Sears Canada 110C96562500 Le manuel du propriétaire

Marque: Sears Canada

Modèle: 110C96562500

Taper: Le manuel du propriétaire

Gas Dryer

S_cheuse & gaz

Models/Modeles 110.C9656", C9657"

* = color number/numero de couleur

iiiiii!Jiiiiiiiiiii!il

8576585 Sears Canada Inc., Toronto, Ontario, Canada M5B 2B8 www.sears.ca

TABLEOF CONTENTS

WARRANTY ..................................................................................... 2

PEDESTAL OPTION WARRANTY ................................................. 2

DRYER SAFETY .............................................................................. 3

INSTALLATION INSTRUCTIONS .................................................. 4

Tools and Parts ............................................................................ 4

Optional Pedestal ......................................................................... 5

Location Requirements ............................................................... 5

Electrical Requirements ................................................................ 7

Gas Supply Requirements ........................................................... 7

Venting Requirements .................................................................. 8

Plan Vent System ...................................................................... 10

Install Vent System .................................................................... 11

Install Leveling Legs .................................................................. 11

Make Gas Connection ............................................................... 12

Connect Vent ............................................................................. 12

Level Dryer ................................................................................. 12

Reverse Door Swing .................................................................. 13

Complete Installation ................................................................. 14

DRYER USE ................................................................................. 15

Starting Your Dryer .................................................................... 15

Stopping or Restarting Your Dryer ............................................ 16

Lock Controls ............................................................................ 16

Loading Guide ........................................................................... 16

Drying and Cycle Tips ............................................................... 16

Status Lights .............................................................................. 17

Cycles ........................................................................................ 17

Modifiers .................................................................................... 18

Options ...................................................................................... 18

Changing Cycles, Options and Modifiers ................................. 19

TUMBLE FREETM Non-Heated Dryer Rack ............................... 19

DRYER CARE .............................................................................. 20

Cleaning the Dryer Location ...................................................... 20

Cleaning the Lint Screen ........................................................... 20

Cleaning the Dryer Interior ......................................................... 20

Removing Accumulated Lint ..................................................... 20

Vacation and Moving Care ........................................................ 21

TROUBLESHOOTING .................................................................. 21

MAINTENANCE AGREEMENTS ................................................. 22

SERVICE NUMBERS ............................................... BACK COVER

WARRANTY

One Year Full Warranty on Kenmore HE2 Dryer

For one year from the date of purchase, when installed and

operated according to the Use & Care Guide, this dryer will be

repaired (or replaced if repair proves impossible) free of charge if

defective in material or workmanship.

Warranty Restriction

• Ifthis dryer is used for other than private family purposes, this

warranty applies for only 90 days from the date of purchase.

• Exhausting this dryer with a plastic or metal foil vent will void

this warranty.

Warranty Service

Warranty service is available by calling 1-800-4-MY-HOME ® This

warranty applies only while this dryer is used in the United States

or Canada. This warranty gives you specific legal rights, and you

may also have other rights which vary from state to state.

Sears, Roebuck and Co.

Dept. 817WA, Hoffman Estates, IL 60179

Product Record

In the space following, record your complete model number,

serial number, and purchase date. You can find this information

on the model and serial number label, located at the top inside

dryer door well.

Have this information available to help you quickly obtain

assistance or service when you contact Sears concerning your

appliance.

Model number110.

Serial number

Purchase date

Save these instructions and your sales receipt for future

reference.

PEDESTAL OPTION WARRANTY

One Year Full Warranty on Pedestal

For one year from the date of purchase, when installed according

to its Installation Instructions, this pedestal will be repaired or

replaced free of charge if it is defective in material or

workmanship.

Warranty Restriction

This warranty is void if this pedestal is used for other than private

family purposes, or used with any other product than those listed

in its Installation Instructions.

Warranty Service

Warranty service is available by calling 1-800-4-MY-HOME ®.This

warranty applies only while this pedestal is used in the United

States or Canada. This warranty gives you specific legal rights,

and you may also have other rights which vary from state to

state.

In the space following, record your complete model number,

serial number, and purchase date. You can find this information

on the model and serial number label.

Have this information available to help you quickly obtain

assistance or service when you contact Sears concerning your

appliance.

Model number110.

Serial number

Purchase date

Save these instructions and your sales receipt for future

reference.

DRYER SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be killed or seriously injured if you don't immediately

follow instructions.

You can be killed or seriously injured if you don't follow

instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

WARNING: For your safety, the information in this manual must be followed to minimize

the risk of fire or explosion, or to prevent property damage, personal injury, or death.

- Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this

or any other appliance.

- WHAT TO DO IF YOU SMELL GAS:

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use any phone in your building.

• Clear the room, building, or area of all occupants.

• Immediately call your gas supplier from a neighbor's phone. Follow the gas supplier's

instructions.

• If you cannot reach your gas supplier, call the fire department.

- Installation and service must be performed by a qualified installer, service agency, or

the gas supplier.

iMPORTANT SAFETY iNSTRUCTiONS

WARNING: To reduce the risk of fire, electric shock, or injury to persons when using the dryer, fellow basic precautions,

including the following:

m Read N!l instructions before using the dryer.

m Do not place items exposed to cooking oils in your dryer.

items contaminated with cooking oils may contribute to

a chemical reaction that could cause a load to catch fire.

m Do not dry articles that have been previously cleaned in,

washed in, soaked in, or spotted with gasoline, dry-

cleaning solvents, or other flammable or explosive

substances as they give off vapors that could ignite or

explode.

m Do not allow children to play on or in the dryer. Close

supervision of children is necessary when the dryer is

used near children.

m Before the dryer is removed from service or discarded,

remove the door to the drying compartment.

m Do not reach into the dryer if the drum is moving.

m Do not install or store the dryer where it will be exposed

to the weather.

m Do not tamper with controls.

m Do not repair or replace any part of the dryer or attempt

any servicing unless specifically recommended in this

Use and Care Guide or in published user-repair

instructions that you understand and have the skills to

carry out.

• Do not use fabric softeners or products to eliminate static

unless recommended by the manufacturer of the fabric

softener or product.

• Do not use heat to dry articles containing foam rubber or

similarly textured rubber-Hike materials.

• Clean lint screen before or after each load.

• Keep area around the exhaust opening and adjacent

surrounding areas free from the accumulation of lint, dust,

and dirt.

• The interior of the dryer and exhaust vent should be

cleaned periodically by qualified service personnel.

• See installation instructions for grounding requirements.

SAVE THESE iNSTRUCTiONS

IMPORTANT: The gas installation must conform with local codes, or in the absence of local codes, with the Canadian Natural Gas

and Propane Installation Code, CSA B149.1.

The dryer must be electrically grounded in accordance with local codes, or in the absence of local codes, with the Canadian

Electrical Code, CSA C22.1.

INSTALLATIONINSTRUCTIONS

Gather the required tools and parts before starting installation.

Read and follow the instructions provided with any tools listed

here.

8" or 10" pipe wrench

8" or 10" adjustable

wrench (for gas

connections)

Flat-blade screwdriver

Adjustable wrench that

opens to 1" (2.54 cm) or

hex-head socket wrench

(for adjusting dryer feet)

v4" nut driver or socket

wrench (recommended)

• Level

• Vent clamps

• Knife

• Pipe-joint compound

resistant to LP gas

• Caulking gun and

compound (for installing

new exhaust vent)

• Pliers

• Tape measure

Parts supplied

Remove parts package from dryer drum. Check that all parts

were included.

4 Leveling legs

NOTE: Do not use leveling legs if installing the dryer on a

pedestal.

Parts needed

Check local codes and with gas supplier. Check existing gas

supply, electrical supply and venting. Read "Electrical

Requirements," "Gas Supply Requirements" and "Venting

Requirements" before purchasing parts.

• For close-clearance installations between 28.65" (72.77 cm)

and 34.15" (86.74 cm), see "Plan Vent System" section for

venting requirements.

I-*- 34.1s"--_1

(86.74 cm)

Mobile home installations require special parts (listed following)

available for purchase from your local Sears store or Sears

Service Center. For further information, please call

1-800-4-MY-HOME ®(1-800-469-4663).

• Mobile Home Installation Kit. Ask for Part Number 346764.

• Metal exhaust system hardware.

Areyouplacingthedryeronapedestal?Youcanpurchasea

pedestalseparatelyforthisdryer.Thispedestalwilladdabout

10"(25.4cm)totheheightofyourunitforatotalheightof

approximately46"(116.8cm).

Foragarageinstallation,youwillneedtoplacethedryeratleast

18"(46cm)abovethefloor.

Optional pedestal

The pedestal is available in:

White - Part Number 46822

To order, call your local Sears store. For further information,

please call 1-80O-4-MY-HOME ®(1-800-469-4663).

Stack Kit

Are you planning to stack your Kenmore washer and dryer? To do

so, find the stack kit in the dryer drum. Follow instructions

included with the kit. See "Location Requirements."

Explosion Hazard

Keep flammable materials and vapors, such as

gasoline, away from dryer.

P_ace dryer at _east 18 inches (48 cm) above the floor

for a garage installation.

Failure to do so can result in death, explosion, or fire.

You will need

• A location that allows for proper exhaust installation. A gas

dryer must be exhausted to the outdoors. See "Venting

Requirements."

• A grounded electrical outlet located within 2 ft (61 cm) of

either side of the dryer. See "Electrical Requirements."

• A sturdy floor to support the total dryer weight of

127 Ibs (57.6 kg). The combined weight of a companion

appliance and pedestals should also be considered.

A level floor with a maximum slope of 1" (2.5 cm) under entire

dryer. (If slope is greater than 1" [2.5 cm], install Extended

Dryer Feet Kit, Part Number 279810.) Clothes may not tumble

properly and automatic sensor cycles may not operate

correctly if dryer is not level.

Do not operate your dryer at temperatures below 45°F (7°C). At

lower temperatures, the dryer might not shut off at the end of an

automatic cycle. Drying times can be extended.

The dryer must not be installed or stored in an area where it will

be exposed to water and/or weather.

Check code requirements. Some codes limit, or do not permit,

installation of the dryer in garages, closets, mobile homes, or

sleeping quarters. Contact your local building inspector.

NOTE: No other fuel-burning appliance can be installed in the

same closet as a dryer.

Installation clearances

Thelocation must be large enough to allow the dryer door to

open fully.

Dryer Dimensions

(91=4 cm)

*Most installations require a minimum 5" (12,7 cm) clearance

behind the dryer for the exhaust vent with elbow. See "Venting

Requirements."

Installation spacing for recessed area or closet installation

The following spacing dimensions are recommended for this

dryer. This dryer has been tested for spacing of 0" (0 cm)

clearance on the sides and rear. Recommended spacing should

be considered for the following reasons:

• Additional spacing should be considered for ease of

installation and servicing.

• Additional clearances might be required for wall, door and

floor moldings.

• Additional spacing should be considered on all sides of the

dryer to reduce noise transfer.

For closet installation, with a door, minimum ventilation

openings in the top and bottom of the door are required.

Louvered doors with equivalent ventilation openings are

acceptable.

• Companion appliance spacing should also be considered.

Custom undercounter installation - Dryer only

.... 2"*

1'_ I_ _-(scm)

36" rnin O

1"* _ "_r"'--27"----_-- 1"*

(2 5 cm) (68 6 crn) (2 5 crn)

*Required spacing

Closet installation - Dryer only

II ]lllU/ll t I 24in.__

L_I(1550m2,

I1"*_ 28.65"_-I5"*'1

(2.5cm} (7227 cm) (12.7 cm)

8"*

(7.8ore)

A. Side view - closet or confined area

B. Closet door with vents

*Required spacing

**For side or bottom venting, 0" (0 cm) spacing is allowed.

Recessed or closet installation - Dryer on pedestal

1"-_11_-27"-_] I_-1''

(2.5cm)

_1t Hq1,fro*

. = ",

I1"14 28.65"_-I5....

(68.6cm} (2.5cm} {2.5cm) {72.77cm){12.7cm)

A B

A. Recessed area

B. Side view - closet or confined area

*Required spacing

**For side or bottom venting, 0" (0 cm) spacing is allowed.

Minimum installation spacing for cabinet installation

• The dimensions shown are for the recommended spacing.

• For cabinet installation, with a door, minimum ventilation

openings in the top of the cabinet are required.

(22 9cm}

5"* 28.65" 1" 1" 27" 1"

(12.7 crn) (72.77 cm) (2.5 cm) (2.5 cm)(68.6 cm) (2.5 crn)

*Required spacing

**For side or bottom venting, 0" (0 cm) spacing is allowed.

Recommended installation spacing for recessed or

closet installation, with stacked washer and dryer

The dimensions shown are for the recommended spacing..

481_? *

(81(}cm_}

24 im2*

(155¢m_)

*Required spacing

5"* _

(12.7¢m)

3"* (7.6 cm)

3"* {7.6cm) __

_ -,,,,{-1"*{2.5cm)

5"*(15.2cm)

/2;::::

:_/

72"

(182.9cm)

x2 -//

{2.5Bin) {68.6cm} '

{2.5Bin}

*Required spacing

Mobile home - additional installation requirements

This dryer is suitable for mobile home installations. The

installation must conform to the Canadian Manufactured Home

Standard, CAN/CSA-Z240 MH.

Mobile home installations require:

• Metal exhaust system hardware, which is available for

purchase from your local Sears store or Sears Service Center.

• Mobile Home Installation Kit Part Number 346764. See "Tools

and Parts" section for ordering information.

Special provisions must be made in mobile homes to

introduce outside air into the dryer. The opening (such as a

nearby window) should be at least twice as large as the dryer

exhaust opening.

Electdca} Shock Hazard

Pmuginto a grounded 3 prong outlet.

Do not remove ground prong,

Do not use an adapter,

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electricam shock,

120 Volt, 60 Hz., AC only, 15- or 20-amp fused electrical

supply is required. A time-delay fuse or circuit breaker is

recommended. It is also recommended that a separate circuit

serving only this dryer be provided.

GROUNDING INSTRUCTIONS

m For a grounded, cord-connected dryer:

This dryer must be grounded. In the event of malfunction or

breakdown, grounding will reduce the risk of electric shock

by providing a path of least resistance for electric current.

This dryer is equipped with a cord having an equipment-

grounding conductor and a grounding plug. The plug must

be plugged into an appropriate outlet that is properly

installed and grounded in accordance with all local codes

and ordinances.

WARNING: Improper connection of the equipment-

grounding conductor can result in a risk of electric shock.

Check with a qualified electrician or service representative

or personnel if you are in doubt as to whether the dryer is

properly grounded. Do not modify the plug provided with the

dryer: if it will not fit the outlet, have a proper outlet installed

by a qualified electrician.

SAVE THESE INSTRUCTIONS

Expmosion Hazard

Use a new CSA International approved gas suppmy mine.

Install a shut-off vamve,

Securely tighten aimgas connections.

ff connected to LP, have a quamified person make sure

gas pressure does not exceed 13" (33 cm) water

column,

Examples of a qualified person include:

licensed heating personne{,

authorized gas company personnem, and

authorized service personnel

Failure to do so can resumt in death, expmosion, or fire.

Gas Type

Natural gas:

This dryer is equipped for use with Natural gas. It is design-

certified by CSA International for LP (propane or butane) gases

with appropriate conversion.

• Your dryer must have the correct burner for the type of gas in

your home. Burner information is located on the rating plate

in the door well of your dryer. If this information does not

agree with the type of gas available, contact your local Sears

store or Sears Service Center.

LP gas conversion:

Conversion must be made by a qualified technician.

No attempt shall be made to convert the appliance from the gas

specified on the model/serial rating plate for use with a different

gas without consulting your gas company.

Gas supply line

• 1/2"IPS pipe is recommended.

• %" approved tubing is acceptable for lengths under 20 ft

(6.1 m) if local codes and gas supplier permit.

• Must include W' NPT minimum plugged tapping accessible

for test gauge connection, immediately upstream of the gas

connection to the dryer (see illustration).

iiii..................................

• Must include a shutoff valve:

An individual shutoff valve must be installed within 6 feet

(1.8 m) of the dryer in accordance with the National Fuel Gas

Code, ANSI Z223.1. The location should be easy to reach for

opening and closing.

A C E

B D

A. %" flexible gas connector

B. _" pipe to flare adapterfitting

C. _" NPT rninirnurn plugged tapping

D. Y;" NPT gas supply line

E. Gas shutoff valve

Gas supply connection requirements

• For close clearances, a %" to %" elbow is recommended to

prevent kinking of the gas line.

• Use only pipe-joint compound. Do not use TEFLON _t tape.

There are many methods by which your gas dryer can be

connected to the gas supply. Listed here are some guidelines for

two different methods of connection.

Option 1 (Recommended method)

Flexible stainless steel gas connector:

• Iflocal codes permit, use a new flexible stainless steel gas

connector (Design Certified by CSA International) to connect

your dryer to the rigid gas supply line. Use an elbow and a %"

flare x %" NPT adapter fitting between the stainless steel gas

connector and the dryer gas pipe, as needed to prevent

kinking.

Option 2 (Alternate method)

Approved aluminum or copper tubing:

• Lengths under 20 ft (6.1 m) can use %" approved tubing (if

codes and gas supplier permit).

• Ifyou are using Natural gas, do not use copper tubing.

• %" flare x %" NPT adapter fitting between dryer pipe and

%" approved tubing.

• Lengths over 20 ft (6.1 m) should use larger tubing and a

different size adapter fitting.

• Ifyour dryer has been converted to use LP gas, %" LP

compatible copper tubing can be used. If the total length of

the supply line is more than 20 ft (6.1 m), use larger tubing.

NOTE: Pipe-joint compounds that resist the action of LP gas

must be used. Do not use TEFLON _ttape.

Burner input requirements

Elevations up to 10,000 ft (3,048 m):

• The design of this dryer is certified by CSA International for

use at altitudes up to 10,000 ff (3,048 m) above sea level at

the Btu rating indicated on the model/serial number plate.

Burner input adjustments are not required when the dryer is

operated up to this elevation.

Elevations above 10,000 ft (3,048 m):

• When installed above 10,000 ft (3,048 m) a 4% reduction of

the burner Btu rating shown on the model/serial number plate

is required for each 1,000 ft (305 m) increase in elevation.

Gas supply pressure testing

• The dryer must be disconnected from the gas supply piping

system during pressure testing at pressures greater than

1/2psi.

Dryer gas pipe

• The gas pipe that comes out through the rear of your dryer

has a %" male pipe thread.

A. F2"NPT gas supply line

B. _" NPT dryer pipe

*NOTE: If the dryer is mounted on a pedestal, the gas pipe height

must be an additional 10" (25.4 cm) from the floor. For a garage

installation, the gas pipe height must be an additional

18" (46 cm) from the floor.

Fire Hazard

Use a heavy metal vent.

Do not use a p_aetic vent.

Do not use a meta_ foil vent.

Failure to follow these instructions can result in death

or fire.

WARNING: To reduce the risk of fire, this dryer MUST BE

EXHAUSTED OUTDOORS.

IMPORTANT: Observe all governing codes and ordinances.

The dryer exhaust must not be connected into any gas vent,

chimney, wail, ceiling or a concealed space of a building.

If using an existing vent system

• Clean lint from the entire length of the system and make sure

exhaust hood is not plugged with lint.

• Replace any plastic or metal foil vent with rigid or flexible

heavy metal vent.

• Review Vent system chart. Modify existing vent system if

necessary to achieve the best drying performance.

t®TEFLON is a registered trademark of E.I. Du Pont De Nemours and Company.

If this is a new vent system

Vent material

• Use a heavy metal vent. Do not use plastic or metal foil vent.

• 4" (10.2 cm) heavy metal exhaust vent and clamps must be

used, DURASAFE TMventing products are recommended,

4" (10.2cm) heavy metal exhaust vent

DURASAFE TMvent products can be purchased from your

dealer. For further information, please call

1-800-4-MY-HOME ®(1-800-469-4663) or visit our website at

www.sears.ca.

Rigid metal vent

• For best drying performance, rigid metal vents are

recommended.

• Rigid metal vent is recommended to avoid crushing and

kinking.

Flexible metal vent

• Flexible metal vents are acceptable only if accessible for

cleaning.

• Flexible metal vent must be fully extended and supported

when the dryer is in its final location.

• Remove excess flexible metal vent to avoid sagging and

kinking that may result in reduced airflow and poor

performance.

• Do not install flexible metal vent in enclosed walls, ceilings or

floors.

Elbows

45° elbows provide better airflow than 90° elbows.

Good Bet_r

Clamps

• Use clamps to seal all joints.

• Exhaust vent must not be connected or secured with screws

or other fastening devices that extend into the interior of the

duct. Do not use duct tape.

_IOC

Clamp

Exhaust

Recommended hood styles are shown here.

(10_2 cm)

A. Louvered hood style

B.Box heod style

The angled hood style (shown here) is acceptable.

(10.2 cm__

An exhaust hood should cap the vent to keep rodents and

insects from entering the home.

Exhaust hood must be at least 12" (30.5 cm) from the ground

or any object that may be in the path of the exhaust (such as

flowers, rocks or bushes, snow line, etc.).

Do not use an exhaust hood with a magnetic latch.

improper venting can cause moisture and lint to collect

indoors, which may result in:

[] Moisture damage to woodwork, furniture, paint,

wallpaper, carpets, etc.

[] Housecleaning problems and health problems=

Choose your exhaust installation type

Recommended exhaust installations

Typical installations vent the dryer from the rear of the dryer.

Other installations are possible.

A. Dryer

B. Elbow

C. Wall

D. Exhaust hood

E. Clamps

F. Rigid metal or flexible metal vent

G. Vent length necessary to connect elbows

H. Exhaust outlet

Optional exhaust installations

Fire Hazard

Cover unused exhaust homes with the following kit:

279818 (white)

Contact your toccatadeamer.

Faimureto follow these instructions can result in death,

fire, emectricamshock, or serious injury.

This dryer can be converted to exhaust out the right side, left

side, or through the bottom. Contact your local dealer to have the

dryer converted.

A B

A. Standard rear offset exhaust installation

B. Left or right side exhaust installation

C. Bottom exhaust installation (not an option

with pedestal installations)

Alternate installations for close clearances

Venting systems come in many varieties. Select the type best for

your installation. Two close-clearance installations are shown.

Refer to the manufacturer's instructions.

/_ / i l/

\r " i

A B

A. Over-the-top installation (also available with one

offset elbow)

B. Periscope installation

NOTE: The following kits for close clearance alternate

installations are available for purchase. For further information,

please call 1-800-4-MY-HOME ®(1-800-469-4663).

• Over-the-Top Installation:

Part Number 26-49900

• Periscope Installation (For use with dryer vent to wall vent

mismatch):

Part Number 26-49901 - Less than 5" (12.7 cm) mismatch

Part Number 26-49908 - 5" (12.7 cm) to 18" (45.72 cm)

mismatch

Part Number 26-49904 - 18" (45.72 cm) to 29" (73.66 cm)

mismatch

Part Number 26-49905 - 29" (73.66 cm) to 50" (127 cm)

mismatch

Special provisions for mobile home installations

The exhaust vent must be securely fastened to a noncombustible

portion of the mobile home structure and must not terminate

beneath the mobile home. Terminate the exhaust vent outside.

i]i

Determine vent path

• Select the route that will provide the straightest and most

direct path outdoors.

• Plan the installation to use the fewest number of elbows and

turns.

• When using elbows or making turns, allow as much room as

possible.

• Bend vent gradually to avoid kinking.

• Use the fewest 90 ° turns possible.

Determine vent length and elbows needed for best

drying performance

• Use the following Vent system chart to determine type of vent

material and hood combinations acceptable to use.

• NOTE: Do not use vent runs longer than those specified in

the Vent system chart. Exhaust systems longer than those

specified will:

• Shorten the life of the dryer.

• Reduce performance, resulting in longer drying times and

increased energy usage.

The Vent system chart provides venting requirements that will

help to achieve the best drying performance.

Vent system chart

NOTE: Side and bottom exhaust installations have a 90° turn

inside the dryer. To determine maximum exhaust length, add one

90° turn to the chart.

Number of Type of Box or Angled

90° turns vent Iouvered hoods

or elbows hoods

0 Rigid metal 64 ft (20 m) 58 ft (17.7 m)

Flexible metal 36 ft (11 m) 28 ft (8.5 m)

1 Rigid metal 54 ft (16.5 m) 48 ft (14.6 m)

Flexible metal 31 ft (9.4 m) 23 ft (7 m)

2 Rigid metal 44 ft (13.4 m) 38 ft (11.6 m)

Flexible metal 27 ft (8.2 m) 19 ft (5.8 m)

3 Rigid metal 35 ft (10,7 m) 29 ft (8.8 m)

Flexible metal 25 ft (7.6 m) 17 ft (5.2 m)

4 Rigid metal 27 ft (8.2 m) 21 ft (6.4 m)

Flexible metal 23 ft (7 m) 15 ft (4.6 m)

1. Install exhaust hood. Use caulking compound to seal exterior

wall opening around exhaust hood.

2. Connect vent to exhaust hood. Vent must fit inside exhaust

hood. Secure vent to exhaust hood with 4" (10.2 cm) clamp.

3. Run vent to dryer location. Use the straightest path possible.

See "Determine vent path" in "Plan Vent System." Avoid 90°

turns. Use clamps to seal all joints. Do not use duct tape,

screws or other fastening devices that extend into the interior

of the vent to secure vent.

1. To protect the floor, use a large flat piece of cardboard from

the dryer carton. Place cardboard under the entire back edge

of the dryer.

2. Firmly grasp the body of the dryer. Gently lay the dryer on the

cardboard. See Illustration.

i \\\

i \\

i \\\\\\

3. Examine the leveling legs. Find the diamond marking.

4. Screw the legs into the leg holes by hand. Use a wrench to

finish turning the legs until the diamond marking is no longer

visible.

5. Place a carton corner post from dryer packaging under each

of the 2 dryer back corners. Stand the dryer up. Slide the

dryer on the corner posts until it is close to its final location.

Leave enough room to connect the exhaust vent or gas line.

For mobile home use

Gas dryers must be securely fastened to the floor at the time of

installation.

Mobile home installations require a Mobile Home Installation Kit.

For more information, please call 1-800-4-MY-HOME ®

(1-800-469-4663).

Remove the red cap from the gas pipe.

Using a wrench to tighten, connect the gas supply to the

dryer. Use pipe-joint compound on the threads of all non-

flared male fittings. If flexible metal tubing is used, be sure

there are no kinks.

A .....................................

A. Flared male fitting

B. Non-flared male fitting

NOTE: For LP gas connections, you must use pipe-joint

compound resistant to the action of LP gas. Do not use

TEFLON _ttape.

A combination of pipe fittings must be used to connect the

dryer to the existing gas line. Shown is a recommended

connection. Your connection may be different, according to

the supply line type, size and location.

A. _" flexible gas connector

B. _" dryer pipe

C. _" to _" pipe elbow

D. _" pipe-to-flare adapter fitting

3. Open the shutoff valve in the supply line. The valve is open

when the handle is parallel to the gas pipe.

A. Closed valve

B. Open valve

Test all connections by brushing on an approved

noncorrosive leak-detection solution. Bubbles will show a

leak. Correct any leak found.

1. Using a 4" (10.2 cm) clamp, connect vent to exhaust outlet in

dryer. If connecting to existing vent, make sure the vent is

clean. The dryer vent must fit over the dryer exhaust outlet

and inside the exhaust hood. Make sure the vent is secured

to exhaust hood with a 4" (10.2 cm) clamp.

2. Move dryer into its final location. Do not crush or kink vent.

3. (On gas models) Make sure that there are no kinks in the

flexible gas line.

4. Once the exhaust vent connection is made, remove the

corner posts and cardboard.

Check the levelness of the dryer. Check levelness first

side to side, then front to back.

If the dryer is not level, prop up the dryer using a wood block.

Use a wrench to adjust the legs up or down and check again for

levelness.

t®TEFLON is a registered trademark of E.I. Du Pont De Nemours and Company.

i!::::_;il)_!il)_@ii'_%;!i!_[30oi" ii!i!_wii[_!!]iiiill

You can change your door swing from a right-side opening to a

left-side opening, if desired.

1. Place a towel or soft cloth on top of the dryer or work space

to protect the surface.

Remove the door assembly

1. Remove the 4 screws that hold the door hinge on the front

panel of the dryer.

A. Dryer front panel

B. Door assembly

Lay the door assembly on a flat, protected surface with the

inside (inner door assembly) facing up.

Remove the 6 Phillips head screws to release the outer door

assembly from the inner door assembly, as indicated below.

See illustration. It is important that you remove only the

6 indicated screws.

Reverse hinge

1. Use a small flat-blade screwdriver to remove 2 plug strips

from the inner door. Slide the head of the screwdriver under

the plugs, being certain not to scratch the inner door surface.

Lift up.

Remove the 4 screws that attach to the inner door hinge and

move the hinge to the other side. Reinstall the 4 screws.

A. Door hinge

3. Reinstall plug strips on opposite side of the inner door.

4. Check for fingerprints on the glass. Clean glass if necessary.

5. Place the inner door assembly inside the outer door

assembly. To fit correctly, the inner door assembly edge fits

completely inside the outer door assembly edge.

6. Reassemble the inner and outer door assemblies with the

6 screws.

4. Lift the inner door assembly off the outer door assembly.

5. Rotate outer door 180 °.

180"

Reverse the strike

1. Use a small flat-blade screwdriver to remove plug strip from

the dryer door opening. Slide the head of the screwdriver

under the plugs, being certain not to scratch the dryer

surface. Lift up.

2. Remove the strike

3. Insert strike and plug strip on the opposite side.

1. Check that all parts are now installed. If there is an extra part,

go back through the steps to see which step was skipped.

2. Check that you have all of your tools.

3. Dispose of/recycle all packaging materials.

4. Check the dryer's final location. Be sure the vent is not

crushed or kinked.

5. Check that the dryer is level. See "Level Dryer."

A.Plug strip (cannot be seenfrom this angle)

B. Door strike

Reinstall the door

1. Reattach door to dryer front panel with the 4 screws.

EmectricaI Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

FaiJure to follow these instructions can result in death,

fire, or emectrica{ shock.

A. Dryer front panel

B. Door assembly

2. Check for fingerprints on the glass. Clean glass if necessary.

3. Close door and check that it latches securely.

6. Plug into a grounded 3 prong outlet. Turn on power.

7. Remove any protective film or tape remaining on the dryer.

8. Read "Dryer Use."

9. Wipe the dryer drum interior thoroughly with a damp cloth to

remove any dust.

10. Select a Timed Dry heated cycle, and start the dryer. Do not

select the Air Only modifier.

If the dryer will not start, check the following:

• Dryer is plugged into a grounded 3 prong outlet.

• Electrical supply is connected.

• Household fuse is intact and tight, or circuit breaker has

not tripped.

• Dryer door is closed.

11. When the dryer has been running for 5 minutes, open the

dryer door and feel for heat. Ifyou feel heat, cancel cycle and

close door. If you do not feel heat, turn off the dryer and

check that the gas supply line shutoff valve is open.

• Ifthe gas supply line shutoff valve is closed, open it, then

repeat the 5-minute test as outlined above.

• Ifthe gas supply line shutoff valve is open, contact a

qualified technician.

DRYER USE

MODIFIERS & OPTIONS

STATUS

Power

Wet

Cool Down (_

Clothes Dry _ _More

Wrinkle Guard 0 _ Normal

O Less

Controls Locked a

Check Lint Screen v'

Dryness

Level

AUTO CYCLESONE'

AUTO

CYCLES Delicate

Casual

Normal

Jeans

I igh

Medium High

Medium

Low

Extra Low

_!_Air Only

Temperature

Expmosion Hazard

Keep flammable materials and vapors, such as

gasoline, away from dryer.

Do net dry anything that has ever had anything

flammable on it (even after washing).

FaiBure to follow these instructions can result in death,

explosion, or fire.

Fire Hazard

No washer can completely remove oH.

Do not dry anything that has ever had any type of oil on

it (including cooking oils).

Items containing foam, rubber, or pmaetic must be dried

on a clothesline or by using an Air Cycme.

Failure to follow these instructions can result in death

or fire.

Follow these basic steps to start your dryer. Please refer to

specific sections of this manual for more detailed information.

f. Clean lint screen before each load. See "Cleaning the Lint

Screen."

2. Place laundry into dryer and shut door. See "Loading Guide."

3. Press POWER.

Select an Auto or Timed Cycle. The preset settings for Auto

or Timed Cycles will illuminate. The estimated (auto cycle) or

actual (timed) cycle time (in minutes) will show in the display.

NOTE: A default time is displayed when an automatic cycle is

selected. During the first few minutes of the drying process,

the cycle time may automatically vary from the default time

based on the size and fabric type of the load. Toward the end

of the drying process, the estimated time display will adjust

again, showing the final drying time.

To use an Auto Cycle

• Select an Auto Cycle. Auto cycles are preset to Normal.

• Select DRYNESS LEVEL to adjust how dry you want the

load. As the cycle runs, the control senses the dryness of

the load and adjusts the time automatically for the

selected dryness level.

To make changes to the Dryness Level and/or Options

during an Auto Cycle:

• Press STOP once.

Adjust Dryness Level and/or Options.

NOTE: Dryness Level selections can be made only while

using Auto Cycles. Selecting More, Normal or Less

automatically adjusts the sensed time needed

Normal

Less

Dryness

Level

AUTO CYCLES ONLY

Auto Dry cycles take the guesswork out of drying time

and enhances fabric care. The amount of time that is

displayed is the estimated time remaining in the cycle.

To use a Timed Cycle

Select a Timed Cycle.

Press MORE TIME or LESS TIME until the desired drying

time is displayed. Tap MORE TIME or LESS TIME and the

time will change by 1-minute intervals. Press and hold

MORE TIME or LESS TIME, and the time will change by

5-minute intervals.

NOTE: The Timed Cycle Adjust feature can be used only

with Timed Cycles.

• Press TEMPERATURE until the desired temperature

illuminates.

To make changes to Time and/or Options during a Timed

Cycle:

• Press STOP once.

• Adjust the Time and/or Options.

5. (OPTIONAL STEP) Ifdesired, select WRINKLE GUARD ®. For

more details, see "WRINKLE GUARD°. ''

6. (OPTIONAL STEP) The Cycle Signal is preset to on. If desired,

you may turn the Cycle Signal off.

7. Press and hold START for approximately 1 second until dryer

starts. Be sure the door is closed.

• Ifyou do not press Start within 5 minutes of selecting a

cycle, the dryer automatically shuts off.

To pause/stop the dryer at any time

Open the door or press STOP once.

To restart the dryer

Close the door. Press and hold START until dryer starts.

To end/cancel your dryer at any time

Press STOP twice or open the door.

NOTE: Drying will continue from where the cycle was interrupted

if you close the door and press Start within 5 minutes. If the cycle

is interrupted for more than 5 minutes, the dryer will shut off.

Select new cycle settings before restarting the dryer.

This feature allows you to lock your settings to prevent

unintended use of the dryer. You can also use the control lock

feature to prevent unintended cycle or option changes during

dryer operation.

To enable the control lock feature:

Press and hold CYCLE SIGNAL button for 3 seconds. The

CONTROLS LOCKED icon lights up, and a single beep tone is

heard. To unlock, press and hold CYCLE SIGNAL button for

3 seconds. The indicator light turns off.

Properly loading your dryer can lower your utility bill and prolong

the life of your garments.

Loading suggestions

• Load the dryer by the amount of space items take up, not by

their weight.

• Do not overload the dryer. This causes uneven drying and

wrinkling

Super Capacity Dryers

(sample loads)

Sturdy Work Clothes

4 jeans 2 sweatpants

4 workpants 2 sweatshirts

4 workshirts

Towels

10 bath towels

10 hand towels

14 washcloths

Mixed Load

3 sheets (1 king, 2 twin) 9 T-shirts

4 pillowcases 9 shorts

3 shirts 10 handkerchiefs

3 blouses

Select the correct cycle and dryness level or temperature for your

load. If an Auto Cycle is running, the display shows the estimated

cycle time, which is determined by your dryer automatically

sensing the dryness level of your load. If a Timed Cycle is

running, the display shows the exact number of minutes

remaining in the cycle.

Cool Down tumbles the load without heat during the last few

minutes of all cycles. Cool Down makes the loads easier to

handle and reduces wrinkling. The length of the Cool Down

depends on the load size and dryness level.

Drying tips

• Follow care label directions when they are available.

• If desired, add a fabric softener sheet. Follow package

instructions.

• To reduce wrinkling, remove the load from the dryer as soon

as tumbling stops. This is especially important for permanent

press, knits and synthetic fabrics.

• Avoid drying heavy work clothes together with lighter fabrics.

This could cause overdrying of lighter fabrics and lead to

increased shrinkage or wrinkling.

Cycle tips

• Dry most loads using the preset cycle settings.

• Refer to the Auto Cycles or Timed Cycles Preset Settings

chart (in the "Cycles" section) for a guide to drying various

loads.

Drying temperature and Dryness Level are preset when

you choose an Auto Cycle. You can select a different

dryness level, depending on your load, by pressing

Dryness Level and choosing More or Less.

NOTE: You cannot use the Timed Cycle Adjust and you

cannot modify temperature with the Auto Dry cycles.

Ifyou wish to adjust the cycle length of a Timed Cycle,

press More Time or Less Time. Adjust the temperature of

a Timed Cycle by pressing TEMPERATURE until the

desired temperature is selected.

NOTE: You cannot use the Dryness Level with Timed

Cycles.

Follow the progress of your dryer with the drying Status indicator

lights.

STATUS

Damp

CoolDown

ClothesDry

Wrinkle GuardO

Select the drying cycle that matches the type of load you are

drying. See the Auto Cycles Preset Settings chart or the Timed

Cycles Preset Settings chart.

AUTO

CYCLES Delica_

TIMED

Casual CYCLES

Timed

Normal ..........

Dry

Jeans Express

Dry

HeavyDuty TouchUp

ControlsLocked

CheekUntScreen V

Wet

The Wet light illuminates at the beginning of an Auto Cycle if a

wet item is detected.

• In an Auto Cycle, if a wet item is not detected after

approximately 5 minutes, the dryer goes directly into Cool

Down and the Cool Down and WRINKLE GUARD®indicators

illuminate, if selected.

• In a Timed Cycle, wet items are not detected. The dryer will

continue to run for the length of time selected, and the Wet

light will illuminate. The damp light will not illuminate.

Damp

The Damp light illuminates in an Auto Cycle when the laundry is

approximately 80% dry.

Cool Down

The Cool Down light illuminates during the cool down part of the

cycle. Laundry cools for ease in handling.

Clothes Dry

The Clothes Dry light illuminates when the drying cycle is

finished. This indicator stays on during WRINKLE GUARD_L

WRIN KLE GUARD _

The WRINKLE GUARD _light illuminates when this option is

selected. This indicator stays on with Clothes Dry.

Check Lint Screen

The Check Lint Screen light is a reminder to check to see

whether the lint screen needs to be cleaned. The Check Lint

Screen light will come on when the machine is turned on. The

light will flash until the cycle is started or the door is opened.

Indicator lights

Other indicator lights show Cycle, Options and Modifier settings

selected.

Auto Cycles allow you to match the cycle to the load you are

drying. See the following Auto Cycles Preset Settings chart. Each

cycle dries certain fabrics at the recommended temperature. A

sensor detects the moisture in the load and automatically adjusts

the drying time for optimal drying.

Heavy Duty

Use this cycle to get high heat for heavy fabrics such as cotton

towels or bedspreads.

Jeans

Use this cycle to get medium-high heat for drying denims.

Normal

Use this cycle to get medium heat for drying sturdy fabrics such

as sturdy work clothes.

Casual

Usethis cycleto g_low he_ fordrying no-ironfabrics, such as

sport shirts, casualbusinessclothesand permanentpress

blends.

Delicate

Use this cycle to get extra low heat for drying synthetic fabrics,

washable knit fabrics and no-iron finishes

Auto Cycles Preset Settings

Auto Cycles Load Type Temperature Time*

(Minutes)

HEAVY DUTY High 45

Heavyweight, towels

JEANS Medium High 55

Denim pants, jackets

NORMAL Medium 40

Corduroys, sturdy work

clothes

CASUAL Low 35

Permanent press,

synthetics, casual

business clothes

DELICATE Extra Low 30

Sheets, lingerie, blouses

*Estimated Time with Dryness Level (Normal) setting. Time will

vary depending on load type and load size.

Use Timed Cycles to select a specific amount of drying time and

a drying temperature. When a Timed Cycle is selected, the

Estimated Time Remaining display shows the actual time

remaining in your cycle. You can change the actual time in the

cycle by pressing More Time or Less Time. See "Changing

Cycles, Options and Modifiers."

Timed Dry

Use this cycle to complete drying if items are still damp after an

Auto Cycle. Timed Dry is also useful for drying heavyweight and

bulky items, such as bedspreads and work clothes.

EXPRESS DRY TM

Use this cycle for drying small loads or loads that need a short

drying time.

Touch Up

Use this cycle to help smooth out wrinkles from items such as

clothes packed in a suitcase or items wrinkled from being left in

the dryer too long.

Timed Cycles Preset Settings

Timed Cycles Load Type Temperature Default Time

(Minutes)

TIMED DRY High 40

Heavyweight, bulky items,

bedspreads, work clothes

EXPRESS DRY TM High 23

Small loads, sturdy fabric

TOUCH UP Medium High 20

Helps to smooth out

wrinkles

Use Modifiers to select temperatures for the Timed Cycles only.

Press Temp Adjust until the desired temperature setting glows.

Temperature modifiers cannot be used with the Auto Cycles.

! High

i Medium High

Medium

_Low

Extra Low

Air0nly

Temperature

A[);_}S IlM[D _Y/'LES

ONlY

Air Only

Use the Air Only Modifier for items that require drying without

heat such as rubber, plastic and heat-sensitive fabrics. This table

shows examples of items that can be dried using Air Only.

Type of Load Time*

(Minutes)

Foam rubber - pillows, padded bras, stuffed toys 20 - 30

Plastic - Shower curtains, tablecloths 20 - 30

Rubber-backed rugs 40 - 50

Olefin, polypropylene, sheer nylon 10 - 20

*Reset cycle to complete drying, if needed.

When using Air Only

• Check to see that coverings are securely stitched.

• Shake and fluff pillows by hand periodically during the cycle.

• Dry item completely. Foam rubber pillows are slow to dry.

NOTE: Air Only is not available with Auto Cycles.

You can customize your cycles by selecting options.

O Wrinkle Guard

Cycle Signal

LOCK] UNLOCKCONTROLS

WRINKLE GUARD _

WRINKLE GUARD ®helps smooth out wrinkles that form when

you cannot unload the dryer promptly at the end of a cycle.

During this option, the dryer stops tumbling and then tumbles

again for a brief period.

• Press WRINKLE GUARD ®to get up to 90 minutes of heat-

free, periodic tumbling at the end of a cycle.

• Stop WRINKLE GUARD ®at any time by pressing WRINKLE

GUARD _ or opening the dryer door.

• WRINKLE GUARD _is preset to OFE The Auto Dry cycles will

retain the WRINKLE GUARD ®setting. For example, if you

select WRINKLE GUARD ®in the Normal cycle, WRINKLE

GUARD _ will be on the next time you select the Normal cycle.

NOTE: WRINKLE GUARD ®must be selected with a cycle in order

to work. If you do not select WRINKLE GUARD ®, the dryer stops

after cool down.

Cycle Signal

The Cycle Signal produces an audible sound when the drying

cycle is finished. Promptly removing clothes at the end of the

cycle reduces wrinkling.

Press CYCLE SIGNAL to turn the signal off.

NOTE: When WRINKLE GUARD ®is selected and the Cycle

Signal is on, a tone sounds every 5 minutes until the clothes are

removed, or WRINKLE GUARD _ ends.

You can change Auto Cycles, Timed Cycles, Modifiers and

Options anytime before pressing Start.

• Three short tones sound if an unavailable combination is

selected. The last selection will not be accepted.

Changing Cycles after pressing Start

1. Press STOP twice. This ends the current cycle.

2. Select the desired cycle and options.

3. Press and hold START.The dryer starts at the beginning of

the new cycle.

NOTE: If you do not press Start within 5 minutes of selecting the

cycle, the dryer automatically shuts off.

Changing Modifiers and Options after pressing Start

You can change a Modifier or Option anytime before the selected

Modifier or Option begins.

1. Press STOP once.

2. Select the new Modifier and/or Option.

3. Press and hold START to continue the cycle.

NOTE: If you happen to press Stop twice, the program clears and

your dryer shuts down. Restart the selection process.

The dryer rack is shipped in place in your dryer. Remove and

discard any packing material before use.

Use the TUMBLE FREETM Non-Heated Dryer Rack for items that

you do not want to tumble dry, such as sweaters.

To use the dryer rack

Do not remove the lint screen.

1. Open dryer door.

A. Front edge

2. Place dryer rack inside dryer drum, positioning the back wire

on the ledge of the inner dryer back panel. Push down on

front edge of dryer rack to secure over the lint screen.

A.Dryerrack front edge

B.Dryerback panel

3. Put the wet items on top of the rack. Leave space between

the items so air can reach all the surfaces.

NOTE: Do not allow items to hang over the edge of the rack.

4. Close the door.

5. Press the POWER button.

6. Select a timed cycle and temperature (see following chart).

Items containing foam, rubber, or plastic must be dried on a

clothesline or by using the Air Only temperature setting.

7. You may change the cycle time by pressing MORE TIME or

LESS TIME. Reset time as needed to complete drying. Refer

to the following table.

8. Press (and hold) START button (about 3 seconds).

NOTE: You must remove rack for normal tumbling. Do not use

automatic cycles with the dryer rack.

This chart shows examples of items that can be rack dried and

the suggested temperature setting and drying time. Actual drying

time will depend on the amount of moisture items hold.

Rack Dry Setting Temp. Time*

Wool Sweaters Timed Low 60

Block to shape and lay flat on Cycles

the rack.

Stuffed toys or pillows Timed Low 60

Cotton or polyester fiber filled cycles

Stuffed toys or pillows Timed Air Only 90

Foam rubber filled cycles (no heat)

Sneakers or canvas shoes Timed Air Only 90

cycles (no heat)

*(Minutes) Reset time to complete drying, if needed.

DRYER CARE

Keep dryer area clear and free from items that would obstruct the

flow of combustion and ventilation air.

Explosion Hazard

Keep flammable materials and vapors, such as

gasoline, away from dryer,

Place dryer at least 18 inches (46 cm) above the floor

for a garage installation.

Faimureto do so can result in death, explosion, or fire.

Every load cleaning

The lint screen is located in the door opening of the dryer. The

control panel has an indicator light to remind you to clean the lint

screen before each load. A screen blocked by lint can increase

drying time.

To clean

1. Pull the lint screen straight up. Roll lint off the screen with

your fingers. Do not rinse or wash screen to remove lint. Wet

lint is hard to remove.

2. Push the lint screen firmly back into place.

IMPORTANT:

• Do not run the dryer with the lint screen loose, damaged,

blocked, or missing. Doing so can cause overheating and

damage to both the dryer and fabrics.

Some towels made of synthetic fibers and natural fibers

(polyester and cotton blends) may shed more lint than other

towels, causing your dryer's lint screen to fill up faster. Be

sure to remove lint from the lint screen before and after drying

new towels.

• If lint falls off the screen into the dryer during removal, check

the exhaust hood and remove the lint. See "Venting

Requirements."

As needed cleaning

Laundry detergent and fabric softener residue can build up on the

lint screen. This buildup can cause longer drying times for your

clothes, or cause the dryer to stop before your load is completely

dry. The screen is probably clogged if lint falls off the screen.

Clean the lint screen with a nylon brush every 6 months, or more

frequently, if it becomes clogged due to a residue buildup.

To wash

1. Roll lint off the screen with your fingers.

2. Wet both sides of lint screen with hot water.

3. Wet a nylon brush with hot water and liquid detergent. Scrub

lint screen with the brush to remove residue buildup.

4. Rinse screen with hot water.

5. Thoroughly dry lint screen with a clean towel. Replace screen

in dryer.

To clean dryer drum

1. Make a paste with powdered laundry detergent and very

warm water.

2. Apply paste to a soft cloth.

Apply a liquid, nonflammable household cleaner to the

stained area and rub with a soft cloth until all excess dye and

stains are removed.

3. Wipe drum thoroughly with a damp cloth.

4. Tumble a load of clean cloths or towels to dry drum.

NOTE: Garments that contain unstable dyes, such as denim blue

jeans or brightly colored cotton items, may discolor the dryer

interior. These stains are not harmful to your dryer and will not

stain future loads of clothes. Dry unstable dye items inside out to

avoid dye transfer.

From Inside the Dryer Cabinet

Lint should be removed every 2 years or more often, depending

on dryer usage. Cleaning should be done by a qualified person.

From the Exhaust Vent

Lint should be removed every 2 years, or more often, depending

on dryer usage.

La page charge ...

Sears Canada 110C96562500 Le manuel du propriétaire

Marque: Sears Canada

Modèle: 110C96562500

Taper: Le manuel du propriétaire

Télécharger le PDF

rapport

dans d''autres langues

English: Sears Canada 110C96562500 Owner's manual

Documents connexes

Kenmore 110C87562601 Le manuel du propriétaire

Sears Canada 110C96562500 Le manuel du propriétaire

Sears Canada 110C96562500 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents