LG Electronics S3MFBN Le manuel du propriétaire

ENGLISH FRANÇAIS ESPAÑOL

MFL66101237

Rev.11_101320

Read this owner’s manual thoroughly before operating the

appliance and keep it handy for reference at all times.

OWNER’S MANUAL

STYLER

S3*F**

www.lg.com

2 TABLE OF CONTENTS

3 PRODUCT FEATURES

4 IMPORTANT SAFETY INSTRUCTIONS

4 Safety Instructions for Installation

5 Safety Instructions for Connecting Electricity

6 Basic Safety Precautions

7 Grounding Instructions

8 PRODUCT OVERVIEW

8 Parts

9 Accessories

10 The Moving Hanger

10 The Pants Crease Care

11 The Shelf

11 Choosing Styler Features

12 INSTALLATION

12 Installation Overview

12 ProductSpecications

13 Unpacking the Styler

13 Choosing the Proper Location

14 Installation Location Requirements

14 Clearances

16 Leveling the Styler

17 Reversing the Door

17 Installing on Carpeting

18 Installing the Anti-Tip Device

18 Assembling the Drip Tray

18 Installing Cap Covers

18 Installing Hinge Covers

19 OPERATION

19 Before Use

20 Using the Styler

21 Sorting Loads

Fabric Care Labels

Grouping Similar Items

Choosing Styler-Safe Clothing

22 Fabric Care Guide

24

Checking the Filters Before Every Load

Checking the Lint Filter

Changing the Aroma Sheet

25 Checking the Water Tanks

25 Loading the Styler

Hangers

Using the Moving Hanger

Pants Hanger or Pants Crease Care

Shelf

29 Control Panel

Control Panel Features

31 Cycle Guide

Cycle Processes

32 Choosing a Cycle

33 Cycle Settings and Options

34 EXTRA Functions

Locking the Controls

Setting a Delayed Start Time

Smart Diagnosis™

Night Care

36 SMART FUNCTIONS

36 LG ThinQ Application

39 Smart Diagnosis™ Function

40 MAINTENANCE

40 Regular Cleaning

Cleaning the Interior and Exterior

Cleaning the Lint Filter

Cleaning the Aroma Filter

Cleaning the Water Tanks

42 TROUBLESHOOTING

42 FAQs

43 Before Calling for Service

44 Error Codes

46 WARRANTY

TABLE OF CONTENTS

3PRODUCT FEATURES

ENGLISH

PRODUCT FEATURES

REMOVE ODORS

Use the Styler's Refresh cycle to quickly and easily remove odors from clothes.

REFRESH CLOTHING OR ADD AN AROMA

Infuse items with the aroma from your favorite dryer fabric softener sheets to keep clothes

and accessories looking, feeling, and smelling refreshed.

REDUCE WRINKLES

The Refresh cycle also uses steam and a moving hanger that vibrates approximately 180

times per minute to reduce the wrinkles in clothing. Performance may vary depending on

fabric type.

SHARPEN CREASES IN PANTS

Hang dress trousers flat in the Styler's Pants Crease Care feature. It will crease the pants

legs.

GENTLY AND EFFECTIVELY DRY

The heat pump drying technology of the Gentle Dry cycle provides low-heat drying which

draws moisture from clothes without the shrinking or damage associated with hot-air

drying. Gently and safely dry alpaca, camelhair and other non-washable fabrics that have

become damp from rain or snow, and wool sweaters, hand-washable knits, and other dry-

flat items after washing.

SANITIZE AND REDUCE ALLERGENS

The Styler's Sanitary cycle uses TrueSteam™ to destroy bacteria and other microorganisms

without damaging clothes. It maintains the optimal temperature necessary to sanitize each

garment, destroying bacteria that persist even when clothes are dried in sunlight.

SMART DIAGNOSIS™

Should you experience any technical difficulty with the Styler, it has the capability of

transmitting data by phone to the Customer Information Center. The call center agent

records the data transmitted from your machine and uses it to analyze the issue, providing

a fast and effective diagnosis. (Refer to page 38.)

Wi-Fi CYCLE DOWNLOAD

Download additional Styler cycles to meet individual needs. Download one

new cycle at a time.

4 IMPORTANT SAFETY INSTRUCTIONS

IMPORTANT SAFETY INSTRUCTIONS

READ ALL INSTRUCTIONS BEFORE USING THE APPLIANCE.

There are many important safety messages in this manual and on your appliance.

Always

read and obey

all safety messages.

WARNING

To reduce the risk of fire or explosion, electric shock, property damage, injury to persons or

death when using this appliance, follow basic safety precautions, including the following:

WARNING

Indicates a hazardous situation which, if not avoided, could result in death

or serious injury.

CAUTION

Indicates a hazardous situation which, if not avoided, may result in minor or

moderate injury, or product damage.

This is the safety alert symbol. This symbol alerts you to potential hazards that can

result in product damage, property damage, or serious bodily harm or death.

The safety alert symbol will be followed by either the hazard signal word

WARNING

or

CAUTION

. These words mean:

• Install the product where the floor is

firm and level.

The product may vibrate

excessively and eventually fall if installed on

an unstable surface, causing damage or injury.

• Keep the front side protected when

transporting the appliance. Do not truck

from the front.

The tempered glass panel on

the front of the appliance may break, causing

damage or injury.

• Properly ground the appliance to conform

with all governing codes and ordinances.

Follow the details in the installation

instructions. Electric shock can result if the

appliance is not properly grounded.

• Install and store the appliance where it

will not be exposed to temperatures below

freezing or exposed to the weather.

Allow

the product to warm to room temperature

before use if it was delivered in winter or at

sub-sero temperature.

• Do not repair or replace any part of the

appliance or attempt any servicing unless

specifically recommended in the user-

maintenance instructions or in published

user-repair instructions that you understand

and have the skills to carry out.

Failure to

follow this warning can cause serious injury,

fire, electric shock, or death.

• Contact an authorized service center

before installing or relocating the Styler

to

avoid injury or product damage when moving

the product.

• When moving the Styler away from the

wall, be careful not to roll over or damage

the power cord.

• The appliance is heavy. Two or more people

are necessary to move and install the

appliance to prevent damage or injury.

• Prior to use, ensure that you are connecting

this product to a dedicated grounded

electrical outlet rated for use with this

product.

It is the user’s responsibility to

replace a standard 2-prong wall outlet with a

standard 3-prong wall outlet.

• Before use, the appliance must be properly

installed as described in this manual.

Electric shock can result if the appliance is not

properly grounded.

• Do not install the Styler where there

may be a danger of the unit falling. The

product is not designed for use on ships

or airplanes.

Check with an authorized LG

service center for use under other special

circumstances.

• Do not tamper with controls.

SAFETY INSTRUCTIONS FOR INSTALLATION

5IMPORTANT SAFETY INSTRUCTIONS

ENGLISH

WARNING

For your safety, the information in this manual must be followed to minimize the risk of fire,

explosion, or electric shock, or to prevent property damage, injury to persons, or death.

SAFETY INSTRUCTIONS FOR INSTALLATION

SAFETY INSTRUCTIONS FOR CONNECTING ELECTRICITY

• Do not, under any circumstances, cut or

remove the ground prong from the power

cord.

To prevent personal injury or damage to

the appliance, the electrical power cord must be

plugged into a properly grounded outlet.

• This appliance must be plugged into a 120-

VAC, 60-Hz grounced outlet protected by

a 15-ampere fuse or circuit breaker.

Failure

to follow these instructions can result in fire,

explosion, or death.

• This appliance must be plugged into a

properly grounded outlet. Electrical shock

can result if the appliance is not properly

grounded. Have the wall outlet and circuit

checked by a qualified electrician to make

sure the outlet is properly grounded.

Failure

to follow these instructions can create an electric

shock hazard and/or a fire hazard.

• Install the appliance where the plug is easily

accessible. Unplug the appliance when not in

use

to avoid risk of fire or electric shock.

• Unplug the appliance before disassembly or

repair

to avoid risk of electric shock.

• The appliance should always be plugged into

its own individual electrical outlet which has

a voltage rating that matches the rating plate.

This provides the best performance and also

prevents overloading house wiring circuits which

could cause a fire hazard from overheated wires.

• Do not use an extension cord to connect to

an outlet.

Doing so could result in a fire or electric

shock.

• Never unplug your appliance by pulling on

the power cord. Always grip the plug firmly

and pull straight out from the outlet.

The

power cord can be damaged, resulting in a risk of

fire and electric shock.

• Contact LG or a qualified repair person

immediately to repair or replace all power

cords that have become frayed or otherwise

damaged. Do not use a cord that shows

cracks or abrasion damage along its length or

at either end.

The power cord can melt, creating

electric shock and/or fire hazard.

• When installing or moving the appliance, be

careful not to pinch, crush, or damage the

power cord.

This will prevent injury and damage

to the appliance from fire and electric shock.

• Do not use a multi socket outlet which is not

properly grounded (portable). Upon using

a properly-grounded multi socket outlet

(portable), use a product with the current

capacity of 15A or higher alone.

Failure to do so

may result in electric shock or fire due to the heat

of multi socket outlet. The power may be shut off

when the circuit breaker is operated.

• To reduce the risk of electric shock, do not

install the appliance in humid spaces such

as a bathroom.

Failure to follow this warning

can cause death, serious injury, fire, electric

shock, or product deformation or malfunction.

• Remove all packing items and dispose of all

shipping materials properly.

Failure to do so

can result in burns, fire, explosion, or death.

• Connect to a properly rated, protected,

and sized power circuit to avoid electrical

overload.

Improper power circuits can melt,

creating electric shock and/or fire hazard.

• Keep all packaging from children.

Packaging

material can be dangerous for children. There

is a risk of suffocation.

• Do not install near another heat source

such as a stove, oven or heater.

Failure

to follow this warning can cause product

deformation, smoke, or fire.

• Do not place candles, smoking materials,

or other flammables on top of the product.

Dripping wax, smoke, or fire can result.

• Remove all protective vinyl film from the

product.

Failure to do so can cause product

damage, smoke, or fire.

6 IMPORTANT SAFETY INSTRUCTIONS

IMPORTANT SAFETY INSTRUCTIONS

READ ALL INSTRUCTIONS BEFORE USING THE APPLIANCE.

WARNING

To reduce the risk of fire or explosion, electric shock, property damage, injury to persons or

death when using this appliance, follow basic safety precautions, including the following:

• Do not place hands or body near steam

nozzle during operation.

The steam is hot

and could cause an injury.

• Do not insert objects into the steam

nozzle.

Excessive noise and fire could result.

• Do not drink the water from the water

supply or drain tanks.

• Do not disassemble or modify the Styler.

• Do not put hands, feet, or metal objects

below the Styler.

• Do not operate the Styler or touch the

power cord with wet hands.

• Keep fingers out of pinch point areas;

clearances between the door and cabinet

are necessarily small. Be careful closing door

when children are nearby.

• This appliance is not intended for use by

persons (including children) with reduced

physical, sensory or mental capabilities,

or lack of experience and knowledge,

unless they have been given supervision

or instruction concerning the use of the

appliance by a person responsible for their

safety.

• Do not place items exposed to cooking

oils in the Styler.

Items contaminated with

cooking oils may contribute to a chemical

reaction that could cause a load to catch fire.

• Do not dry articles that have been

previously cleaned in, washed in, soaked

in, or spotted with gasoline,

dry-cleaning

solvents, or other flammable or explosive

substances, as they give off vapors that could

ignite or explode.

• Do not use heat to dry articles containing

foam rubber or similarly textured rubber-like

materials.

USE

• Do not allow children to play on or in the

appliance. Close supervision of children is

necessary when the appliance is used near

children.

• Do not climb, stand, or hang on the Styler

door or on the shelf or anywhere inside the

appliance.

The appliance could fall over or

be damaged, or other damage or injury could

occur.

• Do not step on the doors to the water

tanks.

The Styler could fall and cause damage

and injury.

• Do not place heavy or dangerous objects

on top of the Styler.

• Do not put live animals inside the Styler.

• Do not allow children to climb into the

product when it is in use.

• In the event of a gas leak (propane/LPG),

ensure adequate ventilation and contact an

authorized service center before resuming

use. Do not touch or disassemble the

electrical outlet of the Styler.

• Do not use or place flammable substances

(chemicals, medicine, cosmetics, etc) near

the Styler

or store them inside the Styler.

Do not place the Styler in the vicinity of

flammable gas.

• Disconnect the power cord immediately

if you hear a noise, smell a strange odor or

detect smoke coming from the appliance.

• In the event of a flood:

Do not go near the

product when its base is submerged under

water. Contact the service center. There is a

risk of electric shock or fire.

• Do not use fabric softeners or products to

eliminate static unless recommended by

the manufacturer of the fabric softener or

product.

7IMPORTANT SAFETY INSTRUCTIONS

ENGLISH

WARNING

To reduce the risk of fire or explosion, electric shock, property damage, injury to persons or

death when using this appliance, follow basic safety precautions, including the following:

• Do not open door during operation.

The

performance of the product may be adversely

affected. If the product is installed on or near

carpet, condensation from escaping hot air or

steam may stain or damage the carpet.

• Do not use the product for other than the

intended purposes.

Damage incurred by

using the product for purposes other than

those specified in this user manual are not

covered by the warranty.

MAINTENANCE AND DISPOSAL

• Wipe foreign objects (such as dust and

water) off the prongs of the power plug

and contact areas regularly.

Do not use a

wet or damp cloth when cleaning the plug.

• Do not use an appliance to dry the interior.

Do not light a candle to remove interior

odors.

• Do not spray water onto the product

directly when cleaning.

A fire or electric

shock may occur.

• Wipe the interior with a dry cloth after use.

• Clean the lint screen before or after each

load.

GROUNDING INSTRUCTIONS

y

This appliance must be grounded.

In

the event of malfunction or breakdown,

grounding will reduce the risk of electric

shock by providing a path of least resistance

for electric current.

y

This appliance must be equipped with

a cord having an equipment-grounding

conductor and a grounding plug.

The

plug must be plugged into an appropriate

outlet that is properly installed and grounded

in accordance with all local codes and

ordinances.

y

Do not modify the plug.

Ifitwillnottthe

outlet, have a proper outlet installed by a

qualiedelectrician.

• Do not use a bleaching agent such as

oxygen or chlorine-based bleaches on the

exterior of the product.

Clorox or OxiClean

may cause discoloration when applied to the

surface of the product.

• Do not use sharp objects when cleaning

or operating the controls.

An electric shock

may occur.

• Avoid hitting the front glass panel with

heavy objects

. Although it is made of

tempered glass, the panel may break in the

event of a strong impact and cause injury.

• Keep product free from rodents, insects,

and other foreign objects.

They may damage

wires, causing fire or electric shock.

• Before the appliance is removed from

service or discarded, remove the door to

the drying compartment.

Cut off the power

plug and destroy the button section to prevent

reuse.

y

This appliance must be connected to

a grounded metal, permanent wiring

system or an equipment-grounding

conductor must be run with the circuit

conductors and connected to the

equipment-grounding terminal or lead on

the appliance.

Electric shock can result if

the appliance is not properly grounded.

WARNING

Improper connection of the equipment-

grounding conductor can result in a risk

of electric shock.

Check with a qualified

electrician or service person if you are

in doubt that the appliance is properly

grounded.

8 PRODUCT OVERVIEW

PRODUCT OVERVIEW

PARTS

moving hanger

interior light

shelf holder

hot air

circulation vent

water

drain tank

water

supply tank

hooks for

Pants Crease Care

door*

clip

steam nozzle

* The door swing can be reversed by the installer to fit the installation location.

Pants Crease Care

aroma filter

shelf

drip tray

9PRODUCT OVERVIEW

ENGLISH

ACCESSORIES

Included Accessories

NOTE

y

Contact the store where the product was purchased or LG customer service at 1-800-243-0000

(1-888-542-2623 in Canada) if any accessories are damaged or missing. Accessories can be

purchased separately online at http://www.lg.com/us

y

For your safety and for extended product life, use only authorized components. The

manufacturer is not responsible for product malfunction or accidents caused by the use of

separately purchased unauthorized components or parts.

y

The images in this guide may be different from the actual components and accessories, which

are subject to change by the manufacturer without prior notice for product improvement

purposes.

2 hangers* pants hanger*

shelf drip tray

*An ordinary metal/plastic hanger can be used if the hook is less than 5/32 in. (4 mm) thick. The hook must fit in

the indentation in the moving hanger snugly. If the fit is too loose, it may result in vibration, noise, and damage

to clothing.

anti-tip kit

4 carpet install spikes

2 rear leveling feet

2 non-skid pads

2 hinge covers

2 rear cap covers

wrench

10 PRODUCT OVERVIEW

THE MOVING HANGER

Hang clothes on the moving hanger using the

hangers provided with the Styler, or use any

plastic or metal hanger that hooks snugly into the

indentations in the moving hanger.

• Use the moving hanger for suits, coats,

jackets, blouses, dresses, skirts, and pants

that don’t require a crease. Use the Pants

Crease Care to crease pants.

• Anything that can be securely placed on a

hanger and steamed or dried without retaining

hanger marks or other damage can be placed

on the moving hanger.

• Dry sweaters or knits on the shelf to avoid

hanger marks.

• Clothing should be securely fastened, with

zippers and buttons closed, so that it does not

fall off the moving hanger during the cycle.

• Arrange clothing so it does not touch the sides

or rear of the cabinet, if possible. Condensation

may form on the interior surface of the cabinet,

and items in contact with the surface may

remain damp at the end of the cycle. Hang

larger items on the diagonal indentations on

the moving hanger.

THE PANTS CREASE CARE

Hang clothes in the Pants Crease Care using

the pants hanger provided with the Styler or any

pants hanger that fits into the hooks above the

door to the Pants Crease Care.

• Open the door to the Pants Crease Care by

pressing the icon on the front.

• The Pants Crease Care keeps pants legs

creased.

• Pants can be pressed while refreshing other

items in the same cycle.

• For optimum results, use the Extra Pants

Care cycle which is designed for use with the

Pants Crease Care feature. This cycle can be

downloaded using the LG ThinQ app and used

as the Downloaded cycle. For instructions,

see

Smart Functions,

page 36, and the

instructions in the application.

CAUTION

• Do not lean on or hang heavy items on the

door of the Pants Crease Care.

The unit may

tip, resulting in damage or injury.

• Do not allow children to play with or hang

onto the door of the Pants Crease Care.

The

unit may tip, resulting in damage or injury.

• Keep fingers out of pinch point areas when

closing the door of the Pants Crease Care.

Supervise nearby children to prevent injuries.

CAUTION

• Do not lean or pull on the moving hanger.

Do not allow children play with or hang

onto the moving hanger.

The unit could tip,

resulting in damage or injury.

NOTE

To avoid double creases, run a steam cycle using

the moving hanger to reduce any existing knife

pleats, and then use the pants press.

11PRODUCT OVERVIEW

ENGLISH

THE SHELF

Use the shelf when styling clothes or other items

that are difficult to hang or that may be damaged

by hang drying.

• Use the shelf for stuffed toys, pillows, hats,

and other accessories.

• Use the shelf for sweaters, knits, lingerie, or

delicate blouses that can show hanger marks,

stretching, or other damage if dried on a

hanger.

• For best drying performance, do not stack

items on the shelf. Dry single items or place

items side by side with space between.

• When not in use, store the shelf on the shelf

holder knobs in the back of the cabinet.

• For instructions on installing the shelf, see

Assembling the Shelf

, page 28. Do not use

the shelf for storing heavy items.

• Arrange items on the shelf so they do not

touch the sides or rear of the cabinet, if

possible. Condensation may form on the

interior surface of the cabinet, and items in

contact with the surface may remain damp at

the end of the cycle.

CHOOSING STYLER FEATURES

item how to style it

suit coat, blazer

moving hanger

coat, jacket (short)

coat (long)

moving hanger

(remove shelf)

dress (short) moving hanger

dress (long)

moving hanger

(remove shelf)

skirt

moving hanger

lightweight blanket, throw

baby blanket

pants (not creased)

shorts

children’s clothes

scarf

moving hanger

or shelf

tie

shawl

lingerie

moving hanger or

shelf (if delicate)

shirt, blouse

pants (creased)

Pants Crease

Care

cap, hat

shelf

stuffed toys

pillow

sweater

knitwear

infant clothes

CAUTION

• Do not use the shelf to store heavy items.

The shelf may fall, resulting in damage or

injury.

• Do not step or sit on the shelf.

The shelf

may fall or the unit may tip, resulting in

damage or injury.

12 INSTALLATION

INSTALLATION

INSTALLATION OVERVIEW

Please read the following installation instructions first after

purchasing this product or transporting it to another location.

PRODUCT SPECIFICATIONS

The appearance and specifications listed in this manual may vary due to constant product improvements.

steam clothing care S3*F**

description

electric machine for maintaining clothing

electrical requirements

please refer to the rating label regarding detailed information

dimensions

17 ½ in. (W) X 23 in. (D) X 72

13

/

16

in. (H), 39 ¾ in. (D with door

open)

445 mm (W) X 585 mm (D) X 1850 mm (H), 1010 mm (D with

door open)

net weight

172 lb (78 kg)

maximum capacity

4 items

power consumption

1500 W

safety device

double overheating safety device, thermal fuse, programming

Check and choose the

proper location

Level the Styler

Reverse the door swing

(if needed)

Connect to grounded outlet

100–130V only

7

3

/4

in.

20cm

2 in.

5cm

2 in.

5cm

Unpack and remove

shipping material

Install carpet spikes

(if needed)

Remove material from

inside and outside of cabinet

13INSTALLATION

ENGLISH

UNPACKING THE STYLER

• Remove tape and any temporary labels

from the Styler before using.

Do not remove any warning labels, the model

and serial number label, or the Tech Sheet

that is located under the front of the Styler.

• To remove any remaining tape or glue, rub

the area briskly with your thumb.

Tape or glue residue can also be easily

removed by rubbing a small amount of liquid

dish soap over the adhesive with your fingers.

Wipe with warm water and dry.

• Do not use sharp instruments, rubbing

alcohol, flammable fluids, or abrasive

cleaners to remove tape or glue.

These products can damage the surface of

the Styler.

WARNING

y

Use two or more people to move and

install the Styler.

Failure to do so can result

in back injury or other injury.

y

The Styler is heavy. Use the wheels at the

bottom of the product to move it.

Push the

Styler slowly from about halfway down the

front side.

y

Keep the Styler upright when moving it.

If

you lay the Styler on its side, refrigerant may

leak and cause the appliance to malfunction.

y

Keep flammable materials and vapors,

such as gasoline, away from the Styler.

Failure to do so can result in fire, explosion,

or death.

CHOOSING THE PROPER LOCATION

Electricity

Install where an outlet is easily accessible.

Use an individual, grounded outlet:120 Volts, 60 Hz, AC, 15 Amps minimum.

WARNING:

Do not plug in multiple appliances in the same outlet

with the Styler.

Overloading house wiring can cause a fire hazard.

To reduce the risk of electric shock, do not install the Styler in a

wet or damp area.

Floor

Floor must be level and solid enough to support 172 lb (78 kg).

Adjust the leveling legs to compensate for any unevenness in the floor.

Do not install on a platform or a weakly supported structure. If installing on

carpeting, see

Installing on Carpeting

, page 17.

Ambient temperature

Temperature must be between 50°F (10°C) and 95°F (35°C).

If the ambient temperature is too low or high, performance may be affected.

Do not install in direct sunlight or where the temperature may fall below

32°F (0°C).

Clearances

Allow at least 18 in. (46 cm) in front to open the door.

Allow at least 2 in. (5 cm) on both sides and between the back of the Styler

and the wall. Allow at least 7 3/4 in. (20 cm) between the top of the Styler and

any overhanging shelves or cabinets.

If the Styler is too close to adjacent items, performance may decrease and

electricity consumption may increase.

14 INSTALLATION

INSTALLATION LOCATION REQUIREMENTS

WARNING

Read all installation instructions completely before installing and operating the

Styler. It is important to review this entire manual before installing and using the Styler.

Clearances

CAUTION

• The floor must be level, with a maximum slope of 1 inch (2.5 cm) under the Styler.

If the

slope is greater than 1 inch (2.5 cm), the appliance cannot be leveled properly.

• Do not install the Styler on a hollow or flexible platform

. Doing so may cause excessive

noise and vibration and result in damage or injury if the product tips over.

The installation requires:

y

A grounded electrical outlet located within

2 ft. (61 cm) of either side of the appliance.

y

A sturdy floor to support the total appliance

weight of 172 lbs (78 kg). The combined

weight of any other laundry appliances

should also be considered.

2

3

/

64

in.

(52 mm)

15

5

/

32

in. (385 mm)

56½ in.

(1435 mm)

16

5

/

16

in.

(415 mm)

72

13

/

16

in.

(1850 mm)

23 in.

(585 mm)

17

1

/

2

in.

(445 mm)

WARNING

• Do not install or store the Styler in an area where it will be exposed to water and/or

weather.

Failure to follow this warning could result in risk of electric shock, injury, or product

damage or malfunction.

15INSTALLATION

ENGLISH



For closet installation, with a door,

minimum ventilation openings in the

top and bottom of the door are required.

Louvered doors with equivalent ventilation

openings are acceptable.

Closet Ventilation Requirements

Closets with doors must have both an upper and

lower vent to prevent heat and moisture buildup

in the closet. One upper vent opening with a

minimum opening of 48 sq. in. (310 cm

2

) must

be installed no lower than 6 feet above the floor.

One lower vent opening with a minimum opening

of 24 sq. in. (155 cm

2

) must be installed no more

than one foot above the floor. One example

shown uses vent grilles in the door.

Installation Spacing for Recessed Area or Closet Installation

There should be at least a little space around the Styler (or any other appliance) to avoid contact with

walls, furniture, or other appliances during operation. Allow a minimum of 1

3

/

16

inch (3 cm) on all sides

of the Styler to avoid increased noise or damage.

48 sq. in.

(310 sq. cm)

24 sq. in.

(155 sq. cm)

3"

(7.6 cm)

3"

(7.6 cm)

Vent

in.

closet door vent

requirements

7 3/4 in.

(20 cm)

2 in.

(5 cm)

2 in.

(5 cm)

18 in. (46 cm)

in front

25 ½ in.

(650mm)

18 in. (455mm)

10 in. (250mm)

Built-In Installation

Wall

2 in. (50 mm)

1

3

/16 in. (30 mm)

1 in. (25 mm)

1

3

/16 in. (30 mm)

Wall

Ceiling

Recommended Installation Spacing

The following clearances are recommended for

the Styler. Although the Styler has been tested

for clearances of 1

3

/

16

inch (3 cm) on the sides

and rear, recommended clearances should be

considered for the following reasons:



Additional space should be considered for

ease of installation and servicing.



Additional space might be required for

wall, door and floor moldings.



Additional space should be considered

on all sides of the Styler to reduce noise

transfer.



Additional laundry appliance spacing

should also be considered.



Minimum vent opening for built-in

installation is 31

½

sq. in. (200 cm

2

).

16 INSTALLATION

LEVELING THE STYLER

y

The appliance is heavy. Two or more

people are required when installing the

Styler. Failure to follow this warning can

cause serious injury or death.

y

To ensure that the Styler provides optimal

performance, it must be level. To minimize

vibration, noise, and unwanted movement, the

floor must be a perfectly level, solid surface.

1 PositiontheStylerinthenallocation.

Checktomakesureitislevel.Ifinstalling

oncarpet,seeInstalling on Carpetingrst.

y

All leveling feet must rest solidly on the

floor. Gently push on the corners of the

Styler to make sure that it does not rock

from corner to corner. Make sure there are

no gaps between the front leveling feet

and the floor.

2 Usethewrench(packagedwiththe

manual)toturnthelevelingfeet.

Unscrew the front feet to raise the Styler or

screw in the feet to lower it. If unable to level

the unit using only the front feet, install the two

rear leveling feet by tipping the unit. Do not lay

the unit down to install the leveling feet.

Raise or lower the unit using the leveling feet

until the Styler is level from side to side and

front to back.

3 WhentheStyleriscompletelystableand

alllevelingfeetarerestingsolidlyonthe

oor,tightenthelockingnuts.

NOTE

Adjust the leveling feet only as far as

necessary to level the Styler.

Extending the

leveling feet more than necessary can cause

the Styler to vibrate.

locking

nut

WARNING

y

To reduce the risk of injury to persons,

adhere to all industry recommended

safety procedures including the use of

long-sleeved gloves and safety glasses.

Failure to follow this warning can cause

serious injury or death.

WARNING

y

The Styler is heavy. Use two or more

people if installing the rear leveling feet.

Failure to do so can result in back injury or

other injury.

y

Keep the Styler upright when moving

and installing it.

If you lay the Styler on

its side, refrigerant may leak and cause

the appliance to malfunction.

CAUTION

Make sure that all leveling feet are

in firm contact with the floor.

If the

Styler is used without leveling, it may

fall, causing injury, damage, or product

malfunction.

17INSTALLATION

ENGLISH

REVERSING THE DOOR

It is possible to reverse the direction of the door

swing. This should be done by the installer at the

time of installation, if desired.

WARNING

Do not attempt to reverse the door swing

yourself.

If the direction of the door swing

needs to be changed after installation, contact

the LG Customer Information Center at

1-800-243-0000 (USA) or 1-888-542-2623

(Canada).

INSTALLING ON CARPETING

If installing the Styler on carpeting, follow these

instructions.

WARNING

y

The Styler is heavy. Use two or more

people to install the rear leveling feet and

carpet spikes.

Failure to do so can result in

back injury or other injury.

y

Keep the Styler upright when moving

and installing it.

If you lay the Styler on

its side, refrigerant may leak and cause the

appliance to malfunction.

1 Movetheunitintoitsnallocationusing

thebackrollers.

2 Installthetworearlevelingfeet.

Tip the unit, do not lay it down, to install the

leveling feet.

3 Leveltheunitfollowingtheinstructionsin

Leveling the Styler.

4 Installthefourcarpetspikes

ontheendsoftheleveling

feet,withtheshorter,

octagonalfacestowardthe

front.

5 Afterthespikeshavebeeninstalled,the

Stylermayneedtobeleveledagain.

If the carpet has very deep pile or padding,

the front feet may need to be extended

slightly to install the drip tray.

• Be sure to check and empty the drip tray often.

• Do not open the unit during operation to avoid

condensation forming on carpet surface,

which may result in surface mold or mildew.

• Keep the bottom of the cabinet dry when

filling or emptying water tanks. Keep the

outside of the water tanks clean and dry to

discourage growth of mold or mildew.

USING NON-SKID PADS

(OPTIONAL)

Non-skid pads prevent the product from shaking

or shifting when opening or closing the door.

1 Clean the ﬂoor to attach the non-skid

pads.

Use a dry rag to remove and clean

foreign objects or moisture. If moisture

remains, the non-skid pads may slip.

2 Adjust the level after placing the Styler in

the installation area.

front

WARNING

y

Take care when handling the carpet spikes.

They are designed to pierce through the

carpet backing and pad and are very sharp.

y

Keep fingers and hands out from under

the spikes

when setting the unit in place to

avoid personal injury or product damage.

18 INSTALLATION

3 Place the adhesive side of the non-skid

pad on the ﬂ oor.

4 Recheck the Styler's levelness.

Push or rock the edges of the appliance gently

to make sure that the Styler does not rock. If

the Styler rocks, level the appliance again.

• The pads may leave a sticky residue when

they are removed. The residue can be

removed with alcohol.

INSTALLING THE ANTI-TIP

DEVICE

• Appliances can tip, resulting in damage or

injuries. Do not operate the unit without the

anti-tip device in place and engaged.

If an anti-tip device is not properly installed,

the appliance could be unexpectedly tipped

by a child or adult standing, sitting, leaning, or

placing excessive weight on an open door or

the interior parts.

• Install the anti-tip device packed with the

Styler to reduce the risk of tipping.

Refer to the instructions provided with the anti-

tip kit for proper anti-tip device installation.

• Check that the anti-tip device is properly

installed.

With the appliance in its final location, make

sure that the slide adjuster on the cord is

adjusted until there is about one inch of slack

in the cord.

• The use of the anti-tip device does not

preclude tipping of the appliance when it is

not properly installed.

ASSEMBLING THE DRIP TRAY

Before using the Styler, insert the drip tray onto

the bottom of the cabinet.

1 Holdthetraysothearrowandletteron

thefrontofthetrayfaceup.

2 Insertonesideofthetrayrst,then

theother.Pushthetrayuntilitslides

completelyin.

3 Todetach,pullonesideoutthentheother.

If the tray collects water, detach it and empty

the water. After emptying it, re-assemble the

tray.

• Do not operate the Styler without

installing the drip tray.

Doing so could lead

to water damage caused by leaking.

INSTALLING CAP COVERS

1 Lineupthenubsonthecap

coverwiththeholesinthetop

cornerofthecabinet.

2 Snapthecapcoverintoplace.

Repeatwiththeremainingcap

coverontheothercorner.

INSTALLING HINGE COVERS

1 OpentheStylerdoor.

2 Snapthehingecoverontothelowerhinge

assemblywiththebentedgeonthefar

sidefromthehinge.

3 Repeatwiththeremaininghingecoveron

theupperhingeassembly.

Remove

backing

This side up

Adhesive

side

B

19OPERATION

ENGLISH

OPERATION

BEFORE USE

Clean the Styler.

Clean the Styler thoroughly and wipe off all dust that accumulated during shipping.

See

Maintenance

, page 40. Do not plug in or operate the appliance until the

interior and exterior have thoroughly dried.

Connect the power supply.

Check if the power supply is connected before use.

Wash dirty clothes if necessary before putting them in the Styler.

The Styler does not have a washing function. Stains and loose dirt from

one item may transfer to others during a cycle. Wash or brush off dust

and dirt, or spot-clean items, to avoid setting stains or transferring dirt or

odors.

CAUTION

y

Do not scratch the Styler with a sharp object or use a detergent that

contains alcohol, bleach, a flammable liquid or an abrasive when removing

any tape or adhesive from the Styler,.

y

Do not peel off the model or serial number label or the technical information

on the rear surface of the Styler.

NOTE

Remove adhesive residue by wiping it off with your thumb or dish detergent.

Unpack accessories.

Unpack the shelf and hangers. For instructions on installing or using accessories,

see

Loading the Styler

, pages 25-28. Accessories can be purchased separately

from the LG Customer Information Center. Call 1-800-243-0000 (USA) or

1-888-542-2623 (Canada).

Assemble the drip tray.

Insert the drip tray at the bottom of the cabinet. See

Assembling the Drip Tray

, page 18.

20 OPERATION

USING THE STYLER

1 PREPARE ITEMS

• Wash clothes first, if needed.

• No heat-sensitive items or items that can be damaged by exposure

to water. See

Choosing Styler-Safe Clothing

, page 21.

• Place items on hangers or the shelf.

• Fasten buttons and close zippers to keep items on moving hangers

and prevent damage.

2 CLEAN LINT FILTER, CHANGE SHEET IN AROMA FILTER

Lift out filter and remove lint from last load for faster and more efficient

performance. Reinstall filter, checking alignment when closing grill. Do

not operate the Styler without the lint filter in place. See

Checking the

Lint Filter

, page 24. If using a fabric softener sheet in the aroma filter,

change it after every use. See

Changing the Aroma Sheet

, page 24.

3 CHECK WATER TANKS

Fill water supply tank if needed. Empty water drain tank if needed. Use

clean tap water in the supply tank for better product performance and

lifespan. Do not use distilled water or reuse water from the drain tank.

See

Checking the Water Tanks

, page 25.

4 LOAD STYLER

Pay attention to fabric care labels and cycle choice. If clothing is

not appropriate for the cycle selected, it may shrink or be seriously

damaged. See

Loading the Styler

, page 25.

Remove all empty hangers to avoid noise, friction, and damage to clothing.

5 TURN ON STYLER

Touch Power to turn on the Styler.

6 SELECT CYCLE

Touch icons to select desired cycle and settings. See the

Cycle

Guide,

page 31.

7 BEGIN CYCLE

Touch and hold Start/Pause to begin cycle. Pause cycle at any time by

touching Start/Pause again. Restart cycle within four minutes of pausing it,

or the Styler shuts off and settings are lost. Do not open door during cycle.

If steam or hot air escape from open door, condensation may collect on

floor or walls, resulting in damage or mold.

8 END OF CYCLE

Remove items when cycle finishes. Leave door open to let hot air

escape. Interior light shuts off after 4 minutes if door is left open.

La page charge ...

LG Electronics S3MFBN Le manuel du propriétaire

Ce manuel convient également à

LG Electronics S3MFBN Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents