Sony VPL-VW365 Guide de démarrage rapide

Marque: Sony

Modèle: VPL-VW365

Catégorie: Projecteurs de données

Taper: Guide de démarrage rapide

Ce manuel convient également à

VPL-VW665

VPL-VW665

VPL-VW365

VPL-VW665/VW365

4-580-175-02

(

)

M:\003\XP ML\4580175021_VPL-VW665_US-FR(7.1

600dpi)\4580175021_VPL-VW665_US-FR\01US-

VPLVW665UC\010COV.fm

masterpage:Ba ck

Cover

4-580-175-02 (1)

Video

Projector

Quick Reference Manual ____________ US

Guide de référence rapide __________ FR

VPL-VW665/VW365

4-580-175-01

(

)

F:\802728U_VPL-

VW665_QRM_US\4580175011\4580175011VPLVW665U8\050BCO.f

masterpage:Ba ck

Cover

Printed in Japan

This Quick Reference Manual explains the installation and basic operations for projecting

pictures. It also describes important notes and cautions to which you have to pay attention when

handling and using this unit.

Refer to “Warning Indicators” and “Replacing the Lamp,” as necessary.

For details on the operations, refer to the Operating Instructions contained in the supplied CD-

ROM.

About the Quick Reference Manual

Preparing ....................................................Page 9

Installing the Unit..................................Page 10

Connecting the Unit.............................Page 12

Selecting the Menu Language........Page 13

Projecting..................................................Page 14

Error Handling

Warning Indicators.........................................Page 16

Maintenance

Replacing the Lamp .......................................Page 17

Step 1

Step 2

Step 3

Step 4

Step 5

Before operating the unit, please read this

manual thoroughly and retain it for future

reference.

WARNING

To reduce the risk of fire or electric

shock, do not expose this apparatus

to rain or moisture.

To avoid electrical shock, do not open

the cabinet. Refer servicing to

qualified personnel only.

WARNING

THIS APPARATUS MUST BE

EARTHED.

WARNING

When installing the unit, incorporate a

readily accessible disconnect device in the

fixed wiring, or connect the power plug to an

easily accessible socket-outlet near the unit.

If a fault should occur during operation of

the unit, operate the disconnect device to

switch the power supply off, or disconnect

the power plug.

CAUTION

About the LAN connector

For safety, do not connect the connector for

peripheral device wiring that might have

excessive voltage to this port.

WARNING

1. Use the approved Power Cord (3-core

mains lead) / Appliance Connector / Plug

with earthing-contacts that conforms to

the safety regulations of each country if

applicable.

2. Use the Power Cord (3-core mains lead) /

Appliance Connector / Plug conforming

to the proper ratings (Voltage, Ampere).

If you have questions on the use of the above

Power Cord / Appliance Connector / Plug,

please consult a qualified service personnel.

As with any bright

light source, do not

stare into the beam,

RG2 IEC 62471-5:

2015.

For the customers in the U.S.A.

This equipment has been tested and found to

comply with the limits for a Class B digital

device, pursuant to part 15 of the FCC Rules.

These limits are designed to provide

reasonable protection against harmful

interference in a residential installation. This

equipment generates, uses and can radiate

radio frequency energy and, if not installed

and used in accordance with the instructions,

may cause harmful interference to radio

communications. However, there is no

guarantee that interference will not occur in

a particular installation. If this equipment

does cause harmful interference to radio or

television reception, which can be

determined by turning the equipment off and

on, the user is encouraged to try to correct

the interference by one or more of the

following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the

equipment and receiver.

- Connect the equipment into an outlet on a

circuit different from that to which the

receiver is connected.

- Consult the dealer or an experienced

radio/TV technician for help.

You are cautioned that any changes or

modifications not expressly approved in this

manual could void your authority to operate

this equipment.

All interface cables used to connect

peripherals must be shielded in order to

comply with the limits for a digital device

pursuant to Subpart B of part 15 of FCC

Rules.

This device complies with part 15 of the

FCC Rules. Operation is subject to the

following two conditions: (1) This device

may not cause harmful interference, and (2)

this device must accept any interference

received, including interference that may

cause undesired operation.

If you have any questions about this product,

you may call;

Sony Customer Information Service Center

1-800-222-7669 or http://www.sony.com/

This transmitter must not be co-located or

operating in conjunction with any other

antenna or transmitter.

For the customers in Canada

This device complies with Industry Canada

licence-exempt RSS standard(s). Operation

is subject to the following two conditions:

(1) this device may not cause interference,

and (2) this device must accept any

interference, including interference that may

cause undesired operation of the device.

For the customers in the U.S.A. and

Canada

Radiated Exposure Statement:

The product complies with the US/Canadian

portable RF exposure limit set forth for an

uncontrolled environment and is safe for

intended operation as described in this

manual. The further RF exposure reduction

can be achieved if the product can be kept as

far as possible from the user body or if the

device is set to lower output power if such

function is available.

For the customers in Canada

CAN ICES-3 (B)/NMB-3(B)

Caution on replacement/disposal of

the battery for the 3D glasses

Danger of explosion if battery is incorrectly

replaced.

Replace only with the same or equivalent

type recommended by the manufacturer.

When you dispose of the battery, you must

obey the law in the relative area or country.

Declaration of Conformity

Trade Name: SONY

Model: VPL-VW665

VPL-VW365

Responsible party: Sony Electronics Inc.

Address: 16535 Via Esprillo,

San Diego, CA 92127

U.S.A.

Telephone Number:858-942-2230

This device complies with part 15 of the

FCC Rules. Operation is subject to the

following two conditions: (1) This device

may not cause harmful interference, and

(2) this device must accept any interference

received, including interference that may

cause undesired operation.

For the customers in the U.S.A.

SONY LIMITED WARRANTY - Please

visit http://www.sony.com/psa/warranty

for important information and complete

terms and conditions of Sony’s limited

warranty applicable to this product.

For the customers in Canada

SONY LIMITED WARRANTY

- Please

visit http://www.sonybiz.ca/pro/lang/en/

ca/article/resources-warranty-product-

registration for important information

and complete terms and conditions of

Sony’s limited warranty applicable to this

product.

For the customers in Europe

Sony Professional Solutions Europe -

Standard Warranty and Exceptions on

Standard Warranty.

Please visit http://www.pro.sony.eu/

warranty for important information and

complete terms and conditions.

For the customers in Korea

SONY LIMITED WARRANTY

- Please

visit http://bpeng.sony.co.kr/handler/

BPAS-Start for important information

and complete terms and conditions of

Sony’s limited warranty applicable to this

product.

Precautions

On safety

• Check that the operating voltage of your

unit is identical with the voltage of your

local power supply.

• Should any liquid or solid object fall into

the cabinet, unplug the unit and have it

checked by qualified personnel before

operating it further.

• Unplug the unit from the wall outlet if it is

not to be used for several days.

• To disconnect the cord, pull it out by the

plug. Never pull the cord itself.

• The wall outlet should be near the unit and

easily accessible.

• The unit is not disconnected to the AC

power source (mains) as long as it is

connected to the wall outlet, even if the

unit itself has been turned off.

• Do not look into the lens while the lamp is

on.

• Do not place your hand or objects near the

ventilation holes. The air coming out is

hot.

On preventing internal heat build-

After you turn off the power with the ?/1

(ON/STANDBY) button, do not disconnect

the unit from the wall outlet while the

cooling fan is still running.

Caution

This unit is equipped with ventilation holes

(intake) and ventilation holes (exhaust). Do

not block or place anything near these holes,

or internal heat build-up may occur, causing

picture degradation or damage to the unit.

On repacking

Save the original shipping carton and

packing material; they will come in handy if

you ever have to ship your unit. For

maximum protection, repack your unit as it

was originally packed at the factory.

On watching 3D video images

Safety precautions

• You should only use the 3D glasses for

watching 3D video images.

• If you observe flickering or flashing, turn

off the lighting in the room.

• Not for use by children without proper

adult supervision.

• Be careful not to pinch your fingers in

hinges of the 3D glasses when bending the

temple frames.

• Do not drop or modify these 3D glasses.

• If these glasses are broken, keep broken

pieces away from your mouth or eyes.

On LCD Projector

The LCD projector is manufactured using

high-precision technology. You may,

however, see tiny black points and/or bright

points (red, blue, or green) that continuously

appear on the LCD projector. This is a

normal result of the manufacturing process

and does not indicate a malfunction.

Also, when you use multiple LCD projectors

to project onto a screen, even if they are of

the same model, the color reproduction

among projectors may vary, since color

balance may be set differently from one

projector to the next.

On condensation

If the room temperature where the projector

is installed changes rapidly, or if the

projector is moved suddenly from a cold to a

warm place, condensation in the projector

may occur. As the condensation may cause

malfunction, be careful in adjusting

temperature settings of the air conditioner. If

condensation occurs, leave the projector

turned on for about two hours before use.

Notes on security

• SONY WILL NOT BE LIABLE FOR

DAMAGES OF ANY KIND

RESULTING FROM A FAILURE TO

IMPLEMENT PROPER SECURITY

MEASURES ON TRANSMISSION

DEVICES, UNAVOIDABLE DATA

LEAKS RESULTING FROM

TRANSMISSION SPECIFICATIONS,

OR SECURITY PROBLEMS OF ANY

KIND.

• Depending on the operating environment,

unauthorized third parties on the network

may be able to access the unit. When

connecting the unit to the network, be sure

to confirm that the network is protected

securely.

• From a safety standpoint, when using the

unit connected with the network, it is

strongly recommended to access the

Control window via a Web browser and

change the access limitation settings from

the factory preset values (refer to “Using

Network Features” in the Operating

Instructions).

Changing the password regularly is also

recommended.

• Do not browse any other website in the

Web browser while making settings or

after making settings. Since the login

status remains in the Web browser, close

the Web browser when you complete the

settings to prevent unauthorized third

parties from using the unit or harmful

programs from running.

Notes on Installation

and Usage

Do not place the unit in the following

situations, which may cause malfunction or

damage to the unit.

Near walls

To maintain the performance and reliability

of the unit, leave space between walls and

the unit as illustrated.

Air from air conditioners or the ventilation

holes of this unit or other devices, may cause

oscillation on the screen. Be sure not to

install this unit in the area where the air from

air conditioners or the ventilation holes of

these devices reach to the front side of this

unit.

Poorly ventilated location

Leave space of more than 30 cm (11

inches) around the unit.

Note

SONY WILL NOT BE LIABLE FOR

DAMAGES OF ANY KIND

RESULTING FROM THE USE OF

THIS UNIT FOR PURPOSES OTHER

THAN GENERAL HOME USE,

EITHER DURING THE WARRANTY

PERIOD OR AFTER EXPIRATION OF

THE WARRANTY.

Unsuitable installation

1 cm (

inch)

30 cm

(11

inches)

30 cm

(11

inches)

15 cm

(6 inches)

30 cm

(11

inches)

30 cm

(11

inches)

Hot and humid

Locations subject to direct cool or

warm air from an air-conditioner

Installing the unit in such a location may

cause a malfunction of the unit due to

moisture condensation or rise in

temperature.

Near a heat or smoke sensor

Malfunction of the sensor may occur.

Very dusty and extremely smoky

locations

Do not do any of the following while using

the unit.

Tilting front/rear and left/right

Avoid using the unit tilted at an angle of

more than 15 degrees.

Do not install the unit anywhere other than

on a level surface or on the ceiling. Installing

the unit in such a location may result in

uneven color uniformity or reduce the

reliability of the effects of the lamp.

If the unit is tilted up or down, the image on

the screen may be trapezoidal.

Position the unit so that the lens is parallel to

the screen.

When installing the unit at high

altitudes

When using the unit at an altitude of

1,500 m (approx. 4,900 ft) or higher, set

“High Altitude Mode” on the Setup

menu to “On”. Failing to set this mode when

using the unit at high altitudes could have

Unsuitable Conditions

15° or more

15° or

15° or more

15° or

15° or more

adverse effects, such as reducing the

reliability of certain components.

• Never mount the projector on the ceiling

or move it by yourself. Be sure to consult

with qualified Sony personnel (charged).

• When installing the unit on a ceiling, be

sure to use a safety wire, etc., to prevent

the unit from falling. Entrust the

installation to an experienced contractor or

installer.

For dealers

• When the projector is mounted on the

ceiling, a Sony bracket or recommended

equivalent must be used for installation.

• Be sure to secure the cabinet cover firmly

when installing to the ceiling firmly.

Safety precautions for

installing the unit on a ceiling

Check the carton to make sure it contains the

following items:

• Remote control (1)

VPL-VW665: RM-PJ24

VPL-VW365: RM-PJ28

• Size AA (R6) manganese batteries (2)

• Lens cap (1)

When you purchase the projector, a lens

cap is on the lens. Remove the lens cap

before you use the projector.

• AC power cord (1)

• Quick Reference Manual (this manual) (1)

• Operating Instructions (CD-ROM) (1)

CAUTION

Danger of explosion if battery is incorrectly

replaced.

Replace only with the same or equivalent

type recommended by the manufacturer.

When you dispose of the battery, you must

obey the law in the relative area or country.

Caution

Two size AA (R6) batteries are supplied for

Remote Control.

To avoid risk of explosion, use size AA (R6)

manganese or alkaline batteries.

Caution about handling the remote

control

• Handle the remote control with care. Do

not drop or step on it, or spill liquid of any

kind onto it.

• Do not place the remote control in a

location near a heat source, a place subject

to direct sunlight, or a damp room.

The manual can be read on a computer with

Adobe Reader installed.

You can download Adobe Reader free from

the Adobe website.

1 Open the index.html file in the CD-

ROM.

2 Select and click on the manual that

you want to read.

If you have lost or damaged the CD-ROM, you

can purchase a new one from your Sony dealer

or Sony service counter.

Preparing

Step 1

Checking the Supplied

Accessories

Inserting the Batteries into

the Remote Control

Push and slide to

open.

Insert the batteries E

side first.

Using the CD-ROM manual

Note

1 Position the unit so that the lens is

parallel to the screen.

2 After connecting the AC power cord to

the unit, plug the AC power cord into

a wall outlet.

After connecting the AC power cord to the unit,

the ON/STANDBY indicator may blink in

orange.

You may not be able to control the unit while

the indicator is blinking, but this is not a

malfunction. Wait until it stops blinking and

remains lit in red.

3 Press the ?/1 (ON/STANDBY) button

to turn on the unit.

4 Project an image on the screen, then

adjust the focus, size, and position.

VPL-VW665

a Adjust the focus.

Press the LENS ADJUSTMENT

(FOCUS) button to display the Lens

Focus adjustment window (test pattern).

Then adjust the focus of the picture by

pressing the M/m/</, buttons.

b Adjust the picture size.

Press the LENS ADJUSTMENT

(ZOOM) button to display the Lens

Zoom adjustment window (test pattern).

Then adjust the size of the picture by

pressing the M/m/</, buttons.

c Adjust the picture position.

Press the LENS ADJUSTMENT

(SHIFT) button to display the Lens Shift

adjustment window (test pattern). Then

adjust to the proper position of the

picture by pressing the M/m/</,

buttons.

Installing the Unit

Step 2

Note

Lights in red.

Front of the unit

Flashes in green for

tens of seconds and

then lights in green.

Front of the unit

VPL-VW365

a Adjust the focus.

Press the PATTERN button repeatedly to

display the Lens Focus adjustment

window (test pattern). Then adjust the

focus of the picture by pressing the M/m/

</, buttons.

b Adjust the picture size.

Press the PATTERN button repeatedly to

display the Lens Zoom adjustment

window (test pattern). Then adjust the

size of the picture by pressing the M/m/

</, buttons.

c Adjust the picture position.

Press the PATTERN button repeatedly to

display the Lens Shift adjustment

window (test pattern). Then adjust to the

proper position of the picture by

pressing the M/m/</, buttons.

Lens adjustment window (test

pattern)

1.78:1 (16:9)

2.35:1

1.85:1

1.33:1 (4:3)

The dashed lines show the screen sizes of each

aspect ratio.

For more information, refer to

“Connections and Preparations” in the

Operating Instructions contained in the

supplied CD-ROM.

When making connections, be sure to do the following:

• Turn off all equipment before making any connections.

• Use the proper cables for each connection.

• Insert the cable plugs properly; poor connection at the plugs may cause a malfunction or poor

picture quality. When pulling out a cable, be sure to pull it out from the plug, not the cable

itself.

• Refer to the operating instructions of the connected equipment.

Connecting the Unit

Step 3

Right side of the unit

AV amplifier

Speakers

Equipment with HDMI

output connectors

Computer

to HDMI output

HDMI cable (not supplied)

: Video signal flow Use a high speed HDMI cable on which the cable type logo

is specified. (Sony products are recommended.)

For more information, refer to “Connections and

Preparations” in the Operating Instructions contained in

the supplied CD-ROM.

You can select the language for displaying

the menu and other on-screen displays. The

factory default setting is English. To change

the current menu language, set the desired

language with the menu screen.

1 Press MENU.

The menu appears.

2 Press M/m to select the Setup

menu, and press , or .

The setting items of the selected menu

appear.

3 Press M/m to select “Language,” and

press , or .

4 Press M/m/</, to select a

language, and press .

The menu changes to the selected

language.

To clear the menu

Press MENU.

Selecting the Menu Language

Step 4

1 Turn on both the unit and the

equipment connected to the unit.

2 Press INPUT to display the input

palette on the screen.

3 Select the equipment from which you

want to display images.

Press INPUT repeatedly or press M/m/

(enter) to select the equipment from

which to project.

1 Press the ?/1 (ON/STANDBY)

button.

A message “POWER OFF?” appears on

the screen.

2 Press the ?/1 (ON/STANDBY) button

again before the message disappears.

The ON/STANDBY indicator flashes in

green and the fan continues to run to

reduce the internal heat.

The fan stops and the ON/STANDBY

indicator changes from flashing green to

remaining red.

The power is turned off completely, and you

can disconnect the AC power cord.

Never disconnect the AC power cord while the

indicator is flashing.

You can turn off the unit by holding the ?/1

(ON/STANDBY) button for about 1 second,

instead of performing the above steps.

Projecting

Step 5

Projecting the Picture

Turning Off the Power

Example: To view the picture from the

video equipment connected to the HDMI

1 connector of this unit.

Note

For more information, refer to

“Projecting” in the Operating Instructions

contained in the supplied CD-ROM.

Press one of the CALIBRATED PRESET

buttons.

Selecting the Picture Viewing Mode

CALIBRATED

PRESET buttons

Setting items Description

CINEMA FILM 1 Picture quality suited to reproducing the highly dynamic and

clear images typical of master positive film.

CINEMA FILM 2 Picture quality suited for HDR content, with the highest

dynamic range and many colors.

REF A picture quality setup suitable for when you want to reproduce

faithfully the original image quality, or for enjoying image

quality, without any adjustment.

TV Picture quality suited for watching TV programs, sports,

concerts, and other video images.

PHOTO Ideal for projecting still images taken with a digital camera.

GAME Picture quality suited to gaming, with well-modulated colors

and fast response.

BRT CINE Picture quality suited for watching movies in a bright

environment, such as a living room.

BRT TV Picture quality suited for watching TV programs, sports,

concerts, and other video images in a bright environment, such

as a living room.

USER Adjusts the picture quality to suit your taste then saves the

setting. The factory default setting is the same as “REF.”

For more information, refer to “Projecting” in the

Operating Instructions contained in the supplied CD-

ROM.

The ON/STANDBY or WARNING indicator lights up or flashes if there is any trouble with

your projector.

When a warning indicator other than the above starts flashing, and the symptom persists even after

carrying out the above methods, consult with qualified Sony personnel.

Error Handling

Warning Indicators

Flashing/Lighting indicators The number of

flashes

Cause and Remedy

Twice Close the lamp cover securely, then tighten

the screws securely.

Three times The temperature of lamp is unusually high.

Turn off the power and wait for the lamp to

cool, then turn on the power again.

If the symptom persists, the lamp may be at

the end of its service life. In this case,

replace the lamp with a new one.

Twice The internal temperature is unusually high.

Check to ensure that if nothing is blocking

the ventilation holes or whether or not the

unit is being used at high altitudes.

Three times The fan is broken. Consult with qualified

Sony personnel.

Note

ON/STANDBY

indicator

WARNING

indicator

(Flashes in red)

Both indicators flash

If there is any problem or an error message appears on the

screen, refer to “Error Handling” in the Operating

Instructions contained in the supplied CD-ROM.

The lamp used for the light source has a

certain lifespan. When the lamp dims, the

color balance of the picture becomes

strange, or “Please replace the Lamp.”

appears on the screen, the lamp may be

exhausted. Replace the lamp with a new one

(not supplied) without delay.

Tip

The lifespan of the lamp used for the light

source changes depending on the installation

environment or use conditions. You can use the

lamp longer by avoiding turning the lamp off

until several minutes pass after turning the

lamp on.

Tools you need to get started:

• Projector Lamp (Optional)

VPL-VW665: LMP-H280

VPL-VW365: LMP-H220

• Standard Phillips screwdriver

• Cloth (for scratch protection)

Caution

• The lamp remains hot after the unit is

turned off with the ?/1 (ON/STANDBY)

button. If you touch the lamp, you may

burn your fingers. When you replace the

lamp, wait for at least 1 hour for the lamp

to cool.

• Do not touch the surface of the lamp. If

you touch it, wipe off the fingerprints with

a soft cloth.

• Pay special attention to replacing the lamp

when the unit is installed on the ceiling.

• When replacing the lamp of a unit which is

on the ceiling, do not stand directly under

the lamp cover. When removing the lamp

door (inner cover), avoid twisting it. If the

lamp explodes, fragments may cause

injury.

• When removing the lamp unit, make sure

it remains horizontal, then pull straight up.

Do not tilt the lamp unit. If you pull out the

lamp unit while tilted and if the lamp

breaks, the pieces may scatter, causing

injury.

• Be sure to use a specified projector lamp for

the replacement. If you use lamps other than

the specified projector lamp, the unit may

malfunction.

• Be sure to turn off the unit and unplug the

power cord before replacing the lamp, then

check the ON/STANDBY indicator has

already been turned off.

1 Turn off the unit and unplug the AC

power cord.

2 When setting the unit on a flat surface

such as a desk etc., put a cloth to

prevent the surface from being

scratched. Place the unit on the cloth.

Be sure that the unit is placed on a stable

surface.

3 While pressing the part indicated

in the lamp cover illustration, slide 1

and then open 2 the lamp cover.

4 Loosen the lamp door (inner cover)

screw with a Phillips screwdriver, and

then open the lamp door.

Maintenance

Replacing the Lamp

Notes

Note

5 Loosen the 3 screws on the lamp with

the Phillips screwdriver. Hold up the

handle, then pull the lamp straight out.

• Do not loosen other screws except the 3

specified screws.

• Hold the lamp by the handle to remove

and attach it.

6 Push in the new lamp by the handle

securely until it reaches the end, and

then tighten the 3 screws.

Be careful not to touch the optical block

inside the unit.

7 Close the lamp door (inner cover), and

then tighten the screw.

8 Close the lamp cover.

Notes

Handle

Note

9 Wipe dust off the ventilation holes

(intake) with a soft cloth.

10Turn on the unit, then select the lamp

setting item on the Setup menu.

The menu screen below will be

appeared.

Tip

If “Settings Lock” is set to “Level B,” set to

“Off” once.

11Select “Yes.”

Caution

Do not put your hands into the lamp

replacement slot, and do not allow any liquid

or other objects into the slot to avoid

electrical shock or fire.

• The unit will not turn on unless the lamp is

securely installed in place.

• The unit will not turn on unless the lamp

cover are securely closed.

• To clear a message displayed on the screen,

press any button either on the remote control

or the control panel of the unit once.

Note on replacing the lamp when

broken, in the case of a ceiling

installation

If the lamp breaks, broken lamp pieces may

scatter and cause injury.

When the unit is on the ceiling, remove the

lamp door (inner cover) by sliding it

horizontally slowly after raising it with 30

degree opened. Avoid twisting the lamp door

(inner cover).

Disposal of the used lamp

Notes

Ventilation holes

(intake)

Note

The lamp contains mercury. The disposal

rules for used fluorescent tubes depend on

where you live. Follow the waste disposal

policy in your area.

For the customers in

the U.S.A. and Canada

Lamp contains

mercury. Dispose

according to applicable

local, state/province and

federal laws.

For additional information,

see www.sony.com/

mercury

Ce Guide de référence rapide décrit l’installation et les procédures de base de projection des

images. Vous y trouverez également des mises en garde et des remarques importantes qu’il

convient de respecter au cours de la manipulation et de l’utilisation de cet appareil.

Reportez-vous à « Indicateurs d’avertissement » et « Remplacement de la lampe », le cas

échéant.

Pour plus d’informations sur l’utilisation, reportez-vous au Mode d’emploi que vous trouverez

sur le CD-ROM fourni.

A propos du Guide de référence rapide

Préparation ................................................Page 8

Installation de l’appareil ......................Page 9

Raccordement de l’appareil.............Page 11

Sélection de la langue du menu ....Page 12

Projection..................................................Page 13

Gestion des

erreurs

Indicateurs d’avertissement ..........................Page 15

Entretien

Remplacement de la lampe............................Page 16

Etape 1

Etape 2

Etape 3

Etape 4

Etape 5

La page charge ...

Sony VPL-VW365 Guide de démarrage rapide

Marque: Sony

Modèle: VPL-VW365

Catégorie: Projecteurs de données

Taper: Guide de démarrage rapide

Ce manuel convient également à

VPL-VW665

Télécharger le PDF

rapport

dans d''autres langues

English: Sony VPL-VW365 Quick start guide

Sony VPL-VW365 Guide de démarrage rapide

Ce manuel convient également à

Sony VPL-VW365 Guide de démarrage rapide

dans d''autres langues

Documents connexes