BIXOLON BGT-100Pt Manuel utilisateur

User’s Manual

BGT-100P/102P

mPOS Thermal Printer

Rev. 1.04

http://www.bixolon.com

Rev. 1.04

- 2 -

BGT-100P/102P

■ Safety Precautions

In using the present appliance, please keep the following safety regulations in order to

prevent a ny hazard or material damage.

WARNING

Violating following instructions can cause serious injury or death.

Do not bend the cable by force or leave it under any

heavy object.

• A damaged cable can cause a fire.

Do not plug in or unplug with your hands wet.

• You can be electrocuted.

Keep the plastic bag out of children’s reach.

• If not, a child may put the bag on his head.

Do not pull the cable to unplug.

• This can damage the cable, which is the origin of a fire or a

breakdown of the printer.

You must use only the supplied adapter.

• It is dangerous to use other adapters.

Do not plug several products in one multi-outlet.

• This can provoke over-heating and a fire.

• If the plug is wet or dirty, dry or wipe it before usage.

• If the plug does not fit perfectly with the outlet, do not plug in.

• Be sure to use only standardized multi-outlets.

PROHIBITED

ONLY SUPPLIED ADAPTER

PROHIBITED

Rev. 1.04

- 3 -

BGT-100P/102P

CAUTION

Violating following instructions can cause slight wound or damage the appliance.

Do not use the printer when it is out of order. This

can cause a fire or an electrocution.

• Switch off and unplug the printer before calling your dealer.

Do not let water or other foreign objects in the

printer.

• If this happened, switch off and unplug the printer before

calling your dealer.

Use only approved accessories and do not try to

disassemble, repair or remodel it for yourself.

• Call your dealer when you need these services.

• Do not touch the blade of auto cutter.

Install the printer on the stable surface.

• If the printer falls down, it can be broken and you can hurt

yourself.

Keep the desiccant out of children’s reach.

• If not, they may eat it.

If you observe a strange smoke, odor or noise from

the printer, unplug it before taking following

measures.

• Switch off the printer and unplug the set from the mains.

• After the disappearance of the smoke, call your dealer to

repair it.

TO UNPLUG

PROHIBITED

DISASSEMBLING

PROHIBITED

TO UNPLUG

PRINTER

DEALER

PRINTER

Rev. 1.04

- 4 -

BGT-100P/102P

■ Warning - U.S.A

i) Class A Digital Device : Wired Device

This equipment has been tested and found to comply with the limits for a Class A digital

device pursuant to Part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference when the equipment is operated in a

commercial environment. This equipment generates uses, and can radiate radio frequency

energy and, if not installed and used in accordance with the instruction manual, may cause

harmful interference to radio communications. Operation of this equipment in a residential

area is likely to cause harmful interference in which case the user will be required to

correct the interference at his own expense.

ii) Class B Digital Device : Wireless Device

This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation This

equipment generates, uses and can radiate radio frequency energy and, if not installed

and used in accordance with the instructions, may cause harmful interference to radio

communications, However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and on, the

user is encouraged to try to correct the interference by one or more of the following

measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver

is connected.

- Consult the dealer or an experienced radio/TV technician for help.

iii) Changes or modifications not expressly approved by the manufacturer

could void the user's authority to operate the equipment.

iv) Caution: Exposure to Radio Frequency Radiation.

To comply with FCC RF exposure compliance requirements, a separation

distance of at least 20 cm must be maintained between the antenna of this

device and all persons.

■ Notice - Canada

i) Class A Digital Device : Wired Device

This Apparatus complies with class “A” limits for radio interference as specified in the

Canadian department of communications radio interference regulations.

Get appareil est conforme aux normes class “A” d’interference radio tel que specifier par

ministre canadien des communications dans les reglements d’interference radio .

ii) Class B Digital Device : Wireless Device

This Apparatus complies with class “B” limits for radio interference as specified in the

Canadian department of communications radio interference regulations.

Get appareil est conforme aux normes class “B” d’interference radio tel que specifier par

ministre canadien des communications dans les reglements d’interference radio .

Rev. 1.04

- 5 -

BGT-100P/102P

■ Caution

Some semiconductor devices are easily damaged by static electricity. You should turn the

printer “OFF”, before you connect or remove the cables on the rear side, in order to guard

the printer against the static electricity. If the printer is damaged by the static electricity,

you should turn the printer “OFF”.

■ Waste Electrical and Electric Equipment (WEEE)

This marking shown on the product or its literature, indicates that is should not

be disposed with other household wastes at the end of its working life, To

prevent possible harm to the environment or human health from uncontrolled

waste disposal, please separate this from other types of wastes and recycle it

responsibly to promote the sustainable reuse of material resources. Household

users should contact either the retailer where they purchased this product, or

their local government office, for details of where and how they can take this item for

environmentally safe recycling. Business users should contact their supplier and check the

terms and conditions of the purchase contract. This product should not be mixed with other

commercial wastes for disposal.

■ Rating Label Symbol Information

DC (Direct current)

■ Notice

This device complies with Part 15 of the FCC Rules. Operation is subject to the following

two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference that may

cause undesired operation.

This device does not support Adaptivity of the CE Rules.

■ Label Material

* Control Label: PC

* Other Labels: PET

Rev. 1.04

- 6 -

BGT-100P/102P

■ Introduction to Product

BGT-100P/102P have been designed to be connected to various types of electronic

devices such as ECR (Electronic Cash Register), POS (Point Of Sales), and computer

peripheral devices.

Major features of the printer are as follows.

1. Print at a max. speed of 300mm/s(180 dpi)

2. Low noise thermal printing

3. Support of USB, Ethernet, Bluetooth, WLAN(Dongle Type)

4. Built-in data buffer (data can be received and buffered while printing)

5. Control of external devices like cash registers through peripheral device drive circuit

6. Barcode

7. Support of various print density settings (by changing DIP switch settings)

It is advisable to read the contents of this manual carefully before using the printer for the

first time.

※ Use only authorized supplies that can be trusted!

- We are not responsible for quality and service for damage caused by the use of

unauthorized products (or recycled ones).

- The following Bluetooth mark and QD ID B021701 is only applicable to models with the

Bluetooth SIG qualification.

We at Bixolon Co., Ltd. constantly strive to improve product functions and quality. To do

this, the specifications of our product and the contents of the manual may change without

prior notice.

Rev. 1.04

- 7 -

BGT-100P/102P

■ Table of Contents

1. Installing Printer and Getting Started ......................................................................... 8

1-1 Unpacking .............................................................................................................. 8

1-2 Interface ................................................................................................................. 9

1-2-1 USB Interface(Host Function USB A type connector) ................................... 9

1-2-2 USB Interface(Device Function USB B type connector) ............................. 10

1-2-3 Ethernet and Bluetooth Interface ................................................................ 10

1-3 Drawer Cable ....................................................................................................... 11

1-4 Setting Dip Switches ............................................................................................ 12

1-5 Installing & Replacing Paper ................................................................................ 13

1-6 Recommended Papers ........................................................................................ 15

1-7 Structure of 2 inches specification. ...................................................................... 15

1-8 Removing Paper Jam .......................................................................................... 16

1-9 Using Printer Functions ....................................................................................... 17

1-10 Connecting a Computer ..................................................................................... 17

1-11 Connecting Power Supply .................................................................................. 18

2. Self-Test ...................................................................................................................... 19

3. Hexadecimal Dumping .............................................................................................. 21

4. Specifications............................................................................................................. 22

5. Appendix ..................................................................................................................... 23

5-1 Cleaning Printer ................................................................................................... 23

Rev. 1.04

- 8 -

BGT-100P/102P

1. Installing Printer and Getting Started

1-1 Unpacking

Check the following contents list and contact your dealer for assistance if any item is

missing or incorrect.

BGT-100P/102P Cable Cover

Paper Installation Guide AC/DC Adapter Power Cord

Rev. 1.04

- 9 -

BGT-100P/102P

1-2 Interface

Connect the printer to the host computer using the right interface cable that complies with

the specifications of the interface. The drawer to be used with the printer should meet the

specifications of the printer.

※ CAUTIONS

Before connecting any cables, make sure that both the printer and the host are

turned off.

1-2-1 USB Interface(Host Function USB A type connector)

USB Interface can connect to the peripheral devices.

(ie. the barcode reader, customer display and WLAN Dongle that is supported by the

printer.)

Pint No.

Signal Name

Designation (Color)

Function

Shell

Shield

Drain Cable

Frame Ground

1

VBUS

RED

Host Power (+5VDC)

2

D-

WHITE

Data Line (D-)

3

D+

GREEN

Data Line (D+)

4

GND

BLACK

Signal Ground

* Do not connect the USB A-A type cable with the Printer and HOST(ex. PC)

* ② USB A-type connector and “HOST (PC)” USB B-type connector cannot be used at

the same time. Make sure you use only one of them

* ② USB A type connector can support the charging function and normal USB

communication function.

(When using Highspeed Charging function, please set to ON DIP switch pin 5.

Normal USB communication is not supported in Highspeed Charging)

USB A Connector(Host Function)

②

①

Rev. 1.04

- 10 -

BGT-100P/102P

1-2-2 USB Interface(Device Function USB B type connector)

USB Interface can connect to the Host System

Pint No.

Signal Name

Designation (Color)

Function

Shell

Shield

Drain Cable

Frame Ground

1

VBUS

RED

Host Power

2

D-

WHITE

Data Line (D-)

3

D+

GREEN

Data Line (D+)

4

GND

BLACK

Signal Ground

1-2-3 Ethernet and Bluetooth Interface

Use the function key, you can check Ethernet, wireless LAN, Bluetooth information.

For more information, please refer to the network documentation in Bixolon homepage.

1) Ethernet Interface

Pint No.

Signal Name

Color

Function

1

TD+

WHITE ORANGE

Transmit +

2

TD-

ORANGE

Transmit -

3

RD+

WHITE GREEN

Receive +

4

NC

BLUE

Reserved

5

NC

WHITE BLUE

Reserved

6

RD-

GREEN

Receive -

7

NC

WHITE BROWN

Reserved

8

NC

BROWN

Reserved

USB B Connector(Device Function)

Ethernet Connector

Function Key

Rev. 1.04

- 11 -

BGT-100P/102P

2) Bluetooth Interface

Bluetooth Communication Specifications

Item

Specifications

Frequency

2.402 ~ 2.480 GHz

Version

2.1 + EDR

Module Type

Class 1

* Bluetooth Connection

Printer can be connected to terminal devices with Bluetooth communication capability

(PDA, PC, smartphone, tablet PC, etc.)

* Refer to the Bluetooth Connection Manual for more detailed instructions about how to

establish the connection.

1-3 Drawer Cable

Connect the cash drawer connecting cable to the cash drawer connector located in the

back of the printer.

※ WARNING

Use a cash drawer that meets the printer specifications.

Using an improper cash drawer may cause faults in the cash drawer and the printer.

※ CAUTIONS

Do not connect a telephone line to the drawer kick-out connector.

Otherwise, the telephone line and the computer may be damaged.

Pin No.

Signal Name

Direction

1

Frame Ground

-

2

Drawer Kick-out Drive Signal 1

Output

3

Drawer Open/Close Signal

Input

4

+24VDC

-

5

Drawer Kick-out Drive Signal 2

Output

6

Signal Ground

-

Rev. 1.04

- 12 -

BGT-100P/102P

1-4 Setting Dip Switches

Switch (SW1)

Function

ON

OFF

Default

1-1

None

OFF

1-2

None

OFF

1-3

Print Density

Refer to the following table

*1)

OFF

1-4

OFF

1-5

Charging Mode

Highspeed

Charging

Normal

Charging

OFF

1-6

None

OFF

1-7

Emergency Download

Deactivated

Activated

ON

1-8

None

OFF

*1) Print Density(DIP Switch)

*2)

Print Density

1-3

1-4

Default

Level 1 (Low)

OFF

Level 1

Level 2

OFF

ON

Level 3

ON

OFF

Level 4 (High)

ON

※ Print density can be adjusted to 16 levels using the virtual memory switch.

Changing print density will affect the printing speed. Please refer to the following table

for details.

*2) Print Density(Virtual Memory Switch)

Speed

Print Density

(DIP Switch)

Low High

4 (High)

1

2

3

4

*)

Level 1

3

5

6

7

8

*)

Level 2

2

9

10

11

12

*)

Level 3

1 (Low)

12

13

14

16

*)

Level 4

The items indicated with "*" refers to the density when DIP Switch is set.

※ It is recommended to select Unified Utility or Self-Test mode to change print density

using the virtual memory switch.

※ Attention

The printer must be turned off when changing the DIP switch settings. Failure to turn it

off may cause a short circuit and damage the printer.

To change the settings:

1) Turn off the printer.

2) Open the DIP switch cover located at the back of the printer.

3) Set the DIP switch number.

4) Close the DIP switch cover after the settings have been completed.

5) Position the printer in front and turn it on.

※ Note

Please make sure that the printer is turned off when changing the DIP switch settings.

The change is not accepted when the power is on.

Rev. 1.04

- 13 -

BGT-100P/102P

1-5 Installing & Replacing Paper

※ CAUTIONS

Only use paper that meets the specifications otherwise the printer cannot recognize that

paper is not loaded.

1-5-1 Make sure that the printer is not receiving data; otherwise, data may be lost.

1-5-2 Open the paper roll cover by pressing the Cover-Open button.

※ CAUTIONS

Do not open the print cover while the printer is operating, otherwise the printer may be

damaged.

1-5-3 Remove any existing used paper roll core when replacing the paper roll

1-5-4 Insert the paper roll as shown in the following picture.

Rev. 1.04

- 14 -

BGT-100P/102P

1-5-5 Check the orientation of the roll paper when inserting it into the printer.

1-5-6 Pull out a small amount of paper as shown in the picture, and close the cover.

※ CAUTIONS

When closing the cover, hold down the center of printer cover firmly so that paper roll is

loaded correctly.

1-5-7 Cut the paper as shown in the following picture.

Rev. 1.04

- 15 -

BGT-100P/102P

1-6 Recommended Papers

- TF50KS-E (Paper Thickness: 65μm): Nippon Paper Industries Co., Ltd.

- PD 150R (Paper Thickness: 75μm): New Oji Paper Mfg. Co., Ltd.

- PD 160R (Paper Thickness: 75μm): New Oji Paper Mfg. Co., Ltd.

- P350 (Paper Thickness: 62μm): Kansaki Specialty Paper, Inc. (USA)

- P220AG (Paper Thickness: 65μm): Mitsubishi Paper Mills Limited

- P220A (Paper Thickness: 65μm): Mitsubishi Paper Mills Limited

- F5041 (Paper Thickness: 65μm): Mitsubishi HitecPaper Flensburg Gmbh

- P5047 (Paper Thickness: 60μm): Mitsubishi Paper Mills Limited

※ CAUTIONS

Use of papers other than those recommended above may damage TPH or degrade the

printing quality and our company is not responsible for the damage caused by non-

recommended papers. If you have to use other products, we recommend that you use

papers with a similar level of quality to the recommended ones.

1-7 Structure of 2 inches specification.

※ NOTE

This setting can be changed from VMSM Utility.

※ CAUTIONS

The changes for 2 inches specification should be applied to the following components as

well.

Screw

2 inches partition

2 inches roller

Rev. 1.04

- 16 -

BGT-100P/102P

1-8 Removing Paper Jam

1-8-1 When a paper jam occurs, turn the printer OFF and then back ON, open the cover,

and remove the jammed paper.

※ In case of a minor jam, it may be possible that the operating blade returns to the

original position and cover can be opened simply by turning the printer OFF and

then back ON.

Follow the steps shown below if the cover does not open after power cycling.

1-8-2 Turn the printer OFF.

1-8-3 Separate the cover-cutter while pressing down both sides as shown in the following

picture.

1-8-4 Turn the knob and insert the blade that sticks out using a cross-head screwdriver as

shown below.

1-8-5 Press the Cover-Open button, open the cover, remove the jammed paper, and

assemble the separated COVER-CUTTER.

1-8-6 Turn the printer ON and use it.

Rev. 1.04

- 17 -

BGT-100P/102P

1-9 Using Printer Functions

Control Panel

1-10 Connecting a Computer

Use the cable that comes with the printer to connect the printer to computers.

1-10-1 Plug the cable connector securely into the printer’s interface connector located in

the back of the printer.

○ POWER

Green light will be on when the power is supplied to printer after 10

seconds.

○ ERROR

Red light will be on in various error conditions (e.g. no paper, cover

open, etc.)

○ PAPER

Red LED will be lit when the paper roll is running low. The LED keeps

blinking when the printer is in self-test standby mode or macro execution

standby mode.

○ FEED

Press the FEED button once to feed out extra paper. Hold down

the FEED button to feed the paper continuously until the button is

released...

※ NOTE

When the printer is powered on, the Error indicator blinks in conjunction

with the Paper indicator during the initialization process.

Rev. 1.04

- 18 -

BGT-100P/102P

1-11 Connecting Power Supply

※ CAUTIONS

When connecting or disconnecting the power supply to and from the printer, make sure

that the power supply adapter is unplugged from the electrical outlet. Otherwise you may

damage the power supply or the printer.

If the power supply’s rated voltage and your outlet’s voltage do not match, do not plug in

the power cord and contact your dealer for assistance. Otherwise, you may damage the

power supply or the printer.

1-11-1 Make sure that the printer’s power switch is turned off, and the power supply’s

power cord is unplugged from the electrical outlet.

1-11-2 Check the label on the power supply to make sure that the voltage required by the

power supply matches that of your electrical outlet.

1-11-3 Plug in the power supply’s cable as shown below. Notice that the flat side of the

plug faces down.

※ NOTE

If you want to remove the power cord, grab the arrow part of the connector securely and

pull it straight out.

Rev. 1.04

- 19 -

BGT-100P/102P

2. Self-Test

The self-test checks whether the printer has any problems. If the printer does not function

properly, contact your dealer. The self-test procedure is as follows:

2-1 Make sure paper roll has been installed properly.

2-2 Turn on the power while holding down the FEED button and the self-test begins.

2-3 The self-test prints the current status of the printer including control ROM version and

the DIP switch settings.

2-4 After printing the current printer status, the printer wait for the next step after printing

the following lines. (The paper signal light keeps blinking.)

SELF-TEST PRINTING.

PLEASE PRESS THE FEED BUTTON.

Continuous SELF-TEST : Less than 1 second

VMSM Selection : 1 second or more

2-5 Press the FEED button to resume printing or hold down the FEED button for 1 second

to set the virtual switch.

2-5-1 Self-Test

2-5-1-1 If you press the FEED button for less than 1 second, the printer will print in the

preset character type.

2-5-1-2 The self-test completes automatically and cuts the paper after printing the following

line.

*** COMPLETED ***

2-5-1-3 The printer goes into standby mode when the self-test is complete.

Rev. 1.04

- 20 -

BGT-100P/102P

2-5-2 Virtual Switch Setting Mode

2-5-2-1 When the printer goes into virtual switch-setting mode, the following lines will be

printed:

** VMSM Selection **

0: Exit and reboot printer

1: Print current settings

2: Set Print Density

3: Set Print Speed

4: Set Cutting mode

5: Set External Buzzer after cutting

6: Set Internal Buzzer after cutting

7 or more: None

2-5-2-2 Make sure to press the FEED button to perform the above functions.

2-5-2-2-1 Step 1: Press the button to make a selection.

2-5-2-2-2 Step 2: Hold down the button for at least 1 second to apply the selection.

If no selection is made in Step 1, the mode setting will be canceled.

2-5-3 After making changes, make sure to hold down the FEED button for at least 1

second to save the changes. The paper will be cut after printing the following line:

(“0: Exit and reboot printer” must be executed to save the settings on the printer.)

*** COMPLETED ***

2-6 The settings will take effect after the printer reboots.

La page charge ...

BIXOLON BGT-100Pt Manuel utilisateur

Ce manuel convient également à

BIXOLON BGT-100Pt Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents