Omega OM-CP-RFC1000 Le manuel du propriétaire
- Taper
- Le manuel du propriétaire
OM-CP-RFC1000-EXT
Wireless Transciever
MQS5066/1216
Xxxxx Xxxxxx
Xxxxx Xxxxxx Xxxxxxxx
M0000/0016
INSTRUCTION
SHEET
Shop online at omega.com
SM
e-mail: [email protected]
For latest product manuals: www.omegamanual.info
Xxxxx Xxxxxx
Xxxxx Xxxxxx Xxxxxxxx
M0000/0016
INSTRUCTION
SHEET
Shop online at omega.com
SM
e-mail: [email protected]
For latest product manuals: www.omegamanual.info
Product Notes
The OM-CP-RFC1000-EXT is a high powered transciever designed to provide network connectivity
between wireless data loggers and the base station computer. This design includes an external antenna,
allowing flexibility with mounting positions in both orientation and proximity to metal walls.
The OM-CP-RFC1000-EXT may be used as a repeated or plugged directly into the PC.
Transmission Distance
The OM-CP-RFC1000-EXT transmits to other OM-CP-RFC1000-EXTs up to 4000 feet maximum typi-
cal outdoors/line of sight, 1000 feet maximum typical indoors/urban. The OM-CP-RFC1000-EXTs
transmits to data loggers up to 2000 feet maximum typical outdoors/line of sight, 500 feet maximum
typical indoors/urban. The OM-CP-RFC1000-EXT can connect to a maximum of 64 data loggers.
The OM-CP-RFC1000-EXT transmits on a frequency of 2.405GHz - 2.475 GHz.
Operating Environment
The OM-CP-RFC1000-EXT is rated for use in an environment with temperatures from -20°C to 85°C
and a humidity range of 0% to 95% RH non-condensing.The OM-CP-RFC1000-EXT is rated IP40 and is
protected against solids that are greater than 1mm in size. This device is not water resistant.
LEDs
The red LED indicates that the device has power. The green LED will blink when communicating with
other devices.
Installing the Software
Insert the Software Flash Drive into a USB port on the PC. If the autorun does not appear, locate the
drive on the computer and double click on Autorun.exe. Follow the prompts on the screen to install the
Omega Data Logger Software.
Channel Programming for the OM-CP-RFC1000-EXT
The OM-CP-RFC1000-EXT transmits data on the 2.5GHz band, channel 11. Each Wireless Data Logger
and OM-CP-RFC1000-EXT has a set of dip switches with which the channel may be programmed.
For proper communication, all data loggers or OM-CP-RFC1000-EXTs on the same network are required
to use the same channel. If they are not on the same channel, the devices will not communicate with
one another.
OM-CP-RFC1000-EXT: To program the channel on an RFC1000, first unplug the RFC1000-EXT. Use
a Phillips head screwdriver to unscrew the enclosure. The dip switches are located on the front of the
PCB circuit board. Change the dip switches to match the photo. Reconnect the RFC1000-EXT.
See examples on next page.
OM-CP-RFC1000-EXT
Channel 11 Channel 12 Channel 13 Channel 14
Channel 15 Channel 16 Channel 17 Channel 18
Channel 19 Channel 20 Channel 21 Channel 22
Channel 23 Channel 24 Channel 25 Channel 26
(not supported)
Deploying and Activating Devices
Step 1: Plug the OM-CP-RFC1000-EXT into the USB port on the base station computer.
(Additional OM-CP-RFC1000s can be used as repeaters to transmit over greater distances)
Step 2: If using multiple OM-CP-RFC1000-EXTs plug each one into a wall outlet in the desired locations.
(If transmitting over a distance greater than 1000 feet indoors or 4000 feet outdoors or there are walls/
obstacles/corners that need to be maneuvered around, set up additional OM-CP-RFC1000-EXTs as needed.)
If not using multiple OM-CP-RFC1000-EXTs, go to step 3.
Step 3: Verify that the data loggers are in wireless transmission mode by confirming the wireless ON /
OFF switch is in the ‘1’ position on each data logger. (See Channel Programming steps above)
Step 4: On the PC, launch the Omega Data Logging software. All active data loggers will be listed in the
software showing that the device(s) are recognized.
Step 5: To activate your data loggers, click on one to highlight, then right click to select the desired
Start method. Do this for each logger in your list that you wish to activate.
OM-CP-RFC1000-EXT
The default wireless channel for Omega
wireless devices is channel 11. Different
wireless channels may be used to create
multiple networks in one area, or to avoid
wireless interference from other devices.
The images below show the orientations
avaliable of the switches for each channel.
Channel 26 (all switches in the up position)
is not supported.
See examples to the left.
OM-CP-RFC1000-EXT
Mounting Instructions
For best wireless performance, both the OM-CP-RFC1000-EXT and the Omega data loggers should
be mounted in the same orientation. This usually means that the external antenna should be pointing
straight up. The antenna can pivot to accommodate either a wall mount or a desk mount.
Description OM-CP-RFC1000-EXT
Transmission Distance
(to other OM-CP-
RFC1000-EXTs)
4000’ max. outdoor - line of sight unobstructed
1000’ max. indoors - typical urban environment
Transmission Distance
(to Data Loggers)
2000’ max. outdoor - line of sight unobstructed
500’ max. indoors - typical urban
Maximum Connected
Data Loggers
64
LED Indicators Red & Green
Frequency 2.405GHz - 2.475GHz
Ingress Protection IP40
Interface Type USB (to PC) / Wirelesss (to Data Logger)
Operating Environment –20°C to +85°C (-4°F to 185°F),
0%RH to 95%RH (non-condensing)
Material ABS Plastic (body), PVC Plastic (antenna)
Dimensions Enclosure: 3.8” x 1.6” x 0.8” / Antenna: 7.2”
Approvals FCC ID:OA3MRF24J40MC, IC#: 7693A-24J40MC
“This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may
not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause
undesired operation.”
“To satisfy FCC RF Exposure requirements for mobile and base station transmission devices, a separation distance of 20 cm or
more should be maintained between the antenna of this device and persons during operation. To ensure compliance, operation
at closer than this distance is not recommended. The antenna(s) used for this transmitter must not be co-located or operating in
conjunction with any other antenna or transmitter.”
“This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:
(1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause
undesired operation of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation
est autorisée aux deux conditions suivantes: (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit
accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.”
“Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser)
gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and
its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful
communication.
Conformément à la réglementation d’Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d’un type et
d’un gain maximal (ou inférieur) approuvé pour l’émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage
radioélectrique à l’intention des autres utilisateurs, il faut choisir le type d’antenne et son gain de sorte que la puissance isotrope
rayonnée équivalente (p.i.r.e.) ne dépasse pas l’intensité nécessaire à l’établissement d’une communication satisfaisante.”
Compliance Information
OM-CP-RFC1000-EXT
OM-CP-RFC1000-EXT
Interface Type USB (to PC) / Wireless (to Data Logger)
Operating Environment -20 to +85°C, 0 to 100%RH non-condensing
LED Indicators
Red: Indicates that the device has power
Green: Will blink when communicating with the OM-CP-RFOT
Enclosure Materials Enclosure Body: Acetal Plastic, Cover: 300 Series Stainless Steel, Antenna Boot: Neoprene
Dimensions
Enclosure 3.4” x 2.9” x 1.3”
With antenna, normal to case: 3.4” x 2.9” x 8.8”
With antenna, laid down: 9.2” x 2.9” x 2.6”
Weight 14.1oz (400g)
Compatible Data Loggers OM-CP-RFOT, OM-CP-Therm-A-lert, OM-CP-RF2000A Series
Approvals FCC ID: OA3MRF24J40MC, IC#: 7693A-24J40MC, ETSI 300 328 (EU R&TTE)
Transmission Distance
(To other OM-CP-
RFC1000-IP69K’s)
4,000’ max. outdoors - line of sight unobstructed
1,000’ max. indoors - typical urban environment
Transmission Distance
(To data loggers)
2,000’ max. outdoors - line of sight unobstructed
500’ max. indoors - typical urban
Maximum number of
connected data loggers
64
Ingress Protection IP69K
Compliance Information
This device complies with Part 15 of the FCC Rules. Operatio n is subject to the following two conditions: (1) this device may not
cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired
operation.”
“To satisfy FCC RF Exposure requirements for mobile and base station transmission devices, a separation distance of 20cm or more
should be maintained between the antenna of this device and persons during operation. To ensure compliance, operation at closer than
this distance is not recommended. The antenna(s) used for this transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter.”
“This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:
(1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause
undesired operation of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est
autorisée aux deux conditions suivantes: (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter
tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.”
“Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser)
gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and
its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful
communication.
Conformément à la réglementation d’Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d’un type et
d’un gain maximal (ou inférieur) approuvé pour l’émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage
radioélectrique à l’intention des autres utilisateurs, il faut choisir le type d’antenne et son gain de sorte que la puissance isotrope
rayonnée équivalente (p.i.r.e.) ne dépasse pas l’intensité nécessaire à l’établissement d’une communication satisfaisante.”
Description
OM-CP-RFC1000-IP69K
Interface Type USB (to PC), Wireless (to Data Logger)
Operating Environment
OM-CP-RFC1000-CE: -20 °C to +85 °C (-4 °F to +185 °F), 0 %RH to 95 %RH
non-condensing
Power Supply: 0 °C to +40 °C (+32 °F to +104 °F), 20 %RH to 85 %RH non-condensing
LED Indicators
Power: Red
Data: Green
Enclosure Materials
Body: ABS Plastic
Antenna: PVC Plastic
Transmission Distance
to Data Logger
Unobstructed line-of-sight (outdoors): 2,000 feet max
Typical urban environment (indoors): 500 feet max
Transmission Distance
to RFC1000-CE
Unobstructed line-of-sight (outdoors): 2,500 feet max
Typical urban environment (indoors): 700 feet max
Compatible Data Loggers OM-CP-RFOT, Therm-A-lert and OM-CP-RF2000A Series
Maximum number of
connected data loggers
64
Frequency 2.405 GHz - 2.475 GHz
Ingress Protection IP40
Dimensions
Body: 3.8 in x 1.6 in x 0.8 in (96.52 mm x 40.64 mm x 20.32 mm)
Antenna: 2.7 in (69 mm)
Weight 1.4 oz (40 g)
Approvals
FCC ID: OA3MRF24J40MC, IC#: 7693A-24J40MC,
CE, ETSI 300 328 (EU R&TTE)
Description
OM-CP-RFC1000-EXT-EUR
OM-CP-RFC1000-EXT
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not
cause harmful interference, and (2) this device must accept any interference received, including interference that may cause
undesired operation.
To satisfy FCC RF Exposure requirements for mobile and base station transmission devices, a separation distance of 20 cm or
more should be maintained between the antenna of this device and persons during operation. To ensure compliance, operation
at closer than this distance is not recommended. The antenna(s) used for this transmitter must not be co-located or operating
in conjunction with any other antenna or transmitter.
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two
conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference
that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation
est autorisée aux deux conditions suivantes: (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit
accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.
Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or
lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna
type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary
for successful communication.
Conformément à la réglementation d’Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d’un
type et d’un gain maximal (ou inférieur) approuvé pour l’émetteur par Industrie Canada. Dans le but de réduire les risques
de brouillage radioélectrique à l’intention des autres utilisateurs, il faut choisir le type d’antenne et son gain de sorte que la
puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l’intensité nécessaire à l’établissement d’une communication
satisfaisante.
Compliance Information
WARRANTY/DISCLAIMER
OMEGA ENGINEERING, INC. warrants this unit to be free of defects in materials and workmanship for a period of 13 months
from date of purchase. OMEGA’s WARRANTY adds an additional one (1) month grace period to the normal one (1) year product
warranty to cover handling and shipping time. This ensures that OMEGA’s customers receive maximum coverage on each product.
If the unit malfunctions, it must be returned to the factory for evaluation. OMEGA’s Customer Service Department will issue an
Authorized Return (AR) number immediately upon phone or written request. Upon examination by OMEGA, if the unit is found
to be defective, it will be repaired or replaced at no charge. OMEGA’s WARRANTY does not apply to defects resulting from
any action of the purchaser, including but not limited to mishandling, improper interfacing, operation outside of design limits,
improper repair, or unauthorized modification. This WARRANTY is VOID if the unit shows evidence of having been tampered with
or shows evidence of having been damaged as a result of excessive corrosion; or current, heat, moisture or vibration; improper
specification; misapplication; misuse or other operating conditions outside of OMEGA’s control. Components in which wear is not
warranted, include but are not limited to contact points, fuses, and triacs.
OMEGA is pleased to offer suggestions on the use of its various products. However, OMEGA neither assumes
responsibility for any omissions or errors nor assumes liability for any damages that result from the use of its
products in accordance with information provided by OMEGA, either verbal or written. OMEGA warrants only
that the parts manufactured by the company will be as specified and free of defects. OMEGA MAKES NO OTHER
WARRANTIES OR REPRESENTATIONS OF ANY KIND WHATSOEVER, EXPRESSED OR IMPLIED, EXCEPT THAT OF
TITLE, AND ALL IMPLIED WARRANTIES INCLUDING ANY WARRANTY OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE ARE HEREBY DISCLAIMED. LIMITATION OF LIABILITY: The remedies of purchaser set forth
herein are exclusive, and the total liability of OMEGA with respect to this order, whether based on contract, warranty,
negligence, indemnification, strict liability or otherwise, shall not exceed the purchase price of the component upon
which liability is based. In no event shall OMEGA be liable for consequential, incidental or special damages.
CONDITIONS: Equipment sold by OMEGA is not intended to be used, nor shall it be used: (1) as a “Basic Component” under 10
CFR 21 (NRC), used in or with any nuclear installation or activity; or (2) in medical applications or used on humans. Should any
Product(s) be used in or with any nuclear installation or activity, medical application, used on humans, or misused in any way,
OMEGA assumes no responsibility as set forth in our basic WARRANTY / DISCLAIMER language, and, additionally, purchaser will
indemnify OMEGA and hold OMEGA harmless from any liability or damage whatsoever arising out of the use of the Product(s) in
such a manner.
FOR WARRANTY RETURNS, please have the following
information available BEFORE contacting OMEGA:
1. Purchase Order number under which the product was
PURCHASED,
2. Model and serial number of the product under warranty, and
3. Repair instructions and/or specific problems relative to the
product.
FOR NON-WARRANTY REPAIRS,
consult OMEGA for current
repair charges. Have the following information available BEFORE
contacting OMEGA:
1. Purchase Order number to cover the COST of the repair,
2. Model and serial number of the product, and
3. Repair instructions and/or specific problems relative to the
product.
OMEGA’s policy is to make running changes, not model changes, whenever an improvement is possible. This affords our customers the latest in technology and
engineering. OMEGA is a registered trademark of OMEGA ENGINEERING, INC.
© Copyright 2016 OMEGA ENGINEERING, INC. All rights reserved. This document may not be copied, photocopied, reproduced, translated, or reduced to any electronic
medium or machine-readable form, in whole or in part, without the prior written consent of OMEGA ENGINEERING, INC.
RETURN REQUESTS / INQUIRIES
Direct all warranty and repair requests/inquiries to the OMEGA Customer Service Department. BEFORE RETURNING ANY
PRODUCT(S) TO OMEGA, PURCHASER MUST OBTAIN AN AUTHORIZED RETURN (AR) NUMBER FROM OMEGA’S CUSTOMER
SERVICE DEPARTMENT (IN ORDER TO AVOID PROCESSING DELAYS). The assigned AR number should then be marked on the
outside of the return package and on any correspondence.
The purchaser is responsible for shipping charges, freight, insurance and proper packaging to prevent breakage in transit.
The information contained in this document is believed to be correct, but OMEGA accepts no liability for any errors it contains, and reserves the
right to alter specifications without notice.
Servicing North America:
U.S.A. Omega Engineering, Inc.
Headquarters: Toll-Free: 1-800-826-6342 (USA & Canada only)
Customer Service: 1-800-622-2378 (USA & Canada only)
Engineering Service: 1-800-872-9436 (USA & Canada only)
Tel: (203) 359-1660 Fax: (203) 359-7700
For Other Locations Visit omega.com/worldwide
omega.com [email protected]
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
Omega OM-CP-RFC1000 Le manuel du propriétaire
- Taper
- Le manuel du propriétaire
dans d''autres langues
- English: Omega OM-CP-RFC1000 Owner's manual
Documents connexes
-
Omega OM-CP-TEMP1000IS-A Le manuel du propriétaire
-
Omega OS212-MT Le manuel du propriétaire
-
-
-
-
-
