle for a few

minutes.

At cold temperatures, it may be necessary to start the

engine in “HIGH” idle and allow it to run for several

minutes before using “AUTO” idle.

Operating the starter motor for more than 5 seconds

can damage the motor. If the engine fails to start,

release the switch and wait 10 seconds before operat-

ing the starter again. Do not push the “Start” button

while the engine is running because this can damage

the ring gear and/or starter motor.

------------------------------------------------------------------------

CAUTION

La page charge ...

Lincoln Electric Red-D-Arc GX-271 Mode d'emploi

Marque: Lincoln Electric

Modèle: Red-D-Arc GX-271

Catégorie: Système de soudage

Taper: Mode d'emploi

Télécharger le PDF

rapport

dans d''autres langues

English: Lincoln Electric Red-D-Arc GX-271 Operating instructions

Lincoln Electric Red-D-Arc GX-271 Mode d'emploi

Lincoln Electric Red-D-Arc GX-271 Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents