Yealink W52H Guide de démarrage rapide

IP DECT Phone

W52P & W52H

Quick Start Guide(V73.16)

www.yealink.com

Applies to rmware version 25.73.0.11 or later.

English | Deutsch | Español | Français

Table of Contents

English .................................................. 1

Deutsch...............................................13

Español................................................25

Français ...............................................36

Packaging Contents

The following items are included in your W52P package:

Handset

Base Station

Charger Cradle

(Optional)

Two Power Adapters

Belt Clip

Ethernet Cable

Two Rechargeable Batteries

Quick Start Guide

The following items are included in your W52H package:

Handset

Charger Cradle

Power Adapter

Belt Clip

Two Rechargeable

Batteries

Assembling the Phone

1. Connect the network and power for the base station in one of the following ways, as shown below:

a. AC Power Option

1

b. PoE (Power over Ethernet) Option

IEEE 802.3af compliant

PoE Hub/Switch

2. Connect the charger cradle, as shown below:

3. Insert the batteries into the handset, as shown below:

4. Charge the handset, as shown below:

Note: The IP DECT phone should be used with Yealink original power adapter (5V/600mA) only. The charging status of the

handset is indicated on the top right-hand corner of the LCD screen.

2

Handset Registration

The handset in the W52P package is pre-registered to the base station. Internal handset number and name display on

the idle screen after turning the handset on. If your handset is not pre-registered to the base station, do one of the

followings to register it manually:

 If the handset LCD screen prompts “Searching for Base”, long press on the base station till the registration LED ﬂashes.

Then press the OK key to enter the main menu, and then select Settings->Registration->Register Handset to register the

handset.

 If the handset LCD screen prompts “Press base page 2s then press OK”, long press on the base station till the

registration LED ﬂashes. Then press the OK soft key on the handset.

Shortcuts

This helps you get quick access to features by pressing the shortcut keys directly without having to scroll through the

menu.You can press the following predeﬁned shortcuts to access some frequently used features of your handset when

the handset is idle:

 Press to access the call history.

 Press to check the line status.

 Press to place an internal call.

 Press to access the directory.

 Press to decrease the ringer volume.

 Press to increase the ringer volume.

Getting Started

Network Settings

You can conﬁgure the base station to obtain network settings in one of the following ways:

DHCP By default, the base station attempts to contact a DHCP server in your network to obtain the valid network

settings, e.g., IP address, subnet mask, gateway addres and DNS address.

Static If the base station cannot contact a DHCP server for any reason, you need to conﬁgure the IP address,

subnet mask, gateway address, primary DNS address and secondary DNS address for the base station

manually.

PPPoE: If you are using an xDSL modem, you can connect your phone to the Internet via PPPoE mode. Contact the

ITSP for the account and password.

To conﬁgure the network parameters for the base station manually:

1. Press the OK key to enter the main menu, and then select Settings->System Settings -> Network.

2. Enter the system PIN (default: 0000), and then press the Done soft key.

3. Select desired type from the IP Address Type ﬁeld.

4. Make the desired changes.

5. Press the Save soft key to accept the change.

Note: The wrong network settings may result in inaccessibility of your phone and may have an impact on the network Performance.

For more information on these parameters, contact your systme administrator.

3

Handset Name

To rename the handset:

1. Press the OK key to enter the main menu, and then select Settings->Handset Name.

2. Edit the value in the Rename ﬁeld.

3. Press the Save soft key to accept the change.

Volume Adjustment

 Press or during a call to adjust the volume of the currently used audio device.

 Press or when the handset is idle to adjust the ringer volume.

Ring Tones

1. Press the OK key to enter the main menu, and then select Settings->Audio->Ring Tones ->Melodies.

2. Press or to highlight the Intercom Call option or the desired line.

3. Press or to select the desired ring tone.

4. Press the Save soft key to accept the change.

Local Directory

To add a contact:

1. Press the OK key to enter the main menu, and then select Directory.

2. Press the Options soft key, and then select New Contact.

3. Enter the desired values in the Name, Number and Mobile ﬁelds.

4. Press the Save soft key to accept the change.

To edit a contact:

1. Press the OK key to enter the main menu, and then select Directory.

2. Press or to highlight the desired entry.

Turning Handset On/Oﬀ

To turn the handset on, do one of the following:

 Long press until the LCD screen lights up.

 Place the handset in the charger cradle. The handset will be turned on automatically.

To turn the handset oﬀ:

Long press again to turn the handset oﬀ.

Locking/Unlocking Keypad

 Long press when the phone is idle to lock the keypad.

 Long press again when the phone is idle to unlock the keypad.

Switching Silent Mode On/Oﬀ

 Press to switch the silent mode on.

 Press again to switch the silent mode oﬀ.

Basic Operations

Handset Settings

4

Placing Calls

To place a call directly:

Enter the desired number when the handset is idle, and then press .

To place a call from the local directory:

1. Press when the handset is idle.

2. Press or to highlight the desired entry, and then press .

If both the oﬃce number and mobile number are stored, press or to highlight the desired number, and

then press again.

To place a call from the call history:

1. Press the History soft key, and then select the desired call history list.

2. Press or to highlight the desired entry, and then press .

To place a call from the redial number list:

1. Press when the handset is idle.

2. Press or to highlight the desired entry, and then press .

To place a call using the speed dial key:

Long press the speed dial key to place a call to the number assigned to it.

Answering Calls

To answer a call, do one of the following:

 Press the Accept soft key.

 Press .

3. Press the Options soft key, and then select Edit.

4. Edit the values in the Name, Numberand Mobile ﬁelds.

5. Press the Savesof t key to accept the change.

To delete a contact:

1. Press the OK key to enter the main menu, and then select Directory.

2. Press or to highlight the desired entry.

3. Press the Options soft key, and then select Deleteto delete the selected entr y.

To assign a speed dial number:

1. Press the OK key to enter the main menu, and then select Settings->Telephony->Speed Dial.

2. Press or to highlight the desired speed dial key, and then press the Assignsof t key.

3. Press or to highlight the desired entry, and then press the OK soft key.

If both the oﬃce number and mobile number are stored, press or to highlight the desired number, and

then press the OK soft key again.

Basic Call Features

Note: You can ignore an incoming call by pressing the Silence soft key or reject an incoming call by pressing .

Ending Calls

 Press .

5

Call Mute

 Press during a call to mute the call.

 Press again to un-mute the call.

Call Hold and Resume

To place a call on hold:

Press the Options soft key during a call, and then select Hold.

To resume a call, do one of the following:

 If there is only a call on hold, press the Resume soft key.

 If there are two calls on hold, press the Resume soft key to resume the current call, press the Swap soft key to swap

between calls.

Call Transfer

You can transfer a call in the following ways:

Blind Transfer

1. Press the Options soft key during a call, and then select Transfer.

2. Enter the number you want to transfer the call to.

3. Press the Transfer soft key.

Semi-Attended Transfer

1. Press the Options soft key during a call, and then select Transfer.

2. Enter the number you want to transfer the call to.

3. Press to dial out.

4. Press the Transfer soft key when you hear the ring-back tone.

Attended Transfer

1. Press the Options soft key during a call, and then select Transfer.

2. Enter the number you want to transfer the call to.

3. Press to dial out.

4. Press the Transfer soft key after the call is answered.

Call Forward

To enable the call forward feature on a speciﬁc line:

1. Press the OK key to enter the main menu, and then select Call Features->Call Forward.

2. Press or to highlight the desired line, and then press the OK soft key.

3. Press or to highlight the desired forwarding type, and then press the OK soft key.

AlwaysIncoming calls are for warded immediately.

BusyIncoming calls are for warded when the line is busy.

No AnswerIncoming calls are for warded if not answered after a period of time.

4. Select Enabled from the Status ﬁeld.

5. Enter the number you want to forward the incoming calls to in the Target ﬁeld.

6. Press or to select the desired ring time to wait before forwarding (only for No Answer Forward) in the After Ring

Time ﬁeld.

7. Press the Save soft key to accept the change.

6

Safety Instructions

Save these instructions. Read these safety instructions before use!

To reduce risk of ﬁre, severe personal injury and damage to property, read the following safety

information carefully before using the product.

Environmental Requirements

 Place the product on a stable, level and non-slip surface.

 Do not place the product close to heat sources, in direct sunlight or next to any household

appliance with strong magnetic ﬁeld or electromagnetic ﬁeld, such as a microwave oven or a

refrigerator.

 Do not allow the product to come into contact with water, dust and chemicals.

 Protect the product from aggressive liquids and vapors.

 Do not place the product on or near any inﬂammable or ﬁre-vulnerable object, such as rubbermade

materials.

 Do not install the product in rooms with high humidity, for example, in bathrooms, laundry

rooms and wet basements.

Safety Notes During Operation

 Use only spare parts and accessories supplied or authorized by Yealink. The operation of

nonauthorized parts cannot be guaranteed.

 Do not place heavy objects on top of the handset or the base station in case of damage and

deformation caused by the heavy load.

 Do not open the handset or the base station by yourself for repair purpose, which could expose

you to high votages. Have all repairs carried out by authorized service personel.

 Do not let a child operate the product without guidance.

 Keep the small accessories contained in your product out of reach of small children in case of

accidental swallowing.

 Before plugging or unplugging any cable, make sure that your hands are completely dry.

 Do not hold the handset up to your ear when speakphone is on or when the ringer is ringing as

the volumn can be very loud, which may be harmful to your hearing.

 During a thunderstorm, stop using the product and disconnect it from the power supply to avoid

lightning strike.

 If the product is left unused for a rather long time, disconnect the base station from the power

supply and unplug the power adapter.

 When there is smoke emitted from the product, or some abnormal noise or smell, disconnect the

product from the power supply, and unplug the power adapter immediately.

 Remove the electrical cord from an outlet by pulling gently on the power adapter, not by pulling

the cord.

7

Battery Precautions

 Do not immerse the battery into water, which could short-circuit and damage the battery.

 Do not expose the battery to an open ﬂame or leave the battery where it could be subjected to

extremly high temperatues, which could cause the battery to explode.

 Do power the handset oﬀ before removing the battery.

 Do not try to use the battery for the power supply of any device other than this handset.

 Do not open or mutilate the battery, released electrolyte is corrosive and may cause damage to

the your eyes or skin.

 Use only the rechargeable battery pack delivered with the handset or those rechargeable battery

packs expressly recommended by Yealink.

 Defective or exhausted battery should never be disposed of as municipal waste. Return old

battery to the battery supplier, a licensed battery dealer or a designated collectio

n facility.

Notices of Cleaning

 Before cleaning the base station, stop using it and disconnect it from the power supply.

 Remove the battery before cleaning the handset to reduce risk of electric shock.

 Only clean your product with a piece of slightly moist and anti-static cloth.

 Keep the power plug clean and dry. Using a dirty or wet power plug may lead to electric shock or

other perils.

8

ENVIRONMENTAL RECYCLING

Never dispose of the device with domestic waste

Ask your Town Council about how to dispose of it in an environmentally friendly way.

The cardboard box, plastic packaging and player components may be recycled in

accordance with prevailing recycling regulations in your country.

Always adhere to prevailing regulations

Those who fail to do so may be ﬁned or prosecuted in accordance with the law.

The crossed out garbage can that appears on the device means that when it has

reached the end of its useful life, it should be taken to a special waste disposal centre

and treated separately to general urban waste.

Batteries: Be sure that the batteries have been placed in the right position. This phone use rechargeable

batteries only.

Compulsory information according to regulations for battery-operated devices. Caution: Risk of explosion

if battery is replaced with a battery of a wrong kind. Dispose of batteries in accordance with the

instructions.

Addr: 309, 3th Floor, No.16, Yun Ding North Road,

Huli District, Xiamen City, Fujian, P.R. China

Tel: +86-592-5702000

Fax: +86-592-5702455

9

YEALINK (XIAMEN) NETWORK TECHNOLOGY CO.,LTD

WWW.YEALINK.COM

Addr: 309, 3th Floor, No.16, Yun Ding North Road,

Huli District, Xiamen City, Fujian, P.R. China

Tel: +86-592-5702000

Fax: +86-592-5702455

10

Declaration of Conformity

We,

YEALINK(XIAMEN) NETWORK TECHNOLOGY CO.,LTD,

Address: 309, 3th Floor, No.16, Yun Ding North Road,

Huli District, Xiamen City, Fujian, P.R. China

CE DATE: 17th/July/2017

declare that the product

Type: IP DECT Phone

Model: W52P/W52H

meets the essential requirements and other relevant provisions according to the following EC directive

Directive: Radio Equipment Directive 2014/53/EU;

The presumption of conformity with the essential requirement is ensure according to:

Article 3.1 a : (protection of the health &the safety of the user)

Safety: EN 60950-1:2006+A11:2009+A1:2010+A12:2011+A2:2013

SAR: EN62479:2010

Article 3.1 b : (protection requirement with respect to electromagnetic compatibility)

EMC: ETSI EN 301489-1 V2.2.0 & ETSI EN 301489-6 V2.2.0

Article 3.2 (eﬀective use of the radio spectrum)

Radio: ETSI EN 301406 V2.2.2

YEALINK (EUROPE) NETWORK TECHNOLOGY B.V.

Address: Strawinskylaan 3127, Atrium Building, 8th ﬂoor,

1077ZX Amsterdam, the Netherlands

Telephone: +31(0)646111373

Email: [email protected]

Directive 2011/65/EU of the European Parliament and of the Council of 8 June 2011 on the

restriction of the use of certain hazardous substances in electrical and

electronic equipment (RoHS)

Directive 2002/96/EC of the European Parliament and of the Council of 27.01.2003 on Waste

electrical and electronic equipment(WEEE)

About us

Founded in 2001, Yealink, a leading provider of VoIP Phone and IP communication solutions, has been focusing on VoIP products

characterized by reliable quality, easy deployment and aﬀordable price for more than a decade. Today, customers rom over 140 countries

rely on Yealink as the backbone of global collaboration to extend the value of network communications.

More about Yealink

Since 2001, Yealink has continued to develop state-of-the art, hi-tech VoIP communication terminals that include IP video phones,

IP phones and USB phones. With a worldwide market in more than 140 countries, the company has also established a ﬁrst-class

international service network.

Our priorities are quality, functionality, ease-of-use, customer support and competitive pricing. To provide new solutions for the future

in this fast-evolving sector, Yealink’s large, talented and highly-experienced VoIP R&D team is totally committed to the pursuit of

excellence.

To date, we have passed more than 80 interoperability tests and meet certiﬁcation requirements set by leading VoIP system and platforms.

Yealink works in close partnership with T-Mobile, Telefonica, Portugal Telecom and other leading telecommunication service providers.

YEALINK(XIAMEN) NETWORK TECHNOLOGY CO.,LTD.

Web: www.yealink.com

Addr: 309, 3th Floor, No.16, Yun Ding North Road,

Huli District, Xiamen City, Fujian, P.R. China

Packaging Contents

Verpackungsinhalt

Folgende Teile sind im Lieferumfang Ihres W52P enthalten:

Hörer Basisstation Ladestation

(Optional)

Zwei Netzgeräte

Gürtelclip

Ethernet-Kabel

Zwei wiederauﬂadbare

Batterien

Erste Schritte

Folgende Teile sind im Lieferumfang des W52H enthalten:

Hörer

Ladestation

Netzgerät

Gürtelclip

Zwei wiederauﬂadbare

Batterien

Installation des Telefons

1. Verbinden Sie die Basisstation mit dem Netzwerk und der Stromversorgung gemäß einer der

nachfolgend beschriebenen Vorgehensweisen:

a. AC Stromversorgung

13

b. PoE (Power over Ethernet)

2. Verbinden Sie die Ladestation wie nachfolgend dargestellt:

3. Legen Sie die Batterien wie unten dargestellt in den Hörer ein:

4. Laden Sie den Hörer wie unten dargestellt auf:

Hinweis: Das IP-Telefon darf nur mit dem originalen Yealink Netzteil (5V/600mA) genutzt werden. Die Verwendung eines

Netzteiles eines Drittanbieters kann zu einer Beschädigung des Telefons führen.Den Ladestatus des Hörers

können Sie oben rechts im LCD nachverfolgen.

14

PoE Netzwerk-Switch

Registrierung des Hörers

Der Hörer des W52P-Sets wurde bereits an der Basisstation registriert. Nach dem Einschalten des Hörers werden auf

dem Ruhebildschirm die interne Hörernummer und der Name angezeigt. Falls Ihr Hörer nicht an der Basisstation

registriert wurde, führen Sie einen der nachfolgenden Schritte aus, um den Hörer manuell zu registrieren:

 Falls auf dem LCD des Hörers die Nachricht „Searching for Base“ erscheint, halten Sie die Taste an der Basisstation

gedrückt, bis die erste LED anfängt zu blinken. Drücken Sie dann die Taste OK zum Öﬀnen des Hauptmenüs und wählen Sie

Settings->Registration->Register Handset zur Registrierung des Hörers.

 Falls auf dem LCD des Hörers die Nachricht „Press base page 2s then press OK“ erscheint, halten Sie die Taste an der

Basisstation gedrückt, bis die erste LED anfängt zu blinken. Drücken Sie dann die Bildschirmtaste OK am Hörer.

Verknüpfungen

Verschaﬀen Sie sich schnellen Zugriﬀ auf Funktionen, indem Sie direkt auf die Verknüpfungen drücken und nicht endlos

durch das Menü scrollen. Drücken Sie im Ruhemodus Ihres Hörers auf eine der voreingestellten Verknüpfungen, um auf

einige häuﬁg verwendete Funktionen zuzugreifen:

 Drücken Sie , um das Anrufprotokoll anzuzeigen.

 Drücken Sie , um den Status der Leitung zu überprüfen.

 Drücken Sie , um einen internen Anruf zu tätigen.

 Drücken Sie , um das Verzeichnis aufzurufen.

 Drücken Sie , um die Lautstärke des Klingeltons zu reduzieren.

 Drücken Sie , um die Lautstärke des Klingeltons zu erhöhen.

Erste Schritte

Netzwerkeinstellungen

Zum Beziehen der Netzwerkeinstellungen können Sie die Basisstation anhand einer der nachfolgenden Möglichkeiten

konﬁgurieren:

DHCP Per Standardeinstellung kontaktiert die Basisstation einen DHCP-Server in Ihrem Netzwerk, um die gültigen

Netzwerkeinstellungen zu beziehen, z.B. IP-Adresse, Subnetzmaske, Gateway-Adresse und DNS-Adresse.

Static Falls die Basisstation aus irgendeinem Grund keinen DHCP-Server kontaktieren kann, müssen Sie die

IP-Adresse, Subnetzmaske, Gateway-Adresse, primäre DNS-Adresse und sekundäre DNS-Adresse für die

Basisstation manuell konﬁgurieren.

Manuelle Konﬁguration der Netzwerkeinstellungen für die Basisstation:

1. Drücken Sie die Taste OK zum Öﬀnen des Hauptmenüs und wählen Sie dann Settings->System Settings-> Network.

2. Geben Sie die System-PIN ein (Fabrikeinstellung: 0000) und drücken Sie dann auf die Bildschirmtaste Done.

3. Wählen Sie im Feld IP Address Type die Option Static.

4. Geben Sie in die Felder IP Address, Subnet Mask, Default Gateway, Primary DNS und Secondary DNS die entsprechenden Werte ein .

5. Drücken Sie die Bildschirmtaste Save zur Übernahme der Änderungen.

Hinweis: Falsche Netzwerkeinstellungen können zur Unzugänglichkeit Ihres Telefons und zu einer Beeinträchtigung der

Netzwerkleistung führen. Kontaktieren Sie Ihren Systemadministrator für weitere Informationen über diese

Einstellungen.

15

Hörername

Hörer umbenennen:

1. Drücken Sie die Taste OK zum Öﬀnen des Hauptmenüs und wählen Sie dann Settings->Handset Name.

2. Konﬁgurieren Sie im Feld Rename den aktuellen Eintrag.

3. Drücken Sie die Bildschirmtaste Save zur Übernahme der Änderungen.

Lautstärke einstellen

 Drücken Sie während eines Anrufs die Taste oder , um die Lautstärke des aktuellen Audiogeräts einzustellen.

 Drücken Sie im Ruhemodus des Hörers die Taste oder , um die Lautstärke des Klingeltons einzustellen.

Klingeltöne

1. Drücken Sie die Taste OK zum Öﬀnen des Hauptmenüs und wählen Sie dann Settings->Audio->Ring Tones-> Melodies.

2. Wählen Sie mit den Tasten oder die Option Intercom Call oder die gewünschte Leitung.

3. Wählen Sie mit den Tasten oder den gewünschten Klingelton aus.

4. Drücken Sie die Bildschirmtaste Save zur Übernahme der Änderungen.

Lokales Verzeichnis

Kontakt hinzufügen:

1. Drücken Sie die Taste OK zum Öﬀnen des Hauptmenüs und wählen Sie dann Directory.

2. Drücken Sie die Bildschirmtaste Options und wählen Sie dann New Contact.

3. Geben Sie in die Felder Name, Number und Mobile die entsprechenden Daten ein.

4. Drücken Sie die Bildschirmtaste Save zur Übernahme der Änderungen.

Kontakt bearbeiten:

1. Drücken Sie die Taste OK zum Öﬀnen des Hauptmenüs und wählen Sie dann Directory.

2. Wählen Sie mit oder den gewünschten Eintrag.

Hörer ein-/ausschalten

Schalten Sie den Hörer wie folgt ein:

 Halten Sie die Taste gedrückt, bis sich das LCD einschaltet.

 Setzen Sie den Hörer in die Ladestation. Der Hörer schaltet sich automatisch ein.

Hörer ausschalten:

Halten Sie die Taste erneut gedrückt, um den Hörer auszuschalten.

Tastatur sperren/entsperren

 Halten Sie die Taste gedrückt, um die Tastatur zu sperren.

 Halten Sie die Taste erneut gedrückt, um die Tastatur zu entsperren.

Lautlosen Modus aktivieren/deaktivieren

 Halten Sie die Taste gedrückt, um den lautlosen Modus zu aktivieren.

• Halten Sie die Taste erneut gedrückt, um den lautlosen Modus zu deaktivieren.

Grundlegende Funktionen

Hörereinstellungen

16

La page charge ...

Yealink W52H Guide de démarrage rapide

Ce manuel convient également à

Yealink W52H Guide de démarrage rapide

dans d''autres langues

Documents connexes